The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mmc/host/sdhci-sprd.c:723:34: warning:
‘sdhci_sprd_of_match’ defined but not used [-Wunused-const-variable=]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Link: https://lore.kernel.org/r/20201120162344.485921-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers. This batch converts
the drivers that appeared to be around in the v5.4 timeframe.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200903162412.5.I2b630c4d40ff4ea61d5b30b8ccfe95890e257100@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement the request_atomic() API for nonremovable cards, that means
we can submit next request in the irq hard handler context to reduce
latency.
Moreover factor out the AUTO CMD23 checking into a separate function
to reduce duplicate code.
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/60142fe6c6c1dbba2696e775564ae2166786f0bc.1586744073.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Patch all drivers which use mmc_regulator_set_vqmmc() and prepare them for
the fact that mmc_regulator_set_vqmmc() can return a value > 0, which would
happen if the signal voltage switch did NOT happen, because the voltage was
already set correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20200416163649.336967-1-marex@denx.de
[Ulf: Re-worked/simplified the code a bit]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC_CAP_ERASE and MMC_CAP_CMD23 flags are already being set in the
common sdhci_setup_host(). This makes it redundant to set them for
sdhci-sprd, so let's drop them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200406113724.8504-1-ulf.hansson@linaro.org
The Spreadtrum host controller supports HW busy detection for commands with
R1B responses, but also for I/O operations. This means when the host gets a
transfer complete event, that always indicates the busy signal is released.
Let's inform the mmc core about this, via setting the corresponding
MMC_CAP_WAIT_WHILE_BUSY flag, as to remove some redundant software busy
polling.
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/96f16647f6a6e8cb058c44e46c61b122df027059.1582535202.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The register SDHCI_CLOCK_CONTROL should be cleared before config clock
divider, otherwise the frequency configured maybe lower than we
expected.
Fixes: fb8bd90f83 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Chunyan Zhang <zhang.lyra@gmail.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SD host controller specification defines 3 types software reset:
software reset for data line, software reset for command line and software
reset for all. Software reset for all means this reset affects the entire
Host controller except for the card detection circuit.
In sdhci_runtime_resume_host() we always do a software "reset for all",
which causes the Spreadtrum variant controller to work abnormally after
resuming. To fix the problem, let's do a software reset for the data and
the command part, rather than "for all".
However, as sdhci_runtime_resume() is a common sdhci function and we don't
want to change the behaviour for other variants, let's introduce a new
in-parameter for it. This enables the caller to decide if a "reset for all"
shall be done or not.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Fixes: fb8bd90f83 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the SD host controller tries to probe again due to the derferred
probe mechanism, it will always keep the SD host device as runtime
resume state due to missing the runtime put operation in error path
last time.
Thus add the pm_runtime_put_noidle() in error path to make the PM runtime
counter balance, which can make the SD host device's PM runtime work well.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: fb8bd90f83 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For Spreadtrum SD card voltage switching, besides regulator setting,
it also need switch related pin's state to output corresponding voltage.
This patch adds pin control operation to support voltage switch.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For Spreadtrum SD host controller, we can not use standard SD registers
to change and detect the I/O voltage signals, since our voltage regulator
for I/O is fixed in hardware, and no signals were connected to the SD
controller. Thus add Spreadtrum specific voltage switch ops to change
voltage instead of using standard SD host registers.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set the PHY DLL delay for each timing mode, which is used to sample the clock
accurately and make the clock more stable.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For the Spreadtrum SD host controller, when we changed the clock to be
more than 52M, we should enable the PHY DLL which is used to track the
clock frequency to make the clock work more stable. Otherwise deviation
may occur of the higher clock.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement the get_max_timeout_count() interface to set the Spredtrum SD
host controller actual maximum timeout count.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For the Spreadtrum SC9860 platform, we should enable another gate clock
'2x_enable' to make the SD host controller work well.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Missed to check the enable clock's return value, fix it.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds the initial support of Secure Digital Host Controller
Interface compliant controller found in some latest Spreadtrum chipsets.
This patch has been tested on the version of SPRD-R11 controller.
R11 is a variant based on SD v4.0 specification.
With this driver, R11 mmc can be initialized, can be mounted, read and
written.
Original-by: Billows Wu <billows.wu@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Krzysztof Kozlowski