When initially probing the SPI slave device, the call for disabling an
SPI device without the SPI_CS_HIGH flag is not applied, as the
condition for checking whether or not the state to be applied equals the
one currently set evaluates to true.
This however might not necessarily be the case, as the chipselect might
be active.
Add a force flag to spi_set_cs which allows to override this
early exit condition. Set it to false everywhere except when called
from spi_setup to sync up the initial CS state.
Fixes commit d40f0b6f2e ("spi: Avoid setting the chip select if we don't
need to")
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://lore.kernel.org/r/20210416195956.121811-1-mail@david-bauer.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Add stm32_qspi_dirmap_read() and stm32_qspi_dirmap_create()
to get dirmap support.
Update the exec_op callback which doens't allow anymore memory map
access. Memory map access are only available through the dirmap_read
callback.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20210419121541.11617-4-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to optimize accesses to spi flashes, trigger a DMA only
if more than 4 bytes has to be transferred.
DMA transfer preparation's cost becomes negligible above 4 bytes to
transfer. Below this threshold, indirect transfer give more throughput.
mtd_speedtest shows that page write throughtput increases :
- from 779 to 853 KiB/s (~9.5%) with s25fl512s SPI-NOR.
- from 5283 to 5666 KiB/s (~7.25%) with Micron SPI-NAND.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20210419121541.11617-3-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime usage_count counter is not well managed.
pm_runtime_put_autosuspend callback drops the usage_counter but this
one has never been increased. Add pm_runtime_get_sync callback to bump up
the usage counter. It is also needed to use pm_runtime_force_suspend and
pm_runtime_force_resume APIs to handle properly the clock.
Fixes: 9d282c17b0 ("spi: stm32-qspi: Add pm_runtime support")
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210419121541.11617-2-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi controller supports 44-bit address space on AXI in DMA mode,
so set dma_addr_t width to 44-bit to avoid using a swiotlb mapping.
In addition, if dma_map_single fails, it should return immediately
instead of continuing doing the DMA operation which bases on invalid
address.
This fixes the following crash which occurs in reading a big block
from flash:
[ 123.633577] zynqmp-qspi ff0f0000.spi: swiotlb buffer is full (sz: 4194304 bytes), total 32768 (slots), used 0 (slots)
[ 123.644230] zynqmp-qspi ff0f0000.spi: ERR:rxdma:memory not mapped
[ 123.784625] Unable to handle kernel paging request at virtual address 00000000003fffc0
[ 123.792536] Mem abort info:
[ 123.795313] ESR = 0x96000145
[ 123.798351] EC = 0x25: DABT (current EL), IL = 32 bits
[ 123.803655] SET = 0, FnV = 0
[ 123.806693] EA = 0, S1PTW = 0
[ 123.809818] Data abort info:
[ 123.812683] ISV = 0, ISS = 0x00000145
[ 123.816503] CM = 1, WnR = 1
[ 123.819455] user pgtable: 4k pages, 48-bit VAs, pgdp=0000000805047000
[ 123.825887] [00000000003fffc0] pgd=0000000803b45003, p4d=0000000803b45003, pud=0000000000000000
[ 123.834586] Internal error: Oops: 96000145 [#1] PREEMPT SMP
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-6-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When handling op->addr, it is using the buffer "tmpbuf" which has been
freed. This will trigger a use-after-free KASAN warning. Let's use
temporary variables to store op->addr.val and op->cmd.opcode to fix
this issue.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-5-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
During a transfer the driver filled the fifo with 4bytes,
even if the data that needs to be transfer is less that 4bytes.
This resulted in slab-out-of-bounds bug in KernelAddressSanitizer.
This patch resolves slab-out-of-bounds bug by filling the fifo
with the number of bytes that needs to transferred.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-4-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After calling platform_set_drvdata(pdev, xqspi) in probe, the return
value of dev_get_drvdata(dev) is a pointer to struct zynqmp_qspi but
not struct spi_controller. A wrong structure type passing to the
functions spi_controller_suspend/resume will hang the system.
And we should check the return value of spi_controller_suspend, if
an error is returned, return it to PM subsystem to stop suspend.
Also, GQSPI_EN_MASK should be written to GQSPI_EN_OFST to enable
the spi controller in zynqmp_qspi_resume since it was disabled in
zynqmp_qspi_suspend before.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-3-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The clks "pclk" and "ref_clk" are enabled twice during the probe. The
first time is in the function zynqmp_qspi_probe and the second time is
in zynqmp_qspi_setup_op which is called by devm_spi_register_controller.
Then calling zynqmp_qspi_remove (rmmod this module) to disable these clks
will trigger a warning as below:
[ 309.124604] Unpreparing enabled qspi_ref
[ 309.128641] WARNING: CPU: 1 PID: 537 at drivers/clk/clk.c:824 clk_core_unprepare+0x108/0x110
Since pm_runtime works now, clks can be enabled/disabled by calling
zynqmp_runtime_suspend/resume. So we don't need to enable these clks
explicitly in zynqmp_qspi_setup_op. Remove them to fix this issue.
And remove clk enabling/disabling in zynqmp_qspi_resume because there is
no spi transfer operation so enabling ref_clk is redundant meanwhile pclk
is not disabled for it is shared with other peripherals.
Furthermore replace clk_enable/disable with clk_prepare_enable and
clk_disable_unprepare in runtime_suspend/resume functions.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-2-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a PM usage counter decrement after zynqmp_qspi_init_hw()
without any refcount increment, which leads to refcount leak.Add
a refcount increment to balance the refcount. Also set
auto_runtime_pm to resume suspended spi controller.
Fixes: 9e3a000362 ("spi: zynqmp: Add pm runtime support")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Tested-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210415074644.24646-1-dinghao.liu@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
The match data (struct s3c64xx_spi_port_config) stored in of_device_id
and platform_device_id tables is not modified by the driver and can be
handled entirely in a const-way to increase the code safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Link: https://lore.kernel.org/r/20210414203343.203119-3-krzysztof.kozlowski@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct the name of s3c64xx_spi_port_config structure in kerneldoc:
drivers/spi/spi-s3c64xx.c:154: warning:
expecting prototype for struct s3c64xx_spi_info. Prototype was for struct s3c64xx_spi_port_config instead
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Link: https://lore.kernel.org/r/20210414203343.203119-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use of_device_get_match_data() to make the code slightly smaller and to
remove the of_device_id table forward declaration.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Link: https://lore.kernel.org/r/20210414203343.203119-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This series fix a potential interrupt race condition and
cleanup the ACPI protection for the driver.
Change since v1:
- reword the commit in patch #2
Link: https://lore.kernel.org/linux-spi/1617881505-51552-1-git-send-email-yangyicong@hisilicon.com/
Yicong Yang (2):
spi: hisi-sfc-v3xx: fix potential irq race condition
spi: hisi-sfc-v3xx: drop unnecessary ACPI_PTR and related ifendif
protection
drivers/spi/spi-hisi-sfc-v3xx.c | 7 +++----
1 file changed, 3 insertions(+), 4 deletions(-)
--
2.8.1
Add the missing unlock before return from function zynqmp_qspi_exec_op()
in the error handling case.
Fixes: a0f65be6e8 ("spi: spi-zynqmp-gqspi: add mutex locking for exec_op")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210412160025.194171-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We use ACPI_PTR() and related ifendif protection for the id table.
This is unnecessary as the struct acpi_device_id is defined in
mod_devicetable.h and doesn't rely on ACPI. The driver doesn't
use any ACPI apis, so it can be compiled in the ACPI=n case
with no warnings.
So remove the ACPI_PTR and related ifendif protection, also
replace the header acpi.h with mod_devicetable.h.
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/1618228708-37949-3-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We mask the irq when the command completion is timeout. This won't
stop the already running irq handler. Use sychronize_irq() after
we mask the irq, to make sure there is no running handler.
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/1618228708-37949-2-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull OPP (Operating Performance Points) framework updates for v5.13
from Viresh Kumar:
"This adds devm variants for OPP APIs and updates few of the users
as well (Yangtao Li and Dmitry Osipenko)."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
memory: samsung: exynos5422-dmc: Convert to use resource-managed OPP API
drm/panfrost: Convert to use resource-managed OPP API
drm/lima: Convert to use resource-managed OPP API
mmc: sdhci-msm: Convert to use resource-managed OPP API
spi: spi-qcom-qspi: Convert to use resource-managed OPP API
spi: spi-geni-qcom: Convert to use resource-managed OPP API
serial: qcom_geni_serial: Convert to use resource-managed OPP API
opp: Change return type of devm_pm_opp_attach_genpd()
opp: Change return type of devm_pm_opp_register_set_opp_helper()
opp: Add devres wrapper for dev_pm_opp_of_add_table
opp: Add devres wrapper for dev_pm_opp_set_supported_hw
opp: Add devres wrapper for dev_pm_opp_set_regulators
opp: Add devres wrapper for dev_pm_opp_set_clkname
Quanyang Wang <quanyang.wang@windriver.com>:
From: Quanyang Wang <quanyang.wang@windriver.com>
Hello,
This series fix some issues that occurs when the gqspi driver switches to spi-mem framework.
Hi Amit,
I rewrite the "Subject" and "commit message" of these patches, so they
look different from the ones which you reviewed before. I still keep
your "Reviewed-by" and hope you will not mind.
Regards,
Quanyang Wang
Quanyang Wang (4):
spi: spi-zynqmp-gqspi: use wait_for_completion_timeout to make
zynqmp_qspi_exec_op not interruptible
spi: spi-zynqmp-gqspi: add mutex locking for exec_op
spi: spi-zynqmp-gqspi: transmit dummy circles by using the
controller's internal functionality
spi: spi-zynqmp-gqspi: fix incorrect operating mode in
zynqmp_qspi_read_op
drivers/spi/spi-zynqmp-gqspi.c | 53 +++++++++++++++++-----------------
1 file changed, 27 insertions(+), 26 deletions(-)
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Li <wangli74@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210409095458.29921-1-wangli74@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If device_get_match_data returns NULL, devdata isn't being updated
properly. It is being used later in the function. Both devdata and
spi->devdata should be updated to avoid NULL pointer dereference.
Addresses-Coverity: ("NULL pointer dereference")
Fixes: 0e6521f13c ("spi: orion: Use device_get_match_data() helper")
Signed-off-by: Muhammad Usama Anjum <musamaanjum@gmail.com>
Link: https://lore.kernel.org/r/20210408195718.GA3075166@LEGION
Signed-off-by: Mark Brown <broonie@kernel.org>
When some drivers use spi to send data, spi_transfer->speed_hz is
not assigned. If spidev->max_speed_hz is not assigned as well, it
will cause an error in configuring the clock.
Add a check for these two values before configuring the clock. An
error will be returned when they are not assigned.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/r/20210408103347.244313-2-xiaoning.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Call spi_master_get() holds the reference count to master device, thus
we need an additional spi_master_put() call to reduce the reference
count, otherwise we will leak a reference to master.
This commit fix it by removing the unnecessary spi_master_get().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210409082954.2906933-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Fixes: 944c01a889 ("spi: lpspi: enable runtime pm for lpspi")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Li <wangli74@huawei.com>
Link: https://lore.kernel.org/r/20210409095430.29868-1-wangli74@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_add_action_or_reset() instead of devres_alloc() and
devres_add(), which works the same. This will simplify the
code. There is no functional changes.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/1617843307-53853-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Call spi_master_get() holds the reference count to master device, thus
we need an additional spi_master_put() call to reduce the reference
count, otherwise we will leak a reference to master.
This commit fix it by removing the unnecessary spi_master_get().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210409082955.2907950-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When starting a read operation, we should call zynqmp_qspi_setuprxdma
first to set xqspi->mode according to xqspi->bytes_to_receive and
to calculate correct xqspi->dma_rx_bytes. Then in the function
zynqmp_qspi_fillgenfifo, generate the appropriate command with
operating mode and bytes to transfer, and fill the GENFIFO with
the command to perform the read operation.
Calling zynqmp_qspi_fillgenfifo before zynqmp_qspi_setuprxdma will
result in incorrect transfer length and operating mode. So change
the calling order to fix this issue.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210408040223.23134-5-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a data corruption issue that occurs in the reading operation
(cmd:0x6c) when transmitting common data as dummy circles.
The gqspi controller has the functionality to send dummy clock circles.
When writing data with the fields [receive, transmit, data_xfer] = [0,0,1]
to the Generic FIFO, and configuring the correct SPI mode, the controller
will transmit dummy circles.
So let's switch to hardware dummy cycles transfer to fix this issue.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210408040223.23134-4-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-mem framework has no locking to prevent ctlr->mem_ops->exec_op
from concurrency. So add the locking to zynqmp_qspi_exec_op.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210408040223.23134-3-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When Ctrl+C occurs during the process of zynqmp_qspi_exec_op, the function
wait_for_completion_interruptible_timeout will return a non-zero value
-ERESTARTSYS immediately. This will disrupt the SPI memory operation
because the data transmitting may begin before the command or address
transmitting completes. Use wait_for_completion_timeout to prevent
the process from being interruptible.
This patch fixes the error as below:
root@xilinx-zynqmp:~# flash_erase /dev/mtd3 0 0
Erasing 4 Kibyte @ 3d000 -- 4 % complete
(Press Ctrl+C)
[ 169.581911] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 170.585907] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 171.589910] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 172.593910] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 173.597907] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 173.603480] spi-nor spi0.0: Erase operation failed.
[ 173.608368] spi-nor spi0.0: Attempted to modify a protected sector.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210408040223.23134-2-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
list_sort() internally casts the comparison function passed to it
to a different type with constant struct list_head pointers, and
uses this pointer to call the functions, which trips indirect call
Control-Flow Integrity (CFI) checking.
Instead of removing the consts, this change defines the
list_cmp_func_t type and changes the comparison function types of
all list_sort() callers to use const pointers, thus avoiding type
mismatches.
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210408182843.1754385-10-samitolvanen@google.com
Add the missing iounmap() before return from of_fsl_spi_probe()
in the error handling case.
Fixes: 0f0581b24b ("spi: fsl: Convert to use CS GPIO descriptors")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210401140350.1677925-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We can't rely on the contents of the devres list during
spi_unregister_controller(), as the list is already torn down at the
time we perform devres_find() for devm_spi_release_controller. This
causes devices registered with devm_spi_alloc_{master,slave}() to be
mistakenly identified as legacy, non-devm managed devices and have their
reference counters decremented below 0.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 660 at lib/refcount.c:28 refcount_warn_saturate+0x108/0x174
[<b0396f04>] (refcount_warn_saturate) from [<b03c56a4>] (kobject_put+0x90/0x98)
[<b03c5614>] (kobject_put) from [<b0447b4c>] (put_device+0x20/0x24)
r4:b6700140
[<b0447b2c>] (put_device) from [<b07515e8>] (devm_spi_release_controller+0x3c/0x40)
[<b07515ac>] (devm_spi_release_controller) from [<b045343c>] (release_nodes+0x84/0xc4)
r5:b6700180 r4:b6700100
[<b04533b8>] (release_nodes) from [<b0454160>] (devres_release_all+0x5c/0x60)
r8:b1638c54 r7:b117ad94 r6:b1638c10 r5:b117ad94 r4:b163dc10
[<b0454104>] (devres_release_all) from [<b044e41c>] (__device_release_driver+0x144/0x1ec)
r5:b117ad94 r4:b163dc10
[<b044e2d8>] (__device_release_driver) from [<b044f70c>] (device_driver_detach+0x84/0xa0)
r9:00000000 r8:00000000 r7:b117ad94 r6:b163dc54 r5:b1638c10 r4:b163dc10
[<b044f688>] (device_driver_detach) from [<b044d274>] (unbind_store+0xe4/0xf8)
Instead, determine the devm allocation state as a flag on the
controller which is guaranteed to be stable during cleanup.
