This alters the Nomadik pinctrl driver to:
- Call irqdomain_add_linear() for the DT case so we get
all independent from IRQ numbers in this case.
- Call irqdomain_add_simple() for the legacy case, which
allocates the IRQ descriptors for the Nomadik pin controller
dynamically.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Upgrade nomadik pinctrl driver to enable selection of other
alternate-C[1-4] functions on some specific ux500 SoC pins.
Handling of those functions is done thanks to PRCM GPIOCR
registers. This was previously managed in PRCMU driver and
it was not really convenient. Idea is to provide a common
way to control all alternate functions.
Note that this improvement does not support the old-fashioned way
used to control nomadik pins, namely the "nmk_config_pin()" function
and its derivatives.
Signed-off-by: Jean-Nicolas Graux <jean-nicolas.graux@stericsson.com>
Reviewed-by: Philippe Langlais <philippe.langlais@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull MIPS update from Ralf Baechle:
"This is the MIPS update for 3.7.
A fair chunk of them are platform updates to the Cavium Octeon SOC
(which involves machine generated header files of considerable size),
Atheros ATH79xx, RMI aka Netlogic aka Broadcom XLP, Broadcom BCM63xx
platforms.
Support for the commercial MIPS simulator MIPSsim has been removed as
MIPS Technologies is shifting away from this product and Qemu is
offering various more powerful platforms. The generic MIPS code can
now also probe for no-execute / write-only TLB features implemented
without the full SmartMIPS extension as permitted by the latest MIPS
processor architecture. Lots of small changes to generic code."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (78 commits)
MIPS: ath79: Fix CPU/DDR frequency calculation for SRIF PLLs
MIPS: ath79: use correct fractional dividers for {CPU,DDR}_PLL on AR934x
MIPS: BCM63XX: Properly handle mac address octet overflow
MIPS: Kconfig: Avoid build errors by hiding USE_OF from the user.
MIPS: Replace `-' in defconfig filename wth `_' for consistency.
MIPS: Wire kcmp syscall.
MIPS: MIPSsim: Remove the MIPSsim platform.
MIPS: NOTIFY_RESUME is not needed in TIF masks
MIPS: Merge the identical "return from syscall" per-ABI code
MIPS: Unobfuscate _TIF..._MASK
MIPS: Prevent hitting do_notify_resume() with !user_mode(regs).
MIPS: Replace 'kernel_uses_smartmips_rixi' with 'cpu_has_rixi'.
MIPS: Add base architecture support for RI and XI.
MIPS: Optimise TLB handlers for MIPS32/64 R2 cores.
MIPS: uasm: Add INS and EXT instructions.
MIPS: Avoid pipeline stalls on some MIPS32R2 cores.
MIPS: Make VPE count to be one-based.
MIPS: Add new end of interrupt functionality for GIC.
MIPS: Add EIC support for GIC.
MIPS: Code clean-ups for the GIC.
...
This branch contains updates to OMAP and Marvell platforms (kirkwood,
dove, mvebu) that came in after we had done the big multiplatform merges,
so they were kept separate from the rest, and not separated into the
traditional topics of cleanup/driver/platform features.
For OMAP, the updates are:
- Runtime PM conversions for the GPMC and RNG IP blocks
- Preparation patches for the OMAP common clock framework conversion
- clkdev alias additions required by other drivers
- Performance Monitoring Unit (PMU) support for OMAP2, 3, and non-4430 OMAP4
- OMAP hwmod code and data improvements
- Preparation patches for the IOMMU runtime PM conversion
- Preparation patches for OMAP4 full-chip retention support
For Kirkwood/Dove/mvebu:
- New driver for "address decoder controller" for mvebu, which
is a piece of hardware that configures addressable devices and
peripherals. First user is the boot rom aperture on armada XP since
it is needed for SMP support.
- New device tree bindings for peripherals such as gpio-fan, iconnect
nand, mv_cesa and the above address decoder controller.
- Some defconfig updates, mostly to enable new DT boards and a few drivers.
- New drivers using the pincontrol subsystem for dove, kirkwood and mvebu
- New clean gpio driver for mvebu
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=xVaJ
-----END PGP SIGNATURE-----
Merge tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM soc platform updates from Olof Johansson:
"This branch contains updates to OMAP and Marvell platforms (kirkwood,
dove, mvebu) that came in after we had done the big multiplatform
merges, so they were kept separate from the rest, and not separated
into the traditional topics of cleanup/driver/platform features.
For OMAP, the updates are:
- Runtime PM conversions for the GPMC and RNG IP blocks
- Preparation patches for the OMAP common clock framework conversion
- clkdev alias additions required by other drivers
- Performance Monitoring Unit (PMU) support for OMAP2, 3, and
non-4430 OMAP4
- OMAP hwmod code and data improvements
- Preparation patches for the IOMMU runtime PM conversion
- Preparation patches for OMAP4 full-chip retention support
For Kirkwood/Dove/mvebu:
- New driver for "address decoder controller" for mvebu, which is a
piece of hardware that configures addressable devices and
peripherals. First user is the boot rom aperture on armada XP
since it is needed for SMP support.
- New device tree bindings for peripherals such as gpio-fan, iconnect
nand, mv_cesa and the above address decoder controller.
- Some defconfig updates, mostly to enable new DT boards and a few
drivers.
- New drivers using the pincontrol subsystem for dove, kirkwood and
mvebu
- New clean gpio driver for mvebu"
* tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (98 commits)
ARM: mvebu: fix build breaks from multi-platform conversion
ARM: OMAP4460/4470: PMU: Enable PMU for OMAP4460/70
ARM: OMAP2+: PMU: Add runtime PM support
ARM: OMAP4430: PMU: prepare to create PMU device via HWMOD
ARM: OMAP2+: PMU: Convert OMAP2/3 devices to use HWMOD
ARM: OMAP3: hwmod data: Add debugss HWMOD data
ARM: OMAP2+: clockdomain/hwmod: add workaround for EMU clockdomain idle problems
ARM: OMAP: Add a timer attribute for timers that can interrupt the DSP
hwrng: OMAP: remove SoC restrictions from driver registration
ARM: OMAP: split OMAP1, OMAP2+ RNG device registration
hwrng: OMAP: convert to use runtime PM
hwrng: OMAP: store per-device data in per-device variables, not file statics
ARM: OMAP2xxx: hwmod/CM: add RNG integration data
ARM: OMAP2+: gpmc: minimal driver support
ARM: OMAP2+: gpmc: Adapt to HWMOD
ARM: OMAP2/3: hwmod data: add gpmc
ARM: OMAP4: hwmod data: add mmu hwmod for ipu and dsp
ARM: OMAP3: hwmod data: add mmu data for iva and isp
ARM: OMAP: iommu: fix including iommu.h without IOMMU_API selected
ARM: OMAP4: hwmod data: add missing HWMOD_NO_IDLEST flags to some PRCM IP blocks
...
- Add subdrivers for the DB8540 and NHK8815 Nomadik-type ASICs,
provide platform config for the Nomadik.
- Add a driver for the i.MX35.
- Add a driver for the BCM2835, an advanced GPIO expander.
- Various fixes and clean-ups and minor improvements for the core,
Nomadik, pinctr-single, sirf drivers.
- Some platform config for the ux500.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=g2i2
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl changes from Linus Walleij:
"Some of this stuff is hitting arch/arm/* and have been ACKed by the
ARM SoC folks, or it's device tree bindings pertaining to the specific
driver.
These are the bulk pinctrl changes for kernel v3.7:
- Add subdrivers for the DB8540 and NHK8815 Nomadik-type ASICs,
provide platform config for the Nomadik.
- Add a driver for the i.MX35.
- Add a driver for the BCM2835, an advanced GPIO expander.
- Various fixes and clean-ups and minor improvements for the core,
Nomadik, pinctr-single, sirf drivers.
- Some platform config for the ux500."
* tag 'pinctrl-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (27 commits)
pinctrl: add bcm2835 driver
pinctrl: clarify idle vs sleep states
pinctrl/nomadik: use irq_find_mapping()
pinctrl: sirf: add lost chained_irq_enter and exit in sirfsoc_gpio_handle_irq
pinctrl: sirf: initialize the irq_chip pointer of pinctrl_gpio_range
pinctrl: sirf: fix spinlock deadlock in sirfsoc_gpio_set_input
pinctrl: sirf: add missing pins to pinctrl list
pinctrl: sirf: fix a typo in sirfsoc_gpio_probe
pinctrl: pinctrl-single: add debugfs pin h/w state info
ARM: ux500: 8500: update I2C sleep states pinctrl
pinctrl: Fix potential memory leak in pinctrl_register_one_pin()
ARM: ux500: tidy up pin sleep modes
ARM: ux500: fix spi2 pin group
pinctrl: imx: remove duplicated const
pinctrl: document semantics vs GPIO
ARM: ux500: 8500: use hsit_a_2 group for HSI
pinctrl: use kasprintf() in pinmux_request_gpio()
pinctrl: pinctrl-single: Add pinctrl-single,bits type of mux
pinctrl/nomadik : add MC1_a_2 pin MC1 function group list
pinctrl: pinctrl-single: Make sure we do not change bits outside of mask
...
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ck7M
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc driver specific changes from Olof Johansson:
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
Fix up conflicts as per Olof.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
drivers: bus: omap_l3: use resources instead of hardcoded irqs
pinctrl: exynos: Fix wakeup IRQ domain registration check
pinctrl: samsung: Uninline samsung_pinctrl_get_soc_data
pinctrl: exynos: Correct the detection of wakeup-eint node
pinctrl: exynos: Mark exynos_irq_demux_eint as inline
pinctrl: exynos: Handle only unmasked wakeup interrupts
pinctrl: exynos: Fix typos in gpio/wkup _irq_mask
pinctrl: exynos: Set pin function to EINT in irq_set_type of GPIO EINTa
drivers: bus: Move the OMAP interconnect driver to drivers/bus/
i2c: tegra: dynamically control fast clk
i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
ARM: tegra: clock: remove unused clock entry for i2c
ARM: tegra: clock: add connection name in i2c clock entry
i2c: tegra: pass proper name for getting clock
ARM: tegra: clock: add i2c fast clock entry in clock table
ARM: EXYNOS: Adds G-Scaler device from Device Tree
ARM: EXYNOS: Add clock support for G-Scaler
ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
...
A shorter cleanup branch submitted separately due to dependencies with
some of the previous topics.
Major thing here is that the Broadcom bcmring platform is removed. It's an
SoC that's used on some stationary VoIP platforms, and is in desperate
need of some cleanup. Broadcom came back and suggested that we just
deprecate the platform for now, since they aren't going to spend the
resources needed on cleaning it up, and there are no users of the platform
directly from mainline.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=LPF/
-----END PGP SIGNATURE-----
Merge tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc cleanups, part 2 from Olof Johansson:
"A shorter cleanup branch submitted separately due to dependencies with
some of the previous topics.
Major thing here is that the Broadcom bcmring platform is removed.
It's an SoC that's used on some stationary VoIP platforms, and is in
desperate need of some cleanup. Broadcom came back and suggested that
we just deprecate the platform for now, since they aren't going to
spend the resources needed on cleaning it up, and there are no users
of the platform directly from mainline."
Fix some conflicts due to BCM2835 getting added next to the removed
BCMRING, and removal of tegra files that had been converted to
devicetree.
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: Orion5x: ts78xx: Add IOMEM for virtual addresses.
ARM: ux500: use __iomem pointers for MMIO
ARM: Remove mach-bcmring
ARM: clps711x: Remove board support for CEIVA
ARM: clps711x: Fix register definitions
ARM: clps711x: Fix lowlevel debug-macro
ARM: clps711x: Added simple clock framework
pinctrl: tegra: move pinconf-tegra.h content into drivers/pinctrl
ARM: tegra: delete unused headers
ARM: tegra: remove useless includes of <mach/*.h>
ARM: tegra: remove dead code
Device tree conversion and enablement branch. Mostly a bunch of new
bindings and setup for various platforms, but the Via/Winchip VT8500
platform is also converted over from being 100% legacy to now use
device tree for probing. More of that will come for 3.8.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=q7ZY
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc device tree updates from Olof Johansson:
"Device tree conversion and enablement branch. Mostly a bunch of new
bindings and setup for various platforms, but the Via/Winchip VT8500
platform is also converted over from being 100% legacy to now use
device tree for probing. More of that will come for 3.8."
Trivial conflicts due to removal of vt8500 files, and one documentation
file that was added with slightly different contents both here and in
the USb tree.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (212 commits)
arm: vt8500: Fixup for missing gpio.h
ARM: LPC32xx: LED fix in PHY3250 DTS file
ARM: dt: mmp-dma: add binding file
arm: vt8500: Update arch-vt8500 to devicetree support.
arm: vt8500: gpio: Devicetree support for arch-vt8500
arm: vt8500: doc: Add device tree bindings for arch-vt8500 devices
arm: vt8500: clk: Add Common Clock Framework support
video: vt8500: Add devicetree support for vt8500-fb and wm8505-fb
serial: vt8500: Add devicetree support for vt8500-serial
rtc: vt8500: Add devicetree support for vt8500-rtc
arm: vt8500: Add device tree files for VIA/Wondermedia SoC's
ARM: tegra: Add Avionic Design Tamonten Evaluation Carrier support
ARM: tegra: Add Avionic Design Medcom-Wide support
ARM: tegra: Add Avionic Design Plutux support
ARM: tegra: Add Avionic Design Tamonten support
ARM: tegra: dts: Add pwm label
ARM: ux500: Fix SSP register address format
ARM: ux500: Apply tc3589x's GPIO/IRQ properties to HREF's DT
ARM: ux500: Remove redundant #gpio-cell properties from Snowball DT
ARM: ux500: Add all encompassing sound node to the HREF Device Tree
...
The BCM2835 GPIO module is a combined GPIO controller, (GPIO) interrupt
controller, and pinmux/control device.
Original driver by Simon Arlott.
Rewrite including GPIO chip device by Chris Boot.
Upstreaming changes by Stephen Warren:
* Wrote DT binding documentation.
* Changed brcm,function to an integer to more directly match the
datasheet, and to match brcm,pins being an integer.
* Implemented pull-up/down pin config.
* Removed read-only DT property and related code. The restriction this
implemented are driven by the board, not the GPIO HW block, so don't
really make sense of a HW block binding, were in general incomplete
(since they could only know about the few pins hard-coded into the
Raspberry Pi B board design and not the uncommitted GPIOS), and are
better represented simply by not writing incorrect data into pin
configuration nodes.
* Don't set GPIO_IN function select in gpio_request_enable() to avoid
glitches; defer this to gpio_set_direction(). Consequently, removed
empty bcm2835_pmx_gpio_request_enable().
* Simplified enabled_irq_map[]; make it explicitly 1 entry per bank.
* Lifted use of enabled_irq_map[] outside the per-interrupt loop in
IRQ handler, thus fixing an issue where the code was indexing into
enabled_irq_map[] by intra-bank GPIO ID, not global GPIO ID.
* Removed locking in IRQ handler, since all other code uses
spin_lock_irqsave() and so guarantees it doesn't run concurrently
with the handler.
* Moved duplicated BUILD_BUG_ON()s into probe(). Also check size of
bcm2835_gpio_pins[].
* Remove range-checking from bcm2835_pctl_get_groups_count() since we've
decided to trust the pinctrl core.
* Made bcm2835_pmx_gpio_disable_free() call bcm2835_pinctrl_fsel_set()
directly for simplicity.
* Fixed body of dt_free_map() to match latest dt_node_to_map().
* Removed GPIO ownership check from bcm2835_pmx_enable() since the pinctrl
core owns doing this.
* Made irq_chip and pinctrl_gpio_range .name == MODULE_NAME so it's more
descriptive.
* Simplified remove(); removed call to non-existent
pinctrl_remove_gpio_range(), remove early return on error.
* Don't force gpiochip's base to 0. Set gpio_range.base to gpiochip's
base GPIO number.
* Error-handling cleanups in probe().
* Switched to module_platform_driver() rather than open-coding.
* Made pin, group, and function names lower-case.
* s/broadcom/brcm/ in DT property names.
* s/2708/2835/.
* Fixed a couple minor checkpatch warnings, and other minor cleanup.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The code was using a homegrown method of looking up the offset
from the irq domain, not to be encouraged. Use the proper
irq_find_mapping() call instead.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch initializes the optional irq_chip pointer gc in sirfsoc
pinctrl_gpio_range.
Signed-off-by: Baohua Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
sirfsoc_gpio_set_input() is called in those functions which have
held the spinlock, so delete the duplicated locking.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We always use pinctrl_request_gpio() to get GPIO, If we don't have these
missing pins in the pin list, gpio_request and related operations will fail
for them.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds support for displaying the individual pin h/w config state.
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
'pindesc' was not freed when returning from an error induced
exit path.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
From Jason Cooper:
New drivers:
- pinctrl (dove, kirkwood, mvebu)
- gpio (mvebu)
* 'kirkwood/drivers' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: add gpio support in defconfig
arm: mvebu: add DT information for GPIO banks on Armada 370 and XP
arm: mvebu: use GPIO support now that a driver is available
Documentation: add description of DT binding for the gpio-mvebu driver
gpio: introduce gpio-mvebu driver for Marvell SoCs
arm: mvebu: select the pinctrl drivers for Armada 370 and Armada XP platforms
arm: mvebu: split Kconfig options for Armada 370 and XP
ARM: mvebu: adjust Armada XP evaluation board DTS
ARM: mvebu: Add pinctrl support to Armada 370 SoC
ARM: mvebu: Add pinctrl support to Armada XP SoCs
pinctrl: mvebu: add pinctrl driver for Armada XP
pinctrl: mvebu: add pinctrl driver for Armada 370
pinctrl: mvebu: kirkwood pinctrl driver
pinctrl: mvebu: dove pinctrl driver
pinctrl: mvebu: pinctrl driver core
Signed-off-by: Olof Johansson <olof@lixom.net>
This pinctrl driver is not a full-blown pinctrl driver from scratch:
it relies on the common pinctrl-mvebu driver, which is used for all
Marvell EBU SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This pinctrl driver is not a full-blown pinctrl driver from scratch:
it relies on the common pinctrl-mvebu driver, which is used for all
Marvell EBU SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds a SoC specific pinctrl driver for Marvell Kirkwood SoCs
plus DT binding documentation. This driver will use the mvebu pinctrl
driver core.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds a SoC specific pinctrl driver for Marvell Dove SoCs
plus DT binding documentation. This driver will use the mvebu pinctrl
driver core.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds a pinctrl driver core for Marvell SoCs plus DT
binding documentation. This core driver will be used by SoC family
specific drivers, i.e. Armada XP, Armada 370, Dove, Kirkwood, aso.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Conflicts:
arch/arm/Kconfig
Because of a typo, incorrect field of a structure was being checked.
This patch fixes the check to use correct field.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Although the function is used only a single time, it is not performance
critical and it is pretty heavy, so let the compiler decide whether to
inline it instead.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Current way of finding the wakeup-eint node scans the whole device tree
not only children of the pinctrl node, so it might detect a wakeup-eint
node of another pinctrl device.
This patch limits the scope of looking for nodes only to subnodes of the
pinctrl node.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The exynos_irq_demux_eint utility function is used in chained IRQ
handler for EINT16-31 to handle multiplexed interrupts. Inlining it
should improve the performance a bit.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
A bit in EINTxx_PEND register is set regardless of interrupt mask, which
causes spurious interrupts. To avoid them, the read value of pending
register must be masked with current interrupt mask manually.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
To mask GPIO/wakeup IRQ, the corresponding bit in mask register has to
be set.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Pins used as GPIO interrupts need to be configured as EINTs. This patch
adds the required configuration code to exynos_gpio_irq_set_type,
to set the pin as EINT when its interrupt trigger is configured.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Now that Tegra's pinmux is configured solely from device tree, there's
no need for the pinconf types to be defined in arch/arm/mach-tegra/.
Move it into the pinctrl directory to clean up mach-tegra, as a pre-
requisite for single-zImage.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Instead of using a temporary buffer, snprintf() and kstrdup(), just
use kasprintf() that does the same thing in just oneline.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Colin Cross <ccross@google.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Implement support for pinctrl on lantiq/falcon socs. The FALCON has 5 banks
of up to 32 pins.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Implement support for pinctrl on lantiq/xway socs. The IO core found on these
socs has the registers for pinctrl, pinconf and gpio mixed up in the same
register range. As the gpio_chip handling is only a few lines, the driver also
implements the gpio functionality. This obseletes the old gpio driver that was
located in the arch/ folder.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
With pinctrl-single,bits it is possible to update just part of the register
within the pinctrl-single,function-mask area.
This is useful when one register configures mmore than one pin's mux.
pinctrl-single,bits takes three parameters:
<reg offset, value, sub-mask>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
[Removed a misplaced comment]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Another possible pin configuration for the MC1 pin group.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the pcs->fmask to make sure that the value is not changing (setting)
bits in areas where it should not.
To avoid situations like this:
pmx_dummy: pinmux@4a100040 {
compatible = "pinctrl-single";
reg = <0x4a100040 0x0196>;
#address-cells = <1>;
#size-cells = <0>;
pinctrl-single,register-width = <16>;
pinctrl-single,function-mask = <0x00ff>;
};
&pmx_dummy {
pinctrl-names = "default";
pinctrl-0 = <&board_pins>;
board_pins: pinmux_board_pins {
pinctrl-single,pins = <
0x6c 0xf0f
0x6e 0x10f
0x70 0x23f
0x72 0xa5f
>;
};
};
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add information about the Exynos4210 pin banks and driver data which is
used by the Samsung pinctrl driver. In addition to this, the support for
external gpio and wakeup interrupt support is included and hooked up with
the Samsung pinctrl driver.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add a new device tree enabled pinctrl and gpiolib driver for Samsung
SoC's. This driver provides a common and extensible framework for all
Samsung SoC's to interface with the pinctrl and gpiolib subsystems. This
driver supports only device tree based instantiation and hence can be
used only on those Samsung platforms that have device tree enabled.
This driver is split into two parts: the pinctrl interface and the gpiolib
interface. The pinctrl interface registers pinctrl devices with the pinctrl
subsystem and gpiolib interface registers gpio chips with the gpiolib
subsystem. The information about the pins, pin groups, pin functions and
gpio chips, which are SoC specific, are parsed from device tree node.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This makes us possible to define pinmux mapping in board-specific DTS.
prima2.dtsi provides all possible (groups,functions) configuration, and
device in .dts select configurations from dtsi files.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The io-pci series has gained a merge to resolve a nontrivial
conflict.
* cleanup/io-pci:
ARM: Fix ioremap() of address zero
Also includes an update to Linux 3.6-rc3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ux500 machines performs pins (GPIO) reconfiguration when entering
in the suspended mode. This reconfiguration aims at reaching an ultra
low power HW configuration.
Due to this HW reconfiguration, some HW devices can change of HW state
and have their output signals at level that could generate IRQs.
If the non-wakeup IRQs are disabled but not yet masked (delayed interrupt
disable feature from the generic irq layer), effective interrupts reach
the system only because the system attempt to enter the suspended mode.
To prevent such IRQs to trig, all irq chips embedded in ux500 platform
should enable their IRQCHIP_MASK_ON_SUSPEND flag.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Unlike imx6q pinctrl driver that starts nubmering pad from 0, imx5
pinctrl drivers number pad from 1. It causes problem/confusion when
driver accesses imx51_pinctrl_pads array using pin ID as the index.
Change imx51_pads and imx53_pads numbering start from 0.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is mostly cut'n'paste from the imx51 pinctrl driver.
The data was generated using sed and awk on
arch/arm/plat-mxc/include/mach/iomux-mx35.h.
Changes since (implicit) v1
- remove references to file names in binding documentation
- remove sed commands from comments in driver
- add explicit numbers for pins and functions
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the STN8815 ASIC for the Nomadik pin
controller.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This implements a subdriver for the DB8540 ASIC for the
Nomadik pin controller.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is yet another way to mux the keyboard, so fix up that
group.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .conf_reg of MX51_PAD_SD2_CMD__CSPI_MOSI should be 0x7bc rather
than NO_PAD. This error will cause SD2 probe failure.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij