This change fixes HS400 tuning for devices with invalid presets.
SDHCI presets are not currently used for eMMC HS/HS200/HS400, but are
used for DDR52. The HS400 retuning sequence is:
HS400->DDR52->HS->HS200->Perform Tuning->HS->HS400
This means that when HS400 tuning happens, we transition through DDR52
for a very brief period. This causes presets to be enabled
unintentionally and stay enabled when transitioning back to HS200 or
HS400. Some firmware has invalid presets, so we end up with driver
strengths that can cause I/O problems.
Fixes: 34597a3f60 ("mmc: sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400")
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200928154718.1.Icc21d4b2f354e83e26e57e270dc952f5fe0b0a40@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With the new SW tuning App note[1], a custom tuning algorithm is
required for eMMC HS200, HS400 and SD card UHS modes. The algorithm
involves running through the 32 possible input tap delay values and
sending the appropriate tuning command (CMD19/21) for each of them
to get a fail or pass result for each of the values. Typically, the
range will have a small contiguous failing window. Considering the
tuning range as a circular buffer, the algorithm then sets a final
tuned value directly opposite to the failing window.
[1] https://www.ti.com/lit/pdf/spract9
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20200923105206.7988-6-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DLL need only be enabled for speed modes and clock frequencies at or
above 50 MHz. For speed modes that don't enable the DLL, we need to
configure a static input delay value. This involves reading an optional
itap-del-sel-* value from the device tree and configuring it for the
appropriate speed mode.
With this addition, make sure that DLL is always switched off at the
beginning of the set_clock() call to simplify configuration. This also
removes the need for the dll_on member in struct sdhci_am654_data.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200923105206.7988-5-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The bit ESDHC_PERIPHERAL_CLK_SEL to select using peripheral clock
or platform clock is not able to be reset by SDHCI_RESET_ALL.
So driver needs to initialize it as 1 or 0 once, to override the
different value which may be configured in bootloader.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Link: https://lore.kernel.org/r/20200927082304.9232-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit bedf9fc01f ("mmc: sdhci: Workaround broken command queuing on
Intel GLK"), disabled command-queuing on Intel GLK based LENOVO models
because of it being broken due to what is believed to be a bug in
the BIOS.
It seems that the BIOS of some IRBIS models, including the IRBIS NB111
model has the same issue, so disable command queuing there too.
Fixes: bedf9fc01f ("mmc: sdhci: Workaround broken command queuing on Intel GLK")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209397
Reported-and-tested-by: RussianNeuroMancer <russianneuromancer@ya.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200927104821.5676-1-hdegoede@redhat.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a littler helper to make the somewhat arcane bd_contains checks a
little more obvious.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The struct of_device_id is not defined with !CONFIG_OF so its forward
declaration should be hidden to as well. This should address clang
compile warning:
drivers/mmc/host/sdhci-s3c.c:464:34: warning: tentative array definition assumed to have one element
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200925072532.10272-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The 'struct mmc_host *mmc' comes from drvdata set at the end of probe,
so it cannot be NULL. The code already dereferences it few lines before
the check with mmc_priv(). This also fixes smatch warning:
drivers/mmc/host/moxart-mmc.c:692 moxart_remove() warn: variable dereferenced before check 'mmc' (see line 688)
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200923153739.30327-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC core has now a generic check if some tuning is in progress. Its
protected area is a bit larger than the custom one in this driver but we
concluded that this works equally well for the intended case. So, drop
the local flag and switch to the generic one.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200922172253.4458-1-wsa@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The BDI_CAP_STABLE_WRITES is one of the few bits of information in the
backing_dev_info shared between the block drivers and the writeback code.
To help untangling the dependency replace it with a queue flag and a
superblock flag derived from it. This also helps with the case of e.g.
a file system requiring stable writes due to its own checksumming, but
not forcing it on other users of the block device like the swap code.
One downside is that we an't support the stable_pages_required bdi
attribute in sysfs anymore. It is replaced with a queue attribute which
also is writable for easier testing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The MediaTek MMC driver uses pointer to get from private
msdc_host structure to the generic mmc_host structure.
However mmc_host always precedes msdc_host in memory so compute
its address with a subtraction (which is cheaper than a dereference)
using mmc_from_priv() and drop the extra pointer.
Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com>
Link: https://lore.kernel.org/r/20200917192624.548720-1-ameynarkhede03@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reorganize the code, so that the flag is always cleared independently of
a good or bad case.
Fixes: 97a7d87e96 ("mmc: core: add a 'doing_init_tune' flag and a 'mmc_doing_tune' helper")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200914112845.21855-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If CONFIG_NO_DMA=y (e.g. Sun-3 allmodconfig):
drivers/mmc/host/mmc_spi.c:1323:15: warning: return type defaults to ‘int’ [-Wreturn-type]
static inline mmc_spi_dma_alloc(struct mmc_spi_host *host) { return 0; }
^~~~~~~~~~~~~~~~~
Fix this by adding the missing return type.
Fixes: a395acf0f6 ("mmc: mmc_spi: Allow the driver to be built when CONFIG_HAS_DMA is unset")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20200914094243.3912-1-geert@linux-m68k.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
-----BEGIN PGP SIGNATURE-----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=bjMI
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/soc
Samsung S3C24xx and S3C64xx machine code cleanup for v5.10
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
* tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (62 commits)
ARM: s3c: Avoid naming clash of S3C24xx and S3C64xx timer setup
ARM: s3c: Cleanup from old plat-samsung include
ARM: s3c: make headers local if possible
ARM: s3c: move into a common directory
ARM: s3c24xx: stop including mach/hardware.h from mach/io.h
cpufreq: s3c24xx: move low-level clk reg access into platform code
cpufreq: s3c2412: use global s3c2412_cpufreq_setrefresh
ARM: s3c: remove cpufreq header dependencies
cpufreq: s3c24xx: split out registers
fbdev: s3c2410fb: remove mach header dependency
ARM: s3c24xx: bast: avoid irq_desc array usage
ARM: s3c24xx: spi: avoid hardcoding fiq number in driver
ARM: s3c24xx: include mach/irqs.h where needed
ARM: s3c24xx: move s3cmci pinctrl handling into board files
ARM: s3c24xx: move iis pinctrl config into boards
ARM: s3c24xx: move spi fiq handler into platform
ARM: s3c: adc: move header to linux/soc/samsung
ARM: s3c24xx: move irqchip driver back into platform
ARM: s3c24xx: move regs-spi.h into spi driver
ARM: s3c64xx: remove mach/hardware.h
...
Link: https://lore.kernel.org/r/20200831154751.7551-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
dev_pm_opp_of_remove_table() doesn't report any errors when it fails to
find the OPP table with error -ENODEV (i.e. OPP table not present for
the device). And we can call dev_pm_opp_of_remove_table()
unconditionally here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/890ae5601594fca5de104695a682f4b6efbc631b.1599660554.git.viresh.kumar@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some R-Car Gen3 SoCs need some manual correction of timing parameters
after the automatic tuning has finished but before next CMD13 is
completed. This patch implements that by this state machine:
- introducing a per-SoC correction table if needed
- iff such a table exists, the 'fixup_request' callback is populated
during probe
- iff such a table exists, a runtime flag ('needs_adjust_hs400')
is set when HS400 tuning was completed
- the callback will check the runtime flag and enable the corrected
manual mode if the flag is set and CMD13 is encountered
- at the end of the enablement the runtime flag is cleared
- iff the configuration flag is set, the manual mode will be disabled
when HS400 gets downgraded
There also some helper functions added to access the TMPPORT registers.
The actual correction table is SoC and instance(!) specific and is
added to the quirks struct.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20200902081812.1591-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers. This batch converts
the drivers that appeared to have been added after kernel 5.4.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Lars Povlsen <lars.povlsen@microchip.com>
Acked-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200903162412.6.Ib121debfb18e5f923a3cd38fe9c36aa086c650c5@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers. This batch converts
the drivers that appeared to be around in the v5.4 timeframe.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200903162412.5.I2b630c4d40ff4ea61d5b30b8ccfe95890e257100@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers. This batch converts
the drivers that appeared to be around in the v4.19 timeframe.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200903162412.4.I84eb3e0a738635d524c90d1a688087bc295f7c32@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers. This batch converts
the drivers that appeared to be around in the v4.14 timeframe.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> # SDHI drivers
Link: https://lore.kernel.org/r/20200903162412.3.Id1ff21470f08f427aedd0a6535dcd83ccc56b278@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers. This batch converts
the drivers that appeared to be around in the v4.9 timeframe.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200903162412.2.I226782b43191ce367fa3bc1c907c29f571890412@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers. This batch converts
the drivers that appeared to be around in the v4.4 timeframe.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> # SH_MMCIF
Tested-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200903162412.1.Id501e96fa63224f77bb86b2135a5e8324ffb9c43@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Multiple MMC host controller driver can be compile tested as they do not
depend on architecture specific headers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907105254.31097-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All entries in Kconfig are already part of "if MMC", so there is no need
for additional dependency on MMC.
Suggested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200904164315.24618-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit 9495b7e92f ("driver core: platform: Initialize dma_parms
for platform devices"), struct platform_device already provides a
dma_parms structure, so we can save allocating another one.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/85e1fc97dbec3dea96102785a5e308ccb5e91cfe.1599167798.git.robin.murphy@arm.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Because clk_disable_unprepare already checked NULL clock parameter, so the
additional checks are unnecessary, just remove them.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Link: https://lore.kernel.org/r/20200903084825.85616-1-vulab@iscas.ac.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We already have 'host' as a variable, so use it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200901150250.26236-5-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tuning procedure switches to lower frequencies but that will turn the
SCC off and accessing its register then will hang. So, check when we are
tuning and keep the current setup of the external clock if we are doing
so. Note that we still switch to the lower frequency because of the
internal divider. We just make sure to not modify the external clock.
This patch depends on a MMC core patch calling the downgrade function
earlier.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200901150250.26236-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Our driver needs to know when tuning is in progress. 'doing_retune' only
covers re-tuning, not the initial tuning. Add another flag to detect the
initial tuning state and add a helper which tells us if any kind of
tuning is going on. Only implemented for MMC currently because that's
where we need it. SD can be added later if it becomes necessary.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200901150250.26236-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver specific downgrade function makes more sense if we run it
before we set the timing to something lower, not after. Otherwise some
non-HS400 communication has already happened.
No need to convert users. There is only one currently which needs this
change in a following patch.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200901150250.26236-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Turning on initcall debug on one system showed this:
initcall sdhci_msm_driver_init+0x0/0x28 returned 0 after 34782 usecs
The lion's share of this time (~33 ms) was in mmc_power_up(). This
shouldn't be terribly surprising since there are a few calls to delay
based on "power_delay_ms" and the default delay there is 10 ms.
Because we haven't specified that we'd prefer asynchronous probe for
this driver then we'll wait for this driver to finish before we start
probes for more drivers. While 33 ms doesn't sound like tons, every
little bit counts.
There should be little problem with turning on asynchronous probe for
this driver. It's already possible that previous drivers may have
turned on asynchronous probe so we might already have other things
(that probed before us) probing at the same time we are anyway. This
driver isn't really providing resources (clocks, regulators, etc) that
other drivers need to probe and even if it was they should be handling
-EPROBE_DEFER.
Let's turn this on and get a bit of boot speed back.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200902164303.1.I5e598a25222b4534c0083b61dbfa4e0e76f66171@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The 'imask' and 'bsize' are not used in dbg_dumpregs:
drivers/mmc/host/s3cmci.c:149:36: warning: variable 'imask' set but not used [-Wunused-but-set-variable]
drivers/mmc/host/s3cmci.c:148:63: warning: variable 'bsize' set but not used [-Wunused-but-set-variable]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200903054333.18331-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since driver data is a pointer, direct casting to integer causes
warning when compile testing for 64-bit architecture:
drivers/mmc/host/s3cmci.c:1495:17: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
The actual driver data can be only 0 or 1, so cast it via long and do
not care about any loss of value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902204847.2764-3-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
iomem pointers should be printed with pointer format to hide the
actual value and fix warnings when compile testing for 64-bit
architecture:
drivers/mmc/host/s3cmci.c:1355:46: warning:
cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902204847.2764-2-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Store in interrupt service routine always '1' in end_command, not the
value of host->cmd to fix compile test warnings on RISC-V:
drivers/mmc/host/davinci_mmc.c:999:17: warning:
cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902204847.2764-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Only -ENOENT from devm_clk_get() means that clock is not present in
device tree. Other errors have their own meaning and should not be
ignored.
Simplify getting the clock which is in fact optional and also use
dev_err_probe() for handling deferred.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200902193658.20539-7-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dma_addr_t size varies between architectures so use dedicated printk
format to fix compile testing warning (e.g. on 32-bit MIPS):
drivers/mmc/host/sdhci-of-sparx5.c:63:11: warning:
format ‘%llx’ expects argument of type ‘long long unsigned int’, but argument 5 has type ‘dma_addr_t {aka unsigned int}’ [-Wformat=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902193658.20539-11-krzk@kernel.org
Acked-by: Lars Povlsen <larc.povlsen@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code, the error value gets printed and real error
from dw_mci_parse_dt() is passed further instead of fixed -EINVAL.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902193658.20539-10-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902193658.20539-9-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902193658.20539-8-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902193658.20539-6-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902193658.20539-5-krzk@kernel.org
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902193658.20539-4-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902193658.20539-3-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200902193658.20539-2-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As with GPIO, UART and others, allow specifying the device index via the
aliases node in the device tree.
On embedded devices, there is often a combination of removable (e.g.
SD card) and non-removable MMC devices (e.g. eMMC).
Therefore the index might change depending on
* host of removable device
* removable card present or not
This makes it difficult to hardcode the root device, if it is on the
non-removable device. E.g. if SD card is present eMMC will be mmcblk1,
if SD card is not present at boot, eMMC will be mmcblk0.
Alternative solutions like PARTUUIDs do not cover the case where multiple
mmcblk devices contain the same image. This is a common issue on devices
that can boot both from eMMC (for regular boot) and SD cards (as a
temporary boot medium for development). When a firmware image is
installed to eMMC after a test boot via SD card, there will be no
reliable way to refer to a specific device using (PART)UUIDs oder
LABELs.
The demand for this feature has led to multiple attempts to implement
it, dating back at least to 2012 (see
https://www.spinics.net/lists/linux-mmc/msg26586.html for a previous
discussion from 2014).
All indices defined in the aliases node will be reserved for use by the
respective MMC device, moving the indices of devices that don't have an
alias up into the non-reserved range. If the aliases node is not found,
the driver will act as before.
This is a rebased and cleaned up version of
https://www.spinics.net/lists/linux-mmc/msg26588.html .
Based-on-patch-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lkml.org/lkml/2020/8/5/194
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20200901085004.2512-2-matthias.schiffer@ew.tq-group.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The emmc2 interface on the bcm2711 supports DDR modes for eMMC devices
running at 3.3V. This allows to run eMMC module with 3.3V signaling voltage
at DDR52 mode on the Raspberry Pi 4 using a SD adapter:
clock: 52000000 Hz
actual clock: 50000000 Hz
vdd: 21 (3.3 ~ 3.4 V)
bus mode: 2 (push-pull)
chip select: 0 (don't care)
power mode: 2 (on)
bus width: 2 (4 bits)
timing spec: 8 (mmc DDR52)
signal voltage: 0 (3.30 V)
driver type: 0 (driver type B)
Link: https://github.com/raspberrypi/linux/issues/3802
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1598651234-29826-1-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CQHCI_ENABLE bit in CQHCI_CFG should be disabled
after msdc_cqe_disable(), and should be enabled before
msdc_ceq_enable() for MTK platform.
Add hook functions for cqhci_host_ops->pre_enable() and
cqhci_host_ops->post_disable().
Signed-off-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1598520783-25250-3-git-send-email-chun-hung.wu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add pre_enable() and post_disable() for cqhci_host_ops.
Add hook functions before cqhci enable and
after cqhci disable for platforms need them.
Signed-off-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1598520783-25250-2-git-send-email-chun-hung.wu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On sc7180 target, issues are observed with HS400 mode due to a
hardware limitation. If sdcc clock is dynamically gated and ungated,
the very next command is failing with command CRC/timeout errors.
To mitigate this issue, DLL phase has to be restored whenever sdcc
clock is gated dynamically. The restore_dll_config ensures this.
Enabling this flag with this change. And simply re-using the sdm845
target configuration for this flag.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/1598541694-15694-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After all the previous refactorization, we can now populate mmc_ops
directly and don't need a layer inbetween. The NULL-pointer check and
the error printout are already done by the MMC core.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-7-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHI needs to reset the SCC only, not the whole IP core. So, if tuning
fails, don't handle specifics in the generic TMIO core, but in the
specific drivers. For SDHI, we need to move around the reset routine a
bit. It is not modified.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-6-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some TMIO variants need specific actions in their reset routine, but
they are all based on a generic reset routine. So, the optional 'reset'
callback will now only take care of the additional stuff and we will
have a generic function around it. Less code, easier to maintain, and
much more readable. Code in tmio_mmc.c is untested but in my TC6387XB
datasheet the SDIO part is reset independently from the SD part, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-5-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After Yamada-san's refactorization introducing 'tmio_mmc_host_alloc', we
can populate mmc_ops directly and don't need a layer inbetween.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit a87852c6b8. It did fix
the issue, but was building on top of already wrong assumptions. The
driver missed that 'hw_reset' was only for resetting remote HW (card)
and not for the IP core. Since we fixed that in a previous patch, we can
now remove this patch to make it clear that 'reset' is for resetting the
IP core only. Also, cancelling DMA will only be called when actually
needed again. It will also allow for further cleanups and better
readability. Note that in addition to the revert, the call in
'tmio_mmc_execute_tuning' will be converted, too, to maintain the
current behaviour.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver got the usage of 'hw_reset' wrong and missed that it is used
to reset the remote HW (card) only, not the local one (controller). Move
everything to the proper 'reset' callback. Also, add the generic reset
code from TMIO, so we will ensure the same behaviour (it will get
refactored away in a later patch). This also means we need to drop
MMC_CAP_HW_RESET because this is currently not supported by our
hardware.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a one time delay because of a card detect debounce timer in the
controller IP. This timer runs as soon as power is applied to the module
regardless of whether a card is present or not and any writes to
SDHCI_POWER_ON will return 0 before it expires. This timeout has been
measured to be about 1 second in am654x and j721e.
Write-and-read-back in a loop on SDHCI_POWER_ON for a maximum of
1.5 seconds to make sure that the controller actually powers on.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200825170015.32285-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There seems to be no particular reason to only test for ARM, so allow
for build-testing on other platforms to increase coverage.
Build-tested on x86 with allyesconfig.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Link: https://lore.kernel.org/r/20200824171854.406157-1-alex.dewar90@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This adds the eMMC driver for the Sparx5 SoC. It is based upon the
designware IP, but requires some extra initialization and quirks.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200825081357.32354-3-lars.povlsen@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
via_save_pcictrlreg() should be called with host->lock held
as it writes to pm_pcictrl_reg, otherwise there can be a race
condition between via_sd_suspend() and via_sdc_card_detect().
The same pattern is used in the function via_reset_pcictrl()
as well, where via_save_pcictrlreg() is called with host->lock
held.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Link: https://lore.kernel.org/r/20200822061528.7035-1-madhuparnabhowmik10@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some Intel BYT based host controllers support the setting of latency
tolerance. Accordingly, implement the PM QoS ->set_latency_tolerance()
callback. The raw register values are also exposed via debugfs.
Intel EHL controllers require this support.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: cb3a7d4a0a ("mmc: sdhci-pci: Add support for Intel EHL")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200818104508.7149-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When reading the test description, I thought a correction of the
xfer_size was tested, which is not the case. It is tested that the
xfer_size is correct. Use 'proper xfer_size' to remove this ambiguity.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200817115838.2981-1-wsa@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Previously the cycle timeout was converted to a microsecond value but
then incorrectly treated as a nanosecond timeout. This patch changes
the code to convert both the nanosecond timeout and the cycle timeout
to a microsecond value and use that directly.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Link: https://lore.kernel.org/r/20200814185011.3252020-1-t.schramm@manjaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For SDIO functions, SDIO cards and SD COMBO cards are exported revision
number and info strings from CISTPL_VERS_1 structure. Revision number
should indicate compliance of standard and info strings should contain
product information in same format as product information for PCMCIA cards.
Product information for PCMCIA cards should contain following strings in
this order: Manufacturer, Product Name, Lot number, Programming Conditions.
Note that not all SDIO cards export all those info strings in that order as
described in PCMCIA Metaformat Specification.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200727133837.19086-5-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Before parsing CISTPL_VERS_1 structure check that its size is at least two
bytes to prevent buffer overflow.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200727133837.19086-2-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to IC suggestion, everytime before sending the tuning command,
need to reset the usdhc, so to reset the tuning circuit, to let every
tuning command work well for the manual tuning method. For standard tuning
method, IC already add the reset operation in the hardware logic.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1597135057-22272-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove empty comment to fix W=1 compile warning:
drivers/mmc/host/s3cmci.c:400: warning: Cannot understand *
on line 400 - I thought it was a doc line
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200804151345.28005-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200718090614.88946-1-grandmaster@al2klimov.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI changed from using a tasklet to finish requests, to using an IRQ
thread i.e. commit c07a48c265 ("mmc: sdhci: Remove finish_tasklet").
Because this increased the latency to complete requests, a preparatory
change was made to complete the request from the IRQ handler if
possible i.e. commit 19d2f695f4 ("mmc: sdhci: Call mmc_request_done()
from IRQ handler if possible"). That alleviated the situation for MMC
block devices because the MMC block driver makes use of mmc_pre_req()
and mmc_post_req() so that successful requests are completed in the IRQ
handler and any DMA unmapping is handled separately in mmc_post_req().
However SDIO was still affected, and an example has been reported with
up to 20% degradation in performance.
Looking at SDIO I/O helper functions, sdio_io_rw_ext_helper() appeared
to be a possible candidate for making use of asynchronous requests
within its I/O loops, but analysis revealed that these loops almost
never iterate more than once, so the complexity of the change would not
be warrented.
Instead, mmc_pre_req() and mmc_post_req() are added before and after I/O
submission (mmc_wait_for_req) in mmc_io_rw_extended(). This still has
the potential benefit of reducing the duration of interrupt handlers, as
well as addressing the latency issue for SDHCI. It also seems a more
reasonable solution than forcing drivers to do everything in the IRQ
handler.
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Fixes: c07a48c265 ("mmc: sdhci: Remove finish_tasklet")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200903082007.18715-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit b214fe592a ("mmc: sdhci-of-esdhc: add erratum eSDHC7 support")
added code to check for a specific compatible string in the device-tree
on every esdhc interrupat. Instead of doing this record the quirk in
struct sdhci_esdhc and lookup the struct in esdhc_irq.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200903012029.25673-1-chris.packham@alliedtelesis.co.nz
Fixes: b214fe592a ("mmc: sdhci-of-esdhc: add erratum eSDHC7 support")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit cd57d07b1e ("sh: don't allow non-coherent DMA for NOMMU") made
CONFIG_NO_DMA to be set for some platforms, for good reasons.
Consequentially, CONFIG_HAS_DMA doesn't get set, which makes the DMA
mapping interface to be built as stub functions, but also prevent the
mmc_spi driver from being built as it depends on CONFIG_HAS_DMA.
It turns out that for some odd cases, the driver still relied on the DMA
mapping interface, even if the DMA was not actively being used.
To fixup the behaviour, let's drop the build dependency for CONFIG_HAS_DMA.
Moreover, as to allow the driver to succeed probing, let's move the DMA
initializations behind "#ifdef CONFIG_HAS_DMA".
Fixes: cd57d07b1e ("sh: don't allow non-coherent DMA for NOMMU")
Reported-by: Rich Felker <dalias@libc.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Rich Felker <dalias@libc.org>
Link: https://lore.kernel.org/r/20200901150438.228887-1-ulf.hansson@linaro.org
As the comments in this patch say, if we tune and find all phases are
valid it's _almost_ as bad as no phases being found valid. Probably
all phases are not really reliable but we didn't detect where the
unreliable place is. That means we'll essentially be guessing and
hoping we get a good phase.
This is not just a problem in theory. It was causing real problems on
a real board. On that board, most often phase 10 is found as the only
invalid phase, though sometimes 10 and 11 are invalid and sometimes
just 11. Some percentage of the time, however, all phases are found
to be valid. When this happens, the current logic will decide to use
phase 11. Since phase 11 is sometimes found to be invalid, this is a
bad choice. Sure enough, when phase 11 is picked we often get mmc
errors later in boot.
I have seen cases where all phases were found to be valid 3 times in a
row, so increase the retry count to 10 just to be extra sure.
Fixes: 415b5a75da ("mmc: sdhci-msm: Add platform_execute_tuning implementation")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200827075809.1.If179abf5ecb67c963494db79c3bc4247d987419b@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 61d7437ed1 ("mmc: sdhci-acpi: Fix HS400 tuning for AMDI0040")
broke resume for eMMC HS400. When the system suspends the eMMC controller
is powered down. So, on resume we need to reinitialize the controller.
Although, amd_sdhci_host was not getting cleared, so the DLL was never
re-enabled on resume. This results in HS400 being non-functional.
To fix the problem, this change clears the tuned_clock flag, clears the
dll_enabled flag and disables the DLL on reset.
Fixes: 61d7437ed1 ("mmc: sdhci-acpi: Fix HS400 tuning for AMDI0040")
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200831150517.1.I93c78bfc6575771bb653c9d3fca5eb018a08417d@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit b5a84ecf02 ("mmc: tegra: Add Tegra210 support")
Tegra210 and later has a separate sdmmc_legacy_tm (TMCLK) used by Tegra
SDMMC hawdware for data timeout to achive better timeout than using
SDCLK and using TMCLK is recommended.
USE_TMCLK_FOR_DATA_TIMEOUT bit in Tegra SDMMC register
SDHCI_TEGRA_VENDOR_SYS_SW_CTRL can be used to choose either TMCLK or
SDCLK for data timeout.
Default USE_TMCLK_FOR_DATA_TIMEOUT bit is set to 1 and TMCLK is used
for data timeout by Tegra SDMMC hardware and having TMCLK not enabled
is not recommended.
So, this patch adds quirk NVQUIRK_HAS_TMCLK for SoC having separate
timeout clock and keeps TMCLK enabled all the time.
Fixes: b5a84ecf02 ("mmc: tegra: Add Tegra210 support")
Cc: stable <stable@vger.kernel.org> # 5.4
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1598548861-32373-8-git-send-email-skomatineni@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit 4346b7c794 ("mmc: tegra: Add Tegra186 support")
SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK is set for Tegra186 from the
beginning of its support in driver.
Tegra186 SDMMC hardware by default uses timeout clock (TMCLK) instead
of SDCLK and this quirk should not be set.
So, this patch remove this quirk for Tegra186.
Fixes: 4346b7c794 ("mmc: tegra: Add Tegra186 support")
Cc: stable <stable@vger.kernel.org> # 5.4
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1598548861-32373-3-git-send-email-skomatineni@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit b5a84ecf02 ("mmc: tegra: Add Tegra210 support")
SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK is set for Tegra210 from the
beginning of Tegra210 support in the driver.
Tegra210 SDMMC hardware by default uses timeout clock (TMCLK)
instead of SDCLK and this quirk should not be set.
So, this patch remove this quirk for Tegra210.
Fixes: b5a84ecf02 ("mmc: tegra: Add Tegra210 support")
Cc: stable <stable@vger.kernel.org> # 5.4
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1598548861-32373-2-git-send-email-skomatineni@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch fixs eMMC-Access on mt7622/Bpi-64.
Before we got these Errors on mounting eMMC ion R64:
[ 48.664925] blk_update_request: I/O error, dev mmcblk0, sector 204800 op 0x1:(WRITE)
flags 0x800 phys_seg 1 prio class 0
[ 48.676019] Buffer I/O error on dev mmcblk0p1, logical block 0, lost sync page write
This patch adds a optional reset management for msdc.
Sometimes the bootloader does not bring msdc register
to default state, so need reset the msdc controller.
Cc: <stable@vger.kernel.org> # v5.4+
Fixes: 966580ad23 ("mmc: mediatek: add support for MT7622 SoC")
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20200814014346.6496-4-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For Intel controllers, SDHCI_RESET_ALL resets also CQHCI registers.
Normally, SDHCI_RESET_ALL is not used while CQHCI is enabled, but that can
happen on the error path. e.g. if mmc_cqe_recovery() fails, mmc_blk_reset()
is called which, for a eMMC that does not support HW Reset, will cycle the
bus power and the driver will perform SDHCI_RESET_ALL.
So whenever performing SDHCI_RESET_ALL ensure CQHCI is deactivated.
That will force the driver to reinitialize CQHCI when it is next used.
A similar change was done already for sdhci-msm, and other drivers using
CQHCI might benefit from a similar change, if they also have CQHCI reset
by SDHCI_RESET_ALL.
Fixes: 8ee82bda23 ("mmc: sdhci-pci: Add CQHCI support for Intel GLK")
Cc: stable@vger.kernel.org # 5.4.x: 0ffa6cfbd949: mmc: cqhci: Add cqhci_deactivate()
Cc: stable@vger.kernel.org # 5.4+
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200819121848.16967-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The AMD eMMC Controller can only use the tuned clock while in HS200 and
HS400 mode. If we switch to a different mode, we need to disable the
tuned clock. If we have previously performed tuning and switch back to
HS200 or HS400, we can re-enable the tuned clock.
Previously the tuned clock was not getting disabled when switching to
DDR52 which is part of the HS400 tuning sequence.
Fixes: 34597a3f60 ("mmc: sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400")
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200819125832.v2.1.Ie8f0689ec9f449203328b37409d1cf06b565f331@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rather than call the internal s3c_gpio_cfgall_range() function
through a platform header, move the code into the set_power
callback that is already exported by the board, and add
a default implementation.
In DT mode, the code already does not set the pin config,
so nothing changes there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200806182059.2431-29-krzk@kernel.org
[krzk: Rebase and correct set_power in mach-h1940.c]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The plat-samsung directory and mach-s5pv210 can be build
completely independently, so split the two Kconfig symbols
CONFIG_PLAT_SAMSUNG and CONFIG_ARCH_S5PV210.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-18-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Now that no code in arch/arm is shared between mach-exynos and the
others, make the split formal.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200806182059.2431-15-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The s3cmci driver does not use machine header mach/dma.h.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
static priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low' priority level,
plus sched_set_normal() to set the policy back to non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in a separate
tree.
When merging to the latest upstream tree there's a conflict in drivers/spi/spi.c,
which can be resolved via:
sched_set_fifo(ctlr->kworker_task);
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=/7JH
-----END PGP SIGNATURE-----
Merge tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull sched/fifo updates from Ingo Molnar:
"This adds the sched_set_fifo*() encapsulation APIs to remove static
priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low'
priority level, plus sched_set_normal() to set the policy back to
non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in
a separate tree"
* tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
sched,tracing: Convert to sched_set_fifo()
sched: Remove sched_set_*() return value
sched: Remove sched_setscheduler*() EXPORTs
sched,psi: Convert to sched_set_fifo_low()
sched,rcutorture: Convert to sched_set_fifo_low()
sched,rcuperf: Convert to sched_set_fifo_low()
sched,locktorture: Convert to sched_set_fifo()
sched,irq: Convert to sched_set_fifo()
sched,watchdog: Convert to sched_set_fifo()
sched,serial: Convert to sched_set_fifo()
sched,powerclamp: Convert to sched_set_fifo()
sched,ion: Convert to sched_set_normal()
sched,powercap: Convert to sched_set_fifo*()
sched,spi: Convert to sched_set_fifo*()
sched,mmc: Convert to sched_set_fifo*()
sched,ivtv: Convert to sched_set_fifo*()
sched,drm/scheduler: Convert to sched_set_fifo*()
sched,msm: Convert to sched_set_fifo*()
sched,psci: Convert to sched_set_fifo*()
sched,drbd: Convert to sched_set_fifo*()
...
- Add a new host cap bit and a corresponding DT property, to support power
cycling of the card by FW at system suspend/resume.
- Fix clock rate setting for SDIO in SDR12/SDR25 speed-mode
- Fix switch to 1/4-bit mode at system suspend/resume for SD-combo cards
- Convert the mmc-pwrseq DT bindings to the json-schema
- Always allow the card detect uevent to be consumed by userspace
MMC host:
- Convert a few DT bindings to the json-schema
- mtk-sd: Add support for command queue through cqhci
- mtk-sd: Add support for the MT6779 variant
- renesas_sdhi_internal_dmac: Fix dma unmapping in the error path
- sdhci_am654: Add support for the AM65x PG2.0 variant
- sdhci_am654: Extend support for phys/clocks
- sdhci-cadence: Drop incorrect HW tuning for SD mode
- sdhci-msm: Add support for interconnect bandwidth scaling
- sdhci-msm: Enable internal voltage control
- sdhci-msm: Enable low power state for pinctrls
- sdhci-of-at91: Ludovic Desroches handovers maintenance to Eugen Hristev
- sdhci-pci-gli: Improve clock handling for GL975x
- sdhci-pci-o2micro: Add HW tuning for SDR104 mode
- sdhci-pci-o2micro: Fix support for O2 host controller Seabird1
-----BEGIN PGP SIGNATURE-----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=AwwR
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add a new host cap bit and a corresponding DT property, to support
power cycling of the card by FW at system suspend/resume.
- Fix clock rate setting for SDIO in SDR12/SDR25 speed-mode
- Fix switch to 1/4-bit mode at system suspend/resume for SD-combo
cards
- Convert the mmc-pwrseq DT bindings to the json-schema
- Always allow the card detect uevent to be consumed by userspace
MMC host controllers:
- Convert a few DT bindings to the json-schema
- mtk-sd:
- Add support for command queue through cqhci
- Add support for the MT6779 variant
- renesas_sdhi_internal_dmac:
- Fix dma unmapping in the error path
- sdhci_am654:
- Add support for the AM65x PG2.0 variant
- Extend support for phys/clocks
- sdhci-cadence:
- Drop incorrect HW tuning for SD mode
- sdhci-msm:
- Add support for interconnect bandwidth scaling
- Enable internal voltage control
- Enable low power state for pinctrls
- sdhci-of-at91:
- Ludovic Desroches handovers maintenance to Eugen Hristev
- sdhci-pci-gli:
- Improve clock handling for GL975x
- sdhci-pci-o2micro:
- Add HW tuning for SDR104 mode
- Fix support for O2 host controller Seabird1"
* tag 'mmc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (66 commits)
mmc: mediatek: make function msdc_cqe_disable() static
MAINTAINERS: mmc: sdhci-of-at91: handover maintenance to Eugen Hristev
dt-bindings: mmc: mediatek: Add document for mt6779
mmc: mediatek: command queue support
mmc: mediatek: refine msdc timeout api
mmc: mediatek: add MT6779 MMC driver support
mmc: sdhci-pci-o2micro: Add HW tuning for SDR104 mode
mmc: sdhci-pci-o2micro: Bug fix for O2 host controller Seabird1
mmc: via-sdmmc: use generic power management
memstick: jmb38x_ms: use generic power management
mmc: sdhci-cadence: do not use hardware tuning for SD mode
mmc: sdhci-pci-gli: Set SDR104's clock to 205MHz and enable SSC for GL975x
mmc: cqhci: Fix a print format for the task descriptor
mmc: sdhci-of-arasan: fix timings allocation code
mmc: sdhci: Fix a potential uninitialized variable
dt-bindings: mmc: renesas,sdhi: convert to YAML
dt-bindings: mmc: convert arasan sdhci bindings to yaml
mmc: sdhci: Fix potential null pointer access while accessing vqmmc
mmc: core: Add MMC_CAP2_FULL_PWR_CYCLE_IN_SUSPEND
dt-bindings: mmc: Add full-pwr-cycle-in-suspend property
...
Here is the large set of char and misc and other driver subsystem
patches for 5.9-rc1. Lots of new driver submissions in here, and
cleanups and features for existing drivers.
Highlights are:
- habanalabs driver updates
- coresight driver updates
- nvmem driver updates
- huge number of "W=1" build warning cleanups from Lee Jones
- dyndbg updates
- virtbox driver fixes and updates
- soundwire driver updates
- mei driver updates
- phy driver updates
- fpga driver updates
- lots of smaller individual misc/char driver cleanups and fixes
Full details are in the shortlog.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXylccQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymofgCfZ1CxNWd0ZVM0YIn8cY9gO6ON7MsAnRq48hvn
Vjf4rKM73GC11bVF4Gyy
=Xq1R
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char and misc and other driver subsystem
patches for 5.9-rc1. Lots of new driver submissions in here, and
cleanups and features for existing drivers.
Highlights are:
- habanalabs driver updates
- coresight driver updates
- nvmem driver updates
- huge number of "W=1" build warning cleanups from Lee Jones
- dyndbg updates
- virtbox driver fixes and updates
- soundwire driver updates
- mei driver updates
- phy driver updates
- fpga driver updates
- lots of smaller individual misc/char driver cleanups and fixes
Full details are in the shortlog.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (322 commits)
habanalabs: remove unused but set variable 'ctx_asid'
nvmem: qcom-spmi-sdam: Enable multiple devices
dt-bindings: nvmem: SID: add binding for A100's SID controller
nvmem: update Kconfig description
nvmem: qfprom: Add fuse blowing support
dt-bindings: nvmem: Add properties needed for blowing fuses
dt-bindings: nvmem: qfprom: Convert to yaml
nvmem: qfprom: use NVMEM_DEVID_AUTO for multiple instances
nvmem: core: add support to auto devid
nvmem: core: Add nvmem_cell_read_u8()
nvmem: core: Grammar fixes for help text
nvmem: sc27xx: add sc2730 efuse support
nvmem: Enforce nvmem stride in the sysfs interface
MAINTAINERS: Add git tree for NVMEM FRAMEWORK
nvmem: sprd: Fix return value of sprd_efuse_probe()
drivers: android: Fix the SPDX comment style
drivers: android: Fix a variable declaration coding style issue
drivers: android: Remove braces for a single statement if-else block
drivers: android: Remove the use of else after return
drivers: android: Fix a variable declaration coding style issue
...
The sparse tool complains as follows:
drivers/mmc/host/mtk-sd.c:2269:6: warning:
symbol 'msdc_cqe_disable' was not declared. Should it be static?
This function is not used outside of mtk-sd.c, so this commit
marks it static.
Fixes: 88bd652b3c ("mmc: mediatek: command queue support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Link: https://lore.kernel.org/r/20200727171129.2945-1-weiyongjun1@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Make the Energy Model cover non-CPU devices (Lukasz Luba).
- Add Ice Lake server idle states table to the intel_idle driver
and eliminate a redundant static variable from it (Chen Yu,
Rafael Wysocki).
- Eliminate all W=1 build warnings from cpufreq (Lee Jones).
- Add support for Sapphire Rapids and for Power Limit 4 to the
Intel RAPL power capping driver (Sumeet Pawnikar, Zhang Rui).
- Fix function name in kerneldoc comments in the idle_inject power
capping driver (Yangtao Li).
- Fix locking issues with cpufreq governors and drop a redundant
"weak" function definition from cpufreq (Viresh Kumar).
- Rearrange cpufreq to register non-modular governors at the
core_initcall level and allow the default cpufreq governor to
be specified in the kernel command line (Quentin Perret).
- Extend, fix and clean up the intel_pstate driver (Srinivas
Pandruvada, Rafael Wysocki):
* Add a new sysfs attribute for disabling/enabling CPU
energy-efficiency optimizations in the processor.
* Make the driver avoid enabling HWP if EPP is not supported.
* Allow the driver to handle numeric EPP values in the sysfs
interface and fix the setting of EPP via sysfs in the active
mode.
* Eliminate a static checker warning and clean up a kerneldoc
comment.
- Clean up some variable declarations in the powernv cpufreq
driver (Wei Yongjun).
- Fix up the ->enter_s2idle callback definition to cover the case
when it points to the same function as ->idle correctly (Neal
Liu).
- Rearrange and clean up the PSCI cpuidle driver (Ulf Hansson).
- Make the PM core emit "changed" uevent when adding/removing the
"wakeup" sysfs attribute of devices (Abhishek Pandit-Subedi).
- Add a helper macro for declaring PM callbacks and use it in the
MMC jz4740 driver (Paul Cercueil).
- Fix white space in some places in the hibernate code and make the
system-wide PM code use "const char *" where appropriate (Xiang
Chen, Alexey Dobriyan).
- Add one more "unsafe" helper macro to the freezer to cover the NFS
use case (He Zhe).
- Change the language in the generic PM domains framework to use
parent/child terminology and clean up a typo and some comment
fromatting in that code (Kees Cook, Geert Uytterhoeven).
- Update the operating performance points OPP framework (Lukasz
Luba, Andrew-sh.Cheng, Valdis Kletnieks):
* Refactor dev_pm_opp_of_register_em() and update related drivers.
* Add a missing function export.
* Allow disabled OPPs in dev_pm_opp_get_freq().
- Update devfreq core and drivers (Chanwoo Choi, Lukasz Luba, Enric
Balletbo i Serra, Dmitry Osipenko, Kieran Bingham, Marc Zyngier):
* Add support for delayed timers to the devfreq core and make the
Samsung exynos5422-dmc driver use it.
* Unify sysfs interface to use "df-" as a prefix in instance names
consistently.
* Fix devfreq_summary debugfs node indentation.
* Add the rockchip,pmu phandle to the rk3399_dmc driver DT
bindings.
* List Dmitry Osipenko as the Tegra devfreq driver maintainer.
* Fix typos in the core devfreq code.
- Update the pm-graph utility to version 5.7 including a number of
fixes related to suspend-to-idle (Todd Brandt).
- Fix coccicheck errors and warnings in the cpupower utility (Shuah
Khan).
- Replace HTTP links with HTTPs ones in multiple places (Alexander
A. Klimov).
-----BEGIN PGP SIGNATURE-----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=8cUO
-----END PGP SIGNATURE-----
Merge tag 'pm-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The most significant change here is the extension of the Energy Model
to cover non-CPU devices (as well as CPUs) from Lukasz Luba.
There is also some new hardware support (Ice Lake server idle states
table for intel_idle, Sapphire Rapids and Power Limit 4 support in the
RAPL driver), some new functionality in the existing drivers (eg. a
new switch to disable/enable CPU energy-efficiency optimizations in
intel_pstate, delayed timers in devfreq), some assorted fixes (cpufreq
core, intel_pstate, intel_idle) and cleanups (eg. cpuidle-psci,
devfreq), including the elimination of W=1 build warnings from cpufreq
done by Lee Jones.
Specifics:
- Make the Energy Model cover non-CPU devices (Lukasz Luba).
- Add Ice Lake server idle states table to the intel_idle driver and
eliminate a redundant static variable from it (Chen Yu, Rafael
Wysocki).
- Eliminate all W=1 build warnings from cpufreq (Lee Jones).
- Add support for Sapphire Rapids and for Power Limit 4 to the Intel
RAPL power capping driver (Sumeet Pawnikar, Zhang Rui).
- Fix function name in kerneldoc comments in the idle_inject power
capping driver (Yangtao Li).
- Fix locking issues with cpufreq governors and drop a redundant
"weak" function definition from cpufreq (Viresh Kumar).
- Rearrange cpufreq to register non-modular governors at the
core_initcall level and allow the default cpufreq governor to be
specified in the kernel command line (Quentin Perret).
- Extend, fix and clean up the intel_pstate driver (Srinivas
Pandruvada, Rafael Wysocki):
* Add a new sysfs attribute for disabling/enabling CPU
energy-efficiency optimizations in the processor.
* Make the driver avoid enabling HWP if EPP is not supported.
* Allow the driver to handle numeric EPP values in the sysfs
interface and fix the setting of EPP via sysfs in the active
mode.
* Eliminate a static checker warning and clean up a kerneldoc
comment.
- Clean up some variable declarations in the powernv cpufreq driver
(Wei Yongjun).
- Fix up the ->enter_s2idle callback definition to cover the case
when it points to the same function as ->idle correctly (Neal Liu).
- Rearrange and clean up the PSCI cpuidle driver (Ulf Hansson).
- Make the PM core emit "changed" uevent when adding/removing the
"wakeup" sysfs attribute of devices (Abhishek Pandit-Subedi).
- Add a helper macro for declaring PM callbacks and use it in the MMC
jz4740 driver (Paul Cercueil).
- Fix white space in some places in the hibernate code and make the
system-wide PM code use "const char *" where appropriate (Xiang
Chen, Alexey Dobriyan).
- Add one more "unsafe" helper macro to the freezer to cover the NFS
use case (He Zhe).
- Change the language in the generic PM domains framework to use
parent/child terminology and clean up a typo and some comment
fromatting in that code (Kees Cook, Geert Uytterhoeven).
- Update the operating performance points OPP framework (Lukasz Luba,
Andrew-sh.Cheng, Valdis Kletnieks):
* Refactor dev_pm_opp_of_register_em() and update related drivers.
* Add a missing function export.
* Allow disabled OPPs in dev_pm_opp_get_freq().
- Update devfreq core and drivers (Chanwoo Choi, Lukasz Luba, Enric
Balletbo i Serra, Dmitry Osipenko, Kieran Bingham, Marc Zyngier):
* Add support for delayed timers to the devfreq core and make the
Samsung exynos5422-dmc driver use it.
* Unify sysfs interface to use "df-" as a prefix in instance
names consistently.
* Fix devfreq_summary debugfs node indentation.
* Add the rockchip,pmu phandle to the rk3399_dmc driver DT
bindings.
* List Dmitry Osipenko as the Tegra devfreq driver maintainer.
* Fix typos in the core devfreq code.
- Update the pm-graph utility to version 5.7 including a number of
fixes related to suspend-to-idle (Todd Brandt).
- Fix coccicheck errors and warnings in the cpupower utility (Shuah
Khan).
- Replace HTTP links with HTTPs ones in multiple places (Alexander A.
Klimov)"
* tag 'pm-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (71 commits)
cpuidle: ACPI: fix 'return' with no value build warning
cpufreq: intel_pstate: Fix EPP setting via sysfs in active mode
cpufreq: intel_pstate: Rearrange the storing of new EPP values
intel_idle: Customize IceLake server support
PM / devfreq: Fix the wrong end with semicolon
PM / devfreq: Fix indentaion of devfreq_summary debugfs node
PM / devfreq: Clean up the devfreq instance name in sysfs attr
memory: samsung: exynos5422-dmc: Add module param to control IRQ mode
memory: samsung: exynos5422-dmc: Adjust polling interval and uptreshold
memory: samsung: exynos5422-dmc: Use delayed timer as default
PM / devfreq: Add support delayed timer for polling mode
dt-bindings: devfreq: rk3399_dmc: Add rockchip,pmu phandle
PM / devfreq: tegra: Add Dmitry as a maintainer
PM / devfreq: event: Fix trivial spelling
PM / devfreq: rk3399_dmc: Fix kernel oops when rockchip,pmu is absent
cpuidle: change enter_s2idle() prototype
cpuidle: psci: Prevent domain idlestates until consumers are ready
cpuidle: psci: Convert PM domain to platform driver
cpuidle: psci: Fix error path via converting to a platform driver
cpuidle: psci: Fail cpuidle registration if set OSI mode failed
...
-----BEGIN PGP SIGNATURE-----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=abJG
-----END PGP SIGNATURE-----
Merge tag 'for-5.9/block-20200802' of git://git.kernel.dk/linux-block
Pull core block updates from Jens Axboe:
"Good amount of cleanups and tech debt removals in here, and as a
result, the diffstat shows a nice net reduction in code.
- Softirq completion cleanups (Christoph)
- Stop using ->queuedata (Christoph)
- Cleanup bd claiming (Christoph)
- Use check_events, moving away from the legacy media change
(Christoph)
- Use inode i_blkbits consistently (Christoph)
- Remove old unused writeback congestion bits (Christoph)
- Cleanup/unify submission path (Christoph)
- Use bio_uninit consistently, instead of bio_disassociate_blkg
(Christoph)
- sbitmap cleared bits handling (John)
- Request merging blktrace event addition (Jan)
- sysfs add/remove race fixes (Luis)
- blk-mq tag fixes/optimizations (Ming)
- Duplicate words in comments (Randy)
- Flush deferral cleanup (Yufen)
- IO context locking/retry fixes (John)
- struct_size() usage (Gustavo)
- blk-iocost fixes (Chengming)
- blk-cgroup IO stats fixes (Boris)
- Various little fixes"
* tag 'for-5.9/block-20200802' of git://git.kernel.dk/linux-block: (135 commits)
block: blk-timeout: delete duplicated word
block: blk-mq-sched: delete duplicated word
block: blk-mq: delete duplicated word
block: genhd: delete duplicated words
block: elevator: delete duplicated word and fix typos
block: bio: delete duplicated words
block: bfq-iosched: fix duplicated word
iocost_monitor: start from the oldest usage index
iocost: Fix check condition of iocg abs_vdebt
block: Remove callback typedefs for blk_mq_ops
block: Use non _rcu version of list functions for tag_set_list
blk-cgroup: show global disk stats in root cgroup io.stat
blk-cgroup: make iostat functions visible to stat printing
block: improve discard bio alignment in __blkdev_issue_discard()
block: change REQ_OP_ZONE_RESET and REQ_OP_ZONE_RESET_ALL to be odd numbers
block: defer flush request no matter whether we have elevator
block: make blk_timeout_init() static
block: remove retry loop in ioc_release_fn()
block: remove unnecessary ioc nested locking
block: integrate bd_start_claiming into __blkdev_get
...
Use the newly introduced pm_ptr() macro to simplify the code.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Support command queue for mt6779 platform.
a. Add msdc_set_busy_timeout() to calculate emmc write timeout.
b. Connect mtk msdc driver to cqhci driver through
host->cq_host->ops = &msdc_cmdq_ops;
c. msdc_cmdq_irq() will link up with cqchi_irq(). Besides, it provides
more irq error messages like RSPCRCERR/CMDTO/DATACRCERR/DATTMO.
d. Select kernel config MMC_CQHCI for MMC_MTK
Signed-off-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Acked-by: Yong Mao <yong.mao@mediatek.com>
Link: https://lore.kernel.org/r/1595205759-5825-4-git-send-email-chun-hung.wu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Extract msdc timeout api common part to have
better code architecture and avoid redundant code.
Signed-off-by: Chun-Hung Wu <chun-hung.wu@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/1595205759-5825-3-git-send-email-chun-hung.wu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To fix support for the O2 host controller Seabird1, set the quirk
SDHCI_QUIRK2_PRESET_VALUE_BROKEN and the capability bit MMC_CAP2_NO_SDIO.
Moreover, assign the ->get_cd() callback.
Signed-off-by: Shirley Her <shirley.her@bayhubtech.com>
Link: https://lore.kernel.org/r/20200721011733.8416-1-shirley.her@bayhubtech.com
[Ulf: Updated the commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers using legacy PM have to manage PCI states and device's PM states
themselves. They also need to take care of configuration registers.
With improved and powerful support of generic PM, PCI Core takes care of
above mentioned, device-independent, jobs.
This driver makes use of PCI helper functions like
pci_save/restore_state(), pci_enable/disable_device(),
pci_enable_wake() and pci_set_power_state() and to do required operations.
In generic mode, they are no longer needed.
Change function parameter in both .suspend() and .resume() to
"struct device*" type. Use dev_get_drvdata() to get drv data.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Link: https://lore.kernel.org/r/20200720142603.577323-1-vaibhavgupta40@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As commit ef6b75671b ("mmc: sdhci-cadence: send tune request twice to
work around errata") stated, this IP has an errata. This commit applies
the second workaround for the SD mode.
Due to the errata, it is not possible to use the hardware tuning provided
by SDHCI_HOST_CONTROL2.
Use the software-controlled tuning like the eMMC mode.
Set sdhci_host_ops::platform_execute_tuning instead of overriding
mmc_host_ops::execute_tuning.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Link: https://lore.kernel.org/r/20200720061141.172944-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The initial code that was adding delays was doing a cast over undefined
memory. This meant that the delays would be all gibberish.
This change, allocates all delays on the stack, and assigns them from the
ZynqMP & Versal macros/phase-list. And then finally copies them over the
common iclk_phase & oclk_phase variables.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1594753953-62980-1-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Smatch complains that "ret" can be used without being initialized.
drivers/mmc/host/sdhci.c
4383 if (!IS_ERR(mmc->supply.vqmmc)) {
4384 if (enable_vqmmc) {
^^^^^^^^^^^^
4385 ret = regulator_enable(mmc->supply.vqmmc);
^^^^^
4386 host->sdhci_core_to_disable_vqmmc = !ret;
4387 }
"ret" is only initialized when "enable_vqmmc" is true.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200714141410.GB314989@mwanda
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
The commit 5a36d6bcdf ("mmc: core: Add DT-bindings for
MMC_CAP2_FULL_PWR_CYCLE") added the "full-pwr-cycle" property which
is possible to perform a full power cycle of the card at any time.
However, some environment (like r8a77951-salvator-xs) is possible
to perform a full power cycle of the card in suspend via firmware
(PSCI on arm-trusted-firmware). So, in worst case, since we are
not doing a graceful shutdown of the eMMC device (just cut VCCQ
while the eMMC is "sleeping") in suspend, it could lead to internal
data corruptions. So, add MMC_CAP2_FULL_PWR_CYCLE_IN_SUSPEND
to do a graceful shutdown which issues Power Off notification
before entering system suspend.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1594123122-13156-3-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since ACPI_PTR() is used to NULLify the value when !CONFIG_ACPI,
'struct sdhci_iproc_acpi_ids' becomes defined but unused.
Fixes the following W=1 kernel build warning:
mmc/host/sdhci-iproc.c:297:36: warning: ‘sdhci_iproc_acpi_ids’ defined but not used [-Wunused-const-variable=]
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Link: https://lore.kernel.org/r/20200707064701.GC3500@dell
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The variable 'found' is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200706163031.503431-1-colin.king@canonical.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cqhci_host_alloc_tdl()'s function header is the only one in
kerneldoc format. Which seems odd as it's not part of an
external API and isn't referenced anywhere else. Seeing as
there has also been no attempt to describe the expected
function arguments either, we're going to assume that this is
not actually a bona fide kerneldoc use-case.
Fixes the following W=1 kernel build warning:
drivers/mmc/host/cqhci.c:163: warning: Function parameter or member 'cq_host' not described in 'cqhci_host_alloc_tdl'
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ritesh Harjani <riteshh@codeaurora.org>
Cc: Asutosh Das <asutoshd@codeaurora.org>
Cc: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200701124702.908713-15-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
__sdhci_msm_set_clock()'s function header is the only one in
kerneldoc format. Which seems odd as it's not part of an
external API and isn't referenced anywhere else. Seeing as
there has also been no attempt to describe the expected
function arguments either, we're going to assume that this is
not actually a bona fide kerneldoc use-case.
Fixes the following W=1 kernel build warnings:
drivers/mmc/host/sdhci-msm.c:1595: warning: Function parameter or member 'host' not described in '__sdhci_msm_set_clock'
drivers/mmc/host/sdhci-msm.c:1595: warning: Function parameter or member 'clock' not described in '__sdhci_msm_set_clock'
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-14-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Kerneldoc expects arg descriptions to be in the format '@.*: '. If either
the '@' or the ':' is omitted then kerneldoc complains that the description
is missing. Add the missing ':' here and provide a new description for
'value'.
Fixes the following kernel build W=1 warnings:
drivers/mmc/host/sdhci-of-arasan.c:1394: warning: Function parameter or member 'host' not described in 'sdhci_arasan_update_support64b'
drivers/mmc/host/sdhci-of-arasan.c:1394: warning: Function parameter or member 'value' not described in 'sdhci_arasan_update_support64b'
drivers/mmc/host/sdhci-msm.c:1887:6: warning: no previous prototype for ‘sdhci_msm_dump_vendor_regs’ [-Wmissing-prototypes]
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Xiaobo Xie <X.Xie@freescale.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Soeren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-12-lee.jones@linaro.org
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Seeing as sd_wait_data_idle() returns void and only a very specific
read value is checked, there doesn't seem to be a good reason to
check the return value of rtsx_pci_read_register(). So remove
the assignment and definition of 'err'.
Squashes the following W=1 kernel build warning:
drivers/mmc/host/rtsx_usb_sdmmc.c: In function ‘sd_wait_data_idle’:
drivers/mmc/host/rtsx_usb_sdmmc.c:657:6: warning: variable ‘err’ set but not used [-Wunused-but-set-variable]
657 | int err, i;
| ^~~
Cc: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-11-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Seeing as sd_wait_data_idle() returns void and only a very specific
read value is checked, there doesn't seem to be a good reason to
check the return value of rtsx_pci_read_register(). So remove
the assignment and definition of 'err'.
Squashes the following W=1 kernel build warning:
drivers/mmc/host/rtsx_pci_sdmmc.c: In function ‘sd_wait_data_idle’:
drivers/mmc/host/rtsx_pci_sdmmc.c:678:6: warning: variable ‘err’ set but not used [-Wunused-but-set-variable]
678 | int err, i;
| ^~~
Cc: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-10-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Provide missing documentation for dw_mci_exynos_suspend_noirq() and
dw_mci_exynos_resume_noirq() function headers.
Fixes the following W=1 kernel build warnings:
drivers/mmc/host/dw_mmc-exynos.c:184: warning: Function parameter or member 'dev' not described in 'dw_mci_exynos_suspend_noirq'
drivers/mmc/host/dw_mmc-exynos.c:200: warning: Function parameter or member 'dev' not described in 'dw_mci_exynos_resume_noirq'
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20200701124702.908713-9-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Correcting this misspelling squashes the following W=1 build warning(s):
mmc/core/queue.c:212: warning: Function parameter or member 'mq' not described in '__mmc_init_request'
mmc/core/queue.c:212: warning: Excess function parameter 'q' description in '__mmc_init_request'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-8-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'sg_len' and 'dma_conf' are missing correct kerneldoc documentation and
'buf_phys_addr' was misspelled. Correcting these issues fixes the
following W=1 kernel build issues:
mmc/host/atmel-mci.c:352: warning: Function parameter or member 'sg_len' not described in 'atmel_mci'
mmc/host/atmel-mci.c:352: warning: Function parameter or member 'buf_phys_addr' not described in 'atmel_mci'
mmc/host/atmel-mci.c:352: warning: Function parameter or member 'dma_conf' not described in 'atmel_mci'
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-7-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No other function in the file is documented using kerneldoc and no
effort to document the function arguments have been made. It's a
bit of an oddity to say the least. Let's downgrade it from
kerneldoc to a standard comment block instead.
Fixes the following W=1 kernel build warning:
drivers/mmc/host/mtk-sd.c:1030: warning: Function parameter or member 'host' not described in 'msdc_recheck_sdio_irq'
Cc: Chaotian Jing <chaotian.jing@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20200701124702.908713-6-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Describe properties; ext_cd_irq, clk_rates and no_divider (x2).
Squashes the following W=1 kernel build warnings:
drivers/mmc/host/sdhci-s3c.c:126: warning: Function parameter or member 'ext_cd_irq' not described in 'sdhci_s3c'
drivers/mmc/host/sdhci-s3c.c:126: warning: Function parameter or member 'clk_rates' not described in 'sdhci_s3c'
drivers/mmc/host/sdhci-s3c.c:126: warning: Function parameter or member 'no_divider' not described in 'sdhci_s3c'
drivers/mmc/host/sdhci-s3c.c:139: warning: Function parameter or member 'no_divider' not described in 'sdhci_s3c_drv_data'
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20200701124702.908713-5-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remainder of the kerneldoc descriptions look present and correct.
Fixes the following W=1 kernel build warnings:
drivers/mmc/core/regulator.c:178: warning: Function parameter or member 'mmc' not described in 'mmc_regulator_set_vqmmc'
drivers/mmc/core/regulator.c:178: warning: Function parameter or member 'ios' not described in 'mmc_regulator_set_vqmmc'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-4-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add missing kerneldoc entry for sdio_set_host_pm_flags()'s 'flag'
function argument.
Fixes the following W=1 kernel build warning:
kernel/drivers/mmc/core/sdio_io.c:722: warning: Function parameter or member 'flags' not described in 'sdio_set_host_pm_flags'
Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-3-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Not all source files which include quirks.h make use of the all of
the available fixup information. When this happens the compiler
complains that some constant variables are defined by never used.
We can fix this by telling the compiler that this intentional by
simply marking them as __maybe_unused.
Fixes the following W=1 kernel build warnings:
In file included from drivers/mmc/core/sdio.c:22:
drivers/mmc/core/quirks.h:105:31: warning: ‘mmc_ext_csd_fixups’ defined but not used [-Wunused-const-variable=]
105 | static const struct mmc_fixup mmc_ext_csd_fixups[] = {
| ^~~~~~~~~~~~~~~~~~
drivers/mmc/core/quirks.h:17:31: warning: ‘mmc_blk_fixups’ defined but not used [-Wunused-const-variable=]
17 | static const struct mmc_fixup mmc_blk_fixups[] = {
| ^~~~~~~~~~~~~~
In file included from drivers/mmc/core/mmc.c:25:
drivers/mmc/core/quirks.h:123:31: warning: ‘sdio_fixup_methods’ defined but not used [-Wunused-const-variable=]
123 | static const struct mmc_fixup sdio_fixup_methods[] = {
| ^~~~~~~~~~~~~~~~~~
drivers/mmc/core/quirks.h:17:31: warning: ‘mmc_blk_fixups’ defined but not used [-Wunused-const-variable=]
17 | static const struct mmc_fixup mmc_blk_fixups[] = {
| ^~~~~~~~~~~~~~
Cc: Andrei Warkentin <andreiw@motorola.com>
Cc: Martin Mares <mj@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-2-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix sparse build warning:
drivers/mmc/host/sdhci-msm.c:1888:6: warning:
symbol 'sdhci_msm_dump_vendor_regs' was not declared. Should it be static?
Signed-off-by: Hulk Robot <hulkci@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200702020347.77214-1-weiyongjun1@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If this controller doesn't issue interrupt for response of command,
this driver lacks to call dma_unmap_sg(). So, fix the issue by
using end() of struct tmio_mmc_dma_ops.
Reported-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Fixes: 2a68ea7896 ("mmc: renesas-sdhi: add support for R-Car Gen3 SDHI DMAC")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1590044466-28372-4-git-send-email-yoshihiro.shimoda.uh@renesas.com
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To add end() operation in the future, clean the code of
renesas_sdhi_internal_dmac_complete_tasklet_fn(). No behavior change.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1590044466-28372-3-git-send-email-yoshihiro.shimoda.uh@renesas.com
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Related drivers like renesas_sdhi_internal_dmac are possible
to lack dma unmaping in error cases (for example response timeout).
Since tmio_mmc_finish_request() will be always called in any case,
to fix the issue, add end operation into struct tmio_mmc_dma_ops and
call the operation in tmio_mmc_finish_request() to call dma_ummap API
by the related drivers correctly.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1590044466-28372-2-git-send-email-yoshihiro.shimoda.uh@renesas.com
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On qcom SD host controllers voltage switching be done after the HW
is ready for it. The HW informs its readiness through power irq.
The voltage switching should happen only then.
Use the internal voltage switching and then control the voltage
switching using power irq.
IO-bus supply of eMMC would be kept always-on. So set the load
for this supply to configure it in LPM when eMMC is suspend state
and in HPM when eMMC is active.
Co-developed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Co-developed-by: Vijay Viswanath <vviswana@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Co-developed-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1592919288-1020-4-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set the default power mode, MMC_POWER_UNDEFINED, in mmc_alloc_host() rather
than in mmc_start_host(). This enables host drivers to make use of the
initial state during ->probe().
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org> Link:
https://lore.kernel.org/r/1592919288-1020-3-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If vendor platform drivers are controlling whole logic of voltage
switching, then sdhci driver no need control vqmmc regulator.
So skip enabling/disable vqmmc from SDHC driver.
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1592919288-1020-2-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
HS400/HS200/eMMC HS doesn't have Preset Value register.
Hence, sdhci_set_ios function overrides the value set by fmw to
SDHCI_CTRL_DRV_TYPE_B.
This patch sets drv_type to MMC_SET_DRIVER_TYPE_A
so that host_control2 register gets updated with the required
strength value.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200623133347.4598-1-akshu.agrawal@amd.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
USDHC of i.MX has internal IC debug register, which record the IC
logical status. So dump these logical status in error condition,
this can help analyzing issue.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1592985830-13038-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In current code logic, when work in SDR12/SDR25 mode, the final clock
rate is incorrect, just the legancy 400KHz, because the
card->sw_caps.sd3_bus_mode do not has the flag SD_MODE_UHS_SDR12 or
SD_MODE_UHS_SDR25. Besides, SDIO_SPEED_SDR12 is actually value 0, and
every mode need to config the timing and clock rate, so remove the
‘if’ operator.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Tested-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/1592813959-5914-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for writing new clkbuf_sel property for the J721e 4 bit IP.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Link: https://lore.kernel.org/r/20200619125801.9530-7-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For speed modes where DLL is not enabled write to TXDLYCLK to enable
transmitter delay chain mode.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200619125801.9530-6-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The clock > CLOCK_TOO_SLOW_HZ condition gating phy configuration
is only required because dll should not be enabled at too low a
clock frequency or too low timing. Make sure that this condition
only gates dll enablement.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200619125801.9530-5-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add Support for AM65x PG2.0. Use the SoC bus framework to fixup
the driver data and skip do DLL calibration if the revision is 1.0
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200619125801.9530-4-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Not all controllers need calibration for the PHY DLL. Add a DLL_CALIB flag
to indicate the same.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200619125801.9530-3-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
"K" stands for "kelvin".
While at it, make the spacing before units consistent.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200618080321.16678-1-geert+renesas@glider.be
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds datactrl_mask_sdio for sdmmc revisions.
sdmmc revisions used same bit of previous ST variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200611132839.4515-1-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These functions do not check the return value of devm_clk_register():
- sdhci_arasan_register_sdcardclk()
- sdhci_arasan_register_sampleclk()
Therefore, add the missed checks to fix them.
Fixes: c390f2110a ("mmc: sdhci-of-arasan: Add ability to export card clock")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200608162226.3259186-1-hslester96@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 6b5eda369a ("sdio: put active devices into 1-bit mode during
suspend") disabled 4-bit mode during system suspend. After this patch,
commit 7310ece86a ("mmc: implement SD-combo (IO+mem) support") used
new sdio_enable_4bit_bus() instead of sdio_enable_wide() to support
SD-combo cards, also for card resume. However, no corresponding support
added during suspend. That is not correct. Let's fix it.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20200609081431.6376-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the card type is SD combo(MMC_TYPE_SD_COMBO) and the memory part does
not support wider bus(SD_SCR_BUS_WIDTH_4), nothing will be done except
return 0. However, we should check whether IO part support wider bus or
not. We should use available IO ability if supported.
In addition, there's a duplicated check to MMC_CAP_4_BIT_DATA since
sdio_enable_wide() will include that check. And we can also save one
call site to sdio_enable_wide() after this change.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20200608103009.5000-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We should return any possible error returned by mmc_io_rw_direct()
rather than only -EIO in sdio_disable_func() failure path.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200604100102.13572-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Interconnect bandwidth scaling support is now added as a
part of OPP. So, make sure interconnect driver is ready
before handling interconnect scaling.
Signed-off-by: Pradeep P V K <ppvk@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1591691846-7578-2-git-send-email-ppvk@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The approach to allow userspace ~5s to consume the uevent, which is
triggered when a new card is inserted/initialized, currently requires the
mmc host to support system wakeup.
This is unnecessary limiting, especially for an mmc host that relies on a
GPIO IRQ for card detect. More precisely, the mmc host may not support
system wakeup for its corresponding struct device, while the GPIO IRQ still
could be configured as a wakeup IRQ via enable_irq_wake().
To support all various cases, let's simply drop the need for the wakeup
support. Instead let's always register a wakeup source and activate it for
all card detect IRQs by calling __pm_wakeup_event().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200529102341.12529-1-ulf.hansson@linaro.org
When calculating the clock divider, start dividing at 2 instead of 1.
The divider is divided by two at the end of the calculation, so starting
at 1 may result in a divider of 0, which shouldn't happen.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200709195706.12741-3-eajames@linux.ibm.com
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to support new chip rts5228, the definitions of some internal
registers and workflow have to be modified.
Added rts5228.c rts5228.h for independent functions of the new chip rts5228
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/20200706070259.32565-1-ricky_wu@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mmc driver doesn't support event notifications, which means
that check_disk_change is a no-op.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
During DLL initialization, the DLL_CONFIG register value would be
updated with the value supplied from the device-tree.
Override this register only if a valid value is supplied.
Fixes: 03591160ca ("mmc: sdhci-msm: Read and use DLL Config property from device tree file")
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1594213888-2780-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move the call to blk_should_fake_timeout out of blk_mq_complete_request
and into the drivers, skipping call sites that are obvious error
handlers, and remove the now superflous blk_mq_force_complete_rq helper.
This ensures we don't keep injecting errors into completions that just
terminate the Linux request after the hardware has been reset or the
command has been aborted.
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The actual max_segs computation leads to failure while using the broadcom
sdio brcmfmac/bcmsdh driver, since the driver tries to make usage of
scatter gather.
But with the dram-access-quirk we use a 1,5K SRAM bounce buffer, and the
max_segs current value of 3 leads to max transfers to 4,5k, which doesn't
work.
This patch sets max_segs to 1 to better describe the hardware limitation,
and fix the SDIO functionality with the brcmfmac/bcmsdh driver on Amlogic
G12A/G12B SoCs on boards like SEI510 or Khadas VIM3.
Reported-by: Art Nikpal <art@khadas.com>
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Fixes: acdc8e71d9 ("mmc: meson-gx: add dram-access-quirk")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200608084458.32014-1-narmstrong@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Because SCHED_FIFO is a broken scheduler model (see previous patches)
take away the priority field, the kernel can't possibly make an
informed decision.
In this case, use fifo_low, because it only cares about being above
SCHED_NORMAL. Effectively no change in behaviour.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
function that isn't used anymore. Otherwise the main new thing for the common
clk framework is that it is selectable in the Kconfig language now. Hopefully
this will let clk drivers and clk consumers be testable on more than the
architectures that support the clk framework. The goal is to introduce some
Kunit tests for the framework.
Outside of the core framework we have the usual set of various driver updates
and non-critical fixes. The dirstat shows that the new Baikal-T1 driver is the
largest addition this time around in terms of lines of code. After that the x86
(Intel), Qualcomm, and Mediatek drivers introduce many lines to support new or
upcoming SoCs. After that the dirstat shows the usual suspects working on their
SoC support by fixing minor bugs, correcting data and converting some of their
DT bindings to YAML.
Core:
- Allow the COMMON_CLK config to be selectable
New Drivers:
- Clk driver for Baikal-T1 SoCs
- Mediatek MT6765 clock support
- Support for Intel Agilex clks
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for the new Renesas RZ/G1H (R8A7742) SoC
- Add support for Qualcomm's MSM8939 Generic Clock Controller
Updates:
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- A single minor rounding fix for the legacy Allwinner clock support
- A few patches from Abel Vesa as preparation of adding audiomix clock support
on i.MX
- A couple of cleanups from Anson Huang for i.MX clk-sscg-pll and clk-pllv3
drivers
- Drop dependency on ARM64 for i.MX8M clock driver, to support aarch32 mode on
aarch64 hardware
- A series from Peng Fan to improve i.MX8M clock drivers, using composite
clock for core and bus clk slice
- Set a better parent clock for flexcan on i.MX6UL to support CiA102 defined
bit rates
- A couple changes for EMC frequency scaling on Tegra210
- Support for CPU frequency scaling on Tegra20/Tegra30
- New clk gate for CSI test pattern generator on Tegra210
- Regression fixes for Samsung exynos542x and exynos5433 SoCs
- Use of fallthrough; attribute for Samsung s3c24xx
- Updates and fixup HDMI and video clocks on Meson8b
- Fixup reset polarity on Meson8b
- Fix GPU glitch free mux switch on Meson gx and g12
- A minor fix for the currently unused suspend/resume handling on Renesas RZ/A1 and RZ/A2
- Two more conversions of Renesas DT bindings to json-schema
- Add support for the USB 2.0 clock selector on Renesas R-Car M3-W+
-----BEGIN PGP SIGNATURE-----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=nuG5
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time around we have four lines of diff in the core framework,
removing a function that isn't used anymore. Otherwise the main new
thing for the common clk framework is that it is selectable in the
Kconfig language now. Hopefully this will let clk drivers and clk
consumers be testable on more than the architectures that support the
clk framework. The goal is to introduce some Kunit tests for the
framework.
Outside of the core framework we have the usual set of various driver
updates and non-critical fixes. The dirstat shows that the new
Baikal-T1 driver is the largest addition this time around in terms of
lines of code. After that the x86 (Intel), Qualcomm, and Mediatek
drivers introduce many lines to support new or upcoming SoCs. After
that the dirstat shows the usual suspects working on their SoC support
by fixing minor bugs, correcting data and converting some of their DT
bindings to YAML.
Core:
- Allow the COMMON_CLK config to be selectable
New Drivers:
- Clk driver for Baikal-T1 SoCs
- Mediatek MT6765 clock support
- Support for Intel Agilex clks
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for the new Renesas RZ/G1H (R8A7742) SoC
- Add support for Qualcomm's MSM8939 Generic Clock Controller
Updates:
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- A single minor rounding fix for the legacy Allwinner clock support
- A few patches from Abel Vesa as preparation of adding audiomix
clock support on i.MX
- A couple of cleanups from Anson Huang for i.MX clk-sscg-pll and
clk-pllv3 drivers
- Drop dependency on ARM64 for i.MX8M clock driver, to support
aarch32 mode on aarch64 hardware
- A series from Peng Fan to improve i.MX8M clock drivers, using
composite clock for core and bus clk slice
- Set a better parent clock for flexcan on i.MX6UL to support CiA102
defined bit rates
- A couple changes for EMC frequency scaling on Tegra210
- Support for CPU frequency scaling on Tegra20/Tegra30
- New clk gate for CSI test pattern generator on Tegra210
- Regression fixes for Samsung exynos542x and exynos5433 SoCs
- Use of fallthrough; attribute for Samsung s3c24xx
- Updates and fixup HDMI and video clocks on Meson8b
- Fixup reset polarity on Meson8b
- Fix GPU glitch free mux switch on Meson gx and g12
- A minor fix for the currently unused suspend/resume handling on
Renesas RZ/A1 and RZ/A2
- Two more conversions of Renesas DT bindings to json-schema
- Add support for the USB 2.0 clock selector on Renesas R-Car M3-W+"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (155 commits)
clk: mediatek: Remove ifr{0,1}_cfg_regs structures
clk: baikal-t1: remove redundant assignment to variable 'divider'
clk: baikal-t1: fix spelling mistake "Uncompatible" -> "Incompatible"
dt-bindings: clock: Add a missing include to MMP Audio Clock binding
dt: Add bindings for IDT VersaClock 5P49V5925
clk: vc5: Add support for IDT VersaClock 5P49V6965
clk: Add Baikal-T1 CCU Dividers driver
clk: Add Baikal-T1 CCU PLLs driver
dt-bindings: clk: Add Baikal-T1 CCU Dividers binding
dt-bindings: clk: Add Baikal-T1 CCU PLLs binding
clk: mediatek: assign the initial value to clk_init_data of mtk_mux
clk: mediatek: Add MT6765 clock support
clk: mediatek: add mt6765 clock IDs
dt-bindings: clock: mediatek: document clk bindings vcodecsys for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings mipi0a for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings for Mediatek MT6765 SoC
CLK: HSDK: CGU: add support for 148.5MHz clock
CLK: HSDK: CGU: support PLL bypassing
CLK: HSDK: CGU: check if PLL is bypassed first
clk: clk-si5341: Add support for the Si5345 series
...
Here is the large set of char/misc driver patches for 5.8-rc1
Included in here are:
- habanalabs driver updates, loads
- mhi bus driver updates
- extcon driver updates
- clk driver updates (approved by the clock maintainer)
- firmware driver updates
- fpga driver updates
- gnss driver updates
- coresight driver updates
- interconnect driver updates
- parport driver updates (it's still alive!)
- nvmem driver updates
- soundwire driver updates
- visorbus driver updates
- w1 driver updates
- various misc driver updates
In short, loads of different driver subsystem updates along with the
drivers as well.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXtzkHw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yldOwCgus/DgpnI1UL4z+NdBxJrAXtkPmgAn2sgTUea
i5RblCmcVMqvHaGtYkY+
=tScN
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char/misc driver patches for 5.8-rc1
Included in here are:
- habanalabs driver updates, loads
- mhi bus driver updates
- extcon driver updates
- clk driver updates (approved by the clock maintainer)
- firmware driver updates
- fpga driver updates
- gnss driver updates
- coresight driver updates
- interconnect driver updates
- parport driver updates (it's still alive!)
- nvmem driver updates
- soundwire driver updates
- visorbus driver updates
- w1 driver updates
- various misc driver updates
In short, loads of different driver subsystem updates along with the
drivers as well.
All have been in linux-next for a while with no reported issues"
* tag 'char-misc-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (233 commits)
habanalabs: correctly cast u64 to void*
habanalabs: initialize variable to default value
extcon: arizona: Fix runtime PM imbalance on error
extcon: max14577: Add proper dt-compatible strings
extcon: adc-jack: Fix an error handling path in 'adc_jack_probe()'
extcon: remove redundant assignment to variable idx
w1: omap-hdq: print dev_err if irq flags are not cleared
w1: omap-hdq: fix interrupt handling which did show spurious timeouts
w1: omap-hdq: fix return value to be -1 if there is a timeout
w1: omap-hdq: cleanup to add missing newline for some dev_dbg
/dev/mem: Revoke mappings when a driver claims the region
misc: xilinx-sdfec: convert get_user_pages() --> pin_user_pages()
misc: xilinx-sdfec: cleanup return value in xsdfec_table_write()
misc: xilinx-sdfec: improve get_user_pages_fast() error handling
nvmem: qfprom: remove incorrect write support
habanalabs: handle MMU cache invalidation timeout
habanalabs: don't allow hard reset with open processes
habanalabs: GAUDI does not support soft-reset
habanalabs: add print for soft reset due to event
habanalabs: improve MMU cache invalidation code
...
Clear tuning_done flag while executing tuning to ensure vendor
specific HS400 settings are applied properly when the controller
is re-initialized in HS400 mode.
Without this, re-initialization of the qcom SDHC in HS400 mode fails
while resuming the driver from runtime-suspend or system-suspend.
Fixes: ff06ce4178 ("mmc: sdhci-msm: Add HS400 platform support")
Cc: stable@vger.kernel.org
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1590678838-18099-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Device/vendor ids from Common CIS (Card Information Structure) may be
different as device/vendor ids from CIS on particular SDIO function.
Kernel currently exports only device/vendor ids from SDIO functions and not
"main" device/vendor ids from Common CIS.
This patch exports "main" device/vendor ids for SDIO and SD combo cards at
top level mmc device in sysfs hierarchy.
Userspace can use e.g. udev rules to correctly match whole SDIO card based
on Common CIS device/vendor id and not only one particular SDIO function.
Having this information in userspace also helps developers to debug whole
SDIO card as e.g. kernel mmc quirks use device/vendor ids from Common CIS
and not from particular SDIO function. Also it allows to write userspace
applications which list all connected SDIO cards based on CIS ids.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Link: https://lore.kernel.org/r/20200527110858.17504-2-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDIO non-combo cards are not handled by mmc_block driver and do not have
accessible CID register which is used for MMC_NAME= construction.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Link: https://lore.kernel.org/r/20200527110858.17504-1-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When enabling calibration at reset, the CALCR register was completely
rewritten. This may cause certain bits being deleted unintentedly.
Fix by issuing a read-modify-write operation.
Fixes: 727d836a37 ("mmc: sdhci-of-at91: add DT property to enable calibration on full reset")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20200527105659.142560-1-eugen.hristev@microchip.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In current code, we add 1ms dealy after each tuning command for standard
tuning method. Adding this 1ms dealy is because USDHC default check the
CMD CRC and DATA line. If detect the CMD CRC, USDHC standard tuning
IC logic do not wait for the tuning data sending out by the card, trigger
the buffer read ready interrupt immediately, and step to next cycle. So
when next time the new tuning command send out by USDHC, card may still
not send out the tuning data of the upper command，then some eMMC cards
may stuck, can't response to any command, block the whole tuning procedure.
If do not check the CMD CRC for tuning, then do not has this issue. USDHC
will wait for the tuning data of each tuning command and check them. If the
tuning data pass the check, it also means the CMD line also okay for tuning.
So this patch disable the CMD CRC check for tuning, save some time for the
whole tuning procedure.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/1590488522-9292-2-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According the RM, the bit[6~0] of register ESDHC_TUNING_CTRL is
TUNING_START_TAP, bit[7] of this register is to disable the command
CRC check for standard tuning. So fix it here.
Fixes: d87fc96636 ("mmc: sdhci-esdhc-imx: support setting tuning start point")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/1590488522-9292-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When use the specific GPIO to detect the card insert/remove, we can
also add the GPIO as a wakeup source. When system suspend, insert or
remove the card can wakeup the system.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/1590547175-15070-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Turning on CONFIG_DMA_API_DEBUG_SG results in the following warning:
WARNING: CPU: 1 PID: 85 at kernel/dma/debug.c:1302
debug_dma_map_sg+0x2a0/0x3cc mmci-pl18x 58005000.sdmmc: DMA-API: mapping sg
segment longer than device claims to support [len=126976] [max=65536]
dma api debug checks and compares the segment size to dma_get_max_seg_size
(dev->dma_parms->max_segment_size), the sdmmc variant has an internal DMA
and should define its max_segment_size constraint to avoid this warning.
This Patch defines the dev->dma_parms->max_segment_size with the constraint
already set for mmc core (host->mmc->max_seg_size).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200526155103.12514-3-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Turning on CONFIG_DMA_API_DEBUG_SG results in the following warning:
WARNING: CPU: 1 PID: 20 at kernel/dma/debug.c:500 add_dma_entry+0x16c/0x17c
DMA-API: exceeded 7 overlapping mappings of cacheline 0x031d2645
Modules linked in:
CPU: 1 PID: 20 Comm: kworker/1:1 Not tainted 5.5.0-rc2-00021-gdeda30999c2b-dirty #49
Hardware name: STM32 (Device Tree Support)
Workqueue: events_freezable mmc_rescan
[<c03138c0>] (unwind_backtrace) from [<c030d760>] (show_stack+0x10/0x14)
[<c030d760>] (show_stack) from [<c0f2eb28>] (dump_stack+0xc0/0xd4)
[<c0f2eb28>] (dump_stack) from [<c034a14c>] (__warn+0xd0/0xf8)
[<c034a14c>] (__warn) from [<c034a530>] (warn_slowpath_fmt+0x94/0xb8)
[<c034a530>] (warn_slowpath_fmt) from [<c03bca0c>] (add_dma_entry+0x16c/0x17c)
[<c03bca0c>] (add_dma_entry) from [<c03bdf54>] (debug_dma_map_sg+0xe4/0x3d4)
[<c03bdf54>] (debug_dma_map_sg) from [<c0d09244>] (sdmmc_idma_prep_data+0x94/0xf8)
[<c0d09244>] (sdmmc_idma_prep_data) from [<c0d05a2c>] (mmci_prep_data+0x2c/0xb0)
[<c0d05a2c>] (mmci_prep_data) from [<c0d073ec>] (mmci_start_data+0x134/0x2f0)
[<c0d073ec>] (mmci_start_data) from [<c0d078d0>] (mmci_request+0xe8/0x154)
[<c0d078d0>] (mmci_request) from [<c0cecb44>] (mmc_start_request+0x94/0xbc)
DMA api debug brings to light leaking dma-mappings, dma_map_sg and
dma_unmap_sg are not correctly balanced.
If a request is prepared, the dma_map/unmap are done in asynchronous call
pre_req (prep_data) and post_req (unprep_data). In this case the
dma-mapping is right balanced.
But if the request was not prepared, the data->host_cookie is define to
zero and the dma_map/unmap must be done in the request. The dma_map is
called by mmci_dma_start (prep_data), but there is no dma_unmap in this
case.
This patch adds dma_unmap_sg when the dma is finalized and the data cookie
is zero (request not prepared).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200526155103.12514-2-ludovic.barre@st.com
Fixes: 46b723dd86 ("mmc: mmci: add stm32 sdmmc variant")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Intel Keem Bay SoC eMMC/SD/SDIO controller is based on
Arasan SD 3.0 / eMMC 5.1 host controller IP.
However, it does not support 64-bit access as its AXI interface
has 32-bit address ports.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200526062758.17642-3-wan.ahmad.zainie.wan.mohamad@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Accordingly to Cadence documentation, PHY write procedure is:
1. Software sets the PHY Register Address (HRS04[5:0]) and the
PHY Write Data (HRS04[15:8]) fields.
2. Software sets the PHY Write Transaction Request (HRS04[24]) field to 1.
3. Software waits as the PHY Write Transaction Acknowledge (HRS04[26])
field is equal to 0.
4. Hardware performs the write transaction to PHY register where
HRS04[15:8] is a data written to register under HRS04[5:0] address.
5. Hardware sets the PHY Transaction Acknowledge (HRS04[26]) to 1 when
transaction is completed.
6. Software clears the PHY Write Transaction Request (HRS04[24]) to 1
after noticing that the PHY Write Transaction Acknowledge (HRS04[26])
field is equal to 1.
7. Software waits for the PHY Acknowledge Register (HRS04[26]) field is
equal to 0.
Add missing steps 3 and 7. Lack of these steps causes
integrity errors detested by hardware.
Signed-off-by: Vladimir Kondratiev <vladimir.kondratiev@intel.com>
Link: https://lore.kernel.org/r/20200525074053.7309-1-vladimir.kondratiev@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Marvell SDIO device ID 0x9134 is used in SDIO Common CIS (Card Information
Structure) and not in SDIO wlan function (with ID 1). SDIO Common CIS is
accessed by function ID 0.
So change this misleading macro name to SDIO_DEVICE_ID_MARVELL_8887_F0 as
it does not refer to wlan function. It refers to function 0.
Wlan module on this SDIO card is available at function ID 1 and is
identified by different SDIO device ID 0x9135. Kernel quirks for SDIO
devices are matched against device ID from SDIO Common CIS. Therefore
device ID used in quirk is correct, just has misleading name.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-2-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eSDHC HS400 timing requires many specific registers setting,
unlike other speed modes which need to set only host controller 2
register. When driver needs to downgrade HS400 mode to other speed
mode, the controller have to exit HS400 timing properly first.
This patch is to support the procedure of HS400 exiting at the
beginning of esdhc_set_uhs_signaling.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200522031256.856-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement dump_vendor_registers host operation to print the
vendor specific registers in addition to standard SDHC
register during error conditions.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1590139950-7288-9-git-send-email-sartgarg@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Introduce new sdhci ops to dump vendor specific registers in the
sdhci_dumpregs during error.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1590139950-7288-8-git-send-email-sartgarg@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Certain platforms require different settings in the
SDCC_HC_REG_DLL_CONFIG register. This setting can change from platform
to platform. So the driver should check whether a particular platform
require a different setting by reading the DT file and use it.
Also use msm_cm_dll_set_freq only when DLL not supplied.
Signed-off-by: Bao D. Nguyen <nguyenb@codeaurora.org>
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1590139950-7288-7-git-send-email-sartgarg@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Certain platforms require different settings in the
SDCC_HC_REG_DDR_CONFIG register. This setting can change from platform
to platform. So the driver should check whether a particular platform
require a different setting by reading the device tree file and use it.
Signed-off-by: Bao D. Nguyen <nguyenb@codeaurora.org>
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1590139950-7288-6-git-send-email-sartgarg@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Update dll_config_3 as per the host clock frequency as specified in the
DLL Hardware Reference Guide.
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1590139950-7288-5-git-send-email-sartgarg@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With SDCC v5.1.0, additional setting needed for enabling DLL output.
The dll-user-control register need to be configured during dll
initialization for getting proper dll output.
Without this configuration, we don't get the DLL lock status properly.
Also update the DLL register settings according to the SDCC Hardware
Programming Guide.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1590139950-7288-4-git-send-email-sartgarg@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When auto calibration timeouts, calibration is disabled and fail-safe
drive strength values are programmed based on the signal voltage.
Different fail-safe drive strength values based on voltage are
applicable only for SoCs supporting 3V3 and 1V8 pad controls.
So, this patch avoids reading these properties from the device tree
for SoCs not using pad controls and the warning of missing properties
will not show up on these SoC platforms.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1590005337-1087-1-git-send-email-skomatineni@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the tmio device is attached to a genpd (PM domain), that genpd may have
->start|stop() callback assigned to it. To make sure the device is
accessible during ->probe(), genpd's ->start() callback must be invoked,
which is currently managed by tmio_mmc_host_probe(). However, it's likely
that may be too late for some cases, as registers may be read and written
way before that point.
To fix the behaviour, let's move the call to dev_pm_domain_start() from
tmio_mmc_host_probe() into those clients that needs it. From discussions at
linux-mmc mailing list, it turned out that it should be sufficient to do
this for the SDHI renesas variants, hence the call is move to
renesas_sdhi_probe().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20200519152445.6922-1-ulf.hansson@linaro.org
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Before calling tmio_mmc_host_probe(), the caller is required to enable
clocks for its device, as to make it accessible when reading/writing
registers during probe.
Therefore, the responsibility to disable these clocks, in the error path of
->probe() and during ->remove(), is better managed outside
tmio_mmc_host_remove(). As a matter of fact, callers of
tmio_mmc_host_remove() already expects this to be the behaviour.
However, there's a problem with tmio_mmc_host_remove() when the Kconfig
option, CONFIG_PM, is set. More precisely, tmio_mmc_host_remove() may then
disable the clock via runtime PM, which leads to clock enable/disable
imbalance problems, when the caller of tmio_mmc_host_remove() also tries to
disable the same clocks.
To solve the problem, let's make sure tmio_mmc_host_remove() leaves the
device with clocks enabled, but also make sure to disable the IRQs, as we
normally do at ->runtime_suspend().
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200519152434.6867-1-ulf.hansson@linaro.org
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
This driver has been developed as a separate module starting
from the similar sdhci-esdhc-imx.c.
Reasons for a separate sdchi-esdhc-mcf driver:
- m68K architecture does not support devicetrees, so modifying
sdhci-of-esdhc.c that is devicetree-related adding platform data
seems not appropriate,
- clock-related part, has to be implemented specifically for
mcf5441x family (see esdhc_mcf_pltfm_set_clock()),
- this is a big endian cpu accessing a big endian controller,
but about sdma, this controller does not support hw swap, which
needs to be handled with specific code,
- some other minor differences but mainly to avoid risks on
tweaking inside largely used imx driver. Adding just a small
size ColdFire-specific driver, with benefits in a further less
risky maintenance.
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200518191742.1251440-3-angelo.dureghello@timesys.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some controller as the ColdFire eshdc may require an endianness
byte swap, because DMA read endianness is not configurable.
Facilitate using the bounce buffer for this by adding
->copy_to_bounce_buffer().
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200518191742.1251440-2-angelo.dureghello@timesys.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Kbuild test robot reports the following warning in lines 56 and 87 of
drivers/mmc/host/meson-mx-sdhc-clkc.c:
Using plain integer as NULL pointer
Drop the integer value from the struct initialization to fix that
warning. This will still ensure that the compiler will zero out the
struct so it's in a well-defined state.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20200517222907.1277787-2-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For Meson8 and Meson8b SoCs the vendor driver follows the following
pattern:
- for eMMC and SD cards in .set_pdma it sets:
pdma->rxfifo_manual_flush = 1;
- for SDIO cards in .set_pdma it sets:
pdma->rxfifo_manual_flush = 0;
- before syncing the DMA read buffer is sets:
pdma->rxfifo_manual_flush |= 0x02;
Set the second bit of MESON_SDHC_PDMA_RXFIFO_MANUAL_FLUSH without
clearing the first bit before syncing the DMA read buffer. This fixes a
problem where Meson8 and Meson8b SoCs would read random garbage from SD
cards. It is not clear why it worked for eMMC cards. This manifested in
the following errors when plugging in an SD card:
unrecognised SCR structure version <random number>
Cc: Thomas Graichen <thomas.graichen@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20200517222907.1277787-1-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For an x86_64 allmodconfig build Stephen reports that building
meson-mx-sdhc-clkc.o warns that MODULE_LICENSE is missing and when
linking meson_mx_sdhc_register_clkc cannot be found.
Compile the MMC controller driver together with the build-in clock
controller driver into one module rather than using two separate
modules to fix these issues.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20200518060811.1499962-1-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need a different set_uhs_signaling implementation for
MMC_TIMING_MMC_HS and MMC_TIMING_MMC_HS400.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200513182602.3636a551@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHC MMC host controller on Amlogic SoCs provides an eMMC and MMC
card interface with 1/4/8-bit bus width.
It supports eMMC spec 4.4x/4.5x including HS200 (up to 100MHz clock).
The public S805 datasheet [0] contains a short documentation about the
registers. Unfortunately it does not describe how to use the registers
to make the hardware work. Thus this driver is based on reading (and
understanding) the Amlogic 3.10 GPL kernel code.
Some hardware details are not easy to see. Jianxin Pan was kind enough
to answer my questions:
The hardware has built-in busy timeout support. The maximum timeout is
30 seconds. This is only documented in Amlogic's internal
documentation.
The controller only works with very specific clock configurations. The
details are not part of the public datasheet. In my own words the
supported configurations are:
- 399.812kHz: clkin = 850MHz div = 2126 sd_rx_phase = 63
- 1MHz: clkin = 850MHz div = 850 sd_rx_phase = 55
- 5.986MHz: clkin = 850MHz div = 142 sd_rx_phase = 24
- 25MHz: clkin = 850MHz div = 34 sd_rx_phase = 15
- 47.222MHz: clkin = 850MHz div = 18 sd_rx_phase = 11/15 (SDR50/HS)
- 53.125MHz: clkin = 850MHz div = 16 sd_rx_phase = (tuning)
- 70.833MHz: clkin = 850MHz div = 12 sd_rx_phase = (tuning)
- 85MHz: clkin = 850MHz div = 10 sd_rx_phase = (tuning)
- 94.44MHz: clkin = 850MHz div = 9 sd_rx_phase = (tuning)
- 106.25MHz: clkin = 850MHz div = 8 sd_rx_phase = (tuning)
- 127.5MHz: clkin = 1275MHz div = 10 sd_rx_phase = (tuning)
- 141.667MHz: clkin = 850MHz div = 6 sd_rx_phase = (tuning)
- 159.375MHz: clkin = 1275MHz div = 8 sd_rx_phase = (tuning)
- 212.5MHz: clkin = 1275MHz div = 6 sd_rx_phase = (tuning)
- (sd_tx_phase is always 1, 94.44MHz is not listed in the datasheet
but this is what the 3.10 BSP kernel on Odroid-C1 actually uses)
NOTE: CMD23 support is disabled for now because it results in command
timeouts and thus decreases read performance.
Tested-by: Wei Wang <lnykww@gmail.com>
Tested-by: Xin Yin <yinxin_1989@aliyun.com>
Reviewed-by: Xin Yin <yinxin_1989@aliyun.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200512204147.504087-3-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use FIELD_GET and FIELD_PREP to get access to the register fields. Delete
the shift macros and use GENMASK() for the touched macros.
Note that, this has the side-effect of changing the constants to 64-bit on
64-bit platforms.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Link: https://lore.kernel.org/r/20200511062828.1791484-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, tmio_mmc_irq() handler is registered before the host is
fully initialized by tmio_mmc_host_probe(). I did not previously notice
this problem.
The boot ROM of a new Socionext SoC unmasks interrupts (CTL_IRQ_MASK)
somehow. The handler is invoked before tmio_mmc_host_probe(), then
emits noisy call trace.
Move devm_request_irq() below tmio_mmc_host_probe().
Fixes: 3fd784f745 ("mmc: uniphier-sd: add UniPhier SD/eMMC controller driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200511062158.1790924-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
GL9763E supports High Speed SDR, High Speed DDR, HS200, HS400, Enhanced
Strobe in HS400 mode, 1/4/8 bits data bus and 3.3/1.8V.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20200508064154.13473-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC_CAP_ERASE bit is no longer used by the mmc core as erase, discard
and trim operations are now always supported. Therefore, drop the bit and
move all mmc hosts away from using it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Link: https://lore.kernel.org/r/20200508112902.23575-1-ulf.hansson@linaro.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Step by step, mmc host drivers and the mmc core have been improved in
regards to support erase/discard/trim operations. We have now reached a
point when it no longer seems reasonable to use an opt-in approach to
enable the functionality. Therefore, let's switch to make the operations
always supported.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200508112853.23525-1-ulf.hansson@linaro.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Using a fixed 1s polling timeout for all commands is a bit problematic.
For some commands it means waiting longer than needed for the polling to be
aborted, which may not a big issue, but still. For other commands, like for
an erase (CMD38) that uses a R1B response, may require longer timeouts than
1s. In these cases, we may end up treating the command as it failed, while
it just needed some more time to complete successfully.
Fix the problem by respecting the cmd->busy_timeout, which is provided by
the mmc core.
Note that, even if the sdricoh_cs driver may currently not support HW busy
detection on DAT0, some comments in the code refer to that the HW may
support it. Therefore, it seems better to be proactive in this case.
Cc: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200508095228.14230-1-ulf.hansson@linaro.org
Rather than to poll in a busy-loop, let's convert into using
read_poll_timeout() and insert a small delay between each polling attempts.
In particular, this avoids hogging the CPU.
Additionally, to convert to read_poll_timeout() we also need to switch from
using a specific number of polling attempts, into a specific timeout in us
instead. The previous 100000 attempts, is translated into a total timeout
of total 1s, as that seemed like reasonable value to pick.
Cc: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200508095218.14177-1-ulf.hansson@linaro.org
Rather than to poll in a busy-loop, let's convert into using
read_poll_timeout() and insert a small delay between each polling attempts.
In particular, this avoids hogging the CPU.
Additionally, to convert to read_poll_timeout() we also need to switch from
using a specific number of polling attempts, into a specific timeout in us
instead. The previous 100000 attempts, is translated into a total timeout
of total 1s, as that seemed like reasonable value to pick.
Cc: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200508095210.14123-1-ulf.hansson@linaro.org
Some commands uses R1B responses, which means the card may assert the DAT0
line to signal busy for a period of time, after it has received the
command. The mmc core normally specifies the busy period for the command in
the cmd->busy_timeout. Ideally the driver should respect it, but that
requires quite some update of the code, so let's defer that to someone with
the HW at hand.
Instead, let's inform the mmc core about the maximum supported busy timeout
in ->max_busy_timeout during ->probe(). This value corresponds to the fixed
~2s timeout of the polling loop, implemented in cb710_wait_for_event(). In
this way, we let the mmc core validate the needed timeout, which may lead
to that it converts from a R1B into a R1 response and then use CMD13 to
poll for busy completion.
In other words, this change enables support for commands with longer busy
periods than 2s, like erase (CMD38) for example.
Cc: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-7-ulf.hansson@linaro.org
The 'pengutronix' address is defunct for years. Use the proper contact
address.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200502142840.19418-1-wsa@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Following eMMC JEDEC JESD84-B51 standard, an enhanced form of
rpmb is supported. What this enhanced mode supports is in addition
to be able to write one rpmb or two rpmb frames at a time,
32 frames can be written at a time.
Expose this information present in ext csd field so that the
user space application that wants to make use of this can do so.
Signed-off-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1588341189-4371-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the comment in mmc_sdio_reinit_card(), some SDIO cards may
require a "[CMD5,5,3,7] init sequence", which isn't always obeyed in
mmc_sdio_init_card(). Especially, when we end up retrying the UHS-I
specific initialization, there is a missing CMD5.
Let's update the code to make the behaviour consistent and let's also take
the opportunity to clean up the code a bit, to avoid open coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200430091640.455-5-ulf.hansson@linaro.org
While initializing an SDIO card in mmc_sdio_init_card(), we may need to
retry the UHS-I specific initialization, in case the first attempt fails.
This leads to resending a CMD8, but also to restart from scratch with the
so called OCR mask negotiations. This is unnecessary as we already have a
negotiated OCR mask, so let's use that instead. In this way, the behaviour
also becomes more consistent with other similar paths.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200430091640.455-4-ulf.hansson@linaro.org
Over the years, the code in mmc_sdio_init_card() has grown to become quite
messy. Unfortunate this has also lead to that several paths are leaking
memory in form of an allocated struct mmc_card, which includes additional
data, such as initialized struct device for example.
Unfortunate, it's a too complex task find each offending commit. Therefore,
this change fixes all memory leaks at once.
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200430091640.455-3-ulf.hansson@linaro.org
During some scenarios mmc_sdio_init_card() runs a retry path for the UHS-I
specific initialization, which leads to removal of the previously allocated
card. A new card is then re-allocated while retrying.
However, in one of the corresponding error paths we may end up to remove an
already removed card, which likely leads to a NULL pointer exception. So,
let's fix this.
Fixes: 5fc3d80ef4 ("mmc: sdio: don't use rocr to check if the card could support UHS mode")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200430091640.455-2-ulf.hansson@linaro.org
Even though specifying OPP's in device tree is optional, ignoring all errors
reported by dev_pm_opp_of_add_table() means we can't distinguish between a
missing OPP table and a wrong/buggy OPP table. While missing OPP table
(dev_pm_opp_of_add_table() returns a -ENODEV in such case) can be ignored,
a wrong/buggy OPP table in device tree should make the driver error out.
while we fix that, lets also fix the variable names for opp/opp_table to
avoid confusion and name them opp_table/has_opp_table instead.
Suggested-by: Matthias Kaehlcke <matthias@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/1588080785-6812-10-git-send-email-rnayak@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With R-Car Gen3, CRC error occue at the following TAPs.
H3, M3W 1.3, M3N... TAP=2,3,6,7
M3W 3.0 ... TAP=1,3,5,7
(Note: for 4tap SoCs, the numbers get divided by 2)
Do not use these TAPs in HS400, and also don't use auto correction but
manual correction.
We check for bad taps in two places:
1) After tuning HS400: Then, we select a neighbouring TAP. One of them
must be good, because there are never three bad taps in a row.
Retuning won't help because we just finished tuning.
2) After a manual correction request: Here, we can't switch to the
requested TAP. But we can retune (if the HS200 tuning was good)
because the environment might have changed since the last tuning.
If not, we stay on the same TAP.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: refactored to match upstream driver, reworded commit msg]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200423130432.9990-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For ES1.2, add a comment explaining the situation. For ES1.3 (and
later, although unlikely), add a new entry defining it as 4tap.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200423130432.9990-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using a fixed 3s polling timeout for all commands with R1B responses is a
bit problematic.
For some commands it means waiting longer than needed for the polling to be
aborted, which may not a big issue, but still. For other commands, like for
an erase (CMD38), may require longer timeouts than 3s. In these cases, we
may end up treating the command as it failed, while it just needed some
more time to complete successfully.
Fix the problem by respecting the cmd->busy_timeout, which is provided by
the mmc core.
Cc: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-19-ulf.hansson@linaro.org
Clarify the use of r1b_timeout, by renaming it to MMC_SPI_R1B_TIMEOUT_MS
and by dropping the corresponding confusing comment about it.
Additionally, let's also add a new define, MMC_SPI_INIT_TIMEOUT_MS and use
it during the initialization. Even if these two defines are given the same
value, the split makes it easier to understand them.
Cc: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-18-ulf.hansson@linaro.org
Using a fixed 1s timeout for all commands (and data transfers) is a bit
problematic.
For some commands it means waiting longer than needed for the timer to
expire, which may not a big issue, but still. For other commands, like for
an erase (CMD38) that uses a R1B response, may require longer timeouts than
1s. In these cases, we may end up treating the command as it failed, while
it just needed some more time to complete successfully.
Fix the problem by respecting the cmd->busy_timeout, which is provided by
the mmc core.
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-17-ulf.hansson@linaro.org
Some commands uses R1B responses, which means the card may assert the DAT0
line to signal busy for a period of time, after it has received the
command. The mmc core normally specifies the busy period for the command in
the cmd->busy_timeout. Ideally the driver should respect it, but that
requires quite some update of the code, so let's defer that to someone with
the HW at hand.
Instead, let's inform the mmc core about the maximum supported busy timeout
in ->max_busy_timeout during ->probe(). This value corresponds to the fixed
1s timeout used by tifm_sd. In this way, we let the mmc core validate the
needed timeout, which may lead to that it converts from a R1B into a R1
response and then use CMD13 to poll for busy completion.
In other words, this change enables support for commands with longer busy
periods than 1s, like erase (CMD38) for example.
Cc: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-16-ulf.hansson@linaro.org
The in-parameter timeout is always set to TRANSFER_TIMEOUT by the callers
of sdricoh_query_status(), hence let's drop it.
Cc: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-12-ulf.hansson@linaro.org
For commands that doesn't involve to prepare a data transfer, owl-mmc is
using a fixed 30s response timeout. This is a bit problematic.
For some commands it means waiting longer than needed for the completion to
expire, which may not a big issue, but still. For other commands, like for
an erase (CMD38) that uses a R1B response, may require longer timeouts than
30s. In these cases, we may end up treating the command as it failed, while
it just needed some more time to complete successfully.
Fix the problem by respecting the cmd->busy_timeout, which is provided by
the mmc core.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-8-ulf.hansson@linaro.org
Some commands uses R1B responses, which means the card may assert the DAT0
line to signal busy for a period of time, after it has received the
command. The mmc core normally specifies the busy period for the command in
the cmd->busy_timeout. Ideally the driver should respect it, but that
requires quite some update of the code, so let's defer that to someone with
the HW at hand.
Instead, let's inform the mmc core about the maximum supported busy timeout
in ->max_busy_timeout during ->probe(). This value corresponds to the fixed
5s timeout used by jz4740. In this way, we let the mmc core validate the
needed timeout, which may lead to that it converts from a R1B into a R1
response and then use CMD13 to poll for busy completion.
In other words, this change enables support for commands with longer busy
periods than 5s, like erase (CMD38) for example.
Cc: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200414161413.3036-5-ulf.hansson@linaro.org
Fix the following sparse warning:
drivers/mmc/host/sdhci-pci-o2micro.c:497:6: warning: symbol
'sdhci_pci_o2_set_clock' was not declared. Should it be static?
drivers/mmc/host/sdhci-pci-o2micro.c:512:5: warning: symbol
'sdhci_pci_o2_probe_slot' was not declared. Should it be static?
drivers/mmc/host/sdhci-pci-o2micro.c:581:5: warning: symbol
'sdhci_pci_o2_probe' was not declared. Should it be static?
drivers/mmc/host/sdhci-pci-o2micro.c:786:5: warning: symbol
'sdhci_pci_o2_resume' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1587624199-96926-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes coccicheck warning:
drivers/mmc/core/debugfs.c:222:0-23: WARNING: mmc_clock_fops should be
defined with DEFINE_DEBUGFS_ATTRIBUTE
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files
Fixes: 703aae3d09 ("mmc: add a file to debugfs for changing host clock at runtime")
Fixes: a04c50aaa9 ("mmc: core: no need to check return value of debugfs_create functions")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1587633319-19835-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If sdhci-of-at91.c is compiled without CONFIG_HAVE_CLK, the line
caps1 |= FIELD_PREP(SDHCI_CLOCK_MUL_MASK, clk_mul);
... emits "FIELD_PREP: value too large for the field" warning.
The compiler seems to decide clk_mul is constant (unsigned int)-1,
because clk_get_rate() returns 0 when CONFIG_HAVE_CLK is disabled.
Add HAVE_CLK to the depenency since this driver does not work without
the clock APIs anyway.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Link: https://lore.kernel.org/r/20200422153401.7913-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
After TAP refactorization, we can use 'unsigned int' for two more
variables because all the calculations work on this type now.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200420170230.9091-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch fix a power-on issue, and avoid to retry the power sequence.
In power off sequence: sdmmc must set pwr_reg in "power-cycle" state
(value 0x2), to prevent the card from being supplied through the signal
lines (all the lines are driven low).
In power on sequence: when the power is stable, sdmmc must set pwr_reg
in "power-off" state (value 0x0) to drive all signal to high before to
set "power-on".
To avoid writing the same value to the power register several times, this
register is cached by the pwr_reg variable. At probe pwr_reg is initialized
to 0 by kzalloc of mmc_alloc_host.
Like pwr_reg value is 0 at probing, the power on sequence fail because
the "power-off" state is not writes (value 0x0) and the lines
remain drive to low.
This patch initializes "pwr_reg" variable with power register value.
This it done in sdmmc variant init to not disturb default mmci behavior.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200420161831.5043-1-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On some qualcomm SoCs we need to vote on a performance state of a power
domain depending on the clock rates. Hence move to using OPP api to set
the clock rate and performance state specified in the OPP table.
On platforms without an OPP table, dev_pm_opp_set_rate() is eqvivalent to
clk_set_rate()
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/1587132279-27659-10-git-send-email-rnayak@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some commands uses R1B responses, which means the card may assert the DAT0
line to signal busy for a period of time, after it has received the
command. The mmc core normally specifies the busy period for the command in
the cmd->busy_timeout. Ideally the driver should respect it, but that
requires quite some update of the code, so let's defer that to someone with
the HW at hand.
Instead, let's inform the mmc core about the maximum supported busy timeout
in ->max_busy_timeout during ->probe(). This value corresponds to the fixed
4s timeout used by usdhi6rol0. In this way, we let the mmc core validate
the needed timeout, which may lead to that it converts from a R1B into a R1
response and then use CMD13 to poll for busy completion.
In other words, this change enables support for commands with longer busy
periods than 4s, like erase (CMD38) for example.
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Lars Persson <lars.persson@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Link: https://lore.kernel.org/r/20200414161413.3036-6-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using a fixed 2s timeout for all commands is a bit problematic.
For some commands it means waiting longer than needed for the timer to
expire, which may not a big issue, but still. For other commands, like for
an erase (CMD38) that uses a R1B response, may require longer timeouts than
2s. In these cases, we may end up treating the command as it failed, while
it just needed some more time to complete successfully.
Fix the problem by respecting the cmd->busy_timeout, which is provided by
the mmc core.
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20200414161413.3036-4-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Setting the timer on a per request basis, is rather limiting as the timer
really depends on what commands that is to be sent as part of the request.
Therefore improve the behaviour by programming the timer per command basis
instead.
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20200414161413.3036-3-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When atmci_request_end() is about to finish a request for one slot, there
is a possibility that there is new request queued for another slot. If this
turns out to be the case, the new request is started and the timer is
re-programmed for it.
Although, a few lines below in atmci_request_end(), this timer becomes
deleted, likely corresponding to the other recently completed request. This
looks wrong, so let's fix it.
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20200414161413.3036-2-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ADMA_ERR_SIZE_EN bit of VENDOR_SPECIFIC_FUNC register controls
ADMA length mismatch error interrupt. Enable it by default.
And update all bit shift defines with BIT macro.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1587363626-20413-4-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci-msm can support auto cmd12.
So enable SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12 quirk.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1587363626-20413-3-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When use one SDIO wifi which enable the runtime PM feature on i.MX6SX,
we meet system hang. This hang happened during the usdhc runtime resume,
in sdhci_init(), when call the sdhci_set_default_irqs. One interrupt
(SDHCI_INT_CARD_INT) triggered just after the host->ier update and before
the write of register SDHCI_SIGNAL_ENABLE. So in sdhci_irq, it will skip
the call of sdio_signal_irq() because current host->ier do not set the
SDHCI_INT_CARD_INT. So this SDIO wifi interrupt always keep triggered,
let the system stuck in irq handle, can't response any other thread.
This patch add spin lock for the sdhci_set_default_irqs to fix this issue.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1586941255-9237-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement the request_atomic() API for nonremovable cards, that means
we can submit next request in the irq hard handler context to reduce
latency.
Moreover factor out the AUTO CMD23 checking into a separate function
to reduce duplicate code.
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/60142fe6c6c1dbba2696e775564ae2166786f0bc.1586744073.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement the request_atomic() ops for the sdhci driver to process
one request in the atomic context if the card is nonremovable.
Moreover, we should return BUSY flag if controller has not released
the inhibit bits to allow HSQ trying to send request again in non-atomic
context.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/9ed34afa9fb42e0c234065cac5401d7826942b55.1586744073.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SD host controller can process one request in the atomic context if
the card is nonremovable, which means we can submit next request in the
irq hard handler when using the MMC host software queue to reduce the
latency. Thus this patch adds a new API request_atomic() for the host
controller, as well as adding support for host software queue to submit
a request by the new request_atomic() API.
Moreover there is an unusual case that the card is busy when trying to
send a command, and we can not polling the card status in interrupt
context by using request_atomic() to dispatch requests. Thus we should
queue a work to try again in the non-atomic context in case the host
releases the busy signal later.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/a344e27e506cb2329073cbd5cf65e15cc3cbeba9.1586744073.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Spending time under spinlock increases IRQ latencies and also
response times because preemption is disabled.
sdhci_send_command() waits up to 10 ms under spinlock for inhibit bits
to clear. In general inhibit bits will not be set, but there may be
corner cases, especially in the face of errors, where waiting helps.
There might also be dysfunctional hardware that needs the waiting. So
retain the legacy behaviour but do not wait for inhibit bits while under
spinlock. Instead adjust the logic to enable waiting while not under
spinlock. That is mostly straight forward, but in the interrupt handler
it requires deferring an "inhibited" command to the IRQ thread where
sleeping is allowed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200412090349.1607-6-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for further changes, tidy sdhci_request() a bit.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200412090349.1607-5-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_finish_data() is defined before it is referenced, so forward
declaration is not necessary.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200412090349.1607-4-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_send_command() has not been used outside of sdhci.c for many
years. Stop exporting it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200412090349.1607-3-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add 2 helper functions to make the use of the auto-CMD23 flag more
readable.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200412090349.1607-2-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the well defined HIGH_SPEED_BUS_SPEED macro in mmc_sd_switch_hs()
to make code more readable.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200410145643.630b0731@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of reimplementing the logic in mmc_regulator_set_vqmmc(), use the
mmc code function directly.
This also allows us to fix a related issue on STM32MP1, when a voltage
switch of 1.8V is done for the eMMC, but the current level is already set
to 1.8V. More precisely, in this scenario the call to the
->post_sig_volt_switch() hangs, indefinitely waiting for the voltage switch
to complete. Fix this problem by checking if mmc_regulator_set_vqmmc()
returned 1 and then skip invoking the callback.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20200416163649.336967-3-marex@denx.de
[Ulf: Updated the commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adjust mmc_regulator_set_vqmmc() to return 1 if the voltage switch was
skipped because the regulator voltage was already correct. This allows
drivers to detect such condition and possibly skip various voltage
switching extras.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20200416163649.336967-2-marex@denx.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Patch all drivers which use mmc_regulator_set_vqmmc() and prepare them for
the fact that mmc_regulator_set_vqmmc() can return a value > 0, which would
happen if the signal voltage switch did NOT happen, because the voltage was
already set correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20200416163649.336967-1-marex@denx.de
[Ulf: Re-worked/simplified the code a bit]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clang warns:
drivers/mmc/host/sdhci-of-arasan.c:784:9: warning: variable 'ret' is
uninitialized when used here [-Wuninitialized]
return ret;
^~~
drivers/mmc/host/sdhci-of-arasan.c:738:9: note: initialize the variable
'ret' to silence this warning
int ret;
^
= 0
drivers/mmc/host/sdhci-of-arasan.c:860:9: warning: variable 'ret' is
uninitialized when used here [-Wuninitialized]
return ret;
^~~
drivers/mmc/host/sdhci-of-arasan.c:810:9: note: initialize the variable
'ret' to silence this warning
int ret;
^
= 0
2 warnings generated.
This looks like a copy paste error. Neither function has handling that
needs ret so just remove it and return 0 directly.
Link: https://github.com/ClangBuiltLinux/linux/issues/996
Reported-by: kernelci.org bot <bot@kernelci.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20200416182402.16858-1-natechancellor@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No need to call platform_get_resource twice when we still have the
pointer from before. Also, use '%pa' for a resource_size_t pointer.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200408142252.21958-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
When tuning HS400, if all TAPS are good, we can utilize the SMPCMP
register to select the optimal TAP. For that, we populate a second
bitmap with SMPCMP results and query it in case the regular bitmap is
full (= all good).
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200408094638.10375-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The comment and the define about how TAPs are selected were confusing to
me because the good TAP was only valid if it was bigger than a *_MAX_*
value. Rename the define and adapt the comment to what really happens.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200408094638.10375-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To select the best TAP, we need to find the longest stream of set bits
in a bit field. There is now a helper function for bitmaps which
iterates over all region of set bits. Using it makes the code much more
concise and easier to understand. Double so, because we need to handle
two bitmaps in the near future. Remove a superfluous comment while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200408094638.10375-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use FIELD_GET and FIELD_PREP to get access to the register fields. Delete
the shift macros and use GENMASK() for the touched macros.
Note that, this has the side-effect of changing the constants to 64-bit on
64-bit platforms.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200408072105.422-2-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the SDHCI specification, the Capabilities Register (Offset 0x40h)
is the 64-bit width register, but in Linux, it is represented as two
registers, SDHCI_CAPABILITIES and SDHCI_CAPABILITIES_1 so that drivers
can use 32-bit register accessors.
The upper 32-bit field is associated with SDHCI_CAPABILITIES_1.
Move the definition of SDHCI_CAPABILITIES_1 to the correct place.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200408072105.422-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI clock operations are platform specific. So it better to define
them separately for particular platform. This will prevent multiple
if..else conditions and will make it easy for user to add their own
clock operations handlers.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1586195015-128992-6-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Existing driver code has the platform specific structures scattered
throughout the driver code. Rearrange the platform specific data
structures for more modularity and readability. This will help in adding
new static functions with more ease.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1586195015-128992-5-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is 'struct sdhci_arasan_data' but also
'struct sdhci_arasan_of_data sdhci_arasan_data'. Rename the latter to
avoid confusion with the name of the struct.
Reported-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1586195015-128992-4-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support to set tap delays for Xilinx Versal SD controller. The tap
delay registers have moved to SD controller space in Versal. Make the
changes accordingly.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1586195015-128992-3-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The in-parameter struct mmc_data *data is never NULL, because the caller
always provides a valid pointer. Hence drop the corresponding redundant
code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200407143903.22477-1-ulf.hansson@linaro.org
The in-parameter "wait" is always set to 0 by the caller, hence just drop
it and its corresponding code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Manuel Lauss <manuel.lauss@gmail.com>
Link: https://lore.kernel.org/r/20200406114337.8802-1-ulf.hansson@linaro.org
The MMC_CAP_ERASE and MMC_CAP_CMD23 flags are already being set in the
common sdhci_setup_host(). This makes it redundant to set them for
sdhci-sprd, so let's drop them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200406113724.8504-1-ulf.hansson@linaro.org
Instead of explicitly checking for SDIO specific requests and then
returning an error code, let's set MMC_CAP2_NO_SDIO to tell the mmc core to
prevent them altogether.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200401145531.23247-1-ulf.hansson@linaro.org
The data structure member “rpmb->md” was passed to a call of the function
“mmc_blk_put” after a call of the function “put_device”. Reorder these
function calls to keep the data accesses consistent.
Fixes: 1c87f73578 ("mmc: block: Fix bug when removing RPMB chardev ")
Signed-off-by: Peng Hao <richard.peng@oppo.com>
Cc: stable@vger.kernel.org
[Uffe: Fixed up mangled patch and updated commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Previous to commit 511ce378e1 ("mmc: Add MMC host software queue
support"), removing MMC_CAP2_CQE was enough to disable command queuing, but
now the cqe_ops must also be NULL otherwise ->cqe_enable() will be
called. Fix SDHCI_QUIRK_BROKEN_CQE to do that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 511ce378e1 ("mmc: Add MMC host software queue support")
Link: https://lore.kernel.org/r/20200518120939.1399-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
First, it should be noted that the CQE timeout (60 seconds) is substantial
so a CQE request that times out is really stuck, and the race between
timeout and completion is extremely unlikely. Nevertheless this patch
fixes an issue with it.
Commit ad73d6fead ("mmc: complete requests from ->timeout")
preserved the existing functionality, to complete the request.
However that had only been necessary because the block layer
timeout handler had been marking the request to prevent it from being
completed normally. That restriction was removed at the same time, the
result being that a request that has gone will have been completed anyway.
That is, the completion was unnecessary.
At the time, the unnecessary completion was harmless because the block
layer would ignore it, although that changed in kernel v5.0.
Note for stable, this patch will not apply cleanly without patch "mmc:
core: Fix recursive locking issue in CQE recovery path"
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: ad73d6fead ("mmc: complete requests from ->timeout")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200508062227.23144-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Consider the following stack trace
-001|raw_spin_lock_irqsave
-002|mmc_blk_cqe_complete_rq
-003|__blk_mq_complete_request(inline)
-003|blk_mq_complete_request(rq)
-004|mmc_cqe_timed_out(inline)
-004|mmc_mq_timed_out
mmc_mq_timed_out acquires the queue_lock for the first
time. The mmc_blk_cqe_complete_rq function also tries to acquire
the same queue lock resulting in recursive locking where the task
is spinning for the same lock which it has already acquired leading
to watchdog bark.
Fix this issue with the lock only for the required critical section.
Cc: <stable@vger.kernel.org>
Fixes: 1e8e55b670 ("mmc: block: Add CQE support")
Suggested-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1588868135-31783-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the request completion path with CQE, request type is being checked
after the request is getting completed. This is resulting in returning
the wrong request type and leading to the IO hang issue.
ASYNC request type is getting returned for DCMD type requests.
Because of this mismatch, mq->cqe_busy flag is never getting cleared
and the driver is not invoking blk_mq_hw_run_queue. So requests are not
getting dispatched to the LLD from the block layer.
All these eventually leading to IO hang issues.
So, get the request type before completing the request.
Cc: <stable@vger.kernel.org>
Fixes: 1e8e55b670 ("mmc: block: Add CQE support")
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1588775643-18037-2-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Need to clear some bits in a vendor-defined register after reboot from
Windows 10.
Fixes: e51df6ce66 ("mmc: host: sdhci-pci: Add Genesys Logic GL975x support")
Reported-by: Grzegorz Kowal <custos.mentis@gmail.com>
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Grzegorz Kowal <custos.mentis@gmail.com>
Link: https://lore.kernel.org/r/20200504063957.6638-1-benchuanggli@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The kernel prints a message similar to
"[ 28.881959] do_IRQ: 5.36 No irq handler for vector"
when GL975x resumes from suspend. Implement a resume callback to fix this.
Fixes: 31e43f3189 ("mmc: sdhci-pci-gli: Enable MSI interrupt for GL975x")
Co-developed-by: Renius Chen <renius.chen@genesyslogic.com.tw>
Signed-off-by: Renius Chen <renius.chen@genesyslogic.com.tw>
Tested-by: Dave Flogeras <dflogeras2@gmail.com>
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Tested-by: Vineeth Pillai <vineethrp@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200427103048.20785-1-benchuanggli@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Samuel Zou <zou_wei@huawei.com>
[Samuel Zou: Make sdhci_pci_gli_resume() static]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Making COMMON_CLK a visible option causes the sparc allyesconfig to fail
to build like so:
sparc64-linux-ld: drivers/mmc/host/meson-mx-sdio.o: in function `meson_mx_mmc_remove':
meson-mx-sdio.c:(.text+0x70): undefined reference to `of_platform_device_destroy'
sparc64-linux-ld: drivers/mmc/host/meson-mx-sdio.o: in function `meson_mx_mmc_probe':
meson-mx-sdio.c:(.text+0x9e4): undefined reference to `of_platform_device_create'
sparc64-linux-ld: meson-mx-sdio.c:(.text+0xdd4): undefined reference to `of_platform_device_destroy'
This is because the implementation of of_platform_device_destroy() is
inside an #ifdef CONFIG_OF_ADDRESS section of drivers/of/platform.c.
This driver already depends on OF being enabled, so let's tighten that
constrain a little more so that it depends on OF_ADDRESS instead. This
way we won't try to build this driver on platforms that don't have this
function.
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20200409064416.83340-7-sboyd@kernel.org
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
BIOS writers have begun the practice of setting 40 ohm eMMC driver strength
even though the eMMC may not support it, on the assumption that the kernel
will validate the value against the eMMC (Extended CSD DRIVER_STRENGTH
[offset 197]) and revert to the default 50 ohm value if 40 ohm is invalid.
This is done to avoid changing the value for different boards.
Putting aside the merits of this approach, it is clear the eMMC's mask
of supported driver strengths is more reliable than the value provided
by BIOS. Add validation accordingly.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 51ced59cc0 ("mmc: sdhci-pci: Use ACPI DSM to get driver strength for some Intel devices")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200422111629.4899-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For some reason the Host Control2 register of the Xenon SDHCI controller
sometimes reports the bit representing 1.8V signaling as 0 when read
after it was written as 1. Subsequent read reports 1.
This causes the sdhci_start_signal_voltage_switch function to report
1.8V regulator output did not become stable
When CONFIG_PM is enabled, the host is suspended and resumend many
times, and in each resume the switch to 1.8V is called, and so the
kernel log reports this message annoyingly often.
Do an empty read of the Host Control2 register in Xenon's
.voltage_switch method to circumvent this.
This patch fixes this particular problem on Turris MOX.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Fixes: 8d876bf472 ("mmc: sdhci-xenon: wait 5ms after set 1.8V...")
Cc: stable@vger.kernel.org # v4.16+
Link: https://lore.kernel.org/r/20200420080444.25242-1-marek.behun@nic.cz
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MSM sd host controller is capable of HW busy detection of device busy
signaling over DAT0 line. And it requires the R1B response for commands
that have this response associated with them.
So set the below two host capabilities for qcom SDHC.
- MMC_CAP_WAIT_WHILE_BUSY
- MMC_CAP_NEED_RSP_BUSY
Recent development of the mmc core in regards to this, revealed this as
being a potential bug, hence the stable tag.
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1587363626-20413-2-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Open-coding a timeout loop invariably leads to errors with handling
the timeout properly in one corner case or another. In the case of
cqhci we might report "CQE stuck on" even if it wasn't stuck on.
You'd just need this sequence of events to happen in cqhci_off():
1. Call ktime_get().
2. Something happens to interrupt the CPU for > 100 us (context switch
or interrupt).
3. Check time and; set "timed_out" to true since > 100 us.
4. Read CQHCI_CTL.
5. Both "reg & CQHCI_HALT" and "timed_out" are true, so break.
6. Since "timed_out" is true, falsely print the error message.
Rather than fixing the polling loop, use readx_poll_timeout() like
many people do. This has been time tested to handle the corner cases.
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200413162717.1.Idece266f5c8793193b57a1ddb1066d030c6af8e0@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The recent commit 0d84c3e6a5 ("mmc: core: Convert to
mmc_poll_for_busy() for erase/trim/discard") makes use of the
->card_busy() op for SD cards. This uncovered that the ->card_busy() op
in the Meson SDIO driver was never working right:
while polling the busy status with ->card_busy()
meson_mx_mmc_card_busy() reads only one of the two MESON_MX_SDIO_IRQC
register values 0x1f001f10 or 0x1f003f10. This translates to "three out
of four DAT lines are HIGH" and "all four DAT lines are HIGH", which
is interpreted as "the card is busy".
It turns out that no situation can be observed where all four DAT lines
are LOW, meaning the card is not busy anymore. Upon further research the
3.10 vendor driver for this controller does not implement the
->card_busy() op.
Remove the ->card_busy() op from the meson-mx-sdio driver since it is
not working. At the time of writing this patch it is not clear what's
needed to make the ->card_busy() implementation work with this specific
controller hardware. For all use-cases which have previously worked the
MMC_CAP_WAIT_WHILE_BUSY flag is now taking over, even if we don't have
a ->card_busy() op anymore.
Fixes: ed80a13bb4 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200416183513.993763-3-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Raul E Rangel