When estimating the clock frequency based on the RTC, take seconds into
account in case the Update In Progress (UIP) bit wasn't seen. This can
happen in virtual machines (which may get pre-empted by the hypervisor
at inopportune times) with QEMU emulating the RTC (and in fact not
setting the UIP bit for very long), especially on slow hosts such as
FPGA systems and hardware emulators. This results in several seconds
actually having elapsed before seeing the UIP bit instead of just one
second, and exaggerated timer frequencies.
While updating the comments, they're also fixed to match the code in
that the rising edge of the update flag is detected first, not the
falling edge.
The rising edge gives a more precise point to read the counters in a
virtualised system than the falling edge, resulting in a more accurate
frequency.
It does however mean that we have to also wait for the falling edge
before doing the read of the RTC seconds register, otherwise it seems to
be possible in slow hardware emulation to stray into the interval when
the RTC time is undefined during the update (at least 244uS after the
rising edge of the update flag). This can result in both seconds values
reading the same, and it wrapping to 60 seconds, vastly underestimating
the frequency.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13174/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The sampling of the GIC counter on Malta after observing a rising edge
of the RTC update flag differs slightly between the first and second
sample, with the first sample also calling gic_start_count(). The two
samples should really be taken as similarly as possible to get the most
accurate figure, so move the gic_start_count() call before detecting the
rising edge.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13173/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Early access to the kernel command line requires early access to the FDT
for platforms which pass the command line within the device tree. There
was no common way to retrieve the location of the FDT without incurring
side effects, such as plat_mem_setup which, on Malta at least,
initializes a bunch of other stuff.
This patch adds plat_get_ftd() for IMG platforms.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12988/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit c014d164f2 ("MIPS: Add platform callback before initializing
the L2 cache") added a platform_early_l2_init function in order to allow
platforms to probe for the CM before L2 initialisation is performed, so
that CM GCRs are available to mips_sc_probe.
That commit actually fails to do anything useful, since it checks
mips_cm_revision to determine whether it should call mips_cm_probe but
the result of mips_cm_revision will always be 0 until mips_cm_probe has
been called. Thus the "early" mips_cm_probe call never occurs.
Fix this & drop the useless weak platform_early_l2_init function by
simply calling mips_cm_probe from setup_arch. For platforms that don't
select CONFIG_MIPS_CM this will be a no-op, and for those that do it
removes the requirement for them to call mips_cm_probe manually
(although doing so isn't harmful for now).
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Jaedon Shin <jaedon.shin@gmail.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12475/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If we fail to register any real SMP implementations, fall back to
registering the dummy UP implementation. Otherwise when we build an SMP
kernel & run it on a system where the SMP implementations fail to probe
(eg. QEMU) the kernel will perform a NULL dereference attempting to call
mp_ops->smp_setup() from plat_smp_setup().
Notably this fixes booting kernels with CPS SMP enabled on QEMU, which
doesn't currently implement the CM, CPC or GIC.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Rob Herring <robh@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11223/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move memory configuration to be performed via device tree for the Malta
board. This moves more Malta specific code to malta-dtshim.c, leaving
the rest of the mti-malta code a little more board-agnostic. This will
be useful to share more code between boards, with the device tree
providing the board specifics as intended.
Since we can't rely upon Malta boards running a bootloader capable of
handling devictrees & filling in the required information, a piece of
shim code (malta_dt_shim) is added to consume the (e)memsize variables
provided as part of the bootloader environment (or on the kernel command
line) then generate the DT memory node using the provided values.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: Kumar Gala <galak@codeaurora.org>
Cc: linux-kernel@vger.kernel.org
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Patchwork: https://patchwork.linux-mips.org/patch/11222/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The fw_getmdesc function & fw_memblock_t abstraction is only used by
Malta, and so far as I can tell serves no purpose beyond making the code
less clear than it could be. Remove the useless level of abstraction.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11221/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The default implementation of platform_maar_init is sufficient for Malta
boards where we want to allow speculation in the regions of memory
corresponding to DDR & disallow it elsewhere. Drop the custom
implementation such that the default is used, reducing the duplication
of information provided by the Malta platform code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/10677/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The CM cache error reporting code is not Malta specific and as such it
should live in the mips-cm.c file. Moreover, CM2 and CM3 differ in the
way cache errors are being recorded to the registers so extend the
previous code to add support for the CM3 as well.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10646/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Allow platforms to perform platform-specific steps before configuring
the L2 cache. This is necessary for platforms with CM3 since the L2
parameters no longer live in the Config2 register.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10642/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The majority of SMP platforms handle their IPIs through do_IRQ()
which calls irq_{enter/exit}(). When a call function IPI is received,
smp_call_function_interrupt() is called which also calls
irq_{enter,exit}(), meaning irq_count is raised twice.
