QCA6390 uses only 9 Copy Engines while IPQ8074 may use 12, make it possible to
change CE configuration dynamically via hw_params.
The defines for host_ce_config_wlan and CE_COUNT are temporary solutions, they
will be removed in the following patches to keep things simple.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-4-git-send-email-kvalo@codeaurora.org
Now some of the HAL register macros access ab variable in a hidden way, make ab
variable visible in the macro by adding it as an argument.
This is done in a separate patch to keep the patches simple. No functional changes.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-3-git-send-email-kvalo@codeaurora.org
QCA6390 has different register offset compared to IPQ8074, so need to
attach the register offset dynamically based on hw_params.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-2-git-send-email-kvalo@codeaurora.org
There's no reason to have call for enable_pll_clk in ath10k_bmi_start(), move
it to ath10k_core_start() instead. This way it's possible to call
ath10k_bmi_start() from sdio.c during firmware dump creation. And also the
function call is more visible when it's in core.c.
No functional changes, compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597421745-4329-1-git-send-email-kvalo@codeaurora.org
Qualcomm's document "80-WL007-1 Rev. J" states that the highest rx rate for
the WCN3660 and WCN3680 on MCS 7 is 150 Mbps not the 72 Mbps stated here.
This patch fixes the data-rate declared in the 5GHz table.
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680
hardware")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200802004824.1307124-1-bryan.odonoghue@linaro.org
Update the size used in 'dma_free_coherent()' in order to match the one
used in the corresponding 'dma_alloc_coherent()'.
Fixes: 1863008369 ("ath10k: fix shadow register implementation for WCN3990")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200802122227.678637-1-christophe.jaillet@wanadoo.fr
The value of "htc_hdr->endpoint_id" comes from skb->data so Smatch marks
it as untrusted so we have to check it before using it as an array
offset.
This is similar to a bug that syzkaller found in commit e4ff08a4d7
("ath9k: Fix use-after-free Write in ath9k_htc_rx_msg") so it is
probably a real issue.
Fixes: fb9987d0f7 ("ath9k_htc: Support for AR9271 chipset.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200813141253.GA457408@mwanda
The ath9k driver was so far only able to rekey PTK0 keys correctly due
to the best effort queue flush added with commit 62872a9b9a
("mac80211: Fix PTK rekey freezes and clear text leak").
Add the needed queue flush and set NL80211_EXT_FEATURE_CAN_REPLACE_PTK0
to tell mac80211 that the driver can now rekey PTK0 keys correctly and
no longer needs the best effort flush.
Effectively this prevents mac80211 to warn when rekeying a PTK0 key
only.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200804164152.175375-1-alexander@wetzel-home.de
The value for "aid" comes from skb->data so Smatch marks it as
untrusted. If it's invalid then it can result in an out of bounds array
access in ath6kl_add_new_sta().
