When Tegra PCIe is in endpoint mode it should be available for root port.
PCIe link up by root port fails if it is in suspend state. So, don't allow
Tegra to suspend when endpoint mode is enabled.
Link: https://lore.kernel.org/r/20210623100525.19944-5-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
In suspend_noirq() call if link doesn't goto L2, PERST# is asserted
to bring link to detect state. However, this is causing surprise
link down AER error. Since Kernel is executing noirq suspend calls,
AER interrupt is not processed. PME and AER are shared interrupts
and PCIe subsystem driver enables wake capability of PME irq during
suspend. So this AER will cause suspend failure due to pending
AER interrupt.
After PCIe link is in L2, interrupts are not expected since PCIe
controller will be in reset state. Disable PCIe interrupts before
going to L2 state to avoid pending AER interrupt.
Link: https://lore.kernel.org/r/20210623100525.19944-4-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
Lower order MSI-X address is programmed in MSIX_ADDR_MATCH_HIGH_OFF
DBI register instead of higher order address. This patch fixes this
programming mistake.
Link: https://lore.kernel.org/r/20210623100525.19944-3-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
In tegra_pcie_ep_hard_irq(), APPL_INTR_STATUS_L0 is stored in val and again
APPL_INTR_STATUS_L1_0_0 is also stored in val. So when execution reaches
"if (val & APPL_INTR_STATUS_L0_PCI_CMD_EN_INT)", val is not correct.
Link: https://lore.kernel.org/r/20210623100525.19944-2-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
tegra_pcie_ep_raise_msi_irq() shifted a signed 32-bit value left by 31
bits. The behavior of this is implementation-defined.
Replace the shift by BIT(), which is well-defined.
Found by cppcheck:
$ cppcheck --enable=all drivers/pci/controller/dwc/pcie-tegra194.c
Checking drivers/pci/controller/dwc/pcie-tegra194.c ...
drivers/pci/controller/dwc/pcie-tegra194.c:1829:23: portability: Shifting signed 32-bit value by 31 bits is implementation-defined behaviour. See condition at line 1826. [shiftTooManyBitsSigned]
appl_writel(pcie, (1 << irq), APPL_MSI_CTRL_1);
^
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20210618160219.303092-1-jonathanh@nvidia.com
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 275e88b06a ("PCI: tegra: Fix host link initialization") broke
host initialization during resume as it misses out calling the API
dw_pcie_setup_rc() which is required for host and MSI initialization.
Link: https://lore.kernel.org/r/20210504172157.29712-1-vidyas@nvidia.com
Fixes: 275e88b06a ("PCI: tegra: Fix host link initialization")
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
7f10074474 ("PCI: tegra: Add Tegra194 MCFG quirks for ECAM errata")
caused a few build regressions:
- 7f10074474 removed the Makefile rule for CONFIG_PCIE_TEGRA194, so
pcie-tegra.c can no longer be built as a module. Restore that rule.
- 7f10074474 added "#ifdef CONFIG_PCIE_TEGRA194" around the native
driver, but that's only set when the driver is built-in (for a module,
CONFIG_PCIE_TEGRA194_MODULE is defined).
The ACPI quirk is completely independent of the rest of the native
driver, so move the quirk to its own file and remove the #ifdef in the
native driver.
- 7f10074474 added symbols that are always defined but used only when
CONFIG_PCIEASPM, which causes warnings when CONFIG_PCIEASPM is not set:
drivers/pci/controller/dwc/pcie-tegra194.c:259:18: warning: ‘event_cntr_data_offset’ defined but not used [-Wunused-const-variable=]
drivers/pci/controller/dwc/pcie-tegra194.c:250:18: warning: ‘event_cntr_ctrl_offset’ defined but not used [-Wunused-const-variable=]
drivers/pci/controller/dwc/pcie-tegra194.c:243:27: warning: ‘pcie_gen_freq’ defined but not used [-Wunused-const-variable=]
Fixes: 7f10074474 ("PCI: tegra: Add Tegra194 MCFG quirks for ECAM errata")
Link: https://lore.kernel.org/r/20210610064134.336781-1-jonathanh@nvidia.com
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
The PCIe controller in Tegra194 SoC is not ECAM-compliant. With the
current hardware design, ECAM can be enabled only for one controller (the
C5 controller) with bus numbers starting from 160 instead of 0. A different
approach is taken to avoid this abnormal way of enabling ECAM for just one
controller but to enable configuration space access for all the other
controllers. In this approach, ops are added through MCFG quirk mechanism
which access the configuration spaces by dynamically programming iATU
(internal AddressTranslation Unit) to generate respective configuration
accesses just like the way it is done in DesignWare core sub-system.