When tick broadcasting is used (which is implemented via a call
function IPI), this incorrectly causes all CPU idle time on the core
receiving broadcast ticks to be accounted as time spent servicing
IRQs, as account_process_tick() will account as such if irq_count is
greater than 1. This results in 100% CPU usage being reported on a
core which receives its ticks via broadcast.
This patch removes the SMP smp_call_function_interrupt() wrapper which
calls irq_{enter,exit}(). Platforms which handle their IPIs through
do_IRQ() now call generic_smp_call_function_interrupt() directly to
avoid incrementing irq_count a second time. Platforms which don't
(loongson, sgi-ip27, sibyte) call generic_smp_call_function_interrupt()
wrapped in irq_{enter,exit}().
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10770/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On Malta, since commit a87ea88d8f ("MIPS: Malta: initialise the RTC at
boot"), the RTC is reinitialised and forced into binary coded decimal
(BCD) mode during init, even if the bootloader has already initialised
it, and may even have already put it into binary mode (as YAMON does).
This corrupts the current time, can result in the RTC seconds being an
invalid BCD (e.g. 0x1a..0x1f) for up to 6 seconds, as well as confusing
YAMON for a while after reset, enough for it to report timeouts when
attempting to load from TFTP (it actually uses the RTC in that code).
Therefore only initialise the RTC to the extent that is necessary so
that Linux avoids interfering with the bootloader setup, while also
allowing it to estimate the CPU frequency without hanging, without a
bootloader necessarily having done anything with the RTC (for example
when the kernel is loaded via EJTAG).
The divider control is configured for a 32KHZ reference clock if
necessary, and the SET bit of the RTC_CONTROL register is cleared if
necessary without changing any other bits (this bit will be set when
coming out of reset if the battery has been disconnected).
Fixes: a87ea88d8f ("MIPS: Malta: initialise the RTC at boot")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.14+
Patchwork: https://patchwork.linux-mips.org/patch/10739/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Wider testing reveals that the Fast Debug Channel (FDC) interrupt is
routed through the GIC just fine on Pistachio SoC, even though it
contains interAptiv cores. Clearly the FDC interrupt routing problems
previously observed on interAptiv and proAptiv cores are specific to the
Malta FPGA bitstreams.
Move the workaround for interAptiv and proAptiv out of
gic_get_c0_fdc_int() in the GIC irqchip driver into Malta's
get_c0_fdc_int() platform callback, to allow the Pistachio SoC to use
the FDC interrupt.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hartley <james.hartley@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/9748/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Build a DT for the Malta platform into the kernel, load it & probe
devices from it. The DT is essentially empty at this point, devices
will be added in further patches.
[ralf@linux-mips.org: Fixed conflicts.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/10119/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Here's the big tty/serial driver update for 4.1-rc1.
It was delayed for a bit due to some questions surrounding some of the
console command line parsing changes that are in here. There's still
one tiny regression for people who were previously putting multiple
console command lines and expecting them all to be ignored for some odd
reason, but Peter is working on fixing that. If not, I'll send a revert
for the offending patch, but I have faith that Peter can address it.
Other than the console work here, there's the usual serial driver
updates and changes, and a buch of 8250 reworks to try to make that
driver easier to maintain over time, and have it support more devices in
the future.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlU2IcUACgkQMUfUDdst+ylFqACcC8LPhFEZg9aHn0hNUoqGK3rE
5dUAnR4b8r/NYqjVoE9FJZgZfB/TqVi1
=lyN/
-----END PGP SIGNATURE-----
Merge tag 'tty-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here's the big tty/serial driver update for 4.1-rc1.
It was delayed for a bit due to some questions surrounding some of the
console command line parsing changes that are in here. There's still
one tiny regression for people who were previously putting multiple
console command lines and expecting them all to be ignored for some
odd reason, but Peter is working on fixing that. If not, I'll send a
revert for the offending patch, but I have faith that Peter can
address it.
Other than the console work here, there's the usual serial driver
updates and changes, and a buch of 8250 reworks to try to make that
driver easier to maintain over time, and have it support more devices
in the future.
