Remove the tty_vhangup() from the pty code and just release the
redirect. The tty_vhangup() results in data loss and data out of order
issues.
If you write to a pty master an immediately close the pty master, the
receiver might get a chunk of data dropped, but then receive some later
data. That's obviously something rather unexpected for a user. It
certainly confused my test program.
It turns out that tty_vhangup() on the slave pty gets called from
pty_close(), and that causes the data on the slave side to be flushed,
but due to races more data can be copied into the slave side's buffer
after that. Consider the following sequence:
thread1 thread2 thread3
------- ------- -------
| |-write data into buffer,
| | n_tty buffer is filled
| | along with other buffers
| |-pty_close(master)
| |--tty_vhangup(slave)
| |---tty_ldisc_hangup()
| |----n_tty_flush_buffer()
| |-----reset_buffer_flags()
|-n_tty_read() |
|--up_read(&tty->termios_rwsem);
| |------down_read(&tty->termios_rwsem)
| |------clear n_tty buffer contents
| |------up_read(&tty->termios_rwsem)
|--tty_buffer_flush_work() |
|--schedules work calling |
| flush_to_ldisc() |
| |-flush_to_ldisc()
| |--receive_buf()
| |---tty_port_default_receive_buf()
| |----tty_ldisc_receive_buf()
| |-----n_tty_receive_buf2()
| |------n_tty_receive_buf_common()
| |-------down_read(&tty->termios_rwsem)
| |-------__receive_buf()
| | copies data into n_tty buffer
| |-------up_read(&tty->termios_rwsem)
|--down_read(&tty->termios_rwsem)
|--copy buffer data to user
>From this sequence, you can see that thread2 writes to the buffer then
only clears the part of the buffer in n_tty. The n_tty receive buffer
code then copies more data into the n_tty buffer.
But part of the vhangup, releasing the redirect, is still required to
avoid issues with consoles running on pty slaves. So do that.
As far as I can tell, that is all that should be required.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Link: https://lore.kernel.org/r/20201124004902.1398477-3-minyard@acm.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will be required by the pty code when it removes tty_vhangup() on
master close.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Link: https://lore.kernel.org/r/20201124004902.1398477-2-minyard@acm.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The transmission complete error message provides the status of the
ISR_USART_TC bit. This bit, when set, indicates that the transmission
has not been completed.
The bit status indication is not a very understandable information.
The error message sent on console should indicate that the transmission is
not complete, instead of providing USART_TC bit status.
Update the error message and add a comment for better understanding.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210106162203.28854-9-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean probe and remove port deinit by moving clk_disable_unprepare in a
new dedicated deinit_port function.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Link: https://lore.kernel.org/r/20210106162203.28854-8-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comment for conflicting RTS/CTS config refers to "st, hw-flow-ctrl",
but this property is deprecated since the generic RTS/CTS property has
been introduced by the patch 'serial: stm32: Use generic DT binding for
announcing RTS/CTS lines'.
Update the comment to refer to both generic and deprecated RTS/CTS
properties.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210106162203.28854-7-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds the prefix "_usart" in the name of stm32 usart functions in order to
ease the usage of kernel trace and tools, such as f-trace.
Allows to trace "stm32_usart_*" functions with f-trace. Without this patch,
all the driver functions needs to be added manually in f-trace filter.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20210106162203.28854-4-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes checkpatch --strict warnings and checks:
- checkpatch --strict "Unnecessary parentheses"
- checkpatch --strict "Blank lines aren't necessary before a close brace
- checkpatch --strict "Alignment should match open parenthesis"
- checkpatch --strict "Please don't use multiple blank lines"
- checkpatch --strict "Comparison to NULL could be written ..."
- visual check code ordering warning
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210106162203.28854-3-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA initialization error handling is not properly implemented in the
driver.
Fix DMA initialization error handling by:
- moving TX DMA descriptor request error handling in a new dedicated
fallback_err label
- adding error handling to TX DMA descriptor submission
- adding error handling to RX DMA descriptor submission
This patch depends on '24832ca3ee85 ("tty: serial: stm32-usart: Remove set
but unused 'cookie' variables")' which unfortunately doesn't include a
"Fixes" tag.
Fixes: 3489187204 ("serial: stm32: adding dma support")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210106162203.28854-2-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The main purpose of tty_port::low_latency was removed in commit
a9c3f68f3c (tty: Fix low_latency BUG) back in 2014. It was left in
place for drivers as an optional tune knob. But only one driver has been
using it until the previous commit. So remove this misconcept
completely, given there are no users.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210105120239.28031-11-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the only in-kernel user of tty_port::low_latency. Switch this
last one to test uport->flags directly as tty_port::low_latency is going
away in the next patch.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210105120239.28031-10-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop support for these ioctls:
* PIO_FONT, PIO_FONTX
* GIO_FONT, GIO_FONTX
* PIO_FONTRESET
As was demonstrated by commit 90bfdeef83 (tty: make FONTX ioctl use
the tty pointer they were actually passed), these ioctls are not used
from userspace, as:
1) they used to be broken (set up font on current console, not the open
one) and racy (before the commit above)
2) KDFONTOP ioctl is used for years instead
Note that PIO_FONTRESET is defunct on most systems as VGA_CONSOLE is set
on them for ages. That turns on BROKEN_GRAPHICS_PROGRAMS which makes
PIO_FONTRESET just return an error.
