Core driver addtionally checks LMP feature bit "Erroneous Data Reporting"
instead of quirk HCI_QUIRK_BROKEN_ERR_DATA_REPORTING to decide if HCI
commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken, so
remove this unnecessary quirk for fake CSR controllers.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
BT core driver should addtionally check LMP feature bit
"Erroneous Data Reporting" instead of quirk
HCI_QUIRK_BROKEN_ERR_DATA_REPORTING set by BT device driver to decide if
HCI commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken.
BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 2, Part C | page 587
This feature indicates whether the device is able to support the
Packet_Status_Flag and the HCI commands HCI_Write_Default_-
Erroneous_Data_Reporting and HCI_Read_Default_Erroneous_-
Data_Reporting.
the quirk was introduced by 'commit cde1a8a992 ("Bluetooth: btusb: Fix
and detect most of the Chinese Bluetooth controllers")' to mark HCI
commands HCI_Read|Write_Default_Erroneous_Data_Reporting broken by BT
device driver, but the reason why these two HCI commands are broken is
that feature "Erroneous Data Reporting" is not enabled by firmware, this
scenario is illustrated by below log of QCA controllers with USB I/F:
@ RAW Open: hcitool (privileged) version 2.22
< HCI Command: Read Local Supported Commands (0x04|0x0002) plen 0
> HCI Event: Command Complete (0x0e) plen 68
Read Local Supported Commands (0x04|0x0002) ncmd 1
Status: Success (0x00)
Commands: 288 entries
......
Read Default Erroneous Data Reporting (Octet 18 - Bit 2)
Write Default Erroneous Data Reporting (Octet 18 - Bit 3)
......
< HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0
> HCI Event: Command Complete (0x0e) plen 4
Read Default Erroneous Data Reporting (0x03|0x005a) ncmd 1
Status: Unknown HCI Command (0x01)
< HCI Command: Read Local Supported Features (0x04|0x0003) plen 0
> HCI Event: Command Complete (0x0e) plen 12
Read Local Supported Features (0x04|0x0003) ncmd 1
Status: Success (0x00)
Features: 0xff 0xfe 0x0f 0xfe 0xd8 0x3f 0x5b 0x87
3 slot packets
......
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Tested-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Event HCI_Truncated_Page_Complete should belong to central
and HCI_Peripheral_Page_Response_Timeout should belong to
peripheral, but hci_set_event_mask_page_2_sync() take these
two events for wrong roles, so correct it by this change.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This sets HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN for MTK controllers
since SCO appear to not work when using HCI_OP_ENHANCED_SETUP_SYNC_CONN.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215576
Signed-off-by: Yuri D'Elia <wavexx@thregr.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add device specific data for max baudrate in autobaud mode. This allows the
host to use a baudrate higher than "init speed" when loading FW in autobaud
mode.
The device specific max baudrate in autobaud mode for CYW55572 is set to
921600 bps. Devices without device specific max baudrate in autobaud mode
will use init speed as before. If no device specific init speed has been
specified, it will default to the bcm_proto default 115200 bps.
The increased baud rate improves FW load time. The exact load time will
depend on the specific system and FW being used. As a rough indication,
the FW load time dropped from ~9s @ 115.2kbps to ~1.7s @ 921.6kbps in one
test.
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Always prevent trying to set device baudrate before calling setup() when
using autobaud mode.
This was previously happening for devices which had device specific data
with member no_early_set_baudrate set to 0.
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
CYW55572 is a Wi-Fi + Bluetooth combo device from Infineon.
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add conditional constraint to make property "reset-gpios" available only
for compatible devices acually having the reset pin.
Make property "brcm,requires-autobaud-mode" depend on property
"shutdown-gpios" as the shutdown pin is required to enter autobaud mode.
