The link resume logic uses a 200msec delay while debouncing
the SControl register. The rationale behind that delay is
to accommodate some PHYs that behave badly if their SStatus/
SControl registers are pounded immediately on resume.
The Broadcom STB SATA PHY does not seem to have this issue.
This patch introduces a new link flag that allows platforms
to skip the debounce delay if it isn't needed.
Signed-off-by: Danesh Petigara <dpetigara@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The Broadcom STB SATA host controller does not support device
initiated power management. Disable support for this feature
so the driver never sends SETFEATURES commands to the device
to enable/disable DIPM.
Signed-off-by: Danesh Petigara <dpetigara@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Enable support for ALPM in the host controller's capabilities
register. Also adjust the PLL timeout to give it enough time
to lock when the port exits slumber mode.
tj: minor style updates
Signed-off-by: Danesh Petigara <dpetigara@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The BCM7xxx ARM-based and MIPS-based platforms share a similar hardware
block for AHCI SATA3.
This new compatible string, "brcm,bcm7425-ahci", may be used for most
MIPS-based platforms of 40nm process technology.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Remove unused definitions, and this is to avoid confusion with MIPS-based
platforms.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Whereas ARM-based platforms have four phy interface registers and
information, the MIPS-based platforms have only three registers, and
there are no information and documentation. In the original BSP, It
using "strict-ahci" did not control these registers.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
The most MIPS-based platforms need to disable NCQ while have the NCQ
capability in HOST_CAP, and several ARM-based platforms (eg. BCM7349A0,
BCM7445A0, BCM7445B0) need to disable too.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
While IS_ENABLED() is perfectly fine for CONFIG_* symbols, it is not
for other symbols such as __BIG_ENDIAN that is provided directly by
the compiler.
Switch to use CONFIG_CPU_BIG_ENDIAN instead of __BIG_ENDIAN.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
When CONFIG_PM_SLEEP is disabled, brcm_ahci_{suspend,resume} are not
used, which causes such a build warning to occur:
CC drivers/ata/ahci_brcmstb.o
drivers/ata/ahci_brcmstb.c:212:12: warning: 'brcm_ahci_suspend' defined
but not used [-Wunused-function]
static int brcm_ahci_suspend(struct device *dev)
^
drivers/ata/ahci_brcmstb.c:224:12: warning: 'brcm_ahci_resume' defined
but not used [-Wunused-function]
static int brcm_ahci_resume(struct device *dev)
^
LD drivers/ata/built-in.o
Fixes: 766a2d9796 ("ata: add Broadcom AHCI SATA3 driver for STB chips")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pretty straightforward driver, using the nice library-ization of the
generic ahci_platform driver.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Danesh Petigara