We are removing KD_FONT_FLAG_OLD here as it was used only by these
removed ioctls. kd.h header exists both in kernel and uapi headers, so
we can remove the kernel one completely. Everyone includeing kd.h will
now automatically get the uapi one.
There are now unused definitions of the ioctl numbers and "struct
consolefontdesc" in kd.h, but as it is a uapi header, I am not touching
these.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210105120239.28031-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The constant 20 makes the font sum computation signed which can lead to
sign extensions and signed wraps. It's not much of a problem as we build
with -fno-strict-overflow. But if we ever decide not to, be ready, so
switch the constant to unsigned.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210105120239.28031-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty->ops->close is always called with a valid tty, so the BUG_ON cannot
trigger.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210105120239.28031-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5ce2087ed0 (Fix default compose table initialization) fixed
unicode table so that the values are not sign extended. The upstream
(kbd package) chose a different approach. They use hexadecimal values.
So use the same, so that the output of loadkeys and our shipped file
correspond more to each other.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210105120239.28031-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
loadkeys (from kbd) generates 'unsigned short' instead of 'u_short'
since 2.0.3. It also marks maps as 'static' for longer than kbd's
history.
So adapt the shipped defkeymap.c to conform more to loadkeys output.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210105120239.28031-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the last extern user of the tasklet (set_leds) is in
keyboard.c, we can make keyboard_tasklet local to this unit too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210105120239.28031-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
set_leds and compute_shiftstate are called from a single place in vt.c.
Let's combine these two into vt_set_leds_compute_shiftstate. This allows
for making keyboard_tasklet local in the next patch.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210105120239.28031-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c685af1108 ("serial: mvebu-uart: fix tx lost characters") fixed tx
lost characters at low baud rates but started causing tx lost characters
when kernel is going to power off or reboot.
TX_EMP tells us when transmit queue is empty therefore all characters were
transmitted. TX_RDY tells us when CPU can send a new character.
Therefore we need to use different check prior transmitting new character
and different check after all characters were sent.
This patch splits polling code into two functions: wait_for_xmitr() which
waits for TX_RDY and wait_for_xmite() which waits for TX_EMP.
When rebooting A3720 platform without this patch on UART is print only:
[ 42.699�
And with this patch on UART is full output:
[ 39.530216] reboot: Restarting system
Fixes: c685af1108 ("serial: mvebu-uart: fix tx lost characters")
Signed-off-by: Pali Rohár <pali@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201223191931.18343-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20201223141438.889-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to use xmon with powerpc 8xx, the serial driver
must provide udbg_putc() and udpb_getc().
Provide them via cpm_put_poll_char() and cpm_get_poll_char().
This requires CONFIG_CONSOLE_POLL.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/e4471bf81089252470efb3eed735d71a5b32adbd.1608716197.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For a given struct tty_struct this yields the corresponding statistics
about sent and received characters (and some more) which is needed to
implement an LED trigger for tty devices.
The new function is then used to simplify tty_tiocgicount().
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20201218104246.591315-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a new function tty_kopen_shared() that yields a struct
tty_struct. The semantic difference to tty_kopen() is that the tty is
expected to be used already. So rename tty_kopen() to
tty_kopen_exclusive() for clearness, adapt the single user and put the
common code in a new static helper function.
tty_kopen_shared is to be used to implement an LED trigger for tty
devices in one of the next patches.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20201218104246.591315-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This series adds:
* New drivers and OpenRISC support for the LiteX platform
* A bug fix to support userspace gdb debugging
* Fixes one compile issue with blk-iocost
-----BEGIN PGP SIGNATURE-----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=zTkl
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://github.com/openrisc/linux
Pull OpenRISC updates from Stafford Horne:
- New drivers and OpenRISC support for the LiteX platform
- A bug fix to support userspace gdb debugging
- Fixes one compile issue with blk-iocost
* tag 'for-linus' of git://github.com/openrisc/linux:
openrisc: add local64.h to fix blk-iocost build
openrisc: fix trap for debugger breakpoint signalling
openrisc: add support for LiteX
drivers/tty/serial: add LiteUART driver
dt-bindings: serial: document LiteUART bindings
drivers/soc/litex: add LiteX SoC Controller driver
dt-bindings: soc: document LiteX SoC Controller bindings
dt-bindings: vendor: add vendor prefix for LiteX
-----BEGIN PGP SIGNATURE-----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=1gUa
-----END PGP SIGNATURE-----
Merge tag 'printk-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Finally allow parallel writes and reads into/from the lockless
ringbuffer. But it is not a complete solution. Readers are still
serialized against each other. And nested writes are still prevented
by printk_safe per-CPU buffers.
- Use ttynull as the ultimate fallback for /dev/console.