All of these have been in linux-next for a while"
* tag 'tty-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
n_gsm: Drop unneeded cast on netdev_priv
sc16is7xx: expose RTS inversion in RS-485 mode
serial: 8250_pci: port failed after wakeup from S3
earlycon: 8250: Document kernel command line options
earlycon: 8250: Fix command line regression
earlycon: Fix __earlycon_table stride
tty: clean up the tty time logic a bit
serial: 8250_dw: only get the clock rate in one place
serial: 8250_dw: remove useless ACPI ID check
dmaengine: hsu: move memory allocation to GFP_NOWAIT
dmaengine: hsu: remove redundant pieces of code
serial: 8250_pci: add Intel Tangier support
dmaengine: hsu: add Intel Tangier PCI ID
serial: 8250_pci: replace switch-case by formula for Intel MID
serial: 8250_pci: replace switch-case by formula
tty: cpm_uart: replace CONFIG_8xx by CONFIG_CPM1
serial: jsm: some off by one bugs
serial: xuartps: Fix check in console_setup().
serial: xuartps: Get rid of register access macros.
serial: xuartps: Fix iobase use.
...
memsize denotes the amount of RAM we can access from kseg{0,1} and
that should be up to 256M. In case the bootloader reports a value
higher than that (perhaps reporting all the available RAM) it's best
if we fix it ourselves and just warn the user about that. This is
usually a problem with the bootloader and/or its environment.
[ralf@linux-mips.org: Remove useless parens as suggested bei Sergei.
Reformat long pr_warn statement to fit into 80 column limit.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9362/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Implement the weak get_c0_fdc_int() function for Malta. The Fast Debug
Channel (FDC) interrupt is obtained mainly depending on whether a GIC is
present. Vectored external interrupt mode isn't yet supported.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9143/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Implement mips_cdmm_phys_base() for Malta, returning the physical base
address 0x1fc10000 which is "typically unused".
This allows the Common Device Memory Map (CDMM) region to be mapped, and
devices in that region (such as the Fast Debug Channel (FDC) hardware
for communication over EJTAG) to be discovered.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9177/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
setup_earlycon() will now match and register the desired earlycon
from the param string (as if 'earlycon=...' had been set on the
command line). Use setup_earlycon() from existing arch call sites
which start an earlycon directly.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no reason for gic_frequency to be global any more and it
certainly doesn't belong in the GIC irqchip driver, so move it to
the GIC clocksource driver.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8137/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the GIC clocksource driver to drivers/clocksource/mips-gic-timer.c.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8133/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that the MIPS GIC irqchip lives in drivers/irqchip/, move
its header over to include/linux/irqchip/.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8129/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Stop using the REG macros from gic.h and instead use proper iomem
accessors.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8126/
Patchwork: https://patchwork.linux-mips.org/patch/8227/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Instead of reading the GIC registers directly, use the interface the GIC
driver already exposes for reading the global timer. Also get rid of
the unnecessary #ifdefs.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8123/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The generic plat_irq_dispatch provided in irq_cpu.c is sufficient for
dispatching interrupts on Malta in legacy and vectored interrupt modes.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7821/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MIPS GIC supports 7 local interrupts, 2 of which are the GIC
local watchdog and count/compare timer. The remainder are CPU
interrupts which may optionally be re-routed through the GIC.
GIC hardware IRQs 0-6 are now used for local interrupts while
hardware IRQs 7+ are used for external (shared) interrupts.
Note that the 5 CPU interrupts may not be re-routable through
the GIC. In that case mapping will fail and the vectors reported
in C0_IntCtl should be used instead. gic_get_c0_compare_int() and
gic_get_c0_perfcount_int() will return the correct IRQ number to
use for the C0 timer and perfcounter interrupts based on the
routability of those interrupts through the GIC.
A separate irq_chip, with callbacks that mask/unmask the local
interrupt on all CPUs, is used for the C0 timer and performance
counter interrupts since all other platforms do not use the percpu
IRQ API for those interrupts.
Malta, SEAD-3, and the GIC clockevent driver have been updated
to use local interrupts and the R4K clockevent driver has been
updated to poll for C0 timer interrupts through the GIC when
the GIC is present.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7819/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that the GIC properly uses IRQ domains, kill off the per-platform
routing tables that were used to make the GIC appear transparent.
This includes:
- removing the mapping tables and the support for applying them,
- moving GIC IPI support to the GIC driver,
- properly routing the i8259 through the GIC on Malta, and
- updating IRQ assignments on SEAD-3 when the GIC is present.
Platforms no longer will pass an interrupt mapping table to gic_init.
Instead, they will pass the CPU interrupt vector (2 - 7) that they
expect the GIC to route interrupts to. Note that in EIC mode this
value is ignored and all GIC interrupts are routed to EIC vector 1.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7816/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use a simple IRQ domain for the MIPS GIC. Remove the gic_platform_init
callback as it's no longer necessary for it to set the irqchip.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7811/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There's no need for platforms to have their own GIC irq_ack/irq_eoi
callbacks. irq_ack need only clear the GIC's edge detector on
edge-triggered interrupts and there's no need at all for irq_eoi.