Fixes: 572e27c00c ("ath6kl: Fix AP mode connect event parsing and TIM updates")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200813141315.GB457408@mwanda
Kerneldoc expects attributes/parameters to be in '@*.: ' format and
gets confused if the variable does not follow the type/attribute
definitions.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath5k/base.c:1111: warning: Function parameter or member 'ah' not described in 'ath5k_drain_tx_buffs'
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jesper Dangaard Brouer <hawk@kernel.org>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: "Luis R. Rodriguez" <mcgrof@winlab.rutgers.edu>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: bpf@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-21-lee.jones@linaro.org
No effort has been made to document any of the function parameters here.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/wil6210/cfg80211.c:1749: warning: Function parameter or member 'ies' not described in '_wil_cfg80211_find_ie'
drivers/net/wireless/ath/wil6210/cfg80211.c:1749: warning: Function parameter or member 'ies_len' not described in '_wil_cfg80211_find_ie'
drivers/net/wireless/ath/wil6210/cfg80211.c:1749: warning: Function parameter or member 'ie' not described in '_wil_cfg80211_find_ie'
drivers/net/wireless/ath/wil6210/cfg80211.c:1749: warning: Function parameter or member 'ie_len' not described in '_wil_cfg80211_find_ie'
drivers/net/wireless/ath/wil6210/cfg80211.c:1780: warning: Function parameter or member 'ies1' not described in '_wil_cfg80211_merge_extra_ies'
drivers/net/wireless/ath/wil6210/cfg80211.c:1780: warning: Function parameter or member 'ies1_len' not described in '_wil_cfg80211_merge_extra_ies'
drivers/net/wireless/ath/wil6210/cfg80211.c:1780: warning: Function parameter or member 'ies2' not described in '_wil_cfg80211_merge_extra_ies'
drivers/net/wireless/ath/wil6210/cfg80211.c:1780: warning: Function parameter or member 'ies2_len' not described in '_wil_cfg80211_merge_extra_ies'
drivers/net/wireless/ath/wil6210/cfg80211.c:1780: warning: Function parameter or member 'merged_ies' not described in '_wil_cfg80211_merge_extra_ies'
drivers/net/wireless/ath/wil6210/cfg80211.c:1780: warning: Function parameter or member 'merged_len' not described in '_wil_cfg80211_merge_extra_ies'
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: wil6210@qti.qualcomm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-14-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath5k/pcu.c:115: warning: Function parameter or member 'band' not described in 'ath5k_hw_get_frame_duration'
drivers/net/wireless/ath/ath5k/pcu.c:955: warning: Excess function parameter 'mode' description in 'ath5k_hw_pcu_init'
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Reyk Floeter <reyk@openbsd.org>
Cc: "W. S. Bell" <mentor@madwifi.org>
Cc: Luis Rodriguez <mcgrof@winlab.rutgers.edu>
Cc: Pavel Roskin <proski@gnu.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-10-lee.jones@linaro.org
On QCA6390 reg_start and reg_size values are different from IPQ8074 so we need
to change the values runtime. As we can't modify a static const variable
hw_srng_config directly, instead use it as a template, copy it and modify the
copy with correct values.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-12-git-send-email-kvalo@codeaurora.org
On x86 and other non-qcom platforms, host needs to explicitly tell the firmware
to use the internal sleep clock. Some QCA6390 modules have OTP burnt with
external sleep clock selected, and these modules can't work expectedly unless
firmware selects internal sleep clock.
Add a field to hw_params to support this difference.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-11-git-send-email-kvalo@codeaurora.org
It's caused by reading memory out of boundary from target_ce_config_wlan.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-10-git-send-email-kvalo@codeaurora.org
The decoded_size is wrongly assigned in ath11k_qmi_msg_handlers and it results
in out of boundary access in qmi_decode. The correct decoded_size should be
calculated from the related ind_msg structure.
This issue is exposed with QCA6390 because it needs 11 small memory chunks
which are stored in qmi_wlanfw_request_mem_ind_msg_v01 and hence the
decoded_size exceeds the wrongly assigend decoded_size.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-9-git-send-email-kvalo@codeaurora.org
On x86 it's sometimes difficult to allocate a large contigous DMA
memory, so instead allocate blocks of small chunk memory.
In ath11k_qmi_msg_mem_request_cb() the error handling was cleaned up to avoid
an unused variable warning. Also changed the test from (ret < 0) to just (ret)
as the functions don't return any positive values.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-8-git-send-email-kvalo@codeaurora.org
CE srng is used for control path and CE srng processing is done using tasklet
bottom half. Setup ce tasklet initialization and scheduling for control path.
Needed for PCI support.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-7-git-send-email-kvalo@codeaurora.org
Fill msi base address and msi data to be programmed in CE srang.
This is used by the srng to generate the msi interrupt.
Needed for PCI support.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-6-git-send-email-kvalo@codeaurora.org
QMI service instance id is used for qmi service lookup, IPQ8074 and QCA6390
uses different instance id for service lookup. Fill appropriate QMI service
instance id for respective targets.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-4-git-send-email-kvalo@codeaurora.org
PCI devices like QCA6390 load the board file differently, add support for that
and the method is chosen using bus_params variables.
