PA Layer issues a LINERESET to the PHY at the recovery step in the Power
Mode change operation. If it happens during auto or manual hibern8 enter,
even if hibern8 enter succeeds, UFS power mode shall be set to PWM-G1 mode
and kept in that mode after exit from hibern8, leading to bad performance.
Handle the LINERESET in the eh_work by restoring power mode to HS mode
after all pending reqs and tasks are cleared from doorbell.
Link: https://lore.kernel.org/r/1598321228-21093-3-git-send-email-cang@codeaurora.org
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To recover non-fatal errors, no full reset is required, err_handler only
clears those pending TRs/TMRs so that SCSI layer can re-issue them. In
current err_handler, TRs are directly cleared from UFS host's doorbell but
not aborted from device side. However, according to the UFSHCI JEDEC spec,
the host software shall use UTP Transfer Request List Clear Register to
clear a task from UFS host's doorbell only when a UTP Transfer Request is
expected to not be completed, e.g. when the host software receives a
“FUNCTION COMPLETE” Task Management response which means a Transfer Request
was aborted. To follow the UFSHCI JEDEC spec, in err_handler, abort one TR
before clearing it from doorbell.
Link: https://lore.kernel.org/r/1598321228-21093-2-git-send-email-cang@codeaurora.org
Acked-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix ufshcd_print_trs() to consider UFSHCD_QUIRK_PRDT_BYTE_GRAN when using
utp_transfer_req_desc::prd_table_length, so that it doesn't treat the
number of bytes as the number of entries.
Originally from Kiwoong Kim
(https://lkml.kernel.org/r/20200218233115.8185-1-kwmad.kim@samsung.com).
Link: https://lore.kernel.org/r/20200826021040.152148-1-ebiggers@kernel.org
Fixes: 26f968d7de ("scsi: ufs: Introduce UFSHCD_QUIRK_PRDT_BYTE_GRAN quirk")
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We have two knobs to control flush for write booster,
fWriteBoosterBufferFlushDuringHibernate and fWriteBoosterBufferFlushEn.
Some vendors use only fWriteBoosterBufferFlushDuringHibernate because this
can reportedly cover most scenarios. Also, there have been some reports
that flush by fWriteBoosterBufferFlushEn could lead to increased power
consumption thanks to unexpected internal operations. Consequently, we need
a way to enable or disable fWriteBoosterEn operations. Add quirk to bypass
manual flush.
Link: https://lore.kernel.org/r/ffdb0eda30515809f0ad9ee936b26917ee9b4593.1598319701.git.kwmad.kim@samsung.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 5586dd8ea2 ("scsi: ufs: Fix a race condition between error handler
and runtime PM ops") moves the ufshcd_scsi_block_requests() inside
err_handler() but forgets to remove the ufshcd_scsi_unblock_requests() in
the early return path. Correct the mistake.
Link: https://lore.kernel.org/r/1597798958-24322-1-git-send-email-cang@codeaurora.org
Fixes: 5586dd8ea2 ("scsi: ufs: Fix a race condition between error handler and runtime PM ops")
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Hongwu Su<hongwus@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, the UFS driver busy waits for fDeviceInit to be cleared. Provide
an upper bound and sleep between attempts instead of busy waiting.
Link: https://lore.kernel.org/r/1597053747-75171-1-git-send-email-kwmad.kim@samsung.com
Tested-by: Kiwoong Kim <kwmad.kim@samsung.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20200814095034.20709-3-huobean@gmail.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ufshcd_comp_devman_upiu() was poorly named leading people to think it was a
completion function. Rename it to ufshcd_compose_devman_upiu().
Link: https://lore.kernel.org/r/20200814095034.20709-2-huobean@gmail.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In current UFS task abort hook, namely ufshcd_abort(), if one task is
aborted successfully, clk_gating.active_reqs held by this task is not
decreased, which makes clk_gating.active_reqs stay above zero forever, thus
clock gating would never happen. Instead of releasing resources of one task
"manually", use the existing func __ufshcd_transfer_req_compl(). This
change also eliminates a possible race of scsi_dma_unmap() from the real
completion in IRQ handler path.
Link: https://lore.kernel.org/r/1596975355-39813-10-git-send-email-cang@codeaurora.org
Fixes: 1ab27c9cf8 ("ufs: Add support for clock gating")
CC: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the bit corresponding to a task in the Doorbell register has been
cleared, no need to poll the status of the task on the device side and to
send an Abort Task TM. Instead, let it directly goto cleanup.
In addition, to keep original debug output, move the goto below the debug
print.
Link: https://lore.kernel.org/r/20200811141859.27399-3-huobean@gmail.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If somehow no interrupt notification is raised for a completed request and
its doorbell bit is cleared by host, UFS driver needs to cleanup its
outstanding bit in ufshcd_abort(). Otherwise, system may behave abnormally
in the following scenario:
After ufshcd_abort() returns, this request will be requeued by SCSI layer
with its outstanding bit set. Any future completed request will trigger
ufshcd_transfer_req_compl() to handle all "completed outstanding bits". At
this time the "abnormal outstanding bit" will be detected and the "requeued
request" will be chosen to execute request post-processing flow. This is
wrong because this request is still "alive".
Link: https://lore.kernel.org/r/20200811141859.27399-2-huobean@gmail.com
Reviewed-by: Can Guo <cang@codeaurora.org>
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For shared interrupts, the interrupt status might be zero, so check that
first.
Link: https://lore.kernel.org/r/20200811133936.19171-2-adrian.hunter@intel.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The interrupt might be shared, in which case it is not an error for the
interrupt handler to be called when the interrupt status is zero, so don't
print the message unless there was enabled interrupt status.