- Officially allow disabling console output by using console="" or
console=null
- A few code cleanups
* tag 'printk-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
printk: remove logbuf_lock writer-protection of ringbuffer
printk: inline log_output(),log_store() in vprintk_store()
printk: remove obsolete dead assignment
printk/console: Allow to disable console output by using console="" or console=null
init/console: Use ttynull as a fallback when there is no console
printk: ringbuffer: Reference text_data_ring directly in callees.
Here is the "large" set of tty and serial patches for 5.11-rc1.
Nothing major at all, some cleanups and some driver removals, always a
nice sign:
- build warning cleanups
- vt locking and logic unwinding and cleanups
- tiny serial driver fixes and updates
- removal of the synclink serial driver as it's no longer needed
- removal of dead termiox code
All of this has been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX9iGrw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk6ZwCgurjtlXOdtrjM6kcvYfKZcILS7jQAoK1B1rH9
O6fVeZl8qRDWL4p06y2s
=0Uho
-----END PGP SIGNATURE-----
Merge tag 'tty-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the "large" set of tty and serial patches for 5.11-rc1.
Nothing major at all, some cleanups and some driver removals, always a
nice sign:
- build warning cleanups
- vt locking and logic unwinding and cleanups
- tiny serial driver fixes and updates
- removal of the synclink serial driver as it's no longer needed
- removal of dead termiox code
All of this has been in linux-next for a while with no reported issues"
* tag 'tty-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (89 commits)
serial: 8250_pci: Drop bogus __refdata annotation
tty: serial: meson: enable console as module
serial: 8250_omap: Avoid FIFO corruption caused by MDR1 access
serial: imx: Move imx_uart_probe_dt() content into probe()
serial: imx: Remove unneeded of_device_get_match_data() NULL check
tty: Fix whitespace inconsistencies in vt_io_ioctl
serial_core: Check for port state when tty is in error state
dt-bindings: serial: Update DT binding docs to support SiFive FU740 SoC
tty: use const parameters in port-flag accessors
tty: use assign_bit() in port-flag accessors
earlycon: drop semicolon from earlycon macro
tty: Remove dead termiox code
tty/serial/imx: Enable TXEN bit in imx_poll_init().
tty : serial: jsm: Fixed file by adding spacing
tty: serial: uartlite: Support probe deferral
earlycon: simplify earlycon-table implementation
tty: serial: bcm63xx: lower driver dependencies
serial: mxs-auart: Remove unneeded platform_device_id
serial: 8250-mtk: Fix reference leak in mtk8250_probe
serial: imx: Remove unused .id_table support
...
Since commit d73dfc6a41 ("serial: 8250_pci: remove __devexit
usage") in v3.9, the 8250/16550 PCI serial driver no longer has any code
or data located in initmem, hence there is no need to annotate the
pci_serial_quirks structure with __refdata. Drop the annotation, to
avoid suppressing future section warnings.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201211133907.2970460-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable serial driver to be built as a module. To do so, init the
console support on driver/module load instead of using
console_initcall().
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201211005744.12855-1-khilman@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been observed that once per 300-1300 port openings the first
transmitted byte is being corrupted on AM3352 ("v" written to FIFO appeared
as "e" on the wire). It only happened if single byte has been transmitted
right after port open, which means, DMA is not used for this transfer and
the corruption never happened afterwards.
Therefore I've carefully re-read the MDR1 errata (link below), which says
"when accessing the MDR1 registers that causes a dummy under-run condition
that will freeze the UART in IrDA transmission. In UART mode, this may
corrupt the transferred data". Strictly speaking,
omap_8250_mdr1_errataset() performs a read access and if the value is the
same as should be written, exits without errata-recommended FIFO reset.
A brief check of the serial_omap_mdr1_errataset() from the competing
omap-serial driver showed it has no read access of MDR1. After removing the
read access from omap_8250_mdr1_errataset() the data corruption never
happened any more.
Link: https://www.ti.com/lit/er/sprz360i/sprz360i.pdf
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20201210055257.1053028-1-alexander.sverdlin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver only probes via devicetree, we can move the
content of imx_uart_probe_dt() directly into imx_uart_probe() to
make the code simpler.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201209214712.15247-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 5.10-rc1 i.MX is a devicetree-only platform and the NULL check on
of_device_get_match_data() is no longer needed.
This check was only needed when this driver supported both DT and non-DT
platforms.
Remove the unneeded of_device_get_match_data() NULL check.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201126124643.3371-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the moment opening a serial device node (such as /dev/ttyS3)
succeeds even if there is no actual serial device behind it.
Reading/writing/ioctls fail as expected because the uart port is not
initialized (the type is PORT_UNKNOWN) and the TTY_IO_ERROR error state
bit is set fot the tty.
However setting line discipline does not have these checks
8250_port.c (8250 is the default choice made by univ8250_console_init()).
As the result of PORT_UNKNOWN, uart_port::iobase is NULL which
a platform translates onto some address accessing which produces a crash
like below.
This adds tty_port_initialized() to uart_set_ldisc() to prevent the crash.
