It is a flag anyway, so move it to existing u8 flag and don't waste mem.
Fix the flags to be in single u8 on the way.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add RGMII TX/RX delay configuration support. RGMII standard requires 2ns
delay to help the RGMII bridge receiver to sample data correctly. If the
default value does not provide proper centering of the data sample, the
TX/RX delay parameters can be used to adjust accordingly.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other callers of udp_tunnel6_xmit_skb just pass 0 for the prio
argument. Jesse Gross <jesse@nicira.com> suggested that prio is really
the same as IPv4's tos and should be handled the same, so this is my
interpretation of that suggestion.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Jesse Gross <jesse@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NOTE: Link-local IPv6 addresses for remote endpoints are not supported,
since the driver currently has no capacity for binding a geneve
interface to a specific link.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This supports a way to get target stats through normal
ethtool stats API.
For instance:
# ethtool -S wlan1
NIC statistics:
tx_pkts_nic: 353
tx_bytes_nic: 25142
rx_pkts_nic: 6
rx_bytes_nic: 996
d_tx_ucast_pkts: 89
d_tx_bcast_pkts: 264
d_tx_ucast_bytes: 3020
d_tx_bcast_bytes: 22122
...
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will allow us to call it from elsewhere when implementing
ethtool stats.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Improper use of strlcpy caused garbage to be appended to the
firmware version string. Fix this by paying attention to the
ie_lenth.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It can take a user a while to understand why their
NIC that advertises 802.11n support cannot actually
do 802.11n. Print out a warning in the logs to save
the next poor person to use this NIC some trouble.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This lets 'iw phy phy0 info' report antennas for
the radio device:
...
Available Antennas: TX 0x2 RX 0x2
Configured Antennas: TX 0x2 RX 0x2
...
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When configuring Tx vring for new connection,
WMI call to the firmware may fail. In this case, need to
clean up properly. In particular, need to call
cfg80211_del_sta() in case of AP like interface.
Perform full "disconnect" procedure for proper clean up
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Adjust driver behavior during FW boot. Proper sequence of
events after reset and FW download, is as following:
- FW prepares mailbox structure and reports IRQ "FW_READY"
- driver caches mailbox registers, marks mailbox readiness
- FW sends WMI_FW_READY event, ignore it
- FW sends WMI_READY event with some data
- driver stores relevant data marks FW is operational
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When Tx ring full is encountered with TSO,
printout of "DMA error" was wrongly printed.
In addition, in case of Tx ring full return
proper error code so that NETDEV_TX_BUSY is
returned to network stack in order not to
drop the packets and retry transmission of the
packets when ring is emptied.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some events are ignored for purpose; such events should not
be treated as "unhandled events". Replace info message
saying "unhandled" with debug one saying "ignore", to reduce
dmesg pollution
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the hardware name, revision and update the pci_id table.
Currently there're two HW ref. designs available I'm aware of,
with 1.0.2 and 1.1 chip revisions. I've access and been using
the first one so far and this patch cover only it.
QCA9377 inherits most of the stuff (e.g. fw interfaces)
from QCA61x4 design, so the integration was pretty straightforward.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To reflect configured antenna settings in HT/VHT MCS map,
reload the HT/VHT capabilities upon antenna change.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Move HT and VHT capabiltity setup static functions to avoid
forward declaration.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HT/VHT MCS rateset should be filled only for configured chainmask
rather that max supported chainmask. Fix that by checking configured
chainmask while filling HT/VHT MCS rate map.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Removing supported chainmask fields as it can be always derived
from num_rf_chains.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For the messages from host to target, shadow copy of CE descriptors
are maintained in source ring. Before writing actual CE descriptor,
first shadow copy is filled and then it is copied to CE address space.
To optimize in download path and to reduce d-cache pressure, removing
shadow copy of CE descriptors. This will also reduce driver memory
consumption by 33KB during on device probing.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The physical address necessary to unmap DMA ('bufferp') is stored
in ath10k_skb_cb as 'paddr'. ath10k doesn't rely on the meta/transfer_id
when handling send completion (htc ep id is stored in sk_buff control
buffer). So the unused output arguments {bufferp, nbytesp and transfer_idp}
are removed from CE send completion. This change is needed before removing
the shadow copy of copy engine (CE) descriptors in follow up patch.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
CE diag window access is serialized (it has to be by design) so
there's no way to get a different send completion. so there's no
need for post completion validation.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently to avoid uncached memory access while filling up copy engine
descriptors, shadow descriptors are used. This can be optimized further
by removing shadow descriptors. To achieve that first shadow ring
dependency in ce_send is removed by creating local copy of the
descriptor on stack and make a one-shot copy into the "uncached"
descriptor.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds support for getting firmware debug stats in 10.4 fw.
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI-TLV and FW API support in ath10k testmode.
Ath10k can get right wmi command format from UTF image
to communicate UTF firmware.
Signed-off-by: Alan Liu <alanliu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
European Union has made it mandatory that all devices working in 2.4 GHz
has to adhere to the ETSI specification (ETSI EN 300 328 V1.9.1)
beginnig this year. The standard basically speaks about interferences
in 2.4Ghz band.
For example, when 802.11 device detects interference, TX must be stopped
as long as interference is present.
Adaptive CCA is a feature, when enabled the device learns from the
environment and configures CCA levels adaptively. This will improve
detecting interferences and the device can stop trasmissions till the
interference is present eventually leading to good performances in
varying interference conditions.
The patch includes code for enabling adaptive CCA for 10.2.4 firmware on
QCA988X.
Signed-off-by: Maharaja <c_mkenna@qti.qualcomm.com>
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ssb bus can be found on various "host" devices like PCI/PCMCIA/SDIO.
Every ssb bus contains cores AKA devices.
The main idea is to have ssb driver scan/initialize bus and register
ready-to-use cores. This way ssb drivers can operate on a single core
mostly ignoring underlaying details.
For some reason PCMCIA support was split between ssb and b43. We got
PCMCIA host device probing in b43, then bus scanning in ssb and then
wireless core probing back in b43. The truth is it's very unlikely we
will ever see PCMCIA ssb device with no 802.11 core but I still don't
see any advantage of the current architecture.
With proposed change we get the same functionality with a simpler
architecture, less Kconfig symbols, one killed EXPORT and hopefully
cleaner b43. Since b43 supports both: ssb & bcma I prefer to keep ssb
specific code in ssb driver.
This mostly moves code from b43's pcmcia.c to bridge_pcmcia_80211.c. We
already use similar solution with b43_pci_bridge.c. I didn't use "b43"
in name of this new file as in theory any driver can operate on wireless
core.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In uap mode the carrier is not enabled until after the first STA joins.
The carrier triggers the bridge to start its state machine, and if STP
is enabled, it takes 4 seconds as it transitions from disabled to
forwarding. During this time the bridge drops all traffic, and the EAPOL
handshake times out after 3 seconds, preventing stations from joining.
Follow the logic used in mac80211 and start the carrier in start_ap
and disable it in stop_ap. This has a nice benefit of allowing the
first station connection time to be reduced by up to 75% when STP is
in use.
Signed-off-by: Martin Faltesek <mfaltesek@google.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wcn36xx implements a ring buffer for transmitted frames for each
(high and low priority) DMA channel. The ring buffers are lockless:
new frames are inserted at the head of the queue, while finished
packets are reaped from the tail.
Unfortunately, the list manipulations are missing any kind of barriers
so are susceptible to various races: for example, a TX completion
handler might read an updated desc->ctrl before the head has actually
advanced, and then null out the ctl->skb pointer while it is still
being used in the TX path.
Simplify things here by adding a spin lock when traversing the ring.
This change increased stability for me without adding any noticeable
overhead on my platform (xperia z).
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some of the ath9k_phyerr enums were wrong from the
beginning (and even before). Most of the time the
codes were used for counters to be displayed over
debugfs, which made this a non-functional issue.
Some (e.g. ATH9K_PHYERR_FALSE_RADAR_EXT) are used
for radar detection and require the correct code
to work as intended.
This patch includes:
a) fixes
ATH9K_PHYERR_FALSE_RADAR_EXT: 24 => 36
ATH9K_PHYERR_CCK_LENGTH_ILLEGAL: 32 => 28
ATH9K_PHYERR_CCK_POWER_DROP: 33 => 29
ATH9K_PHYERR_HT_CRC_ERROR: 34 => 32
ATH9K_PHYERR_HT_LENGTH_ILLEGAL: 35 => 33
ATH9K_PHYERR_HT_RATE_ILLEGAL: 36 => 34
b) extensions
ATH9K_PHYERR_CCK_BLOCKER = 24
ATH9K_PHYERR_HT_ZLF = 35
ATH9K_PHYERR_GREEN_FIELD = 37
Aside from the correction and completion made in
the enum, the patch also extends the display of
the related counters in the debugfs.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The current code exits after alloc_orinocodev, but fails to change the
return value to something that indicates the failure. This patch
changes the return value to -ENOMEM.
https://bugzilla.kernel.org/show_bug.cgi?id=106181
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SIOCSIWAP (airo_set_wap) affects scan: only the AP specified by
SIOCSIWAP is present in scan results.
This makes NetworkManager work for the first time but then unable to
find any other APs.
Clear APList before starting scan and set it back after scan completes
to work-around the problem.
To avoid losing packets during scan, modify disable_MAC() to omit
netif_carrier_off() call when lock == 2.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of dynamically allocating APList, make it a member of struct
airo_info to always track state of APList_rid.
This simplifies suspend/resume and allows removal of readAPListRid.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* fixes and cleanups in scan
* support of several scan plans
* improvements in FTM
* fixes in FW API
* improvements in the failure paths when the bus is dead
* other various small things here and there
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=a6Vu
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-10-25' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* bug fix for TDLS
* fixes and cleanups in scan
* support of several scan plans
* improvements in FTM
* fixes in FW API
* improvements in the failure paths when the bus is dead
* other various small things here and there
When doing memcpy/memset of EQEs, we should use sizeof struct
mlx4_eqe as the base size and not caps.eqe_size which could be bigger.
If caps.eqe_size is bigger than the struct mlx4_eqe then we corrupt
data in the master context.
When using a 64 byte stride, the memcpy copied over 63 bytes to the
slave_eq structure. This resulted in copying over the entire eqe of
interest, including its ownership bit -- and also 31 bytes of garbage
into the next WQE in the slave EQ -- which did NOT include the ownership
bit (and therefore had no impact).
