Add yet another rtnl_register function. It will be used by modules
that can be removed.
The passed module struct is used to prevent module unload while
a netlink dump is in progress or when a DOIT_UNLOCKED doit callback
is called.
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnetlink is littered with READ_ONCE() because we can have read accesses
while another cpu can write to the structure we're reading by
(un)registering doit or dumpit handlers.
This patch changes this so that (un)registering cpu allocates a new
structure and then publishes it via rcu_assign_pointer, i.e. once
another cpu can see such pointer no modifications will occur anymore.
based on initial patch from Peter Zijlstra.
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patch mistakenly removed three chip-specific config settings.
Add them again.
Fixes: 80274abafc "net: phy: remove generic settings for callbacks config_aneg and read_status from drivers"
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
William Tu says:
====================
add ip6 gre and gretap collect_md mode
Similar to gre, vxlan, geneve, ipip tunnels, allow ip6gretap tunnels to
operate in collect metadata mode. The first patch adds the support to
ip6_gre.c. The second patch enables unsetting the csum for ipv6 tunnel,
when using bpf_skb_[gs]et_tunnel_key() helpers. Finally, the last patch
adds the ip6 gre and gretap tunnel test cases to BPF sample code.
The corresponding iproute2 patch:
https://marc.info/?l=linux-netdev&m=151216943128087&w=2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend existing tests for vxlan, gre, geneve, ipip, erspan,
to include ip6 gre and gretap tunnel.
Signed-off-by: William Tu <u9012063@gmail.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before the patch, BPF_F_ZERO_CSUM_TX can be used only for ipv4 tunnel.
With introduction of ip6gretap collect_md mode, the flag should be also
supported for ipv6.
Signed-off-by: William Tu <u9012063@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to gre, vxlan, geneve, ipip tunnels, allow ip6 gre and gretap
tunnels to operate in collect metadata mode. bpf_skb_[gs]et_tunnel_key()
helpers can make use of it right away. OVS can use it as well in the
future.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If state is not PHY_HALTED I see no need to temporarily disable
interrupts on the device. As long as the current interrupt isn't acked
on the device no new interrupt can happen anyway.
In addition remove a unneeded enabling of interrupts in the state
machine when handling state PHY_CHANGELINK.
Tested on a Odroid-C2 with RTL8211F phy in interrupt mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commits c974bdbc3e "net: phy: Use threaded IRQ, to allow IRQ from
sleeping devices" and 664fcf123a "net: phy: Threaded interrupts allow
some simplification" all relevant code pieces run in process context
anyway and I don't think we need the disabling of interrupts any longer.
Interestingly enough, latter commit already removed the comment
explaining why interrupts need to be temporarily disabled.
On my system phy interrupt mode works fine with this patch.
However I may miss something, especially in the context of shared phy
interrupts, therefore I'd appreciate if more people could test this.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau says:
====================
tcp: Add a 2nd listener hashtable (port+addr)
This patch set adds a 2nd listener hashtable. It is to resolve
the performance issue when a process is listening at many IP
addresses with the same port (e.g. [IP1]:443, [IP2]:443... [IPN]:443)
v2:
- Move the new lhash2 and lhash2_mask before the existing
listening_hash to avoid adding another cacheline
to inet_hashinfo (Suggested by Eric Dumazet, Thanks!)
- I take this chance to plug an existing 4 bytes hole while
adding 'unsigned int lhash2_mask'.
- Add some comments about lhash2 in inet_hashtables.h
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the second listener hashtable in TCP.
The scale is the same as UDP which is one slot per 2MB.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current listener hashtable is hashed by port only.
When a process is listening at many IP addresses with the same port (e.g.
[IP1]:443, [IP2]:443... [IPN]:443), the inet[6]_lookup_listener()
performance is degraded to a link list. It is prone to syn attack.
UDP had a similar issue and a second hashtable was added to resolve it.
This patch adds a second hashtable for the listener's sockets.