Link: https://lore.kernel.org/r/20200811133936.19171-1-adrian.hunter@intel.com
Fixes: 9333d77573 ("scsi: ufs: Fix irq return code")
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In ufshcd_suspend(), after clk-gating is suspended and link is set
as Hibern8 state, ufshcd_hold() is still possibly invoked before
ufshcd_suspend() returns. For example, MediaTek's suspend vops may
issue UIC commands which would call ufshcd_hold() during the command
issuing flow.
Now if UFSHCD_CAP_HIBERN8_WITH_CLK_GATING capability is enabled,
then ufshcd_hold() may enter infinite loops because there is no
clk-ungating work scheduled or pending. In this case, ufshcd_hold()
shall just bypass, and keep the link as Hibern8 state.
Link: https://lore.kernel.org/r/20200809050734.18740-1-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Co-developed-by: Andy Teng <andy.teng@mediatek.com>
Signed-off-by: Andy Teng <andy.teng@mediatek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current IRQ handler blocks SCSI requests before scheduling eh_work,
when error handler calls pm_runtime_get_sync, if ufshcd_suspend/resume
sends a SCSI cmd, most likely the SSU cmd, since SCSI requests are blocked,
pm_runtime_get_sync() will never return because ufshcd_suspend/resume is
blocked by the SCSI cmd.
- In queuecommand path, hba->ufshcd_state check and ufshcd_send_command
should stay under the same spin lock. This is to make sure that no more
commands leak into doorbell after hba->ufshcd_state is changed.
- Don't block SCSI requests before error handler starts to run, let error
handler block SCSI requests when it is ready to start error recovery.
- Don't let SCSI layer keep requeuing the SCSI cmds sent from HBA runtime
PM ops, let them pass or fail them. Let them pass if eh_work is
scheduled due to non-fatal errors. Fail them if eh_work is scheduled due
to fatal errors, otherwise the cmds may eventually time out since UFS is
in bad state, which gets error handler blocked for too long. If we fail
the SCSI cmds sent from HBA runtime PM ops, HBA runtime PM ops fails
too, but it does not hurt since error handler can recover HBA runtime PM
error.
Link: https://lore.kernel.org/r/1596975355-39813-9-git-send-email-cang@codeaurora.org
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Performing dumps in the IRQ handler causes system stability issues. Move
dumps to the error handler and only print basic host registers here.
Link: https://lore.kernel.org/r/1596975355-39813-8-git-send-email-cang@codeaurora.org
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current error handler can not recover HBA runtime PM error if
ufshcd_suspend/resume has failed due to UFS errors, e.g. hibern8 enter/exit
error or SSU cmd error. When this happens, error handler may fail
performing a full reset and restore because error handler always assumes
that power, IRQs and clocks are ready after pm_runtime_get_sync returns,
but actually they are not if ufshcd_resume fails[1].
If ufschd_suspend/resume fails due to UFS errors, runtime PM framework
saves the error value to dev.power.runtime_error. After that, HBA dev
runtime suspend/resume would not be invoked anymore unless runtime_error is
cleared[2].
In case of ufshcd_suspend/resume fails due to UFS errors, for scenario [1],
error handler cannot assume anything of pm_runtime_get_sync, meaning error
handler should explicitly turn ON powers, IRQs and clocks again. To get the
HBA runtime PM work as regard for scenario [2], error handler can clear the
runtime_error by calling pm_runtime_set_active() if full reset and restore
succeeds. And, more important, if pm_runtime_set_active() returns no error,
which means runtime_error has been cleared, we also need to resume those
scsi devices under HBA in case any of them has failed to be resumed due to
HBA runtime resume failure. This is to unblock blk_queue_enter in case
there are bios waiting inside it.
Link: https://lore.kernel.org/r/1596975355-39813-7-git-send-email-cang@codeaurora.org
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Error recovery can be invoked from multiple code paths, including hibern8
enter/exit (from ufshcd_link_recovery), ufshcd_eh_host_reset_handler() and
eh_work scheduled from IRQ context. Ultimately, these paths are all trying
to invoke ufshcd_reset_and_restore() in either a synchronous or
asynchronous manner. This causes problems:
- If link recovery happens during ungate work, ufshcd_hold() would be
called recursively. Although commit 53c12d0ef6 ("scsi: ufs: fix error
recovery after the hibern8 exit failure") fixed a deadlock due to
recursive calls of ufshcd_hold() by adding a check of eh_in_progress
into ufshcd_hold, this check allows eh_work to run in parallel while
link recovery is running.
- Similar concurrency can also happen when error recovery is invoked from
ufshcd_eh_host_reset_handler and ufshcd_link_recovery.
- Concurrency can even happen between eh_works. eh_work, currently queued
on system_wq, is allowed to have multiple instances running in parallel,
but we don't have proper protection for that.
If any of above concurrency scenarios happen, error recovery would fail and
lead ufs device and host into bad states. To fix the concurrency problem,
this change queues eh_work on a single threaded workqueue and removes link
recovery calls from the hibern8 enter/exit path. In addition, make use of
eh_work in eh_host_reset_handler instead of calling
ufshcd_reset_and_restore. This unifies the UFS error recovery mechanism.
According to the UFSHCI JEDEC spec, hibern8 enter/exit error occurs when
the link is broken. This essentially applies to any power mode change
operations (since they all use PACP_PWR cmds in UniPro layer). So, if a
power mode change operation (including AH8 enter/exit) fails, mark link
state as UIC_LINK_BROKEN_STATE and schedule the eh_work. In this case,
error handler needs to do a full reset and restore to recover the link back
to active. Before the link state is recovered to active,
ufshcd_uic_pwr_ctrl simply returns -ENOLINK to avoid more errors.
