Add support for Cypress GX3 SuperSpeed to Gigabit Ethernet
Bridge Controller (Vendor=04b4 ProdID=3610).
Patch verified on x64 linux kernel 4.7.4, 4.8.6, 4.9-rc4 systems
with the Kensington SD4600P USB-C Universal Dock with Power,
which uses the Cypress GX3 SuperSpeed to Gigabit Ethernet Bridge
Controller.
A similar patch was signed-off and tested-by Allan Chou
<allan@asix.com.tw> on 2015-12-01.
Allan verified his similar patch on x86 Linux kernel 4.1.6 system
with Cypress GX3 SuperSpeed to Gigabit Ethernet Bridge Controller.
Tested-by: Allan Chou <allan@asix.com.tw>
Tested-by: Chris Roth <chris.roth@usask.ca>
Tested-by: Artjom Simon <artjom.simon@gmail.com>
Signed-off-by: Allan Chou <allan@asix.com.tw>
Signed-off-by: Chris Roth <chris.roth@usask.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
To utilize phylib with interrupt fully than handling some of phy stuff in the MAC driver,
create irq_domain for USB interrupt EP of phy interrupt and
pass the irq number to phy_connect_direct() instead of PHY_IGNORE_INTERRUPT.
Idea comes from drivers/gpio/gpio-dl2.c
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The r8152 driver has been broken since (approx) 3.16.xx
when support was added for hardware RX checksums
on newer chip versions. Symptoms include random
segfaults and silent data corruption over NFS.
The hardware checksum logig does not work on the VER_02
dongles I have here when used with a slow embedded system CPU.
Google reveals others reporting similar issues on Raspberry Pi.
So, disable hardware RX checksum support for VER_02, and fix
an obvious coding error for IPV6 checksums in the same function.
Because this bug results in silent data corruption,
it is a good candidate for back-porting to -stable >= 3.16.xx.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The kalmia_send_init_packet() returns zero or a negative return
code, but gcc has no way of knowing that there cannot be a
positive return code, so it determines that copying the ethernet
address at the end of kalmia_bind() will access uninitialized
data:
drivers/net/usb/kalmia.c: In function ‘kalmia_bind’:
arch/x86/include/asm/string_32.h:78:22: error: ‘*((void *)ðernet_addr+4)’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
*((short *)to + 2) = *((short *)from + 2);
^
drivers/net/usb/kalmia.c:138:5: note: ‘*((void *)ðernet_addr+4)’ was declared here
This warning is harmless, but for consistency, we should make
the check for the return code match what the driver does everywhere
else and just progate it, which then gets rid of the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
usbnet:
- Remove stale new_mtu <= 0 check in usbnet.c
- Set min_mtu = 0, max_mtu = 65535 (sub-drivers must set their own
max_mtu and/or min_mtu as needed)
r8152:
- Set appropriate max_mtu for different variants (1500 or 9194)
lan78xx:
- Set max_mtu = 9000
asix_driver:
- max_mtu = 16384 for ax88178 variant
ax88179:
- max_mtu = 4088
cdc_ncm:
- max_mtu from hardware
cdc-phonet:
- min_mtu = 6, max_mtu = 65541
sierra_net:
- max_mtu = 1500, call usbnet_change_mtu directly
- sierra_net_change_mtu checked for MTU > 1500, then called
usbnet_change_mtu, but if we set max_mtu to let the network core handle
the range check, then we can simply call usbnet_change_mtu directly
smsc75xx:
- max_mtu = 9000
CC: netdev@vger.kernel.org
CC: Woojung Huh <woojung.huh@microchip.com>
CC: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
CC: Hayes Wang <hayeswang@realtek.com>
CC: Oliver Neukum <oneukum@suse.com>
CC: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the following four products of Lenovo and sort the order of the list.
VID PID
0x17ef 0x3062
0x17ef 0x3069
0x17ef 0x720c
0x17ef 0x7214
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check answers from USB stack and avoid re-sending the request
multiple times if the device does not respond.
This fixes the following problem, observed with a probably flaky adapter.
[62108.732707] usb 1-3: new high-speed USB device number 5 using xhci_hcd
[62108.914421] usb 1-3: New USB device found, idVendor=0b95, idProduct=7720
[62108.914463] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[62108.914476] usb 1-3: Product: AX88x72A
[62108.914486] usb 1-3: Manufacturer: ASIX Elec. Corp.
[62108.914495] usb 1-3: SerialNumber: 000001
[62114.109109] asix 1-3:1.0 (unnamed net_device) (uninitialized):
Failed to write reg index 0x0000: -110
[62114.109139] asix 1-3:1.0 (unnamed net_device) (uninitialized):
Failed to send software reset: ffffff92
[62119.109048] asix 1-3:1.0 (unnamed net_device) (uninitialized):
Failed to write reg index 0x0000: -110
...
Since the USB timeout is 5 seconds, and the operation is retried 30 times,
this results in
[62278.180353] INFO: task mtpd:1725 blocked for more than 120 seconds.
[62278.180373] Tainted: G W 3.18.0-13298-g94ace9e #1
[62278.180383] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
...
[62278.180957] kworker/2:0 D 0000000000000000 0 5744 2 0x00000000
[62278.180978] Workqueue: usb_hub_wq hub_event
[62278.181029] ffff880177f833b8 0000000000000046 ffff88017fd00000 ffff88017b126d80
[62278.181048] ffff880177f83fd8 ffff880065a71b60 0000000000013340 ffff880065a71b60
[62278.181065] 0000000000000286 0000000103b1c199 0000000000001388 0000000000000002
[62278.181081] Call Trace:
[62278.181092] [<ffffffff8e0971fd>] ? console_conditional_schedule+0x2c/0x2c
[62278.181105] [<ffffffff8e094f7b>] schedule+0x69/0x6b
[62278.181117] [<ffffffff8e0972e0>] schedule_timeout+0xe3/0x11d
[62278.181133] [<ffffffff8daadb1b>] ? trace_timer_start+0x51/0x51
[62278.181146] [<ffffffff8e095a05>] do_wait_for_common+0x12f/0x16c
[62278.181162] [<ffffffff8da856a7>] ? wake_up_process+0x39/0x39
[62278.181174] [<ffffffff8e095aee>] wait_for_common+0x52/0x6d
[62278.181187] [<ffffffff8e095b3b>] wait_for_completion_timeout+0x13/0x15
[62278.181201] [<ffffffff8de676ce>] usb_start_wait_urb+0x93/0xf1
[62278.181214] [<ffffffff8de6780d>] usb_control_msg+0xe1/0x11d
[62278.181230] [<ffffffffc037d629>] usbnet_write_cmd+0x9c/0xc6 [usbnet]
[62278.181286] [<ffffffffc03af793>] asix_write_cmd+0x4e/0x7e [asix]
[62278.181300] [<ffffffffc03afb41>] asix_set_sw_mii+0x25/0x4e [asix]
[62278.181314] [<ffffffffc03b001d>] asix_mdio_read+0x51/0x109 [asix]
...
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Quectel EC21 and EC25 need the same "set DTR" request as devices
based on the MDM9230 chipset, but has no USB3 support. Our best guess
is that the "set DTR" functionality depends on chipset and/or
baseband firmware generation. But USB3 is still an optional feature.
Since we cannot enable this unconditionally for all older devices, and
there doesn't appear to be anything we can use in the USB descriptors
to identify these chips, we are forced to use a device specific quirk
flag.
Reported-and-tested-by: Sebastian Sjoholm <sebastian.sjoholm@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
With centralized MTU checking, there's nothing productive done by
eth_change_mtu that isn't already done in dev_set_mtu, so mark it as
deprecated and remove all usage of it in the kernel. All callers have been
audited for calls to alloc_etherdev* or ether_setup directly, which means
they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu
prints out a netdev_warn about being deprecated, for the benefit of
out-of-tree drivers that might be utilizing it.
Of note, dvb_net.c actually had dev->mtu = 4096, while using
eth_change_mtu, meaning that if you ever tried changing it's mtu, you
couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set
to 4096 to remedy that.
v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable ALDPS and EEE to avoid the possible failure when setting the PHY.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the PHY relative settings together to hw_phy_cfg().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move enabling PHY to init(), otherwise some other settings may fail.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the following functions forward.
r8152_mmd_indirect()
r8152_mmd_read()
r8152_mmd_write()
r8152_eee_en()
r8152b_enable_eee()
r8153_eee_en()
r8153_enable_eee()
r8152b_enable_fc()
r8153_aldps_en()
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SOme statements in the driver only served to inform
which functions were entered. Ftrace can do that just as good without
needing memory. Remove the statements.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get a few warnings when building kernel with W=1:
drivers/net/usb/lan78xx.c:1182:6: warning: no previous prototype for 'lan78xx_defer_kevent' [-Wmissing-prototypes]
drivers/net/usb/lan78xx.c:1409:5: warning: no previous prototype for 'lan78xx_nway_reset' [-Wmissing-prototypes]
drivers/net/usb/lan78xx.c:2000:5: warning: no previous prototype for 'lan78xx_set_mac_addr' [-Wmissing-prototypes]
....
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more common logging style
Miscellanea:
o Add pr_fmt to prefix each output message
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macros that end in an underscore are just odd.
Add hso_dbg(level, fmt, ...) and use it everwhere instead.
Several uses had additional unnecessary newlines as the
macro added a newline. Remove the newline from the macro
and add newlines to each use as appropriate.
Remove now unused D<digit> macros.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The workqueue "pegasus_workqueue" queues a single work item per pegasus
instance and hence it doesn't require execution ordering. Hence,
alloc_workqueue has been used to replace the deprecated
create_singlethread_workqueue instance.
The WQ_MEM_RECLAIM flag has been set to ensure forward progress under
memory pressure since it's a network driver.