I looked at all compatible devices and compiled the matrix below before
formulating the conditional constraint. This was a pure paper exercise and
no verification testing has been performed.
d
e
v h
i o
c s
s e t
h - -
u w w v
t r a a v d
d e k k b d
o s e e a i
w e u u t o
n t p p - -
- - - - s s
g g g g u u
p p p p t p p
i i i i x l p p
o o o o c p l l
s s s s o o y y
---------------------------------------
brcm,bcm20702a1 X X X X X X X X
brcm,bcm4329-bt X X X X X X X X
brcm,bcm4330-bt X X X X X X X X
brcm,bcm4334-bt X - X X X X X X
brcm,bcm43438-bt X - X X X X X X
brcm,bcm4345c5 X - X X X X X X
brcm,bcm43540-bt X - X X X X X X
brcm,bcm4335a0 X - X X X X X X
brcm,bcm4349-bt X - X X X X X X
infineon,cyw55572-bt X - X X X X X X
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
CYW55572 is a Wi-Fi + Bluetooth combo device from Infineon.
Extend the binding with its DT compatible.
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The bt_skb_sendmsg() function can't return NULL so there is no need to
check for that. Several of these checks were removed previously but
this one was missed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Bluetooth HCI devices indicate if they are able to wakeup in the wakeup
callback since 'commit 4539ca67fe ("Bluetooth: Rename driver
.prevent_wake to .wakeup")'. This patch adds a default wakeup callback
for Bluetooth HCI UAR devices. It assumes Bluetooth HCI UART devices are
wakeable for backward compatibility. For those who need a customized
behavior, one can override it before calling hci_uart_register_device().
Fixes: 4539ca67fe ("Bluetooth: Rename driver .prevent_wake to .wakeup")
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
These devices are likely going to be reprogrammed when disconnected so
this avoid a whole bunch of commands attempt to remove and the add back
to the list.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Zhengping Jiang <jiangzp@google.com>
When programming a new entry into the resolving list it shall default
to network mode since the params may contain the mode programmed when
the device was last added to the resolving list.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209745
Fixes: 853b70b506 ("Bluetooth: hci_sync: Set Privacy Mode when updating the resolving list")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Zhengping Jiang <jiangzp@google.com>
Annotate hci_rx_work() with kcov_remote_start() and kcov_remote_stop()
calls, so remote KCOV coverage is collected while processing the rx_q
queue which is the main incoming Bluetooth packet queue.
Coverage is associated with the thread which created the packet skb.
The collected extra coverage helps kernel fuzzing efforts in finding
vulnerabilities.
This change only has effect if the kernel is compiled with CONFIG_KCOV,
otherwise kcov_ functions don't do anything.
Signed-off-by: Tamas Koczka <poprdi@google.com>
Tested-by: Aleksandr Nogikh <nogikh@google.com>
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
After resuming, remove setting scanning_paused to false, because it is
checked and set to false in hci_resume_scan_sync. Also move setting
the value to false before updating passive scan, because the value is
used when resuming passive scan.
Fixes: 3b42055388 (Bluetooth: hci_sync: Fix attempting to suspend with
unfiltered passive scan)
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Commit ce64b3e949 ("Bluetooth: mt7921s: Support wake on bluetooth")
adds the wake on bluethooth via a dedicated GPIO.
Extend the wake-on-bluetooth to use the SDIO DAT1 pin (in-band wakeup),
when supported by the SDIO host driver.
Co-developed-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Set the connection data before calling get_conn_info_sync, so it can be
verified the connection is still connected, before refreshing cached
values.
Fixes: 47db6b4299 ("Bluetooth: hci_sync: Convert MGMT_OP_GET_CONN_INFO")
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The scan response and advertising data needs to be tracked on a per
instance (adv_info) since when these instaces are removed so are their
data, to fix that new flags are introduced which is used to mark when
the data changes and then checked to confirm when the data needs to be
synced with the controller.
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Both dev_name and short_name are not guaranteed to be NULL terminated so
this instead use strnlen and then attempt to determine if the resulting
string needs to be truncated or not.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216018
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Similar to the handling of l2cap_ecred_connect in commit d3715b2333
("Bluetooth: use memset avoid memory leaks"), we thought a patch
might be needed here as well.
Use memset to initialize structs to prevent memory leaks
in l2cap_le_connect
Signed-off-by: Xiaohui Zhang <xiaohuizhang@ruc.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BCM4349B1, aka CYW/BCM89359, is a WiFi+BT chip and its Bluetooth
portion can be controlled over serial.
Two subversions are added for the chip, because ROM firmware reports
002.002.013 (at least for the chips I have here), while depending on
patchram firmware revision, either 002.002.013 or 002.002.014 is
reported.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BCM4349B1, aka CYW/BCM89359, is a WiFi+BT chip and its Bluetooth
portion can be controlled over serial.
Extend the binding with its DT compatible.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When HCI_USERCHANNEL is used, unregister the suspend notifier when
binding and register when releasing. The userchannel socket should be
left alone after open is completed.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When a userchannel socket is released, we should check whether the hdev
is already unregistered before sending out an IndexAdded.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As platform_driver_register() could fail, it should be better
to deal with the return value in order to maintain the code
consisitency.
Fixes: 1ab1f239bf ("Bluetooth: hci_intel: Add support for platform driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If a hardware error occurs and the connections are flushed without a
disconnection_complete event being signaled, the temporary linkkeys are
not flushed.
This change ensures that any outstanding flushable linkkeys are flushed
when the connection are flushed from the hash table.
Additionally, this also makes use of test_and_clear_bit to avoid
multiple attempts to delete the link key that's already been flushed.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use the presence of a DT property, "brcm,requires-autobaud-mode", to enable
startup in autobaud mode. If the property is present, the device is started
in autobaud mode by asserting RTS (BT_UART_CTS_N) prior to powering on the
device.
Also prevent the use of unsupported commands for devices started in
autobaud mode. Only a limited subset of HCI commands are supported in
autobaud mode.
Some devices (e.g. CYW5557x) require autobaud mode to enable FW loading.
Autobaud mode can also be required on some boards where the controller
device is using a non-standard baud rate in normal mode when first powered
on.
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add property, "brcm,requires-autobaud-mode", to enable autobaud mode
selection.
Some devices (e.g. CYW5557x) require autobaud mode to enable FW loading.
Autobaud mode can also be required on some boards where the controller
device is using a non-standard baud rate when first powered on.
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This fixes the return value of qca_wakeup(), since
.wakeup work inversely with original .prevent_wake.
Fixes: 4539ca67fe (Bluetooth: Rename driver .prevent_wake to .wakeup)
Signed-off-by: Sai Teja Aluvala <quic_saluvala@quicinc.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Previous releases - regressions:
- tcp/udp: make early_demux back namespacified.
- dsa: fix issues with vlan_filtering_is_global
Previous releases - always broken:
- ip: fix data-races around ipv4_net_table (round 2, 3 & 4)
- amt: fix validation and synchronization bugs
- can: fix detection of mcp251863
- eth: iavf: fix handling of dummy receive descriptors
- eth: lan966x: fix issues with MAC table
- eth: stmmac: dwmac-mediatek: fix clock issue
Misc:
- dsa: update documentation
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEEg1AjqC77wbdLX2LbKSR5jcyPE6QFAmLZFP0SHHBhYmVuaUBy
ZWRoYXQuY29tAAoJECkkeY3MjxOkwwoP/iE8gwllEfIPKaFRK4/Gxsj4IuAlyfi9
SqEqMS4n6DonK1Npj8RattTSfnKgf4MxN2m9ERdahPCIqggJqdgdEW2mBGjyLXPC
xmOXOUgAr8dZytgMBSVrN6+W/jhXTIy4tFbScEvUa+5OvGobI33rKJvsutABaIQc
8g9hXehim6oY+KFz0wIquS7OcPDWWmj6b5HqCCSXTLwvzTRMaOyOeWmdLBZuvUhh
K0TREiflVUMm9myJcKCvrsi5aRTTvzT95vYaF2jJ5dnlm24Wsv5pLtVWli31NP7I
bYS4LzQb0WcGY6bJSgrzhwAeQZ2gfLBXi8t1f/Gyg3AmWkR8vucDy9Bb7BG/iAnb
73pXLD0znefKMjuhfISsEQ2jsrGx+AfweH2RX+nkR1unrYXODZbT6JEcBsM2d9Me
A+rsOoxyszctOUa2MNMMQ7sxDYhoDNUylrdmN9X++uIEzGxZo5ollwBOI9gHuWle
gm/kj5J8JsSiHD6q1q/xDJPmObsSizMhuvcx3JTJMTadpEjTXwHx1X8EAKEZf+oM
XW1s04LtRUlelyulPbn0k8QgpRYob9DfuwjIaLb5SuAHyxzquDaDJFsYvXR/8j81
y+DUSXH2daFWWJ7YCIAGXMzeyhwHT8xrhy1zdP5ND0zH+YtiWC+tJzv/B/lUJKob
xb9w9CNjNeQ8
=0Dwe
-----END PGP SIGNATURE-----
Merge tag 'net-5.19-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from can.
Still no major regressions, most of the changes are still due to data
races fixes, plus the usual bunch of drivers fixes.
Previous releases - regressions:
- tcp/udp: make early_demux back namespacified.
- dsa: fix issues with vlan_filtering_is_global
Previous releases - always broken:
- ip: fix data-races around ipv4_net_table (round 2, 3 & 4)
- amt: fix validation and synchronization bugs
- can: fix detection of mcp251863
- eth: iavf: fix handling of dummy receive descriptors
- eth: lan966x: fix issues with MAC table
- eth: stmmac: dwmac-mediatek: fix clock issue
Misc:
- dsa: update documentation"
* tag 'net-5.19-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (107 commits)
mlxsw: spectrum_router: Fix IPv4 nexthop gateway indication
net/sched: cls_api: Fix flow action initialization
tcp: Fix data-races around sysctl_tcp_max_reordering.
tcp: Fix a data-race around sysctl_tcp_abort_on_overflow.
tcp: Fix a data-race around sysctl_tcp_rfc1337.
tcp: Fix a data-race around sysctl_tcp_stdurg.
tcp: Fix a data-race around sysctl_tcp_retrans_collapse.
tcp: Fix data-races around sysctl_tcp_slow_start_after_idle.
tcp: Fix a data-race around sysctl_tcp_thin_linear_timeouts.
tcp: Fix data-races around sysctl_tcp_recovery.
tcp: Fix a data-race around sysctl_tcp_early_retrans.
tcp: Fix data-races around sysctl knobs related to SYN option.
udp: Fix a data-race around sysctl_udp_l3mdev_accept.
ip: Fix data-races around sysctl_ip_prot_sock.
ipv4: Fix data-races around sysctl_fib_multipath_hash_fields.
ipv4: Fix data-races around sysctl_fib_multipath_hash_policy.
ipv4: Fix a data-race around sysctl_fib_multipath_use_neigh.
can: rcar_canfd: Add missing of_node_put() in rcar_canfd_probe()
can: mcp251xfd: fix detection of mcp251863
Documentation: fix udp_wmem_min in ip-sysctl.rst
...
Jann reported a race between munmap() and unmap_mapping_range(), where
unmap_mapping_range() will no-op once unmap_vmas() has unlinked the
VMA; however munmap() will not yet have invalidated the TLBs.
Therefore unmap_mapping_range() will complete while there are still
(stale) TLB entries for the specified range.
Mitigate this by force flushing TLBs for VM_PFNMAP ranges.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that architectures are no longer allowed to override
tlb_{start,end}_vma() re-arrange code so that there is only one
implementation for each of these functions.
This much simplifies trying to figure out what they actually do.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previous patch removed the tlb_flush_end() implementation which
used tlb_flush_range(). This means:
- csky did double invalidates, a range invalidate per vma and a full
invalidate at the end
- csky actually has range invalidates and as such the generic
tlb_flush implementation is more efficient for it.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Will Deacon <will@kernel.org>
Tested-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Scattered across the archs are 3 basic forms of tlb_{start,end}_vma().
Provide two new MMU_GATHER_knobs to enumerate them and remove the per
arch tlb_{start,end}_vma() implementations.
- MMU_GATHER_NO_FLUSH_CACHE indicates the arch has flush_cache_range()
but does *NOT* want to call it for each VMA.
- MMU_GATHER_MERGE_VMAS indicates the arch wants to merge the
invalidate across multiple VMAs if possible.
With these it is possible to capture the three forms:
1) empty stubs;
select MMU_GATHER_NO_FLUSH_CACHE and MMU_GATHER_MERGE_VMAS
2) start: flush_cache_range(), end: empty;
select MMU_GATHER_MERGE_VMAS
3) start: flush_cache_range(), end: flush_tlb_range();
default
Obviously, if the architecture does not have flush_cache_range() then
it also doesn't need to select MMU_GATHER_NO_FLUSH_CACHE.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Will Deacon <will@kernel.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the command 'lx-symbols' in gdb exits with the error`Function
"do_init_module" not defined in "kernel/module.c"`. This occurs because
the file kernel/module.c was moved to kernel/module/main.c.
Fix this breakage by changing the path to "kernel/module/main.c" in
LoadModuleBreakpoint.
Signed-off-by: Khalid Masum <khalid.masum.92@gmail.com>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Fixes: cfc1d27789 ("module: Move all into module/")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sedat Dilek noticed that I had an extraneous semicolon at the end of a
line in the previous patch.
It's harmless, but unintentional, and while compilers just treat it as
an extra empty statement, for all I know some other tooling might warn
about it. So clean it up before other people notice too ;)
Fixes: 353f7988dd ("watchqueue: make sure to serialize 'wqueue->defunct' properly")
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
DisplayLink ethernet devices require NTB buffers larger then 32kb
in order to run with highest performance.
This patch is changing upper limit of the rx and tx buffers.
Those buffers are initialized with CDC_NCM_NTB_DEF_SIZE_RX and
CDC_NCM_NTB_DEF_SIZE_TX which is 16kb so by default no device is
affected by increased limit.
Rx and tx buffer is increased under two conditions:
- Device need to advertise that it supports higher buffer size in
dwNtbMaxInMaxSize and dwNtbMaxOutMaxSize.
- cdc_ncm/rx_max and cdc_ncm/tx_max driver parameters must be adjusted
with udev rule or ethtool.
Summary of testing and performance results:
Tests were performed on following devices:
- DisplayLink DL-3xxx family device
- DisplayLink DL-6xxx family device
- ASUS USB-C2500 2.5G USB3 ethernet adapter
- Plugable USB3 1G USB3 ethernet adapter
- EDIMAX EU-4307 USB-C ethernet adapter
- Dell DBQBCBC064 USB-C ethernet adapter
Performance measurements were done with:
- iperf3 between two linux boxes
- http://openspeedtest.com/ instance running on local test machine
Insights from tests results:
- All except one from third party usb adapters were not affected by
increased buffer size to their advertised dwNtbOutMaxSize and
dwNtbInMaxSize.
Devices were generally reaching 912-940Mbps both download and upload.
Only EDIMAX adapter experienced decreased download size from
929Mbps to 827Mbps with iper3, with openspeedtest decrease was from
968Mbps to 886Mbps.
- DisplayLink DL-3xxx family devices experienced performance increase
with iperf3 download from 300Mbps to 870Mbps and
upload from 782Mbps to 844Mbps.
With openspeedtest download increased from 556Mbps to 873Mbps
and upload from 727Mbps to 973Mbps
- DiplayLink DL-6xxx family devices are not affected by
increased buffer size.
Signed-off-by: Łukasz Spintzyk <lukasz.spintzyk@synaptics.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220720060518.541-2-lukasz.spintzyk@synaptics.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This improves performance and stability of
DL-3xxx/DL-5xxx/DL-6xxx device series.
Specifically prevents device from temporary network dropouts when
playing video from the web and network traffic going through is high.
Signed-off-by: Dominik Czerwik <dominik.czerwik@synaptics.com>
Signed-off-by: Łukasz Spintzyk <lukasz.spintzyk@synaptics.com>
Link: https://lore.kernel.org/r/20220720060518.541-1-lukasz.spintzyk@synaptics.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Alex Elder says:
====================
net: ipa: move configuration data files
This series moves the "ipa_data-vX.Y.c" files into a subdirectory.
The first patch adds a Makefile variable containing the list of
supported IPA versions, and uses it to simplify the way these files
are specified.
====================
Link: https://lore.kernel.org/r/20220719150827.295248-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Zijun Hu