Followup of commits 9d21493b4b
and 08baf56108
(net: tx scalability works : trans_start)
(net: txq_trans_update() helper)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Multi queue drivers can
avoid one cache miss (on dev->trans_start) in their start_xmit()
handler.
Exceptions are NETIF_F_LLTX drivers (vxge & tehuti)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unused #include <version.h> in drivers/net/qlge/qlge_ethtool.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With some asic configurations xmit of frames smaller than 60 bytes may
fail.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving netif_napi_del() up the call chain so it will get called from all
exit points.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chip does not do UDP checksum when fragmentation occurs.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was introduced in an earlier net-next patch.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With some asic configurations xmit of frames smaller than 60 bytes may
fail.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving netif_napi_del() up the call chain so it will get called from all
exit points.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The completion interrupt disable routine is only called from the ISR, so
there is no need for irqsave/restore.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chip does not do UDP checksum when fragmentation occurs.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of extraneous ql_cycle_adapter. It's only called from the one
place.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the firmware is issuing events to the driver the events
must be removed from the queue. If the queue overflows, the
firmware will build and special event that captures those that
are lost.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This event will arrive at boot time or after an
MPI processor reset if the firmware failed to initialize.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This worker and it's supporting routines are used for
IDC 'inter-device-communication' events that require
an ACK mailbox command be sent to allow completion
of the request. These requests are originated by
another function wanting to change some common
port paramters. Typical example would be:
1) Change max TX/RX frame size allowed.
2) Change pause parameters.
3) Change loopback mode.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds functionality to get and set port parameters.
Currently it is used to set maximum TX/RX frame sizes. This process is
also capable of setting:
1) Pause type: Standard or Priority based.
2) Loop back mode.
3) Enable Jumbo frame mode (included here...)
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device has more firmware support for link management, setting
TX and RX maximum frame sizes.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This interface will be used for setting things like maximum
frame size, setting WOL, and ACKing changes requested by the FCOE
function.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This organizes a few calls into a function table to enable adding new
devices.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not a logical change but rather a move of the inbound firmware event
handler into it's own function as it will later be called by the outbound
path.
The addition of the mutex is to create exclusive access to the mailbox
commands between inbound and outbound handling.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add function for performing the reset rather than in-line. This function
may later be called by a core dump process.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there are two paths for filling rx buffer queues. One is
used during initialization and the other during runtime. This patch
removes ql_alloc_sbq_buffers() and ql_alloc_lbq_buffers() and replaces
them with a call to the runtime functions ql_update_lbq() and
ql_update_sbq().
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX Buffers are refilled in chunks of 16 at a time before notifying the
hardware with a register write. This can cause several writes to take
place in a given napi poll call. This change causes the write to take place
only once at the end of the call.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of taking/giving the hw semaphore repeatedly when iterating over
several frame to queue route settings, we have the caller hold it until
all are done.
This reduces PCI bus chatter and possible waits.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of taking/giving the semaphore repeatedly when iterating over
several adderesses, we have the caller hold it until all are done. This
reduces PCI bus chatter and possible waits.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting MAC addresses and routing frames to various queues will need to
be done in response to firmware events as well as during initialization.
This change encapsulates the facilities into a single call that can
later me made from other places.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The large receive buffer queue is not properly tracking the current
index in the case where an early exit occurs. This can happen when a
page alloc or dma mapping fails. If this occurs the queue will get
out of sync and invalid indexes can be written to the hardware.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Receive packets were only scaling across 2 of the receive queues. The
value was hardcoded to 2 instead of being based on how many rx queues
were running.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moved the buffer mapping to a point after TSO logic has modified the
iph->check field. We were seeing stale data on the PCIe bus.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We put the skb back if we can't get mapping for it. We don't
want unmapped buffers on our receive buffer queue.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We put the page back if we can't get mapping for it. We don't
want unmapped buffers on our receive buffer queue.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace calls to vlan_hwaccel_rx() and netif_rx().
Thanks to Dave Miller for pointing out the the driver was making
the wrong upcall for passing packets into the stack.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet