The core implementation of cs_change didn't follow the documentation
which says that cs_change in the middle of the transfer means to briefly
deassert chip select, instead it followed buggy drivers which change the
polarity of chip select. Use a delay of 10us between deassert and
reassert simply from pulling numbers out of a hat.
Reported-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This controller only supports 8-bit word length.
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Also remove the duplicate code to test spi->mode, it is done by spi core.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The memory allocated for cs is not freed anywhere.
Convert to use devm_kzalloc to fix the memory leak.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
With devm_kzalloc, the memory is automatically freed when spi_device detach from
the bus.
Fixes: commit 43f627ac9d (spi: dw: fix memory leak on error path)
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stabe@vger.kernel.org
The memory allocated for chip is not freed anywhere.
Convert to use devm_kzalloc to fix the memory leak.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This fixes the following coccicheck warning:
linux-2.6/drivers/spi/spi-omap-uwire.c:485:2-8: ERROR: missing iounmap; ioremap on line 471 and execution via conditional on line 481
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set highest transfer speed to master->max_speed_hz and then we can remove
hw->max_speed.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch merges support for all DB1xxx and PB1xxx
boards into a single image, along with a new single defconfig
for them.
Run-tested on DB1300 and DB1500.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6577/
Patchwork: https://patchwork.linux-mips.org/patch/6659/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This driver sets the SPI_MASTER_HALF_DUPLEX flag, so the spi core will check
transfers to ensure they are not full duplex.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no real reason why we require transfers to have a completion and
the only user of the completion now checks to see if one has been provided
before using it so stop enforcing this. This makes it more convenient for
drivers to chain multiple asynchronous transfers together.
Signed-off-by: Mark Brown <broonie@linaro.org>
If during a SPI transfer with len larger than PCH_MAX_FIFO_DEPTH and the
IRQ handler happens to be called when the transmit FIFO is already empty,
and SPSR_FI_BIT is set consequently, the message
"spi_master spi32766: pch_spi_handler_sub : Transfer is not completed"
is spammed to the systemlog, because tx_index has already increased
further due to the next bytes to be written. This case is uncritical as
new bytes have already been written.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi core will use spi->max_speed_hz as transfer speed if the transfer speed was
not set. So we don't need to test t->speed_hz in mcfqspi_transfer_one().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Wolfram Sang pointed out that "efm32,$device" is non-standard. So use the
common scheme and prefix device with "efm32-". The old compatible string
is left in place until arch/arm/boot/dts/efm32* is fixed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
This patch removes <mach/hardware.h> dependency. This is performed
by replace hard coded used memory regions and interrupt to getting
these values from resources passed to the driver. For the system-wide
registers we now able to use SYSCON driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
Ensure all registered platform devices are unregistered on probe() error paths.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The definition of struct altera_spi_platform_data does not exist in current
tree. So remove the code to get platform_data which is never used.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_mpc8xxx_spi_probe() allocates memory for pinfo but the memory is not freed
anywhere. of_mpc8xxx_spi_probe() is called in .probe() and pinfo should be
freed in .remove(), so convert kzalloc to devm_kzalloc to fix the memory leak.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This helps increasing build testing coverage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The correct way to set multiple bits settings is always clear these
bit fields before set new settings.
Current code does not cause problem because the reset value of these
bit fields are 0, and these settings only set once during probe.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix printk format warning by using %p extension 'ad' for dma_addr_t.
drivers/spi/spi-atmel.c:1228:3: warning: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t' [-Wformat]
drivers/spi/spi-atmel.c:1228:3: warning: format '%x' expects argument of type 'unsigned int', but argument 9 has type 'dma_addr_t' [-Wformat]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The tnetv107x platform is getting removed, so this driver
will not be needed any more.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
When xfer->speed_hz is greater than master->max_speed_hz, it's generally safe
to use master->max_speed_hz as transfer speed.
Thus use master->max_speed_hz as transfer speed rather than return error when
xfer->speed_hz > master->max_speed_hz.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
While reviewing an i2c driver for efm32 that needs a similar property
Wolfram Sang pointed out that "location" is a too generic name for
something that is efm32 specific. So add an appropriate namespace and
fall back to the generic name in case of failure.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
If sp->info is NULL, we will hit NULL pointer dereference in probe() while
setting bus_num and num_chipselect for master:
sp->bitbang.master->bus_num = sp->info->bus_num;
sp->bitbang.master->num_chipselect = sp->info->num_chipselect;
Thus add NULL test for sp->info in probe() to prevent NULL pointer dereference.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is required since commit 2025172e32 "spi/bitbang: Use core message pump".
spi-bitbang now uses core message pump, so it needs to call spi_master_suspend/
spi_master_resume to stop/start the queue while suspend/resume.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver does not work for bits_per_word greater than 16.
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We already has NULL test for master after calling spi_alloc_master().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the implementation of __spi_validate(), spi core will set transfer
bits_per_word and max speed as spi device default if it is not set for
this transfer. So we can remove the same logic in spi_clps711x_setup_xfer() and
spi_clps711x_transfer_one().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set master->max_speed_hz and master->min_speed_hz then spi core will handle
checking transfer speed. So we can remove the same checking in this driver.
This patch also remove testing if hz is 0 because spi->max_speed_hz will be
default set to master->min_speed_hz if it was not set. So the transfer speed
will never set to 0.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This simple SPI master controller is built into xtfpga bitstreams. It
always transfers 16 bit words in SPI mode 0, automatically asserting CS
on transfer start and deasserting on end.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is a DT-only driver, so remove all non-DT paths.
of_gpio_named_count() may fail, thus also add checking it's return value.
efm32_spi_probe_dt() never fails, make it return void.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
If pdata->cs_control is NULL, we will hit NULL pointer dereference in
mcfqspi_cs_select() and mcfqspi_cs_deselect(). Thus add NULL test for
pdata->cs_control in probe().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The label argument was removed by commit 989847967c
spi: clps711x: Use devm_gpio_request(), add it back.
This makes it easier to know the gpio usage in /sys/kernel/debug/gpio.
Also remove unnecessary gpio_is_valid() checking, devm_gpio_request() returns
error if the requested gpio is invalid.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This ensures clock has been enabled before calling spi_master_resume().
while at it, also add checking return value of spi_master_suspend and
spi_master_resume because they may fail.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
mmap resource requirement is only for memory mapped operations.
If the user does not populate mmap resource, dont call return,
instead we go on for normal spi mode operations.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is required since commit 2025172e32 "spi/bitbang: Use core message pump".
spi-bitbang now uses core message pump, so it needs to call spi_master_suspend/
spi_master_resume to start/stop the queue while suspend/resume.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Previously only the resources controlled by the driver were put into
low power state at system suspend. Both the amba bus and a potential
power domain were ignored.
Moreover, while putting the device into low power state we first
brought it back to full power, but for no particular reason.
To handle both issues above, use pm_runtime_force_suspend|resume() from
the system suspend|resume callbacks.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Convert to the SET_PM_RUNTIME_PM macro while defining the runtime PM
callbacks. This means the callbacks becomes available for both
CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME, which is needed to handle the
combinations of these scenarios.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use SIMPLE_DEV_PM_OPS macro in order to make the code simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use SIMPLE_DEV_PM_OPS macro in order to make the code simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the following checkpatch issues.
ERROR: space prohibited after that open parenthesis '('
ERROR: space required before the open parenthesis '('
ERROR: trailing statements should be on next line
ERROR: space required after that ',' (ctx:VxV)
ERROR: spaces required around that '-=' (ctx:VxV)
WARNING: sizeof *cs should be sizeof(*cs)
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The PM callbacks implemented by the spi-atmel driver don't call
spi_master_{resume,suspend}, fix that.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Convert to use default implementation of transfer_one_message().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
dev_get_drvdata() returns the address of master rather than mcfqspi.
Fixes: af361079 (spi/coldfire-qspi: Drop extra calls to spi_master_get in suspend/resume functions)
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Current code set platform drvdata to dspi. However, the code in dspi_suspend()
and dspi_resume() assumes the drvdata is the address of master.
Fix it by setting platform drvdata to master.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Amend the spi atmel pin controller to optionally take a pin control
handle and set the state of the pins to:
- "default" on boot, resume and before performing an spitransfer
- "sleep" on suspend()
This should make it possible to optimize energy usage for the pins
both for the suspend/resume cycle
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Zero length transfer becomes invalid since
"spi: core: Validate length of the transfers in message" commit,
but it should be valid to support an odd device, for example, which
requires long delay between chipselect and the first transfer, etc.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the implementation of __spi_validate(), spi core will set transfer
bits_per_word and max speed as spi device default if it is not set for
this transfer. So we can remove the same logic in spi_xcomm_setup_transfer().
Also remove a redundant code to initialize is_first variable.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This controller only supports 8 bits word length.
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This controller only supports 8 bits word length.
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The 'ath79_spi_setup_cs' function initializes the chip
select line of a given SPI device in order to make sure
that the device is inactive.
If the SPI_CS_HIGH bit is set for a given device, it
means that the CS line of that device is active HIGH
so it must be set to LOW initially. In case of GPIO
CS lines, the 'ath79_spi_setup_cs' function does the
opposite of that due to the wrong GPIO flags.
Fix the code to use the correct GPIO flags.
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Set master->max_speed_hz then spi core will handle checking transfer speed.
So we can remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi core will handle validating transfer length since commit 4d94bd21b3
"spi: core: Validate length of the transfers in message".
So remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set master->max_speed_hz then spi core will handle checking transfer speed.
The behavior is different from current code when the speed_hz is greater than
the maximum transfer speed supported by the controller.
Unless there is other good reason, I think we had better make the behavior
consistent with what spi core does.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code uses struct octeon_spi_setup to store max_speed_hz, chip_select and
mode settings of current spi device.
We can always get the same settings in octeon_spi_do_transfer() by msg->spi.
So this patch removes struct octeon_spi_setup and octeon_spi_setup,
octeon_spi_cleanup functions.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
there are many SPI clients which use the following protocal:
step 1: send command bytes to clients(rx buffer is empty)
step 2: send data bytes to clients or receive data bytes from
clients.
SiRFprimaII provides a shortcut for this kind of SPI transfer.
when tx buf is less or equal than 4 bytes and rx buf is null
in a transfer, we think it as 'command' data and use hardware
command register for the transfer.
here we can save some CPU loading than doing both tx and rx
for a normal transfer.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the implementation of __spi_validate(), spi core will set transfer
bits_per_word and max speed as spi device default if it is not set for
this transfer. So we can remove the same implementation in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the implementation of __spi_validate(), spi core will use spi device's max
speed as default transfer speed if it is not set for this transfer.
So we can remove the same logic in hspi_hw_setup().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi core will handle validating transfer length since commit 4d94bd21b3
"spi: core: Validate length of the transfers in message".
So remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi core will handle validating transfer length since commit 4d94bd21b3
"spi: core: Validate length of the transfers in message".
So remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_ioremap_resource() in order to make the code simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently, at module removal, one gets the following warnings:
------------[ cut here ]------------
WARNING: at drivers/clk/clk.c:780 clk_disable+0x18/0x24()
Modules linked in: spi_imx(-) [last unloaded: ev76c560]
CPU: 1 PID: 16337 Comm: rmmod Tainted: G W 3.10.17-80548-g90191eb-dirty #33
[<80013b4c>] (unwind_backtrace+0x0/0xf8) from [<800115dc>] (show_stack+0x10/0x14)
[<800115dc>] (show_stack+0x10/0x14) from [<800257b8>] (warn_slowpath_common+0x4c/0x68)
[<800257b8>] (warn_slowpath_common+0x4c/0x68) from [<800257f0>] (warn_slowpath_null+0x1c/0x24)
[<800257f0>] (warn_slowpath_null+0x1c/0x24) from [<803f60ec>] (clk_disable+0x18/0x24)
[<803f60ec>] (clk_disable+0x18/0x24) from [<7f02c9cc>] (spi_imx_remove+0x54/0x9c [spi_imx])
[<7f02c9cc>] (spi_imx_remove+0x54/0x9c [spi_imx]) from [<8025868c>] (platform_drv_remove+0x18/0x1c)
[<8025868c>] (platform_drv_remove+0x18/0x1c) from [<80256f60>] (__device_release_driver+0x70/0xcc)
[<80256f60>] (__device_release_driver+0x70/0xcc) from [<80257770>] (driver_detach+0xcc/0xd0)
[<80257770>] (driver_detach+0xcc/0xd0) from [<80256d90>] (bus_remove_driver+0x7c/0xc0)
[<80256d90>] (bus_remove_driver+0x7c/0xc0) from [<80068668>] (SyS_delete_module+0x144/0x1f8)
[<80068668>] (SyS_delete_module+0x144/0x1f8) from [<8000e080>] (ret_fast_syscall+0x0/0x30)
---[ end trace 1f5df9ad54996300 ]---
------------[ cut here ]------------
WARNING: at drivers/clk/clk.c:780 clk_disable+0x18/0x24()
Modules linked in: spi_imx(-) [last unloaded: ev76c560]
CPU: 1 PID: 16337 Comm: rmmod Tainted: G W 3.10.17-80548-g90191eb-dirty #33
[<80013b4c>] (unwind_backtrace+0x0/0xf8) from [<800115dc>] (show_stack+0x10/0x14)
[<800115dc>] (show_stack+0x10/0x14) from [<800257b8>] (warn_slowpath_common+0x4c/0x68)
[<800257b8>] (warn_slowpath_common+0x4c/0x68) from [<800257f0>] (warn_slowpath_null+0x1c/0x24)
[<800257f0>] (warn_slowpath_null+0x1c/0x24) from [<803f60ec>] (clk_disable+0x18/0x24)
[<803f60ec>] (clk_disable+0x18/0x24) from [<7f02c9e8>] (spi_imx_remove+0x70/0x9c [spi_imx])
[<7f02c9e8>] (spi_imx_remove+0x70/0x9c [spi_imx]) from [<8025868c>] (platform_drv_remove+0x18/0x1c)
[<8025868c>] (platform_drv_remove+0x18/0x1c) from [<80256f60>] (__device_release_driver+0x70/0xcc)
[<80256f60>] (__device_release_driver+0x70/0xcc) from [<80257770>] (driver_detach+0xcc/0xd0)
[<80257770>] (driver_detach+0xcc/0xd0) from [<80256d90>] (bus_remove_driver+0x7c/0xc0)
[<80256d90>] (bus_remove_driver+0x7c/0xc0) from [<80068668>] (SyS_delete_module+0x144/0x1f8)
[<80068668>] (SyS_delete_module+0x144/0x1f8) from [<8000e080>] (ret_fast_syscall+0x0/0x30)
---[ end trace 1f5df9ad54996301 ]---
Since commit 9e556dcc55, "spi: spi-imx: only
enable the clocks when we start to transfer a message", clocks are always
disabled except when transmitting messages. There is thus no need to
disable them at module removal.
Fixes: 9e556dcc55 (spi: spi-imx: only enable the clocks when we start to transfer a message)
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
hspi_cleanup() is doing nothing except print a non-useful debug message,
so remove it. Also remove unused hspi2info macro.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The only remaining feature of spi-bitbang used by this driver is the
chipselect() callback, which just does conditional GPIO.
This is handled fine by the SPI core's spi_set_cs(), hence switch the
driver to use the core message handling through our own transfer_one()
method.
As the (optional) GPIO CS is no longer deasserted at spi_master.setup()
time (through spi_bitbang_setup() and the spi_bitbang.chipselect()
callback), we now have to take care of that ourselves.
Remove the call to spi_master_put() in sh_msiof_spi_remove(), as our SPI
master is now registered using devm_spi_register_master()
(spi_bitbang_start() uses the non-managed version).
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set bits_per_word_mask so the spi core will reject transfers that attempt
to use an unsupported bits_per_word value.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move clock management and pin configuration from the bitbang chipselect()
method to the SPI core prepare_message() and unprepare_message() methods.
As spi_master.{,un}prepare_message() is guaranteed to be called in
matching pairs, the clock management synchronization is no longer needed.
As sh_msiof_spi_set_pin_regs() is no longer called at spi_master.setup()
time (through spi_bitbang_setup() and the spi_bitbang.chipselect()
callback), we now have to take care of that ourselves.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for the MSIOF variant in the R-Car H2 (r8a7790) and M2
(r8a7791) SoCs.
Binding documentation:
- Add future-proof "renesas,msiof-<soctype>" compatible values,
- The default for "renesas,rx-fifo-size" is 256 on R-Car H2 and M2,
- "renesas,tx-fifo-size" and "renesas,rx-fifo-size" are deprecated for
soctype-specific bindings,
- Add example bindings.
Implementation:
- MSIOF on R-Car H2 and M2 requires the transmission of dummy data if
data is being received only (cfr. "Set SICTR.TSCKE to 1" and "Write
dummy transmission data to SITFDR" in paragraph "Transmit and Receive
Procedures" of the Hardware User's Manual).
- As RX depends on TX, MSIOF on R-Car H2 and M2 also lacks the RSCR
register (Receive Clock Select Register), and some bits in the RMDR1
(Receive Mode Register 1) and TMDR2 (Transmit Mode Register 2)
registers.
- Use the recently introduced SPI_MASTER_MUST_TX flag to enable support
for dummy transmission in the SPI core, and to differentiate from other
MSIOF implementations in code paths that need this.
- New DT compatible values ("renesas,msiof-r8a7790" and
"renesas,msiof-r8a7791") are added, as well as new platform device
names ("spi_r8a7790_msiof" and "spi_r8a7791_msiof").
- The default RX FIFO size is 256 words on R-Car H2 and M2.
This is loosely based on a set of patches from Takashi Yoshii
<takasi-y@ops.dti.ne.jp>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
As different variants of MSIOF have different FIFO sizes, move the default
FIFO sizes to a new struct sh_msiof_chipdata, pointed to from the device
ID data.
[Moved ifdef to fix build -- broonie]
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
Documentation:
- Add missing "interrupt-parent", "#address-cells", "#size-cells", and
"clocks" properties,
- Add missing default values for "num-cs", "renesas,tx-fifo-size" and
"renesas,rx-fifo-size",
- Add a reference to the pinctrl documentation.
Implementation:
- As "num-cs" is marked optional, provide a sensible default.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for Dual/Quad SPI Transfers to the spidev API.
As this uses SPI mode bits that don't fit in a single byte, two new
ioctls (SPI_IOC_RD_MODE32 and SPI_IOC_WR_MODE32) are introduced.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
In commit f477b7fb13 ("spi: DUAL and QUAD
support"), spi_device.mode was enlarged from 8 to 16 bits.
However, the spidev code still only saved 8 bits of data. If a spidev
SPI_IOC_WR_MODE or SPI_IOC_WR_LSB_FIRST request failed, only the lower 8
bits of the SPI mode were restored, inadvertently clearing the upper 8
bits, possibly disabling Quad or Dual SPI transfers for the device.
Save up to 32 bits to fix this.
For SPI_IOC_WR_MODE this is probably not so important, as it doesn't allow
setting Quad or Dual mode anyway, but SPI_IOC_WR_LSB_FIRST is used to just
set or clear a single bit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use SIMPLE_DEV_PM_OPS macro in order to make the code simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove unnecessary space in order to fix the following
checkpatch issues.
WARNING: Unnecessary space after function pointer name
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Mark Brown <broonie@linaro.org>
If during registering SPI master due to SPI device probing a SPI transfer
is issued the DMA buffers are not allocated yet.
This fixes the following oops:
pch_spi 0000:02:0c.1: enabling device (0000 -> 0002)
pch_spi 0000:02:0c.1: master is unqueued, this is deprecated
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<c125aa05>] pch_spi_handle_dma+0x15c/0x6f4
[...]
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code uses struct spi_qup_device to store spi->mode and spi->chip_select
settings. We can get these settings in spi_qup_transfer_one and spi_qup_set_cs
without using struct spi_qup_device. Refactor the code a bit to remove
spi_qup_setup(), spi_qup_cleanup(), and struct spi_qup_device.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi core will handle validating transfer length since commit 4d94bd21b3
"spi: core: Validate length of the transfers in message".
So remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The module version is unlikely to be updated, use kernel version should be
enough.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver uses writel_relaxed() which does not exist in x86, ppc, etc.
Make it depend on ARM && COMPILE_TEST to avoid below build error:
CC [M] drivers/spi/spi-qup.o
drivers/spi/spi-qup.c: In function 'spi_qup_set_state':
drivers/spi/spi-qup.c:180:3: error: implicit declaration of function 'writel_relaxed' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[2]: *** [drivers/spi/spi-qup.o] Error 1
make[1]: *** [drivers/spi] Error 2
make: *** [drivers] Error 2
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
use SET_SYSTEM_SLEEP_PM_OPS to initialize PM entries, this makes the codes
clean and also enable the ability of hibernation support for sirf SPI.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
sirf-dma driver enabled generic dt binding for dma channels.
see here we remove self-defined dma channel prop and move to
use generic dma_request_slave_channel.
related changes in dts is something like:
dmas = <&dmac1 9>,
<&dmac1 4>;
dma-names = "rx", "tx";
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix below build error when CONFIG_PM_RUNTIME=y:
C [M] drivers/spi/spi-qup.o
drivers/spi/spi-qup.c: In function 'spi_qup_pm_suspend_runtime':
drivers/spi/spi-qup.c:712:12: error: 'QUP_CLOCK_AUTO_GATE' undeclared (first use in this function)
drivers/spi/spi-qup.c:712:12: note: each undeclared identifier is reported only once for each function it appears in
drivers/spi/spi-qup.c: In function 'spi_qup_pm_resume_runtime':
drivers/spi/spi-qup.c:725:13: error: 'QUP_CLOCK_AUTO_GATE' undeclared (first use in this function)
make[2]: *** [drivers/spi/spi-qup.o] Error 1
make[1]: *** [drivers/spi] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fixes below checkpatch warning:
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(10);
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
fsl_spi_grlib_probe() may update mpc8xxx_spi->max_bits_per_word setting.
So set master->bits_per_word_mask after fsl_spi_grlib_probe().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
spi_bitbang requires custom setup_transfer() to be defined if there is a
custom txrx_bufs(). Thus keep the empty xilinx_spi_setup_transfer() function
in the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set master->max_speed_hz then spi core will handle checking transfer speed.
So we can remove the same checking in this driver.
Also remove checking spi->chip_select in spi_qup_setup(), the checking is done
by spi core.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver uses devm_spi_register_master() so don't explicitly call
spi_master_put() in spi_qup_remove().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
While normal Dual and Quad SPI Transfers are unidirectional, we must do
a bidirectional transfer if loopback mode is enabled, else rx_buf is not
filled.
With spidev it seemed to work, as spidev uses the same buffer for
tranmission and reception.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
If spi_master.cleanup() is not needed, it can be left unimplemented.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The older Allwinner SoCs (A10, A13, A10s and A20) all have the same SPI
controller.
Unfortunately, this SPI controller, even though quite similar, is significantly
different from the recently supported A31 SPI controller (different registers
offset, split/merged registers, etc.). Supporting both controllers in a single
driver would be unreasonable, hence the addition of a new driver.
Like its more recent counterpart, it supports DMA, but the driver only does PIO
until we have a dmaengine driver for this platform.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SPI_IMX is selected by imx_v6_v7_defconfig/imx_v4_v5_defconfig and we don't need
to have a default setting which depends on the IMX_HAVE_PLATFORM_SPI_IMX symbol.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In current implementation, CS is controlled by GPIO, which is passed
through spi->controller_data. However, the MSIOF HW module has a function
to output CS by itself, which is already enabled and actual switch will be
done by pinmux.
Store the GPIO number in the core cs_gpio field, and ignore it if it is
an invalid (negative) GPIO number.
Loosely based on a patch from Takashi Yoshii <takasi-y@ops.dti.ne.jp>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Both spi_transfer.speed_hz and spi_master.max_speed_hz are u32
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
DT doesn't instantiate SPI children if spi_master.dev.of_node is not set up
properly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
SPI transfer length should be multiple of SPI word size,
where SPI word size should be power-of-two multiple
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Convert to use default implementation of transfer_one_message() which provides
standard handling of delays and chip select management.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
Qualcomm Universal Peripheral (QUP) core is an AHB slave that
provides a common data path (an output FIFO and an input FIFO)
for serial peripheral interface (SPI) mini-core. SPI in master
mode supports up to 50MHz, up to four chip selects, programmable
data path from 4 bits to 32 bits and numerous protocol variants.
Cc: Alok Chauhan <alokc@codeaurora.org>
Cc: Gilad Avidov <gavidov@codeaurora.org>
Cc: Kiran Gunda <kgunda@codeaurora.org>
Cc: Sagar Dharia <sdharia@codeaurora.org>
Cc: dsneddon@codeaurora.org
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
bus_num might be asigned dynamically to e.g. 32766. In this case the
calculated DMA channel based on SPI bus number is bogus. Use SPI channel
number instead for calculation.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set master->max_speed_hz and master->min_speed_hz then spi core will handle
checking transfer speed. So we can remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For DT case, spi core will call of_alias_get_id() and set master->bus_num if it
was not set.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The purpose of commit 1e8a52e18c
"spi: By default setup spi_masters with 1 chipselect and dynamics bus number"
is to avoid setting default value for bus_num and num_chipselect in spi master
drivers. So let's remove the duplicate code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-By: David Daney <david.daney@cavium.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove some coding sytle not in standard in former code.
Signed-off-by: Chao Fu <b44548@freescale.com>
Reviewed-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Freescale DSPI module will have two endianess in different platform,
but ARM is little endian. So when DSPI in big endian, core in little endian,
readl and writel can not adjust R/W register in this condition.
This patch will remove general readl/writel, and import regmap mechanism.
Data endian will be transfered in regmap APIs.
Documents: dspi add bool "big-endian" in dts node if DSPI module
work in big endian.
Signed-off-by: Chao Fu <b44548@freescale.com>
Reviewed-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code in sun6i_spi_set_cs() actually clears CPHA and CPOL bits which is
obvious wrong. The define for SUN6I_TFR_CTL_CS_MASK is wrong. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
No need to return a 'fake' return value on platform_get_irq() failure.
Just return the error code itself instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
No need to return a 'fake' return value on platform_get_irq() failure.
Just return the error code itself instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
By setting master->max_speed_hz and master->min_speed_hz, spi core will handle
checking transfer speed. So we can remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set "master->max_speed_hz = PCH_MAX_BAUDRATE" then we can remove pch_spi_setup.
In additional, pspi->max_speed_hz will never be 0 because it's default value
will be set to master->max_speed_hz.
Also remove list_empty checking in pch_spi_transfer() because the checking is
done by spi core.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
By setting master->max_speed_hz and master->min_speed_hz, spi core will handle
checking transfer speed. So we can remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Mark Brown <broonie@linaro.org>
This checking is already done in the implementation of spi_setup().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
While backporting 33cf00e5 ("spi: attach/detach SPI device to the ACPI
power domain"), I noticed that the code changes were suboptimal:
* Why use &spi->dev when we have dev at hand?
* After fixing the above, spi is used only once, so we don't really
need a local variable for it.
This results in the following clean-up.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In spi_add_device(), we have the code to validate spi->chip_select.
So remove the duplicate code in various drivers.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
So it will be checked when spi device is added onto the spi bus.
spi_add_device() calls spi_setup() which then calls spi->master->setup().
No need to check it every time sc18is602_transfer_one() is called.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use master->max_speed_hz instead of tspi->spi_max_frequency, so spi core will
handle checking transfer speed.
In additional, since commit 052eb2d490 'spi: core: Set max_speed_hz of
spi_device default to max_speed_hz of controller',
spi core will also set default spi->max_speed_hz if it is not set.
So remove the duplicate code in tegra_slink_setup.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use master->max_speed_hz instead of tspi->spi_max_frequency, so spi core will
handle checking transfer speed.
In additional, since commit 052eb2d490 'spi: core: Set max_speed_hz of
spi_device default to max_speed_hz of controller',
spi core will also set default spi->max_speed_hz if it is not set.
So remove tegra_sflash_setup().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use master->max_speed_hz instead of tspi->spi_max_frequency, so spi core will
handle checking transfer speed.
In additional, since commit 052eb2d490 'spi: core: Set max_speed_hz of
spi_device default to max_speed_hz of controller',
spi core will also set default spi->max_speed_hz if it is not set.
So remove the duplicate code in tegra_spi_setup.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
By setting master->max_speed_hz and master->min_speed_hz, spi core will handle
checking transfer speed. Then we can remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Mark Brown <broonie@linaro.org>
In __spi_validate(), xfer->speed_hz is set to be spi->max_speed_hz if it is not
set for this transfer. However, if spi->max_speed_hz is also not set,
xfer->speed_hz is 0. Some drivers (e.g. au1550, tegra114, tegra20-sflash,
tegra20-slink, etc.) then use below code to avoid setting xfer->speed_hz to 0.
/* Set speed to the spi max fequency if spi device has not set */
spi->max_speed_hz = spi->max_speed_hz ? : tspi->spi_max_frequency;
Let's handle it in spi core.
If spi->max_speed_hz is not set, make it default to spi->master->max_speed_hz.
So In __spi_validate() if both xfer->speed_hz and spi->max_speed_hz are not set,
xfer->speed_hz will be set to spi->master->max_speed_hz.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 0079aae0f1 ("spi: omap2: Add build dependencies for
writel_relaxed()") added an optional Kconfig dependency on SH. That
Kconfig symbol doesn't exist. Apparently SUPERH was intended. Use that.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Calling init_completion() once is enough.
For the rest of the iterations, call reinit_completion() instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Mark Brown