Link: https://lore.kernel.org/r/1596975355-39813-6-git-send-email-cang@codeaurora.org
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Information about the last interrupt status and timestamp is helpful when
debugging system stability issues (IRQ starvation, for instance). Add this
information to ufshcd_print_host_state() output.
In addition, UFS device information such as model name and firmware version
also comes in handy during debugging. This is printed as well.
Link: https://lore.kernel.org/r/1596975355-39813-5-git-send-email-cang@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Hongwu Su <hongwus@codeaurora.org>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clock gating can be turned on/off selectively which means the associated
state information is only correct if the feature is enabled. This change
makes sure that we only look at state of clk-gating if it is enabled.
Link: https://lore.kernel.org/r/1596975355-39813-2-git-send-email-cang@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Hongwu Su <hongwus@codeaurora.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS devices require delay after VCC power rail is turned off.
Introduce a device quirk "DELAY_AFTER_LPM" to add 5ms delay after VCC
power-off during suspend flow.
Link: https://lore.kernel.org/r/20200729051840.31318-2-stanley.chu@mediatek.com
Reviewed-by: Andy Teng <andy.teng@mediatek.com>
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add missing setup_xfer_req() call in ufshcd_issue_devman_upiu_cmd() in
ufs-bsg path. Relocate existing setup_xfer_req() calls to a common place,
i.e., ufshcd_send_command(), to simplify the driver.
Link: https://lore.kernel.org/r/20200706060707.32608-3-stanley.chu@mediatek.com
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Simplify recording command completion time in __ufshcd_transfer_req_compl()
by assigning lrbp->compl_time_stamp in a unified location.
Link: https://lore.kernel.org/r/20200706060707.32608-2-stanley.chu@mediatek.com
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Wire up ufshcd.c with the UFS Crypto API, the block layer inline encryption
additions and the keyslot manager.
Many existing inline crypto devices require some additional behaviour not
specified in the UFSHCI v2.1 specification - as such the vendor specific
drivers will need to be updated where necessary to make it possible to use
those devices. Some of these changes have already been proposed upstream,
such as for the Qualcomm 845 SoC at
https://lkml.kernel.org/linux-scsi/20200501045111.665881-1-ebiggers@kernel.org/
and for ufs-mediatek at
https://lkml.kernel.org/linux-scsi/20200304022101.14165-1-stanley.chu@mediatek.com/
This patch has been tested on the db845c, sm8150-mtp and sm8250-mtp
(which have Qualcomm chipsets) and on some mediatek chipsets using these
aforementioned vendor specific driver updates.
Link: https://lore.kernel.org/r/20200706200414.2027450-4-satyat@google.com
Reviewed-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Satya Tangirala <satyat@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the crypto registers and structs defined in v2.1 of the JEDEC UFSHCI
specification in preparation to add support for inline encryption to UFS.
Link: https://lore.kernel.org/r/20200706200414.2027450-2-satyat@google.com
Reviewed-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Satya Tangirala <satyat@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to the UFS Spec, the Flags field in the UPIU is one byte in size,
not 4. Change it to be u8.
Link: https://lore.kernel.org/r/20200706123936.24799-1-huobean@gmail.com
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a UFS device is not qualified to use WriteBooster, either due to wrong
UFS version or device-specific quirks, then the capability in host shall be
disabled to prevent any WriteBooster operations in the future.
Link: https://lore.kernel.org/r/20200625030430.25048-1-stanley.chu@mediatek.com
Fixes: 3d17b9b5ab ("scsi: ufs: Add write booster feature support")
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The UFS load calculation is based on "total_time" and "busy_time" in a
devfreq window. However, the source of time is different for both
parameters: "busy_time" is assigned from "jiffies" thus has different
accuracy from "total_time" which is assigned from ktime_get().
In addition, the time of window boundary is not exactly the same as the
starting busy time in this window if UFS is actually busy in the beginning
of the window. A similar accuracy error may also happen for the end of busy
time in current window.
To guarantee the precision of load calculation, we need to
1. Align time accuracy of both devfreq_dev_status.total_time and
devfreq_dev_status.busy_time. For example, use "ktime_get()" directly.
2. Align the following timelines:
- The beginning time of devfreq windows
- The beginning of busy time in a new window
- The end of busy time in the current window
Link: https://lore.kernel.org/r/20200611101043.6379-1-stanley.chu@mediatek.com
Fixes: a3cd5ec55f ("scsi: ufs: add load based scaling of UFS gear")
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clean up the following items:
- Sort vendor names in alphabetical order
- Squash quirks as compact as possible in device table to enhance
performance of the lookup
- Sort device quirks in alphabetical order
Link: https://lore.kernel.org/r/20200612012625.6615-3-stanley.chu@mediatek.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is confirmed that Micron device needs DELAY_BEFORE_LPM quirk to have a
delay before VCC is powered off. Sdd Micron vendor ID and this quirk for
Micron devices.
Link: https://lore.kernel.org/r/20200612012625.6615-2-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add SPDX GPL-2.0 to UFS driver files that specified the GPL version 2
license, remove the full boilerplate text.
Link: https://lore.kernel.org/r/20200605200520.20831-2-huobean@gmail.com
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For UFS 3.1, the normal unit descriptor is 10 bytes larger than the RPMB
unit. However, both descriptors share the same desc_idn, to cover both unit
descriptors with one length, we choose the normal unit descriptor length by
desc_index.