However, once the stride is increased to 128, we are overwriting the
ownership bits of *three* eqes in the slave_eq struct. This results
in an incorrect ownership bit for those eqes, which causes the eq to
seem to be full. The issue therefore surfaced only once 128-byte EQEs
started being used in SRIOV and (overarchitectures that have 128/256
byte cache-lines such as PPC) - e.g after commit 77507aa249
"net/mlx4_core: Enable CQE/EQE stride support".
Fixes: 08ff32352d ('mlx4: 64-byte CQE/EQE support')
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not set the ins_vlan field to zero when no vlan id is present in the packet.
Since WQEs in the TX ring are not zeroed out between uses, this oversight
could result in having vlan flags present in the WQE ctrl segment when no
vlan is preset.
Fixes: e38af4faf0 ('net/mlx4_en: Add support for hardware accelerated 802.1ad vlan')
Reported-by: Gideon Naim <gideonn@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
delete action of ETHTOOL_ID_ON/ETHTOOL_ID_OFF in XGE ethtool -p,
so Hardware control the LED state instead of software.
Signed-off-by: Li Peng <lipeng321@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increased TX_TIMEOUT to 5HZ to accommodate worst case situation
for traffic and CPU intensive use cases
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Abhimanyu <abhimanyu@freescale.com>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* using netdev carrier state
* add and rework some cfg80211 callbacks mainly for AP mode
* use devcoredump when triggered by firmware event
realtek
* create new directory drivers/net/wireless/realtek/ for all realtek
drivers, not visible to users (no kconfig changes etc)
* add rtl8xxxu, a new mac80211 driver for RTL8723AU, RTL8188CU,
RTL8188RU, RTL8191CU, RTL8192CU and hopefully more in the future
ath10k
* add board 2 API support for automatically choosing correct board file
* data path optimisations
* disable PCI power save for qca988x and QCA99x0 due to interop reasons
wil6210
* BlockAckReq support
* firmware crashdump using devcoredump
* capture all frames with sniffer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWLzQ5AAoJEG4XJFUm622btRwH/A6fS7p5uSZzH5lIU8ZBLc7X
MzC1jYVepHXaR5+OhBIbQ5oSo47Y4xqMeO2ylFMpUSg4vntqR9yZNVH2lXV5EfPB
fIaGYIsb3ExjAFoIjFUBwqSOB7CCZK5myk+SLiOu9XghjsLObP5JLKgA49PGhFRn
CCuDq9diDNeJBnVzTS1ms5wO6RmOBiizzjbu7adJI0Hu63z2+P4pNMG4Zz6E1z97
z8DRFEwdNN9gKHIaEC61h7ZT9XDB/Tj31Wl3Irbi4GBS7sRXnFK46FYU8fMVDbDZ
ykj05sq6nTrfwfVZtXbV3SxlYNSN4SFFRuskon6IUcIzlNTuIULgvlpCjJJ6tyQ=
=pFoQ
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-10-27' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
here's a bigger pull request for 4.4. The diffstat looks scary as we
created a new directory realtek for all realtek drivers. In the future
I'm planning to create similar directories for all vendors, currently we
just have ath, mediatek and realtek. This change has been in linux-next
for a couple of weeks so it should be safe, but of course you never
know.
There's also a new driver rtl8xxxu for few realtek USB devices. This
just made it to the last linux-next build.
Otherwise there's nothing really special, more info below. If time
permits, and it's ok for you, I'm hoping to send you a one more pull
request this week.
brcmfmac
* using netdev carrier state
* add and rework some cfg80211 callbacks mainly for AP mode
* use devcoredump when triggered by firmware event
realtek
* create new directory drivers/net/wireless/realtek/ for all realtek
drivers, not visible to users (no kconfig changes etc)
* add rtl8xxxu, a new mac80211 driver for RTL8723AU, RTL8188CU,
RTL8188RU, RTL8191CU, RTL8192CU and hopefully more in the future
ath10k
* add board 2 API support for automatically choosing correct board file
* data path optimisations
* disable PCI power save for qca988x and QCA99x0 due to interop reasons
wil6210
* BlockAckReq support
* firmware crashdump using devcoredump
* capture all frames with sniffer
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
During Tx cleanup it's still possible for the descriptor data to be
read ahead of the descriptor index. A memory barrier is required between
the read of the descriptor index and the start of the Tx cleanup loop.
This allows a change to a lighter-weight barrier in the Tx transmit
routine just before updating the current descriptor index.
Since the memory barrier does result in extra overhead on arm64, keep
the previous change to not chase the current descriptor value. This
prevents the execution of the barrier for each loop performed.