Since there are fixed number of work items, explicit concurrency
limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Petko Manolov <petkan@mip-labs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
check the coding style with checkpatch.pl and fix the warnings and errors.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Grant Grundler <grundler@chromium.org>
The miii_nway_restart() causes a PHY link change activity and
ax88772_link_reset will be called. link_reset will set
AX_CMD_WRITE_MEDIUM_MODE register correctly.
The asix_write_medium_mode in reset() fills in a default value to the register
which may be different from the negotiation result. So do this first.
Ignore the ret value since it's ignored in XXX_link_reset() functions.
Signed-off-by: Grant Grundler <grundler@google.com>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Grant Grundler <grundler@chromium.org>
https://lkml.org/lkml/2014/11/11/947
Ben Hutchings is correct. IEEE 802.3 spec section "22.2.4.1.1 Reset" requires
up to 500ms delay. Mitigate the "max" delay by polling the phy until BCM_RESET
bit is clear.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Allan Chou <allan@asix.com.tw>
The change fixes AX88772x resume failure by
- Restore incorrect AX88772A PHY registers when resetting
- Need to stop MAC operation when suspending
- Need to restart MII when restoring PHY
Signed-off-by: Allan Chou <allan@asix.com.tw>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Vincent Palatin <vpalatin@chromium.org>
Check the answers from the USB stack and avoid re-sending multiple times
the request if the device has disappeared.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Freddy Xin <freddy@asix.com.tw>
In order to R/W registers in suspend/resume functions, in_pm flags are
added to some functions to determine whether the nopm version of usb
functions is called.
Save BMCR and ANAR PHY registers in suspend function and restore them
in resume function.
Reset HW in resume function to ensure the PHY works correctly.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops. These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };
@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;
@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct ethtool_ops i = { ... };
// </smpl>
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the oops discovered by the Umap2 project and Alan Stern.
The intf member needs to be set before the firmware is downloaded.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Acked-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Unified UDP encapsulation offload methods for drivers, from
Alexander Duyck.
2) Make DSA binding more sane, from Andrew Lunn.
3) Support QCA9888 chips in ath10k, from Anilkumar Kolli.
4) Several workqueue usage cleanups, from Bhaktipriya Shridhar.
5) Add XDP (eXpress Data Path), essentially running BPF programs on RX
packets as soon as the device sees them, with the option to mirror
the packet on TX via the same interface. From Brenden Blanco and
others.
6) Allow qdisc/class stats dumps to run lockless, from Eric Dumazet.
7) Add VLAN support to b53 and bcm_sf2, from Florian Fainelli.
8) Simplify netlink conntrack entry layout, from Florian Westphal.
9) Add ipv4 forwarding support to mlxsw spectrum driver, from Ido
Schimmel, Yotam Gigi, and Jiri Pirko.
10) Add SKB array infrastructure and convert tun and macvtap over to it.
From Michael S Tsirkin and Jason Wang.
11) Support qdisc packet injection in pktgen, from John Fastabend.
12) Add neighbour monitoring framework to TIPC, from Jon Paul Maloy.
13) Add NV congestion control support to TCP, from Lawrence Brakmo.
14) Add GSO support to SCTP, from Marcelo Ricardo Leitner.
15) Allow GRO and RPS to function on macsec devices, from Paolo Abeni.
16) Support MPLS over IPV4, from Simon Horman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
xgene: Fix build warning with ACPI disabled.
be2net: perform temperature query in adapter regardless of its interface state
l2tp: Correctly return -EBADF from pppol2tp_getname.
net/mlx5_core/health: Remove deprecated create_singlethread_workqueue
net: ipmr/ip6mr: update lastuse on entry change
macsec: ensure rx_sa is set when validation is disabled
tipc: dump monitor attributes
tipc: add a function to get the bearer name
tipc: get monitor threshold for the cluster
tipc: make cluster size threshold for monitoring configurable
tipc: introduce constants for tipc address validation
net: neigh: disallow transition to NUD_STALE if lladdr is unchanged in neigh_update()
MAINTAINERS: xgene: Add driver and documentation path
Documentation: dtb: xgene: Add MDIO node
dtb: xgene: Add MDIO node
drivers: net: xgene: ethtool: Use phy_ethtool_gset and sset
drivers: net: xgene: Use exported functions
drivers: net: xgene: Enable MDIO driver
drivers: net: xgene: Add backward compatibility
drivers: net: phy: xgene: Add MDIO driver
...
The firmware in several ZTE devices (at least the MF823/831/910
modems/mifis) use OS fingerprinting to determine which type of device to
export. In addition, these devices export a REST API which can be used to
control the type of device. So far, on Linux, the devices have been seen as
RNDIS or CDC Ether.
When CDC Ether is used, devices of the same type are, as with RNDIS,
exported with the same, bogus random MAC address. In addition, the devices
(at least on all firmware revisions I have found) use the bogus MAC when
sending traffic routed from external networks. And as a final feature, the
devices sometimes export the link state incorrectly. There are also
references online to several other ZTE devices displaying this behavior,
with several different PIDs and MAC addresses.
This patch tries to improve the handling of ZTE devices by doing the
following:
* Create a new driver_info-struct that is used by ZTE devices that do not
have an explicit entry in the product table. This struct is the same as the
default cdc_ether driver info, but a new bind- and an rx_fixup-function
have been added.
* In the new bind function, we check if we have read a random MAC from the
device. If we have, then we generate a new random MAC address. This will
ensure that all devices get a unique MAC.
* The rx_fixup-function replaces the destination MAC address in the skb
with that of the device. I have not seen a revision of these devices that
behaves correctly (i.e., sets the right destination MAC), so I chose not to
do any comparison with for example the known, bogus addresses.
* The MF823/MF832/MF910 sometimes export cdc carrier on twice on connect
(the correct behavior is off then on). Work around this by manually setting
carrier to off if an on-notification is received and the NOCARRIER-bit is
not set.
This change will affect all devices, but it should take care of similar
mistakes made by other manufacturers. I tried to think of/look/test for
problems/regressions that could be introduced by this behavior, but could
not find any. However, my familiarity with this code path is not that
great, so there could be something I have overlooked.
I have tested this patch with multiple revisions of all three devices, and
they behave as expected. In other words, they all got a valid, random MAC,
the correct operational state and I can receive/sent traffic without
problems. I also tested with some other cdc_ether devices I have and did
not find any problems/regressions caused by the two general changes.
v3->v4:
* Forgot to remove unused variables, sorry about that (thanks David
Miller).
v2->v3:
* I had forgot to remove the random MAC generation from usbnet_cdc_bind()
(thanks Oliver).
* Rework logic in the ZTE bind-function a bit.
v1->v2:
* Only generate random MAC for ZTE devices (thanks Oliver Neukum).
* Set random MAC and do RX fixup for all ZTE devices that do not have a
product-entry, as the bogus MAC have been seen on devices with several
different PIDs/MAC addresses. In other words, it seems to be the default
behavior of ZTE CDC Ether devices (thanks Lars Melin).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the big USB driver update for 4.8-rc1. Lots of the normal stuff
in here, musb, gadget, xhci, and other updates and fixes. All of the
details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iFYEABECABYFAleVPioPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspB5AAnj7a
VJ2t2kcWzFUNQ6dyJrJCGGRAAKDZmb5CnOGeqJmdVpDzN1CGLYjfiw==
=47iA
-----END PGP SIGNATURE-----
Merge tag 'usb-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB driver update for 4.8-rc1. Lots of the normal
stuff in here, musb, gadget, xhci, and other updates and fixes. All
of the details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
cdc-acm: beautify probe()
cdc-wdm: use the common CDC parser
cdc-acm: cleanup error handling
cdc-acm: use the common parser
usbnet: move the CDC parser into USB core
usb: musb: sunxi: Simplify dr_mode handling
usb: musb: sunxi: make unexported symbols static
usb: musb: cppi41: add dma channel tracepoints
usb: musb: cppi41: move struct cppi41_dma_channel to header
usb: musb: cleanup cppi_dma header
usb: musb: gadget: add usb-request tracepoints
usb: musb: host: add urb tracepoints
usb: musb: add tracepoints to dump interrupt events
usb: musb: add tracepoints for register access
usb: musb: dsps: use musb register read/write wrappers instead
usb: musb: switch dev_dbg to tracepoints
usb: musb: add tracepoints support for debugging
usb: quirks: Add no-lpm quirk for Elan
phy: rcar-gen3-usb2: fix mutex_lock calling in interrupt
phy: rockhip-usb: use devm_add_action_or_reset()
...
The dependencies were impossible to handle preventing
drivers for CDC devices not which are not network drivers
from using the common parser.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices of the same type all export the same, random MAC address. This
behavior has been seen on the ZTE MF910, MF823 and MF831, and there are
probably more devices out there. Fix this by generating a valid random MAC
address if we read a random MAC from device.
Also, changed the memcpy() to ether_addr_copy(), as pointed out by
checkpatch.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool -i provides a driver version that is hard coded.
Export the same value via "modinfo".
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTL8153-AD supports a persistent system specific MAC address.
This means a device plugged into two different systems with host side
support will show different (but persistent) MAC addresses.
This information for the system's persistent MAC address is burned in when
the system HW is built and available under \_SB.AMAC in the DSDT at runtime.
This technology is currently implemented in the Dell TB15 and WD15 Type-C
docks. More information is available here:
http://www.dell.com/support/article/us/en/04/SLN301147
Signed-off-by: Mario Limonciello <mario_limonciello@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no conflict between the work_queue function and
rtl8152_set_speed(), so we don't have to cancel the delayed work in
rtl8152_set_speed().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 90186af404 ("r8152: fix lockup when runtime PM is enabled"),
the autoresume wouldn't start the device before rtl8152_open() is finished.
