MPLS labels may contain traffic control information, which should be
evaluated and used by the wireless subsystem if present.
Also check for IEEE 802.21 which is always network control traffic.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of my pet coding style peeves is the practice of
adding extra return; at the end of function.
Kill several instances of this in network code.
I suppose some coccinelle wizardy could do this automatically.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the previous commit, when a scan finishes, it is in theory
possible to hit the following sequence:
1. interface starts being removed
2. scan is cancelled by driver and cfg80211 is notified
3. scan done work is scheduled
4. interface is removed completely, rdev->scan_req is freed,
event sent to userspace but scan done work remains pending
5. new scan is requested on another virtual interface
6. scan done work runs, freeing the still-running scan
To fix this situation, hang on to the scan done message and block
new scans while that is the case, and only send the message from
the work function, regardless of whether the scan_req is already
freed from interface removal. This makes step 5 above impossible
and changes step 6 to be
5. scan done work runs, sending the scan done message
As this can't work for wext, so we send the message immediately,
but this shouldn't be an issue since we still return -EBUSY.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an interface/wdev is removed, any ongoing scan should be
cancelled by the driver. This will make it call cfg80211, which
only queues a work struct. If interface/wdev removal is quick
enough, this can leave the scan request pending and processed
only after the interface is gone, causing a use-after-free.
Fix this by making sure the scan request is not pending after
the interface is destroyed. We can't flush or cancel the work
item due to locking concerns, but when it'll run it shouldn't
find anything to do. This leaves a potential issue, if a new
scan gets requested before the work runs, it prematurely stops
the running scan, potentially causing another crash. I'll fix
that in the next patch.
This was particularly observed with P2P_DEVICE wdevs, likely
because freeing them is quicker than freeing netdevs.
Reported-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Fixes: 4a58e7c384 ("cfg80211: don't "leak" uncompleted scans")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Unfortunately I forgot this during the merge window, but the
patch seems small enough to go in as a fix. The userspace API
bug that was the reason for disabling it has long been fixed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the netlink skb is exhausted split_start is left set. In the
subsequent retry, with a larger buffer, the dump is continued from the
failing point instead of from the beginning.
This was causing my rt28xx based USB dongle to now show up when
running "iw list" with an old iw version without split dump support.
Cc: stable@vger.kernel.org
Fixes: 3713b4e364 ("nl80211: allow splitting wiphy information in dumps")
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
[avoid the entire workaround when state->split is set]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case we will get regulatory request with rule
where max_bandwidth_khz is set to 0 handle this
case as a special one.
If max_bandwidth_khz == 0 we should calculate maximum
available bandwidth base on all frequency contiguous rules.
In case we need auto calculation we just have to set:
country PL: DFS-ETSI
(2402 - 2482 @ 40), (N/A, 20)
(5170 - 5250 @ AUTO), (N/A, 20)
(5250 - 5330 @ AUTO), (N/A, 20), DFS
(5490 - 5710 @ 80), (N/A, 27), DFS
This mean we will calculate maximum bw for rules where
AUTO (N/A) were set, 160MHz (5330 - 5170) in example above.
So we will get:
(5170 - 5250 @ 160), (N/A, 20)
(5250 - 5330 @ 160), (N/A, 20), DFS
In other case:
country FR: DFS-ETSI
(2402 - 2482 @ 40), (N/A, 20)
(5170 - 5250 @ AUTO), (N/A, 20)
(5250 - 5330 @ 80), (N/A, 20), DFS
(5490 - 5710 @ 80), (N/A, 27), DFS
We will get 80MHz (5250 - 5170):
(5170 - 5250 @ 80), (N/A, 20)
(5250 - 5330 @ 80), (N/A, 20), DFS
Base on this calculations we will set correct channel
bandwidth flags (eg. IEEE80211_CHAN_NO_80MHZ).
We don't need any changes in CRDA or internal regulatory.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[extend nl80211 description a bit, fix typo]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It was possible to break interface combinations in
the following way:
combo 1: iftype = AP, num_ifaces = 2, num_chans = 2,
combo 2: iftype = AP, num_ifaces = 1, num_chans = 1, radar = HT20
With the above interface combinations it was
possible to:
step 1. start AP on DFS channel by matching combo 2
step 2. start AP on non-DFS channel by matching combo 1
This was possible beacuse (step 2) did not consider
if other interfaces require radar detection.
The patch changes how cfg80211 tracks channels -
instead of channel itself now a complete chandef
is stored.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When receiving an IBSS_JOINED event select the BSS object
based on the {bssid, channel} couple rather than the bssid
only.
With the current approach if another cell having the same
BSSID (but using a different channel) exists then cfg80211
picks up the wrong BSS object.
The result is a mismatching channel configuration between
cfg80211 and the driver, that can lead to any sort of
problem.
The issue can be triggered by having an IBSS sitting on
given channel and then asking the driver to create a new
cell using the same BSSID but with a different frequency.
By passing the channel to cfg80211_get_bss() we can solve
this ambiguity and retrieve/create the correct BSS object.
All the users of cfg80211_ibss_joined() have been changed
accordingly.
Moreover WARN when cfg80211_ibss_joined() gets a NULL
channel as argument and remove a bogus call of the same
function in ath6kl (it does not make sense to call
cfg80211_ibss_joined() with a zero BSSID on ibss-leave).
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Cc: libertas-dev@lists.infradead.org
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
[minor code cleanup in ath6kl]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For better use of CPU idle time, allow the scheduler to select the CPU
on which the timeout work of regulatory settings would be executed.
This extends CPU idle residency time and saves power.
This functionality is enabled when CONFIG_WQ_POWER_EFFICIENT is selected.
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Shaibal Dutta <shaibal.dutta@broadcom.com>
[zoran.markovic@linaro.org: Rebased to latest kernel. Added commit message.]
Signed-off-by: Zoran Markovic <zoran.markovic@linaro.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add helper function that will return regdomain.
Follow the driver's regulatory domain, if present,
unless a country IE has been processed or a user
wants to help compliance further.
Signed-off-by: Janusz Dziedzic <janusz.dziedzi@tieto.com>
[remove useless reg variable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set preset_chandef in channel switch notification.
In other case we will have old preset_chandef.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The scheduled scan matchsets were intended to be a list of filters,
with the found BSS having to pass at least one of them to be passed
to the host. When the RSSI attribute was added, however, this was
broken and currently wpa_supplicant adds that attribute in its own
matchset; however, it doesn't intend that to mean that anything
that passes the RSSI filter should be passed to the host, instead
it wants it to mean that everything needs to also have higher RSSI.
This is semantically problematic because we have a list of filters
like [ SSID1, SSID2, SSID3, RSSI ] with no real indication which
one should be OR'ed and which one AND'ed.
To fix this, move the RSSI filter attribute into each matchset. As
we need to stay backward compatible, treat a matchset with only the
RSSI attribute as a "default RSSI filter" for all other matchsets,
but only if there are other matchsets (an RSSI-only matchset by
itself is still desirable.)
To make driver implementation easier, keep a global min_rssi_thold
for the entire request as well. The only affected driver is ath6kl.
I found this when I looked into the code after Raja Mani submitted
a patch fixing the n_match_sets calculation to disregard the RSSI,
but that patch didn't address the semantic issue.
Reported-by: Raja Mani <rmani@qti.qualcomm.com>
Acked-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few cases, e.g. suspend, where an AP interface is
stopped by the kernel rather than by userspace request, most
commonly when suspending. To let userspace know about this,
send the NL80211_CMD_STOP_AP command as an event every time
an AP interface is stopped. This also happens when userspace
did in fact request the AP stop, but that's not a problem.
For full-MAC drivers this may need to be extended to also
cover cases where the device stopped the AP operation for
some reason, this a bit more complicated because then all
cfg80211 state also needs to be reset; such API is not part
of this patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there's a policy, then nla_parse() return values must be
checked, otherwise the policy is useless and there's nothing
that ensures the attributes are actually what we expect them
to be.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Before allowing userspace to initiate a channel switch, check
that it's actually connected in some sense. Also use a more
appropriate error code for the not connected case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix the following issues in reg_process_hint():
1. Add verification that wiphy is valid before processing
NL80211_REGDOMAIN_SET_BY_COUNTRY_IE.
2. Free the request in case of invalid initiator.
3. Remove WARN_ON check on reg_request->alpha2 as it is not a
pointer.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow to force SGI, LGI.
Mainly for test purpose.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Addition of the frequency hints showed up couple of places in cfg80211
where pointers could be marked const and a shared function could be used
to fetch a valid channel.