Link: https://lore.kernel.org/r/20200603091959.27618-6-huobean@gmail.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
At UFS initialization stage, to get the length of the descriptor,
ufshcd_read_desc_length() was being called 6 times. Instead, we will
capture the descriptor size the first time we'll read it.
Delete unnecessary redundant code, remove ufshcd_read_desc_length(),
ufshcd_init_desc_sizes(), and boost UFS initialization.
Link: https://lore.kernel.org/r/20200603091959.27618-5-huobean@gmail.com
Acked-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bart van Assche <bvanassche@acm.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If param_offset is not 0, the memcpy length shouldn't be the true
descriptor length.
Link: https://lore.kernel.org/r/20200603091959.27618-4-huobean@gmail.com
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For the UFS device, the maximum descriptor size is 255, max_t called on
ufs_get_device_desc() is useless.
Link: https://lore.kernel.org/r/20200603091959.27618-2-huobean@gmail.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bart van Assche <bvanassche@acm.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some controller like Exynos determines if FATAL ERROR (0x7) in OCS field in
UTRD occurs for values other than GOOD (0x0) in STATUS field in response
upiu as well as errors that a host controller can't cover. This patch is
to prevent from reporting command results in those cases.
Link: https://lore.kernel.org/r/20200528011658.71590-6-alim.akhtar@samsung.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS host controllers like Exynos uses granularities of PRDT length and
offset as bytes, whereas others use actual segment count.
Link: https://lore.kernel.org/r/20200528011658.71590-5-alim.akhtar@samsung.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some host controllers don't support host controller enable via HCE.
Link: https://lore.kernel.org/r/20200528011658.71590-4-alim.akhtar@samsung.com
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some host controllers support interrupt aggregation but don't allow
resetting counter and timer in software.
Link: https://lore.kernel.org/r/20200528011658.71590-3-alim.akhtar@samsung.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With the correct behavior, setting the bit to '0' indicates clear and '1'
indicates no change. If host controller handles this the other way around,
UFSHCI_QUIRK_BROKEN_REQ_LIST_CLR can be used.
Link: https://lore.kernel.org/r/20200528011658.71590-2-alim.akhtar@samsung.com
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In ufshcd_probe_hba(), all BKOP SW tracking variables can be reset together
in ufshcd_force_reset_auto_bkops(), thus urgent_bkop_lvl initialization in
the beginning of ufshcd_probe_hba() can be merged into
ufshcd_force_reset_auto_bkops().
Link: https://lore.kernel.org/r/20200530141200.4616-1-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Urgent bkops level is used to compare against actual bkops status read from
UFS device. Urgent bkops level is set during initialization and might be
updated in exception event handler during runtime. But it should not be
updated to the actual bkops status every time when auto bkops is toggled.
Otherwise, if urgent bkops level is updated to 0, auto bkops shall always
be kept enabled.
Link: https://lore.kernel.org/r/1590632686-17866-1-git-send-email-cang@codeaurora.org
Fixes: 24366c2afb ("scsi: ufs: Recheck bkops level if bkops is disabled")
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently UFS host driver promises VCC supply if UFS device needs to do
WriteBooster flush during runtime suspend.
However the UFS specification mentions:
"While the flushing operation is in progress, the device is in Active power
mode."
Therefore UFS host driver needs to promise more: Keep UFS device as "Active
power mode", otherwise UFS device shall not do any flush if device enters
Sleep or PowerDown power mode. Similarly, the same promises shall be
applied if device needs urgent BKOP during runtime suspend.
Fix this by not changing device power mode if WriteBooster flush or urgent
BKOP is required in ufshcd_suspend().
Now, if device finishes its job but is not resumed for a very long time,
system will have unnecessary power drain because VCC is still supplied. A
method to re-check the threshold of keeping VCC supply is required to fix
the power drain. However, the threshold re-check needs to re-activate the
link first because the decision depends on the latest device status.
Also introduce a delayed work to force runtime resume after a certain delay
during runtime suspend. This makes threshold re-check happen natually in
the entry of the next runtime-suspend. The device can continue its
WriteBooster flush or urgent BKOP jobs soon after resumed if device has no
upcoming requests and link enters hibern8 state either by Auto-Hibern8 or
hibern8 during clk-gating scheme. This solution not only prevents power
drain but also makes as much use of time as possible for device's
background jobs.
Link: https://lore.kernel.org/r/20200522083212.4008-5-stanley.chu@mediatek.com
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For WriteBooster feature related attributes, the index used by query shall
be LUN ID if LU Dedicated buffer mode is enabled.
Link: https://lore.kernel.org/r/20200522083212.4008-4-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to the UFS specification, WriteBooster is officially supported by
UFS 2.2.
Since UFS 2.2 specification has been finalized in JEDEC and such devices
have also showed up in the market, modify the checking rule for
ufshcd_wb_probe() to allow these devices to enable WriteBooster.
Link: https://lore.kernel.org/r/20200522083212.4008-3-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The whole UFS host instance has been zero-initialized by scsi_host_alloc(),
thus UFS driver does not need to clear "dev_info" member specifically in
ufshcd_device_params_init().
Simply remove the unnecessary code.
Link: https://lore.kernel.org/r/20200522083212.4008-2-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ufshcd_wait_for_register() function either sleeps or spins until the
specified register has reached the desired value. Busy-waiting is not only
considered a bad practice but also has a bad impact on energy
consumption. Always sleep instead of spinning by making sure that all
ufshcd_wait_for_register() calls happen from a context where it is allowed
to sleep. The only function call that has to be moved is the
ufshcd_hba_stop() call in ufshcd_host_reset_and_restore().
Link: https://lore.kernel.org/r/20200507222750.19113-1-bvanassche@acm.org
Cc: Can Guo <cang@codeaurora.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Asutosh Das <asutoshd@codeaurora.org>
Tested-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow flush threshold for WriteBooster to be customizable by vendors. To
achieve this, make the value a variable in struct ufs_hba_variant_params.
Also introduce UFS_WB_BUF_REMAIN_PERCENT() macro to provide a more flexible
way to specify WriteBooster available buffer values.
Link: https://lore.kernel.org/r/20200509093716.21010-4-stanley.chu@mediatek.com
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The UFS driver is growing more and more customizable parameters. Collect
them in one place.
Link: https://lore.kernel.org/r/20200509093716.21010-2-stanley.chu@mediatek.com
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Small cleanup as below items,
1. Use ufshcd_is_wb_allowed() directly instead of ufshcd_wb_sup() since
ufshcd_wb_sup() just returns the result of ufshcd_is_wb_allowed().
2. In ufshcd_suspend(), "else if (!ufshcd_is_runtime_pm(pm_op)) can be
simplified to "else" since both have the same meaning.
This patch does not change any functionality.
Link: https://lore.kernel.org/r/20200508080115.24233-9-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to UFS specification, there are two WriteBooster mode of
operations: "LU dedicated buffer" mode and "shared buffer" mode. In the
"LU dedicated buffer" mode, the WriteBooster Buffer is dedicated to a
logical unit.
If the device supports the "LU dedicated buffer" mode, this mode is
configured by setting bWriteBoosterBufferType to 00h. The logical unit
WriteBooster Buffer size is configured by setting the
dLUNumWriteBoosterBufferAllocUnits field of the related Unit
Descriptor. Only a value greater than zero enables the WriteBooster feature
in the logical unit.
Modify ufshcd_wb_probe() as above description to support LU Dedicated
buffer mode.
Note that according to UFS 3.1 specification, the valid value of
bDeviceMaxWriteBoosterLUs parameter in Geometry Descriptor is 1, which
means at most one LUN can have WriteBooster buffer in "LU dedicated buffer
mode". Therefore this patch supports only one LUN with WriteBooster
enabled. All WriteBooster related sysfs nodes are specifically mapped to
the LUN with WriteBooster enabled in LU Dedicated buffer mode.
Link: https://lore.kernel.org/r/20200508080115.24233-7-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For preparation of LU Dedicated buffer mode support on WriteBooster
feature, "index" parameter shall be added and allowed to be specified by
callers.
Link: https://lore.kernel.org/r/20200508080115.24233-6-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Export ufs_fixup_device_setup() to allow vendors to re-use it for fixing
device quriks on specified UFS hosts.
Link: https://lore.kernel.org/r/20200508080115.24233-4-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS deivces may have required device quirks or have non-standard
features which are enabled only on specified UFS hosts or for special
customers.
To not "pollute" common device quirk list, i.e. ufs_fixups table, for those
devices mentioned above, introduce "fixup_dev_quirks" vops to allow vendors
to fix or modify device quirks accordingly.
Link: https://lore.kernel.org/r/20200508080115.24233-3-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The WriteBooster feature can be supported by some pre-3.1 UFS devices by
upgrading firmware.
To enable WriteBooster feature in such devices, introduce a device quirk to
relax the entrance condition of ufshcd_wb_probe() to allow host driver to
check those devices' WriteBooster capability.
WriteBooster feature can be available if below all conditions are
satisfied,
1. Host enables WriteBooster capability
2. UFS 3.1 device or UFS pre-3.1 device with quirk
UFS_DEVICE_QUIRK_SUPPORT_EXTENDED_FEATURES enabled
3. The device descriptor shall have DEVICE_DESC_PARAM_EXT_UFS_FEATURE_SUP
field
4. WriteBooster support is specified in above field
Link: https://lore.kernel.org/r/20200508080115.24233-2-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current codebase makes use of the zero-length array language extension
to the C90 standard, but the preferred mechanism to declare variable-length
types such as these ones is a flexible array member[1][2], introduced in
C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning in
case the flexible array does not occur last in the structure, which will
help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by this
change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in which
the sizeof operator is being incorrectly/erroneously applied to zero-length
arrays and the result is zero. Such instances may be hiding some bugs. So,
this work (flexible-array member conversions) will also help to get
completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Link: https://lore.kernel.org/r/20200507192550.GA16683@embeddedor
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The write performance of TLC NAND is considerably lower than SLC NAND.
Using SLC NAND as a WriteBooster Buffer enables the write request to be
processed with lower latency and improves the overall write performance.
Adds support for shared-buffer mode WriteBooster.
WriteBooster enable: SW enables it when clocks are scaled up, thus it's
enabled only in high load conditions.
WriteBooster disable: SW will disable the feature, when clocks are scaled
down. Thus writes would go as normal writes.
To keep the endurance of the WriteBooster Buffer at a maximum, this
load-based toggling is adopted.
Link: https://lore.kernel.org/r/2871444d9083b0e9323ef6d8ff1b544b7784adc9.1587591527.git.asutoshd@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following coccicheck warning:
drivers/scsi/ufs/ufshcd.c:4140:6-14: WARNING: Assignment of 0/1 to bool
variable.
Link: https://lore.kernel.org/r/20200426094305.24083-1-yanaijie@huawei.com
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During suspend, if the link is put to off, it would require a full
initialization during resume. This patch resets and restores both the host
and the card during initialization, otherwise host-only reset and restore
would fail occasionally.
Link: https://lore.kernel.org/r/1586844892-22720-1-git-send-email-cang@codeaurora.org
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Stanley Chu <stanley.chu@mediatek.com>
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is a batch of changes that didn't make it in the initial pull
request because the lpfc series had to be rebased to redo an incorrect
split. It's basically driver updates to lpfc, target, bnx2fc and ufs
with the rest being minor updates except the sr_block_release one
which fixes a use after free introduced by the removal of the global
mutex in the first patch set.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXpC3hSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishRTaAP9umhxu
8rRnJ5hsxXRmxOUzO5BGe403ffcBeAiEKQ2n3gEAjeoxZAaqKuDDDRfXyRnBpt9Z
QuBrgpm1gdXrJT5DDj4=
=+4Qg
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is a batch of changes that didn't make it in the initial pull
request because the lpfc series had to be rebased to redo an incorrect
split.
It's basically driver updates to lpfc, target, bnx2fc and ufs with the
rest being minor updates except the sr_block_release one which fixes a
use after free introduced by the removal of the global mutex in the
first patch set"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (35 commits)
scsi: core: Add DID_ALLOC_FAILURE and DID_MEDIUM_ERROR to hostbyte_table
scsi: ufs: Use ufshcd_config_pwr_mode() when scaling gear
scsi: bnx2fc: fix boolreturn.cocci warnings
scsi: zfcp: use fallthrough;
scsi: aacraid: do not overwrite retval in aac_reset_adapter()
scsi: sr: Fix sr_block_release()
scsi: aic7xxx: Remove more FreeBSD-specific code
scsi: mpt3sas: Fix kernel panic observed on soft HBA unplug
scsi: ufs: set device as active power mode after resetting device
scsi: iscsi: Report unbind session event when the target has been removed
scsi: lpfc: Change default SCSI LUN QD to 64
scsi: libfc: rport state move to PLOGI if all PRLI retry exhausted
scsi: libfc: If PRLI rejected, move rport to PLOGI state
scsi: bnx2fc: Update the driver version to 2.12.13
scsi: bnx2fc: Fix SCSI command completion after cleanup is posted
scsi: bnx2fc: Process the RQE with CQE in interrupt context
scsi: target: use the stack for XCOPY passthrough cmds
scsi: target: increase XCOPY I/O size
scsi: target: avoid per-loop XCOPY buffer allocations
scsi: target: drop xcopy DISK BLOCK LENGTH debug
...
update changing all our txt files to rst ones. Excluding that, we
have the usual driver updates (qla2xxx, ufs, lpfc, zfcp, ibmvfc,
pm80xx, aacraid), a treewide update for scnprintf and some other minor
updates. The major core update is Hannes moving functions out of the
aacraid driver and into the core.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXoYKiyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishSasAP4iGwSB
Y8tFaZgWadu76+wj5MdqTBoXdhnIuFF0rZG3pQEAiIKdsfQlbSFdm75+gUtx5hG/
GOilX/pJczTRJDCGNis=
=g7Sk
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This series has a huge amount of churn because it pulls in Mauro's doc
update changing all our txt files to rst ones.
Excluding that, we have the usual driver updates (qla2xxx, ufs, lpfc,
zfcp, ibmvfc, pm80xx, aacraid), a treewide update for scnprintf and
some other minor updates.
The major core change is Hannes moving functions out of the aacraid
driver and into the core"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (223 commits)
scsi: aic7xxx: aic97xx: Remove FreeBSD-specific code
scsi: ufs: Do not rely on prefetched data
scsi: dc395x: remove dc395x_bios_param
scsi: libiscsi: Fix error count for active session
scsi: hpsa: correct race condition in offload enabled
scsi: message: fusion: Replace zero-length array with flexible-array member
scsi: qedi: Add PCI shutdown handler support
scsi: qedi: Add MFW error recovery process
scsi: ufs: Enable block layer runtime PM for well-known logical units
scsi: ufs-qcom: Override devfreq parameters
scsi: ufshcd: Let vendor override devfreq parameters
scsi: ufshcd: Update the set frequency to devfreq
scsi: ufs: Resume ufs host before accessing ufs device
scsi: ufs-mediatek: customize the delay for enabling host
scsi: ufs: make HCE polling more compact to improve initialization latency
scsi: ufs: allow custom delay prior to host enabling
scsi: ufs-mediatek: use common delay function
scsi: ufs: introduce common and flexible delay function
scsi: ufs: use an enum for host capabilities
scsi: ufs: fix uninitialized tx_lanes in ufshcd_disable_tx_lcc()
...
When scaling gear, use ufshcd_config_pwr_mode() instead of
ufshcd_change_power_mode() so that vops_pwr_change_notify(PRE_CHANGE)
can be utilized to allow vendors use customized settings before
changing power mode.
Link: https://lore.kernel.org/r/1581485910-8307-2-git-send-email-cang@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently ufshcd driver assumes that bInitPowerMode parameter is not
changed by any vendors thus device power mode can be set as "Active" during
initialization.
According to UFS JEDEC specification, device power mode shall be "Active"
after HW Reset is triggered if the bInitPowerMode parameter in Device
Descriptor is default value.
By above description, we can set device power mode as "Active" after device
reset is triggered by vendor's callback. With this change, the link startup
performance can be improved in some cases by not setting link_startup_again
as true in ufshcd_link_startup().
Link: https://lore.kernel.org/r/20200327095835.10293-1-stanley.chu@mediatek.com
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Export ufshcd_link_recovery to allow vendors to recover failed link in
vendor's callbacks.
Link: https://lore.kernel.org/r/20200327095329.10083-2-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This change introduces a func ufshcd_set_clk_freq() to explicitly set clock
frequency so that it can be used in reset_and_restore path and in
ufshcd_scale_clks(). This change also cleans up the clock scaling error out
path.