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forcedeth currently uses disable_irq_lockdep and enable_irq_lockdep, which in
some configurations simply calls local_irq_disable. This causes errant warnings
in the netpoll path as in netpoll_send_skb_on_dev, where we disable irqs using
local_irq_save, leading to the following warning:
WARNING: at net/core/netpoll.c:352 netpoll_send_skb_on_dev+0x243/0x250() (Not
tainted)
Hardware name:
netpoll_send_skb_on_dev(): eth0 enabled interrupts in poll
(nv_start_xmit_optimized+0x0/0x860 [forcedeth])
Modules linked in: netconsole(+) configfs ipv6 iptable_filter ip_tables ppdev
parport_pc parport sg microcode serio_raw edac_core edac_mce_amd k8temp
snd_hda_codec_realtek snd_hda_codec_generic forcedeth snd_hda_intel
snd_hda_codec snd_hwdep snd_seq snd_seq_device snd_pcm snd_timer snd soundcore
snd_page_alloc i2c_nforce2 i2c_core shpchp ext4 jbd2 mbcache sr_mod cdrom sd_mod
crc_t10dif pata_amd ata_generic pata_acpi sata_nv dm_mirror dm_region_hash
dm_log dm_mod [last unloaded: scsi_wait_scan]
Pid: 1940, comm: modprobe Not tainted 2.6.32-573.7.1.el6.x86_64.debug #1
Call Trace:
[<ffffffff8107bbc1>] ? warn_slowpath_common+0x91/0xe0
[<ffffffff8107bcc6>] ? warn_slowpath_fmt+0x46/0x60
[<ffffffffa00fe5b0>] ? nv_start_xmit_optimized+0x0/0x860 [forcedeth]
[<ffffffff814b3593>] ? netpoll_send_skb_on_dev+0x243/0x250
[<ffffffff814b37c9>] ? netpoll_send_udp+0x229/0x270
[<ffffffffa02e3299>] ? write_msg+0x39/0x110 [netconsole]
[<ffffffffa02e331b>] ? write_msg+0xbb/0x110 [netconsole]
[<ffffffff8107bd55>] ? __call_console_drivers+0x75/0x90
[<ffffffff8107bdba>] ? _call_console_drivers+0x4a/0x80
[<ffffffff8107c445>] ? release_console_sem+0xe5/0x250
[<ffffffff8107d200>] ? register_console+0x190/0x3e0
[<ffffffffa02e71a6>] ? init_netconsole+0x1a6/0x216 [netconsole]
[<ffffffffa02e7000>] ? init_netconsole+0x0/0x216 [netconsole]
[<ffffffff810020d0>] ? do_one_initcall+0xc0/0x280
[<ffffffff810d4933>] ? sys_init_module+0xe3/0x260
[<ffffffff8100b0d2>] ? system_call_fastpath+0x16/0x1b
---[ end trace f349c7af88e6a6d5 ]---
console [netcon0] enabled
netconsole: network logging started
Fix it by modifying the forcedeth code to use
disable_irq_nosync_lockdep_irqsavedisable_irq_nosync_lockdep_irqsave instead,
which saves and restores irq state properly. This also saves us a little code
in the process
Tested by the reporter, with successful restuls
Patch applies to the head of the net tree
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Reported-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reduces the overhead of locking for busy poll.
Previously the state was protected by a lock, whereas now
it's manipulated solely with atomic operations.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds basic ethtool operations to the qed driver, allowing support in:
- Statistics gathering [ethtool -S]
- Setting of debug level [ethtool -s <interface> msglvl]
- Getting basic information [ethtool, ethtool -i]
In addition it adds the ability to change the MTU.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device statistics can be gathered on-demand. This adds the qed support for
reading the statistics [both function and port] from the device, and adds
to the public API a method for requesting the current statistics.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds basic link functionality to qede - driver still doesn't provide
users with an API to change any link property, but it does request qed to
initialize the link using default configuration, and registers a callback
that allows it to get link notifications.
This patch adds the ability of the driver to set the carrier as active and
to enable traffic as a result of async. link notifications.
Following this patch, driver should be capable of running traffic.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Physical link is handled by the management Firmware.
This patch lays the infrastructure for attention handling in the driver,
as link change notifications arrive via async. attentions,
as well the handling of such notifications.
This patch also extends the API with the protocol drivers by adding
registered callbacks which the protocol driver passes to qed in order
to be notified of async. events originating from the FW/HW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to configure basic classification in driver by
implementing ndo_set_mac_address() and ndo_set_rx_mode().
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch includes the basic Rx/Tx support for the driver [although
carrier will still never be turned on].
Following this patch the driver registers a network device, initializes
it and prepares it for traffic.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds to the qed the support to configure various L2 elements,
such as channels and basic filtering conditions.
It also enhances its public API to allow qede to later utilize this
functionality.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Qlogic Everest Driver for Ethernet is the Ethernet specific module for
QL4xxx ethernet products by Qlogic.
This patch adds a very minimal PCI driver, one that doesn't yet register
a network device, but one that does interact with qed and does a basic
initialization of the HW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a public API for a network driver to work on top of QED.
The interface itself is very minimal - it's mostly infrastructure, as the
only content it has after this patch is a query for HW-based information
required for the creation of a network interface [I.e., no actual
protocol-specific configurations are supported].
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Qlogic Everest Driver is the backend module for the QL4xxx ethernet
products by Qlogic.
This module serves two main purposes:
1. It's responsible to contain all the common code that will be shared
between the various drivers that would be used with said line of
products. Flows such as chip initialization and de-initialization
fall under this category.
2. It would abstract the protocol-specific HW & FW components, allowing
the protocol drivers to have a clean APIs which is detached in its
slowpath configuration from the actual HSI.
This adds a very basic module without any protocol-specific bits.
I.e., this adds a basic implementation that almost entirely falls under
the first category.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
xceiver handling (enable/disable) of the com20020 cards. The driver now handles
link status change detection. The EAE PCI-ARCNET cards now make use of the
rotary encoded subdevice indexing and got support for led triggers on transmit
and reconnection events.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NNwD
-----END PGP SIGNATURE-----
Merge tag 'arcnet-for-4.4-rc1' of git://git.pengutronix.de/git/mgr/linux
Michael Grzeschik says:
====================
This series includes code simplifaction. The main changes are the correct
xceiver handling (enable/disable) of the com20020 cards. The driver now handles
link status change detection. The EAE PCI-ARCNET cards now make use of the
rotary encoded subdevice indexing and got support for led triggers on transmit
and reconnection events.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
for_each_available_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
for_each_compatible_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression e;
local idexpression n;
@@
for_each_compatible_node(n,...) {
... when != of_node_put(n)
when != e = n
(
return n;
|
+ of_node_put(n);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
for_each_available_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
for_each_available_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression r.n;
expression r,e;
@@
for_each_available_child_of_node(r,n) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression r.n;
expression r,e;
@@
for_each_child_of_node(r,n) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression r.n;
expression r,e;
@@
for_each_child_of_node(r,n) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX buffer size calulation failed to account for the length granularity
(which is now 32 bytes)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both Renesas R-Car and RZ/A1 manuals state that RX buffer length must be
a multiple of 32 bytes, while the driver only uses 16 byte granularity...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the current driver mostly supports BCM7445 which has a hardcoded
location for its MoCA port on port 7 and port 0 for its internal PHY,
this is not necessarily true for all other chips out there such as
BCM3390 for instance.
Walk the list of ports from Device Tree, get their port number ("reg"
property), and then parse the "phy-mode" property and initialize two
internal variables: moca_port and a bitmask of internal PHYs. Since we
use interrupts for the MoCA port, we introduce two helper functions to
enable/disable interrupts and do this at the appropriate bank (INTRL2_0
or INTRL2_1).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the FDB add, delete, and dump operations. The add and
delete operations are implemented using directed ARL operations using
the specified MAC address and consist in a read operation, write and
readback operation.
The dump operation consists in using the ARL search and software
filtering entries which are not for the desired port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kbuild reported:
rtl8xxxu.c:5786:32: warning: ‘rtl8192cu_fops’ defined but not used [-Wunused-variable]
Fix it by adding temporary ifdefs around the static functions.
Fixes: 033695bdf6 ("rtl8xxxu: move devices supported by rtlwifi under UNTESTED config")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The arcnet device has no interrupt to detect if the link has changed
from disconnected to connected. This patch adds an timer to toggle the
link detection. The timer will get retriggered as long as the
reconnection interrupts accure. If the recon interrupts hold off
for >1s we define the connection stable again.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
The EAE PLX-PCI card has special leds on the the main io pci resource
bar. This patch adds support to trigger the conflict and data leds with
the packages.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
The EAE PLX-PCI card has a special rotary encoder
to configure the address of every card individually.
We take this information for the initial setup of
the cards dev_id.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
This patch sets the dev_port according to the index of
the card. This can be used by udev to name the ports
in userspace.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
This patch changes the driver to properly work with the linux netif
interface. The controller gets enabled on open and disabled on close.
Therefor it removes every bogus start of the xceiver. It only gets
enabled on com20020_open and disabled on com20020_close.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
The call for dev_free_skb is done only once. This patch
moves its call to its only user and removes the obsolete
condition variable.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
bnxt_gro_skb() has unused variables when CONFIG_INET is not set. We
really cannot support hardware GRO if CONFIG_INET is not set, so
compile out bnxt_gro_skb() completely and define BNXT_FLAG_GRO to be 0
if CONFIG_INET is not set. This will effectively always disable
hardware GRO if CONFIG_INET is not set.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx BSY error interrupt indicates that a frame was
received and discarded due to lack of buffers, so it's
a rx ring overflow condition and has nothing to do with
with bad rx packets. Use the right counter.
BSY conditions happen when the SoC is under performance
stress. Doing *more* work in stress situations by trying
to schedule NAPI is not a good idea as the stressed system
becomes still more stressed. The Rx interrupt is already
at work making sure the NAPI is scheduled.
So calling gfar_receive() here does not help. This issue
was present since day 1.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under one unusual circumstance it's possible to wrongly set
FILREN without enabling PRSDEP as well in the RCTRL register,
against the hardware specifications. With the default config
this does not happen because the default Rx offloads (Rx csum
and Rx VLAN) properly enable PRSDEP. But if anyone disables
all these offloads (via ethtool), we get a wrong configuration
were the Rx flow classification and hashing, and other Filer
based features (e.g. wake-on-filer interrupt) won't work.
This patch fixes the issue.
Also, account for Rx FCB insertion which happens every time
PRSDEP is set.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RQFCR_AND is duplicated.
Add missing space as well.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the mask used to update the LED configuration so that it clears
the necessary bits as well as setting the bits according to the mask.
Also reverse the LED configuration to show the Link state + collisions in
LEDA and the Link state + TX/RX events in LEDB.
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing function to clear the MIB statatistics was using the
wrong address for the registers. Also, the counters would of been
cleared when the interface was brought up, not during the
probe. Fix both of these.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the ethtool statistic interface, returning the full set
of statistics which both Armada 370, 38x and Armada XP can support.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ThunderX pass2 CPI and MPI configuration changes.