Also get rid of the mask_ack callback since it's not necessary either.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7809/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move GIC irqchip support to drivers/irqchip/ and rename the Kconfig
option from IRQ_GIC to MIPS_GIC to avoid confusion with the ARM GIC.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7812/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The hardware perf event driver and oprofile interpret the global
cp0_perfcount_irq differently: in the hardware perf event driver
it is an offset from MIPS_CPU_IRQ_BASE and in oprofile it is the
actual IRQ number. This still works most of the time since
MIPS_CPU_IRQ_BASE is usually 0, but is clearly wrong. Since the
performance counter interrupt may vary from platform to platform
like the C0 timer interrupt, add the optional get_c0_perfcount_int
hook which returns the IRQ number of the performance counter.
The hook should return < 0 if the performance counter interrupt is
shared with the timer. If the hook is not present, the CPU vector
reported in C0_IntCtl (cp0_perfcount_irq) is used.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7805/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The malta-amon.c file provides functions to access the YAMON Monitoring
interface to bring up secondary VPEs in case of SMP/CMP. As a
result of which, there is no need to build it if CMP is not used.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/7993/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Using kstrtol to parse the "{e,}memsize" variables was wrong because this
parses signed long numbers. In case of '{e,}memsize' >= 2G, the top bit
is set, resulting to -ERANGE errors and possibly random system memory
boundaries. We fix this by replacing "kstrtol" with "kstrtoul".
We also improve the code to check the kstrtoul return value and
print a warning if an error was returned.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7543/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Initialise the MAARs such that speculation is enabled for all physical
addresses outside of the I/O region.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7333/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Malta malta_ipi_irqdispatch() routine now checks only IPI interrupts
when handling IPIs. It could previously call do_IRQ() for non-IPIs, and
also call do_IRQ() with an invalid IRQ number if there were no pending
GIC interrupts when gic_get_int() was called.
Signed-off-by: Jeffrey Deans <jeffrey.deans@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7377/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
irq-gic.c:gic_get_int() masks out interrupts from the pending set which
aren’t in the pcpu_mask. Only interrupts marked with GIC_FLAG_IPI were
set in pcpu_mask, meaning that peripheral interrupts also had to be
marked as IPIs. Remove the use of GIC_FLAG_IPI and allow the flags
member of struct gic_intr_map to be zero.
Signed-off-by: Jeffrey Deans <jeffrey.deans@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7374/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
- three fixes for 3.15 that didn't make it in time
- limited Octeon 3 support.
- paravirtualization support
- improvment to platform support for Netlogix SOCs.
- add support for powering down the Malta eval board in software
- add many instructions to the in-kernel microassembler.
- add support for the BPF JIT.
- minor cleanups of the BCM47xx code.
- large cleanup of math emu code resulting in significant code size
reduction, better readability of the code and more accurate
emulation.
- improvments to the MIPS CPS code.
- support C3 power status for the R4k count/compare clock device.
- improvments to the GIO support for older SGI workstations.
- increase number of supported CPUs to 256; this can be reached on
certain embedded multithreaded ccNUMA configurations.
- various small cleanups, updates and fixes
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (173 commits)
MIPS: IP22/IP28: Improve GIO support
MIPS: Octeon: Add twsi interrupt initialization for OCTEON 3XXX, 5XXX, 63XX
DEC: Document the R4k MB ASIC mini interrupt controller
DEC: Add self as the maintainer
MIPS: Add microMIPS MSA support.
MIPS: Replace calls to obsolete strict_strto call with kstrto* equivalents.
MIPS: Replace obsolete strict_strto call with kstrto
MIPS: BFP: Simplify code slightly.
MIPS: Call find_vma with the mmap_sem held
MIPS: Fix 'write_msa_##' inline macro.
MIPS: Fix MSA toolchain support detection.
mips: Update the email address of Geert Uytterhoeven
MIPS: Add minimal defconfig for mips_paravirt
MIPS: Enable build for new system 'paravirt'
MIPS: paravirt: Add pci controller for virtio
MIPS: Add code for new system 'paravirt'
MIPS: Add functions for hypervisor call
MIPS: OCTEON: Add OCTEON3 to __get_cpu_type
MIPS: Add function get_ebase_cpunum
MIPS: Add minimal support for OCTEON3 to c-r4k.c
...
was a pretty active cycle for KVM. Changes include:
- a lot of s390 changes: optimizations, support for migration,
GDB support and more
- ARM changes are pretty small: support for the PSCI 0.2 hypercall
interface on both the guest and the host (the latter acked by Catalin)
- initial POWER8 and little-endian host support
- support for running u-boot on embedded POWER targets
- pretty large changes to MIPS too, completing the userspace interface
and improving the handling of virtualized timer hardware
- for x86, a larger set of changes is scheduled for 3.17. Still,
we have a few emulator bugfixes and support for running nested
fully-virtualized Xen guests (para-virtualized Xen guests have
always worked). And some optimizations too.