Found by syzkaller.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Link: https://lore.kernel.org/r/20201203055834.45838-1-aik@ozlabs.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, locking of ->session is very inconsistent; most places
protect it using the legacy tty mutex, but disassociate_ctty(),
__do_SAK(), tiocspgrp() and tiocgsid() don't.
Two of the writers hold the ctrl_lock (because they already need it for
->pgrp), but __proc_set_tty() doesn't do that yet.
On a PREEMPT=y system, an unprivileged user can theoretically abuse
this broken locking to read 4 bytes of freed memory via TIOCGSID if
tiocgsid() is preempted long enough at the right point. (Other things
might also go wrong, especially if root-only ioctls are involved; I'm
not sure about that.)
Change the locking on ->session such that:
- tty_lock() is held by all writers: By making disassociate_ctty()
hold it. This should be fine because the same lock can already be
taken through the call to tty_vhangup_session().
The tricky part is that we need to shorten the area covered by
siglock to be able to take tty_lock() without ugly retry logic; as
far as I can tell, this should be fine, since nothing in the
signal_struct is touched in the `if (tty)` branch.
- ctrl_lock is held by all writers: By changing __proc_set_tty() to
hold the lock a little longer.
- All readers that aren't holding tty_lock() hold ctrl_lock: By
adding locking to tiocgsid() and __do_SAK(), and expanding the area
covered by ctrl_lock in tiocspgrp().
Cc: stable@kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tiocspgrp() takes two tty_struct pointers: One to the tty that userspace
passed to ioctl() (`tty`) and one to the TTY being changed (`real_tty`).
These pointers are different when ioctl() is called with a master fd.
To properly lock real_tty->pgrp, we must take real_tty->ctrl_lock.
This bug makes it possible for racing ioctl(TIOCSPGRP, ...) calls on
both sides of a PTY pair to corrupt the refcount of `struct pid`,
leading to use-after-free errors.
Fixes: 47f86834bb ("redo locking of tty->pgrp")
CC: stable@kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
set_termiox() and the TCGETX handler bail out with -EINVAL immediately
if ->termiox is NULL, but there are no code paths that can set
->termiox to a non-NULL pointer; and no such code paths seem to have
existed since the termiox mechanism was introduced back in
commit 1d65b4a088 ("tty: Add termiox") in v2.6.28.
Similarly, no driver actually implements .set_termiox; and it looks like
no driver ever has.
Delete this dead code; but leave the definition of struct termiox in the
UAPI headers intact.
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20201203020331.2394754-1-jannh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As described in Documentation, poll_init() is called by kgdb to initialize
hardware which supports both poll_put_char() and poll_get_char().
It's necessary to enable TXEN bit, otherwise, it will cause hardware fault
and kernel panic when calling imx_poll_put_char().
Generally, if use /dev/ttymxc0 as kgdb console as well as system
console, ttymxc0 is initialized early by system console which does enable
TXEN bit.But when use /dev/ttymxc1 as kgbd console, ttymxc1 is only
initialized by imx_poll_init() cannot enable the TXEN bit, which will
cause kernel panic.
Signed-off-by: Mingrui Ren <jiladahe1997@gmail.com>
Link: https://lore.kernel.org/r/20201202072543.151-1-972931182@qq.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Give uartlite a chance to be probed when IRQ controller will be finally
available and return potential -EPROBE_DEFER as-is. The condition "<="
has been changed to "<" to follow the recommendation in the header of
platform_get_irq().
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Link: https://lore.kernel.org/r/20201127101953.23700-1-alexander.sverdlin@nokia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of using the array-of-pointers trick to avoid having gcc mess up
the earlycon array stride, specify type alignment when declaring entries
to prevent gcc from increasing alignment.
This is essentially an alternative (one-line) fix to the problem
addressed by commit dd709e72cb ("earlycon: Use a pointer table to fix
__earlycon_table stride").
gcc can increase the alignment of larger objects with static extent as
an optimisation, but this can be suppressed by using the aligned
attribute when declaring variables.
Note that we have been relying on this behaviour for kernel parameters
for 16 years and it indeed hasn't changed since the introduction of the
aligned attribute in gcc-3.1.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20201123102319.8090-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hardware supported by bcm63xx is also used by BCM4908 SoCs family that
is ARM64. In future more architectures may need it as well. There is
nothing arch specific breaking compilation so just stick to requiring
COMMON_CLK.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20201125090608.28442-1-zajec5@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mxs-auart driver is only used for DT platforms and there is no
need to use the platform_device_id structure.
Get rid the platform_device_id structure and retrieve the data via
of_device_get_match_data(), which simplifies the code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201123190438.5636-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pm_runtime_enable will increase power disable depth.
Thus a pairing decrement is needed on the error handling
path to keep it balanced according to context.
Fixes: e32a83c70c ("serial: 8250-mtk: modify mtk uart power and clock management")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201119141126.168850-1-zhangqilong3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl+69egeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGTSYH/ifRBlaxy5UiHFc0
2zdR7pkjWrYfDTTT3sazIAhdlzzcfnkUqgFxOP45F4ZIqeTzunH3sUY+5UlT9IX7
liUgnLxQ/1R9Gx8kPGQfu+tLCey78xVFydGsqJoW9sPRw2R+apMdGGa/lOrk+OXz
DXIN+dDnGFqwCCNJpK+rxQQhFf++IPpSI8z6Y23moOFhsDZrEziHuVFy2FGyRM6z
prZ/us/tcobE8ptCk1RmOxLoJ1DR6UxpA2vLimTE+JD8siOsSWPbjE0KudnWCnd5
BLqIjrsPJbSxyuzzK3v9dnO5wMv7tMDuMIuYM/MQTXDttNwtsqt/aP6gdnUCym7N
5eHEj5g=
=MuO1
-----END PGP SIGNATURE-----
Merge 5.10-rc5 into tty-next
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
stdin, stdout, and stderr standard I/O stream are created for the init
process. They are not available when there is no console registered
for /dev/console. It might lead to a crash when the init process
tries to use them, see the commit 48021f9813 ("printk: handle
blank console arguments passed in.").
Normally, ttySX and ttyX consoles are used as a fallback when no consoles
are defined via the command line, device tree, or SPCR. But there
will be no console registered when an invalid console name is configured
or when the configured consoles do not exist on the system.
Users even try to avoid the console intentionally, for example,
by using console="" or console=null. It is used on production
systems where the serial port or terminal are not visible to
users. Pushing messages to these consoles would just unnecessary
slowdown the system.
Make sure that stdin, stdout, stderr, and /dev/console are always
available by a fallback to the existing ttynull driver. It has
been implemented for exactly this purpose but it was used only
when explicitly configured.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20201111135450.11214-2-pmladek@suse.com
Since 5.10-rc1 i.MX is a devicetree-only platform and the existing
.id_table support in this driver was only useful for old non-devicetree
platforms.
Get rid of the .id_table since it is no longer used.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201115110341.22761-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Functions must follow directly on from their headers
- Demote non-conforming kernel-doc header
- Ensure notes have unique section names
- Provide missing description for 'reinit'
Fixes the following W=1 kernel build warning(s):
drivers/tty/tty_ldisc.c:158: warning: cannot understand function prototype: 'int tty_ldisc_autoload = IS_BUILTIN(CONFIG_LDISC_AUTOLOAD); '
drivers/tty/tty_ldisc.c:199: warning: Function parameter or member 'ld' not described in 'tty_ldisc_put'
drivers/tty/tty_ldisc.c:260: warning: duplicate section name 'Note'
drivers/tty/tty_ldisc.c:717: warning: Function parameter or member 'reinit' not described in 'tty_ldisc_hangup'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201112105857.2078977-2-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/pmac_zilog.h:365:58: warning: variable ‘garbage’ set but not used [-Wunused-but-set-variable]
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linux-serial@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201112105857.2078977-5-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 5.10-rc1 i.MX is a devicetree-only platform and the existing
platform data support in this driver was only useful for old non-devicetree
platforms.
Get rid of the platform data support since it is no longer used.
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201110214840.16768-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have for some time the assign_bit() API to replace open coded
if (foo)
set_bit(n, bar);
else
clear_bit(n, bar);
Use this API in VT keyboard library code.
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20201109105601.47159-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With commit 439c7183e5 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable"),
below warning is seen with W=1 and CONFIG_SERIAL_8250_DMA is disabled:
drivers/tty/serial/8250/8250_omap.c:1199:42: warning: unused variable 'k3_soc_devices' [-Wunused-const-variable]
Fix this by moving the code using k3_soc_devices array to
omap_serial_fill_features_erratas() that handles other errata flags as
well.
Fixes: 439c7183e5 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201111112653.2710-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
k3_soc_devices array is missing a sentinel entry which may result in out
of bounds access as reported by kernel KASAN.
Fix this by adding a sentinel entry.
Fixes: 439c7183e5 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201111112653.2710-1-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabling the lock dependency validator has revealed
that the way spinlocks are used in the IMX serial
port could result in a deadlock.
Specifically, imx_uart_int() acquires a spinlock
without disabling the interrupts, meaning that another
interrupt could come along and try to acquire the same
spinlock, potentially causing the two to wait for each
other indefinitely.
Use spin_lock_irqsave() instead to disable interrupts
upon acquisition of the spinlock.
Fixes: c974991d26 ("tty:serial:imx: use spin_lock instead of spin_lock_irqsave in isr")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sam Nobs <samuel.nobs@taitradio.com>
Link: https://lore.kernel.org/r/1604955006-9363-1-git-send-email-samuel.nobs@taitradio.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds driver for the FPGA-based LiteUART serial controller
from LiteX SoC builder.
The current implementation supports LiteUART configured
for 32 bit data width and 8 bit CSR bus width.
It does not support IRQ.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Here are a small number of small tty and serial fixes for some reported
problems for the tty core, vt code, and some serial drivers.
They include fixes for:
- a buggy and obsolete vt font ioctl removal
- 8250_mtk serial baudrate runtime warnings
- imx serial earlycon build configuration fix
- txx9 serial driver error path cleanup issues
- tty core fix in release_tty that can be triggered by trying to
bind an invalid serial port name to a speakup console device
Almost all of these have been in linux-next without any problems, the
only one that hasn't, just deletes code :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX6g7nQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymmVACeNXgZpIAUJujtM7hQAEpCDYrFZ08An13TN07Y
wZe5okUITYIXQRZevKyi
=w0og
-----END PGP SIGNATURE-----
Merge tag 'tty-5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a small number of small tty and serial fixes for some
reported problems for the tty core, vt code, and some serial drivers.
They include fixes for:
- a buggy and obsolete vt font ioctl removal
- 8250_mtk serial baudrate runtime warnings
- imx serial earlycon build configuration fix
- txx9 serial driver error path cleanup issues
- tty core fix in release_tty that can be triggered by trying to bind
an invalid serial port name to a speakup console device
Almost all of these have been in linux-next without any problems, the
only one that hasn't, just deletes code :)"
* tag 'tty-5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
vt: Disable KD_FONT_OP_COPY
tty: fix crash in release_tty if tty->port is not set
serial: txx9: add missing platform_driver_unregister() on error in serial_txx9_init
tty: serial: imx: enable earlycon by default if IMX_SERIAL_CONSOLE is enabled
serial: 8250_mtk: Fix uart_get_baud_rate warning
It's buggy:
On Fri, Nov 06, 2020 at 10:30:08PM +0800, Minh Yuan wrote:
> We recently discovered a slab-out-of-bounds read in fbcon in the latest
> kernel ( v5.10-rc2 for now ). The root cause of this vulnerability is that
> "fbcon_do_set_font" did not handle "vc->vc_font.data" and
> "vc->vc_font.height" correctly, and the patch
> <https://lkml.org/lkml/2020/9/27/223> for VT_RESIZEX can't handle this
> issue.
>
> Specifically, we use KD_FONT_OP_SET to set a small font.data for tty6, and
> use KD_FONT_OP_SET again to set a large font.height for tty1. After that,
> we use KD_FONT_OP_COPY to assign tty6's vc_font.data to tty1's vc_font.data
> in "fbcon_do_set_font", while tty1 retains the original larger
> height. Obviously, this will cause an out-of-bounds read, because we can
> access a smaller vc_font.data with a larger vc_font.height.
Further there was only one user ever.
- Android's loadfont, busybox and console-tools only ever use OP_GET
and OP_SET
- fbset documentation only mentions the kernel cmdline font: option,
not anything else.
- systemd used OP_COPY before release 232 published in Nov 2016
Now unfortunately the crucial report seems to have gone down with
gmane, and the commit message doesn't say much. But the pull request
hints at OP_COPY being broken
https://github.com/systemd/systemd/pull/3651
So in other words, this never worked, and the only project which
foolishly every tried to use it, realized that rather quickly too.
Instead of trying to fix security issues here on dead code by adding
missing checks, fix the entire thing by removing the functionality.
Note that systemd code using the OP_COPY function ignored the return
value, so it doesn't matter what we're doing here really - just in
case a lone server somewhere happens to be extremely unlucky and
running an affected old version of systemd. The relevant code from
font_copy_to_all_vcs() in systemd was:
/* copy font from active VT, where the font was uploaded to */
cfo.op = KD_FONT_OP_COPY;
cfo.height = vcs.v_active-1; /* tty1 == index 0 */
(void) ioctl(vcfd, KDFONTOP, &cfo);
Note this just disables the ioctl, garbage collecting the now unused
callbacks is left for -next.
v2: Tetsuo found the old mail, which allowed me to find it on another
archive. Add the link too.
Acked-by: Peilin Ye <yepeilin.cs@gmail.com>
Reported-by: Minh Yuan <yuanmingbuaa@gmail.com>
References: https://lists.freedesktop.org/archives/systemd-devel/2016-June/036935.html
References: https://github.com/systemd/systemd/pull/3651
Cc: Greg KH <greg@kroah.com>
Cc: Peilin Ye <yepeilin.cs@gmail.com>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://lore.kernel.org/r/20201108153806.3140315-1-daniel.vetter@ffwll.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2ae0b31e0f ("tty: don't crash in tty_init_dev when missing
tty_port") didn't fully prevent the crash as the cleanup path in
tty_init_dev() calls release_tty() which dereferences tty->port
without checking it for non-null.
Add tty->port checks to release_tty to avoid the kernel crash.
Fixes: 2ae0b31e0f ("tty: don't crash in tty_init_dev when missing tty_port")
Signed-off-by: Matthias Reichl <hias@horus.com>
Link: https://lore.kernel.org/r/20201105123432.4448-1-hias@horus.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing platform_driver_unregister() before return
from serial_txx9_init in the error handling case when failed
to register serial_txx9_pci_driver with macro ENABLE_SERIAL_TXX9_PCI
defined.
Fixes: ab4382d274 ("tty: move drivers/serial/ to drivers/tty/serial/")
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Link: https://lore.kernel.org/r/20201103084942.109076-1-miaoqinglang@huawei.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 699cc4dfd1 (tty: serial: imx: add imx earlycon driver), the earlycon
part of imx serial is a separate driver and isn't necessarily enabled anymore
when the console is enabled. This causes users to loose the earlycon
functionality when upgrading their kenrel configuration via oldconfig.
