Add support for BD9574MWF which is similar chip with BD9571MWV.
Note that we don't support voltage rails VD{09,18,25,33} by this
driver on BD9574. The VD09 voltage could be read from PMIC but that
is not supported by this commit.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
To simplify this driver, use dev_get_regmap() and
rid of using struct bd9571mwv.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warning:
drivers/regulator/bd9571mwv-regulator.c:220:1: warning:
symbol 'dev_attr_backup_mode' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend the existing support for backup mode to toggle power switches.
With a toggle power switch (or level signal), the following steps must
be followed exactly:
1. Configure PMIC for backup mode, to change the role of the
accessory power switch from a power switch to a wake-up switch,
2. Switch accessory power switch off, to prepare for system suspend,
which is a manual step not controlled by software,
3. Suspend system,
4. Switch accessory power switch on, to resume the system.
Hence the PMIC is configured for backup mode when "on" or "1" is written
to the PMIC's "backup_mode" virtual file in sysfs. Conversely, writing
"off" or "0" reverts the role of the accessory switch to a power
switch.
Unlike with momentary switches, backup mode is not enabled by default,
as enabling it prevents the board from being powered off using the power
switch, which may confuse the user.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the BD9571MWV PMIC driver uses the standard "wake_up" sysfs
file to control enablement of DDR Backup Mode.
However, configuring DDR Backup Mode is not really equivalent to
configuring the PMIC as a wake-up source. To avoid confusion, use a
custom "backup_mode" attribute file in sysfs instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
The BD9571MWV PMIC supports backup mode, which keeps one or more DDR
rails powered while the main SoC is powered down.
Which DDR rails are to be kept powered is board-specific, and controlled
using the optional "rohm,ddr-backup-power" DT property. In the absence
of this property, backup mode is not available.
Backup mode can be enabled or disabled by the user using the standard
"wakeup" virtual file in sysfs, e.g. to enable:
echo enabled > /sys/devices/platform/soc/e60b0000.i2c/i2c-7/7-0030/bd9571mwv-regulator.2.auto/power/wakeup
When the PMIC is configured for backup mode, the role of the accessory
power switch changes from a power switch to a wake-up switch.
Two types of switches (or signals) can be used:
A. With a momentary power switch (or pulse signal), the PMIC is
configured for backup mode in the PMIC driver's suspend callback,
during system suspend.
Backup mode is enabled by default, as there is no further impact
during normal system operation.
B. With a toggle power switch (or level signal), the following steps
must be followed exactly:
1. Configure PMIC for backup mode,
2. Switch accessory power switch off, to prepare for system
suspend, which is a manual step not controlled by software,
3. Suspend system.
This mode is not yet supported by the driver.
As the switch type is board-specific, and cannot be determined
automatically, it is obtained from the presence of one of the
"rohm,rstbmode-*" properties in DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
These functions are only used by this driver, make them static.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add driver for the regulator block in the ROHM BD9571MWV-W MFD PMIC.
This block supports three voltage monitors, VD18, VD25, VD33 for the
1V8, 2V5, 3V3 voltage rails and a single voltage regulator for the
DVFS rail.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Yoshihiro Shimoda