MPI_ALG is not enabled i.e MCAM parsing is disabled.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test for pass-1 silicon was incorrect, it should be for all
revisions less than 8. Also the revision is already present in the
pci_dev, so there is no need to read and keep a private copy.
Remove rev_id and code to read it from struct nicpf. Create new
static inline function pass1_silicon() to be used to testing the
silicon version. Use pass1_silicon() for revision checks, this will
be more widely used in follow on patches.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some silicon revisions, the soft reset clobbers PCI config space,
so quit doing the reset.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When reading external NVM file, if a section exists both in OTP
and in the external file, the memory that was allocated at OTP
reading is not freed.
This is possible only on systems that have an external NVM
file which is typically the case on embedded systems.
Signed-off-by: Moshe Harel <moshe.harel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The iwl_mvm_disable_queue function requires the TID to be set to
IWL_MAX_TID_COUNT when disabling an AC queue. Call it correctly for TDLS
scenarios.
Fixes: 4ecafae9e5 ("iwlwifi: mvm: support using multiple ACs on single HW queue")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In some cases, scan reference was taken, but wasn't
released even though scan command wasn't actually issued.
Change the current code to simply take the reference
only on success.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
As cfg80211 already enforces these limits, there's little point
in having them again here in our code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Implement config_iface_filter() driver op. Currently support only
probe request registration for p2p client vifs, by setting
MAC_FILTER_IN_PROBE_REQUEST flag in MAC_CONTEXT_CMD.
This is needed since WFDS spec and certification require a P2P client
to be discoverable on its operating channel.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Recovery takes too much time if the bus is dead (each timeout
is 2000ms, etc.).
Explicitly skip fw dump in this case, as it will result in
garbage data (and might take signifcant time)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add support for two scan plans for scheduled scan. The first plan
will run for a limited number of iterations, then the second plan
will run infinitely.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of only allowing the caller to decide whether the CMD_ASYNC
flag is set, let it pass the entire flags bitmask. This allows more
flexibility and will be needed when we call this function in the
suspend flow (where other flags are needed).
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This patch enables the debugfs user to configure an FTM responder
with the appropriate control channel position.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Those timeouts are used for AM-to-PSM transition.
We already have those pairs defined for default and WOWLAN use cases.
We expect that by using shorter threshold for low latency P2P,
e.g. for Miracast video scenario, we might save a considerable amount of power.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In "hostless" mode (D3 or D0i3) the same parameters were intended
to be used, but the code doesn't do that properly. Fix it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since the 8000 series, the DTS measurement request command has been
changed. Use an ucode capability flag to determine which version is
supported and send the extended command when needed.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The hardware bug in the commit mentioned below forces us
not to re-enable the clock gating in the Host Cluster.
The impact on the power consumption is minimal and it allows
the WAKE_ME interrupt to propagate.
CC: <stable@vger.kernel.org> [4.1+]
Fixes: c9fdec9f39 ("iwlwifi: pcie: fix prepare card flow")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When paging is enabled the driver stores part of the FW's
image in the DRAM.
Dump FW's virtual image in the case of a NIC error.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Remove an old workaround that's no longer needed and
enable MIMO on P2P interfaces.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are still four devices which are currently supported both by the new
rtl8xxxu driver and rtlwifi. To not break existing setups enable the support
for these four devices only when CONFIG_RTL8XXXU_UNTESTED is turned on.
Once rtl8xxxu support is found to be good enough the devices can be removed
from rtlwifi and enabled by default in rtl8xxxu.
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
struct bnxt_pf_info needs to be always defined. Move bnxt_update_vf_mac()
to bnxt_sriov.c and add some missing #ifdef CONFIG_BNXT_SRIOV.
Reported-by: Jim Hull <jim.hull@hpe.com>
Tested-by: Jim Hull <jim.hull@hpe.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-10-23
This series contains updates to i40e, i40evf, if_link, ixgbe and ixgbevf.
Anjali adds a workaround to drop any flow control frames from being
transmitted from any VSI, so that a malicious VF cannot send flow control
or PFC packets out on the wire. Also fixed a bug in debugfs by grabbing
the filter list lock before adding or deleting a filter.
Akeem fixes an issue where we were unconditionally returning VEB bridge
mode before allowing LB in the add VSI routine, resolve by checking if
the bridge is actually in VEB mode first.
Mitch fixed an issue where the incorrect structure was being used for
VLAN filter list, which meant the VLAN filter list did not get
processed correctly and VLAN filters would not be re-enabled after any
kind of reset.
Helin fixed a problem of possibly getting inconsistent flow control
status after a PF reset. The issue was requested_mode was being set
with a default value during probe, but the hardware state could be a
different value from this mode.
Carolyn fixed a problem where the driver output of the OEM version
string varied from the other tools.
Jean Sacren fixes up kernel documentation by fixing function header
comments to match actual variables used in the functions. Also
cleaned up variable initialization, when the variable would be
over-written immediately.
Hiroshi Shimanoto provides three patches to add "trusted" VF by adding
netlink directives and an NDO entry. Then implement these new controls
in ixgbe and ixgbevf. This series has gone through several iterations
to address all the suggested community changes and concerns.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The PV network protocol is using 4KB page granularity. The goal of this
patch is to allow a Linux using 64KB page granularity working as a
network backend on a non-modified Xen.
It's only necessary to adapt the ring size and break skb data in small
chunk of 4KB. The rest of the code is relying on the grant table code.
