The warning is not solely used for SDR104 anymore, but for all which
require tuning.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191203200513.1758-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The two devices next to each other are super similar, but still, let's
keep the alphanumeric sorting for easier additions later.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191203200513.1758-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As platform_get_irq() now prints an error when the interrupt does not
exist, counting interrupts by looping until failure causes the printing
of scary messages like:
renesas_sdhi_internal_dmac ee140000.sd: IRQ index 1 not found
Fix this by using the platform_irq_count() helper to avoid touching
non-existent interrupts.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit 7ff2131933.
It turns out that the above commit introduces other problems. For example,
calling pm_runtime_set_active() must not be done prior calling
pm_runtime_enable() as that makes it fail. This leads to additional
problems, such as clock enables being wrongly balanced.
Rather than fixing the problem on top, let's start over by doing a revert.
Fixes: 7ff2131933 ("mmc: tmio: move runtime PM enablement to the driver implementations")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Save set clock in mmc_host actual_clock enabling exporting it via debugfs.
This will indicate the precise SD clock in I/O settings rather than only the
sometimes misleading requested clock.
Signed-off-by: Tamás Szűcs <tszucs@protonmail.ch>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Quirks show up in new SoCs as well, so the naming should be generic.
Describe them by what they do.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Both the Renesas and Uniphier implementations perform actions which
affect runtime PM before calling into the core tmio_mmc_host_probe()
which enabled runtime PM. Move pm_runtime_enable() from the core and
tmio_mmc_host_probe() into each drivers probe() so it can be called
before any clocks or other resources are switched on.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Our HW engineers informed us that HS400 is not working on these SoC
revisions.
Fixes: 0f4e2054c9 ("mmc: renesas_sdhi: disable HS400 on H3 ES1.x and M3-W ES1.[012]")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The CBSY flag should be proper before calling tmio_mmc_host_probe()
because this function will already use write16 which checks this bit.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Mostly year updates, but one addition as well.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
R-Car Gen2 has two different SDHI incarnations in the same chip. The
older one does not support the recently introduced 32 bit register
access to the block count register. Make sure we use this feature only
after the first known version.
Thanks to the Renesas Testing team for this bug report!
Fixes: 5603731a15 ("mmc: tmio: fix access width of Block Count Register")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Phong Hoang <phong.hoang.wz@renesas.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SCC is used for SDR104/HS200/HS400. We need to change SCC_DT2FF
according to the mode. If it is inappropriate, CRC error tends to occur.
This adds variable "tap_hs400" for HS400 mode and configures SCC_DT2FF
as needed.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: rebased to upstream and updated commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This fixes card initialization failure in high speed mode.
If U-Boot uses SDR or HS200/400 mode before starting Linux and Linux
DT does not enable SDR/HS200/HS400 mode, card initialization fails in
high speed mode.
It is necessary to initialize SCC registers during card initialization
phase. HW reset function is registered only for a port with either of
SDR/HS200/HS400 properties in device tree. If SDR/HS200/HS400 properties
are not present in device tree, SCC registers will not be reset. In SoC
that support SCC registers, HW reset function should be registered
regardless of the configuration of device tree.
Reproduction procedure:
- Use U-Boot that support MMC HS200/400 mode.
- Delete HS200/HS400 properties in device tree.
(Delete mmc-hs200-1_8v and mmc-hs400-1_8v)
- MMC port works high speed mode and all commands fail.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Cc: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some variants (namely Renesas SDHI) have bits in the STATS and IRQ_MASK
registers which are 'always 1' and should be written as such. Introduce
a seperate mask for this and apply it whenever such a register is
written.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Renesas BSP confirms that H3 ES1.x and M3-W ES1.[012] do not
properly support HS400. Add a quirk to indicate this and disable HS400
in the MMC capabilities if the quirk is set.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Latest datasheet makes it clear that not all ES revisions of the H3 and
M3-W have the 4-tap HS400 mode quirk, currently the quirk is set
unconditionally for these two SoCs. Prepare to handle the quirk based on
SoC revision instead of compatibility value by using soc_device_match()
and set the TMIO_MMC_HAVE_4TAP_HS400 flag explicitly.