Add support to create board name for different targets. This board name is
used to parse the board data from board-2.bin for ahb/pci based targets.
As struct target_mem_chunk::vaddr was changed from 'u32' to 'u32 *' in
ath11k_qmi_assign_target_mem_chunk() vaddr assignments were changed to NULL to
avoid a compilation warning. IPQ8074 does not use the vaddr field for anything
so that change does not affect functionality.
At the moment this only supports board files with BIN type. Support for ELF
type, which seems to be more popular on QCA6390 devices, needs to be added later.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-3-git-send-email-kvalo@codeaurora.org
PCI devices like QCA6390 have a separate firmware image for the m3
micro-controller. Add support to load the firmware using m3.bin file.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-2-git-send-email-kvalo@codeaurora.org
QCA6390 and other PCI devices use MHI based firmware loading and do not use
remoteproc, so enable it only for AHB devices.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-11-git-send-email-kvalo@codeaurora.org
Modem Host Interface (MHI) is a communication protocol to communicate with
external Qualcomm modems and Wi-Fi chipsets over high speed peripheral buses.
Even though MHI doesn’t dictate underlying physical layer, protocol and MHI
stack is structured for PCI based devices.
Register directly with MHI subsystem as a MHI device driver for firmware
download to QCA6390.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-9-git-send-email-kvalo@codeaurora.org
This is needed to initialise hw_params before MHI registration starts. MHI
needs location of firmware directory and that's delivered via hw_params.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-8-git-send-email-kvalo@codeaurora.org
Add support for setting up pci region and dma mask.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-6-git-send-email-kvalo@codeaurora.org
QCA6390 is a PCI based 11ax chipset, split AHB into own kernel module
ath11k_ahb.ko and add ath11k_pci.ko for PCI devices.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-5-git-send-email-kvalo@codeaurora.org
This is needed for splitting ahb and pci modules as they have different ring
mask settings.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-4-git-send-email-kvalo@codeaurora.org
Define own firmware directory and settings for QCA6390.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-3-git-send-email-kvalo@codeaurora.org
With only IPQ8074 supported ath11k was only usable on Qualcomm architectures.
But now that we are adding QCA6390 PCI support to ath11k that's not the case
anymore and it can be used on any architecture supporting PCI. So remove the
dependency on ARCH_QCOM. After that there is also no need to depend on
COMPILE_TEST.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-2-git-send-email-kvalo@codeaurora.org
The mcs index of HT mode is 0 to 31, please refer http://mcsindex.com/.
Its spatial stream(Nss) number is from 1 to 4, mcs index is 0~7 for
Nss=1, 8~15 for Nss=2, 16~23 for Nss=3 and 24~31 is for Nss=4.
The mcs is reported from firmware in wmi_tlv_peer_stats_info of
event WMI_TLV_PEER_STATS_INFO_EVENTID, its range is from 0~15 for
QCA6174 SDIO and PCIe. It is for both Nss=1 and Nss=2, and it has 2
rate table supported_ht_mcs_rate_nss1 and supported_ht_mcs_rate_nss2
in ath10k, they are for Nss=1 and Nss=2, each table has 8 rates.
It need to find the matched row number with the mcs index, for example,
mcs index is 2, it is <=7, so it is Nss=1, and match row 2 in table of
Nss=1. If mcs index is 12, it is >= 8 and <= 15, so it is Nss=2, it
match row 4(12-8) in table of Nss=2. If mcs index is >=16, it is for
Nss=3/4, it need to add rate table, so it is not support in current
ath10k.
This patch is to find the row number in rate table of Nss=1 or Nss=2
with the mcs index reported from firmware.
This patch only effect the chips which supports_peer_stats_info of its
hw_params is true, it is true only for QCA6174 currently.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00048
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597392294-13124-1-git-send-email-wgong@codeaurora.org
When using QCA6174 PCI devices working in station mode, after connected
to AP, tx bitrate is always '1.0 MBit/s' in output of command 'iw wlan0
station dump'. (QCA6174 SDIO devices are working fine.)
After this patch, it show correct bitrate:
Station c4:04:15:5d:97:22 (on wls1)
inactive time: 312 ms
rx bytes: 31496
rx packets: 173
tx bytes: 8625
tx packets: 46
tx retries: 0
tx failed: 0
signal: -76 [-88, -80] dBm
signal avg: -75 [-82, -77] dBm
tx bitrate: 39.0 MBit/s MCS 4
rx bitrate: 26.0 MBit/s MCS 3
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597312029-32348-4-git-send-email-wgong@codeaurora.org
ath10k_sta_statistics is used to report many info to iw wlan0 link,
if it return for empty legacy and nss of arsta->txrate, then the other
stats after it will not be set.
It has 4 bit to set after the return:
NL80211_STA_INFO_TX_FAILED
NL80211_STA_INFO_RX_BITRATE
NL80211_STA_INFO_TX_BITRATE
NL80211_STA_INFO_TX_RETRIES
This patch not effect the info of above 4 bit for all hardware, reason
as below:
NL80211_STA_INFO_TX_FAILED is only for htt.disable_tx_comp is true, it
is for QCA6174 SDIO.
NL80211_STA_INFO_RX_BITRATE and NL80211_STA_INFO_TX_BITRATE are both
set in ath10k_mac_sta_get_peer_stats_info, it is only enabled for chips
which supports_peer_stats_info is true in hw_params, recently only for
QCA6174 SDIO, NL80211_STA_INFO_TX_BITRATE is set again in function
ath10k_mac_sta_get_peer_stats_info because the value which parsed from
arsta->tx_rate_code and arsta->tx_bitrate_kbps is correct for QCA6174
SDIO and PCIe, and the value arsta->txrate is not correct for QCA6174
SDIO and PCIe, so it need to set again with the correct value.
NL80211_STA_INFO_TX_RETRIES is use value of arsta->tx_retries, it is set
in ath10k_update_per_peer_tx_stats, which accumulate the retry_pkts in
HTT message from firmware, if the chips not support this feature, then
it is always 0 after accumulate, then iw wlan0 station dump always show
0 for retry count. If not set NL80211_STA_INFO_TX_RETRIES here, then it
is still 0, so the result is same, then set NL80211_STA_INFO_TX_RETRIES
has no effect.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00048
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597312029-32348-3-git-send-email-wgong@codeaurora.org
ath10k_sta_statistics is used to report info for iw wlan0 link,
it check ath10k_peer_stats_enabled, and ath10k_peer_stats_enabled
check WMI_SERVICE_PEER_STATS bit of ar->wmi.svc_map. SVCMAP() for
WMI_SERVICE_PEER_STATS was defined only for wmi_10x_svc_map and
wmi_10_4_svc_map interfaces, it missed in wmi_tlv_svc_map, so it is
not usable for iw wlan0 link for wmi tlv interface.
If firmware report WMI_TLV_SERVICE_PEER_STATS_INFO for wmi tlv, then
enable the WMI_SERVICE_PEER_STATS bit in ath10k, and then it pass check
in ath10k_peer_stats_enabled and ath10k_sta_statistics pass check.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00048
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597312029-32348-2-git-send-email-wgong@codeaurora.org
When simulate random transfer fail for sdio write and read, it happened
"payload length exceeds max htc length" and recovery later sometimes.
Test steps:
1. Add config and update kernel:
CONFIG_FAIL_MMC_REQUEST=y
CONFIG_FAULT_INJECTION=y
CONFIG_FAULT_INJECTION_DEBUG_FS=y
2. Run simulate fail:
cd /sys/kernel/debug/mmc1/fail_mmc_request
echo 10 > probability
echo 10 > times # repeat until hitting issues
3. It happened payload length exceeds max htc length.
[ 199.935506] ath10k_sdio mmc1:0001:1: payload length 57005 exceeds max htc length: 4088
....