Therefore, we don't have to reset the linking status before and after
autoresume. That is, one of netif_carrier_off() in rtl8152_open() could be
removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rtl_hw_phy_work_func_t(), the flag of PHY_RESET is set in
rtl_ops.hw_phy_cfg() and cleared in rtl8152_set_speed(). Therefore,
the rtl_phy_reset() is never run and is unnecessary.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN_WAKE_EN is not used to determine if the device could support
WOL. It is used to signal a GPIO pin when a WOL event occurs. The WOL
still works even though it is disabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mellanox/mlx5/core/en.h
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
drivers/net/usb/r8152.c
All three conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTL8152 doesn't have U1U2 and U2P3 features, so use different
runtime functions for RTL812 and RTL8153 by adding autosuspend_en()
to rtl_ops.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several Lenovo users have reported problems with their Sierra
Wireless EM7455 modem. The driver has loaded successfully and
the MBIM management channel has appeared to work, including
establishing a connection to the mobile network. But no frames
have been received over the data interface.
The problem affects all EM7455 and MC7455, and is assumed to
affect other modems based on the same Qualcomm chipset and
baseband firmware.
Testing narrowed the problem down to what seems to be a
firmware timing bug during initialization. Adding a short sleep
while probing is sufficient to make the problem disappear.
Experiments have shown that 1-2 ms is too little to have any
effect, while 10-20 ms is enough to reliably succeed.
Reported-by: Stefan Armbruster <ml001@armbruster-it.de>
Reported-by: Ralph Plawetzki <ralph@purejava.org>
Reported-by: Andreas Fett <andreas.fett@secunet.com>
Reported-by: Rasmus Lerdorf <rasmus@lerdorf.com>
Reported-by: Samo Ratnik <samo.ratnik@gmail.com>
Reported-and-tested-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
LINK_OFF_WAKE_EN should be cleared after autoresume, otherwise after
system suspend, the system would wake up when linking off occurs.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When MTU is changed unlink_urbs() flushes RX Q but mean while usbnet_bh()
can fill up the Q at the same time.
Depends on which HCD is down there unlink takes long time then the flush
never ends.
Signed-off-by: Soohoon Lee <soohoon.lee@f5.com>
Reviewed-by: Kimball Murray <kmurray@f5.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
In set_speed(), BMCR_RESET would be set when the flag of PHY_RESET
is set. Use BMCR_RESET to replace testing the flag of PHY_RESET.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx early size should be
(agg_buf_sz - packet size) / 8
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset the BMU to clear the rx/tx fifo. This avoids that the unexpected
data remains in the hw.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable MAC clock speed down. It may casue the first control
transfer to contain the wrong data, when the power state change
from U1 to U0.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The user may change the speed. Use it to replace the default one.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move calling set_speed() from open() to rtl_hw_phy_work_func_t().
Then, we would set the default speed only for first initialization
or after resuming.
Besides, the set_speed() could handle the flag of PHY_RESET which
would be set in rtl_ops.hw_phy_cfg().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the settings of PHY to a work queue and schedule it after
rtl_ops.init().
There are some reasons for this. First, the settings are only
needed for the first time initialization or after the power
down occurs.
Second, the settings are independent with the others.
Last, the settings may take more time than the others. Leave
they in probe() or open() may delay the following flows.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace netdev_alloc_skb_ip_align() with napi_alloc_skb() which can save
several CPU cycles by avoiding having to disable and re-enable IRQs.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To detect link status up/down for connections where autonegotiation is
explicitly disabled, we don't get an irq but need to poll the status
register for link up/down detection.
This patch adds a workqueue to poll for link status.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If !count is true, count < 4 is also true.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch of
long-standing bugs in the tty layer and serial drivers as normal. Full
details in the shortlog.
All of these have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/0/oACgkQMUfUDdst+ynzyQCgsa54VNijdAzU6AA5HEfqmf2M
cGMAn1boH7hUWlAbJmzzihx4JASoGjYW
=V5VH
-----END PGP SIGNATURE-----
Merge tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver updates from Greg KH:
"Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch
of long-standing bugs in the tty layer and serial drivers as normal.
Full details in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (88 commits)
MAINTAINERS: 8250: remove website reference
serial: core: Fix port mutex assert if lockdep disabled
serial: 8250_dw: fix wrong logic in dw8250_check_lcr()
tty: vt, finish looping on duplicate
tty: vt, return error when con_startup fails
QE-UART: add "fsl,t1040-ucc-uart" to of_device_id
serial: mctrl_gpio: Drop support for out1-gpios and out2-gpios
serial: 8250dw: Add device HID for future AMD UART controller
Fix OpenSSH pty regression on close
serial: mctrl_gpio: add IRQ locking
serial: 8250: Integrate Fintek into 8250_base
serial: mps2-uart: add support for early console
serial: mps2-uart: add MPS2 UART driver
dt-bindings: document the MPS2 UART bindings
serial: sirf: Use generic uart-has-rtscts DT property
serial: sirf: Introduce helper variable struct device_node *np
serial: mxs-auart: Use generic uart-has-rtscts DT property
serial: imx: Use generic uart-has-rtscts DT property
doc: DT: Add Generic Serial Device Tree Bindings
serial: 8250: of: Make tegra_serial_handle_break() static
...
Use kmemdup when some other buffer is immediately copied into allocated
region. It replaces call to allocation followed by memcpy, by a single
call to kmemdup.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation updates the mtu size and notify cdc_ncm
device using USB_CDC_SET_MAX_DATAGRAM_SIZE request about datagram
size change instead of changing rx_urb_size.
Whenever mtu is being changed, datagram size should also be
updated. Also updating maxmtu formula so it takes max_datagram_size with
use of cdc_ncm_max_dgram_size() and not ctx.
Signed-off-by: Robert Dobrowolski <robert.dobrowolski@linux.intel.com>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(!count || count < 4) is always true.
So let's remove the coding which is dead at least since 2005.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In testing with HiKey, we found that since
commit 3f30b158eb ("asix: On RX avoid creating bad Ethernet
frames"),
we're seeing lots of noise during network transfers:
[ 239.027993] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.037310] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x54ebb5ec, offset 4
[ 239.045519] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0xcdffe7a2, offset 4
[ 239.275044] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.284355] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x1d36f59d, offset 4
[ 239.292541] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0xaef3c1e9, offset 4
[ 239.518996] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.528300] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x2881912, offset 4
[ 239.536413] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x5638f7e2, offset 4
And network throughput ends up being pretty bursty and slow with
a overall throughput of at best ~30kB/s (where as previously we
got 1.1MB/s with the slower USB1.1 "full speed" host).
We found the issue also was reproducible on a x86_64 system,
using a "high-speed" USB2.0 port but the throughput did not
measurably drop (possibly due to the scp transfer being cpu
bound on my slow test hardware).
After lots of debugging, I found the check added in the
problematic commit seems to be calculating the offset
incorrectly.
In the normal case, in the main loop of the function, we do:
(where offset is zero, or set to "offset += (copy_length + 1) &
0xfffe" in the previous loop)
rx->header = get_unaligned_le32(skb->data +
offset);
offset += sizeof(u32);
But the problematic patch calculates:
offset = ((rx->remaining + 1) & 0xfffe) + sizeof(u32);
rx->header = get_unaligned_le32(skb->data + offset);
Adding some debug logic to check those offset calculation used
to find rx->header, the one in problematic code is always too
large by sizeof(u32).
Thus, this patch removes the incorrect " + sizeof(u32)" addition
in the problematic calculation, and resolves the issue.
Cc: Dean Jenkins <Dean_Jenkins@mentor.com>
Cc: "David B. Robins" <linux@davidrobins.net>
Cc: Mark Craske <Mark_Craske@mentor.com>
Cc: Emil Goode <emilgoode@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Ivan Vecera <ivecera@redhat.com>
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: stable <stable@vger.kernel.org> #4.4+
Reported-by: Yongqin Liu <yongqin.liu@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the call to fn() fails then "buf" is uninitialized. Just return the
error code in that case.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the fn() calls fail then "buf" is uninitialized. Just return early
in that situation.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
This takes the MAC address for smsc75xx/smsc95xx USB network devices
from a the device tree. This is required to get a usable persistent
address on the popular beagleboard, whose hardware designers
accidentally forgot that an ethernet device really requires an a
MAC address to be functional.
The Raspberry Pi also ships smsc9514 without a serial EEPROM, stores
the MAC address in ROM accessible via VC4 firmware.
The smsc75xx and smsc95xx drivers are just two copies of the
same code, so better fix both.
[lkundrak@v3.sk: updated to use of_get_property() as per suggestion from
Arnd, reworded the message and comments a bit]
Tested-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Abstract TTY_THROTTLED bit tests with tty_throttled().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default Pegasus setup was to append the status and CRC at the end of each
received packet. The status bits are used to update various stats, but CRC has
been ignored. The new default is to not append CRC at the end of RX packets.
Signed-off-by: Petko Manolov <petkan@mip-labs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
usb_fill_bulk_urb() receives buffer length parameter 8 bytes larger
than what's allocated by alloc_skb(); This seems to be a problem with
older (pegasus usb-1.1) devices, which may silently return more data
than the maximal packet length.
Reported-by: Lincoln Ramsay <a1291762@gmail.com>
Signed-off-by: Petko Manolov <petkan@mip-labs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At forced 100 Full & Half duplex mode, chip may fail to set mode correctly
when cable is switched between long(~50+m) and short one.
As workaround, set to 10 before setting to 100 at forced 100 F/H mode.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix rx_bytes, tx_bytes and tx_frames error in netdev.stats.
- rx_bytes counted bytes excluding size of struct ethhdr.
- tx_packets didn't count multiple packets in a single urb
- tx_bytes included 8 bytes of extra commands.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now have a positive report of another Huawei device needing
this quirk: The ME906s-158 (12d1:15c1). This is an m.2 form
factor modem with no obvious relationship to the E3372 (12d1:157d)
we already have a quirk entry for. This is reason enough to
believe the quirk might be necessary for any number of current
and future Huawei devices.
