After 2.6.34 changes, __pxa2xx_drv_pcmcia_probe() was replaced by
sa1111_pcmcia_add(). That unfortunately means that configure_sockets()
is not called, leading to MECR not being set properly, leading to
strange crashes.
Tested on pxa255+sa1111, I do not have lubbock board nearby. Perhaps
cleaner solution exists?
Signed-off-by: Pavel Machek <pma@sysgo.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
This patch adds nanoEngine PCMCIA support, with support for two sockets.
In order to have a fully functional pcmcia subsystem in a BSE
nanoEngine board you should carefully read this:
http://cambuca.ldhs.cetuc.puc-rio.br/nanoengine/
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes checkpatch.pl issues in drivers/pcmcia/soc_common.c.
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The new FPGA firmware in Balloon3 uses different methods to control it's bus
control lines. In the new version, there are separate registers to set/clear
bus control lines. This patch updates affected places.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This driver also contains structures to eventually support PXA320. This is
planned to be added in a later patch.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
On PXA320, there's only one PCMCIA slot available. Check for cases where the
user would want to register multiple. Also, rework failpath.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This is important because on PXA3xx, the physical mapping of SMEMC registers
differs from the one on PXA2xx. In order to get PCMCIA working on both PXA2xx
and PXA320, the PCMCIA driver was adjusted accordingly as well.
Also, various places in the kernel had to be patched to use
__raw_read/__raw_write.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch fixes a compilation issue when compiling PCMCIA SA1100
support as a module with PCMCIA_DEBUG enabled. The symbol
soc_pcmcia_debug was not beeing exported.
ARM: pcmcia: Fix for building DEBUG with sa11xx_base.c as a module.
This patch fixes a compilation issue when compiling PCMCIA SA1100
support as a module with PCMCIA_DEBUG enabled. The symbol
soc_pcmcia_debug was not beeing exported.
Cc: <stable@kernel.org>
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Using %pV reduces the number of printk calls and
eliminates any possible message interleaving from
other printk calls.
Signed-off-by: Joe Perches <joe@perches.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Eric Miao <eric.y.miao@gmail.com>
CC: linux-arm-kernel@lists.infradead.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
These are called by sa11x0_drv_pcmcia_probe (which is marked now with
__devinit) so they can go to .devinit.text now, too.
This fixes:
WARNING: drivers/pcmcia/sa1100_cs.o(.text+0x10): Section mismatch in reference from the function sa11x0_drv_pcmcia_probe() to the function .init.text:pcmcia_simpad_init()
The function sa11x0_drv_pcmcia_probe() references
the function __init pcmcia_simpad_init().
This is often because sa11x0_drv_pcmcia_probe lacks a __init
annotation or the annotation of pcmcia_simpad_init is wrong.
and a similar warning for pcmcia_collie_init, pcmcia_cerf_init,
pcmcia_h3600_init and pcmcia_shannon_init.
While at it mark pcmcia_assabet_init with __devinit, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
CC: Russell King <linux@arm.linux.org.uk>
CC: Eric Miao <eric.y.miao@gmail.com>
CC: linux-arm-kernel@lists.infradead.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Dave Hinds pointed out to me that 37979e1546 will break b43 and
ray_cs, as IOCARD is not -- as the name would suggest -- only needed
for cards using IO ports. Instead, as it re-deines several pins, it
is also required for using interrupts.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
au100_generic and soc_common call flush_scheduled_work() spuriously.
Remove them.
This is to prepare for the deprecation and removal of
flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Some cards need the speedups on, some need them off. As we can't detect
this reliably, at least give the users a hint how to tweak the system.
Reported-by: David Bluecame <david.bluecame@gmail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
pcmcia_socket_dev_resume() is only referenced from macro
SET_SYSTEM_SLEEP_PM_OPS(NULL, pcmcia_socket_dev_resume)
which based on CONFIG_PM_SLEEP may or may not actually
use its second parameter.
Signed-off-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
- pci_release_regions called during return error path.
- pci_disable_device called for cases where earlier it was enabled.
- code duplication avoided/reduced by adding resource release at goto statements.
Signed-off-by: Rahul Ruikar <rahul.ruikar@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Fill in missing descriptions and update some others for functions in
pcmcia_resource.c.
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The Status (CISREG_CCSR) and ExtStatus (CISREG_ESR) registers were
only accessed to enable audio output for some drivers and IRQ for
serial_cs.c. The former also required setting config_req_t.Attributes
to CONF_ENABLE_SPKR; the latter can be simplified to setting this
field to CONF_ENABLE_ESR.
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-serial@vger.kernel.org
CC: linux-scsi@vger.kernel.org
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The "Pin" and "Copy" configuration registers (CISREG_SCR, CISREG_PPR)
do not seem to be utilized anywhere. If a device would request a
write to these registers, "0" would be written. Continue to do so, but
warn of unexpected behavior -- and remove the "Pin" and "Copy" entries
from config_req_t.
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
pcmcia_modify_configuration() was only used by two drivers to fix up
one issue each: setting the Vpp to a different value, and reducing
the IO width to 8 bit. Introduce two explicitly named functions
handling these things, and remove one further typedef.
CC: netdev@vger.kernel.org
CC: linux-mtd@lists.infradead.org
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Instead of win_req_t, drivers are now requested to fill out
struct pcmcia_device *p_dev->resource[2,3,4,5] for up to four iomem
ranges. After a call to pcmcia_request_window(), the windows found there
are reserved and may be used until pcmcia_release_window() is called.
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-mtd@lists.infradead.org
CC: Jiri Kosina <jkosina@suse.cz>
CC: linux-scsi@vger.kernel.org
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
If pcmcia_request_io() only fails partly -- for the second of two
requested resources -- preserve the configuration settings for the
first one.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As the iomem / ioport setup differs per device, it is much better
to print out the device instead of the socket.
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: avoid buffer overflow in pcmcia_setup_isa_irq
pcmcia: do not request windows if you don't need to
pcmcia: insert PCMCIA device resources into resource tree
pcmcia: export resource information to sysfs
pcmcia: use struct resource for PCMCIA devices, part 2
pcmcia: remove memreq_t
pcmcia: move local definitions out of include/pcmcia/cs.h
pcmcia: do not use io_req_t when calling pcmcia_request_io()
pcmcia: do not use io_req_t after call to pcmcia_request_io()
pcmcia: use struct resource for PCMCIA devices
pcmcia: clean up cs.h
pcmcia: use pcmica_{read,write}_config_byte
pcmcia: remove cs_types.h
pcmcia: remove unused flag, simplify headers
pcmcia: remove obsolete CS_EVENT_ definitions
pcmcia: split up central event handler
pcmcia: simplify event callback
pcmcia: remove obsolete ioctl
Conflicts in:
- drivers/staging/comedi/drivers/*
- drivers/staging/wlags49_h2/wl_cs.c
due to dev_info_t and whitespace changes
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (150 commits)
MIPS: PowerTV: Separate PowerTV USB support from non-USB code
MIPS: strip the un-needed sections of vmlinuz
MIPS: Clean up the calculation of VMLINUZ_LOAD_ADDRESS
MIPS: Clean up arch/mips/boot/compressed/decompress.c
MIPS: Clean up arch/mips/boot/compressed/ld.script
MIPS: Unify the suffix of compressed vmlinux.bin
MIPS: PowerTV: Add Gaia platform definitions.
MIPS: BCM47xx: Fix nvram_getenv return value.
MIPS: Octeon: Allow more than 3.75GB of memory with PCIe
MIPS: Clean up notify_die() usage.
MIPS: Remove unused task_struct.trap_no field.
Documentation: Mention that KProbes is supported on MIPS
SAMPLES: kprobe_example: Make it print something on MIPS.
MIPS: kprobe: Add support.
MIPS: Add instrunction format for BREAK and SYSCALL
MIPS: kprobes: Define regs_return_value()
MIPS: Ritually kill stupid printk.
MIPS: Octeon: Disallow MSI-X interrupt and fall back to MSI interrupts.
MIPS: Octeon: Support 256 MSI on PCIe
MIPS: Decode core number for R2 CPUs.
...
Remove the CONFIG_SOC_AU1X00 Kconfig symbol since its job can also be done
by MACH_ALCHEMY, now renamed to MIPS_ALCHEMY.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1461/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
NR_IRQS may be as low as 16, causing a (harmless?) buffer overflow in
pcmcia_setup_isa_irq():
static u8 pcmcia_used_irq[NR_IRQS];
...
if ((try < 32) && pcmcia_used_irq[irq])
continue;
This is read-only, so if this address would be non-zero, it would just
mean we would not attempt an IRQ >= NR_IRQS -- which would fail anyway!
And as request_irq() fails for an irq >= NR_IRQS, the setting code path:
pcmcia_used_irq[irq]++;
is never reached as well.
Reported-by: Christoph Fritz <chf.fritz@googlemail.com>
CC: stable@kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Insert PCMCIA device resources into the resource tree. However, this is
currently only implemented for sockets which do not statically map the
resources.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Introduce a new field into struct pcmcia_device named "resource" and of
type struct resource *, which contains the IO port ranges allocated for
this device. Memory window ranges and registration with the resource
trees will follow at a later date.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As we only provide one way to set up resources now, we can remove
the resource-setup-related bitfield (except resource_setup_done).
In addition, pcmcia_state only consisted of one entry, so remove
this bitfield as well.
Suggested-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The event callback for handling 16bit PCMCIA cards only needs to be
informed about a few events. Furthermore, send_event may already
only be called with skt->skt_mutex held, which also protects against
the module being removed behind the callback's back.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Up to 2.6.34 pcmcia_release_irq() reset p_dev->_irq to 0 after releasing
the irq. The IRQ is now released in pcmcia_disable_device(), however
p_dev->_irq is not reset, triggering a warning in pcmcia_device_remove().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The MCxx values must be based off memory clock, not CPU core clock.
This also fixes the bug where on some machines the LCD went crazy
while using PCMCIA.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The "present" flag was initialized too late -- possibly, a card
was already registered at this time, so re-setting the flag to 0
caused pcmcia_dev_present() to fail.
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Commit a8408c17 introduced a new check to pccard_validate_cis(),
which avoids any "late" calls to this function. This broke the
insertion of cards which require a CIS override which changes
the number of card functions. Fix this by asserting that this
is _not_ a late call, but a proper call early during the card
insertion process.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=16138
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
CC: <stable@kernel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Seems pointless to have two #ifdef's with the same
CONFIG_YENTA_TI. Remove the extra one and
move CARDBUS_TYPE_ENE with the others.
[linux@dominikbrodowski.net: spelling & whitespace fixes]
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Keeping the saved I365_CSCINT flag around breaks PCMCIA on some system,
and is only needed on a few systems to get PCMCIA to work. This patch
allows PCMCIA to work on both types, and it fixes
https://bugzilla.kernel.org/show_bug.cgi?id=16015
Reported-by: Justin P. Mattock <justinmattock@gmail.com>
CC: <stable@kernel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Fixes build errors caused by the:
- OF device_node pointer being moved into struct device
- typo in match_table field in the struct device_driver
(which shoud be of_match_table)
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'bkl/ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/random-tracing:
uml: Pushdown the bkl from harddog_kern ioctl
sunrpc: Pushdown the bkl from sunrpc cache ioctl
sunrpc: Pushdown the bkl from ioctl
autofs4: Pushdown the bkl from ioctl
uml: Convert to unlocked_ioctls to remove implicit BKL
ncpfs: BKL ioctl pushdown
coda: Clean-up whitespace problems in pioctl.c
coda: BKL ioctl pushdown
drivers: Push down BKL into various drivers
isdn: Push down BKL into ioctl functions
scsi: Push down BKL into ioctl functions
dvb: Push down BKL into ioctl functions
smbfs: Push down BKL into ioctl function
coda/psdev: Remove BKL from ioctl function
um/mmapper: Remove BKL usage
sn_hwperf: Kill BKL usage
hfsplus: Push down BKL into ioctl function
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
These are the last remaining device drivers using
the ->ioctl file operation in the drivers directory
(except from v4l drivers).
[fweisbec: drop i8k pushdown as it has been done from
procfs pushdown branch already]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
While pci_set_power_state() is called by the PCI core
unconditionally on all PCI devices, it is not called on _any_
PCI bridge device. Therefore, it is not surprising calling
pci_set_power_state() on CardBus devices causes trouble.
CC: dbrownell@users.sourceforge.net
CC: gregkh@suse.de
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As all cards to pcmcia_device_add() are already locked by skt_mutex, and
the critical sections inside this function are further protected by
ops_mutex, there's no need to keep a third lock around. Therfore, remove
pcmcia_add_device_lock.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
On the PCI root bus on the x86 architecture, the risk of hitting
some strange system devices is too high: If a driver isn't loaded,
the resources are not claimed; even if a driver is loaded, it
may not request all resources or even the wrong one. We can neither
trust the rest of the kernel nor ACPI/PNP and CRS parsing to get it
right.
Therefore, explicitly spell out what safeguards we provide, and add
a safeguard to only use resources which are set up exclusively for
the secondary PCI bus (non-subtractive mode): the risk of hitting
system devices is quite low, as they usually aren't connected to
the secondary PCI bus.
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Clean up the alloc_io_space() function by moving most of it to
the actual resource_ops. This allows for a bit less re-directions.
Future cleanups will follow, and will make up for the code
duplication currently present between rsrc_iodyn and rsrc_nonstatic
(which are hardly ever built at the same time anyway, therefore no
increase in built size).
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Remove the dev_node declaration. We now only pass the device name
to the deprecated userspace tools.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Instead of the old pcmcia_request_irq() interface, drivers may now
choose between:
- calling request_irq/free_irq directly. Use the IRQ from *p_dev->irq.
- use pcmcia_request_irq(p_dev, handler_t); the PCMCIA core will
clean up automatically on calls to pcmcia_disable_device() or
device ejection.
- drivers still not capable of IRQF_SHARED (or not telling us so) may
use the deprecated pcmcia_request_exclusive_irq() for the time
being; they might receive a shared IRQ nonetheless.
CC: linux-bluetooth@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-serial@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: linux-usb@vger.kernel.org
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As it's only used there it makes no sense relying on pcmcia_request_irq().
CC: alsa-devel@alsa-project.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Setup the IRQ to be used by PCMCIA drivers already during the device
registration stage, making use of a new function pcmcia_setup_irq().
This will allow us to get rid of quite a lot of indirection in the
future.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: fix compilation after 16bit state locking changes
pcmcia: order userspace suspend and resume requests
pcmcia: avoid pccard_validate_cis failure in resume callpath
Commit 04de0816 (pcmcia: pcmcia_dev_present bugfix) broke the
deprecated ioctl layer. Fix it by getting rid of references to
unexisting fields.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Assert that userspace suspend and resume requests appearing
(almost) immediately are executed in the following order:
suspend, resume. This should result in "pccardctl reset"
behaving the same as before.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
If the PCMCIA CIS changed before a resume event (e.g. due to
a card exchange while being suspended, possibly also during
a call to "pccardctl reset"), also set the function count to
zero so that the subsequent call to pccard_validate_cis() does
not fail.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Same issues as SD card detection: One of both is always triggering and the
handlers take care to shut it up and enable the other. To avoid messages
about "unbalanced interrupt enable/disable" they must not be automatically
enabled when initally requested.
This was not an issue with the db1200_defconfig due to fortunate timings;
on a build without network chip support the warnings appear.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1133/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Prevent PCMCIA_DEV_ID_MATCH_FUNC_ID from grabbing PFC-cards:
I changed the code, so that the first matching struct
pcmcia_device_id _PFC_ entry will mark the card has_pfc,
preventing PCMCIA_DEV_ID_MATCH_FUNC_ID to match.
[linux-pcmcia@lists.infradead.org: re-order commit message]
Signed-off-by: Alexander Kurz <linux@kbdbabel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
pcmcia_dev_present is in and by itself buggy. Add a note specifying
why it is broken, and replace the broken locking -- taking a mutex
is a bad idea in IRQ context, from which this function is rarely
called -- by an atomic_t.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Use local_irq_restore in this error-handling case just like in the one just
below.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E1;
identifier f;
@@
f (...) { <+...
* local_irq_save (E1,...);
... when != E1
* return ...;
...+> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
pccard_validate_cis() nowadays destroys the CIS cache. Therefore,
calling it after card setup should be avoided. We can't control
the deprecated PCMCIA ioctl (which is only used on ARM nowadays),
but we can avoid -- and report -- any other calls.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Size needs to be calculated after manipulating with the start value.
Reported-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
If there are changes to the number of socket devices, we need to
start over in all cases: else pcmcia_request_configuration() might
get confused.
Reported-by: Alexander Kurz <linux@kbdbabel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Similar to commit 7a96e87d, we need to be aware of any parent PCI
device when requesting IO regions, even only for testing
("probing").
Reported-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Use a previously assigned IRQ for all card functions, not only if
CONFIG_PCMCIA_PROBE is set.
Reported-by: Alexander Kurz <linux@kbdbabel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
- pcmcia_align() used a "start" variable twice. That's obviously a bad
idea.
- pcmcia_common_resource() needs the current "start" parameter being
passed, instead of res->start.
- pcmcia_common_resource() doesn't use the size and align parameters,
so get rid of those.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/PCI: truncate _CRS windows with _LEN > _MAX - _MIN + 1
x86/PCI: for host bridge address space collisions, show conflicting resource
frv/PCI: remove redundant warnings
x86/PCI: remove redundant warnings
PCI: don't say we claimed a resource if we failed
PCI quirk: Disable MSI on VIA K8T890 systems
PCI quirk: RS780/RS880: work around missing MSI initialization
PCI quirk: only apply CX700 PCI bus parking quirk if external VT6212L is present
PCI: complain about devices that seem to be broken
PCI: print resources consistently with %pR
PCI: make disabled window printk style match the enabled ones
PCI: break out primary/secondary/subordinate for readability
PCI: for address space collisions, show conflicting resource
resources: add interfaces that return conflict information
PCI: cleanup error return for pcix get and set mmrbc functions
PCI: fix access of PCI_X_CMD by pcix get and set mmrbc functions
PCI: kill off pci_register_set_vga_state() symbol export.
PCI: fix return value from pcix_get_max_mmrbc()
No functional change; just print resources in the conventional style.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Instead of requiring PCMCIA socket drivers to call various functions
during their (bus) resume and suspend functions, register an own
dev_pm_ops for this class. This fixes several suspend/resume bugs
seen on db1xxx-ss, and probably on some other socket drivers, too.
With regard to the asymmetry with only _noirq suspend, but split up
resume, please see bug 14334 and commit 9905d1b411 .
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Commit aa584ca4 broke what 6cf5be51 had already fixed: there may
be four multifunction devices, but just two pseudo-multifunction
devices per PCMCIA card.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
On x86 systems using ACPI _CRS information -- now the default for
post-2008 systems -- the PCI root bus no longer pretends to be
offering the root ioport_resource. To avoid accidentally hitting
some platform / system device, use only I/O ports >= 0x100 for
PCMCIA devices on x86.
Reported-by: Komuro <komurojun-mbn@nifty.com>
CC: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Stanse found that one error path (when alloc_skb fails) in netdev_tx
omits to unlock hw_priv->hwlock. Fix that by moving away from unlock in
each fail path. Unlock at one place instead.
Introduced in 94a819f802
(pcmcia: assert locking to struct pcmcia_device)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As the PCI irq pin of the ti1130 pcmcia bridge is not connected (at
least on some old IBM Thinkpad 760ED notebooks), the Cardbus IRQ has
to be routed to an ISA irq.
Part 3 of a series to allow the ISA irq to be used for Cardbus devices
if the socket's PCI irq is unusable.
[linux@dominikbrodowski.net: split up the original patch, commit message,
cleanup]
Signed-off-by: Jens Kuenzer <Jens.Kuenzer@fpga.homeip.net>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
cb_irq is presumed to be the same as the pci_dev's irq. This won't be
true any more as soon as we allow the ISA irq to be used for Cardbus
devices. Therefore, use the pci_dev's irq explicitely whenever we
care about it.
Part 2 of a series to allow the ISA irq to be used for Cardbus devices
if the socket's PCI irq is unusable.
[linux@dominikbrodowski.net: split up the original patch, commit message]
Signed-off-by: Jens Kuenzer <Jens.Kuenzer@fpga.homeip.net>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Instead of overwriting the I365_CSCINT register, save the old value and
merely change the bits we care about.
Part 1 of a series to allow the ISA irq to be used for Cardbus devices
if the socket's PCI irq is unusable.
[linux@dominikbrodowski.net: split up the original patch, commit message]
Signed-off-by: Jens Kuenzer <Jens.Kuenzer@fpga.homeip.net>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This reverts commit 635416ef39. The
argument passed to request_irq() only affects action->flags (IRQF_*),
but IRQ_NOAUTOEN relates to desc->status.
Reported-by: Jan Beulich <JBeulich@novell.com>
CC: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
A newly added parent resource entry for the root PCI bus, such as
40000000-ffffffff : PCI Bus #00
means that the pd6729 and i82092 drivers cannot allocate iomem as
freely as before, unless they do so as PCI devices. Therefore, set
socket->cb_dev so that rsrc_nonstatic.c does the right thing.
Reported-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
struct pcmcia_socket lock had been used before.
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (370 commits)
ARM: S3C2443: Add set_rate and round_rate calls for armdiv clock
ARM: S3C2443: Remove #if 0 for clk_mpll
ARM: S3C2443: Update notes on MPLLREF clock
ARM: S3C2443: Further clksrc-clk conversions
ARM: S3C2443: Change to using plat-samsung clksrc-clk implementation
USB: Fix s3c-hsotg build following Samsung platform header moves
ARM: S3C64XX: Reintroduce unconditional build of audio device
ARM: 5961/1: ux500: fix CLKRST addresses
ARM: 5977/1: arm: Enable backtrace printing on oops when PC is corrupted
ASoC: Fix S3C64xx IIS driver for Samsung header reorg
ARM: S3C2440: Fix plat-s3c24xx move of s3c2440/s3c2442 support
[ARM] pxa: fix typo in mxm8x10.h
[ARM] pxa/raumfeld: set GPIO drive bits for LED pins
[ARM] pxa/zeus: Add support for mcp2515 CAN bus
[ARM] pxa/zeus: Add support for onboard max6369 watchdog
[ARM] pxa/zeus: Add Eurotech as the manufacturer
[ARM] pxa/zeus: Correct the USB host initialisation flags
[ARM] pxa/zeus: Allow usage of 8250-compatible UART in uncompress
[ARM] pxa: refactor uncompress.h for non-PXA uarts
[ARM] mmp2: fix incorrect calling of chip->mask_ack() for 2nd level cascaded IRQs
...
In the future, we are going to be changing the lock type for struct
device (once we get the lockdep infrastructure properly worked out) To
make that changeover easier, and to possibly burry the lock in a
different part of struct device, let's create some functions to lock and
unlock a device so that no out-of-core code needs to be changed in the
future.
This patch creates the device_lock/unlock/trylock() functions, and
converts all in-tree users to them.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Dave Young <hidave.darkstar@gmail.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Phil Carmody <ext-phil.2.carmody@nokia.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <len.brown@intel.com>
Cc: Magnus Damm <damm@igel.co.jp>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Alex Chiang <achiang@hp.com>
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrew Patterson <andrew.patterson@hp.com>
Cc: Yu Zhao <yu.zhao@intel.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: CHENG Renquan <rqcheng@smu.edu.sg>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Frans Pop <elendil@planet.nl>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix most of the remaining CodingStyle issues in drivers/pcmcia , which
related to wrong indent -- PCMCIA historically used 4 spaces. Also, remove
a custom min() implementation with the generic one.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Commit 11b897cf84 changed expected
pcmcia area addresses from the 32bit pseudo to the real 36bit
addresses, but did not update the comments.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Remoe the irq_list parameter from pd6729, as it can and should be set
via sysfs (and -- if available -- pcmciautils, which reads the information
from /etc/pcmcia/config.opts )
[linux@dominikbrodowski.net: updated commit message]
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Indigos are well known for distortions when running on some buggy ENE
controllers. There is a workaround in the yenta driver, but for some
reason it isn't activated on CB712. However, I own a laptop with such
chip and it seems that it also is affected - I can clearly hear occasional
cracks, especially under heavy network load, and in Windows XP the card is
completely unusable.
This simple change fixed things for me.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=15191
[linux@dominikbrodowski.net: extend it to the other ENE bridges]
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The IRQs for card detect and status change are currently hardcoded in
SA1111 PCMCIA driver, which can be actually obtained from the .irq[]
from 'struct sa1111_dev' to keep it generic.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
On Alchemy the PCMCIA area lies at the end of the chips 36bit system bus
area. Currently, addresses at the far end of the 32bit area are assumed
to belong to the PCMCIA area and fixed up to the real 36bit address before
being passed to ioremap().
A previous commit enabled 64 bit physical size for the resource datatype on
Alchemy and this allows to use the correct 36bit addresses when registering
the PCMCIA sockets.
This patch removes the 32-to-36bit address fixup and registers the Alchemy
demo board pcmcia socket with the correct 36bit physical addresses.
Tested on DB1200, with a CF card (ide-cs driver) and a 3c589 PCMCIA ethernet
card.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/994/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
New PCMCIA socket driver for all Db/Pb1xxx boards (except Pb1000),
which replaces au1000_db1x00.c and (most of) au1000_pb1x00.c.
Notable improvements:
- supports Db1000, DB/PB1100/1500/1550/1200.
- support for carddetect and statuschange IRQs.
- pcmcia socket mem/io/attr areas and irqs passed through
platform resource information.
- doesn't freeze system during card insertion/ejection like
the one it replaces.
- boardtype is automatically detected using BCSR ID register.
Run-tested on the DB1200.
Cc: Linux-PCMCIA <linux-pcmcia@lists.infradead.org>
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All Alchemy development boards have external CPLDs with a few registers
in them. They all share an identical register layout with only a few
minor differences (except the PB1000) in bit functions and base
addresses.
This patch
- adds a primitive facility to initialize and use these external
registers,
- replaces all occurrences of bcsr->xxx accesses with calls to the new
functions (the pb1200 cascade irq handling code is special).
- collects BCSR register information scattered throughout the board
headers in a central place.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently, only those mem resources are validated which are already
registered at the time the first PCMCIA card is inserted. As we can
only validate resources immediately after card insert, store
"registered" mem resources in mem_db, and only upon validation move
them to mem_db_valid. When allocationg mem resources, mem_db_valid is
then preferred to mem_db.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
No functional change; this converts loops that iterate from 0 to
PCI_BUS_NUM_RESOURCES through pci_bus resource[] table to use the
pci_bus_for_each_resource() iterator instead.
This doesn't change the way resources are stored; it merely removes
dependencies on the fact that they're in a table.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Now that we return the new resource start position, there is no
need to update "struct resource" inside the align function.
Therefore, mark the struct resource as const.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
As suggested by Linus, align functions should return the start
of a resource, not void. An update of "res->start" is no longer
necessary.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If a new interval overlaps or extends an existing interval in
add_interval(), do not fail, but extend the existing interval.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As this is the socket thread (pccardd) starting up, we do not have
anything to wait for in ds.c. Instead, wait the same amount of time
in pccardd to allow userspace to catch up and - possibly - execute
pcmcia-socket-startup.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Pavel Machek