This issue is specific to Tegra194 and it would be fixed in the future
generations of Tegra SoCs.
Link: https://lore.kernel.org/r/20210416134537.19474-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pm_runtime_get_sync() will increase the runtime PM counter
even it returns an error. Thus a pairing decrement is needed
to prevent refcount leak. Fix this by replacing this API with
pm_runtime_resume_and_get(), which will not change the runtime
PM counter on error.
Link: https://lore.kernel.org/r/20210408072700.15791-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
The only usage of them is to assign their address to the 'ops' field in
the pcie_port and the dw_pcie_ep structs, both which are pointers to
const. Make them const to allow the compiler to put them in read-only
memory.
Link: https://lore.kernel.org/r/20210207221604.48910-1-rikard.falkeborn@gmail.com
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Commit b9ac0f9dc8 ("PCI: dwc: Move dw_pcie_setup_rc() to DWC common
code") broke enumeration of downstream devices on Tegra:
In non-working case (next-20201211):
0001:00:00.0 PCI bridge: NVIDIA Corporation Device 1ad2 (rev a1)
0001:01:00.0 SATA controller: Marvell Technology Group Ltd. Device 9171 (rev 13)
0005:00:00.0 PCI bridge: NVIDIA Corporation Device 1ad0 (rev a1)
In working case (v5.10-rc7):
0001:00:00.0 PCI bridge: Molex Incorporated Device 1ad2 (rev a1)
0001:01:00.0 SATA controller: Marvell Technology Group Ltd. Device 9171 (rev 13)
0005:00:00.0 PCI bridge: Molex Incorporated Device 1ad0 (rev a1)
0005:01:00.0 PCI bridge: PLX Technology, Inc. Device 3380 (rev ab)
0005:02:02.0 PCI bridge: PLX Technology, Inc. Device 3380 (rev ab)
0005:03:00.0 USB controller: PLX Technology, Inc. Device 3380 (rev ab)
The problem seems to be dw_pcie_setup_rc() is now called twice before and
after the link up handling. The fix is to move Tegra's link up handling to
.start_link() function like other DWC drivers. Tegra is a bit more
complicated than others as it re-inits the whole DWC controller to retry
the link. With this, the initialization ordering is restored to match the
prior sequence.
Fixes: b9ac0f9dc8 ("PCI: dwc: Move dw_pcie_setup_rc() to DWC common code")
Link: https://lore.kernel.org/r/20201218143905.1614098-1-robh@kernel.org
Reported-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Tested-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Vidya Sagar <vidyas@nvidia.com>
PCIe cards like Marvell SATA controller and some of the Samsung NVMe
drives don't support taking the link to L2 state. When the link doesn't
go to L2 state, Tegra194 requires the LTSSM to be disabled to allow PHY
to start the next link up process cleanly during suspend/resume sequence.
Failing to disable LTSSM results in the PCIe link not coming up in the
next resume cycle.
Link: https://lore.kernel.org/r/20201203133451.17716-6-vidyas@nvidia.com
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
The return value of tegra_pcie_init_controller() must be checked before
PCIe link up check and registering debugfs entries subsequently as it
doesn't make sense to do these when the controller initialization itself
has failed.
Link: https://lore.kernel.org/r/20201203133451.17716-5-vidyas@nvidia.com
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Currently the driver checks for error value of different APIs during the
uninitialization sequence. It just returns from there if there is any error
observed for one of those calls. Comparatively it is better to continue the
uninitialization sequence irrespective of whether some of them are
returning error. That way, it is more closer to complete uninitialization.
Link: https://lore.kernel.org/r/20201203133451.17716-4-vidyas@nvidia.com
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Set the DesignWare IP version for Tegra194 to 0x490A. This would be used
by the DesigWare sub-system to do any version specific configuration
(Ex:- TD bit programming for ECRC).
Link: https://lore.kernel.org/r/20201203133451.17716-3-vidyas@nvidia.com
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
If the absence of CLKREQ# signal is indicated by the absence of
"supports-clkreq" in the device-tree node, current driver is disabling
the advertisement of ASPM-L1 Sub-States *before* the ASPM-L1 Sub-States
offset is correctly initialized. Since default value of the ASPM-L1SS
offset is zero, this is causing the Vendor-ID wrongly programmed to 0x10d2
instead of Nvidia's 0x10de thereby the quirks applicable for Tegra194 are
not being applied. This patch fixes this issue by refactoring the
code that disables the ASPM-L1SS advertisement.
Link: https://lore.kernel.org/r/20201203133451.17716-2-vidyas@nvidia.com
Fixes: 56e15a238d ("PCI: tegra: Add Tegra194 PCIe support")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
PCIe controller in Tegra194 requires the "dbi" region base address to be
programmed in one of the application logic registers to enable CPU access
to the "dbi" region. But, commit a0fd361db8 ("PCI: dwc: Move "dbi",
"dbi2", and "addr_space" resource setup into common code") moved the code
that reads the whereabouts of "dbi" region to the common code causing the
existing code in pcie-tegra194.c file to program NULL in the application
logic registers. This is causing null pointer dereference when the "dbi"
registers are accessed. This issue is fixed by explicitly reading the
"dbi" base address from DT node.
Link: https://lore.kernel.org/r/20201125192554.5401-1-vidyas@nvidia.com
Fixes: a0fd361db8 ("PCI: dwc: Move "dbi", "dbi2", and "addr_space" resource setup into common code")
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
commit a0fd361db8 ("PCI: dwc: Move "dbi", "dbi2", and "addr_space"
resource setup into common code") moved the code that sets up dbi_base
to DWC common code thereby creating a requirement to not access the "dbi"
region before calling common DWC initialization code. But, Tegra194
already had some code that programs some of the "dbi" registers resulting
in system crash. This patch addresses that issue by refactoring the code
to have accesses to the "dbi" region only after common DWC initialization.
Link: https://lore.kernel.org/r/20201125192234.2270-1-vidyas@nvidia.com
Fixes: a0fd361db8 ("PCI: dwc: Move "dbi", "dbi2", and "addr_space" resource setup into common code")
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Currently the number of inbound and outbound iATU windows are determined
from DT properties. Unfortunately, there's 'num-viewport' for RC mode
and 'num-ib-windows' and 'num-ob-windows' for EP mode, yet the number of
windows is not mode dependent. Also, 'num-viewport' is not clear whether
that's inbound, outbound or both. We can probably assume it's outbound
windows as that's all RC mode uses.
However, using DT properties isn't really needed as the number of
regions can be detected at runtime by poking the iATU registers. The
basic algorithm is just writing a target address and reading back what
we wrote. In the unrolled ATU case, we have to take care not to go
past the mapped region.
With this, we can drop num_viewport in favor of num_ob_windows instead.
Link: https://lore.kernel.org/r/20201105211159.1814485-17-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
All the DWC drivers do link setup and checks at roughly the same time.
Let's use the existing .start_link() hook (currently only used in EP
mode) and move the link handling to the core code.
The behavior for a link down was inconsistent as some drivers would fail
probe in that case while others succeed. Let's standardize this to
succeed as there are usecases where devices (and the link) appear later
even without hotplug. For example, a reconfigured FPGA device.
Link: https://lore.kernel.org/r/20201105211159.1814485-11-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@axis.com
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Platforms using the built-in DWC MSI controller all have a dedicated
interrupt with "msi" name or at index 0, so let's move setting up the
interrupt to the common DWC code.
spear13xx and dra7xx are the 2 oddballs with muxed interrupts, so
we need to prevent configuring the MSI interrupt by setting msi_irq
to negative.
Link: https://lore.kernel.org/r/20201105211159.1814485-9-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@axis.com
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
There's no reason for the .set_num_vectors() host op. Drivers needing a
non-default value can just initialize pcie_port.num_vectors directly.
Link: https://lore.kernel.org/r/20201105211159.1814485-8-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Most DWC drivers use the common register resource names "dbi", "dbi2", and
"addr_space", so let's move their setup into the DWC common code.
This means 'dbi_base' in particular is setup later, but it looks like no
drivers touch DBI registers before dw_pcie_host_init or dw_pcie_ep_init.
Link: https://lore.kernel.org/r/20201105211159.1814485-4-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Minghuan Lian <minghuan.Lian@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Roy Zang <roy.zang@nxp.com>
Cc: Jonathan Chocron <jonnyc@amazon.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-omap@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-arm-kernel@axis.com
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
- Drop return value checking for debugfs_create() calls (Greg
Kroah-Hartman)
- Convert debugfs "ports" file to use DEFINE_SEQ_ATTRIBUTE() (Liu Shixin)
* remotes/lorenzo/pci/tegra:
PCI: tegra: Convert to use DEFINE_SEQ_ATTRIBUTE macro
PCI: tegra: No need to check return value of debugfs_create() functions
Convert the remaining cases of register accesses using dbi_base rather
than dw_pcie_(read|write)[bwl]_dbi accessors.
Link: https://lore.kernel.org/r/20200821035420.380495-41-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
The Designware controller has common registers to set number of fast
training sequence ordered sets. The Artpec6, Intel, and Tegra driver
initialize these register fields. Let's move the initialization to the
common setup code and drivers just have to provide the value.
There's a slight change in that the common clock mode N_FTS field is
now initialized. Previously only the Intel driver set this. It's not
clear from the code if common clock mode is used in the Artpec6 or Tegra
driver. It depends on the DWC configuration. Given the field is not
initialized while the others are, it seems unlikely common clock mode
is used.
Link: https://lore.kernel.org/r/20200821035420.380495-40-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
The Tegra driver has its own defines for common Designware Port Logic
registers. Convert it to use the standard register definitions.
Link: https://lore.kernel.org/r/20200821035420.380495-32-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
The pci_host_bridge struct already has a pointer to its pci_bus, so
let's convert the one user to use the bridge struct and remove the
private 'root_bus' pointer.
Link: https://lore.kernel.org/r/20200821035420.380495-18-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the Tegra driver to use the standard pci_ops for root
bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-8-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Link: https://lore.kernel.org/r/20200818133739.463193-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Vidya Sagar <vidyas@nvidia.com>
Cc: Andrew Murray <amurray@thegoodpenguin.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-pci@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Link: https://lore.kernel.org/r/20200521031355.7022-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
The platform_get_irq*() interfaces return either a negative error number or
a valid IRQ. 0 is not a valid return value, so check for "< 0" to detect
failure as recommended by the function documentation.
On failure, return the error number from platform_get_irq*() instead of
making up a new one.
Link: https://lore.kernel.org/r/cover.1583952275.git.amanharitsh123@gmail.com
[bhelgaas: commit log, squash into one patch]
Signed-off-by: Aman Sharma <amanharitsh123@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Probe deferral is an expected error condition that will usually be
recovered from. Print such error messages at debug level to make them
available for diagnostic purposes when building with debugging enabled
and hide them otherwise to not spam the kernel log with them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Tested-by: Vidya Sagar <vidyas@nvidia.com>
Add support for the endpoint mode of Synopsys DesignWare core based
dual mode PCIe controllers present in Tegra194 SoC.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Corrects the programming to provide REFCLK to the downstream device
when there is no CLKREQ sideband signal routing present from root port
to the endpont.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Add support to get regulator information of 3.3V and 12V supplies of a PCIe
slot from the respective controller's device-tree node and enable those
supplies. This is required in platforms like p2972-0000 where the supplies
to x16 slot owned by C5 controller need to be enabled before attempting to
enumerate the devices.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Add support to configure sideband signal pins when the information is
present in the respective controller device-tree node.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[bhelgaas: fold in YueHaibing's fix for build error without CONFIG_PINCTRL;
https://lore.kernel.org/r/20190920014807.38288-1-yuehaibing@huawei.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Add support for Synopsys DesignWare core IP based PCIe host controller
present in the Tegra194 SoC.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Om Prakash Singh