Mali-DP650 supports warming up the SMMU translations, by sending
requsts to the SMMU before a buffer is read.
There are two modes supported:
- PARTIAL: could be enabled when the buffer is composed of 4K or 64K
pages, the display hardware will send a configurable number of
requests before the actual reading.
- FULL: could be enabled when the buffer is composed of 1M or 2M
pages, the display hardware will send requests before reading for
all pages composing the buffer.
This patch adds a mechanism for detecting the page size and set the
MMU prefetch mode if possible.
Changes since v1:
- For imported buffers use the already populated
drm_gem_cma_object.sgt instead of calling
driver.gem_prime_get_sg_table, which works just for buffers
allocated through the gem_cma API.
Signed-off-by: Jamie Fox <jamie.fox@arm.com>
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
[rebased and re-ordered functions]
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Status register contains a lot of bits for reporting internal errors
inside Mali DP. Currently, we just silently ignore all of the errors,
that doesn't help when we are investigating different bugs, especially
on the FPGA models which have a lot of constraints, so we could easily
end up in AXI or underrun errors.
Add a new file called debug that contains an aggregate of the
errors reported by the Mali DP hardware.
E.g:
[root@alarm ~]# cat /sys/kernel/debug/dri/1/debug
[DE] num_errors : 167
[DE] last_error_status : 0x00000001
[DE] last_error_vblank : 385
[SE] num_errors : 3
[SE] last_error_status : 0x00e23001
[SE] last_error_vblank : 201
Changes since v2:
- Add lock to protect the errors stats.
- Add possibility to reset the error stats by writing anything to the
debug file.
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali-DP has a memory writeback engine which can be used to write the
composition result to a memory buffer. Expose this functionality as a
DRM writeback connector on supported hardware.
Changes since v1:
Daniel Vetter:
- Don't require a modeset when writeback routing changes
- Make writeback connector always disconnected
Changes since v2:
- Rebase onto new drm_writeback_connector
- Add reset callback, allocating subclassed state
Daniel Vetter:
- Squash out-fence support into this commit
Gustavo Padovan:
- Don't signal fence directly from driver (and drop malidp_mw_job)
Changes since v3:
- Modifications to fit with Mali-DP commit tail changes
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
[rebased and fixed conflicts]
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali DP500 behaves differently from the rest of the Mali DP IP,
in that it does not have a one-shot mode and keeps writing the
content of the current frame to the provided memory area until
stopped. As a way of emulating the one-shot behaviour, we are
going to use the CVAL interrupt that is being raised at the
start of each frame, during prefetch phase, to act as End-of-Write
signal, but with a twist: we are going to disable the memory
write engine right after we're notified that it has been enabled,
using the knowledge that the bit controlling the enabling will
only be acted upon on the next vblank/prefetch.
CVAL interrupt will fire durint the next prefetch phase every time
the global CVAL bit gets set, so we need a state byte to track
the memory write enabling. We also need to pay attention during the
disabling of the memory write engine as that requires the CVAL bit
to be set in the control register, but we don't want to do that
during an atomic commit, as it will write into the hardware a partial
state.
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
The top-level error handler calls drm_mode_config_cleanup() which will
destroy all planes. There's no need to destroy them manually in lower
error handlers.
As plane cleanup is now handled entirely by drm_mode_config_cleanup(),
we must ensure that the plane .destroy() handler frees allocated memory
for the plane object that was freed by malidp_de_planes_destroy(). Do so
by replacing the call to devm_kfree() in the .destroy() handler by
kfree(). devm_kfree() is currently a no-op as the plane memory is
allocated with kzalloc(), not devm_kzalloc().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali DP hardware has a 'go' bit (config_valid) for making the new scene
parameters active at the next page flip. The problem with the current
code is that the driver first sets this bit and then proceeds to wait
for confirmation from the hardware that the configuration has been
updated before arming the vblank event. As config_valid is actually
asserted by the hardware after the vblank event, during the prefetch
phase, when we get to arming the vblank event we are going to send it
at the next vblank, in effect halving the vblank rate from the userspace
perspective.
Fix it by sending the userspace event from the IRQ handler, when we
handle the config_valid interrupt, which syncs with the time when the
hardware is active with the new parameters.
Reported-by: Alexandru-Cosmin Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Use drm_fb_cma_fbdev_init() and drm_fb_cma_fbdev_fini() which relies on
the fact that drm_device holds a pointer to the drm_fb_helper structure.
This means that the driver doesn't have to keep track of that.
Also use the drm_fb_helper functions directly.
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171115142001.45358-20-noralf@tronnes.org
Add DRM_MODE_ROTATE_ and DRM_MODE_REFLECT_ defines to the UAPI
as a convenience.
Ideally the DRM_ROTATE_ and DRM_REFLECT_ property ids are looked up
through the atomic API, but realizing that userspace is likely to take
shortcuts and assume that the enum values are what is sent over the
wire.
As a result these defines are provided purely as a convenience to
userspace applications.
Changes since v3:
- Switched away from past tense in comments
- Add define name change to previously mis-spelled DRM_REFLECT_X comment
- Improved the comment for the DRM_MODE_REFLECT_<axis> comment
Changes since v2:
- Changed define prefix from DRM_MODE_PROP_ to DRM_MODE_
- Fix compilation errors
- Changed comment formatting
- Deduplicated comment lines
- Clarified DRM_MODE_PROP_REFLECT_ comment
Changes since v1:
- Moved defines from drm.h to drm_mode.h
- Changed define prefix from DRM_ to DRM_MODE_PROP_
- Updated uses of the defines to the new prefix
- Removed include from drm_rect.c
- Stopped using the BIT() macro
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170519205017.23307-2-robert.foss@collabora.com
Enable the scaling engine for upscaling a single plane using the polyphase
scaler. No image enhancement support or downscaling yet*, and composition
result scaling is not implemented.
* Downscaling a plane requires mclk > pxlclk.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Add a core_id file in the driver's sysfs directory,
exposing the hardware CORE ID. This is useful to allow
userspace to discover the hardware version used.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
All DPs have a COLORADJ matrix which is applied prior to output gamma.
Attach that to the CTM property. Also, ensure the input CTM's coefficients
can fit in the DP registers' Q3.12 format.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Add gamma via the DRM GAMMA_LUT/GAMMA_LUT_SIZE CRTC
properties. The expected LUT size is 4096 in order
to produce as accurate a set of segments as possible.
This version uses only the green channel's gamma curve
to set the hardware curve on DP550/650. For the sake of
simplicity, it uses the same table of coefficients for
all 3 curves on DP500.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Add a custom CRTC state struct to enable storing driver's private
state. This patch only adds the base drm_crtc_state struct and
the atomic functions that handle it.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Enable runtime and system Power Management. Clocks are now managed
from malidp_crtc_{enable,disable} functions. Suspend-to-RAM tested
as working on Juno.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Save a search through the format lists at commit-time by storing the
internal format ID and number of planes in our plane state.
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Add support for the new family of Display Processors from ARM Ltd.
This commit adds basic support for Mali DP500, DP550 and DP650
parts, with only the display engine being supported at the moment.
Cc: David Brown <David.Brown@arm.com>
Cc: Brian Starkey <Brian.Starkey@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jamie Fox