Enable earlycon by default when IMX_SERIAL_CONSOLE is enabled.
Fixes: 699cc4dfd1 (tty: serial: imx: add imx earlycon driver)
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20201105204026.1818219-1-l.stach@pengutronix.de
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mediatek 8250 port supports speed higher than uartclk / 16. If the baud
rates in both the new and the old termios setting are higher than
uartclk / 16, the WARN_ON in uart_get_baud_rate() will be triggered.
Passing NULL as the old termios so uart_get_baud_rate() will use
uartclk / 16 - 1 as the new baud rate which will be replaced by the
original baud rate later by tty_termios_encode_baud_rate() in
mtk8250_set_termios().
Fixes: 551e553f0d ("serial: 8250_mtk: Fix high-speed baud rates clamping")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Link: https://lore.kernel.org/r/20201102120749.374458-1-tientzu@chromium.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only usage of msm_uart_pops is to assign its address to the ops
field in the uart_port struct, which is a pointer to const. Make it
const to allow the compiler to put it in read-only memory.
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20201104235134.17793-1-rikard.falkeborn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UARTs on TI SoCs prior to J7200 don't provide independent control over
RX FIFO not empty interrupt (RHR_IT) and RX timeout interrupt.
Starting with J7200 SoC, its possible to disable RHR_IT independent of
RX timeout interrupt using bit 2 of IER2 register. So disable RHR_IT
once RX DMA is started so as to avoid spurious interrupt being raised
when data is in the RX FIFO but is yet to be drained by DMA (a known
errata in older SoCs).
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201029051930.7097-1-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/tty/serial/serial_mctrl_gpio.c:214
mctrl_gpio_init() warn: passing zero to 'ERR_PTR'
gpiod_to_irq() never return 0, so remove the useless test
and make code more clear.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20201031030530.1304-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A note from the vendor:
"The hardware used with synclink.c and synclinkmp.c has not been
manufactured for 15 years and was low volume. The chances of either
driver still being in use is very low. Not even Microgate (me) has
the ability to test either anymore (no hardware). I don’t know the
policy about driver removal, but I think both could be removed
without upsetting anyone."
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201105123357.708813-3-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A note from the vendor:
"The hardware used with synclink.c and synclinkmp.c has not been
manufactured for 15 years and was low volume. The chances of either
driver still being in use is very low. Not even Microgate (me) has
the ability to test either anymore (no hardware). I don’t know the
policy about driver removal, but I think both could be removed
without upsetting anyone."
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201105123357.708813-2-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/synclink.c:7708: warning: Function parameter or member 'txqueue' not described in 'hdlcdev_tx_timeout'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: paulkf@microgate.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-37-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/serial-tegra.c:94: warning: Function parameter or member 'fifo_mode_enable_status' not described in 'tegra_uart_chip_data'
drivers/tty/serial/serial-tegra.c:94: warning: Function parameter or member 'uart_max_port' not described in 'tegra_uart_chip_data'
drivers/tty/serial/serial-tegra.c:94: warning: Function parameter or member 'max_dma_burst_bytes' not described in 'tegra_uart_chip_data'
drivers/tty/serial/serial-tegra.c:94: warning: Function parameter or member 'error_tolerance_low_range' not described in 'tegra_uart_chip_data'
drivers/tty/serial/serial-tegra.c:94: warning: Function parameter or member 'error_tolerance_high_range' not described in 'tegra_uart_chip_data'
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-31-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/tty_ldisc.c:160: warning: Function parameter or member 'tty' not described in 'tty_ldisc_get'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-30-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/stm32-usart.c: In function ‘stm32_transmit_chars_dma’:
drivers/tty/serial/stm32-usart.c:353:15: warning: variable ‘cookie’ set but not used [-Wunused-but-set-variable]
drivers/tty/serial/stm32-usart.c: In function ‘stm32_of_dma_rx_probe’:
drivers/tty/serial/stm32-usart.c:1090:15: warning: variable ‘cookie’ set but not used [-Wunused-but-set-variable]
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Gerald Baeza <gerald.baeza@st.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-29-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/synclinkmp.c:1808: warning: Function parameter or member 'txqueue' not described in 'hdlcdev_tx_timeout'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: paulkf@microgate.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-27-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/synclink_gt.c:633: warning: Function parameter or member 'tty' not described in 'ldisc_receive_buf'
drivers/tty/synclink_gt.c:633: warning: Function parameter or member 'data' not described in 'ldisc_receive_buf'
drivers/tty/synclink_gt.c:633: warning: Function parameter or member 'flags' not described in 'ldisc_receive_buf'
drivers/tty/synclink_gt.c:633: warning: Function parameter or member 'count' not described in 'ldisc_receive_buf'
drivers/tty/synclink_gt.c:1683: warning: Function parameter or member 'txqueue' not described in 'hdlcdev_tx_timeout'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: paulkf@microgate.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-24-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/xilinx_uartps.c:205: warning: Function parameter or member 'cts_override' not described in 'cdns_uart'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-23-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/ifx6x60.c:553: warning: Function parameter or member 'tty' not described in 'ifx_port_activate'
drivers/tty/serial/ifx6x60.c:728: warning: Function parameter or member 't' not described in 'ifx_spi_io'
drivers/tty/serial/ifx6x60.c:728: warning: Excess function parameter 'data' description in 'ifx_spi_io'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Filip Aben <f.aben@option.com>
Cc: Joseph Barrow <d.barow@option.com>
Cc: Jan Dumon <j.dumon@option.com>
Cc: Russ Gorby <russ.gorby@intel.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-22-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/msm_serial.c: In function ‘msm_complete_tx_dma’:
drivers/tty/serial/msm_serial.c:429:18: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Robert Love <rlove@google.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lore.kernel.org/r/20201104193549.4026187-21-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/lpc32xx_hs.c: In function ‘__serial_uart_flush’:
drivers/tty/serial/lpc32xx_hs.c:244:6: warning: variable ‘tmp’ set but not used [-Wunused-but-set-variable]
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Kevin Wells <kevin.wells@nxp.com>
Cc: Roland Stigge <stigge@antcom.de>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://lore.kernel.org/r/20201104193549.4026187-20-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/n_gsm.c:85: warning: Function parameter or member 'ref' not described in 'gsm_mux_net'
drivers/tty/n_gsm.c:85: warning: Function parameter or member 'dlci' not described in 'gsm_mux_net'
drivers/tty/n_gsm.c:664: warning: Function parameter or member 'dlci' not described in 'gsm_data_kick'
drivers/tty/n_gsm.c:1015: warning: Function parameter or member 'clen' not described in 'gsm_process_modem'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-19-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When !ACPI 'sbsa_uart_acpi_match' is not referenced.
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/amba-pl011.c:2792:36: warning: ‘sbsa_uart_acpi_match’ defined but not used [-Wunused-const-variable=]
Cc: Russell King <linux@armlinux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-18-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/pty.c:710: warning: Function parameter or member 'file' not described in 'ptm_unix98_lookup'
drivers/tty/pty.c:726: warning: Function parameter or member 'file' not described in 'pts_unix98_lookup'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: "C. Scott Ananian" <cananian@alumni.princeton.edu>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-17-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/tty_audit.c:91: warning: Function parameter or member 'buf' not described in 'tty_audit_buf_push'
drivers/tty/tty_audit.c:129: warning: Function parameter or member 'sig' not described in 'tty_audit_fork'
drivers/tty/tty_audit.c:137: warning: Function parameter or member 'tty' not described in 'tty_audit_tiocsti'
drivers/tty/tty_audit.c:137: warning: Function parameter or member 'ch' not described in 'tty_audit_tiocsti'
drivers/tty/tty_audit.c:202: warning: Function parameter or member 'tty' not described in 'tty_audit_add_data'
drivers/tty/tty_audit.c:202: warning: Function parameter or member 'data' not described in 'tty_audit_add_data'
drivers/tty/tty_audit.c:202: warning: Function parameter or member 'size' not described in 'tty_audit_add_data'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Miloslav Trmac <mitr@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-16-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/8250/serial_cs.c: In function ‘multi_config’:
drivers/tty/serial/8250/serial_cs.c:562:7: warning: variable ‘err’ set but not used [-Wunused-but-set-variable]
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: "David A. Hinds" <dahinds@users.sourceforge.net>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-15-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Demote non-conformant headers and supply some missing descriptions.
Fixes the following W=1 kernel build warning(s):
drivers/tty/tty_io.c:218: warning: Function parameter or member 'file' not described in 'tty_free_file'
drivers/tty/tty_io.c:566: warning: Function parameter or member 'exit_session' not described in '__tty_hangup'
drivers/tty/tty_io.c:1077: warning: Function parameter or member 'tty' not described in 'tty_send_xchar'
drivers/tty/tty_io.c:1077: warning: Function parameter or member 'ch' not described in 'tty_send_xchar'
drivers/tty/tty_io.c:1155: warning: Function parameter or member 'file' not described in 'tty_driver_lookup_tty'
drivers/tty/tty_io.c:1508: warning: Function parameter or member 'tty' not described in 'release_tty'
drivers/tty/tty_io.c:1508: warning: Function parameter or member 'idx' not described in 'release_tty'
drivers/tty/tty_io.c:2973: warning: Function parameter or member 'driver' not described in 'alloc_tty_struct'
drivers/tty/tty_io.c:2973: warning: Function parameter or member 'idx' not described in 'alloc_tty_struct'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Nick Holloway <alfie@dcs.warwick.ac.uk>
Cc: -- <julian@uhunix.uhcc.hawaii.edu>
Cc: Marko Kohtala <Marko.Kohtala@hut.fi>
Cc: Bill Hawes <whawes@star.net>
Cc: "C. Scott Ananian" <cananian@alumni.princeton.edu>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Andrew Morton <andrewm@uow.edu.eu>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-13-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Corey Minyard