The reason for adding a new quirks struct instead of just a flag is that
looking ahead it seems more quirks needs to be handled in a SoC revision
basis.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The initial value of the interrupt mask register may be different from
the H/W manual at the startup of the kernel by setting from the
bootloader. Since the error interrupts may be unmasked, the driver sets
initial value.
The initial value is only known for R-Car Gen2 and Gen3 platforms so
limit the initialization to those platforms.
Based on work from Masaharu Hayakawa.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver sets an incorrect clock and depends on the clock driver
knowledge of this incorrect setting to still set a 200Mhz SDn clock.
Instead of spreading the workaround between the two drivers the clock
driver should be made aware of the ES versions where the special clock
handling is needed no need to keep this workaround in the SDHI driver.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
renesas_sdhi_clk_start() and renesas_sdhi_clk_stop() are now only
called from renesas_sdhi_set_clock(). Merge them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
tmio_mmc_set_clock() is full of quirks because different SoC vendors
extended this in different ways.
The original IP defines the divisor range 1/2 ... 1/512.
bit 7 is set: 1/512
bit 6 is set: 1/256
...
bit 0 is set: 1/4
all bits clear: 1/2
It is platform-dependent how to achieve the 1/1 clock.
I guess the TMIO-MFD variant uses the clock selector outside of this IP,
as far as I see tmio_core_mmc_clk_div() in drivers/mfd/tmio_core.c
I guess bit[7:0]=0xff is Renesas-specific extension.
Socionext (and Panasonic) uses bit 10 (CLKSEL) for 1/1. Also, newer
versions of UniPhier SoC variants use bit 16 for 1/1024.
host->clk_update() is only used by the Renesas variants, whereas
host->set_clk_div() is only used by the TMIO-MFD variants.
To cope with this mess, promote tmio_mmc_set_clock() to a new
platform hook ->set_clock(), and melt the old two hooks into it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When tuning each tap is issued CMD19 twice and the result of both runs
recorded in host->taps. If the result is different between the two runs
the wrong sampling clock position was selected. Fix this by merging the
two runs and only keep the result for each tap if it was good in both
sets.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit e060d376cc ("mmc: renesas_sdhi: fix WP detection")
and adds some code to really fix the regressions.
It was missed so far that Renesas R-Car instantiations of SDHI chose to
disable internal WP and used the existence of "wp-gpios" to en/disable
WP at all.
With the first refactoring by Yamada-san with commit 2ad1db059b ("mmc:
renesas_sdhi: use MMC_CAP2_NO_WRITE_PROTECT instead of TMIO own flag"),
WP was always disabled even when GPIOs were present. With Wolfram's
first fix which gets now reverted, GPIOs were honored. But when not
available, the fallback was to internal WP and not to disabled WP. This
caused wrong WP status on uSD card slots.
Restore the old behaviour now. By default, WP is disabled. When a GPIO
is found, the GPIO re-enables WP. We will think about possible better
ways to handle this in the future.
Tested on a previously regressing Renesas Lager board (H2) and a still
working Renesas Salvator-X board (M3-W).
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All our documentation says HOST_MODE, we don't really know where EXT_ACC
came from. Rename it to reduce the confusion.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers need to set up various struct members for tmio_mmc_host before
calling tmio_mmc_host_probe(). Do likewise for host->dma_ops instead
of passing it as a function argument.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The clock is enabled in the tmio_mmc_host_probe(). It also prevents
drivers from performing platform-specific settings before mmc_add_host()
because the register access generally requires a clock.
Enable/disable the clock in drivers' probe/remove. Also, I passed
tmio_mmc_data to tmio_mmc_host_alloc() because renesas_sdhi_clk_enable()
needs it to get the private data from tmio_mmc_host.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The register region is ioremap'ed in the tmio_mmc_host_probe(), i.e.
drivers cannot get access to the hardware before mmc_add_host().
Actually, renesas_sdhi_core.c reads out the CTL_VERSION register to
complete the platform-specific settings. However, at this point,
the MMC host is already running.
Move the register ioremap to tmio_mmc_host_alloc() so that drivers
can perform platform-specific settings between tmio_mmc_host_alloc()
and tmio_mmc_host_probe().
I changed tmio_mmc_host_alloc() to return an error pointer to
propagate the return code from devm_ioremap_resource().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
struct tmio_mmc_host has "scc_tappos", but in fact, it is Renesas
private data. Move it to renesas_sdhi.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
struct tmio_mmc_dma looks like TMIO core data, but in fact, Renesas
private data. Move it to renesas_sdhi.h (probably, it is better to
rename it to renesas_sdhi_dma, or squash it into struct renesas_sdhi).
I also moved struct renesas_sdhi and host_to_priv() to that header
because they are necessary to convert the tmio_mmc_host pointer into
the renesas_sdhi pointer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers can set any mmc_host_ops hooks between tmio_mmc_host_alloc()
and tmio_mmc_host_probe(). Remove duplicated hooks in tmio_mmc_host.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The remove, suspend, resume hooks need to get tmio_mmc_host. It is
tedious to call mmc_priv() to convert mmc_host to tmio_mmc_host.
We can directly set tmio_mmc_host to driver data.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The following error occurs when loading renesas_sdhi_core.c module,
so add MODULE_LICENSE("GPL v2").
renesas_sdhi_core: module license 'unspecified' taints kernel.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Fixes: 9d08428afb ("mmc: renesas-sdhi: make renesas_sdhi_sys_dmac main module file")
Cc: <stable@vger.kernel.org> # v4.13+
[Shimoda: Added Fixes tag and Cc to the stable ML]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make use of the 64 bit sdbuf width on Renesas R-Car Gen3. If the
registers are 8 byte apart, the width is also 64 bit. For all others,
the width is 32 bit, even if the registers are only 16 bit apart.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We don't use this new define yet, but it is helpful to document which
versions we know of.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Chris Brandt <Chris.Brandt@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is one SDHI instance on Gen2 which does not have the CBSY bit.
So, turn CBSY usage into an extra flag and set it accordingly. This has
the additional advantage that we can also set it for other incarnations
later.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Chris Brandt <Chris.Brandt@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Most registers need to wait until the command is completed, not
necessarily until the bus is free. At least, R-Car 2+ SoCs can signal
that via the CBSY bit, so let's use it there instead of SCLKDIVEN to
save a little bit of delay.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Allow TMIO and SDHI driver implementations to provide values for
max_segs and max_blk_count.
A follow-up patch will set these values for Renesas Gen3 SoCs
the using an SDHI driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Update copyrights to reflect work by Wolfram Sang and myself since last
year.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is 'R-Car', not 'RCar'. No code or binding changes, only descriptive text.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make renesas_sdhi_sys_dmac.c a top-level module file that makes use of
library code supplied by renesas_sdhi_core.c
This is in order to facilitate adding other variants of SDHI;
in particular SDHI using different DMA controllers.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[Arnd: Fixed module build error]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rename the source file SDHI. A follow-up patch will make it a library
file used by a different top-level module file.
The name "renesas" is chosen as the SDHI driver is applicable to a wider
range of SoCs than SH-Mobile it seems to be a more appropriate name.
However, the SDHI driver source itself, is left as sh_mobile_sdhi to
avoid unnecessary churn.
the name "core" was chosen to reflect the desired role of this file,
to provide core functionality to the sdhi driver. A follow-up patch will
move the file into that role.
Internal symbols have also been renamed to reflect the filename change.
The .name member of struct platform_driver and parameter to
MODULE_ALIAS() have not been changed in order to avoid the complication
of potentially breaking SH SoCs which still use platform drivers.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Wolfram Sang