Signed-off-by: Jouni Malinen <j@w1.fi>
[fix mwifiex]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows drivers to advertise the maximum number of associated
stations they support in AP mode (including P2P GO). User space
applications can use this for cleaner way of handling the limit (e.g.,
hostapd rejecting IEEE 802.11 authentication without manual
configuration of the limit) or to figure out what type of use cases can
be executed with multiple devices before trying and failing.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This clarifies the expected driver behavior on the older
NL80211_ATTR_MAC and NL80211_ATTR_WIPHY_FREQ attributes and adds a new
set of similar attributes with _HINT postfix to enable use of a
recommendation of the initial BSS to choose. This can be helpful for
some drivers that can avoid an additional full scan on connection
request if the information is provided to them (user space tools like
wpa_supplicant already has that information available based on earlier
scans).
In addition, this can be used to get more expected behavior for cases
where a specific BSS should be picked first based on operations like
Interworking network selection or WPS. These cases were already easily
addressed with drivers that leave BSS selection to user space, but there
was no convenient way to do this with drivers that take care of BSS
selection internally without using the NL80211_ATTR_MAC which is not
really desired since it is needed for other purposes to force the
association to remain with the same BSS.
Signed-off-by: Jouni Malinen <j@w1.fi>
[add const, fix policy]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As __cfg80211_rdev_from_attrs(), nl80211_dump_wiphy_parse() and
nl80211_set_wiphy() are all under rtnl_lock protection,
__dev_get_by_index() instead of dev_get_by_index() should be used
to find interface handler in them allowing us to avoid to change
interface reference counter.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The REGULATORY_CUSTOM_REG can be used during early init with
the goal of overriding the wiphy's default regulatory settings
in case the alpha2 of the device is not known. In the case that
the alpha2 becomes known lets avoid having drivers having to
clear the REGULATORY_CUSTOM_REG flag by doing it for them
when regulatory_hint() is used.
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Block setting the wrong values through iwconfig retry
command. Add sanity checking before sending the retry
limit to the driver.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a utility function to get the number of channels supported by
the device, and update the places in the code that need this data.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
[replace another occurrence in libertas, fix kernel-doc, fix bugs]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While getting the retry limit, wext-compat returns the value
without updating the flag for retry->flags is 0. Also in this
case, it updates long retry flag when short and long retry
value are unequal.
So, iwconfig never showing "Retry short limit" and showing
"Retry long limit" when both values are unequal.
Updated the flags and corrected the condition properly.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The vendor/testmode event skb functions are needed outside
the ifdef for vendor-specific events, so move them out.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the RTNL can't always be held, use wdev/sdata locking for
the qos-map dereference in mac80211. This requires cfg80211 to
consistently lock it, which it was missing in one place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows QoS mapping from external networks to be implemented as
defined in IEEE Std 802.11-2012, 10.24.9. APs can use this to advertise
DSCP ranges and exceptions for mapping frames to a specific UP over
Wi-Fi.
The payload of the QoS Map Set element (IEEE Std 802.11-2012, 8.4.2.97)
is sent to the driver through the new NL80211_ATTR_QOS_MAP attribute to
configure the local behavior either on the AP (based on local
configuration) or on a station (based on information received from the
AP).
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In addition to vendor-specific commands, also support vendor-specific
events. These must be registered with cfg80211 before they can be used.
They're also advertised in nl80211 in the wiphy information so that
userspace knows can be expected. The events themselves are sent on a
new multicast group called "vendor".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add VHT MCS/NSS set support for nl80211_set_tx_bitrate_mask().
This should be used mainly for test purpose, to check
different MCS/NSS VHT combinations.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Evan Huus found (by fuzzing in wireshark) that the radiotap
iterator code can access beyond the length of the buffer if
the first bitmap claims an extension but then there's no
data at all. Fix this.
Cc: stable@vger.kernel.org
Reported-by: Evan Huus <eapache@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
___cfg80211_scan_done() can be called in some cases
(e.g. on NETDEV_DOWN) before the low level driver
notified scan completion (which is indicated by
passing leak=true).
Clearing rdev->scan_req in this case is buggy, as
scan_done_wk might have already being queued/running
(and can't be flushed as it takes rtnl()).
If a new scan will be requested at this stage, the
scan_done_wk will try freeing it (instead of the
previous scan), and this will later result in
a use after free.
Simply remove the "leak" option, and replace it with
a standard WARN_ON.