[mkp: commit desc]
Link: https://lore.kernel.org/r/1585214742-5466-2-git-send-email-cang@codeaurora.org
Fixes: a3cd5ec55f ("scsi: ufs: add load based scaling of UFS gear")
Reviewed-by: Bean Huo <beanhuo@micron.com>
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We were setting bActiveICCLevel attribute for UFS device only once but the
type of this attribute has changed from persistent to volatile since UFS
device specification v2.1. This attribute is set to the default value after
power cycle or hardware reset event. It isn't safe to rely on prefetched
data (only used for bActiveICCLevel attribute now). Hence this change
removes the code related to data prefetching and set this parameter on
every attempt to probe the UFS device.
Tested-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Block layer RPM is enabled for the genernal UFS SCSI devices when they are
probed by their driver. However block layer RPM is not enabled for UFS
well-known SCSI devices.
As UFS SCSI devices have their corresponding BSG char devices, accessing a
BSG char device via IOCTL may send requests to its corresponding SCSI
device through its request queue. If BSG IOCTL sends a request to a
well-known SCSI device when HBA is not runtime active, due to block layer
RPM not being enabled for the well-known SCSI devices, the HBA, which is at
the top of a SCSI device's parent chain, will not be resumed.
This change enables block layer RPM for the well-known SCSI devices so that
block layer can handle RPM for the well-known SCSI devices just like for
the general SCSI devices.
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, the frequency that devfreq provides the driver always leads the
clocks to be scaled up. Hence, round the clock-rate to the nearest
frequency before deciding to scale.
Also update the devfreq statistics of current frequency.
Link: https://lore.kernel.org/r/d0c6c22455811e9f0eda01f9bc70d1398b51b2bd.1585160616.git.asutoshd@codeaurora.org
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reduce the waiting period between each HCE (Host Controller Enable) polling
from 5 ms to 1 ms. Also increase the maximum polling times to make "total
polling time" roughly the same.
This change could make HCE initialization faster to improve latency of
ufshcd initialization, error recovery, and resume behaviors.
Link: https://lore.kernel.org/r/20200318104016.28049-7-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently a 1 ms delay is applied before polling CONTROLLER_ENABLE
bit. This delay may not be required or can be changed in different
controllers. Make the delay as a changeable value in struct ufs_hba to
allow it customized by vendors.
Link: https://lore.kernel.org/r/20200318104016.28049-6-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce a common delay function to provide flexible way for users to take
choices of udelay and usleep_range into consideration according to the
required delay time.
Link: https://lore.kernel.org/r/20200318104016.28049-4-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In ufshcd_disable_tx_lcc(), if ufshcd_dme_get() or ufshcd_dme_peer_get()
get fail, uninitialized variable "tx_lanes" may be used as unexpected lane
ID for DME configuration.
Fix this issue by initializing "tx_lanes".
Link: https://lore.kernel.org/r/20200318104016.28049-2-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Before access auto hibner8 timer register, make sure power and clock are
properly configured to avoid unclocked register access.
Link: https://lore.kernel.org/r/1583398391-14273-1-git-send-email-cang@codeaurora.org
Fixes: ba7af5ec51 ("scsi: ufs: export ufshcd_auto_hibern8_update for vendor usage")
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lrbp->cmd is set only for SCSI commands. Use this knowledge to simplify two
boolean expressions.
Link: https://lore.kernel.org/r/20200123035637.21848-4-bvanassche@acm.org
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality but makes the next patch in
this series easier to read.
Link: https://lore.kernel.org/r/20200123035637.21848-3-bvanassche@acm.org
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently ufshcd_vops_apply_dev_quirks() comes after all UniPro parameters
have been tuned. Move it up so that vendors have a chance to apply device
quirks in advance.
Link: https://lore.kernel.org/r/1582517363-11536-2-git-send-email-cang@codeaurora.org
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove various quirks that don't have users, as well as the dead code keyed
off them.
Link: https://lore.kernel.org/r/20200221140812.476338-2-hch@lst.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In UFS version 3.0, a newly added attribute bRefClkGatingWaitTime defines
the minimum time for which the reference clock is required by device during
transition to LS-MODE or HIBERN8 state. Make this change to reflect the new
requirement by adding delays before turning off the clock.
Link: https://lore.kernel.org/r/1581392451-28743-7-git-send-email-cang@codeaurora.org
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The async version of ufshcd_hold(async == true), which is only called in
queuecommand path as for now, is expected to work in atomic context, thus
it should not sleep or schedule out. When it runs into the condition that
clocks are ON but link is still in hibern8 state, it should bail out
without flushing the clock ungate work.
Fixes: f2a785ac23 ("scsi: ufshcd: Fix race between clk scaling and ungate work")
Link: https://lore.kernel.org/r/1581392451-28743-6-git-send-email-cang@codeaurora.org
Reviewed-by: Hongwu Su <hongwus@codeaurora.org>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The functionality of vendor specific ops should be handled properly in
platform specific driver, but should not count on the UFS driver.
Link: https://lore.kernel.org/r/1581392451-28743-5-git-send-email-cang@codeaurora.org
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This sequence change is required to avoid dips in voltage during boot-up.
Apparently, this dip is caused because in the original sequence, the
regulators are initialized in lpm mode. And then when the load is set to
high, and more current is drawn, than is allowed in lpm, the dip is seen.
Link: https://lore.kernel.org/r/1581392451-28743-3-git-send-email-cang@codeaurora.org
Reviewed-by: Hongwu Su <hongwus@codeaurora.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Exception event can be raised by the device when system suspend is in
progress. This will result in unclocked register access in exception event
handler as clocks will be turned off during suspend. This change makes sure
to flush exception event handler work in suspend before disabling clocks to
avoid unclocked register access issue.
Link: https://lore.kernel.org/r/1581392451-28743-2-git-send-email-cang@codeaurora.org
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Sayali Lokhande <sayalil@codeaurora.org>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Auto-Hibern8 may be disabled by some vendors or sysfs in runtime even if
Auto-Hibern8 capability is supported by host. If Auto-Hibern8 capability is
supported by host but not actually enabled, Auto-Hibern8 error shall not
happen.
To fix this, provide a way to detect if Auto-Hibern8 is actually enabled
first, and bypass Auto-Hibern8 disabling case in
ufshcd_is_auto_hibern8_error().
Fixes: 8217444039 ("scsi: ufs: Add error-handling of Auto-Hibernate")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200129105251.12466-4-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to Jedec standard UFS 3.0 and UFS 2.1 Spec, Maximum number of
logical units supported by the UFS device is indicated by parameter
bMaxNumberLU in Geometry Descriptor. This patch is to delete current hard
code macro definition of UFS_UPIU_MAX_GENERAL_LUN, and switch to use device
indicated number instead.
Link: https://lore.kernel.org/r/20200120130820.1737-9-huobean@gmail.com
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add one new parameter max_lu_supported in struct ufs_dev_info, which will
be used to express exactly how many general LUs being supported by UFS
device, and initialize it during booting stage. This patch also adds a new
function ufshcd_device_geo_params_init() for initialization of UFS device
geometry descriptor related parameters.
Link: https://lore.kernel.org/r/20200120130820.1737-8-huobean@gmail.com
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Without variable is_init_prefetch, the current logic can guarantee
ufshcd_init_icc_levels() will execute only once, delete it now.
Link: https://lore.kernel.org/r/20200120130820.1737-7-huobean@gmail.com
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Delete ufshcd_read_power_desc() and ufshcd_read_device_desc(), directly
inline ufshcd_read_desc() into its callers.
Link: https://lore.kernel.org/r/20200120130820.1737-6-huobean@gmail.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ufshcd_get_max_pwr_mode() only need to be called once while booting, take
it out from ufshcd_probe_hba() and inline into ufshcd_device_params_init().
Link: https://lore.kernel.org/r/20200120130820.1737-5-huobean@gmail.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch has two major non-functionality changes:
1. Take scanning host if-statement out from ufshcd_probe_hba(), and move
into a new added function ufshcd_add_lus(). In this new function
ufshcd_add_lus(), the main functionalitis include: ICC initialization, add
well-known LUs, devfreq initialization, UFS bsg probe and scsi host
scan. The reason for this change is that these functionalities only being
called during booting stage flow ufshcd_init()->ufshcd_async_scan(). In the
processes of error handling and power management ufshcd_suspend(),
ufshcd_resume(), ufshcd_probe_hba() being called, but these functionalitis
above metioned are not hit.
2. Move context of initialization of parameters associated with the UFS
device to a new added function ufshcd_device_params_init(). The reason of
this change is that all of these parameters are used by driver, but only
need to be initialized once when booting. Combine them into an integral
function, make them easier maintain.
Link: https://lore.kernel.org/r/20200120130820.1737-4-huobean@gmail.com
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In consideration of UFS host driver uses parameters of struct ufs_dev_desc,
move its parameters to struct ufs_dev_info, delete struct ufs_dev_desc.
Link: https://lore.kernel.org/r/20200120130820.1737-3-huobean@gmail.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A non-zero error value likely being returned by ufshcd_scsi_add_wlus() in
case of failure of adding the WLs, but ufshcd_probe_hba() doesn't use this
value, and doesn't report this failure to upper caller. This patch is to
fix this issue.
Fixes: 2a8fa60044 ("ufs: manually add well known logical units")
Link: https://lore.kernel.org/r/20200120130820.1737-2-huobean@gmail.com
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Export below functions for vendor usage:
int ufshcd_hba_enable(struct ufs_hba *hba);
int ufshcd_make_hba_operational(struct ufs_hba *hba);
int ufshcd_uic_hibern8_exit(struct ufs_hba *hba);
Link: https://lore.kernel.org/r/20200117035108.19699-3-stanley.chu@mediatek.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pass UFS device information to vendor-specific variant callback
"apply_dev_quirks" because some platform vendors need to know such
information to apply special handling or quirks in specific devices.
At the same time, modify existing vendor implementations according to the
new interface for those vendor drivers which will be built-in or built as a
module alone with UFS core driver.
[mkp: clarified commit desc]
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Asutosh Das <asutoshd@codeaurora.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1578726707-6596-2-git-send-email-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove "errors" word in output string by ufshcd_print_err_hist() since not
all printed targets are "errors". Sometimes they are just "events".
In addition, all events which can be treated as "errors" already have "err"
or "fail" words in their names.
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Asutosh Das <asutoshd@codeaurora.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1578147968-30938-4-git-send-email-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Device reset history shall be also added for vendor's device reset variant
operation implementation.
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Asutosh Das <asutoshd@codeaurora.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1578147968-30938-3-git-send-email-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently checking if an error history element is empty or not is by its
"value". In most cases, value is error code.
However this checking is not correct because some errors or events do not
specify any values in error history so values remain as 0, and this will
lead to incorrect empty checking.
Fix it by checking "timestamp" instead of "value" because timestamp will be
always assigned for all history elements
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Asutosh Das <asutoshd@codeaurora.org>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1578147968-30938-2-git-send-email-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Can Guo