The only missing architecture here is ia64. It's not a coincidence
that support for KVM on ia64 is scheduled for removal in 3.17.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=j5Od
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm into next
Pull KVM updates from Paolo Bonzini:
"At over 200 commits, covering almost all supported architectures, this
was a pretty active cycle for KVM. Changes include:
- a lot of s390 changes: optimizations, support for migration, GDB
support and more
- ARM changes are pretty small: support for the PSCI 0.2 hypercall
interface on both the guest and the host (the latter acked by
Catalin)
- initial POWER8 and little-endian host support
- support for running u-boot on embedded POWER targets
- pretty large changes to MIPS too, completing the userspace
interface and improving the handling of virtualized timer hardware
- for x86, a larger set of changes is scheduled for 3.17. Still, we
have a few emulator bugfixes and support for running nested
fully-virtualized Xen guests (para-virtualized Xen guests have
always worked). And some optimizations too.
The only missing architecture here is ia64. It's not a coincidence
that support for KVM on ia64 is scheduled for removal in 3.17"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (203 commits)
KVM: add missing cleanup_srcu_struct
KVM: PPC: Book3S PR: Rework SLB switching code
KVM: PPC: Book3S PR: Use SLB entry 0
KVM: PPC: Book3S HV: Fix machine check delivery to guest
KVM: PPC: Book3S HV: Work around POWER8 performance monitor bugs
KVM: PPC: Book3S HV: Make sure we don't miss dirty pages
KVM: PPC: Book3S HV: Fix dirty map for hugepages
KVM: PPC: Book3S HV: Put huge-page HPTEs in rmap chain for base address
KVM: PPC: Book3S HV: Fix check for running inside guest in global_invalidates()
KVM: PPC: Book3S: Move KVM_REG_PPC_WORT to an unused register number
KVM: PPC: Book3S: Add ONE_REG register names that were missed
KVM: PPC: Add CAP to indicate hcall fixes
KVM: PPC: MPIC: Reset IRQ source private members
KVM: PPC: Graciously fail broken LE hypercalls
PPC: ePAPR: Fix hypercall on LE guest
KVM: PPC: BOOK3S: Remove open coded make_dsisr in alignment handler
KVM: PPC: BOOK3S: Always use the saved DAR value
PPC: KVM: Make NX bit available with magic page
KVM: PPC: Disable NX for old magic page using guests
KVM: PPC: BOOK3S: HV: Add mixed page-size support for guest
...
This patch powers down the Malta in response to a power off command (eg.
poweroff or shutdown -P). It may then be powered back up by pressing the
"ON/NMI" button (S4) on the board. In cases where the power off state
cannot be entered (eg. because the required PCI support is disabled) the
current reset behaviour will be used as a fallback.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Tested-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6907/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When the system is halted it makes little sense to reset it. Instead,
hang by executing an infinite loop.
[ralf@linux-mips.org: Remove printk from mips_machine_halt() - this is not
the place to communicate with the user.]
Suggested-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6906/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch introduces code which will enter a suspend state via the
PIIX4. This can only be done when PCI support is enabled since it
requires access to PCI I/O space and the generation of a special cycle
on the PCI bus. In cases where PCI is disabled the mips_pm_suspend
function will simply always return an error.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6905/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The KVM_HOST_FREQ Kconfig symbol was used by KVM guest kernels to
override the timer frequency calculation to a value based on the host
frequency. Now that the KVM timer emulation is implemented independent
of the host timer frequency and defaults to 100MHz, adjust the working
of CONFIG_KVM_HOST_FREQ to match.
The Kconfig symbol now specifies the guest timer frequency directly, and
has been renamed accordingly to KVM_GUEST_TIMER_FREQ. It now defaults to
100MHz too and the help text is updated to make it clear that a zero
value will allow the normal timer frequency calculation to take place
(based on the emulated RTC).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Sanjay Lal <sanjayl@kymasys.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
First introduced in e6ca4e5bf1
"MIPS: malta: malta-memory: Add support for the 'ememsize' variable"
but it is not needed since both variables are visible to the compiler.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6985/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
James Hogan