Applying the quirk to all Huawei devices, since it is crucial
to any device affected by the firmware bug, while the impact
on non-affected devices is negligible.
The quirk can if necessary be disabled per-device by writing
N to /sys/class/net/<iface>/cdc_ncm/ndp_to_end
Reported-by: Andreas Fett <andreas.fett@secunet.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Telit LE910 V2 is a mobile broadband card with no ARP capabilities:
the patch makes this device to use wwan_noarp_info struct
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit a59f8c5b04.
There are several bugs in this new code, for example:
1) Uses sleeping locks in get_stats64, which is not allowed,
as the operation can be invoked in an atomic context.
2) Uses PM fields without CONFIG_PM or similar guards.
3) Does not synchronize HW stats when the device runtime
suspends.
Therefore this is being reverted until a correct version
is implemented.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add lan78xx_get_stats64 of ndo_get_stats64 to report
all statistics counters including errors from HW statistics.
Read from HW when auto suspend is disabled, use saved counter when
auto suspend is enabled because periodic call to ndo_get_stats64
prevents USB auto suspend.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update to handle statistics counter rollover.
Check statistics counter periodically and compensate it when
counter value rolls over at max (20 or 32bits).
Simple mechanism adjusts monitoring timer to allow USB auto suspend.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for Gemalto's Cinterion PHxx WWAN interfaces
by adding QMI_FIXED_INTF with Cinterion's VID and PID.
PHxx can have:
2 RmNet Interfaces (PID 0x0082) or
1 RmNet + 1 USB Audio interface (PID 0x0083).
Signed-off-by: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
usbnet_link_change will call schedule_work and should be
avoided if bind is failing. Otherwise we will end up with
scheduled work referring to a netdev which has gone away.
Instead of making the call conditional, we can just defer
it to usbnet_probe, using the driver_info flag made for
this purpose.
Fixes: 8a34b0ae87 ("usbnet: cdc_ncm: apply usbnet_link_change")
Reported-by: Andrey Konovalov <andreyknvl@gmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices will silently fail setup unless they are reset first.
This is necessary even if the data interface is already in
altsetting 0, which it will be when the device is probed for the
first time. Briefly toggling the altsetting forces a function
reset regardless of the initial state.
This fixes a setup problem observed on a number of Huawei devices,
appearing to operate in NTB-32 mode even if we explicitly set them
to NTB-16 mode.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case bind() works, but a later error forces bailing
in probe() in error cases work and a timer may be scheduled.
They must be killed. This fixes an error case related to
the double free reported in
http://www.spinics.net/lists/netdev/msg367669.html
and needs to go on top of Linus' fix to cdc-ncm.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Used to be allocated and required freeing, but now
priv->mdio->irq is now a fixed sized array and should no longer be
free'd.
Issue detected using static analysis with CoverityScan
Fixes: e7f4dc3536 ("mdio: Move allocation of interrupts into core")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MC74xx and EM74xx modules use different IDs by default, according
to the Lenovo EM7455 driver for Windows.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool operations of set_pauseram and get_pauseparm.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not required after commit cd772de358
("phy: keep pause flags in phy driver features")
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace devid to chipid & chiprev for easy access.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids a harmless randconfig warning I get when USB_NET_CDC_SUBSET
is enabled, but all of the more specific drivers are not:
drivers/net/usb/cdc_subset.c:241:2: #warning You need to configure some hardware for this driver
The current behavior is clearly intentional, giving a warning when
a user picks a configuration that won't do anything good. The only
reason for even addressing this is that I'm getting close to
eliminating all 'randconfig' warnings on ARM, and this came up
a couple of times.
My workaround is to not even build the module when none of the
configurations are enable.
Alternatively we could simply remove the #warning (nothing wrong
for compile-testing), turn it into a runtime warning, or
change the Kconfig options into a menu to hide CONFIG_USB_NET_CDC_SUBSET.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Throttle TX path only at slower than SuperSpeed USB.
SuperSpeed USB has enough bandwidth to maintain GigE.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depends on chip, some EEPROM pins are muxed with LED function.
Disable & restore LED function to access EEPROM.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update lan78xx to use patch of commit 4f2aaf7dd9
("Merge branch 'fix-phy-ignore-interrupts'").
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_main.c
drivers/net/ethernet/mellanox/mlxsw/spectrum.h
drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
The bond_main.c and mellanox switch conflicts were cases of
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
SIMCom 7230E is a QMI LTE module with support for most "normal" bands.
Manual testing has showed that only interface five works.
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The union descriptor must be checked. Its usage was conditional
before the parser was introduced. This is important, because
many RNDIS device, which also use the common parser, have
bogus extra descriptors.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Tested-by: Vasily Galkin <galkin-vv@yandex.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace disable_aldps() and enable_aldps() with aldps_en().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace test_bit() followed by clear_bit() with test_and_clear_bit().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the autosuspend is enabled and occurs before system suspend, we should
wake the device before running system syspend. Then, we could change the wake
event for system suspend. Otherwise, the device would resume the system when
receiving any packet.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug writing to EEPROM in lan78xx_ethtool_set_eeprom()
when asked to write to OTP.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The WeTelecom-WPD600N is an LTE module that, in addition to supporting most
"normal" bands, also supports LTE over 450MHz. Manual testing showed that
only interface number three replies to QMI messages.
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the reset_resume() is called, the flag of SELECTIVE_SUSPEND should be
cleared and reinitialize the device, whether the SELECTIVE_SUSPEND is set
or not. If reset_resume() is called, it means the power supply is cut or the
device is reset. That is, the device wouldn't be in runtime suspend state and
the reinitialization is necessary.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NCM buffer sizes are negotiated with the device independently of
the network device MTU. The RX buffers are allocated by the
usbnet framework based on the rx_urb_size value set by cdc_ncm. A
single RX buffer can hold a number of MTU sized packets.
The default usbnet change_mtu ndo only modifies rx_urb_size if it
is equal to hard_mtu. And the cdc_ncm driver will set rx_urb_size
and hard_mtu independently of each other, based on dwNtbInMaxSize
and dwNtbOutMaxSize respectively. It was therefore assumed that
usbnet_change_mtu() would never touch rx_urb_size. This failed to
consider the case where dwNtbInMaxSize and dwNtbOutMaxSize happens
to be equal.
Fix by implementing an NCM specific change_mtu ndo, modifying the
netdev MTU without touching the buffer size settings.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike DW5550, Dell DW5813 is a mobile broadband card with no ARP
capabilities: the patch makes this device to use wwan_noarp_info struct
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike DW5550, Dell DW5812 is a mobile broadband card with no ARP
capabilities: the patch makes this device to use wwan_noarp_info struct
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it is possible for an external system to send oversize packets
at anytime, it is best for driver not to print a message and spam
the log (potential external DoS).
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=109471
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
The CDC descriptors found on these vendor specific functions should
not be considered authoritative. They seem to be ignored by drivers
for other systems, and the quality is therefore low.
One device (1e0e:9001) has been reported to have such a bogus union
descriptor on the QMI function, making it fail probing even if the
device id was dynamically added. The report was not complete enough
to allow adding a device entry for this modem. But this should at
least fix the dynamic id probing problem.
Reported-by: Kanerva Topi <Topi.Kanerva@cinia.fi>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an interface is brought up which was previously suspended (via
runtime PM), it would hang. This happens because napi_disable is called
before napi_enable.
Solve this by avoiding napi_enable in the resume during open function
(netif_running is true when open is called, IFF_UP is set after a
successful open; netif_running is false when close is called, but IFF_UP
is then still set).
While at it, remove WORK_ENABLE check from rtl8152_open (introduced with
the original change) because it cannot happen:
- After this patch, runtime resume will not set it during rtl8152_open.
- When link is up, rtl8152_open is not called.
- When link is down during system/auto suspend/resume, it is not set.
Fixes: 41cec84cf2 ("r8152: don't enable napi before rx ready")
Link: https://lkml.kernel.org/r/20151205105912.GA1766@al
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a writable sysfs attribute for the "NDP to end"
quirk flag.
This makes it easier for end users to test new devices for
this firmware bug. We've been lucky so far, but we should
not depend on reporters capable of rebuilding the driver.
Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The notifier calls were thrown in as a last-minute fix for an
imagined "this device could be part of a bridge" problem. That
revealed a certain lack of locking. Not to mention testing...
Avoid this splat:
RTNL: assertion failed at net/core/dev.c (1639)
CPU: 0 PID: 4293 Comm: bash Not tainted 4.4.0-rc3+ #358
Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011
0000000000000000 ffff8800ad253d60 ffffffff8122f7cf ffff8800ad253d98
ffff8800ad253d88 ffffffff813833ab 0000000000000002 ffff880230f48560
ffff880230a12900 ffff8800ad253da0 ffffffff813833da 0000000000000002
Call Trace:
[<ffffffff8122f7cf>] dump_stack+0x4b/0x63
[<ffffffff813833ab>] call_netdevice_notifiers_info+0x3d/0x59
[<ffffffff813833da>] call_netdevice_notifiers+0x13/0x15
[<ffffffffa09be227>] raw_ip_store+0x81/0x193 [qmi_wwan]
[<ffffffff8131e149>] dev_attr_store+0x20/0x22
[<ffffffff811d858b>] sysfs_kf_write+0x49/0x50
[<ffffffff811d8027>] kernfs_fop_write+0x10a/0x151
[<ffffffff8117249a>] __vfs_write+0x26/0xa5
[<ffffffff81085ed4>] ? percpu_down_read+0x53/0x7f
[<ffffffff81174c9e>] ? __sb_start_write+0x5f/0xb0
[<ffffffff81174c9e>] ? __sb_start_write+0x5f/0xb0
[<ffffffff81172c37>] vfs_write+0xa3/0xe7
[<ffffffff811734ad>] SyS_write+0x50/0x7e
[<ffffffff8145c517>] entry_SYSCALL_64_fastpath+0x12/0x6f
Fixes: 32f7adf633 ("net: qmi_wwan: support "raw IP" mode")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Huawei E3372 (12d1:157d) needs this quirk in MBIM mode
as well. Allow this by forcing the NTB to contain only a
single NDP, and add a device specific entry for this ID.
Due to the way Huawei use device IDs, this might be applied
to other modems as well. It is assumed that those modems
will be based on the same firmware and will need this quirk
too. If not, it will still not harm normal usage, although
multiplexing performance could be impacted.
Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Reported-by: Sami Farin <hvtaifwkbgefbaei@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-By: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QMI wwan devices have traditionally emulated ethernet devices
by default. But they have always had the capability of operating
without any L2 header at all, transmitting and receiving "raw"
IP packets over the USB link. This firmware feature used to be
configurable through the QMI management protocol.
Traditionally there was no way to verify the firmware mode
without attempting to change it. And the firmware would often
disallow changes anyway, i.e. due to a session already being
established. In some cases, this could be a hidden firmware
internal session, completely outside host control. For these
reasons, sticking with the "well known" default mode was safest.
But newer generations of QMI hardware and firmware have moved
towards defaulting to "raw IP" mode instead, followed by an
increasing number of bugs in the already buggy "802.3" firmware
implementation. At the same time, the QMI management protocol
gained the ability to detect the current mode. This has enabled
the userspace QMI management application to verify the current
firmware mode without trying to modify it.
Following this development, the latest QMI hardware and firmware
(the MDM9x30 generation) has dropped support for "802.3" mode
entirely. Support for "raw IP" framing in the driver is therefore
necessary for these devices, and to a certain degree to work
around problems with the previous generation,
This patch adds support for "raw IP" framing for QMI devices,
changing the netdev from an ethernet device to an ARPHRD_NONE
p-t-p device when "raw IP" framing is enabled.
The firmware setup is fully delegated to the QMI userspace
management application, through simple tunneling of the QMI
protocol. The driver will therefore not know which mode has been
"negotiated" between firmware and userspace. Allowing userspace
to inform the driver of the result through a sysfs switch is
considered a better alternative than to change the well established
clean delegation of firmware management to userspace.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assume the minidriver has taken care of all L2 header parsing
if it sets skb->protocol. This allows the minidriver to
support non-ethernet L2 headers, and even operate without
any L2 header at all.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This turned out to be a bootloader device ID. No need for
that in this driver. It will only provide a single serial
function.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDM9x30 based modems appear to go into a deeper sleep when
suspended without "Remote Wakeup" enabled. The QMI interface
will not respond unless a "set DTR" control request is sent
on resume. The effect is similar to a QMI_CTL SYNC request,
resetting (some of) the firmware state.
We allow userspace sessions to span multiple character device
open/close sequences. This means that userspace can depend
on firmware state while both the netdev and the character
device are closed. We have disabled "needs_remote_wakeup" at
this point to allow devices without remote wakeup support to
be auto-suspended.
To make sure the MDM9x30 keeps firmware state, we need to
keep "needs_remote_wakeup" always set. We also need to
issue a "set DTR" request to enable the QMI interface.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 77b0a09967 ("cdc-ncm: use common parser") added a dangerous
new trust in the CDC functional descriptors presented by the device,
unconditionally assuming that any device handled by the driver has
a CDC Union descriptor.
This descriptor is required by the NCM and MBIM specs, but crashing
on non-compliant devices is still unacceptable. Not only will that
allow malicious devices to crash the kernel, but in this case it is
also well known that there are non-compliant real devices on the
market - as shown by the comment accompanying the IAD workaround
in the same function.
The Sierra Wireless EM7305 is an example of such device, having
a CDC header and a CDC MBIM descriptor but no CDC Union:
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 12
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 14
bInterfaceProtocol 0
iInterface 0
CDC Header:
bcdCDC 1.10
CDC MBIM:
bcdMBIMVersion 1.00
wMaxControlMessage 4096
bNumberFilters 16
bMaxFilterSize 128
wMaxSegmentSize 4064
bmNetworkCapabilities 0x20
8-byte ntb input size
Endpoint Descriptor:
..
The conversion to a common parser also left the local cdc_union
variable untouched. This caused the IAD workaround code to be applied
to all devices with an IAD descriptor, which was never intended. Finish
the conversion by testing for hdr.usb_cdc_union_desc instead.
Cc: Oliver Neukum <oneukum@suse.com>
Fixes: 77b0a09967 ("cdc-ncm: use common parser")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas reports
"
4gsystems sells two total different LTE-surfsticks under the same name.
..
The newer version of XS Stick W100 is from "omega"
..
Under windows the driver switches to the same ID, and uses MI03\6 for
network and MI01\6 for modem.
..
echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id
echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1c9e ProdID=9b01 Rev=02.32
S: Manufacturer=USB Modem
S: Product=USB Modem
S: SerialNumber=
C: #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
Now all important things are there:
wwp0s29f7u2i3 (net), ttyUSB2 (at), cdc-wdm0 (qmi), ttyUSB1 (at)
There is also ttyUSB0, but it is not usable, at least not for at.
The device works well with qmi and ModemManager-NetworkManager.
"
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Dell DW5580 is a 3G modem, this patch adds the device as a
mobile broadband adapter
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge final patch-bomb from Andrew Morton:
"Various leftovers, mainly Christoph's pci_dma_supported() removals"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
pci: remove pci_dma_supported
usbnet: remove ifdefed out call to dma_supported
kaweth: remove ifdefed out call to dma_supported
sfc: don't call dma_supported
nouveau: don't call pci_dma_supported
netup_unidvb: use pci_set_dma_mask insted of pci_dma_supported
cx23885: use pci_set_dma_mask insted of pci_dma_supported
cx25821: use pci_set_dma_mask insted of pci_dma_supported
cx88: use pci_set_dma_mask insted of pci_dma_supported
saa7134: use pci_set_dma_mask insted of pci_dma_supported
saa7164: use pci_set_dma_mask insted of pci_dma_supported
tw68-core: use pci_set_dma_mask insted of pci_dma_supported
pcnet32: use pci_set_dma_mask insted of pci_dma_supported
lib/string.c: add ULL suffix to the constant definition
hugetlb: trivial comment fix
selftests/mlock2: add ULL suffix to 64-bit constants
selftests/mlock2: add missing #define _GNU_SOURCE
This device has same vendor and product IDs as G2K devices, but it has
different number of interfaces(4 vs 5) and also different interface
layout where EC20 has QMI on interface 4 instead of 0.
lsusb output:
Bus 002 Device 003: ID 05c6:9215 Qualcomm, Inc. Acer Gobi 2000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x05c6 Qualcomm, Inc.
idProduct 0x9215 Acer Gobi 2000 Wireless Modem
bcdDevice 2.32
iManufacturer 1 Quectel
iProduct 2 Quectel LTE Module
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 209
bNumInterfaces 5
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 500mA
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in net/ipv4/ipmr.c, in 'net' we were
fixing the "BH-ness" of the counter bumps whilst in 'net-next'
the functions were modified to take an explicit 'net' parameter.
Signed-off-by: David S. Miller <davem@davemloft.net>
The lt4112 is a HP branded Huawei me906e modem. Like other Huawei
modems, it does not have a fixed interface to function mapping.
Instead it uses a Huawei specific scheme: functions are mapped by
subclass and protocol.
However, the HP vendor ID is used for modems from many different
manufacturers using different schemes, so we cannot apply a generic
vendor rule like we do for the Huawei vendor ID.
Replace the previous lt4112 entry pointing to an arbitrary interface
number with a device specific subclass + protocol match.
Reported-and-tested-by: Muri Nicanor <muri+libqmi@immerda.ch>
Tested-by: Martin Hauke <mardnh@gmx.de>
Fixes: bb2bdeb83f ("qmi_wwan: Add support for HP lt4112 LTE/HSPA+ Gobi 4G Modem")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
New device IDs shamelessly lifted from the vendor driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Just another AX88178-based 10/100/1000 USB-to-Ethernet dongle. This one
shows up in lsusb as: "ID 08dd:0114 Billionton Systems, Inc".
Signed-off-by: Chia-Sheng Chang <changchias@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Christoph Jaeger <cj@linux.com>
Cc: "Woojung.Huh@microchip.com" <Woojung.Huh@microchip.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Markus Elfring <elfring@users.sourceforge.net>
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: netdev@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid a loss of synchronisation of the Ethernet Data header 32-bit
word due to a failure to get a netdev socket buffer.
The ASIX RX handling algorithm returned 0 upon a failure to get
an allocation of a netdev socket buffer. This causes the URB
processing to stop which potentially causes a loss of synchronisation
with the Ethernet Data header 32-bit word. Therefore, subsequent
processing of URBs may be rejected due to a loss of synchronisation.
This may cause additional good Ethernet frames to be discarded
along with outputting of synchronisation error messages.
Implement a solution which checks whether a netdev socket buffer
has been allocated before trying to copy the Ethernet frame into
the netdev socket buffer. But continue to process the URB so that
synchronisation is maintained. Therefore, only a single Ethernet
frame is discarded when no netdev socket buffer is available.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RX Ethernet frames span multiple URB socket buffers,
the data stream may suffer a discontinuity which will cause
the current Ethernet frame in the netdev socket buffer
to be incomplete. This frame needs to be discarded instead
of appending unrelated data from the current URB socket buffer
to the Ethernet frame in the netdev socket buffer. This avoids
creating a corrupted Ethernet frame in the netdev socket buffer.
A discontinuity can occur when the previous URB socket buffer
held an incomplete Ethernet frame due to truncation or a
URB socket buffer containing the end of the Ethernet frame
was missing.
Therefore, add a sanity test for when an Ethernet frame
spans multiple URB socket buffers to check that the remaining
bytes of the currently received Ethernet frame point to
a good Data header 32-bit word of the next Ethernet
frame. Upon error, reset the remaining bytes variable to
zero and discard the current netdev socket buffer.
Assume that the Data header is located at the start of
the current socket buffer and attempt to process the next
Ethernet frame from there. This avoids unnecessarily
discarding a good URB socket buffer that contains a new
Ethernet frame.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code is checking that the Ethernet frame will fit into a
netdev allocated socket buffer within the constraints of MTU size,
Ethernet header length plus VLAN header length.
The original code was checking rx->remaining each loop of the while
loop that processes multiple Ethernet frames per URB and/or Ethernet
frames that span across URBs. rx->remaining decreases per while loop
so there is no point in potentially checking multiple times that the
Ethernet frame (remaining part) will fit into the netdev socket buffer.
The modification checks that the size of the Ethernet frame will fit
the netdev socket buffer before allocating the netdev socket buffer.
This avoids grabbing memory and then deciding that the Ethernet frame
is too big and then freeing the memory.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tidy-up the Data header 32-bit word synchronisation logic in
asix_rx_fixup_internal() by removing redundant logic tests.
The code is looking at the following cases of the Data header
32-bit word that is present before each Ethernet frame:
a) all 32 bits of the Data header word are in the URB socket buffer
b) first 16 bits of the Data header word are at the end of the URB
socket buffer
c) last 16 bits of the Data header word are at the start of the URB
socket buffer eg. split_head = true
Note that the lifetime of rx->split_head exists outside of the
function call and is accessed per processing of each URB. Therefore,
split_head being true acts on the next URB to be processed.
To check for b) the offset will be 16 bits (2 bytes) from the end of
the buffer then indicate split_head is true.
To check for c) split_head must be true because the first 16 bits
have been found.
To check for a) else c)
Note that the || logic of the old code included the state
(skb->len - offset == sizeof(u16) && rx->split_head) which is not
possible because the split_head cannot be true whilst checking for b).
This is because the split_head indicates that the first 16 bits have
been found and that is not possible whilst checking for the first 16
bits. Therefore simplify the logic.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Data header synchronisation is easier to understand
if the variables "remaining" and "size" are renamed.
Therefore, the lifetime of the "remaining" variable exists
outside of asix_rx_fixup_internal() and is used to indicate
any remaining pending bytes of the Ethernet frame that need
to be obtained from the next socket buffer. This allows an
Ethernet frame to span across multiple socket buffers.
"size" is now local to asix_rx_fixup_internal() and contains
the size read from the Data header 32-bit word.
Add "copy_length" to hold the number of the Ethernet frame
bytes (maybe a part of a full frame) that are to be copied
out of the socket buffer.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If asix_rx_fixup_internal() fails to allocate rx->ax_skb, it will return
but not clear rx->size. rx points to driver private data. A later call
assumes that nonzero size means ax_skb was allocated and passes a null
ax_skb to skb_put. Changed allocation failure return to clear size first.
Found testing board with AX88772B devices.
Signed-off-by: David B. Robins <linux@davidrobins.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan78xx_suspend() may return non-zero from lan78xx_write_reg() in some scenario.
Fix to return 0 when lan78xx_suspend() has no error.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/arp.c
The net/ipv4/arp.c conflict was one commit adding a new
local variable while another commit was deleting one.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 12fd84f438 ("ipv6: Remove unused neigh argument for
icmp6_dst_alloc() and its callers."), the neigh parameter of ndisc_send_na
and ndisc_send_ns is unused.
CC: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts the ch9200 driver to use the module_usb_driver() macro which
makes the code smaller and a bit simpler.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->len is always non-negative.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a bunch of cheap USB 10/100 devices based on QinHeng chipsets. The
vendor driver supports the CH9100 and CH9200 devices, but the majority of
the code is of the if (ch9100) {} else {} form, with the most significant
difference being that CH9200 provides a real MII interface but CH9100 fakes
one with a bunch of global variables and magic commands. I don't have a
CH9100, so it's probably better if someone who does provides an independent
driver for it. In any case, this is a lightly cleaned up version of the
vendor driver with all the CH9100 code dropped.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove not defined MAC_CR_GMII_EN_ bit from MAC_CR.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create lan78xx_get_mdix_status() and lan78xx_set_mdix_status() for MDIX control.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove phy defines in lan78xx.h and use defines in include/linux/microchipphy.h.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update to use phylib instead of mii_if_info.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PHYLIB and MICROCHIP_PHY as default configuration for lan78xx.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check device ready bit (PMT_CTL_READY_) after reset the PHY.
Device may not be ready even if PHY_RST_ is cleared depends on configuration.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix build error caused by missing Kconfig dependency:
ERROR: "cdc_parse_cdc_header" [drivers/net/usb/cdc-phonet.ko] undefined!
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves cdc-phonet to the common parser for CDC users
to reduce code duplication.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves qmi-wwan to the common parser for CDC user
to reduce code duplication.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses the common parser to parse extra CDC
headers in order to reduce code duplication.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves cdc-ncm to the common parser for CDC user
to reduce code duplication.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CDC drivers all implement their own parser for the extra headers.
This patch fixes the code duplication introducing a single common
parser in usbnet.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the runtime suspend issues result from the linking change.
Case 1:
a) link down occurs.
b) driver disable tx/rx.
c) autosuspend occurs.
d) hw linking up.
e) device suspends without enabling tx/rx.
f) couldn't wake up when receiving packets.
Case 2:
a) Nway results in linking down.
b) autosuspend occurs.
c) device suspends.
d) device may not wake up when linking up.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split DRIVER_VERSION into NETNEXT_VERSION and NET_VERSION. Then,
according to the value of DRIVER_VERSION, we could know which
patches are used generally without comparing the source code.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The race may happen when a device (e.g. YOTA 4G LTE Modem) is
unplugged while the system is downloading a large file from the Net.
Hardware breakpoints and Kprobes with delays were used to confirm that
the race does actually happen.
The race is on skb_queue ('next' pointer) between usbnet_stop()
and rx_complete(), which, in turn, calls usbnet_bh().
Here is a part of the call stack with the code where the changes to the
queue happen. The line numbers are for the kernel 4.1.0:
*0 __skb_unlink (skbuff.h:1517)
prev->next = next;
*1 defer_bh (usbnet.c:430)
spin_lock_irqsave(&list->lock, flags);
old_state = entry->state;
entry->state = state;
__skb_unlink(skb, list);
spin_unlock(&list->lock);
spin_lock(&dev->done.lock);
__skb_queue_tail(&dev->done, skb);
if (dev->done.qlen == 1)
tasklet_schedule(&dev->bh);
spin_unlock_irqrestore(&dev->done.lock, flags);
*2 rx_complete (usbnet.c:640)
state = defer_bh(dev, skb, &dev->rxq, state);
At the same time, the following code repeatedly checks if the queue is
empty and reads these values concurrently with the above changes:
*0 usbnet_terminate_urbs (usbnet.c:765)
/* maybe wait for deletions to finish. */
while (!skb_queue_empty(&dev->rxq)
&& !skb_queue_empty(&dev->txq)
&& !skb_queue_empty(&dev->done)) {
schedule_timeout(msecs_to_jiffies(UNLINK_TIMEOUT_MS));
set_current_state(TASK_UNINTERRUPTIBLE);
netif_dbg(dev, ifdown, dev->net,
"waited for %d urb completions\n", temp);
}
*1 usbnet_stop (usbnet.c:806)
if (!(info->flags & FLAG_AVOID_UNLINK_URBS))
usbnet_terminate_urbs(dev);
As a result, it is possible, for example, that the skb is removed from
dev->rxq by __skb_unlink() before the check
"!skb_queue_empty(&dev->rxq)" in usbnet_terminate_urbs() is made. It is
also possible in this case that the skb is added to dev->done queue
after "!skb_queue_empty(&dev->done)" is checked. So
usbnet_terminate_urbs() may stop waiting and return while dev->done
queue still has an item.
Locking in defer_bh() and usbnet_terminate_urbs() was revisited to avoid
this race.
Signed-off-by: Eugene Shatokhin <eugene.shatokhin@rosalab.ru>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/usb/lan78xx.c: In function ‘lan78xx_link_reset’:
net/usb/lan78xx.c:1107: warning: comparison is always false due to limited range of data type
net/usb/lan78xx.c:1111: warning: comparison is always false due to limited range of data type
Assigning return values that can be negative error codes to "u16"
variables makes them positive, ignoring the errors. Hence use "int"
instead.
Drop the "unlikely"s (unlikely considered harmful) and propagate the
actual error values instead of overriding them to -EIO while we're at
it.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other Sierra Wireless MC73xx devices exist, with different USB IDs.
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is needed to check EVENT_NO_RUNTIME_PM bit of dev->flags in
usbnet_stop(), but its value should be read before it is cleared
when dev->flags is set to 0.
The problem was spotted and the fix was provided by
Oliver Neukum <oneukum@suse.de>.
Signed-off-by: Eugene Shatokhin <eugene.shatokhin@rosalab.ru>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The UEFI driver would enable zero length, and the Linux driver doesn't
need it. Zero length let the hw complete the transfer with length 0,
when there is no received packet. It would add the load of USB host
controller and reduce the performance.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Repost patch of driver for LAN7800 family of USB 2.0 & USB 3.0 to Gigabit Ethernet.
- remove module param which can be configurable by standard mechanism.
- remove other module parms except msg_level per review comment.
- update to handle byte swap for statistics structure correctly.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device reset is necessary if the hw becomes abnormal and stops
transmitting packets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rtl8152_pre_reset() and rtl8152_post_reset() which are used when
calling usb_reset_device(). The two functions could reduce the time
of reset when calling usb_reset_device() after probe().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust napi_disable() and napi_enable() to avoid r8152_poll() start
working before rx ready. Otherwise, it may have race condition for
rx_agg.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid the driver to enable WOL if the device doesn't support it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Disable U1/U2 during initialization.
- Disable lpm when linking is on, and enable it when linking is off.
- Disable U1/U2 when enabling runtime suspend.
It is possible to let hw stop working, if the U1/U2 request occurs
during some situations. The patch is used to avoid it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bridge/br_mdb.c
br_mdb.c conflict was a function call being removed to fix a bug in
'net' but whose signature was changed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Added the USB IDs 0x413c:0x81b1 for the "Dell Wireless 5809e Gobi(TM) 4G
LTE Mobile Broadband Card", a Dell-branded Sierra Wireless EM7305 LTE
card in M.2 form factor, used eg. in Dell's Latitude E7540 Notebook
series.
Signed-off-by: Pieter Hollants <pieter@hollants.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sierra Wireless MC7305/MC7355 with USB ID 1199:9041 also provide a
second QMI/network interface like the MC73xx with USB ID 1199:68c0 on
USB interface #10 when used in the appropriate USB configuration.
Add the corresponding QMI_FIXED_INTF entry to the qmi_wwan driver.
Please note that the second QMI/network interface is not working for
early MC73xx firmware versions like 01.08.x as the device does not
respond to QMI messages on the second /dev/cdc-wdm port.
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update referenced specs link to reflect actual file version and location.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NCM specs are not actually mandating a specific position in the frame for
the NDP (Network Datagram Pointer). However, some Huawei devices will
ignore our aggregates if it is not placed after the datagrams it points
to. Add support for doing just this, in a per-device configurable way.
While at it, update NCM subdrivers, disabling this functionality in all of
them, except in huawei_cdc_ncm where it is enabled instead.
We aren't making any distinction between different Huawei NCM devices,
based on what the vendor driver does. Standard NCM devices are left
unaffected: if they are compliant, they should be always usable, still
stay on the safe side.
This change has been tested and working with a Huawei E3131 device (which
works regardless of NDP position), a Huawei E3531 (also working both
ways) and an E3372 (which mandates NDP to be after indexed datagrams).
V1->V2:
- corrected wrong NDP acronym definition
- fixed possible NULL pointer dereference
- patch cleanup
V2->V3:
- Properly account for the NDP size when writing new packets to SKB
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device is sold as 'NVIDIA Tegra USB 3.0 Ethernet'.
Chipset is RTL8153 and works with r8152.
Signed-off-by: Zheng Liu <zhliu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_curr_frame_payload field is u32. When we try to calculate a
small negative delta based on it, we end up with a positive integer
close to 2^32 instead. So the tx_bytes pointer increases by about
2^32 for every transmitted frame.
Fix by calculating the delta as a signed long.
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Reported-by: Florian Bruhin <me@the-compiler.org>
Fixes: 7a1e890e21 ("usbnet: Fix tx_bytes statistic running backward in cdc_ncm")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
transfer_buffer_length is of type u32. It's therefore wrong to assign it
to a signed integer. This patch avoids the overflow.
It's worth noting that entry->length here is a long; perhaps it would be
beneficial at somepoint to change this to be unsigned as well, if
nothing else relies on its signedness for error conditions or the like.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device is sold as 'Lenovo OneLink Pro Dock'.
Chipset is RTL8153 and works with r8152.
Signed-off-by: Vasily Titskiy <qehgt0@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac-socfpga.c conflict was a case of a bug fix overlapping
changes in net-next to handle an error pointer differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
"kevent" is an extremely generic name that causes trouble
if debugging for work queues is used. So change it to
something clear.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
drivers/net/usb/sr9800.c
drivers/net/usb/usbnet.c
include/linux/usb/usbnet.h
net/ipv4/tcp_ipv4.c
net/ipv6/tcp_ipv6.c
The TCP conflicts were overlapping changes. In 'net' we added a
READ_ONCE() to the socket cached RX route read, whilst in 'net-next'
Eric Dumazet touched the surrounding code dealing with how mini
sockets are handled.
With USB, it's a case of the same bug fix first going into net-next
and then I cherry picked it back into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
This device is sold as 'Lenovo Tinkpad USB 3.0 Ethernet 4X90E51405'.
Chipset is RTL8153 and works with r8152.
Signed-off-by: Christian Hesse <mail@eworm.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
cdc_ncm disagrees with usbnet about how much framing overhead should
be counted in the tx_bytes statistics, and tries 'fix' this by
decrementing tx_bytes on the transmit path. But statistics must never
be decremented except due to roll-over; this will thoroughly confuse
user-space. Also, tx_bytes is only incremented by usbnet in the
completion path.
Fix this by requiring drivers that set FLAG_MULTI_FRAME to set a
tx_bytes delta along with the tx_packets count.
Fixes: beeecd42c3 ("net: cdc_ncm/cdc_mbim: adding NCM protocol statistics")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Currently the usbnet core does not update the tx_packets statistic for
drivers with FLAG_MULTI_PACKET and there is no hook in the TX
completion path where they could do this.
cdc_ncm and dependent drivers are bumping tx_packets stat on the
transmit path while asix and sr9800 aren't updating it at all.
Add a packet count in struct skb_data so these drivers can fill it
in, initialise it to 1 for other drivers, and add the packet count
to the tx_packets statistic on completion.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/netfilter/nf_tables_core.c
The nf_tables_core.c conflict was resolved using a conflict resolution
from Stephen Rothwell as a guide.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device is powered up, some (older) firmware versions fail to work
properly if we send commands before the boot is complete (everything is OK
when the device is hot-plugged). The firmware indicates its ready status by
putting the link up.
Newer firmwares delay the first command so they don't suffer from this problem.
They also report the link being always up.
Wait for firmware to become ready (link up) before sending any commands and/or
data.
This also allows lowering CMD_TIMEOUT value to a reasonable time.
Tested with 4.1.0.9 (old) and 4.1.0.30 (new) firmware versions.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 11ad714b98 because
it breaks cx82310_eth.
The custom USB_DEVICE_CLASS macro matches
bDeviceClass, bDeviceSubClass and bDeviceProtocol
but the common USB_DEVICE_AND_INTERFACE_INFO matches
bInterfaceClass, bInterfaceSubClass and bInterfaceProtocol instead, which are
not specified.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) If an IPVS tunnel is created with a mixed-family destination
address, it cannot be removed. Fix from Alexey Andriyanov.
2) Fix module refcount underflow in netfilter's nft_compat, from Pablo
Neira Ayuso.
3) Generic statistics infrastructure can reference variables sitting on
a released function stack, therefore use dynamic allocation always.
Fix from Ignacy Gawędzki.
4) skb_copy_bits() return value test is inverted in ip_check_defrag().
5) Fix network namespace exit in openvswitch, we have to release all of
the per-net vports. From Pravin B Shelar.
6) Fix signedness bug in CAIF's cfpkt_iterate(), from Dan Carpenter.
7) Fix rhashtable grow/shrink behavior, only expand during inserts and
shrink during deletes. From Daniel Borkmann.
8) Netdevice names with semicolons should never be allowed, because
they serve as a separator. From Matthew Thode.
9) Use {,__}set_current_state() where appropriate, from Fabian
Frederick.
10) Revert byte queue limits support in r8169 driver, it's causing
regressions we can't figure out.
11) tcp_should_expand_sndbuf() erroneously uses tp->packets_out to
measure packets in flight, properly use tcp_packets_in_flight()
instead. From Neal Cardwell.
12) Fix accidental removal of support for bluetooth in CSR based Intel
wireless cards. From Marcel Holtmann.
13) We accidently added a behavioral change between native and compat
tasks, wrt testing the MSG_CMSG_COMPAT bit. Just ignore it if the
user happened to set it in a native binary as that was always the
behavior we had. From Catalin Marinas.
14) Check genlmsg_unicast() return valud in hwsim netlink tx frame
handling, from Bob Copeland.
15) Fix stale ->radar_required setting in mac80211 that can prevent
starting new scans, from Eliad Peller.
16) Fix memory leak in nl80211 monitor, from Johannes Berg.
17) Fix race in TX index handling in xen-netback, from David Vrabel.
18) Don't enable interrupts in amx-xgbe driver until all software et al.
state is ready for the interrupt handler to run. From Thomas
Lendacky.
19) Add missing netlink_ns_capable() checks to rtnl_newlink(), from Eric
W Biederman.
20) The amount of header space needed in macvtap was not calculated
properly, fix it otherwise we splat past the beginning of the
packet. From Eric Dumazet.
21) Fix bcmgenet TCP TX perf regression, from Jaedon Shin.
22) Don't raw initialize or mod timers, use setup_timer() and
mod_timer() instead. From Vaishali Thakkar.
23) Fix software maintained statistics in bcmgenet and systemport
drivers, from Florian Fainelli.
24) DMA descriptor updates in sh_eth need proper memory barriers, from
Ben Hutchings.
25) Don't do UDP Fragmentation Offload on RAW sockets, from Michal
Kubecek.
26) Openvswitch's non-masked set actions aren't constructed properly
into netlink messages, fix from Joe Stringer.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
openvswitch: Fix serialization of non-masked set actions.
gianfar: Reduce logging noise seen due to phy polling if link is down
ibmveth: Add function to enable live MAC address changes
net: bridge: add compile-time assert for cb struct size
udp: only allow UFO for packets from SOCK_DGRAM sockets
sh_eth: Really fix padding of short frames on TX
Revert "sh_eth: Enable Rx descriptor word 0 shift for r8a7790"
sh_eth: Fix RX recovery on R-Car in case of RX ring underrun
sh_eth: Ensure proper ordering of descriptor active bit write/read
net/mlx4_en: Disbale GRO for incoming loopback/selftest packets
net/mlx4_core: Fix wrong mask and error flow for the update-qp command
net: systemport: fix software maintained statistics
net: bcmgenet: fix software maintained statistics
rxrpc: don't multiply with HZ twice
rxrpc: terminate retrans loop when sending of skb fails
net/hsr: Fix NULL pointer dereference and refcnt bugs when deleting a HSR interface.
net: pasemi: Use setup_timer and mod_timer
net: stmmac: Use setup_timer and mod_timer
net: 8390: axnet_cs: Use setup_timer and mod_timer
net: 8390: pcnet_cs: Use setup_timer and mod_timer
...
Currently the usbnet core does not update the tx_packets statistic for
drivers with FLAG_MULTI_PACKET and there is no hook in the TX
completion path where they could do this.
cdc_ncm and dependent drivers are bumping tx_packets stat on the
transmit path while asix and sr9800 aren't updating it at all.
Add a packet count in struct skb_data so these drivers can fill it
in, initialise it to 1 for other drivers, and add the packet count
to the tx_packets statistic on completion.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just another AX88178-based 10/100/1000 USB-to-Ethernet dongle. This one
shows up in lsusb as: "Sitecom Europe B.V. LN-028 Network USB 2.0 Adapter".
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper functions to access current->state.
Direct assignments are prone to races and therefore buggy.
Thanks to Peter Zijlstra for the exact definition of the problem.
Suggested-By: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always read bInterfaceNumber from the current altsetting, not from the first one
available in the altsetting array. This is coming from code review, not related
to any specific bug.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: David S. Miller <davem@davemloft.net>
The National Instruments USB Host-to-Host Cable is based on the Prolific
PL-25A1 chipset. Add its VID/PID so the plusb driver will recognize it.
Signed-off-by: Ben Shelton <ben.shelton@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support setting the rx coalesce. Then someone could change the rx
agg timeout value through ethtool.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx early size is calculated with the mtu, so it has to be
re-calculated when the mtu is changed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate USB_RX_EARLY_AGG into USB_RX_EARLY_TIMEOUT and USB_RX_EARLY_SIZE.
Replace r8153_set_rx_agg() with r8153_set_rx_early_timeout() and
r8153_set_rx_early_size().
Set the default timeout value according to the USB speed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
There is a capability which let the hw could change the settings
automatically when the power change to ON. However, the USB reset
would reset the settings to the hw default, so the driver has to
restore the relative settings. Otherwise, it would influence the
functions of the hw, and the compatibility for the USB hub and
USB host controller.
The relative settings are as following.
- set the power down scale to 96.
- enable the power saving function of USB 2.0.
- disable the ALDPS of ECM mode.
- set burst mode depending on the burst size.
- enable the flow control of endpoint full.
- set fifo empty boundary to 32448 bytes.
- enable the function of exiting LPM when Rx OK occurs.
- set the connect timer to 1.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb allocation fails once the IP header has been received, the rx state is
being set to WAIT_SYNC. The logic, though, shouldn't directly return, as the
buffer may contain a full packet, and therefore the WAIT_SYNC state needs to be
processed (resetting state to WAIT_IP, clearing rx_buf_size and re-initializing
rx_buf_missing).
So, just let the while loop continue so that in the next iteration the WAIT_SYNC
state cleanly stops the loop. The WAIT_SYNC processing will be done just after
that, only if the end of packet is flagged.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan_get_protocol() has been defined and use it to replace
get_protocol().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep NETIF_F_HW_VLAN_CTAG_RX and NETIF_F_HW_VLAN_CTAG_TX at the
same line.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is unnecessary to accress the hw register if the device is unplugged.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace (tp->speed & LINK_STATUS) with netif_carrier_ok().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set LPM timer to 500us, except for RTL_VER_04 which doesn't link at
USB 3.0.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a error occurs when submitting rx, skip the remaining submissions
and try to submit them again next time.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the static attribute groups and the driver data via
tty_port_register_device_attr() instead of manual device_create_file()
and device_remove_file() calls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
The commone register macors (e.g. RSR) is too commont to drivers, it may
be conflict with the architectures (e.g. xtensa, sh).
The related warnings (with allmodconfig under xtensa):
CC [M] drivers/net/usb/sr9700.o
In file included from drivers/net/usb/sr9700.c:24:0:
drivers/net/usb/sr9700.h:65:0: warning: "RSR" redefined
#define RSR 0x06
^
In file included from ./arch/xtensa/include/asm/bitops.h:22:0,
from include/linux/bitops.h:36,
from include/linux/kernel.h:10,
from include/linux/list.h:8,
from include/linux/module.h:9,
from drivers/net/usb/sr9700.c:13:
./arch/xtensa/include/asm/processor.h:190:0: note: this is the location of the previous definition
#define RSR(v,sr) __asm__ __volatile__ ("rsr %0,"__stringify(sr) : "=a"(v));
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using only the usb interface number for the rfkill name, we might
have a name conflicts in case two similar hso devices are connected.
In this patch, the name of the hso rfkill interface embed the value
of a counter that is incremented each time a new rfkill interface is
added.
Suggested-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
For hso serial devices, two cancel_work_sync were missing in the
disconnect method.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The serial_table is used to map the minor number of the usb serial device
to its associated context. The table is updated in the probe method and
in hso_serial_ref_free() which is called either from the tty cleanup
method or from the usb disconnect method.
This patch ensures that the serial_table is updated in the disconnect
method and no more from the cleanup method to avoid the following
potential race condition.
- hso_disconnect() is called for usb interface "x". Because the serial
port was open and because the cleanup method of the tty_port hasn't
been called yet, hso_serial_ref_free() is not run.
- hso_probe() is called and fails for a new hso serial usb interface
"y". The function hso_free_interface() is called and iterates
over the element of serial_table to find the device associated to
the usb interface context.
If the usb interface context of usb interface "y" has been created
at the same place as for usb interface "x", then the cleanup
functions are called for usb interfaces "x" and "y" and
hso_serial_ref_free() is called for both interfaces.
- release_tty() is called for serial port linked to usb interface "x"
and possibly crash because the tty_port structure contained in the
hso_device structure has been freed.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function hso_serial_common_free() is called either by the cleanup
method of the tty or by the usb disconnect method.
In the former case, the usb_disconnect() has been already called
and the sysfs group associated to the device has been removed.
By calling tty_unregister directly from the usb_disconnect() method,
we avoid a warning due to the removal of the sysfs group of the usb
device.
Example of warning:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 778 at fs/sysfs/group.c:225 sysfs_remove_group+0x50/0x94()
sysfs group c0645a88 not found for kobject 'ttyHS5'
Modules linked in:
CPU: 0 PID: 778 Comm: kworker/0:3 Tainted: G W 3.18.0+ #105
Workqueue: events release_one_tty
[<c000dfe4>] (unwind_backtrace) from [<c000c014>] (show_stack+0x14/0x1c)
[<c000c014>] (show_stack) from [<c0016bac>] (warn_slowpath_common+0x5c/0x7c)
[<c0016bac>] (warn_slowpath_common) from [<c0016c60>] (warn_slowpath_fmt+0x30/0x40)
[<c0016c60>] (warn_slowpath_fmt) from [<c00ddd14>] (sysfs_remove_group+0x50/0x94)
[<c00ddd14>] (sysfs_remove_group) from [<c0221e44>] (device_del+0x30/0x190)
[<c0221e44>] (device_del) from [<c0221fb0>] (device_unregister+0xc/0x18)
[<c0221fb0>] (device_unregister) from [<c0221fec>] (device_destroy+0x30/0x3c)
[<c0221fec>] (device_destroy) from [<c01fe1dc>] (tty_unregister_device+0x2c/0x5c)
[<c01fe1dc>] (tty_unregister_device) from [<c029a428>] (hso_serial_common_free+0x2c/0x88)
[<c029a428>] (hso_serial_common_free) from [<c029a4c0>] (hso_serial_ref_free+0x3c/0xb8)
[<c029a4c0>] (hso_serial_ref_free) from [<c01ff430>] (release_one_tty+0x30/0x84)
[<c01ff430>] (release_one_tty) from [<c00271d4>] (process_one_work+0x21c/0x3c8)
[<c00271d4>] (process_one_work) from [<c0027758>] (worker_thread+0x3d8/0x560)
[<c0027758>] (worker_thread) from [<c002be4c>] (kthread+0xc0/0xcc)
[<c002be4c>] (kthread) from [<c0009630>] (ret_from_fork+0x14/0x24)
---[ end trace cb88537fdc8fa208 ]---
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for a dedicated reset work in the hso driver since
there is already a reset work foreseen in usb_interface that does
the same.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
In other functions of the driver, variables of type "struct hso_serial"
are denoted by "serial" and variables of type "struct hso_device" are
denoted by "hso_dev". This patch makes the hso_free_interface()
consistent with these notations.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the rfkill interface was created, a buffer containing the name
of the rfkill node was allocated. This buffer was never freed when the
device disappears.
To fix the problem, we put the name given to rfkill_alloc() in
the hso_net structure.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the disconnect path, tx_buffer should freed like tx_data to avoid
a memory leak when the device disconnects.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device disappear, the function hso_disconnect() is called to
perform cleanup. In the cleanup function, hso_free_interface() calls
tty_port_tty_hangup() in view of scheduling a work to hang up the tty if
needed. If the port was not open then hso_serial_ref_free() is called
directly to cleanup everything. Otherwise, hso_serial_ref_free() is called
when the last fd associated to the port is closed.
For each open port, tty_release() will call the close method,
hso_serial_close(), which drops the last kref and call
hso_serial_ref_free() which unregisters, destroys the tty port
and finally frees the structure in which the tty_port structure
is included. Later, in tty_release(), more precisely when release_tty()
is called, the tty_port previously freed is accessed to cancel
the tty buf workqueue and it leads to a crash.
In view of avoiding this crash, we add a cleanup method that is called
at the end of the hangup process and we drop the last kref in this
function when all the ports have been closed, when tty_port is no
more needed and when it is safe to free the structure containing the
tty_port structure.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
No timer related function is used in this driver.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Chou