[ 264.990191] ath10k_sdio mmc1:0001:1: payload length 57005 exceeds max htc length: 4088
4. after some time, such as 60 seconds, it start recovery which triggered
by wmi command timeout for periodic scan.
[ 269.229232] ieee80211 phy0: Hardware restart was requested
[ 269.734693] ath10k_sdio mmc1:0001:1: device successfully recovered
The simulate fail of sdio is not a real sdio transter fail, it only
set an error status in mmc_should_fail_request after the transfer end,
actually the transfer is success, then sdio_io_rw_ext_helper will
return error status and stop transfer the left data. For example,
the really RX len is 286 bytes, then it will split to 2 blocks in
sdio_io_rw_ext_helper, one is 256 bytes, left is 30 bytes, if the
first 256 bytes get an error status by mmc_should_fail_request,then
the left 30 bytes will not read in this RX operation. Then when the
next RX arrive, the left 30 bytes will be considered as the header
of the read, the top 4 bytes of the 30 bytes will be considered as
lookaheads, but actually the 4 bytes is not the lookaheads, so the len
from this lookaheads is not correct, it exceeds max htc length 4088
sometimes. When happened exceeds, the buffer chain is not matched between
firmware and ath10k, then it need to start recovery ASAP. Recently then
recovery will be started by wmi command timeout, but it will be long time
later, for example, it is 60+ seconds later from the periodic scan, if
it does not have periodic scan, it will be longer.
Start recovery when it happened "payload length exceeds max htc length"
will be reasonable.
This patch only effect sdio chips.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200108031957.22308-3-wgong@codeaurora.org
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200719104041.57916-1-grandmaster@al2klimov.de
list_for_each_entry{_safe} is able to handle an empty list.
The only effect of avoiding the loop is not initializing the
index variable.
Drop list_empty tests in cases where these variables are not
used.
Note that list_for_each_entry{_safe} is defined in terms of
list_first_entry, which indicates that it should not be used on an
empty list. But in list_for_each_entry{_safe}, the element obtained
by list_first_entry is not really accessed, only the address of its
list_head field is compared to the address of the list head, so the
list_first_entry is safe.
The semantic patch that makes this change for the list_for_each_entry
case is as follows: (http://coccinelle.lip6.fr/)
<smpl>
@@
expression x,e;
statement S;
identifier i;
@@
-if (!(list_empty(x)))
list_for_each_entry(i,x,...) S
... when != i
? i = e
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595761112-11003-8-git-send-email-Julia.Lawall@inria.fr
Instead of using the firmware generated sequence number, use the one
already allocated by the mac80211 layer. This allows better control
of the sequence numbers and avoid to rely on same sequence for Data,
QOS Data and QOS Null Data packets.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-7-git-send-email-loic.poulain@linaro.org
This patch contains the following fixes:
- Use correct queue for submitting QoS packet. The queue id to use
is a one-to-one mapping with the TID.
- Don't encrypt a frame with IEEE80211_TX_INTFL_DONT_ENCRYPT flag.
- Use the 'special queue' for null packets, preventing the firmware
to submit it as AMPDU.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-5-git-send-email-loic.poulain@linaro.org
Increase the short/long retry limit to 15 in order to impove TX
robustness in noisy/busy environment. 15 is the default value
defined in the downstream driver. Observed number of ack timeout
is reduced with this change.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-4-git-send-email-loic.poulain@linaro.org
The controller is capable of reporting TX indication which can be used
to report TX ack when IEEE80211_TX_CTL_REQ_TX_STATUS is set.
The support was only partially implemented.
The firmware can be configured for reporting event when a packet is
acked, without specifying which packet though. In order to send a
packet flagged with TX status callback, we need to stop the queue,
submit the packet and wait for the firmware ack event. Then the queue
can be restarted and mac80211 status callback called.
In case the packet is not acked, no ack event will be received,
therefore a timeout mechanism is introduced to restart the queue
and call the status cb in case no event is received after a 100ms.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-3-git-send-email-loic.poulain@linaro.org
Carl Huang