An example backtrace after such crash:
Unable to handle kernel paging request at virtual address fffffee5
pgd = c0004000
[fffffee5] *pgd=9fdf6821, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] SMP ARM
PC is at cfg80211_scan_done+0x28/0xc4 [cfg80211]
LR is at __ieee80211_scan_completed+0xe4/0x2dc [mac80211]
[<bf0077b0>] (cfg80211_scan_done+0x28/0xc4 [cfg80211])
[<bf0973d4>] (__ieee80211_scan_completed+0xe4/0x2dc [mac80211])
[<bf0982cc>] (ieee80211_scan_work+0x94/0x4f0 [mac80211])
[<c005fd10>] (process_one_work+0x1b0/0x4a8)
[<c0060404>] (worker_thread+0x138/0x37c)
[<c0066d70>] (kthread+0xa4/0xb0)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_leave stops sched scan when any station vif
is leaving. Add an explicit check and call it only
when the relevant vif (the one we scan on) is leaving.
Signed-off-by: Barak Bercovitz <barak@wizery.com>
[Eliad - changed the commit message a bit]
Signed-off-by: Eliad Peller <eliad@wizery.com>
[Johannes - add ASSERT_RTNL since that protects the pointer]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rename NL80211_TXRATE_MCS to NL80211_TXRATE_HT and also
rename mcs to ht_mcs in struct cfg80211_bitrate_mask.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow setting the bitrate masks back to default by
omitting the NL80211_ATTR_TX_RATES attribute.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[rephrase commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211 allows re-association in managed mode and if a user
wants to re-associate to the same AP network after the time
period of IEEE80211_SCAN_RESULT_EXPIRE, cfg80211 warns with
the following message on receiving the connect result event.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 13984 at net/wireless/sme.c:658
__cfg80211_connect_result+0x3a6/0x3e0 [cfg80211]()
Call Trace:
[<ffffffff81747a41>] dump_stack+0x46/0x58
[<ffffffff81045847>] warn_slowpath_common+0x87/0xb0
[<ffffffff81045885>] warn_slowpath_null+0x15/0x20
[<ffffffffa05345f6>] __cfg80211_connect_result+0x3a6/0x3e0 [cfg80211]
[<ffffffff8107168b>] ? update_rq_clock+0x2b/0x50
[<ffffffff81078c01>] ? update_curr+0x1/0x160
[<ffffffffa05133d2>] cfg80211_process_wdev_events+0xb2/0x1c0 [cfg80211]
[<ffffffff81079303>] ? pick_next_task_fair+0x63/0x170
[<ffffffffa0513518>] cfg80211_process_rdev_events+0x38/0x90 [cfg80211]
[<ffffffffa050f03d>] cfg80211_event_work+0x1d/0x30 [cfg80211]
[<ffffffff8105f21f>] process_one_work+0x17f/0x420
[<ffffffff8105f90a>] worker_thread+0x11a/0x370
[<ffffffff8105f7f0>] ? rescuer_thread+0x2f0/0x2f0
[<ffffffff8106638b>] kthread+0xbb/0xc0
[<ffffffff810662d0>] ? kthread_create_on_node+0x120/0x120
[<ffffffff817574bc>] ret_from_fork+0x7c/0xb0
[<ffffffff810662d0>] ? kthread_create_on_node+0x120/0x120
---[ end trace 61f3bddc9c4981f7 ]---
The reason is that, in connect result event cfg80211 unholds
the BSS to which the device is associated (and was held so
far). So, for the event with status successful, when cfg80211
wants to get that BSS from the device's BSS list it gets a
NULL BSS because the BSS has been expired and unheld already.
Fix it by reshuffling the code.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This permits the use of DFS channel once the CAC is conducted and
no radar is detected.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for vendor-specific commands to nl80211. This is
intended to be used for really vendor-specific functionality
that can't be implemented in a generic fashion for any reason.
It's *NOT* intended to be used for any normal/generic feature
or any optimisations that could be implemented across drivers.
Currently, only vendor commands (with replies) are supported,
no dump operations or vendor-specific notifications.
Also add a function wdev_to_ieee80211_vif() to mac80211 which
is needed for mac80211-based drivers wanting to implement any
vendor commands.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Don't clear cfg80211_bitrate_mask twice in
nl80211_set_tx_bitrate_mask() function.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Check the DFS region before channel availability check.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Simon Wunderlich