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
The PV network protocol is using 4KB page granularity. The goal of this
patch is to allow a Linux using 64KB page granularity using network
device on a non-modified Xen.
It's only necessary to adapt the ring size and break skb data in small
chunk of 4KB. The rest of the code is relying on the grant table code.
Note that we allocate a Linux page for each rx skb but only the first
4KB is used. We may improve the memory usage by extending the size of
the rx skb.
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
The skb doesn't change within the function. Therefore it's only
necessary to check if we need GSO once at the beginning.
Signed-off-by: Julien Grall <julien.grall@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Like mv88e6xxx and mdio-mux, to avoid lockdep give false positives
because of nested MDIO busses, switch to previously introduced
nested mdiobus_read/write variants.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the mv88e6xxx driver use the previously introduced nested
variants of mdiobus_read/write functions.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since nested variants of mdiobus_read/write are used in multiple
drivers, add nested variants in the mdiobus core.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The limitation of the number of multicast address for VF is not enough
for the large scale server with SR-IOV feature. IPv6 requires the multicast
MAC address for each IP address to handle the Neighbor Solicitation
message. We couldn't assign over 30 IPv6 addresses to a single VF.
This patch introduces the new mailbox API, IXGBE_VF_UPDATE_XCAST_MODE,
to update multicast mode of VF. This adds 3 modes;
- NONE only L2 exact match addresses or Flow Director enabled
- MULTI BAM and ROMPE set
- ALLMULTI BAM, ROMPE and MPE set
If a guest VF user wants over 30 MAC multicast addresses, set IFF_ALLMULTI
to request PF to update xcast mode to enable VF multicast promiscuous mode.
On the other hand, enabling VF multicast promiscuous mode may affect
security and performance in the network of the NIC. Only trusted VF can
enable multicast promiscuous mode. The behavior of untrusted VF is the
same as previous version.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implements the new netdev op to trust VF in ixgbe.
The administrator can turn on and off VF trusted by ip command which
supports trust message.
# ip link set dev eth0 vf 1 trust on
or
# ip link set dev eth0 vf 1 trust off
Send a ping to reset VF on changing the status of trusting.
VF driver will reconfigure its features on reset.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no reasons to probe cpsw from late_initcall level
and it's not recommended. Hence, use module_platform_driver()
to register and probe cpsw driver from module_init() level.
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 3092e5e4cc79 ("i40e: add little endian conversion for
checksum") fixed the checksum bug on big-endian architecture.
But we should not execute cpu_to_le16() unconditionally. Thus, put
cpu_to_le16() under certain condition.
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In both i40e_calc_nvm_checksum() and i40e_update_nvm_checksum(), the
local variables designated by 'ret_code' are overwritten immediately. As
such, they should merely be declared.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In i40evf_msix_aq(), the first two lines of rd32() are mainly to clear
the registers. If we initialize 'val' at this point, it will be
overwritten immediately. We shall simply discard the return value here.
When we initialize 'val', we might as well include the mask in one step.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The following kernel-doc arguments for their respective functions are
missing:
1) @cd_type_cmd_tso_mss for i40e_tso();
2) @cd_type_cmd_tso_mss for i40e_tsyn();
3) @tx_ring for i40e_tx_enable_csum().
Add them all for the kernel-doc requirement.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
@flush has been missing since the inception of i40evf_irq_enable(). Add
it for the kernel doc.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of using a custom approach change the code to use %*ph format
specifier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump up the version...
Change-ID: Ib8d501021671ba20250115ed54330e2c182255b7
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a call to enable SR-IOV in the kernel failed, we need to disable
I40E_FLAG_VEB_MODE_ENABLED, so that bridge mode could fall back to
VEPA, which is a default.
Change-ID: I12b6f776769506db85b29bea94b9c88d0b5ee65e
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where the driver output of the OEM
version string varied from the other tools. The mask value
and the order of operations were incorrect, per the original
change request. Without this patch, the version string will
appear incorrect from the driver.
Change-ID: Ie1ca6485284b4ce3b57e5a99b18b7641617c7ef7
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem of possibly getting inconsistent flow control
statuses after a PF reset. Requested_mode was being set with a default
value during probing, but the initial HW state could be different from
this mode.
Change-ID: I772bf07b78616e87086418d4bd87954b66fa17cd
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Not sure how this compiles at all. Use the correct struct for
manipulating the VLAN filter list. Without this, the VLAN filter
list doesn't get processed correctly, and VLAN filters will not
be re-enabled after any kind of reset.
Change-ID: Iceff2dc089f303058fb71ecb08419eed471e0e90
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix i40e_is_vsi_uplink_mode_veb to check if bridge is actually
in VEB mode before allowing LB in the add VSI routine, instead of
unconditionally returning VEB bridge mode.
Change-ID: I162397b1bdd02367735fe9baaeb51465be2a3ce9
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new code flow requires us to grab the filter list lock before
adding/deleting the filter.
Change-ID: I4eaef508ab4da2d1b2e23f20f2a78d931d5b6aeb
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a workaround to drop any flow control frames from being
transmitted from any VSI. FW can still send flow control frames if flow
control is enabled.
With this patch in place a malicious VF cannot send flow control or PFC
packets out on the wire.
Change-ID: I4303b24e98b93066d2767fec24dfe78be591c277
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We can't rely on PPPOX_ZOMBIE to decide whether to clear po->pppoe_dev.
PPPOX_ZOMBIE can be set by pppoe_disc_rcv() even when po->pppoe_dev is
NULL. So we have no guarantee that (sk->sk_state & PPPOX_ZOMBIE) implies
(po->pppoe_dev != NULL).
Since we're releasing a PPPoE socket, we want to release the pppoe_dev
if it exists and reset sk_state to PPPOX_DEAD, no matter the previous
value of sk_state. So we can just check for po->pppoe_dev and avoid any
assumption on sk->sk_state.
Fixes: 2b018d57ff ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code currently uses the lightweight dma_wmb barrier before updating
the current descriptor count. Under heavy load, the Tx cleanup routine
was seeing the updated current descriptor count before the updated
descriptor information. As a result, the Tx descriptor was being cleaned
up before it was used because it was not "owned" by the hardware yet,
resulting in a Tx queue hang.
Using the wmb barrier insures that the descriptor is updated before the
descriptor counter preventing the Tx queue hang. For extra insurance,
the Tx cleanup routine is changed to grab the current decriptor count on
entry and uses that initial value in the processing loop rather than
trying to chase the current value.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Very rarely, the KSZ9031 will appear to complete autonegotiation, but
will drop all traffic afterwards. When this happens, the idle error
count will read 0xFF after autonegotiation completes. Reset the PHY
when in that state.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't have fraglist support in TAP_FEATURES. This will lead
software segmentation of gro skb with frag list. Fixes by having
frag list support in TAP_FEATURES.
With this patch single session of netperf receiving were restored from
about 5Gb/s to about 12Gb/s on mlx4.
Fixes a567dd6252 ("macvtap: simplify usage of tap_features")
Cc: Vlad Yasevich <vyasevic@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While transitioning to netdev based vport we broke OVS
feature which allows user to retrieve tunnel packet egress
information for lwtunnel devices. Following patch fixes it
by introducing ndo operation to get the tunnel egress info.
Same ndo operation can be used for lwtunnel devices and compat
ovs-tnl-vport devices. So after adding such device operation
we can remove similar operation from ovs-vport.
Fixes: 614732eaa1 ("openvswitch: Use regular VXLAN net_device device").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom ethernet driver for the new family of NetXtreme-C/E
ethernet devices.
v5:
- Removed empty blank lines at end of files (noted by David Miller).
- Moved busy poll helper functions to bnxt.h to at least make the
.c file look less cluttered with #ifdef (noted by Stephen Hemminger).
v4:
- Broke up 2 long message strings with "\n" (suggested by John Linville)
- Constify an array of strings (suggested by Stephen Hemminger)
- Improve bnxt_vf_pciid() (suggested by Stephen Hemminger)
- Use PCI_VDEVICE() to populate pci_device_id table for more compact
source.
v3:
- Fixed 2 more sparse warnings.
- Removed some unused structures in .h files.
v2:
- Fixed all kbuild test robot reported warnings.
- Fixed many of the checkpatch.pl errors and warnings.
- Fixed the Kconfig description (noted by Dmitry Kravkov).
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Acked-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is preferable to have a common debugfs interface for DSA or switchdev
instead of a driver specific one. Thus remove the mv88e6xxx debug code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was printing a message about not being able
to assign VMDq because of a lack of MSI-X vectors.
This was because a line was missing that initialized a variable,
simply a merge error.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code was setting up stats that were not being initialized.
This caused several counters to be displayed incorrectly, due
to indexing beyond the array of strings when printing stats.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
New device IDs shamelessly lifted from the vendor driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that port_fdb_dump is implemented and even simpler, get rid of
port_fdb_getnext.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the port_fdb_dump DSA operation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to write the MAC address before every Get Next
operation, since ATU MAC registers are not cleared between calls.
Move the _mv88e6xxx_atu_mac_write call outside of _mv88e6xxx_atu_getnext
so future code could call ATU Get Next multiple times and save a few
register access.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to write the VLAN ID before every Get Next operation,
since the VTU VID register is not cleared between calls.
Move the VID write call in a _mv88e6xxx_vtu_vid_write function outside
of _mv88e6xxx_vtu_getnext so future code could call VTU Get Next
multiple times and save a few register accesses.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* I merged net-next back to avoid a conflict with the
* cfg80211 scheduled scan API extensions
* preparations for better scan result timestamping
* regulatory cleanups
* mac80211 statistics cleanups
* a few other small cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=uZ5N
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-10-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Here's another set of patches for the current cycle:
* I merged net-next back to avoid a conflict with the
* cfg80211 scheduled scan API extensions
* preparations for better scan result timestamping
* regulatory cleanups
* mac80211 statistics cleanups
* a few other small cleanups and fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
the global Soc configuration is treated by syscon, and sub ctrl bus is
Soc bus. it has to be treated by syscon.
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: lisheng <lisheng011@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update ethtool get_drvinfo to display regdump len and also update
firmware string version print to display N/A in case FW isn't present
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the ethtool set_settings() routine we need to remember our old L1
Configuration in case the firmware rejects the request and then restore
that.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For {1, 10, 40} Gb/s. Prohibiting turning off autonegotiation isn't anywhere
in the standard.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align the ethtool get stats settings with the rest so it looks uniform
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko