A 100MHZ 32-bit timer will be wrapped up less than 43s. Although the
kernel maintains a software high 32-bit count in the tick IRQ. But it's
not applicable to the user mode APPs.
Note: The kernel still uses the lower 32 bits of the timer.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200918132237.3552-9-thunder.leizhen@huawei.com
The ARM SP804 supports a maximum of 32-bit counter, but Hisilicon extends
it to 64-bit. That means, the registers: TimerXload, TimerXValue and
TimerXBGLoad are 64bits, all other registers are the same as those in the
SP804. The driver code can be completely reused except that the register
offset is different.
Use compatible = "hisilicon,sp804" mark as Hisilicon sp804 timer.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200918132237.3552-8-thunder.leizhen@huawei.com
The ARM SP804 supports a maximum of 32-bit counter, but Hisilicon extends
it to 64-bit. That means, the registers: TimerXload, TimerXValue and
TimerXBGLoad are 64bits, all other registers are the same as those in the
SP804. The driver code can be completely reused except that the register
offset is different.
Currently, we get a timer register address by: add the constant register
offset to the timer base address. e.g. "base + TIMER_CTRL". It can not be
dynamically adjusted at run time.
So create a new structure "sp804_timer" to record the original registers
offset, and create a new structure "sp804_clkevt" to record the
calculated registers address. So the "base + TIMER_CTRL" is changed to
"clkevt->ctrl", this will faster than "base + timer->ctrl".
For example:
struct sp804_timer arm_sp804_timer = {
.ctrl = TIMER_CTRL,
};
struct sp804_clkevt clkevt;
clkevt.ctrl = base + arm_sp804_timer.ctrl.
- writel(0, base + TIMER_CTRL);
+ writel(0, clkevt->ctrl);
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200918132237.3552-7-thunder.leizhen@huawei.com
Add two local variables: timer1_base and timer2_base in sp804_of_init(),
to avoid repeatedly calculate the base address of timer2, and make it
easier to recognize timer1. Hope to make the next patch looks more clear.
No functional change.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200918132237.3552-6-thunder.leizhen@huawei.com
writel(0, base + TIMER_CTRL);
... ...
writel(xxx | TIMER_CTRL_PERIODIC, base + TIMER_CTRL);
The timer is just temporarily disabled, and it will be set to periodic
mode later.
The description of the field TimerMode of the register TimerXControl
as shown below:
0 = Timer module is in free-running mode (default)
1 = Timer module is in periodic mode.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200918132237.3552-5-thunder.leizhen@huawei.com
Delete the leading "__" of __sp804_clocksource_and_sched_clock_init() and
__sp804_clockevents_init(), make it looks a little more comfortable.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200918132237.3552-4-thunder.leizhen@huawei.com
Since commit 7484c727b6 ("ARM: realview: delete the RealView board
files") and commit 16956fed35 ("ARM: versatile: switch to DT only
booting and remove legacy code"), there's no one to use the functions
defined or declared in include/clocksource/timer-sp804.h. Delete it.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200918132237.3552-3-thunder.leizhen@huawei.com
Move the clk_get_sys() part into sp804_get_clock_rate(), cleanup the same
code.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200918132237.3552-2-thunder.leizhen@huawei.com
request_irq() is preferred over setup_irq(). The early boot setup_irq()
invocations happen either via 'init_IRQ()' or 'time_init()', while
memory allocators are ready by 'mm_init()'.
Per tglx[1], setup_irq() existed in olden days when allocators were not
ready by the time early interrupts were initialized.
Hence replace setup_irq() by request_irq().
Seldom remove_irq() usage has been observed coupled with setup_irq(),
wherever that has been found, it too has been replaced by free_irq().
A build error that was reported by kbuild test robot <lkp@intel.com>
in the previous version of the patch also has been fixed.
[1] https://lkml.kernel.org/r/alpine.DEB.2.20.1710191609480.1971@nanos
Signed-off-by: afzal mohammed <afzal.mohd.ma@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/91961c77c1cf93d41523f5e1ac52043f32f97077.1582799709.git.afzal.mohd.ma@gmail.com
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The CLOCKSOURCE_OF_DECLARE macro is used widely for the timers to declare the
clocksource at early stage. However, this macro is also used to initialize
the clockevent if any, or the clockevent only.
It was originally suggested to declare another macro to initialize a
clockevent, so in order to separate the two entities even they belong to the
same IP. This was not accepted because of the impact on the DT where splitting
a clocksource/clockevent definition does not make sense as it is a Linux
concept not a hardware description.
On the other side, the clocksource has not interrupt declared while the
clockevent has, so it is easy from the driver to know if the description is
for a clockevent or a clocksource, IOW it could be implemented at the driver
level.
So instead of dealing with a named clocksource macro, let's use a more generic
one: TIMER_OF_DECLARE.
The patch has not functional changes.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
All the clocksource drivers's init function are now converted to return
an error code. CLOCKSOURCE_OF_DECLARE is no longer used as well as the
clksrc-of table.
Let's convert back the names:
- CLOCKSOURCE_OF_DECLARE_RET => CLOCKSOURCE_OF_DECLARE
- clksrc-of-ret => clksrc-of
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
For exynos_mct and samsung_pwm_timer:
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
For arch/arc:
Acked-by: Vineet Gupta <vgupta@synopsys.com>
For mediatek driver:
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
For the Rockchip-part
Acked-by: Heiko Stuebner <heiko@sntech.de>
For STi :
Acked-by: Patrice Chotard <patrice.chotard@st.com>
For the mps2-timer.c and versatile.c changes:
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
For the OXNAS part :
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
For LPC32xx driver:
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
For Broadcom Kona timer change:
Acked-by: Ray Jui <ray.jui@broadcom.com>
For Sun4i and Sun5i:
Acked-by: Chen-Yu Tsai <wens@csie.org>
For Meson6:
Acked-by: Carlo Caione <carlo@caione.org>
For Keystone:
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
For NPS:
Acked-by: Noam Camus <noamca@mellanox.com>
For bcm2835:
Acked-by: Eric Anholt <eric@anholt.net>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Migrate timer-sp driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
There are few more changes worth noticing:
- The clockevent device was disabled by writing: 'TIMER_CTRL_32BIT |
TIMER_CTRL_IE' to ctrl register earlier. i.e. by un-setting the
TIMER_CTRL_ENABLE bit. Its done by writing zero now and should have
the same effect.
- For shutdown and resume we were writing the same value twice to the
register (to disable the timer), which is fixed now.
- Switching to oneshot mode was divided into two parts earlier:
- Firstly set_mode() was writing:
'TIMER_CTRL_32BIT | TIMER_CTRL_IE | TIMER_CTRL_ONESHOT'
to ctrl register (device not enabled yet)
- Then sp804_set_next_event() was enabling the device by writing
'readl(ctrl) | TIMER_CTRL_ENABLE' to the ctrl register. This was
unnecessarily complicated.
- Change this to: Stop device on set_state_oneshot and configure it in
sp804_set_next_event().
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The ARM Dual-Timer SP804 module is peripheral found not only on ARM32
platforms but also on ARM64 platforms.
This patch moves the driver out of arch/arm to driver/clocksource
so that it can be used on ARM64 platforms also.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Olof Johansson <olof@lixom.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Zhen Lei