Fixes: 5e844cc37a ("spi: Introduce device-managed SPI controller allocation")
Signed-off-by: William A. Kennington III <wak@google.com>
Link: https://lore.kernel.org/r/20210407095527.2771582-1-wak@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When platform_get_irq() fails, a pairing PM usage counter
increment is needed to keep the counter balanced. It's the
same for the following error paths.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20210408092559.3824-1-dinghao.liu@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix warning Woverflow on type conversion reported on x86_64:
drivers/spi/spi-hisi-kunpeng.c:361:9: warning: conversion from 'long unsigned int' to 'u32'
{aka 'unsigned int'} changes value from '18446744073709551600' to '4294967280' [-Woverflow]
The registers are 32 bit, so fix by casting to u32.
Fixes: c770d8631e ("spi: Add HiSilicon SPI Controller Driver for Kunpeng SoCs")
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1617762660-54681-1-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver supports SPI Controller for HiSilicon Kunpeng SoCs. This
driver supports SPI operations using FIFO mode of transfer.
DMA is not supported, and we just use IRQ mode for operation completion
notification.
Only ACPI firmware is supported.
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1616836200-45827-1-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patchset tries to resolve the diversity in the audio LED
control among the ALSA drivers. A new control layer registration
is introduced which allows to run additional operations on
top of the elementary ALSA sound controls.
A new control access group (three bits in the access flags)
was introduced to carry the LED group information for
the sound controls. The low-level sound drivers can just
mark those controls using this access group. This information
is not exported to the user space, but user space can
manage the LED sound control associations through sysfs
(last patch) per Mark's request. It makes things fully
configurable in the kernel and user space (UCM).
The actual state ('route') evaluation is really easy
(the minimal value check for all channels / controls / cards).
If there's more complicated logic for a given hardware,
the card driver may eventually export a new read-only
sound control for the LED group and do the logic itself.
The new LED trigger control code is completely separated
and possibly optional (there's no symbol dependency).
The full code separation allows eventually to move this
LED trigger control to the user space in future.
Actually it replaces the already present functionality
in the kernel space (HDA drivers) and allows a quick adoption
for the recent hardware (ASoC codecs including SoundWire).
snd_ctl_led 24576 0
The sound driver implementation is really easy:
1) call snd_ctl_led_request() when control LED layer should be
automatically activated
/ it calls module_request("snd-ctl-led") on demand /
2) mark all related kcontrols with
SNDRV_CTL_ELEM_ACCESS_SPK_LED or
SNDRV_CTL_ELEM_ACCESS_MIC_LED
Link: https://lore.kernel.org/r/20210317172945.842280-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
-----BEGIN PGP SIGNATURE-----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=1uM7
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmBkoFEACgkQJNaLcl1U
h9BqTgf5AUfR5NbQgJIUMtdMsuz+bthKGuPnpYhYzNUH0io9i3Sjpt0Mbw21dLp2
nXW+70BH0tJZBGR4DNGpmcpBLH5WPdOR9WIv4vCYy9Pr0uCGGKF/JkGeZAg7/llF
C3+yDfTnF0AvR+74xbf/LTjBPGja/08PED1ZC00NAkLhE3C0Pa/VQ0NaEtPUULWE
ZOWboF7hfQUeGzGPTqNp4Cy0/Pzokk6Fvl4kgfrxjNWO7ojIv9mCAvmYbusLW7NU
3Ph5VGsIuyMeorEoAVOFaBY2nrYG/mFZyzTNWJMgvF1MdeigMPNfbbffrUK0sn6k
e81zgWbwxboEujQ91/EZU7glIqtb6A==
=rr4V
-----END PGP SIGNATURE-----
Merge tag 'mute-led-rework' of https://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound into asoc-5.13
ALSA: control - add generic LED API
This patchset tries to resolve the diversity in the audio LED
control among the ALSA drivers. A new control layer registration
is introduced which allows to run additional operations on
top of the elementary ALSA sound controls.
A new control access group (three bits in the access flags)
was introduced to carry the LED group information for
the sound controls. The low-level sound drivers can just
mark those controls using this access group. This information
is not exported to the user space, but user space can
manage the LED sound control associations through sysfs
(last patch) per Mark's request. It makes things fully
configurable in the kernel and user space (UCM).
The actual state ('route') evaluation is really easy
(the minimal value check for all channels / controls / cards).
If there's more complicated logic for a given hardware,
the card driver may eventually export a new read-only
sound control for the LED group and do the logic itself.
The new LED trigger control code is completely separated
and possibly optional (there's no symbol dependency).
The full code separation allows eventually to move this
LED trigger control to the user space in future.
Actually it replaces the already present functionality
in the kernel space (HDA drivers) and allows a quick adoption
for the recent hardware (ASoC codecs including SoundWire).
snd_ctl_led 24576 0
The sound driver implementation is really easy:
1) call snd_ctl_led_request() when control LED layer should be
automatically activated
/ it calls module_request("snd-ctl-led") on demand /
2) mark all related kcontrols with
SNDRV_CTL_ELEM_ACCESS_SPK_LED or
SNDRV_CTL_ELEM_ACCESS_MIC_LED
Link: https://lore.kernel.org/r/20210317172945.842280-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This converts the PL022 driver to use GPIO descriptors
instead of the old global GPIO numberspace. Since the
driver handles messages on its own it needs to manage
the GPIO descriptor directly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210330164907.2346010-3-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI core looks up GPIO lines from the device tree,
so let's stop trying to do that on our own and rely
on the core to do this for us.
In addition to the GPIO line we also need to keep
track of the chip select index separately, as the native
chip select needs this index. The driver was reusing
the same GPIO array for native chip select indices,
so keep this in a separate state variable instead.
The facility to pass in custom GPIO lines from the
platform data can go, because even if we do have
out-of-tree code that want to use platform data, they
can soon pass in GPIOs using machine GPIO descriptor
tables which will be available after the next step
when we convert the driver to using GPIO descriptors.
The implicit inclusion of <linux/of.h> is made
explicit as we no longer need to include <linux/of_gpio.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210330164907.2346010-2-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop the custom cs_control() assigned through platform data,
we have no in-tree users and the only out-of-tree use I have
ever seen of this facility is to pull GPIO lines, which is
something the driver can already do for us.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210330164907.2346010-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When using the device tree, which must be considered normal
these days, in order to get some kind of normal functionality
out of the PL022 users have to actively go into the device
tree and edit the SPI clients like this:
spi {
compatible = "arm,pl022";
num-cs = <1>;
cs-gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
foo@0 {
compatible = "foo";
reg = <0>;
pl022,interface = <0>;
pl022,com-mode = <0>;
};
};
Otherwise the PL022 will come up as a client (slave) and
using polling mode. This is quite unintuitive and many users
will get their device trees wrong.
Alter the defaults such that we come up in host mode
(master) and use interrupt mode.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210328121530.1983081-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
add compatible entry in nxp_fspi driver for imx8mp
@Shawn: If this series is accepted, can you apply the DTS patches from
series v2?
http://lists.infradead.org/pipermail/linux-arm-kernel/2021-March/643292.htmlhttp://lists.infradead.org/pipermail/linux-arm-kernel/2021-March/643293.html
Changes in v4:
rebased against:
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next
a43e89624baea ("Merge remote-tracking branch 'spi/for-5.13' into spi-next")
Changes in v3:
- seperate spi changes from series:
http://lists.infradead.org/pipermail/linux-arm-kernel/2021-March/643289.html
into own series as Kuldeep suggested and rebased against
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next
144c79ef33 ("Merge tag 'perf-tools-fixes-for-v5.12-2020-03-07' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux")
- no changes, rebased against
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next
144c79ef33 Merge tag 'perf-tools-fixes-for-v5.12-2020-03-07' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Changes in v2:
- work in comments from Marco
add own compatible entry for imx8mp
Heiko Schocher (2):
spi: fspi: enable fspi driver for on imx8mp
dt-bindings: spi: add compatible entry for imx8mp in FlexSPI
controller
Documentation/devicetree/bindings/spi/spi-nxp-fspi.txt | 1 +
drivers/spi/spi-nxp-fspi.c | 1 +
2 files changed, 2 insertions(+)
--
2.29.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Updated restricted chips have trouble processing multiple sequenced
operations. So remove the capability to sequence multiple operations and
reduce the maximum transfer size to 8 bytes.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210324220516.41192-1-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix checkpatch errors:
ERROR: code indent should use tabs where possible
#484: FILE: spi-rockchip.c:484:
+^I | CR0_BHT_8BIT << CR0_BHT_OFFSET$
ERROR: code indent should use tabs where possible
#485: FILE: spi-rockchip.c:485:
+^I | CR0_SSD_ONE << CR0_SSD_OFFSET$
ERROR: code indent should use tabs where possible
#486: FILE: spi-rockchip.c:486:
+^I | CR0_EM_BIG << CR0_EM_OFFSET;$
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1616566602-13894-11-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix checkpatch errors:
ERROR: code indent should use tabs where possible
#624: FILE: spi-mem.c:624:
ERROR: code indent should use tabs where possible
#626: FILE: spi-mem.c:626:
ERROR: code indent should use tabs where possible
#627: FILE: spi-mem.c:627:
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1616566602-13894-10-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix checkpatch errors:
ERROR: open brace '{' following function definitions go on the next line
#54: FILE: spi-bitbang.c:54:
ERROR: open brace '{' following function definitions go on the next line
#82: FILE: spi-bitbang.c:82:
ERROR: open brace '{' following function definitions go on the next line
#110: FILE: spi-bitbang.c:110:
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1616566602-13894-8-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix checkpatch error:
ERROR: open brace '{' following function definitions go on the next line
#545: FILE: spi-dln2.c:545:
+static int dln2_spi_rdwr(struct dln2_spi *dln2, const u8 *tx_data,
+ u8 *rx_data, u16 data_len, u8 attr) {
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1616566602-13894-7-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix checkpatch error:
ERROR: space prohibited before that close parenthesis ')'
#213: FILE: spi-sprd-adi.c:213:
+ rd_addr = (val & RD_ADDR_MASK ) >> RD_ADDR_SHIFT;
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1616566602-13894-3-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
stm32_spi_remove() accesses the driver's private data after calling
spi_unregister_master() even though that function releases the last
reference on the spi_master and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
Fixes: 8d559a64f0 ("spi: stm32: drop devres version of spi_register_master")
Reported-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/1616052290-10887-1-git-send-email-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi,
The older API used to supply additional device properties for the
devices - so mainly the function device_add_properties() - is going to
be removed. The reason why the API will be removed is because it gives
false impression that the properties are assigned directly to the
devices, which has actually never been the case - the properties have
always been assigned to a software fwnode which was then just directly
linked with the device when the old API was used. By only accepting
device properties instead of complete software nodes, the subsystems
remove any change of taking advantage of the other features the
software nodes have.
The change that is required from the spi subsystem and the drivers is
trivial. Basically only the "properties" member in struct
spi_board_info, which was a pointer to struct property_entry, is
replaced with a pointer to a complete software node.
thanks,
Heikki Krogerus (4):
spi: Add support for software nodes
ARM: pxa: icontrol: Constify the software node
ARM: pxa: zeus: Constify the software node
spi: Remove support for dangling device properties
arch/arm/mach-pxa/icontrol.c | 12 ++++++++----
arch/arm/mach-pxa/zeus.c | 6 +++++-
drivers/spi/spi.c | 21 ++++++---------------
include/linux/spi/spi.h | 7 +++----
4 files changed, 22 insertions(+), 24 deletions(-)
--
2.30.1
base-commit: a38fd87484
Making it possible for the drivers to assign complete
software fwnodes to the devices instead of only the device
properties in those nodes.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210303152814.35070-2-heikki.krogerus@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use resource-managed OPP API to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Use resource-managed OPP API to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
A while back I started the introduction of the 'spi_delay' data type:
https://lore.kernel.org/linux-spi/20190926105147.7839-1-alexandru.ardelean@analog.com/
Users of the 'delay_usecs' were removed from drivers.
Now it's time to remove the 'delay_usecs' from the SPI subsystem and use
only the 'delay' field.
This changeset adapts all SPI drivers to do without 'delay_usecs'.
Additionally, for greybus we need to adapt it to use the 'delay' in
nano-seconds and convert it to micro-seconds.
Alexandru Ardelean (10):
spi: spi-axi-spi-engine: remove usage of delay_usecs
spi: bcm63xx-spi: don't check 'delay_usecs' field
spi: spi-bcm-qspi: replace 'delay_usecs' with 'delay.value' check
spi: spi-sh: replace 'delay_usecs' with 'delay.value' in pr_debug
spi: spi-tegra20-flash: don't check 'delay_usecs' field for spi
transfer
staging: greybus: spilib: use 'spi_delay_to_ns' for getting xfer delay
spi: spi-falcon: remove check for 'delay_usecs'
spi: fsl-espi: remove usage of 'delay_usecs' field
spi: core: remove 'delay_usecs' field from spi_transfer
spi: docs: update info about 'delay_usecs'
Documentation/spi/spi-summary.rst | 7 +++++--
drivers/spi/spi-axi-spi-engine.c | 12 ++++--------
drivers/spi/spi-bcm-qspi.c | 2 +-
drivers/spi/spi-bcm63xx.c | 2 +-
drivers/spi/spi-falcon.c | 2 +-
drivers/spi/spi-fsl-espi.c | 17 +++++------------
drivers/spi/spi-sh.c | 4 ++--
drivers/spi/spi-tegra20-sflash.c | 3 +--
drivers/spi/spi.c | 1 -
drivers/staging/greybus/spilib.c | 5 ++++-
include/linux/spi/spi.h | 12 ------------
11 files changed, 24 insertions(+), 43 deletions(-)
--
2.29.2
_______________________________________________
devel mailing list
devel@linuxdriverproject.orghttp://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
The 'delay' field in the spi_transfer struct is meant to replace the
'delay_usecs' field. However some cleanup was required to remove the
uses of 'delay_usecs'. Now that it's been cleaned up, we can remove it
from the kernel tree.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210308145502.1075689-10-aardelean@deviqon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'delay_usecs' field is being removed from the spi_transfer struct.
This change removes it from the SPI FSL ESPI driver.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210308145502.1075689-9-aardelean@deviqon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'delay_usecs' field is being removed from the spi_transfer struct.
This change removes it from the SPI Falcon driver.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210308145502.1075689-8-aardelean@deviqon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'delay_usecs' field was handled for backwards compatibility in case
there were some users that still configured SPI delay transfers with
this field.
