We found a bug that i2c transfer sometimes failed on 3066a board with
stabel-4.8, the con register would be updated by uninitialized tuning
value, it made the i2c transfer failed.
So give the tuning value to be zero during rk3x_i2c_v0_calc_timings.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Pull i2c updates from Wolfram Sang:
"Here is the 4.9 pull request from I2C including:
- centralized error messages when registering to the core
- improved lockdep annotations to prevent false positives
- DT support for muxes, gates, and arbitrators
- bus speeds can now be obtained from ACPI
- i2c-octeon got refactored and now supports ThunderX SoCs, too
- i2c-tegra and i2c-designware got a bigger bunch of updates
- a couple of standard driver fixes and improvements"
* 'i2c/for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (71 commits)
i2c: axxia: disable clks in case of failure in probe
i2c: octeon: thunderx: Limit register access retries
i2c: uniphier-f: fix misdetection of incomplete STOP condition
gpio: pca953x: variable 'id' was used twice
i2c: i801: Add support for Kaby Lake PCH-H
gpio: pca953x: fix an incorrect lockdep warning
i2c: add a warning to i2c_adapter_depth()
lockdep: make MAX_LOCKDEP_SUBCLASSES unconditionally visible
i2c: export i2c_adapter_depth()
i2c: rk3x: Fix variable 'min_total_ns' unused warning
i2c: rk3x: Fix sparse warning
i2c / ACPI: Do not touch an I2C device if it belongs to another adapter
i2c: octeon: Fix high-level controller status check
i2c: octeon: Avoid sending STOP during recovery
i2c: octeon: Fix set SCL recovery function
i2c: rcar: add support for r8a7796 (R-Car M3-W)
i2c: imx: make bus recovery through pinctrl optional
i2c: meson: add gxbb compatible string
i2c: uniphier-f: set the adapter to master mode when probing
i2c: uniphier-f: avoid WARN_ON() of clk_disable() in failure path
...
This patch fixs the following warning:
drivers/i2c/busses/i2c-rk3x.c: In function 'rk3x_i2c_v1_calc_timings':
drivers/i2c/busses/i2c-rk3x.c:745:41: warning: variable 'min_total_ns' set but not used [-Wunused-but-set-variable]
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch fixes the following sparse warning:
drivers/i2c/busses/i2c-rk3x.c:888:17: warning: cast truncates bits from constant value (ffffffffff00 becomes ffffff00)
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Depending on a number of factors including:
- Which exact Rockchip SoC we're working with
- How deep we suspend
- Which i2c port we're on
We might lose the state of the i2c registers at suspend time.
Specifically we've found that on rk3399 the i2c ports that are not in
the PMU power domain lose their state with the current suspend depth
configured by ARM Tursted Firmware.
Note that there are very few actual i2c registers that aren't configured
per transfer anyway so all we actually need to re-configure are the
clock config registers. We'll just add a call to rk3x_i2c_adapt_div()
at resume time and be done with it.
NOTE: On rk3399 on ports whose power was lost, I put printouts in at
resume time. I saw things like:
before: con=0x00010300, div=0x00060006
after: con=0x00010200, div=0x00180025
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Tested-by: David Wu <david.wu@rock-chips.com>
[wsa: removed duplicate const]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The core will do this for us now.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Implement fast mode plus that allows bus speeds of up to 1MHz.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- new method to caculate i2c timings for rk3399:
There was an timing issue about "repeated start" time at the I2C
controller of version0, controller appears to drop SDA at .875x (7/8)
programmed clk high. On version 1 of the controller, the rule(.875x)
isn't enough to meet tSU;STA
requirements on 100k's Standard-mode. To resolve this issue,
sda_update_config, start_setup_config and stop_setup_config for I2C
timing information are added, new rules are designed to calculate
the timing information at new v1.
- pclk and function clk are separated at rk3399
Signed-off-by: David Wu <david.wu@rock-chips.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
[wsa: fixed whitespace issue]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c timing specs are really just constant data. There's no reason
to write code to init them, so move them out to structures. This not
only is a cleaner solution but it will reduce code duplication when we
introduce a new variant of rk3x_i2c_calc_divs() in a future patch.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Suggested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Specifying the i2c SoC data in an array provides very little benefit and
gets unwieldly / confusing as the array grows since the next bit of code
needs to refer to elements in the array by their raw integral index.
Let's just create a single 'static const' structure for each SoC so that
we can refer to these structures by ID.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Suggested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
rk3x_i2c_setup() gets called directly before rk3x_i2c_start(),
and the last thing in setup was to clean the IPD, so no reason
to do it at the beginning of start.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The "div_high" and "div_low" values are always used together.
Group them into a structure to make it easier to pass them
both around. This structure also provides a place for future
calculated timings.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add kernel-doc documentation for the elements of the previously
undocumented struct rk3x_i2c.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
- Peter Rosin did some major rework on the locking of i2c muxes by
seperating parent-locked muxes and mux-locked muxes.
This avoids deadlocks/workarounds when the mux itself needs i2c
commands for muxing. And as a side-effect, other workarounds in the
media layer could be eliminated. Also, Peter stepped up as the i2c
mux maintainer and will keep an eye on these changes.
- major updates to the octeon driver
- add a helper to the core to generate the address+rw_bit octal and
make drivers use it
- quite a bunch of driver updates
* 'i2c/for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (84 commits)
i2c: rcar: add DMA support
i2c: st: Implement bus clear
i2c: only check scl functions when using generic recovery
i2c: algo-bit: declare i2c_bit_quirk_no_clk_stretch as static
i2c: tegra: disable clock before returning error
[media] rtl2832: regmap is aware of lockdep, drop local locking hack
[media] rtl2832_sdr: get rid of empty regmap wrappers
[media] rtl2832: change the i2c gate to be mux-locked
[media] si2168: change the i2c gate to be mux-locked
iio: imu: inv_mpu6050: change the i2c gate to be mux-locked
i2c: mux: document i2c muxes and elaborate on parent-/mux-locked muxes
i2c: mux: relax locking of the top i2c adapter during mux-locked muxing
i2c: muxes always lock the parent adapter
i2c: allow adapter drivers to override the adapter locking
i2c: uniphier: add "\n" at the end of error log
i2c: mv64xxx: remove CONFIG_HAVE_CLK conditionals
i2c: mv64xxx: use clk_{prepare_enable,disable_unprepare}
i2c: mv64xxx: handle probe deferral for the clock
i2c: mv64xxx: enable the driver on ARCH_MVEBU
i2c: octeon: Add workaround for broken irqs on CN3860
...
Switch to the new generic functions: i2c_parse_fw_timings().
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable the I2C core for this SoC.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Although unlikely, it is remotely possible for an i2c command to need
more than 200ms complete. Unlike smbus, i2c devices can clock stretch
for an unspecified amount of time. The longest time I've seen
specified for a device is 144ms (bq27541 battery gas), but one could
imagine a device taking a bit slower. 1 second "ought to be enough for
anyone."
The above is not the only justifcation for going above 200ms for a
timeout, though. It turns out that if you've got a large number of
printks going out to a serial console, interrupts on a CPU can be
disabled for hundreds of milliseconds. That's not a great situation to
be in to start with (maybe we should put a cap in vprintk_emit()) but
it's pretty annoying to start seeing unexplained i2c timeouts.
Note that to understand why we can timeout when printk has interrupts
disabled, you need to understand that on current Linux ARM kernels
interrupts are routed to a single CPU in a multicore system. Thus,
you can get:
1. CPU1 is running rk3x_i2c_xfer()
2. CPU0 calls vprintk_emit(), which disables all IRQs on CPU0.
3. I2C interrupt is ready but is set to only run on CPU0, where IRQs
are disabled.
4. CPU1 timeout expires. I2C interrupt is still ready, but CPU0 is
still sitting in the same vprintk_emit()
5. CPU1 sees that no interrupt happened in 200ms, so timeout.
A normal system shouldn't see i2c timeouts anyway, so increasing the
timeout should help people debugging without hurting other people
excessively.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
master_xfer() method should return number of i2c messages transferred,
but on Rockchip we were usually returning just 1, which caused trouble
with users that actually check number of transferred messages vs.
checking for negative error codes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
On Rockchip I2C the controller drops SDA low slightly too soon to meet
the "repeated start" requirements.
>From my own experimentation over a number of rates:
- controller appears to drop SDA at .875x (7/8) programmed clk high.
- controller appears to keep SCL high for 2x programmed clk high.
The first rule isn't enough to meet tSU;STA requirements in
Standard-mode on the system I tested on. The second rule is probably
enough to meet tHD;STA requirements in nearly all cases (especially
after accounting for the first), but it doesn't hurt to account for it
anyway just in case.
Even though the repeated start requirement only need to be accounted
for during a small part of the transfer, we'll adjust the timings for
the whole transfer to meet it. I believe that adjusting the timings
in just the right place to switch things up for repeated start would
require several extra interrupts and that doesn't seem terribly worth
it.
With this change and worst case rise/fall times, I see 100kHz i2c
going to ~85kHz. With slightly optimized rise/fall (800ns / 50ns) I
see i2c going to ~89kHz. Fast-mode isn't affected much because
tSU;STA is shorter relative to tHD;STA there.
As part of this change we needed to account for the SDA falling time.
The specification indicates that this should be the same, but we'll
follow Designware's lead and add a binding. Note that we deviate from
Designware and assign the default SDA falling time to be the same as
the SCL falling time, which is incredibly likely.
Signed-off-by: Doug Anderson <dianders@chromium.org>
[wsa: rebased to i2c/for-next]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The number of clock cycles to be written into the CLKDIV register
that determines the I2C clk high phase includes the rise time.
So to meet the timing requirements defined in the I2C specification
which defines the minimal time SCL has to be high, the rise time
has to taken into account. The same applies to the low phase with
falling time.
In my test on RK3288-Pink2 board, which is not an upstream board yet,
if external pull-up resistor is 4.7K, rise_ns is about 700ns.
So the measured high_ns is about 3900ns, which is less than 4000ns
(the minimum high_ns in I2C specification for Standard-mode).
To fix this bug min_low_ns should include fall time and min_high_ns
should include rise time.
This patch merged the patch from chromium project which can get the
rise and fall times for signals from the device tree. This allows us
to more accurately calculate timings. see:
https://chromium-review.googlesource.com/#/c/232774/
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
[wsa: fixed a typo in the docs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
The i2c input clock can change dynamically, e.g. on the RK3066 where
pclk_i2c0 and pclk_i2c1 are connected to the armclk, which changes
rate on cpu frequency scaling.
Until now, we incorrectly called clk_get_rate() while holding the
i2c->lock in rk3x_i2c_xfer() to adapt to clock rate changes.
Thanks to Huang Tao for reporting this issue.
Do it properly now using the clk notifier framework. The callback
logic was taken from i2c-cadence.c.
Also rename all misleading "i2c_rate" variables to "clk_rate", as they
describe the *input* clk rate.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Tested-by: Doug Anderson <dianders@chromium.org> on RK3288
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As show in I2C specification:
- Standard-mode: the minimum HIGH period of the scl clock is 4.0us
the minimum LOW period of the scl clock is 4.7us
- Fast-mode: the minimum HIGH period of the scl clock is 0.6us
the minimum LOW period of the scl clock is 1.3us
I have measured i2c SCL waveforms in fast-mode by oscilloscope
on rk3288-pinky board. the LOW period of the scl clock is 1.3us.
It is so critical that we must adjust LOW division to increase
the LOW period of the scl clock.
Thanks Doug for the suggestion about division formulas.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"Highlights from the I2C subsystem for 3.18:
- new drivers for Axxia AM55xx, and Hisilicon hix5hd2 SoC.
- designware driver gained AMD support, exynos gained exynos7 support
The rest is usual driver stuff. Hopefully no lowlights this time"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i801: Add Device IDs for Intel Sunrise Point PCH
i2c: hix5hd2: add i2c controller driver
i2c-imx: Disable the clock on probe failure
i2c: designware: Add support for AMD I2C controller
i2c: designware: Rework probe() to get clock a bit later
i2c: designware: Default to fast mode in case of ACPI
i2c: axxia: Add I2C driver for AXM55xx
i2c: exynos: add support for HSI2C module on Exynos7
i2c: mxs: detect No Slave Ack on SELECT in PIO mode
i2c: cros_ec: Remove EC_I2C_FLAG_10BIT
i2c: cros-ec-tunnel: Add of match table
i2c: rcar: remove sign-compare flaw
i2c: ismt: Use minimum descriptor size
i2c: imx: Add arbitration lost check
i2c: rk3x: Remove unlikely() annotations
i2c: rcar: check for no IRQ in rcar_i2c_irq()
i2c: rcar: make rcar_i2c_prepare_msg() *void*
i2c: rcar: simplify check for last message
i2c: designware: add support of platform data to set I2C mode
i2c: designware: add support of I2C standard mode
i2cdetect -q was broken (everything was a false positive, and no transfers were
actually being sent over i2c). The way it works is by sending a 0 length write
request and checking for NACK. This patch fixes the 0 length writes and actually
sends them.
Reported-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Tested-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Having a transfer more than 32 bits is not all that unlikely. Remove
the annotation.
The unlikely in the IRQ handler can't gain us much. It's not in a
loop, so at most it would save 1 instruction per IRQ, which isn't
much. In fact on the compiler I tested it produced the exact same
code. Remove it too.
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C_CLKDIV register descripted in the previous version of
RK3x chip manual is incorrect. Plus 1 is required.
The correct formula:
- T(SCL_HIGH) = T(PCLK) * (CLKDIVH + 1) * 8
- T(SCL_LOW) = T(PCLK) * (CLKDIVL + 1) * 8
- (SCL Divsor) = 8 * ((CLKDIVL + 1) + (CLKDIVH + 1))
- SCL = PCLK / (CLK Divsor)
It will be updated to the latest version of chip manual.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
In rk3x SOC, the I2C controller can receive/transmit up to 32 bytes data
in one chunk, so the size of data to be write/read to/from TXDATAx/RXDATAx
must be less than or equal 32 bytes at a time.
Tested on rk3288-pinky board, elan receive 158 bytes data.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Acked-by: Max Schwarz <max.schwarz@online.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
If slave holds scl, I2C_IPD[7] will be set 1 by controller
for debugging. Driver must ignore it.
[ 5.752391] rk3x-i2c ff160000.i2c: unexpected irq in WRITE: 0x80
[ 5.939027] rk3x-i2c ff160000.i2c: timeout, ipd: 0x80, state: 4
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
drivers/i2c/busses/i2c-rk3x.c:610:69-70: rk3x_i2c_match is not NULL terminated at line 610
Make sure of_device_id tables are NULL terminated
Generated by: /kbuild/src/linux/scripts/coccinelle/misc/of_table.cocci
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Driver for the native I2C adapter found in Rockchip RK3xxx SoCs.
Configuration is only possible through devicetree. The driver is
interrupt driven and supports the I2C_M_IGNORE_NAK mangling bit.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
David Wu