The second hashtable is hashed by port and address.
It cannot reuse the existing skc_portaddr_node which is shared
with skc_bind_node. TCP listener needs to use skc_bind_node.
Instead, this patch adds a hlist_node 'icsk_listen_portaddr_node' to
the inet_connection_sock which the listener (like TCP) also belongs to.
The new portaddr hashtable may need two lookup (First by IP:PORT.
Second by INADDR_ANY:PORT if the IP:PORT is a not found). Hence,
it implements a similar cut off as UDP such that it will only consult the
new portaddr hashtable if the current port-only hashtable has >10
sk in the link-list.
lhash2 and lhash2_mask are added to 'struct inet_hashinfo'. I take
this chance to plug a 4 bytes hole. It is done by first moving
the existing bind_bucket_cachep up and then add the new
(int lhash2_mask, *lhash2) after the existing bhash_size.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the udp[46]_portaddr_hash()
to net/ip[v6].h. The function name is renamed to
ipv[46]_portaddr_hash().
It will be used by a later patch which adds a second listener
hashtable hashed by the address and port.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a count to the 'struct inet_listen_hashbucket'.
It counts how many sk is hashed to a bucket. It will be
used to decide if the (to-be-added) portaddr listener's hashtable
should be used during inet[6]_lookup_listener().
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool ops to advertise sw timestamping.
Call skb_tx_timestamp() just before ringing the wq doorbell.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger says:
====================
hv_netvsc: minor optimizations
These are a set of local optimizations the Hyper-V networking driver.
Also include a vmbus patch in this set, because it depends on the
netvsc that last used that function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The last use of hv_get_ringbuffer_availbytes in drivers is now
gone. Only used by the debug info routine so make it static. Also, add
READ_ONCE() to avoid any possible issues with potentially volatile
index values.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memset of the whole maximum possible RNDIS header is unnecessary.
For the main part of the header use a structure assignment.
No need to memset the whole per packet info. Instead rely on caller to
set what it wants. Also get rid of cast to void and signed/unsigned
conversion. Now return pointer to per packet data (rather than the
header) which simplifies use by code setting up the packet data.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every packet sent checks the available ring space. The calculation
can be sped up by using reciprocal divide which is multiplication.
Since ring_size can only be configured by module parameter, so it doesn't
have to be passed around everywhere. Also it should be unsigned
since it is number of pages.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet alignment is always a power of 2 therefore modulus can
be replaced with a faster and operation
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since skb is always non-NULL in the copy portion of netvsc_send
do not need local variable.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are multiple duplicated condition checks in the current codes, so
I add the new func ipvlan_is_valid_dev instead of the duplicated codes to
check if the netdev is real ipvlan dev.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Blumenstingl says:
====================
Realtek Ethernet PHY driver improvements
This series provides some small improvements and cleanups for the
Realtek Ethernet PHY driver.
None of the patches in this series should change any functionality.
The goal is to make the code a bit easier to read by:
- re-using the BIT and GENMASK macros (which makes it easier to compare
the #defines in the kernel with the values from the datasheets)
- rename a #define from a generic name to a PHY-specific name since it's
only used for one specific PHY
- logically group the register #defines and their register bit #defines
together
- indentation cleanups
- removed some code duplicating for reading/writing registers on a
Realtek specific "page"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtek PHYs implement the concept of so-called "extension pages". The
reason for this is probably because these PHYs expose more registers
than available in the standard address range.
After all read/write operations on such a page are done the driver
should switch back to page 0 where the standard MII registers (such as
MII_BMCR) are available.
When referring to such a register the datasheets of RTL8211E and
RTL8211F always specify:
- the page / "ext. page" which has to be written to RTL821x_PAGE_SELECT
- an address (sometimes also called reg)
These new utility functions make the existing code easier to read since
it removes some duplication (switching back to page 0 is done within the
new helpers for example).
No functional changes are intended.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simply makes the code easier to read. No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simply moves all register bit #defines which describe the (PHY
specific) bits in the RTL821x_INER right below the RTL821x_INER register
definition. This makes it easier to spot which registers and bits belong
together.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This macro is only used by the RTL8211B code. RTL8211E and RTL8211F both
use other bits to initialize the RTL821x_INER register.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes it easier to compare the #defines with the datasheets.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot says:
====================
net: dsa: cross-chip FDB support
DSA can have interconnected switches. For instance, the ZII Dev Rev B
board described in arch/arm/boot/dts/vf610-zii-dev-rev-b.dts has a
switch fabric composed of 3 switch devices like this:
lan4 lan6
CPU (eth1) | lan5 | lan7
| | | | |
[0 1 2 3 4 6 5]---[6 0 1 2 3 4 5]---[9 0 1 2 3 4 5 6 7 8]
| | | | | | |
lan0 | lan2 lan3 lan8 | optical4
lan1 optical3
One current issue with DSA is cross-chip FDB. If we add a static MAC
address on lan3, only its parent switch 1 (the one in the middle) will
be programmed. That is not correct in a cross-chip environment, because
the DSA ports connecting to switch 1 of adjacent switch 0 (on the left)
and switch 2 (on the right) must be programmed too.
Without this patchset, a dump of the hardware FDB of switches 0, 1 and 2
after programming a MAC address on lan3 looks like this (*):
# bridge fdb add 11:22:33:44:55:66 dev lan3
# cat /sys/kernel/debug/mv88e6xxx/sw*/atu/0 | grep -v FID
0 ff:ff:ff:ff:ff:ff MC_STATIC n 0 1 2 3 4 5 6
0 11:22:33:44:55:66 MC_STATIC_MGMT_PO n 0 - - - - - -
0 ff:ff:ff:ff:ff:ff MC_STATIC n 0 1 2 3 4 5 6
0 ff:ff:ff:ff:ff:ff MC_STATIC n 0 1 2 3 4 5 6 7 8 9
With this patchset applied, adjacent DSA ports get programmed too:
# bridge fdb add 11:22:33:44:55:66 dev lan3
# cat /sys/kernel/debug/mv88e6xxx/sw*/atu/0 | grep -v FID
0 11:22:33:44:55:66 MC_STATIC_MGMT_PO n - - - - - 5 -
0 ff:ff:ff:ff:ff:ff MC_STATIC n 0 1 2 3 4 5 6
0 11:22:33:44:55:66 MC_STATIC_MGMT_PO n 0 - - - - - -
0 ff:ff:ff:ff:ff:ff MC_STATIC n 0 1 2 3 4 5 6
0 11:22:33:44:55:66 MC_STATIC_MGMT_PO n - - - - - - - - - 9
0 ff:ff:ff:ff:ff:ff MC_STATIC n 0 1 2 3 4 5 6 7 8 9
In order to do that, the first commit introduces a dsa_towards_port()
helper which returns the local port of a switch which must be used to
reach an arbitrary switch port (local or from an adjacent switch.)
The second patch uses this helper to configure the port reaching the
target port for every switches of the fabric.
(*) a patch for squashed debugfs interface which applies on top of this
patchset is available here:
f8e6ba34c6.patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a MAC address is added to or removed from a switch port in the
fabric, the target switch must program its port and adjacent switches
must program their local DSA port used to reach the target switch.
For this purpose, use the dsa_towards_port() helper to identify the
local switch port which must be programmed.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new helper returning the local port used to reach an arbitrary
switch port in the fabric.
Its only user at the moment is the dsa_upstream_port helper, which
returns the local port reaching the dedicated CPU port, but it will be
used in cross-chip FDB operations.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot says:
====================
net: dsa: simplify switchdev prepare phase
This patch series brings no functional changes.
It removes the unused switchdev_trans arguments from the dsa_switch_ops
for both MDB and VLAN operations, and provides functions to prepare and
add these objects for a given bitmap of ports.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch brings no functional changes.