They should all be removed by now. So we can remove the 'delay_usecs'
handling in this driver.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210308145502.1075689-6-aardelean@deviqon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'delay_usecs' field is going away. The replacement for it is the
'delay' field. So, we should print the 'delay.value' value instead.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210308145502.1075689-5-aardelean@deviqon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'delay_usecs' field is going away. The replacement for it is the
'delay' field. So, we should check for 'delay.value' being non-zero.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210308145502.1075689-4-aardelean@deviqon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'delay_usecs' field was handled for backwards compatibility in case
there were some users that still configured SPI delay transfers with
this field.
They should all be removed by now.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210308145502.1075689-3-aardelean@deviqon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'delay_usecs' field was handled for backwards compatibility in case
there were some users that still configured SPI delay transfers with
this field.
They should all be removed by now.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210308145502.1075689-2-aardelean@deviqon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A call to spi_unregister_master() triggers calling remove()
for all the spi devices binded to the spi master.
Some spi device driver requires to "talk" with the spi device
during the remove(), e.g.:
- a LCD panel like drivers/gpu/drm/panel/panel-lg-lg4573.c
will turn off the backlighting sending a command over spi.
This implies that the spi master must be fully functional when
spi_unregister_master() is called, either if it is called
explicitly in the master's remove() code or implicitly by the
devres framework.
Devres calls devres_release_all() to release all the resources
"after" the remove() of the spi master driver (check code of
__device_release_driver() in drivers/base/dd.c).
If the spi master driver has an empty remove() then there would
be no issue; the devres_release_all() will release everything
in reverse order w.r.t. probe().
But if code in spi master driver remove() disables the spi or
makes it not functional (like in this spi-stm32), then devres
cannot be used safely for unregistering the spi master and the
binded spi devices.
Replace devm_spi_register_master() with spi_register_master()
and add spi_unregister_master() as first action in remove().
Fixes: dcbe0d84df ("spi: add driver for STM32 SPI controller")
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/1615545286-5395-1-git-send-email-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When initialize cadence qspi controller, it is need to set cqspi
to the driver_data field of struct device, because it will be
used in function cqspi_remove/suspend/resume(). Otherwise, there
will be a crash trace as below when invoking these finctions.
Fixes: 31fb632b5d ("spi: Move cadence-quadspi driver to drivers/spi/")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Link: https://lore.kernel.org/r/20210311091220.3615-1-Meng.Li@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/spi/spi-cadence-quadspi.c:267:18: warning: Shifting signed 32-bit
value by 31 bits is undefined behaviour [shiftTooManyBitsSigned]
return reg & (1 << CQSPI_REG_CONFIG_IDLE_LSB);
^
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1614854872-8694-1-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce module_parport_driver() and use it.
Greg or Mark, since we have this series tagged, can somebody of you pick it up?
Changelog v3:
- added tag on patch 1 (Sudip)
- Cc'ed to Greg
Andy Shevchenko (3):
parport: Introduce module_parport_driver() helper macro
spi: butterfly: Switch to use module_parport_driver()
spi: lm70llp: Switch to use module_parport_driver()
drivers/spi/spi-butterfly.c | 13 +------------
drivers/spi/spi-lm70llp.c | 13 +------------
include/linux/parport.h | 12 +++++++++++-
3 files changed, 13 insertions(+), 25 deletions(-)
base-commit: fe07bfda2f
--
2.30.1
Errata ERR050568 description says that "Flash access by FlexSPI AHB
command may not work with platform frequency equal to 300 MHz" on
LS1028A.
By default, smaller length reads(equal to RX FIFO size) are done by IP
bus and larger length reads using AHB bus. For adding errata workaround,
use IP bus to read entire flash contents and disable AHB path when
platform frequency is 300Mhz.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Link: https://lore.kernel.org/r/20210302124936.1972546-5-kuldeep.singh@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add driver support for imx8dxl which support read through IP bus only
and disable AHB bus due to an IC errata. Use the pre-defined quirk
FSPI_QUIRK_USE_IP_ONLY directly in device-type data to disable AHB read.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Link: https://lore.kernel.org/r/20210302124936.1972546-4-kuldeep.singh@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for disabling AHB bus and read entire flash contents via IP
bus only. Please note, this enables IP bus read using a quirk which can
be enabled directly in device-type data or in existence of an errata
where AHB bus may need to be disabled.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Link: https://lore.kernel.org/r/20210302124936.1972546-2-kuldeep.singh@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix OF node leaks by calling of_node_put in
for_each_available_child_of_node when the cycle returns.
Generated by: scripts/coccinelle/iterators/for_each_child.cocci
Signed-off-by: Junlin Yang <yangjunlin@yulong.com>
Link: https://lore.kernel.org/r/20210215110425.1012-1-angkery@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Building this file with clang leads to a an unreachable code path
causing a warning from objtool:
drivers/spi/spi-rockchip.o: warning: objtool: rockchip_spi_transfer_one()+0x2e0: sibling call from callable instruction with modified stack frame
Change the unreachable() into an error return that can be
handled if it ever happens, rather than silently crashing
the kernel.
Fixes: 65498c6ae2 ("spi: rockchip: support 4bit words")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210226140109.3477093-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the (optional) idle pinctrl state during runtime suspend. This is the
same schema used in PL022 driver and can help with HW designs sharing
the SPI lines for different purposes.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20210222023243.491432-1-alexander.sverdlin@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This removes the assignment of setup and cleanup functions for the ath79
target. Assigning the setup-method will lead to 'setup_transfer' not
being assigned in spi_bitbang_init. Because of this, performing any
TX/RX operation will lead to a kernel oops.
Also drop the redundant cleanup assignment, as it's also assigned in
spi_bitbang_init.
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://lore.kernel.org/r/20210303160837.165771-2-mail@david-bauer.net
Signed-off-by: Mark Brown <broonie@kernel.org>
spi-bitbang has to call the chipselect function on the ath79 SPI driver
in order to communicate with the SPI slave device, as the ath79 SPI
driver has three dedicated chipselect lines but can also be used with
GPIOs for the CS lines.
Fixes commit 4a07b8bcd5 ("spi: bitbang: Make chipselect callback optional")
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://lore.kernel.org/r/20210303160837.165771-1-mail@david-bauer.net
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver sets auto_runtime_pm to true, but it doesn't call
pm_runtime_enable(), which results in "Failed to power device" when PM support
is enabled.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://lore.kernel.org/r/20210223151851.4110-3-noltari@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver sets auto_runtime_pm to true, but it doesn't call
pm_runtime_enable(), which results in "Failed to power device" when PM support
is enabled.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://lore.kernel.org/r/20210223151851.4110-2-noltari@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A large series adding wrappers for our interrupt handlers, so that irq/nmi/user
tracking can be isolated in the wrappers rather than spread in each handler.
Conversion of the 32-bit syscall handling into C.
A series from Nick to streamline our TLB flushing when using the Radix MMU.
Switch to using queued spinlocks by default for 64-bit server CPUs.
A rework of our PCI probing so that it happens later in boot, when more generic
infrastructure is available.
Two small fixes to allow 32-bit little-endian processes to run on 64-bit
kernels.
Other smaller features, fixes & cleanups.
Thanks to:
Alexey Kardashevskiy, Ananth N Mavinakayanahalli, Aneesh Kumar K.V, Athira
Rajeev, Bhaskar Chowdhury, Cédric Le Goater, Chengyang Fan, Christophe Leroy,
Christopher M. Riedl, Fabiano Rosas, Florian Fainelli, Frederic Barrat, Ganesh
Goudar, Hari Bathini, Jiapeng Chong, Joseph J Allen, Kajol Jain, Markus
Elfring, Michal Suchanek, Nathan Lynch, Naveen N. Rao, Nicholas Piggin, Oliver
O'Halloran, Pingfan Liu, Po-Hsu Lin, Qian Cai, Ram Pai, Randy Dunlap, Sandipan
Das, Stephen Rothwell, Tyrel Datwyler, Will Springer, Yury Norov, Zheng
Yongjun.
-----BEGIN PGP SIGNATURE-----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=dB2S
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- A large series adding wrappers for our interrupt handlers, so that
irq/nmi/user tracking can be isolated in the wrappers rather than
spread in each handler.
- Conversion of the 32-bit syscall handling into C.
- A series from Nick to streamline our TLB flushing when using the
Radix MMU.
- Switch to using queued spinlocks by default for 64-bit server CPUs.
- A rework of our PCI probing so that it happens later in boot, when
more generic infrastructure is available.
- Two small fixes to allow 32-bit little-endian processes to run on
64-bit kernels.
- Other smaller features, fixes & cleanups.
Thanks to: Alexey Kardashevskiy, Ananth N Mavinakayanahalli, Aneesh
Kumar K.V, Athira Rajeev, Bhaskar Chowdhury, Cédric Le Goater, Chengyang
Fan, Christophe Leroy, Christopher M. Riedl, Fabiano Rosas, Florian
Fainelli, Frederic Barrat, Ganesh Goudar, Hari Bathini, Jiapeng Chong,
Joseph J Allen, Kajol Jain, Markus Elfring, Michal Suchanek, Nathan
Lynch, Naveen N. Rao, Nicholas Piggin, Oliver O'Halloran, Pingfan Liu,
Po-Hsu Lin, Qian Cai, Ram Pai, Randy Dunlap, Sandipan Das, Stephen
Rothwell, Tyrel Datwyler, Will Springer, Yury Norov, and Zheng Yongjun.
* tag 'powerpc-5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (188 commits)
powerpc/perf: Adds support for programming of Thresholding in P10
powerpc/pci: Remove unimplemented prototypes
powerpc/uaccess: Merge raw_copy_to_user_allowed() into raw_copy_to_user()
powerpc/uaccess: Merge __put_user_size_allowed() into __put_user_size()
powerpc/uaccess: get rid of small constant size cases in raw_copy_{to,from}_user()
powerpc/64: Fix stack trace not displaying final frame
powerpc/time: Remove get_tbl()
powerpc/time: Avoid using get_tbl()
spi: mpc52xx: Avoid using get_tbl()
powerpc/syscall: Avoid storing 'current' in another pointer
powerpc/32: Handle bookE debugging in C in syscall entry/exit
powerpc/syscall: Do not check unsupported scv vector on PPC32
powerpc/32: Remove the counter in global_dbcr0
powerpc/32: Remove verification of MSR_PR on syscall in the ASM entry
powerpc/syscall: implement system call entry/exit logic in C for PPC32
powerpc/32: Always save non volatile GPRs at syscall entry
powerpc/syscall: Change condition to check MSR_RI
powerpc/syscall: Save r3 in regs->orig_r3
powerpc/syscall: Use is_compat_task()
powerpc/syscall: Make interrupt.c buildable on PPC32
...
- Generalise byte swapping assembly
- Update debug addresses for STI
- Validate start of physical memory with DTB
- Do not clear SCTLR.nTLSMD in decompressor
- amba/locomo/sa1111 devices remove method return type is void
- address markers for KASAN in page table dump
-----BEGIN PGP SIGNATURE-----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=BULT
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- Generalise byte swapping assembly
- Update debug addresses for STI
- Validate start of physical memory with DTB
- Do not clear SCTLR.nTLSMD in decompressor
- amba/locomo/sa1111 devices remove method return type is void
- address markers for KASAN in page table dump
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9065/1: OABI compat: fix build when EPOLL is not enabled
ARM: 9055/1: mailbox: arm_mhuv2: make remove callback return void
amba: Make use of bus_type functions
amba: Make the remove callback return void
vfio: platform: simplify device removal
amba: reorder functions
amba: Fix resource leak for drivers without .remove
ARM: 9054/1: arch/arm/mm/mmu.c: Remove duplicate header
ARM: 9053/1: arm/mm/ptdump:Add address markers for KASAN regions
ARM: 9051/1: vdso: remove unneded extra-y addition
ARM: 9050/1: Kconfig: Select ARCH_HAVE_NMI_SAFE_CMPXCHG where possible
ARM: 9049/1: locomo: make locomo bus's remove callback return void
ARM: 9048/1: sa1111: make sa1111 bus's remove callback return void
ARM: 9047/1: smp: remove unused variable
ARM: 9046/1: decompressor: Do not clear SCTLR.nTLSMD for ARMv7+ cores
ARM: 9045/1: uncompress: Validate start of physical memory against passed DTB
ARM: 9042/1: debug: no uncompress debugging while semihosting
ARM: 9041/1: sti LL_UART: add STiH418 SBC UART0 support
ARM: 9040/1: use DEBUG_UART_PHYS and DEBUG_UART_VIRT for sti LL_UART
ARM: 9039/1: assembler: generalize byte swapping macro into rev_l
The main focus of this release from a framework point of view has been
spi-mem where we've acquired support for a few new hardware features
which enable better performance on suitable hardware. Otherwise mostly
thanks to Arnd's cleanup efforts on old platforms we've removed several
obsolete drivers which just about balance out the newer drivers we've
added this cycle.
- Allow drivers to flag if they are unidirectional.
- Support for DTR mode and hardware acceleration of dummy cycles in spi-mem.
- Support for Allwinder H616, Intel Lightning Mountain, nVidia Tegra
QuadSPI, Realtek RTL838x and RTL839x.
- Removal of obsolute EFM32, Txx9 and SIRF Prima and Atlas drivers.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmAq3M0ACgkQJNaLcl1U
h9Aq3gf6AuboDwFguKZAmXp27zjYsv5o5KtPyycTltIIfjGuA58+fN2zQT+puoGI
wzafjk9R73Foa67YKUwClaBGZNZbYOkB2iOk9a+/sku6k3jO14moybpMuL32dCVe
lutKd9D4n8/J5UHX3SHKHAZ9r2vp28rlaZa4wd79Ww5r+BLajUcrkjtr4GVT5k1k
WzzC0nUjE/zg1oV+PlakMolwK+iBCQYTT7S4r/OQAABQIkXXdtwmGvFUUXpGVF19
GUs52XI8QzK5504Xl+F7NF1+2zHovO11PTHnd+rAe6AfA/NGggtk6O1Y9R4tQHF9
TN6PHukNxUdTFfe6RTbSzPagpFydvQ==
=/4Ve
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The main focus of this release from a framework point of view has been
spi-mem where we've acquired support for a few new hardware features
which enable better performance on suitable hardware.
Otherwise mostly thanks to Arnd's cleanup efforts on old platforms
we've removed several obsolete drivers which just about balance out
the newer drivers we've added this cycle.
Summary:
- Allow drivers to flag if they are unidirectional.
- Support for DTR mode and hardware acceleration of dummy cycles in
spi-mem.
- Support for Allwinder H616, Intel Lightning Mountain, nVidia Tegra
QuadSPI, Realtek RTL838x and RTL839x.
- Removal of obsolete EFM32, Txx9 and SIRF Prima and Atlas drivers"
* tag 'spi-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (76 commits)
spi: Skip zero-length transfers in spi_transfer_one_message()
spi: dw: Avoid stack content exposure
spi: cadence-quadspi: Use spi_mem_dtr_supports_op()
spi: spi-mem: add spi_mem_dtr_supports_op()
spi: atmel-quadspi: Disable the QSPI IP at suspend()
spi: pxa2xx: Add IDs for the controllers found on Intel Lynxpoint
spi: pxa2xx: Fix the controller numbering for Wildcat Point
spi: Change provied to provided in the file spi.h
spi: mediatek: add set_cs_timing support
spi: support CS timing for HW & SW mode
spi: add power control when set_cs_timing
spi: stm32: make spurious and overrun interrupts visible
spi: stm32h7: replace private SPI_1HZ_NS with NSEC_PER_SEC
spi: stm32: defer probe for reset
spi: stm32: driver uses reset controller only at init
spi: stm32h7: ensure message are smaller than max size
spi: stm32: use bitfield macros
spi: stm32: do not mandate cs_gpio
spi: stm32: properly handle 0 byte transfer
spi: clps711xx: remove redundant white-space
...
- Update ACPICA code in the kernel to upstream revision 20201113
with changes as follows:
* Remove the MTMR (Mid-Timer) table (Al Stone).
* Remove the VRTC table (Al Stone).
* Add type casts for string functions (Bob Moore).
* Update all copyrights to 2021 (Bob Moore).
* Fix exception code class checks (Maximilian Luz).
* Clean up exception code class checks (Maximilian Luz).
* Fix -Wfallthrough (Nick Desaulniers).
- Add support for setting and reading global profile of the platform
along with documentation (Mark Pearson, Hans de Goede, Jiaxun Yang).
- Fix fwnode properties matching and clean up the code handling
device properties and its documentation (Rafael Wysocki, Andy
Shevchenko).
- Clean up ACPI-based device enumeration code (Rafael Wysocki).
- Clean up the CPPC support library code (Ionela Voinescu).
- Clean up the APEI support code (Yang Li, Yazen Ghannam).
- Update GPIO-related properties documentation (Flavio Suligoi).
- Consolidate and clean up the printing of messages in several
places (Rafael Wysocki).
- Fix error code path in configfs handling code (Qinglang Miao).
- Use DEVICE_ATTR_<RW|RO|WO> macros where applicable (Dwaipayan Ray).
- Replace tests for !ACPI_FAILURE with tests for ACPI_SUCCESS in
multiple places (Bjorn Helgaas).
-----BEGIN PGP SIGNATURE-----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=WpL7
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to upstream revision
20210105, fix and clean up the handling of device properties, add
support for setting global profile of the platform, clean up device
enumeration, the CPPC library, the APEI support and more, update the
documentation, consolidate the printing of messages in several places
and make assorted janitorial changes.
Specifics:
- Update ACPICA code in the kernel to upstream revision 20201113 with
changes as follows:
* Remove the MTMR (Mid-Timer) table (Al Stone).
* Remove the VRTC table (Al Stone).
* Add type casts for string functions (Bob Moore).
* Update all copyrights to 2021 (Bob Moore).
* Fix exception code class checks (Maximilian Luz).
* Clean up exception code class checks (Maximilian Luz).
* Fix -Wfallthrough (Nick Desaulniers).
- Add support for setting and reading global profile of the platform
along with documentation (Mark Pearson, Hans de Goede, Jiaxun
Yang).
- Fix fwnode properties matching and clean up the code handling
device properties and its documentation (Rafael Wysocki, Andy
Shevchenko).
- Clean up ACPI-based device enumeration code (Rafael Wysocki).
- Clean up the CPPC support library code (Ionela Voinescu).
- Clean up the APEI support code (Yang Li, Yazen Ghannam).
- Update GPIO-related properties documentation (Flavio Suligoi).
- Consolidate and clean up the printing of messages in several places
(Rafael Wysocki).
- Fix error code path in configfs handling code (Qinglang Miao).
- Use DEVICE_ATTR_<RW|RO|WO> macros where applicable (Dwaipayan Ray).
- Replace tests for !ACPI_FAILURE with tests for ACPI_SUCCESS in
multiple places (Bjorn Helgaas)"
* tag 'acpi-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (44 commits)
ACPI: property: Satisfy kernel doc validator (part 2)
ACPI: property: Satisfy kernel doc validator (part 1)
ACPI: property: Make acpi_node_prop_read() static
ACPI: property: Remove dead code
ACPI: property: Fix fwnode string properties matching
ACPI: OSL: Clean up printing messages
ACPI: OSL: Rework acpi_check_resource_conflict()
ACPI: APEI: ERST: remove unneeded semicolon
ACPI: thermal: Clean up printing messages
ACPI: video: Clean up printing messages
ACPI: button: Clean up printing messages
ACPI: battery: Clean up printing messages
ACPI: AC: Clean up printing messages
ACPI: bus: Drop ACPI_BUS_COMPONENT which is not used any more
ACPI: utils: Clean up printing messages
ACPI: scan: Clean up printing messages
ACPI: bus: Clean up printing messages
ACPI: PM: Clean up printing messages
ACPI: power: Clean up printing messages
ACPI: APEI: Add is_generic_error() to identify GHES sources
...
There are a lot of platforms that have not seen any interesting code
changes in the past five years or more.
I made a list and asked around which ones are no longer in use [1], and
received confirmation about six ARM platforms and the TI C6x architecture
that have all reached the end of their life upstream, with no known
users remaining:
- efm32 -- added in 2011, first Cortex-M, no notable changes after 2013
- picoxcell -- added in 2011, abandoned after 2012 acquisition
- prima2 -- added in 20111, no notable changes since 2015
- tango -- added in 2015, sporadic changes until 2017, but abandoned
- u300 -- added in 2009, no notable changes since 2013
- zx --added in 2015 for both 32, 2017 for 64 bit, no notable changes
- arch/c6x -- added in 2011, but work stalled soon after that
A number of other platforms on the original list turned out to still
have users. In some cases there are out-of-tree patches and users
that plan to contribute them in the future, in other cases the code
is complete and works reliably.
[1] https://lore.kernel.org/lkml/CAK8P3a2DZ8xQp7R=H=wewHnT2=a_=M53QsZOueMVEf7tOZLKNg@mail.gmail.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=pf3b
-----END PGP SIGNATURE-----
Merge tag 'arm-platform-removal-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform removals from Arnd Bergmann:
"There are a lot of platforms that have not seen any interesting code
changes in the past five years or more.
I made a list and asked around which ones are no longer in use, and
received confirmation about six ARM platforms and the TI C6x
architecture that have all reached the end of their life upstream,
with no known users remaining:
- efm32 - added in 2011, first Cortex-M, no notable changes after 2013
- picoxcell - added in 2011, abandoned after 2012 acquisition
- prima2 - added in 20111, no notable changes since 2015
- tango - added in 2015, sporadic changes until 2017, but abandoned
- u300 - added in 2009, no notable changes since 2013
- zx - added in 2015 for both 32, 2017 for 64 bit, no notable changes
- arch/c6x - added in 2011, but work stalled soon after that
A number of other platforms on the original list turned out to still
have users. In some cases there are out-of-tree patches and users that
plan to contribute them in the future, in other cases the code is
complete and works reliably"
Link: https://lore.kernel.org/lkml/CAK8P3a2DZ8xQp7R=H=wewHnT2=a_=M53QsZOueMVEf7tOZLKNg@mail.gmail.com/
* tag 'arm-platform-removal-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: remove u300 platform
ARM: remove tango platform
ARM: remove zte zx platform
ARM: remove sirf prima2/atlas platforms
c6x: remove architecture
MAINTAINERS: Remove deleted platform efm32
ARM: drop efm32 platform
ARM: Remove PicoXcell platform support
ARM: dts: Remove PicoXcell platforms
With the introduction of 26751de25d ("spi: bcm2835: Micro-optimise
FIFO loops") it has become apparent that some users might initiate
zero-length SPI transfers. A fact the micro-optimization omitted, and
which turned out to cause crashes[1].
Instead of changing the micro-optimization itself, use a bigger hammer
and skip zero-length transfers altogether for drivers using the default
transfer_one_message() implementation.
Reported-by: Phil Elwell <phil@raspberrypi.com>
Fixes: 26751de25d ("spi: bcm2835: Micro-optimise FIFO loops")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
[1] https://github.com/raspberrypi/linux/issues/4100
Link: https://lore.kernel.org/r/20210211180820.25757-1-nsaenzjulienne@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Since "data" is u32, &data is a "u32 *" type, which means pointer math
will move in u32-sized steps. This was meant to be a byte offset, so
cast &data to "char *" to aim the copy into the correct location.
Seen with -Warray-bounds (and found by Coverity):
In file included from ./include/linux/string.h:269,
from ./arch/powerpc/include/asm/paca.h:15,
from ./arch/powerpc/include/asm/current.h:13,
from ./include/linux/mutex.h:14,
from ./include/linux/notifier.h:14,
from ./include/linux/clk.h:14,
from drivers/spi/spi-dw-bt1.c:12:
In function 'memcpy',
inlined from 'dw_spi_bt1_dirmap_copy_from_map' at drivers/spi/spi-dw-bt1.c:87:3:
./include/linux/fortify-string.h:20:29: warning: '__builtin_memcpy' offset 4 is out of the bounds [0, 4] of object 'data' with type 'u32' {aka 'unsigned int'} [-Warray-bounds]
20 | #define __underlying_memcpy __builtin_memcpy
| ^
./include/linux/fortify-string.h:191:9: note: in expansion of macro '__underlying_memcpy'
191 | return __underlying_memcpy(p, q, size);
| ^~~~~~~~~~~~~~~~~~~
drivers/spi/spi-dw-bt1.c: In function 'dw_spi_bt1_dirmap_copy_from_map':
drivers/spi/spi-dw-bt1.c:77:6: note: 'data' declared here
77 | u32 data;
| ^~~~
Addresses-Coverity: CID 1497771 Out-of-bounds access
Fixes: abf0090753 ("spi: dw: Add Baikal-T1 SPI Controller glue driver")
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20210211203714.1929862-1-keescook@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newly introduced spi_mem_dtr_supports_op() to check DTR op
support. This means the buswidth check does not need to be replicated.
It also happens to fix a bug where STR ops with a 2-byte opcode would be
reported as supported.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210204141218.32229-2-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_mem_default_supports_op() rejects DTR ops by default to ensure that
the controller drivers that haven't been updated with DTR support
continue to reject them. It also makes sure that controllers that don't
support DTR mode at all (which is most of them at the moment) also
reject them.
This means that controller drivers that want to support DTR mode can't
use spi_mem_default_supports_op(). Driver authors have to roll their own
supports_op() function and mimic the buswidth checks. See
spi-cadence-quadspi.c for example. Or even worse, driver authors might
skip it completely or get it wrong.
Add spi_mem_dtr_supports_op(). It provides a basic sanity check for DTR
ops and performs the buswidth requirement check. Move the logic for
checking buswidth in spi_mem_default_supports_op() to a separate
function so the logic is not repeated twice.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210204141218.32229-1-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It is safer to disable the QSPI IP at suspend, in order to avoid
possible impact of glitches on the internal FSMs. This is a theoretical
fix, there were no problems seen as of now. Tested on sama5d2 and
sam9x60 versions of the IP.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210210135428.204134-1-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
get_tbl() is confusing as it returns the content TBL register
on PPC32 but the concatenation of TBL and TBU on PPC64.
Use mftb() instead.
This will allow the removal of get_tbl() in a following patch.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/99bf008e2970de7f8ed3225cda69a6d06ae1a644.1612866360.git.christophe.leroy@csgroup.eu
Add IDs for the controllers found on Intel Lynxpoint.
In particular it's Macbook Air 6,2 devices.
Cc: Leif Liddy <leif.liddy@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210208163816.22147-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Wildcat Point has two SPI controllers and added one is actually second one.
Fix the numbering by adding the description of the first one.
Fixes: caba248db2 ("spi: spi-pxa2xx-pci: Add ID and driver type for WildcatPoint PCH")
Cc: Leif Liddy <leif.liddy@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210208163816.22147-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We do not expect to receive spurious interrupts so rise a warning
if it happens.
RX overrun is an error condition that signals a corrupted RX
stream both in dma and in irq modes. Report the error and
abort the transfer in either cases.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/1612551572-495-9-git-send-email-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace SPI_1HZ_NS private constant with NSEC_PER_SEC, which is easier
to read and understand.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/1612551572-495-8-git-send-email-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Defer the probe operation when a reset controller device is expected
but have not yet been probed.
This change replaces use of devm_reset_control_get_exclusive() with
devm_reset_control_get_optional_exclusive() as reset controller is
optional which is now explicitly stated.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/1612551572-495-7-git-send-email-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove reset controller device reference from the device private
structure since it is used only at probe time and can be discarded
once used to reset the SPI device.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/1612551572-495-6-git-send-email-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Ensure that messages given to transfer_one handler can actually be
handled by it. For that purpose rely on the SPI framework
spi_split_transfers_maxsize function to split messages whenever necessary.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/1612551572-495-5-git-send-email-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To avoid defining shift and mask separately and hand-coding the bit
manipulation, use the bitfield macros.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/1612551572-495-4-git-send-email-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver likely also supports earlier (RTL8196) and later (RTL93xx)
SoCs.
The SPI hardware in these SoCs is specifically intended for connecting NOR
bootflash chips, and only used for that in dozens of examined devices.
However boiled down to basics, it's really just a half-duplex SPI
controller.
The hardware appears to have a vestigial second chip-select control, but
it hasn't been seen in the wild and is thus not supported.
Signed-off-by: Bert Vermeulen <bert@biot.com>
Link: https://lore.kernel.org/r/20210120135928.246054-3-bert@biot.com
Signed-off-by: Mark Brown <broonie@kernel.org>
All amba drivers return 0 in their remove callback. Together with the
driver core ignoring the return value anyhow, it doesn't make sense to
return a value here.
Change the remove prototype to return void, which makes it explicit that
returning an error value doesn't work as expected. This simplifies changing
the core remove callback to return void, too.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org> # for drivers/memory
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com> # for hwtracing/coresight
Acked-By: Vinod Koul <vkoul@kernel.org> # for dmaengine
Acked-by: Guenter Roeck <linux@roeck-us.net> # for watchdog
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Takashi Iwai <tiwai@suse.de> # for sound
Acked-by: Vladimir Zapolskiy <vz@mleia.com> # for memory/pl172
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210126165835.687514-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Commit 7a2da5d796 ("spi: fsl: Fix driver breakage when SPI_CS_HIGH
is not set in spi->mode") broke our MPC8309 board by effectively
inverting the boolean value passed to fsl_spi_cs_control. The
SPISEL_BOOT signal is used as chipselect, but it's not a gpio, so
we cannot rely on gpiolib handling the polarity.
Adapt to the new world order by inverting the logic here. This does
assume that the slave sitting at the SPISEL_BOOT is active low, but
should that ever turn out not to be the case, one can create a stub
gpiochip driver controlling a single gpio (or rather, a single "spo",
special-purpose output).
Fixes: 7a2da5d796 ("spi: fsl: Fix driver breakage when SPI_CS_HIGH is not set in spi->mode")
Cc: stable@vger.kernel.org
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Link: https://lore.kernel.org/r/20210130143545.505613-1-rasmus.villemoes@prevas.dk
Signed-off-by: Mark Brown <broonie@kernel.org>
The double negative makes it hard to read "if (!ACPI_FAILURE(status))".
Replace it with "if (ACPI_SUCCESS(status))".
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The address mode is either 3 or 4 for the controller, which is configured
by the firmware and cannot be modified in the OS driver. Get the
firmware configuration and add address mode check in the .supports_op()
to block invalid operations.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Acked-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1611740450-47975-3-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The CSR SiRF prima2/atlas platforms are getting removed, so this driver
is no longer needed.
Cc: Barry Song <baohua@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Barry Song <baohua@kernel.org>
Link: https://lore.kernel.org/r/20210120161658.3820610-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
Link: https://lore.kernel.org/r/20200227143931.20688-1-sergiu.cuciurean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Release master that have been previously allocated if the number of
chipselect is invalid.
Fixes: 8e04187c1b ("spi: altera: add SPI core parameters support via platform data.")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20210120082635.49304-1-bianpan2016@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Ericsson U300 platform was one of two ARM929 based SoC platforms for
mobile phones in ST-Ericsson after the merger of Ericsson with ST-NXP
into ST-Ericsson, the other one being the ST Nomadik.
The platform was not widely adopted in Linux based systems and was
replaced with the far superior ST-Ericsson U8500 in 2011, but Linus
Walleij kept maintaining the code for the whole time.
Linus continues to use the Nomadik machine, but decided to drop
u300 from the kernel as part of this year's spring cleaning.
Thanks for having maintained it all these years.
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/lkml/CACRpkdbJkiHR9FSfJTH_5d_qRU1__dRXHM1TL40iqNRKbGQfrQ@mail.gmail.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The issue is that using SPI from a callback under the CCF lock will
deadlock, since this code uses clk_get_rate().
Fixes: c474b38665 ("spi: Add driver for Cadence SPI controller")
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210114154217.51996-1-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 766c6b63aa ("spi: fix client driver breakages when using GPIO
descriptors") broke fsl spi driver.
As now we fully rely on gpiolib for handling the polarity of
chip selects, the driver shall not alter the GPIO value anymore
when SPI_CS_HIGH is not set in spi->mode.
Fixes: 766c6b63aa ("spi: fix client driver breakages when using GPIO descriptors")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/6b51cc2bfbca70d3e9b9da7b7aa4c7a9d793ca0e.1610629002.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the struct spi_controller max_speed_hz. This is based on the
reported source clock frequency during probe. The maximum bus clock
is half the source clock (as per the code in bcm2835_spi_transfer_one).
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210107164825.21919-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi Mark,
This patch series makes the Renesas MSIOF SPI driver fill in actual
transfer speeds and controller limits, so the SPI core can take them
into account.
This has been tested on R-Car Gen2 and Gen3.
Thanks!
Geert Uytterhoeven (2):
spi: sh-msiof: Fill in spi_transfer.effective_speed_hz
spi: sh-msiof: Fill in controller speed limits
drivers/spi/spi-sh-msiof.c | 14 +++++++++++---
1 file changed, 11 insertions(+), 3 deletions(-)
--
2.25.1
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
Add QSPI controller support for Intel LGM SoC.
Patches to move move bindings over to
"Documentation/devicetree/bindings/spi/" directory and also added compatible
Support for Intel platform.
dt-bindings: spi: cadence-qspi: Add support for Intel lgm-qspi
(earlier patch mail thread and Ack-by)
link: "https://lore.kernel.org/lkml/5d6d1b85.1c69fb81.96938.0315@mx.google.com/"
Reference:
https://lkml.org/lkml/2020/6/1/50
---
v9:
- Vignesh review comments address and update
- Retain the patchv4 move the binding documentation from mtd to spi
directory.
- Add intel's compatible string over the legacy documentation
- Remove unused variable, CQSPI_SUPPORTS_MULTI_CHIPSELECT macro and check
- YAML convertion patch alone dropped
v8:
- As Mark suggested to add the dt-bindings documentation patches
end of the series , so dropped.
v7:
- Rob's review comments address and fixed dt-schema warning
- Pratyush review comments address and update
- DAC bit reset to 0 and 1 (enable/disable)
- tested QSI-NOR flash mx25l12805d on LGM soc, it's working after disable DAC
- Linus suggested to use 'num-cs' prperty instead of 'num-chipselect'
v6:
- Rob's review comments update
- add compatible string in properly aligned
- remove cadence-qspi extra comaptible string in example
v5:
- Rob's review comments update
- const with single compatible string kept
v4:
- Rob's review comments update
- remove '|' no formatting to preserve
- child node attributes follows under 'properties' under '@[0-9a-f]+$'.
v3:
- Pratyush review comments update
- CQSPI_SUPPORTS_MULTI_CHIPSELECT macro used instead of cqspi->use_direct_mode
- disable DAC support placed in end of controller_init
v2:
- Rob's review comments update for dt-bindings
- add 'oneOf' for compatible selection
- drop un-neccessary descriptions
- add the cdns,is-decoded-cs and cdns,rclk-en properties as schema
- remove 'allOf' in not required place
- add AdditionalProperties false
- add minItems/maxItems for qspi reset attributes
resend-v1:
- As per Mark's suggestion , reorder the patch series 1-3 driver
support patches, series 4-6 dt-bindings patches.
v1:
- initial version
Ramuthevar Vadivel Murugan (5):
spi: cadence-quadspi: Add QSPI support for Intel LGM SoC
spi: cadence-quadspi: Disable the DAC for Intel LGM SoC
spi: cadence-quadspi: Add multi-chipselect support for Intel LGM SoC
spi: Move cadence-quadspi.txt to Documentation/devicetree/bindings/spi
dt-bindings: spi: cadence-qspi: Add support for Intel lgm-qspi
.../bindings/{mtd => spi}/cadence-quadspi.txt | 1 +
drivers/spi/Kconfig | 2 +-
drivers/spi/spi-cadence-quadspi.c | 24 ++++++++++++++++++----
3 files changed, 22 insertions(+), 5 deletions(-)
rename Documentation/devicetree/bindings/{mtd => spi}/cadence-quadspi.txt (97%)
--
2.11.0
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Simplify stm32h7_spi_prepare_fthlv() function implementation,
no functional change intended.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alain Volmat <alain.volmat@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Cc: Antonio Borneo <antonio.borneo@st.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Roman Guskov <rguskov@dh-electronics.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-spi@vger.kernel.org
Link: https://lore.kernel.org/r/20210104123114.261596-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need to force this to be trigger high here, as the firmware
properly configures the irq flags already. Drop it to save a line.
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Mukesh Kumar Savaliya <msavaliy@codeaurora.org>
Cc: Akash Asthana <akashast@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210112001301.687628-1-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently we use concrete version to determine the max_cmd_dword.
New entries should be added for compatible hardwares of new version
or on new platform, otherwise the device will use 16 dwords instead
of 64 even if it supports, which will degrade the performance.
This will decrease the compatibility and the maintainability.
Drop the switch-case statement of the version checking. Only version
less than 0x351 supports maximum 16 command dwords.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Acked-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1610526716-14882-1-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fill in the controller speed limits, so the SPI core can use them for
validating SPI transfers, and adjust or reject transfers when needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210113101916.1147695-3-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Fill in the effective bit rate used for transfers, so the SPI core can
calculate instead of estimate delays.
Restore "reverse Christmas tree" order of local variables while adding
new variables.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210113101916.1147695-2-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
On Intel Lightning Mountain(LGM) SoCs QSPI controller do not use
Direct Access Controller(DAC).
This patch adds a quirk to disable the Direct Access Controller
for data transfer instead it uses indirect data transfe
DAC bit resets to 1 so there is no need to explicitly set it.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Link: https://lore.kernel.org/r/20201124041840.31066-3-vadivel.muruganx.ramuthevar@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With CONFIG_PM_SLEEP disabled the rpcif_spi_pm_ops variable is still
referenced and thus increasing the size of kernel.
Fix this issue by adding CONFIG_PM_SLEEP #ifdef check around the .pm
assignment (image size is critical on RZ/A SoC's where the SRAM sizes
range 4~5 MiB).
Fixes: 9584fc95ca ("spi: rpc-if: Remove CONFIG_PM_SLEEP ifdefery")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Suggested-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210107145329.27966-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The kernel test robot reports the following warning.
drivers/spi/spi-cadence-quadspi.c:966:24: warning: comparison of distinct pointer types ('typeof (len) *' (aka 'unsigned int *') and 'typeof (500UL) *' (aka 'unsigned long *')) [-Wcompare-distinct-pointer-types]
msecs_to_jiffies(max(len, 500UL)))) {
^~~~~~~~~~~~~~~
include/linux/minmax.h:58:19: note: expanded from macro 'max'
#define max(x, y) __careful_cmp(x, y, >)
^~~~~~~~~~~~~~~~~~~~~~
include/linux/minmax.h:42:24: note: expanded from macro '__careful_cmp'
__builtin_choose_expr(__safe_cmp(x, y), \
^~~~~~~~~~~~~~~~
include/linux/minmax.h:32:4: note: expanded from macro '__safe_cmp'
(__typecheck(x, y) && __no_side_effects(x, y))
^~~~~~~~~~~~~~~~~
include/linux/minmax.h:18:28: note: expanded from macro '__typecheck'
(!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
~~~~~~~~~~~~~~ ^ ~~~~~~~~~~~~~~
1 warning generated.
This happens because size_t is unsigned long on 64-bit platforms like
arm64 but it is unsigned int on 32-bit platforms like arm. Omitting the
"UL" would result in a warning on 64-bit platforms. Squash it by type
casting the arguments to size_t using max_t(). This way builds on both
type of platforms can be satisfied. There is no chance of any truncation
since 500 is small enough to fit into both int and long.
Fixes: f453f29397 ("spi: cadence-quadspi: Wait at least 500 ms for direct reads")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210108181457.30291-1-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix a new warning report by build for make ARCH=MIPS allmodconfig:
drivers/spi/spi-cadence-quadspi.c: In function 'cqspi_direct_read_execute':
./include/linux/minmax.h:18:28: warning: comparison of distinct pointer types lacks a cast
18 | (!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
| ^~
./include/linux/minmax.h:32:4: note: in expansion of macro '__typecheck'
32 | (__typecheck(x, y) && __no_side_effects(x, y))
| ^~~~~~~~~~~
./include/linux/minmax.h:42:24: note: in expansion of macro '__safe_cmp'
42 | __builtin_choose_expr(__safe_cmp(x, y), \
| ^~~~~~~~~~
./include/linux/minmax.h:58:19: note: in expansion of macro '__careful_cmp'
58 | #define max(x, y) __careful_cmp(x, y, >)
| ^~~~~~~~~~~~~
drivers/spi/spi-cadence-quadspi.c:1153:24: note: in expansion of macro 'max'
1153 | msecs_to_jiffies(max(len, 500UL)))) {
| ^~~
"len" is unsigned,however,"500" is unsigned long.
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Link: https://lore.kernel.org/r/20210107115704.3835282-1-siyanteng@loongson.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
This series adds Tegra210, Tegra186, and Tegra194 Quad SPI driver and
enables Quad SPI on Jetson Nano and Jetson Xavier NX.
QSPI controller is available on Tegra210, Tegra186 and Tegra194.
Tegra186 and Tegra194 has additional feature of combined sequence mode
where command, address and data can all be transferred in a single transfer.
Combined sequence mode is useful only when using DMA mode transfer.
This series does not have combined sequence mode feature as Tegra186/Tegra194
GPCDMA driver is not upstreamed yet.
This series includes
- dt-binding document
- QSPI driver for Tegra210/Tegra186/Tegra194
- Enables QSPI on Jetson Nano and Jetson Xavier NX.
Delta between patch versions:
[v5]: Simplified implementation in Patch-0006
[v4]: Updated dummy cycles implementation based on v3 feedback
- Added dummy_data bit field int spi_transfer to indicate corresponding
transfer is dummy bytes transfer.
- Updated Tegra QSPI transfer_one_message to identify dummy transfer and
to use HW supported dummy bytes transfer when dummy cycles are with in
Tegra QSPI supported max HW dummy cycles otherwise fallsback to transfer
dummy bytes from software.
- Updated dt-bindings based on v3 feedback.
[v3]: v2 has some mixed patches sent out accidentally.
v3 sends proper patches with fixes mentioned in v2.
[v2]: below v1 feedback
- Added SPI_MASTER_USES_HW_DUMMY_CYCLES flag for controllers supporting
hardware dummy cycles and skips dummy bytes transfer from software for
these controllers.
- Updated dt-binding doc with tx/rx tap delay properties.
- Added qspi_out clock to dt-binding doc which will be used later with
ddr mode support.
- All other v1 feedback on some cleanup.
Sowjanya Komatineni (9):
dt-bindings: clock: tegra: Add clock ID TEGRA210_CLK_QSPI_PM
dt-bindings: spi: Add Tegra Quad SPI device tree binding
MAINTAINERS: Add Tegra Quad SPI driver section
spi: tegra210-quad: Add support for Tegra210 QSPI controller
spi: spi-mem: Mark dummy transfers by setting dummy_data bit
spi: tegra210-quad: Add support for hardware dummy cycles transfer
arm64: tegra: Enable QSPI on Jetson Nano
arm64: tegra: Add QSPI nodes on Tegra194
arm64: tegra: Enable QSPI on Jetson Xavier NX
.../bindings/spi/nvidia,tegra210-quad.yaml | 117 ++
MAINTAINERS | 8 +
.../dts/nvidia/tegra194-p3509-0000+p3668-0000.dts | 12 +
arch/arm64/boot/dts/nvidia/tegra194.dtsi | 28 +
arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts | 12 +
arch/arm64/boot/dts/nvidia/tegra210.dtsi | 5 +-
drivers/spi/Kconfig | 9 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-mem.c | 1 +
drivers/spi/spi-tegra210-quad.c | 1410 ++++++++++++++++++++
include/dt-bindings/clock/tegra210-car.h | 2 +-
include/linux/spi/spi.h | 2 +
12 files changed, 1604 insertions(+), 3 deletions(-)
create mode 100644 Documentation/devicetree/bindings/spi/nvidia,tegra210-quad.yaml
create mode 100644 drivers/spi/spi-tegra210-quad.c
--
2.7.4
Tegra Quad SPI controller hardware supports sending dummy bytes based
on programmed dummy clock cycles after the actual transfer bytes.
This patch adds this support of hardware dummy bytes transfer and
skips transfer of dummy bytes from the software.
For dummy cycles more than Tegra Quad SPI hardware maximum dummy
cycles limit, driver transfers dummy bytes from the software.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1608585459-17250-7-git-send-email-skomatineni@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch marks dummy transfer by setting dummy_data bit to 1.
Controllers supporting dummy transfer by hardware use this bit field
to skip software transfer of dummy bytes and use hardware dummy bytes
transfer.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1608585459-17250-6-git-send-email-skomatineni@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Double Transfer Rate (DTR) mode transfers data twice per clock cycle.
Add support for parsing DTR ops and set up the registers to allow it.
Most SPI NOR flashes expect 2 byte commands. Parse the 2-byte opcode
from SPI MEM and set it up in the CQSPI_REG_OP_EXT_LOWER register.
Increment the delay needed before issuing indirect writes because larger
delay is needed for DTR mode. With the current delay some writes end up
missing.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-8-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When performing a direct read via DMA the timeout for completion is set
equal to the read length. This is fine for larger reads. For a small
read like the Read Status Register command, the timeout would be 1 or 2
milliseconds. This is not enough to cover the overhead needed in setting
up DMA.
Make sure the timeout is at least 500 ms to allow DMA ample time to
finish. For reads larger than 500 bytes, the timeout will continue to be
equal to the read length.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20201222184425.7028-7-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The default SPI MEM supports_op hook rejects DTR ops by default. Add a
simple supports_op hook that very closely imitates the SPI MEM one. It
will be extended in later commits to allow DTR ops.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-6-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI MEM deals with dummy bytes but the controller deals with dummy
cycles. Multiplying bytes by 8 is correct if the dummy phase uses 1S
mode since 1 byte will be sent in 8 cycles. But if the dummy phase uses
4S mode then 1 byte will be sent in 2 cycles.
To correctly translate dummy bytes to dummy cycles, the dummy buswidth
also needs to be taken into account. Divide 8 by the buswidth to get the
correct multiplier for getting the number of cycles.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-5-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If a command does not have an address phase it goes via the STIG path.
The dummy cycles are not initialized for the STIG commands. As a result,
STIG commands with dummy cycles will not work.
Initialize the dummy cycle field before issuing the STIG command to make
sure it is sent correctly. Move the code to calculate dummy cycle value
to a separate function so it is not repeated twice. DTR support will add
some more logic here to it is worth it to extract it out in a function.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-4-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The controller can only support up to 31 dummy cycles. If the command
requires more it falls back to using 31. This command is likely to fail
because the correct number of cycles are not waited upon. Rather than
silently issuing an incorrect command, fail loudly so the caller can get
a chance to find out the command can't be supported by the controller.
Fixes: 1406234105 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller")
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-3-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As of commit 9326e4f1e5 ("spi: Limit the spi device max speed to
controller's max speed"), the SPI device max speed is set to the
controller's max speed if it is larger. The Cadence QSPI controller does
not set the controller's max speed so it is left at its initial value of
0. This means the SPI device max speed is always set to 0.
The SPI device max speed is used to calculate the baud rate divider when
performing an operation. If this speed is 0, the default divider of 32
is used. No matter what speed is specified by the device tree property
'spi-max-frequency', the device will always operate at ref_clk / 32.
Fix this by setting master->max_speed_hz to the ref clock speed so the
correct divider can be calculated.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-2-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With the introduction of the 'include/uapi/linux/spi/spi.h' header, the
type of the macros are enforced to 'unsigned long int' via the _BITUL()
macro.
This causes some -Wformat warnings in the spi-stm32 driver.
This patch adds a double-negation operator to the bit-masks. Essentially,
the important values for debugging are 0 or 1, while masking them directly
would show 0 or BIT(x) values.
This way, the type of the arguments are automatically re-cast.
Fixes: f7005142da ("spi: uapi: unify SPI modes into a single spi.h header")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210104143103.56510-1-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI driver for the Renesas RPC-IF is present on the RZ/G2
Series. Add that to the description.
Suggested-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210102115412.3402059-3-aford173@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The xfer waiting time is the result of xfer->len / xfer->speed_hz. This
patch makes the assumption of 100khz xfer speed if the xfer->speed_hz is
not assigned and stays 0. This avoids the divide by 0 issue and ensures
a reasonable tolerant waiting time.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/1609723749-3557-1-git-send-email-yilun.xu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use __maybe_unused for the suspend()/resume() hooks and get rid of
the CONFIG_PM_SLEEP ifdefery to improve the code.
Suggested-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Pavel Machek <pavel@denx.de>
Link: https://lore.kernel.org/r/20201230145708.28544-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If spi->controller->max_speed_hz is zero, a non-zero spi->max_speed_hz
will be overwritten by zero. Make sure spi->controller->max_speed_hz
is not zero when clamping spi->max_speed_hz.
Put the spi->controller->max_speed_hz non-zero check higher in the if,
so that we avoid a superfluous init to zero when both spi->max_speed_hz
and spi->controller->max_speed_hz are zero.
Fixes: 9326e4f1e5 ("spi: Limit the spi device max speed to controller's max speed")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201216092321.413262-1-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the return value for altera_spi_txrx. It should return
1 for interrupt transfer mode, and return 0 for polling transfer mode.
The altera_spi_txrx() implements the spi_controller.transfer_one
callback. According to the spi-summary.rst, the transfer_one should
return 0 when transfer is finished, return 1 when transfer is still in
progress.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/1609219662-27057-2-git-send-email-yilun.xu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Transmit/receive only is a valid SPI mode. For example, the MOSI/TX line
might be missing from an ADC while for a DAC the MISO/RX line may be
optional. This patch adds these two new modes: SPI_NO_TX and
SPI_NO_RX. This way, the drivers will be able to identify if any of
these two lines is missing and to adjust the transfers accordingly.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201221152936.53873-2-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some SPI devices, require toggling the CS every transferred byte.
Enable such possibility in the spi-orion driver.
Note that in order to use it, in the driver of a secondary device
attached to this controller, the SPI bus 'mode' field must be
updated with SPI_CS_WORD flag before calling spi_setup() routine.
In addition to that include a work-around - some devices, such as
certain models of SLIC (Subscriber Line Interface Card),
may require extra delay after CS toggling, so add a minimal
timing relaxation in relevant places.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Link: https://lore.kernel.org/r/20201223103827.29721-3-kostap@marvell.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-orion driver disables its clocks whenever it is not used.
In usual case during boot (i.e. using SPI flash) it is not a problem,
as the child device driver is present and probed along with
spi_register_master() execution.
However in case the child device driver is not ready
(e.g. when its type is module_spi_driver) the spi_setup() callback
can be called after the spi-orion probe. It may happen,
that as a result there will be an attempt to access controller's
registers with the clocks disabled.
Prevent such situations and make sure the clocks are on,
each time the spi_setup() is called.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Link: https://lore.kernel.org/r/20201223103827.29721-2-kostap@marvell.com
Signed-off-by: Mark Brown <broonie@kernel.org>
if cur_bpw <= 8 and xfer_len < 4 then the value of fthlv will be 1 and
SPI registers content may have been lost.
* If SPI data register is accessed as a 16-bit register and DSIZE <= 8bit,
better to select FTHLV = 2, 4, 6 etc
* If SPI data register is accessed as a 32-bit register and DSIZE > 8bit,
better to select FTHLV = 2, 4, 6 etc, while if DSIZE <= 8bit,
better to select FTHLV = 4, 8, 12 etc
Signed-off-by: Roman Guskov <rguskov@dh-electronics.com>
Fixes: dcbe0d84df ("spi: add driver for STM32 SPI controller")
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20201221123532.27272-1-rguskov@dh-electronics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If we're using geni to manage the chip select line (don't do it--use a
GPIO!) and we happen to get a timeout waiting for the chip select
command to be completed, no errors are printed even though things
might not be in the best shape. Let's add a print.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20201217142842.v3.4.I666b37646de9652cef438ac7c2c6c2053367fc6b@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
If we get a timeout sending then this happens:
spi_transfer_one_message()
->transfer_one() AKA spi_geni_transfer_one()
setup_fifo_xfer()
mas->cur_xfer = non-NULL
spi_transfer_wait() => TIMES OUT
if (msg->status != -EINPROGRESS)
goto out
if (ret != 0 ...)
spi_set_cs()
->set_cs AKA spi_geni_set_cs()
# mas->cur_xfer is non-NULL
The above happens _before_ the SPI core calls ->handle_err() AKA
handle_fifo_timeout().
Unfortunately that won't work so well on geni. If we got a timeout
transferring then it's likely that our interrupt handler is blocked,
but we need that same interrupt handler to run and the command channel
to be unblocked in order to adjust the chip select. Trying to set the
chip select doesn't crash us but ends up confusing our state machine
and leads to messages like: Premature done. rx_rem = 32 bpw8
Let's just drop the chip select request in this case. We can detect
the case because cur_xfer is non-NULL--it would have been set to NULL
in the interrupt handler if the previous transfer had finished. Sure,
we might leave the chip select in the wrong state but it's likely it
was going to fail anyway and this avoids getting the driver even more
confused about what it's doing.
The SPI core in general assumes that setting chip select is a simple
operation that doesn't fail. Yet another reason to just reconfigure
the chip select line as GPIOs.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20201217142842.v3.3.I07afdedcc49655c5d26880f8df9170aac5792378@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
If we got a timeout when trying to send an abort command then it means
that we just got 3 timeouts in a row:
1. The original timeout that caused handle_fifo_timeout() to be
called.
2. A one second timeout waiting for the cancel command to finish.
3. A one second timeout waiting for the abort command to finish.
SPI is clocked by the controller, so nothing (aside from a hardware
fault or a totally broken sequencer) should be causing the actual
commands to fail in hardware. However, even though the hardware
itself is not expected to fail (and it'd be hard to predict how we
should handle things if it did), it's easy to hit the timeout case by
simply blocking our interrupt handler from running for a long period
of time. Obviously the system is in pretty bad shape if a interrupt
handler is blocked for > 2 seconds, but there are certainly bugs (even
bugs in other unrelated drivers) that can make this happen.
Let's make things a bit more robust against this case. If we fail to
abort we'll set a flag and then we'll block all future transfers until
we have no more interrupts pending.
Fixes: 561de45f72 ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20201217142842.v3.2.Ibade998ed587e070388b4bf58801f1107a40eb53@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit 7ba9bdcb91 ("spi: spi-geni-qcom: Don't keep a local state
variable") we changed handle_fifo_timeout() so that we set
"mas->cur_xfer" to NULL to make absolutely sure that we don't mess
with the buffers from the previous transfer in the timeout case.
Unfortunately, this caused the IRQ handler to dereference NULL in some
cases. One case:
CPU0 CPU1
---- ----
setup_fifo_xfer()
geni_se_setup_m_cmd()
<hardware starts transfer>
<transfer completes in hardware>
<hardware sets M_RX_FIFO_WATERMARK_EN in m_irq>
...
handle_fifo_timeout()
spin_lock_irq(mas->lock)
mas->cur_xfer = NULL
geni_se_cancel_m_cmd()
spin_unlock_irq(mas->lock)
geni_spi_isr()
spin_lock(mas->lock)
if (m_irq & M_RX_FIFO_WATERMARK_EN)
geni_spi_handle_rx()
mas->cur_xfer NULL dereference!
tl;dr: Seriously delayed interrupts for RX/TX can lead to timeout
handling setting mas->cur_xfer to NULL.
Let's check for the NULL transfer in the TX and RX cases and reset the
watermark or clear out the fifo respectively to put the hardware back
into a sane state.
NOTE: things still could get confused if we get timeouts all the way
through handle_fifo_timeout() and then start a new transfer because
interrupts from the old transfer / cancel / abort could still be
pending. A future patch will help this corner case.
Fixes: 561de45f72 ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20201217142842.v3.1.I99ee04f0cb823415df59bd4f550d6ff5756e43d6@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Collected patches from the two series below and associated tags so they
can be merged in one pile through the spi tree. Merry December!
SPI: https://lore.kernel.org/r/20201202214935.1114381-1-swboyd@chromium.org
cros-ec: https://lore.kernel.org/r/20201203011649.1405292-1-swboyd@chromium.org
Cc: Akash Asthana <akashast@codeaurora.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Gwendal Grignou <gwendal@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Alexandru M Stan <amstan@chromium.org>
Stephen Boyd (3):
platform/chrome: cros_ec_spi: Don't overwrite spi::mode
platform/chrome: cros_ec_spi: Drop bits_per_word assignment
spi: spi-geni-qcom: Use the new method of gpio CS control
drivers/platform/chrome/cros_ec_spi.c | 2 --
drivers/spi/spi-geni-qcom.c | 1 +
2 files changed, 1 insertion(+), 2 deletions(-)
base-commit: b650545978
--
https://chromeos.dev
Let's set the 'use_gpio_descriptors' field so that we use the new way of
requesting the CS GPIOs in the core. This allows us to avoid having to
configure the CS pins in "output" mode with an 'output-enable' pinctrl
setting.
Cc: Akash Asthana <akashast@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20201204193540.3047030-4-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The Canaan Kendryte K210 RISC-V SoC includes a DW apb_ssi v4 controller
which is documented to have a 32 words deep TX and RX FIFO. The FIFO
length detection in spi_hw_init() correctly detects this value.
However, when the controller RX FIFO is filled up to 32 entries
(RXFLR = 32), an RX FIFO overrun error occurs. This likely due to a
hardware bug which can be avoided by force setting the fifo_len field of
struct dw_spi to 31.
Define the dw_spi_canaan_k210_init() function to force set fifo_len to
31 when the device node compatible string is "canaan,k210-spi".
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20201206011817.11700-4-damien.lemoal@wdc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Synopsis DesignWare DW_apb_ssi specifications version 3.23 onward
define a 32-bits maximum transfer size synthesis parameter
(SSI_MAX_XFER_SIZE=32) in addition to the legacy 16-bits configuration
(SSI_MAX_XFER_SIZE=16) for SPI controllers. When SSI_MAX_XFER_SIZE=32,
the layout of the ctrlr0 register changes, moving the data frame format
field from bits [3..0] to bits [16..20], and the RX/TX FIFO word size
can be up to 32-bits.
To support this new format, introduce the DW SPI capability flag
DW_SPI_CAP_DFS32 to indicate that a controller is configured with
SSI_MAX_XFER_SIZE=32. Since SSI_MAX_XFER_SIZE is a controller synthesis
parameter not accessible through a register, the detection of this
parameter value is done in spi_hw_init() by writing and reading the
ctrlr0 register and testing the value of bits [3..0]. These bits are
ignored (unchanged) for SSI_MAX_XFER_SIZE=16, allowing the detection.
If a DFS32 capable SPI controller is detected, the new field dfs_offset
in struct dw_spi is set to SPI_DFS32_OFFSET (16).
dw_spi_update_config() is modified to set the data frame size field at
the correct position is the CTRLR0 register, as indicated by the
dfs_offset field of the dw_spi structure.
The DW_SPI_CAP_DFS32 flag is also unconditionally set for SPI slave
controllers, e.g. controllers that have the DW_SPI_CAP_DWC_SSI
capability flag set. However, for these ssi controllers, the dfs_offset
field is set to 0 as before (as per specifications).
Finally, for any controller with the DW_SPI_CAP_DFS32 capability flag
set, dw_spi_add_host() extends the value of bits_per_word_mask from
16-bits to 32-bits. dw_reader() and dw_writer() are also modified to
handle 32-bits iTX/RX FIFO words.
Suggested-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20201206011817.11700-3-damien.lemoal@wdc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Starting with the move of the atmel-quadspi driver under SPI,
the following error could be seen when mounting a 16MByte ubifs:
UBIFS error (ubi0:0 pid 1893): check_lpt_type.constprop.6: invalid type (15) in LPT node type
1/4 fixes AHB accesses. The rest of the patches are small optimizations.
Tested on both sama5d2 and sam9x60.
Tudor Ambarus (4):
spi: atmel-quadspi: Fix AHB memory accesses
spi: atmel-quadspi: Drop superfluous set of QSPI_IFR_APBTFRTYP_READ
spi: atmel-quadspi: Write QSPI_IAR only when needed
spi: atmel-quadspi: Move common code outside of if else
drivers/spi/atmel-quadspi.c | 25 +++++++++++++------------
1 file changed, 13 insertions(+), 12 deletions(-)
--
2.25.1
base-commit: 3650b228f8
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
atmel_qspi_remove() accesses the driver's private data after calling
spi_unregister_controller() even though that function releases the last
reference on the spi_controller and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
Fixes: 2d30ac5ed6 ("mtd: spi-nor: atmel-quadspi: Use spi-mem interface for atmel-quadspi driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.0+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.0+
Cc: Piotr Bugalski <bugalski.piotr@gmail.com>
Link: https://lore.kernel.org/r/4b05c65cf6f1ea3251484fe9a00b4c65478a1ae3.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the call to devm_spi_register_master() fails on probe of the NPCM FIU
SPI driver, the clock "fiu->clk" is erroneously not unprepared and
disabled. Fix it.
Fixes: ace55c411b ("spi: npcm-fiu: add NPCM FIU controller driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.4+
Cc: Tomer Maimon <tmaimon77@gmail.com>
Link: https://lore.kernel.org/r/9ae62f4e1cfe542bec57ac2743e6fca9f9548f55.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the call to devm_spi_register_controller() fails on probe of the
Qualcomm Atheros AR934x/QCA95xx SPI driver, the spi_controller struct is
erroneously not freed. Fix by switching over to the new
devm_spi_alloc_master() helper.
Moreover, the controller's clock is enabled on probe but not disabled if
any of the subsequent probe steps fail.
Finally, there's an ordering issue in ar934x_spi_remove() wherein the
clock is disabled even though the controller is not yet unregistered.
It is unregistered after ar934x_spi_remove() by the devres framework.
As long as it is not unregistered, SPI transfers may still be ongoing
and disabling the clock may break them. It is not possible to use
devm_spi_register_controller() in this case, so move to the non-devm
variant.
All of these bugs have existed since the driver was first introduced,
so it seems fair to fix them together in a single commit.
Fixes: 047980c582 ("spi: add driver for ar934x spi controller")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.7+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.7+
Cc: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/1d58367d74d55741e0c2730a51a2b65012c8ab33.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the calls to device_reset() or devm_spi_register_controller() fail on
probe of the MediaTek MT7621 SPI driver, the spi_controller struct is
erroneously not freed. Fix by switching over to the new
devm_spi_alloc_master() helper.
Additionally, there's an ordering issue in mt7621_spi_remove() wherein
the spi_controller is unregistered after disabling the SYS clock.
The correct order is to call spi_unregister_controller() *before* this
teardown step because bus accesses may still be ongoing until that
function returns.
All of these bugs have existed since the driver was first introduced,
so it seems fair to fix them together in a single commit.
Fixes: 1ab7f2a435 ("staging: mt7621-spi: add mt7621 support")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: <stable@vger.kernel.org> # v4.17+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.17+
Link: https://lore.kernel.org/r/72b680796149f5fcda0b3f530ffb7ee73b04f224.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 702b15cb97 ("spi: mt7621: fix missing clk_disable_unprepare()
on error in mt7621_spi_probe") sought to disable the SYS clock on probe
errors, but only did so for 2 of 3 potentially failing calls: The clock
needs to be disabled on failure of devm_spi_register_controller() as
well.
Moreover, the commit purports to fix a bug in commit cbd66c626e ("spi:
mt7621: Move SPI driver out of staging") but in reality the bug has
existed since the driver was first introduced.
Fixes: 1ab7f2a435 ("staging: mt7621-spi: add mt7621 support")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.17+: 702b15cb9712: spi: mt7621: fix missing clk_disable_unprepare() on error in mt7621_spi_probe
Cc: <stable@vger.kernel.org> # v4.17+
Cc: Qinglang Miao <miaoqinglang@huawei.com>
Link: https://lore.kernel.org/r/36ad42760087952fb7c10aae7d2628547c26a7ec.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the call to devm_gpiod_get_optional() fails on probe of the NXP
SC18IS602/603 SPI driver, the spi_master struct is erroneously not freed.
Fix by switching over to the new devm_spi_alloc_master() helper.
Fixes: f99008013e ("spi: sc18is602: Add reset control via gpio pin.")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.9+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.9+
Cc: Phil Reid <preid@electromag.com.au>
Link: https://lore.kernel.org/r/d5f715527b894b91d530fe11a86f51b3184a4e1a.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the calls to devm_clk_get(), devm_spi_register_master() or
clk_prepare_enable() fail on probe of the Mikrotik RB4xx SPI driver,
the spi_master struct is erroneously not freed.
Fix by switching over to the new devm_spi_alloc_master() helper.
Fixes: 05aec35787 ("spi: Add SPI driver for Mikrotik RB4xx series boards")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.2+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.2+
Cc: Bert Vermeulen <bert@biot.com>
Link: https://lore.kernel.org/r/369bf26d71927f60943b1d9d8f51810f00b0237d.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the call to devm_spi_register_master() fails on probe of the GPIO SPI
driver, the spi_master struct is erroneously not freed:
After allocating the spi_master, its reference count is 1. The driver
unconditionally decrements the reference count on unbind using a devm
action. Before calling devm_spi_register_master(), the driver
unconditionally increments the reference count because on success,
that function will decrement the reference count on unbind. However on
failure, devm_spi_register_master() does *not* decrement the reference
count, so the spi_master is leaked.
The issue was introduced by commits 8b797490b4 ("spi: gpio: Make sure
spi_master_put() is called in every error path") and 79567c1a32 ("spi:
gpio: Use devm_spi_register_master()"), which sought to plug leaks
introduced by 9b00bc7b90 ("spi: spi-gpio: Rewrite to use GPIO
descriptors") but missed this remaining leak.
The situation was later aggravated by commit d3b0ffa1d7 ("spi: gpio:
prevent memory leak in spi_gpio_probe"), which introduced a
use-after-free because it releases a reference on the spi_master if
devm_add_action_or_reset() fails even though the function already
does that.
Fix by switching over to the new devm_spi_alloc_master() helper.
Fixes: 9b00bc7b90 ("spi: spi-gpio: Rewrite to use GPIO descriptors")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org> # v4.17+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.1-: 8b797490b4db: spi: gpio: Make sure spi_master_put() is called in every error path
Cc: <stable@vger.kernel.org> # v5.1-: 45beec351998: spi: bitbang: Introduce spi_bitbang_init()
Cc: <stable@vger.kernel.org> # v5.1-: 79567c1a321e: spi: gpio: Use devm_spi_register_master()
Cc: <stable@vger.kernel.org> # v5.4-: d3b0ffa1d75d: spi: gpio: prevent memory leak in spi_gpio_probe
Cc: <stable@vger.kernel.org> # v4.17+
Cc: Navid Emamdoost <navid.emamdoost@gmail.com>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Link: https://lore.kernel.org/r/86eaed27431c3d709e3748eb76ceecbfc790dd37.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the call to devm_spi_register_controller() fails on probe of the
MediaTek SPI NOR driver, the spi_controller struct is erroneously not
freed.
Since commit a1daaa991e ("spi: spi-mtk-nor: use dma_alloc_coherent()
for bounce buffer"), the same happens if the call to
dmam_alloc_coherent() fails.
Since commit 3bfd9103c7 ("spi: spi-mtk-nor: Add power management
support"), the same happens if the call to mtk_nor_enable_clk() fails.
Fix by switching over to the new devm_spi_alloc_master() helper.
Fixes: 881d1ee9fe ("spi: add support for mediatek spi-nor controller")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Ikjoon Jang <ikjn@chromium.org>
Cc: <stable@vger.kernel.org> # v5.7+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.7+
Cc: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/d5b9f0289465394e73dedb8ec51e180a8f1dffc9.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the calls to devm_clk_get() or devm_ioremap_resource() fail on probe
of the Macronix SPI driver, the spi_master struct is erroneously not freed.
Fix by switching over to the new devm_spi_alloc_master() helper.
Fixes: b942d80b0a ("spi: Add MXIC controller driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.0+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.0+
Cc: Mason Yang <masonccyang@mxic.com.tw>
Link: https://lore.kernel.org/r/4fa6857806e7e75741c05d057ac9df3564460114.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
rpcif_spi_remove() accesses the driver's private data after calling
spi_unregister_controller() even though that function releases the last
reference on the spi_controller and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
Fixes: eb8d6d464a ("spi: add Renesas RPC-IF driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.9+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.9+
Cc: Sergei Shtylyov <s.shtylyov@omprussia.ru>
Link: https://lore.kernel.org/r/c5da472c28021da2f6517441685cef033d40b140.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
pxa2xx_spi_remove() accesses the driver's private data after calling
spi_unregister_controller() even though that function releases the last
reference on the spi_controller and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master/slave() helper
which keeps the private data accessible until the driver has unbound.
Fixes: 32e5b57232 ("spi: pxa2xx: Fix controller unregister order")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v2.6.17+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v2.6.17+: 32e5b57232c0: spi: pxa2xx: Fix controller unregister order
Cc: <stable@vger.kernel.org> # v2.6.17+
Link: https://lore.kernel.org/r/5764b04d4a6e43069ebb7808f64c2f774ac6f193.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_sh_remove() accesses the driver's private data after calling
spi_unregister_master() even though that function releases the last
reference on the spi_master and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
Fixes: 680c1305e2 ("spi/spi_sh: use spi_unregister_master instead of spi_master_put in remove path")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v3.0+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v3.0+
Cc: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/6d97628b536baf01d5e3e39db61108f84d44c8b2.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
qcom_qspi_remove() accesses the driver's private data after calling
spi_unregister_master() even though that function releases the last
reference on the spi_master and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
Fixes: f79a158d37 ("spi: spi-qcom-qspi: Use OPP API to set clk/perf state")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.9+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.9+
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/b6d3c4dce571d78a532fd74f27def0d5dc8d8a24.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_geni_remove() accesses the driver's private data after calling
spi_unregister_master() even though that function releases the last
reference on the spi_master and thereby frees the private data.
Moreover, since commit 1a9e489e61 ("spi: spi-geni-qcom: Use OPP API to
set clk/perf state"), spi_geni_probe() leaks the spi_master allocation
if the calls to dev_pm_opp_set_clkname() or dev_pm_opp_of_add_table()
fail.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound and also
avoids the spi_master leak on probe.
Fixes: 561de45f72 ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.20+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.20+
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Girish Mahadevan <girishm@codeaurora.org>
Link: https://lore.kernel.org/r/dfa1d8c41b8acdfad87ec8654cd124e6e3cb3f31.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
davinci_spi_remove() accesses the driver's private data after it's been
freed with spi_master_put().
Fix by moving the spi_master_put() to the end of the function.
Fixes: fe5fd25409 ("spi: davinci: Use dma_request_chan() for requesting DMA channel")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: <stable@vger.kernel.org> # v4.7+
Link: https://lore.kernel.org/r/412f7eb1cf8990e0a3a2153f4c577298deab623e.1607286887.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
QSPI_IFR is set as the last QSPI Instruction Frame register
regardless of the sama5d2 or sam9x60 version of the IP. Move
the writing of QSPI_IFR outside of the IP specific code.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201207135959.154124-5-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
That bit describes the APB transfer type. We are writing
serial memory registers via AHB acesses, that bit does not
make sense in the current context.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201207135959.154124-3-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Following error was seen when mounting a 16MByte ubifs:
UBIFS error (ubi0:0 pid 1893): check_lpt_type.constprop.6: invalid type (15) in LPT node type
QSPI_IFR.TFRTYP was not set correctly. When data transfer is enabled
and one wants to access the serial memory through AHB in order to:
- read in the serial memory, but not a memory data, for example
a JEDEC-ID, QSPI_IFR.TFRTYP must be written to '0' (both sama5d2
and sam9x60).
- read in the serial memory, and particularly a memory data,
TFRTYP must be written to '1' (both sama5d2 and sam9x60).
- write in the serial memory, but not a memory data, for example
writing the configuration or the QSPI_SR, TFRTYP must be written
to '2' for sama5d2 and to '0' for sam9x60.
- write in the serial memory in particular to program a memory data,
TFRTYP must be written to '3' for sama5d2 and to '1' for sam9x60.
Fix the setting of the QSPI_IFR.TFRTYP field.
Fixes: 2d30ac5ed6 ("mtd: spi-nor: atmel-quadspi: Use spi-mem interface for atmel-quadspi driver")
Cc: <stable@vger.kernel.org> # v5.0+
Reported-by: Tom Burkart <tom@aussec.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201207135959.154124-2-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: abf0090753 ("spi: dw: Add Baikal-T1 SPI Controller glue driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/1607071357-33378-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If cs-gpios property is used in devicetree then ctlr->num_chipselect value
may be changed by spi_get_gpio_descs().
So use ctlr->max_native_cs instead of ctlr->num_chipselect to set SPI_MCR
Fixes: 4fcc7c2292 (spi: spi-fsl-dspi: Don't access reserved fields in SPI_MCR)
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Link: https://lore.kernel.org/r/20201201085916.63543-1-fido_max@inbox.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 0f0581b24b ("spi: fsl: Convert to use CS GPIO descriptors")
broke the use of the SPISEL_BOOT signal as a chip select on the
MPC8309.
pdata->max_chipselect, which becomes master->num_chipselect, must be
initialized to take into account the possibility that there's one more
chip select in use than the number of GPIO chip selects.
Cc: stable@vger.kernel.org # v5.4+
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Fixes: 0f0581b24b ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Link: https://lore.kernel.org/r/20201127152947.376-1-rasmus.villemoes@prevas.dk
Signed-off-by: Mark Brown <broonie@kernel.org>
I mistakenly added the select attributes to the SPI_DW_BT1_DIRMAP config
instead of having them defined in SPI_DW_BT1. If the kernel doesn't have
the MULTIPLEXER and MUX_MMIO configs manually enabled and the
SPI_DW_BT1_DIRMAP config hasn't been selected, Baikal-T1 SPI device will
always fail to be probed by the driver. Fix that and the error reported by
the test robot:
>> ld.lld: error: undefined symbol: devm_mux_control_get
>>> referenced by spi-dw-bt1.c
>>> spi/spi-dw-bt1.o:(dw_spi_bt1_sys_init) in archive drivers/built-in.a
by moving the MULTIPLEXER/MUX_MMIO configs selection to the SPI_DW_BT1
config.
Link: https://lore.kernel.org/lkml/202011161745.uYRlekse-lkp@intel.com/
Link: https://lore.kernel.org/linux-spi/20201116040721.8001-1-rdunlap@infradead.org/
Fixes: abf0090753 ("spi: dw: Add Baikal-T1 SPI Controller glue driver")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201127144612.4204-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
fixed the coccicheck:
drivers/spi/spi-dw-bt1.c:220:27-30: ERROR: Missing
resource_size with mem.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/1606114975-31362-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When SPI DW memory ops support was introduced, there was a check for
excluding controllers which supplied their own CS function. Even so,
the mem_ops pointer is *always* presented to the SPI core.
This causes the SPI core sanity check in spi_controller_check_ops() to
refuse registration, since a mem_ops pointer is being supplied without
an exec_op member function.
The end result is failure of the SPI DW driver on sparx5 and similar
platforms.
The fix in the core SPI DW driver is to avoid presenting the mem_ops
pointer if the exec_op function is not set.
Fixes: 6423207e57 (spi: dw: Add memory operations support)
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20201120213414.339701-1-lars.povlsen@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Shutdown bus function might be called on the unbound device, so add a
check if there is a driver before calling its shutdown function.
This fixes following kernel panic obserbed during system reboot:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000018
...
Call trace:
spi_shutdown+0x10/0x38
kernel_restart_prepare+0x34/0x40
kernel_restart+0x14/0x88
__do_sys_reboot+0x148/0x248
__arm64_sys_reboot+0x1c/0x28
el0_svc_common.constprop.3+0x74/0x198
do_el0_svc+0x20/0x98
el0_sync_handler+0x140/0x1a8
el0_sync+0x140/0x180
Code: f9403402 d1008041 f100005f 9a9f1021 (f9400c21)
---[ end trace 266c07205a2d632e ]---
Fixes: 9db34ee64c (spi: Use bus_type functions for probe, remove and shutdown)
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201124131523.32287-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If set active without increase the usage count of pm, the dont use
autosuspend function will call the suspend callback to close the two
clocks of spi because the usage count is reduced to -1.
This will cause the warning dump below when the defer-probe occurs.
[ 129.379701] ecspi2_root_clk already disabled
[ 129.384005] WARNING: CPU: 1 PID: 33 at drivers/clk/clk.c:952 clk_core_disable+0xa4/0xb0
So add the get noresume function before set active.
Fixes: 43b6bf406c spi: imx: fix runtime pm support for !CONFIG_PM
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/r/20201124085247.18025-1-xiaoning.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Given the case that bootloader(such as UEFI)'s FSPI driver might not
handle all interrupts before loading kernel, those legacy interrupts
would assert immidiately once kernel's FSPI driver enable them. Further,
if it was FSPI_INTR_IPCMDDONE, the irq handler nxp_fspi_irq_handler()
would call complete(&f->c) to notify others. However, f->c might not be
initialized yet at that time, then cause kernel panic.
Of cause, we should fix this issue within bootloader. But it would be
better to have this pacth to make dirver more robust (by clearing all
interrupt status bits before enabling interrupts).
Suggested-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Link: https://lore.kernel.org/r/20201123025715.14635-1-ran.wang_1@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
I've discovered that due to the recent commit 49d7d695ca ("spi: dw:
Explicitly de-assert CS on SPI transfer completion") a concurrent usage of
the spidev devices with different chip-selects causes the "SPI transfer
timed out" error. The root cause of the problem has turned to be in a race
condition of the SPI-transfer execution procedure and the spi_setup()
method being called at the same time. In particular in calling the
spi_set_cs(false) while there is an SPI-transfer being executed. In my
case due to the commit cited above all CSs get to be switched off by
calling the spi_setup() for /dev/spidev0.1 while there is an concurrent
SPI-transfer execution performed on /dev/spidev0.0. Of course a situation
of the spi_setup() being called while there is an SPI-transfer being
executed for two different SPI peripheral devices of the same controller
may happen not only for the spidev driver, but for instance for MMC SPI +
some another device, or spi_setup() being called from an SPI-peripheral
probe method while some other device has already been probed and is being
used by a corresponding driver...
Of course I could have provided a fix affecting the DW APB SSI driver
only, for instance, by creating a mutual exclusive access to the set_cs
callback and setting/clearing only the bit responsible for the
corresponding chip-select. But after a short research I've discovered that
the problem most likely affects a lot of the other drivers:
- drivers/spi/spi-sun4i.c - RMW the chip-select register;
- drivers/spi/spi-rockchip.c - RMW the chip-select register;
- drivers/spi/spi-qup.c - RMW a generic force-CS flag in a CSR.
- drivers/spi/spi-sifive.c - set a generic CS-mode flag in a CSR.
- drivers/spi/spi-bcm63xx-hsspi.c - uses an internal mutex to serialize
the bus config changes, but still isn't protected from the race
condition described above;
- drivers/spi/spi-geni-qcom.c - RMW a chip-select internal flag and set the
CS state in HW;
- drivers/spi/spi-orion.c - RMW a chip-select register;
- drivers/spi/spi-cadence.c - RMW a chip-select register;
- drivers/spi/spi-armada-3700.c - RMW a chip-select register;
- drivers/spi/spi-lantiq-ssc.c - overwrites the chip-select register;
- drivers/spi/spi-sun6i.c - RMW a chip-select register;
- drivers/spi/spi-synquacer.c - RMW a chip-select register;
- drivers/spi/spi-altera.c - directly sets the chip-select state;
- drivers/spi/spi-omap2-mcspi.c - RMW an internally cached CS state and
writes it to HW;
- drivers/spi/spi-mt65xx.c - RMW some CSR;
- drivers/spi/spi-jcore.c - directly sets the chip-selects state;
- drivers/spi/spi-mt7621.c - RMW a chip-select register;
I could have missed some drivers, but a scale of the problem is obvious.
As you can see most of the drivers perform an unprotected
Read-modify-write chip-select register modification in the set_cs callback.
Seeing the spi_setup() function is calling the spi_set_cs() and it can be
executed concurrently with SPI-transfers exec procedure, which also calls
spi_set_cs() in the SPI core spi_transfer_one_message() method, the race
condition of the register modification turns to be obvious.
To sum up the problem denoted above affects each driver for a controller
having more than one chip-select lane and which:
1) performs the RMW to some CS-related register with no serialization;
2) directly disables any CS on spi_set_cs(dev, false).
* the later is the case of the DW APB SSI driver.
The controllers which equipped with a single CS theoretically can also
experience the problem, but in practice will not since normally the
spi_setup() isn't called concurrently with the SPI-transfers executed on
the same SPI peripheral device.
In order to generically fix the denoted bug I'd suggest to serialize an
access to the controller IO by taking the IO mutex in the spi_setup()
callback. The mutex is held while there is an SPI communication going on
on the SPI-bus of the corresponding SPI-controller. So calling the
spi_setup() method and disabling/updating the CS state within it would be
safe while there is no any SPI-transfers being executed. Also note I
suppose it would be safer to protect the spi_controller->setup() callback
invocation too, seeing some of the SPI-controller drivers update a HW
state in there.
Fixes: 49d7d695ca ("spi: dw: Explicitly de-assert CS on SPI transfer completion")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201117094517.5654-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver core ignores the return value of struct device_driver::remove
(because in general there is nothing that can be done about that). So
add a warning when an spi driver returns an error.
This simplifies the quest to make struct device_driver::remove return void.
A consequent change would be to make struct spi_driver::remove return void,
but I'm keeping this quest for later (or someone else).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20201119161604.2633521-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The eventual goal is to get rid of the callbacks in struct
device_driver. Other than not using driver callbacks there should be no
side effect of this patch.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20201119161604.2633521-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Consider an spi driver with a .probe but without a .remove callback (e.g.
rtc-ds1347). The function spi_drv_probe() is called to bind a device and
so dev_pm_domain_attach() is called. As there is no remove callback
spi_drv_remove() isn't called at unbind time however and so calling
dev_pm_domain_detach() is missed and the pm domain keeps active.
To fix this always use both spi_drv_probe() and spi_drv_remove() and
make them handle the respective callback not being set. This has the
side effect that for a (hypothetical) driver that has neither .probe nor
remove the clk and pm domain setup is done.
Fixes: 33cf00e570 ("spi: attach/detach SPI device to the ACPI power domain")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20201119161604.2633521-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak in mxs_spi_probe, so we should fix it.
Fixes: b7969caf41 ("spi: mxs: implement runtime pm")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201106012421.95420-1-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since 5.10-rc1 i.MX is a devicetree-only platform and the existing
.id_table support in this driver was only useful for old non-devicetree
platforms.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201116202606.29888-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If the calls to of_match_device(), of_alias_get_id(),
devm_ioremap_resource(), devm_regmap_init_mmio() or devm_clk_get()
fail on probe of the NPCM FIU SPI driver, the spi_controller struct is
erroneously not freed.
Fix by switching over to the new devm_spi_alloc_master() helper.
Fixes: ace55c411b ("spi: npcm-fiu: add NPCM FIU controller driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.4+: 5e844cc37a5c: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v5.4+
Cc: Tomer Maimon <tmaimon77@gmail.com>
Link: https://lore.kernel.org/r/a420c23a363a3bc9aa684c6e790c32a8af106d17.1605512876.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
It turns out the IRQs most like can be unmasked before the controller is
enabled with no problematic consequences. The manual doesn't explicitly
state that, but the examples perform the controller initialization
procedure in that order. So the commit da8f58909e ("spi: dw: Unmask IRQs
after enabling the chip") hasn't been that required as I thought. But
anyway setting the IRQs up after the chip enabling still worth adding
since it has simplified the code a bit. The problem is that it has
introduced a potential bug. The transfer handler pointer is now
initialized after the IRQs are enabled. That may and eventually will cause
an invalid or uninitialized callback invocation. Fix that just by
performing the callback initialization before the IRQ unmask procedure.
Fixes: da8f58909e ("spi: dw: Unmask IRQs after enabling the chip")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201117094054.4696-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
MT8192 spi-nor is an independent sub system, we need extra control axi
bus clock for it. Add support for the additional axi clock to allow it
to be configured appropriately.
Signed-off-by: bayi cheng <bayi.cheng@mediatek.com>
Tested-by: Ikjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/1605084902-13151-2-git-send-email-bayi.cheng@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix to return the error code from
devm_reset_control_get_optional_exclusive() instaed of 0
in cqspi_probe().
Fixes: 31fb632b5d ("spi: Move cadence-quadspi driver to drivers/spi/")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20201116141836.2970579-1-chengzhihao1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Clang warns:
drivers/spi/spi-bcm2835aux.c:532:50: warning: variable 'err' is
uninitialized when used here [-Wuninitialized]
dev_err(&pdev->dev, "could not get clk: %d\n", err);
^~~
./include/linux/dev_printk.h:112:32: note: expanded from macro 'dev_err'
_dev_err(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~
drivers/spi/spi-bcm2835aux.c:495:9: note: initialize the variable 'err'
to silence this warning
int err;
^
= 0
1 warning generated.
Restore the assignment so that the error value can be used in the
dev_err statement and there is no uninitialized memory being leaked.
Fixes: e13ee6cc47 ("spi: bcm2835aux: Fix use-after-free on unbind")
Link: https://github.com/ClangBuiltLinux/linux/issues/1199
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20201113180701.455541-1-natechancellor@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Here's my proposal to fix the use-after-free bugs reported by
Sascha Hauer and Florian Fainelli:
I scrutinized all SPI drivers in the v5.10 tree:
* There are 9 drivers with a use-after-free in the ->remove() hook
caused by accessing driver private data after spi_unregister_controller().
* There are 8 drivers which leak the spi_controller in the ->probe()
error path because of a missing spi_controller_put().
I'm introducing devm_spi_alloc_master/slave() which automatically
calls spi_controller_put() on ->remove(). This fixes both classes
of bugs while at the same time reducing code amount and complexity
in the ->probe() hook.
I propose that spi_controller_unregister() should no longer release
a reference on the spi_controller. Instead, drivers need to either
do it themselves or use one of the devm functions introduced herein.
The vast majority of drivers can be converted to the devm functions.
See the commit message of patch [1/4] for the rationale and details.
Enclosed are patches for 3 Broadcom drivers.
Patches for the other drivers are on this branch:
https://github.com/l1k/linux/commits/spi_fixes
@Florian Fainelli: Could you verify that there are no KASAN splats or
leaks with these patches? Unfortunately I do not have any SPI-capable
hardware at my disposal right now, so can only compile-test. You may
want to augment spi_controller_release() with a printk() to log when
the spi_controller is freed.
@Mark Brown: Patches [2/4] to [4/4] reference the SHA-1 of patch [1/4]
in their stable tags. Because the hash is unknown to me until you apply
the patch, I've used "123456789abc" as a placeholder. You'll have to
replace the hash if/when applying. Alternatively, only apply patch [1/4]
and I'll repost the other patches with the hash fixed up.
Thanks!
Lukas Wunner (4):
spi: Introduce device-managed SPI controller allocation
spi: bcm2835: Fix use-after-free on unbind
spi: bcm2835aux: Fix use-after-free on unbind
spi: bcm-qspi: Fix use-after-free on unbind
drivers/spi/spi-bcm-qspi.c | 34 ++++++++-------------
drivers/spi/spi-bcm2835.c | 24 +++++----------
drivers/spi/spi-bcm2835aux.c | 21 +++++--------
drivers/spi/spi.c | 58 +++++++++++++++++++++++++++++++++++-
include/linux/spi/spi.h | 19 ++++++++++++
5 files changed, 103 insertions(+), 53 deletions(-)
--
2.28.0
Normally the last reference on an spi_controller is released by
spi_unregister_controller(). In the case of the i.MX lpspi driver,
the spi_controller is registered with devm_spi_register_controller(),
so spi_unregister_controller() is invoked automatically after the driver
has unbound.
However the driver already releases the last reference in
fsl_lpspi_remove() through a gratuitous call to spi_master_put(),
causing a use-after-free when spi_unregister_controller() is
subsequently invoked by the devres framework.
Fix by dropping the superfluous spi_master_put().
Fixes: 944c01a889 ("spi: lpspi: enable runtime pm for lpspi")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.2+
Cc: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/ab3c0b18bd820501a12c85e440006e09ec0e275f.1604874488.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the calls to devm_platform_ioremap_resource(), irq_of_parse_and_map()
or devm_request_irq() fail on probe of the ST SSC4 SPI driver, the
runtime PM disable depth is incremented even though it was not
decremented before. Fix it.
Fixes: cd050abeba ("spi: st-ssc4: add missed pm_runtime_disable")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.5+
Cc: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/fbe8768c30dc829e2d77eabe7be062ca22f84024.1604874488.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the calls to devm_request_irq() or devm_spi_register_master() fail
on probe of the PIC32 SPI driver, the DMA channels requested by
pic32_spi_dma_prep() are erroneously not released. Plug the leak.
Fixes: 1bcb9f8ceb ("spi: spi-pic32: Add PIC32 SPI master driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.7+
Cc: Purna Chandra Mandal <purna.mandal@microchip.com>
Link: https://lore.kernel.org/r/9624250e3a7aa61274b38219a62375bac1def637.1604874488.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
If the calls to platform_get_irq() or devm_request_irq() fail on probe
of the SynQuacer SPI driver, the clock "sspi->clk" is erroneously not
unprepared and disabled.
If the clock rate "master->max_speed_hz" cannot be determined, the same
happens and in addition the spi_master struct is not freed.
Fix it.
Fixes: b0823ee35c ("spi: Add spi driver for Socionext SynQuacer platform")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v5.3+
Cc: Masahisa Kojima <masahisa.kojima@linaro.org>
Link: https://lore.kernel.org/r/232281df1ab91d8f0f553a62d5f97fc264ace4da.1604874488.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
David Bauer