Since the VD1 Amlogic FBC decoder is now configured by the overlay driver,
commit the right registers to decode the Amlogic FBC frame.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200703080728.25207-7-narmstrong@baylibre.com
Finally, setup the VIU registers and start the AFBC decoder to support
displaying AFBC encoded buffers on Amlogic GXM and G12A SoCs.
The RDMA is used here to reset and program the AFBC decoder unit
on each vsync without involving the interrupt handler that can
be masked for a long period of time, producing display glitches.
The vsync irq must still be left enabled otherwise the RDMA modules isn't
trigerred when the interrupt line is masked.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191021091509.3864-10-narmstrong@baylibre.com
This adds all the OSD configuration plumbing to support the AFBC decoders
path to display of the OSD1 plane.
The Amlogic GXM and G12A AFBC decoders are integrated very differently.
The Amlogic GXM has a direct output path to the OSD1 VIU pixel input,
because the GXM AFBC decoder seem to be a custom IP developed by Amlogic.
On the other side, the Amlogic G12A AFBC decoder seems to be an external
IP that emit pixels on an AXI master hooked to a "Mali Unpack" block
feeding the OSD1 VIU pixel input.
This uses a weird "0x1000000" internal HW physical address on both
sides to transfer the pixels.
For Amlogic GXM, the supported pixel formats are the same as the normal
linear OSD1 mode.
On the other side, Amlogic added support for all AFBC v1.2 formats for
the G12A AFBC integration.
For simplicity, we stick to the already supported formats for now.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191021091509.3864-7-narmstrong@baylibre.com
This patch introduce new enum which contains all VPU family (GXBB,
GXL, GXM and G12A).
This enum is used to detect the VPU compatible with the device.
We only need to set .data to the corresponding enum in the device
table, no need to check .compatible string anymore.
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87imqpz21w.fsf@masson.i-did-not-set--mail-host-address--so-tickle-me
This patch add new macros which describe couple bits field of the
following registers:
- VD1_BLEND_SRC_CTRL
- VPP_SC_MISC
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/86wohb82fa.fsf@baylibre.com
Drop use of the deprecated drmP.h header.
While doing so used the opportunity
to clean up a little so includes are now
sorted and removed unused include files.
In a few cases added some forwards to allow header
files to built in different include order.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Maxime Jourdan <mjourdan@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190716064220.18157-2-sam@ravnborg.org
The G12A Primary plane was disabled by writing in the OSD1 configuration
registers, but this caused the plane blender to stall instead of continuing
to blend only the overlay plane.
Fix this by disabling the OSD1 plane in the blender registers, and also
enabling it back using the same register.
Fixes: 490f50c109 ("drm/meson: Add G12A support for OSD1 Plane")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
[narmstrong: fixed nit in commit log]
Link: https://patchwork.freedesktop.org/patch/msgid/20190605141253.24165-3-narmstrong@baylibre.com
The primary plane disable logic is flawed, when the primary plane is
disabled, it is re-enabled in the vsync irq when another plane is updated.
Handle the plane disabling correctly by handling the primary plane
enable flag in the primary plane update & disable callbacks.
Fixes: 490f50c109 ("drm/meson: Add G12A support for OSD1 Plane")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190605141253.24165-2-narmstrong@baylibre.com
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the new OSD+VD Plane blending module
in the CRTC code by adding the G12A code to manage the blending
module and setting the right OSD1 & VD1 plane registers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-8-narmstrong@baylibre.com
Now that the DMC register range is no longer in the bindings, remove any
mention towards it and exclusively use the meson-canvas module.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190311105144.7276-3-mjourdan@baylibre.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlxqHJYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGWl8H/jPI4EipzD2GbnjZ
GaFpMBBjcXBaVmoA+Y69so+7BHx1Ql+5GQtqbK0RHJRb9qEPLw3FBhHNjM/N8Sgf
nSrK+GnBZp9s+k/NR/Yf2RacUR3jhz+Q9JEoQd3u9bFUeQyvE8Rf3vgtoBBwFOfz
+t7N1memYVF3asLGWB4e4sP1YVMGfseTQpSPojvM30YWM86Bv+QtSx1AGgHczQIM
kMKealR8ZPelN6JAXgLhQ5opDojBrE4YKB98pwsMDI6abz0Tz2JLFEUTTxsv5XNN
o/Iz+XDoylskEyxN2unNWfHx7Swkvoklog8J/hDg5XlTvipL/WkT66PHBgcGMNvj
BW9GgU8=
=ZizU
-----END PGP SIGNATURE-----
Merge v5.0-rc7 into drm-next
Backmerging for nouveau and imx that needed some fixes for next pulls.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Having the probe helper stuff (which pretty much everyone needs) in
the drm_crtc_helper.h file (which atomic drivers should never need) is
confusing. Split them out.
To make sure I actually achieved the goal here I went through all
drivers. And indeed, all atomic drivers are now free of
drm_crtc_helper.h includes.
v2: Make it compile. There was so much compile fail on arm drivers
that I figured I'll better not include any of the acks on v1.
v3: Massive rebase because i915 has lost a lot of drmP.h includes, but
not all: Through drm_crtc_helper.h > drm_modeset_helper.h -> drmP.h
there was still one, which this patch largely removes. Which means
rolling out lots more includes all over.
This will also conflict with ongoing drmP.h cleanup by others I
expect.
v3: Rebase on top of atomic bochs.
v4: Review from Laurent for bridge/rcar/omap/shmob/core bits:
- (re)move some of the added includes, use the better include files in
other places (all suggested from Laurent adopted unchanged).
- sort alphabetically
v5: Actually try to sort them, and while at it, sort all the ones I
touch.
v6: Rebase onto i915 changes.
v7: Rebase once more.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Acked-by: CK Hu <ck.hu@mediatek.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: virtualization@lists.linux-foundation.org
Cc: etnaviv@lists.freedesktop.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: spice-devel@lists.freedesktop.org
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-tegra@vger.kernel.org
Cc: xen-devel@lists.xen.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190117210334.13234-1-daniel.vetter@ffwll.ch
Since commit 2bcd3ecab7 when switching mode from X11 (ubuntu mate for
example) the display gets blurry, looking like an invalid framebuffer width.
This commit fixed atomic crtc modesetting in a totally wrong way and
introduced a local unnecessary ->enabled crtc state.
This commit reverts the crctc _begin() and _enable() changes and simply
adds drm_atomic_helper_commit_tail_rpm as helper.
Reported-by: Tony McKahan <tonymckahan@gmail.com>
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Fixes: 2bcd3ecab7 ("drm/meson: Fixes for drm_crtc_vblank_on/off support")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[narmstrong: fixed blank line issue from checkpatch]
Link: https://patchwork.freedesktop.org/patch/msgid/20190114153118.8024-1-narmstrong@baylibre.com
Since Linux 4.17, calls to drm_crtc_vblank_on/off are mandatory, and we get
a warning when ctrc is disabled :
" driver forgot to call drm_crtc_vblank_off()"
But, the vsync IRQ was not totally disabled due the transient hardware
state and specific interrupt line, thus adding proper IRQ masking from
the HHI system control registers.
The last change fixes a race condition introduced by calling the added
drm_crtc_vblank_on/off when an HPD event occurs from the HDMI connector,
triggering a WARN_ON() in the _atomic_begin() callback when the CRTC
is disabled, thus also triggering a WARN_ON() in drm_vblank_put() :
WARNING: CPU: 0 PID: 1185 at drivers/gpu/drm/meson/meson_crtc.c:157 meson_crtc_atomic_begin+0x78/0x80
[...]
Call trace:
meson_crtc_atomic_begin+0x78/0x80
drm_atomic_helper_commit_planes+0x140/0x218
drm_atomic_helper_commit_tail+0x38/0x80
commit_tail+0x7c/0x80
drm_atomic_helper_commit+0xdc/0x150
drm_atomic_commit+0x54/0x60
restore_fbdev_mode_atomic+0x198/0x238
restore_fbdev_mode+0x6c/0x1c0
drm_fb_helper_restore_fbdev_mode_unlocked+0x7c/0xf0
drm_fb_helper_set_par+0x34/0x60
drm_fb_helper_hotplug_event.part.28+0xb8/0xc8
drm_fbdev_client_hotplug+0xa4/0xe0
drm_client_dev_hotplug+0x90/0xe0
drm_kms_helper_hotplug_event+0x3c/0x48
drm_helper_hpd_irq_event+0x134/0x168
dw_hdmi_top_thread_irq+0x3c/0x50
[...]
WARNING: CPU: 0 PID: 1185 at drivers/gpu/drm/drm_vblank.c:1026 drm_vblank_put+0xb4/0xc8
[...]
Call trace:
drm_vblank_put+0xb4/0xc8
drm_crtc_vblank_put+0x24/0x30
drm_atomic_helper_wait_for_vblanks.part.9+0x130/0x2b8
drm_atomic_helper_commit_tail+0x68/0x80
[...]
The issue is that vblank need to be enabled in any occurrence of :
- atomic_enable()
- atomic_begin() and state->enable == true, which was not the case
Moving the CRTC enable code to a common function and calling in one of
these occurrence solves this race condition and makes sure vblank is
enabled in each call to _atomic_begin() from the HPD event leading to
drm_atomic_helper_commit_planes().
To Summarize :
- Make sure that the CRTC code will call the drm_crtc_vblank_on()/off()
- *Really* mask the Vsync IRQ
- Initialize and enable vblank at the first
atomic_begin()/_atomic_enable()
Cc: stable@vger.kernel.org # 4.17+
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
[fixed typos+added cc for stable]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181122160103.10993-1-narmstrong@baylibre.com
Signed-off-by: Sean Paul <seanpaul@chromium.org>
In preparation to support the Primary Plane scaling, move the basic
OSD Interlace-Only scaler setup code into the primary plane atomic
update callback and handle the vsync scaler update like the overlay
plane scaling registers update.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1541497202-20570-3-git-send-email-narmstrong@baylibre.com
The Amlogic Meson GX SoCs support an Overlay plane behind the primary
plane for video rendering.
This Overlay plane support various YUV layouts :
- YUYV
- NV12 / NV21
- YUV444 / 422 / 420 / 411 / 410
The scaler supports a wide range of scaling ratios, but for simplicity,
plane atomic check limits the scaling from x5 to /5 in vertical and
horizontal scaling.
The z-order is fixed and always behind the primary plane and cannot be changed.
The scaling parameter algorithm was taken from the Amlogic vendor kernel
code and rewritten to match the atomic universal plane requirements.
The video rendering using this overlay plane support has been tested using
the new Kodi DRM-KMS Prime rendering path along the in-review V4L2 Mem2Mem
Hardware Video Decoder up to 3840x2160 NV12 frames on various display modes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Maxime Jourdan <mjourdan@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1541497202-20570-2-git-send-email-narmstrong@baylibre.com
This is the first step into converting the meson/drm driver to use
the canvas module.
If a canvas provider node is detected in DT, use it. Otherwise,
fall back to what is currently being done.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: added back priv in meson_drv_unbind()]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181105104508.23090-3-mjourdan@baylibre.com
The plane buffer address/stride/height was incorrectly updated in the
plane_atomic_update operation instead of the vsync irq.
This patch delays this operation in the vsync irq along with the
other plane delayed setup.
This issue was masked using legacy framebuffer and X11 modesetting, but
is clearly visible using gbm rendering when buffer is submitted late after
vblank, like using software decoding and OpenGL rendering in Kodi.
With this patch, tearing and other artifacts disappears completely.
Cc: Michal Lazo <michal.lazo@gmail.com>
Fixes: bbbe775ec5 ("drm: Add support for Amlogic Meson Graphic Controller")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1518689976-23292-1-git-send-email-narmstrong@baylibre.com
The CRTC .disable() helper operation is deprecated for atomic drivers,
the new .atomic_disable() helper operation being preferred. Convert all
atomic drivers to .atomic_disable() to avoid cargo-cult use of
.disable() in new drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # for sun4i
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> # for mediatek
Acked-by: Alexey Brodkin <abrodkin@synopsys.com> # for arcpgu
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # for atmel-hlcdc
Tested-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Vincent Abriou <vincent.abriou@st.com> # for sti
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> # for vmwgfx
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170630093646.7928-3-laurent.pinchart+renesas@ideasonboard.com
The old state is useful for drivers that need to perform operations at
enable time that depend on the transition between the old and new
states.
While at it, rename the operation to .atomic_enable() to be consistent
with .atomic_disable(), as the .enable() operation is used by atomic
helpers only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # for sun4i
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> # for imx-drm and mediatek
Acked-by: Alexey Brodkin <abrodkin@synopsys.com> # for arcpgu
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # for atmel-hlcdc
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com> # for hdlcd and mali-dp
Acked-by: Stefan Agner <stefan@agner.ch> # for fsl-dcu
Tested-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Vincent Abriou <vincent.abriou@st.com> # for sti
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> # for vmwgfx
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170630093646.7928-2-laurent.pinchart+renesas@ideasonboard.com
Clean the crtc_enable by using the proper crtc_state instead of the state
of the primary plane state data.
Also fix the dependency to commit the plane changes even if enable is called
after the flush.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The vblank hooks in struct drm_driver are deprecated and only meant for
legacy drivers. For modern drivers with DRIVER_MODESET flag, the hooks
in struct drm_crtc_funcs should be used instead.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1486458995-31018-15-git-send-email-shawnguo@kernel.org
The Amlogic Meson Display controller is composed of several components :
DMC|---------------VPU (Video Processing Unit)----------------|------HHI------|
| vd1 _______ _____________ _________________ | |
D |-------| |----| | | | | HDMI PLL |
D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK |
R |-------| |----| Processing | | | | |
| osd2 | | | |---| Enci ----------|----|-----VDAC------|
R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----|
A | osd1 | | | Blenders | | Encl ----------|----|---------------|
M |-------|______|----|____________| |________________| | |
___|__________________________________________________________|_______________|
VIU: Video Input Unit
---------------------
The Video Input Unit is in charge of the pixel scanout from the DDR memory.
It fetches the frames addresses, stride and parameters from the "Canvas" memory.
This part is also in charge of the CSC (Colorspace Conversion).
It can handle 2 OSD Planes and 2 Video Planes.
VPP: Video Post Processing
--------------------------
The Video Post Processing is in charge of the scaling and blending of the
various planes into a single pixel stream.
There is a special "pre-blending" used by the video planes with a dedicated
scaler and a "post-blending" to merge with the OSD Planes.
The OSD planes also have a dedicated scaler for one of the OSD.
VENC: Video Encoders
--------------------
The VENC is composed of the multiple pixel encoders :
- ENCI : Interlace Video encoder for CVBS and Interlace HDMI
- ENCP : Progressive Video Encoder for HDMI
- ENCL : LCD LVDS Encoder
The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock
tree and provides the scanout clock to the VPP and VIU.
The ENCI is connected to a single VDAC for Composite Output.
The ENCI and ENCP are connected to an on-chip HDMI Transceiver.
This driver is a DRM/KMS driver using the following DRM components :
- GEM-CMA
- PRIME-CMA
- Atomic Modesetting
- FBDev-CMA
For the following SoCs :
- GXBB Family (S905)
- GXL Family (S905X, S905D)
- GXM Family (S912)
The current driver only supports the CVBS PAL/NTSC output modes, but the
CRTC/Planes management should support bigger modes.
But Advanced Colorspace Conversion, Scaling and HDMI Modes will be added in
a second time.
The Device Tree bindings makes use of the endpoints video interface definitions
to connect to the optional CVBS and in the future the HDMI Connector nodes.
HDMI Support is planned for a next release.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Maxime Ripard