It moves out the MDB code iterating on a multicast group into new
dsa_switch_mdb_{prepare,add}_bitmap() functions.
This gives us a better isolation of the two switchdev phases.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch brings no functional changes.
It moves out the VLAN code iterating on a list of VLAN members into new
dsa_switch_vlan_{prepare,add}_bitmap() functions.
This gives us a better isolation of the two switchdev phases.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA switch MDB ops pass the switchdev_trans structure down to the
drivers, but no one is using them and they aren't supposed to anyway.
Remove the trans argument from MDB prepare and add operations.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA switch VLAN ops pass the switchdev_trans structure down to the
drivers, but no one is using them and they aren't supposed to anyway.
Remove the trans argument from VLAN prepare and add operations.
At the same time, fix the following checkpatch warning:
WARNING: line over 80 characters
#74: FILE: drivers/net/dsa/dsa_loop.c:177:
+ const struct switchdev_obj_port_vlan *vlan)
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 3a927bc7cf ("ovs: propagate per dp max headroom to
all vports") the need_headroom for the internal vport is updated
accordingly to the max needed headroom in its datapath.
That avoids the pskb_expand_head() costs when sending/forwarding
packets towards tunnel devices, at least for some scenarios.
We still require such copy when using the ovs-preferred configuration
for vxlan tunnels:
br_int
/ \
tap vxlan
(remote_ip:X)
br_phy
\
NIC
where the route towards the IP 'X' is via 'br_phy'.
When forwarding traffic from the tap towards the vxlan device, we
will call pskb_expand_head() in vxlan_build_skb() because
br-phy->needed_headroom is equal to tun->needed_headroom.
With this change we avoid updating the internal vport needed_headroom,
so that in the above scenario no head copy is needed, giving 5%
performance improvement in UDP throughput test.
As a trade-off, packets sent from the internal port towards a tunnel
device will now experience the head copy overhead. The rationale is
that the latter use-case is less relevant performance-wise.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko says:
====================
net: ethernet: ti: cpsw/ale clean up and optimization
This is set of non critical clean ups and optimizations for TI
CPSW and ALE drivers.
Rebased on top on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ALE ports number includes the Host port and ext Ports, and
ALE ports numbering starts from 0, so correct corresponding port
checks in cpsw_ale_control_set/get().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cpsw_ale_create in cpsw_ale_create(). This also makes
cpsw_ale_destroy() function nop, so remove it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move static initialization from cpsw_ale_start() to cpsw_ale_create() as it
does not make much sence to perform static initializtion in
cpsw_ale_start() which is called everytime netif[s] is opened.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ale->params.ale_ports parameter can be used to deriver values for all
ale entry mask bits: port_mask_bits, port_mask_bits, port_num_bits.
Hence, calculate above values and drop all hardcoded values. For
port_num_bits calcualtion use order_base_2() API.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ALE is enabled from cpsw_ale_start() now, but disabled only from
cpsw_ale_destroy() which introduces inconsitance as cpsw_ale_start() is
called when netif[s] is opened, but cpsw_ale_destroy() is called when
driver is removed. Hence, move ALE disabling in cpsw_ale_stop().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to use writel_relaxed/readl_relaxed() IO API instead of raw version
as it is recommended.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TI OMAP/Sitara SoCs have fixed number of ALE ports 3, which includes Host
port also.
Hence, use fixed value instead of value calcualted from DT, which can be
set by user and might not reflect actual HW configuration.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move mac_hi/lo defines in common header cpsw.h and re-use
them for netcp_ethss.c.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW platform data struct cpsw_platform_data and struct cpsw_slave_data are
used only incide cpsw.c module, so move these definitions there.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to use writel_relaxed/readl_relaxed() IO API instead of raw version
as it is recommended.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop unused variable "poll" from cpsw_update_channels_res().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal