Commit 288dab8a35 ("block: add a separate operation type for secure
erase") split REQ_OP_SECURE_ERASE from REQ_OP_DISCARD without considering
all the places REQ_OP_DISCARD was being used to mean either. Fix those.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 288dab8a35 ("block: add a separate operation type for secure erase")
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit abf545484d changed it from an 'rw' flags type to the
newer ops based interface, but now we're effectively leaking
some bdev internals to the rest of the kernel. Since we only
care about whether it's a read or a write at that level, just
pass in a bool 'is_write' parameter instead.
Then we can also move op_is_write() and friends back under
CONFIG_BLOCK protection.
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The rw_page users were not converted to use bio/req ops. As a result
bdev_write_page is not passing down REQ_OP_WRITE and the IOs will
be sent down as reads.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Fixes: 4e1b2d52a8 ("block, fs, drivers: remove REQ_OP compat defs and related code")
Modified by me to:
1) Drop op_flags passing into ->rw_page(), as we don't use it.
2) Make op_is_write() and friends safe to use for !CONFIG_BLOCK
Signed-off-by: Jens Axboe <axboe@fb.com>
In include/linux/blkdev.h duplicate declarations of the request
struct exist. Cleaned up by removing the second, unneeded
declaration.
Signed-off-by: John Pittman <jpittman@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
1/ Replace pcommit with ADR / directed-flushing:
The pcommit instruction, which has not shipped on any product, is
deprecated. Instead, the requirement is that platforms implement either
ADR, or provide one or more flush addresses per nvdimm. ADR
(Asynchronous DRAM Refresh) flushes data in posted write buffers to the
memory controller on a power-fail event. Flush addresses are defined in
ACPI 6.x as an NVDIMM Firmware Interface Table (NFIT) sub-structure:
"Flush Hint Address Structure". A flush hint is an mmio address that
when written and fenced assures that all previous posted writes
targeting a given dimm have been flushed to media.
2/ On-demand ARS (address range scrub):
Linux uses the results of the ACPI ARS commands to track bad blocks
in pmem devices. When latent errors are detected we re-scrub the media
to refresh the bad block list, userspace can also request a re-scrub at
any time.
3/ Support for the Microsoft DSM (device specific method) command format.
4/ Support for EDK2/OVMF virtual disk device memory ranges.
5/ Various fixes and cleanups across the subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xCBG
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
- Replace pcommit with ADR / directed-flushing.
The pcommit instruction, which has not shipped on any product, is
deprecated. Instead, the requirement is that platforms implement
either ADR, or provide one or more flush addresses per nvdimm.
ADR (Asynchronous DRAM Refresh) flushes data in posted write buffers
to the memory controller on a power-fail event.
Flush addresses are defined in ACPI 6.x as an NVDIMM Firmware
Interface Table (NFIT) sub-structure: "Flush Hint Address Structure".
A flush hint is an mmio address that when written and fenced assures
that all previous posted writes targeting a given dimm have been
flushed to media.
- On-demand ARS (address range scrub).
Linux uses the results of the ACPI ARS commands to track bad blocks
in pmem devices. When latent errors are detected we re-scrub the
media to refresh the bad block list, userspace can also request a
re-scrub at any time.
- Support for the Microsoft DSM (device specific method) command
format.
- Support for EDK2/OVMF virtual disk device memory ranges.
- Various fixes and cleanups across the subsystem.
* tag 'libnvdimm-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (41 commits)
libnvdimm-btt: Delete an unnecessary check before the function call "__nd_device_register"
nfit: do an ARS scrub on hitting a latent media error
nfit: move to nfit/ sub-directory
nfit, libnvdimm: allow an ARS scrub to be triggered on demand
libnvdimm: register nvdimm_bus devices with an nd_bus driver
pmem: clarify a debug print in pmem_clear_poison
x86/insn: remove pcommit
Revert "KVM: x86: add pcommit support"
nfit, tools/testing/nvdimm/: unify shutdown paths
libnvdimm: move ->module to struct nvdimm_bus_descriptor
nfit: cleanup acpi_nfit_init calling convention
nfit: fix _FIT evaluation memory leak + use after free
tools/testing/nvdimm: add manufacturing_{date|location} dimm properties
tools/testing/nvdimm: add virtual ramdisk range
acpi, nfit: treat virtual ramdisk SPA as pmem region
pmem: kill __pmem address space
pmem: kill wmb_pmem()
libnvdimm, pmem: use nvdimm_flush() for namespace I/O writes
fs/dax: remove wmb_pmem()
libnvdimm, pmem: flush posted-write queues on shutdown
...
Pull block driver updates from Jens Axboe:
"This branch also contains core changes. I've come to the conclusion
that from 4.9 and forward, I'll be doing just a single branch. We
often have dependencies between core and drivers, and it's hard to
always split them up appropriately without pulling core into drivers
when that happens.
That said, this contains:
- separate secure erase type for the core block layer, from
Christoph.
- set of discard fixes, from Christoph.
- bio shrinking fixes from Christoph, as a followup up to the
op/flags change in the core branch.
- map and append request fixes from Christoph.
- NVMeF (NVMe over Fabrics) code from Christoph. This is pretty
exciting!
- nvme-loop fixes from Arnd.
- removal of ->driverfs_dev from Dan, after providing a
device_add_disk() helper.
- bcache fixes from Bhaktipriya and Yijing.
- cdrom subchannel read fix from Vchannaiah.
- set of lightnvm updates from Wenwei, Matias, Johannes, and Javier.
- set of drbd updates and fixes from Fabian, Lars, and Philipp.
- mg_disk error path fix from Bart.
- user notification for failed device add for loop, from Minfei.
- NVMe in general:
+ NVMe delay quirk from Guilherme.
+ SR-IOV support and command retry limits from Keith.
+ fix for memory-less NUMA node from Masayoshi.
+ use UINT_MAX for discard sectors, from Minfei.
+ cancel IO fixes from Ming.
+ don't allocate unused major, from Neil.
+ error code fixup from Dan.
+ use constants for PSDT/FUSE from James.
+ variable init fix from Jay.
+ fabrics fixes from Ming, Sagi, and Wei.
+ various fixes"
* 'for-4.8/drivers' of git://git.kernel.dk/linux-block: (115 commits)
nvme/pci: Provide SR-IOV support
nvme: initialize variable before logical OR'ing it
block: unexport various bio mapping helpers
scsi/osd: open code blk_make_request
target: stop using blk_make_request
block: simplify and export blk_rq_append_bio
block: ensure bios return from blk_get_request are properly initialized
virtio_blk: use blk_rq_map_kern
memstick: don't allow REQ_TYPE_BLOCK_PC requests
block: shrink bio size again
block: simplify and cleanup bvec pool handling
block: get rid of bio_rw and READA
block: don't ignore -EOPNOTSUPP blkdev_issue_write_same
block: introduce BLKDEV_DISCARD_ZERO to fix zeroout
NVMe: don't allocate unused nvme_major
nvme: avoid crashes when node 0 is memoryless node.
nvme: Limit command retries
loop: Make user notify for adding loop device failed
nvme-loop: fix nvme-loop Kconfig dependencies
nvmet: fix return value check in nvmet_subsys_alloc()
...
For a front merge, the maximum number of sectors of the
request must be checked against the front merge BIO sector,
not the current sector of the request.
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently, presence of direct_access() in block_device_operations
indicates support of DAX on its block device. Because
block_device_operations is instantiated with 'const', this DAX
capablity may not be enabled conditinally.
In preparation for supporting DAX to device-mapper devices, add
QUEUE_FLAG_DAX to request_queue flags to advertise their DAX
support. This will allow to set the DAX capability based on how
mapped device is composed.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: <linux-s390@vger.kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
I wish the OSD code could simply use blk_rq_map_* helpers like
everyone else, but the complex nature of deciding if we have
DATA IN and/or DATA OUT buffers might make this impossible
(at least for a mere human like me).
But using blk_rq_append_bio at least allows sharing the setup code
between request with or without dat a buffers, and given that this
is the last user of blk_make_request it allows getting rid of that
somewhat awkward interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Boaz Harrosh <ooo@electrozaur.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The target SCSI passthrough backend is much better served with the low-level
blk_rq_append_bio construct then the helpers built on top of it, so export it.
Also use the opportunity to remove the pointless request_queue argument and
make the code flow a little more readable.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently blkdev_issue_zeroout cascades down from discards (if the driver
guarantees that discards zero data), to WRITE SAME and then to a loop
writing zeroes. Unfortunately we ignore run-time EOPNOTSUPP errors in the
block layer blkdev_issue_discard helper to work around DM volumes that
may have mixed discard support underneath.
This patch intoroduces a new BLKDEV_DISCARD_ZERO flag to
blkdev_issue_discard that indicates we are called for zeroing operation.
This allows both to ignore the EOPNOTSUPP hack and actually consolidating
the discard_zeroes_data check into the function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The __pmem address space was meant to annotate codepaths that touch
persistent memory and need to coordinate a call to wmb_pmem(). Now that
wmb_pmem() is gone, there is little need to keep this annotation.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently rq->fifo_time is unsigned long but CFQ stores nanosecond
timestamp in it which would overflow on 32-bit archs. Convert it to u64
to avoid the overflow. Since the rq->fifo_time is unioned with struct
call_single_data(), this does not change the size of struct request in
any way.
We have to slightly fixup block/deadline-iosched.c so that comparison
happens in the right types.
Fixes: 9a7f38c42c
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
Instead of overloading the discard support with the REQ_SECURE flag.
Use the opportunity to rename the queue flag as well, and remove the
dead checks for this flag in the RAID 1 and RAID 10 drivers that don't
claim support for secure erase.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Keep the 32-bit CPU and cmd_type flags together to avoid holes on 64-bit
architectures.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
This adds a REQ_OP_FLUSH operation that is sent to request_fn
based drivers by the block layer's flush code, instead of
sending requests with the request->cmd_flags REQ_FLUSH bit set.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch drops the compat definition of req_op where it matches
the rq_flag_bits definitions, and drops the related old and compat
code that allowed users to set either the op or flags for the operation.
We also then store the operation in the bi_rw/cmd_flags field similar
to how we used to store the bio ioprio where it sat in the upper bits
of the field.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch converts the is_sync helpers to use separate variables
for the operation and flags.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch converts the block layer merging code to use separate variables
for the operation and flags, and to check req_op for the REQ_OP.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This converts the block issue discard helper and users to use
the bio_set_op_attrs accessor and only pass in the operation flags
like REQ_SEQURE.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The following patches separate the operation (WRITE, READ, DISCARD,
etc) from the rq_flag_bits flags. This patch adds definitions for
request/bio operations (REQ_OPs) and adds request/bio accessors to
get/set the op.
In this patch the REQ_OPs match the REQ rq_flag_bits ones
for compat reasons while all the code is converted to use the
op accessors in the set. In the last patches the op will become a
number and the accessors and helpers in this patch will be dropped
or updated.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
- Until now, dax has been disabled if media errors were found on
any device. This enables the use of DAX in the presence of these
errors by making all sector-aligned zeroing go through the driver.
- The driver (already) has the ability to clear errors on writes that
are sent through the block layer using 'DSMs' defined in ACPI 6.1.
Other misc changes:
- When mounting DAX filesystems, check to make sure the partition
is page aligned. This is a requirement for DAX, and previously, we
allowed such unaligned mounts to succeed, but subsequent reads/writes
would fail.
- Misc/cleanup fixes from Jan that remove unused code from DAX related to
zeroing, writeback, and some size checks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXQ4GKAAoJEHr6Yb6juE3/zowP/iclIhgXXXMQJRUHJlePMXC8
15sGZ32JS1ak9g7vrsmNVEDNynfNtiMYdBxtUyRuj6xqgwdZvFk3F55KOCPtaeA1
+yADkgeRkTAcwzmHw9WQVEzBCqyzSisdrwtEfH817qdq9FJdH66x2Kos6i+HeAVr
5Q/e4gs7lKrjf384/QBl+wxNZOndJaQAPd2VRHQqx2A9F33v0ljdwRaUG1r4fjK2
dtmhcZCqdQyuAGXW3piTnZc5ZFc3DPqO4FkEfqkEK3lFOflK0fd8wMsAZRp/Jd0j
GJsgnVSWSqG0Dz476djlG0w8t2p5Jv1g9cKChV+ZZEdFLKWHCOUFqXNj8uI8I4k5
cOEKCHyJ3IwfSHhNQqktEWrQN4T8ZXhWtuc9GuV4UZYuqJqHci6EdR/YsWsJjV+L
lm/qvK4ipDS1pivxOy8KX/iN0z7Io8J9GXpStDx3g8iWjLlh4YYlbJLWeeRepo/z
aPlV/QAKcHiGY6jzLExrZIyCWkzwo6O+0p1Kxerv9/7K/32HWbOodZ+tC8eD+N25
pV69nCGf+u50T2TtIx1+iann4NC1r7zg5yqnT9AgpyZpiwR5joCDzI5sXW+D0rcS
vPtfM84Ccdeq/e6mvfIpZgR0/npQapKnrmUest0J7P2BFPHiFPji1KzZ7M+1aFOo
9R6JdrAj0Sc+FBa+cGzH
=v6Of
-----END PGP SIGNATURE-----
Merge tag 'dax-misc-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull misc DAX updates from Vishal Verma:
"DAX error handling for 4.7
- Until now, dax has been disabled if media errors were found on any
device. This enables the use of DAX in the presence of these
errors by making all sector-aligned zeroing go through the driver.
- The driver (already) has the ability to clear errors on writes that
are sent through the block layer using 'DSMs' defined in ACPI 6.1.
Other misc changes:
- When mounting DAX filesystems, check to make sure the partition is
page aligned. This is a requirement for DAX, and previously, we
allowed such unaligned mounts to succeed, but subsequent
reads/writes would fail.
- Misc/cleanup fixes from Jan that remove unused code from DAX
related to zeroing, writeback, and some size checks"
* tag 'dax-misc-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
dax: fix a comment in dax_zero_page_range and dax_truncate_page
dax: for truncate/hole-punch, do zeroing through the driver if possible
dax: export a low-level __dax_zero_page_range helper
dax: use sb_issue_zerout instead of calling dax_clear_sectors
dax: enable dax in the presence of known media errors (badblocks)
dax: fallback from pmd to pte on error
block: Update blkdev_dax_capable() for consistency
xfs: Add alignment check for DAX mount
ext2: Add alignment check for DAX mount
ext4: Add alignment check for DAX mount
block: Add bdev_dax_supported() for dax mount checks
block: Add vfs_msg() interface
dax: Remove redundant inode size checks
dax: Remove pointless writeback from dax_do_io()
dax: Remove zeroing from dax_io()
dax: Remove dead zeroing code from fault handlers
ext2: Avoid DAX zeroing to corrupt data
ext2: Fix block zeroing in ext2_get_blocks() for DAX
dax: Remove complete_unwritten argument
DAX: move RADIX_DAX_ definitions to dax.c
1/ If a mapping overlaps a bad sector fail the request.
2/ Do not opportunistically report more dax-capable capacity than is
requested when errors present.
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
[vishal: fix a conflict with system RAM collision patches]
[vishal: add a 'size' parameter to ->direct_access]
[vishal: fix a conflict with DAX alignment check patches]
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Pull block driver updates from Jens Axboe:
"On top of the core pull request, this is the drivers pull request for
this merge window. This contains:
- Switch drivers to the new write back cache API, and kill off the
flush flags. From me.
- Kill the discard support for the STEC pci-e flash driver. It's
trivially broken, and apparently unmaintained, so it's safer to
just remove it. From Jeff Moyer.
- A set of lightnvm updates from the usual suspects (Matias/Javier,
and Simon), and fixes from Arnd, Jeff Mahoney, Sagi, and Wenwei
Tao.
- A set of updates for NVMe:
- Turn the controller state management into a proper state
machine. From Christoph.
- Shuffling of code in preparation for NVMe-over-fabrics, also
from Christoph.
- Cleanup of the command prep part from Ming Lin.
- Rewrite of the discard support from Ming Lin.
- Deadlock fix for namespace removal from Ming Lin.
- Use the now exported blk-mq tag helper for IO termination.
From Sagi.
- Various little fixes from Christoph, Guilherme, Keith, Ming
Lin, Wang Sheng-Hui.
- Convert mtip32xx to use the now exported blk-mq tag iter function,
from Keith"
* 'for-4.7/drivers' of git://git.kernel.dk/linux-block: (74 commits)
lightnvm: reserved space calculation incorrect
lightnvm: rename nr_pages to nr_ppas on nvm_rq
lightnvm: add is_cached entry to struct ppa_addr
lightnvm: expose gennvm_mark_blk to targets
lightnvm: remove mgt targets on mgt removal
lightnvm: pass dma address to hardware rather than pointer
lightnvm: do not assume sequential lun alloc.
nvme/lightnvm: Log using the ctrl named device
lightnvm: rename dma helper functions
lightnvm: enable metadata to be sent to device
lightnvm: do not free unused metadata on rrpc
lightnvm: fix out of bound ppa lun id on bb tbl
lightnvm: refactor set_bb_tbl for accepting ppa list
lightnvm: move responsibility for bad blk mgmt to target
lightnvm: make nvm_set_rqd_ppalist() aware of vblks
lightnvm: remove struct factory_blks
lightnvm: refactor device ops->get_bb_tbl()
lightnvm: introduce nvm_for_each_lun_ppa() macro
lightnvm: refactor dev->online_target to global nvm_targets
lightnvm: rename nvm_targets to nvm_tgt_type
...
blkdev_dax_capable() is similar to bdev_dax_supported(), but needs
to remain as a separate interface for checking dax capability of
a raw block device.
Rename and relocate blkdev_dax_capable() to keep them maintained
consistently, and call bdev_direct_access() for the dax capability
check.
There is no change in the behavior.
Link: https://lkml.org/lkml/2016/5/9/950
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Jens Axboe <axboe@fb.com>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: Jan Kara <jack@suse.cz>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Boaz Harrosh <boaz@plexistor.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
DAX imposes additional requirements to a device. Add
bdev_dax_supported() which performs all the precondition checks
necessary for filesystem to mount the device with dax option.
Also add a new check to verify if a partition is aligned by 4KB.
When a partition is unaligned, any dax read/write access fails,
except for metadata update.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Jens Axboe <axboe@fb.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: Jan Kara <jack@suse.cz>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Boaz Harrosh <boaz@plexistor.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
In preparation of moving DAX capability checks to the block layer
from filesystem code, add a VFS message interface that aligns with
filesystem's message format.
For instance, a vfs_msg() message followed by XFS messages in case
of a dax mount error may look like:
VFS (pmem0p1): error: unaligned partition for dax
XFS (pmem0p1): DAX unsupported by block device. Turning off DAX.
XFS (pmem0p1): Mounting V5 Filesystem
:
vfs_msg() is largely based on ext4_msg().
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Jens Axboe <axboe@fb.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: Jan Kara <jack@suse.cz>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Boaz Harrosh <boaz@plexistor.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
This is a version of blkdev_issue_discard which doesn't wait for
the I/O to complete, but instead allows the caller to submit
the final bio and/or chain it to others.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Sagi Grimberg <sagig@grimberg.me>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that we converted everything to the newer block write cache
interface, kill off the queue flush_flags and queueable flush
entries.
Signed-off-by: Jens Axboe <axboe@fb.com>
We don't have any drivers left using it, so kill it off. Update
documentation to use the newer blk_queue_write_cache().
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Add an internal helper and flag for setting whether a queue has
write back caching, or write through (or none). Add a sysfs file
to show this as well, and make it changeable from user space.
This will replace the (awkward) blk_queue_flush() interface that
drivers currently use to inform the block layer of write cache state
and capabilities.
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
We could kmalloc() the payload, so need the offset in page.
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs updates from Al Viro:
- Preparations of parallel lookups (the remaining main obstacle is the
need to move security_d_instantiate(); once that becomes safe, the
rest will be a matter of rather short series local to fs/*.c
- preadv2/pwritev2 series from Christoph
- assorted fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (32 commits)
splice: handle zero nr_pages in splice_to_pipe()
vfs: show_vfsstat: do not ignore errors from show_devname method
dcache.c: new helper: __d_add()
don't bother with __d_instantiate(dentry, NULL)
untangle fsnotify_d_instantiate() a bit
uninline d_add()
replace d_add_unique() with saner primitive
quota: use lookup_one_len_unlocked()
cifs_get_root(): use lookup_one_len_unlocked()
nfs_lookup: don't bother with d_instantiate(dentry, NULL)
kill dentry_unhash()
ceph_fill_trace(): don't bother with d_instantiate(dn, NULL)
autofs4: don't bother with d_instantiate(dentry, NULL) in ->lookup()
configfs: move d_rehash() into configfs_create() for regular files
ceph: don't bother with d_rehash() in splice_dentry()
namei: teach lookup_slow() to skip revalidate
namei: massage lookup_slow() to be usable by lookup_one_len_unlocked()
lookup_one_len_unlocked(): use lookup_dcache()
namei: simplify invalidation logics in lookup_dcache()
namei: change calling conventions for lookup_{fast,slow} and follow_managed()
...
Pull libata updates from Tejun Heo:
- ahci grew runtime power management support so that the controller can
be turned off if no devices are attached.
- sata_via isn't dead yet. It got hotplug support and more refined
workaround for certain WD drives.
- Misc cleanups. There's a merge from for-4.5-fixes to avoid confusing
conflicts in ahci PCI ID table.
* 'for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: ahci_xgene: dereferencing uninitialized pointer in probe
AHCI: Remove obsolete Intel Lewisburg SATA RAID device IDs
ata: sata_rcar: Use ARCH_RENESAS
sata_via: Implement hotplug for VT6421
sata_via: Apply WD workaround only when needed on VT6421
ahci: Add runtime PM support for the host controller
ahci: Add functions to manage runtime PM of AHCI ports
ahci: Convert driver to use modern PM hooks
ahci: Cache host controller version
scsi: Drop runtime PM usage count after host is added
scsi: Set request queue runtime PM status back to active on resume
block: Add blk_set_runtime_active()
ata: ahci_mvebu: add support for Armada 3700 variant
libata: fix unbalanced spin_lock_irqsave/spin_unlock_irq() in ata_scsi_park_show()
libata: support AHCI on OCTEON platform
Now that applications need to explicitly ask for polling we can enable it
by default in blk-mq drivers. Note that this will only have an affect
on driver that supply a poll function, which currently only includes nvme.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Stephen Bates <stephen.bates@pmcs.com>
Tested-by: Stephen Bates <stephen.bates@pmcs.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Driver private request types should not get the artifical cap for the
FS requests. This is important to use the full device capabilities
for internal command or NVMe pass through commands.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Jeff Lien <Jeff.Lien@hgst.com>
Tested-by: Jeff Lien <Jeff.Lien@hgst.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Updated by me to use an explicit check for the one command type that
does support extended checking, instead of relying on the ordering
of the enum command values - as suggested by Keith.
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch applies the two introduced helpers to
figure out the 1st and last bvec, and fixes the
original way after bio splitting.
Cc: stable@vger.kernel.org
Reported-by: Sagi Grimberg <sagig@dev.mellanox.co.il>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
In the following patch, the way for figuring out
the last bvec will be changed with a bit cost introduced,
so return immediately if the queue doesn't have virt
boundary limit. Actually most of devices have not
this limit.
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If block device is left runtime suspended during system suspend, resume
hook of the driver typically corrects runtime PM status of the device back
to "active" after it is resumed. However, this is not enough as queue's
runtime PM status is still "suspended". As long as it is in this state
blk_pm_peek_request() returns NULL and thus prevents new requests to be
processed.
Add new function blk_set_runtime_active() that can be used to force the
queue status back to "active" as needed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Tejun Heo <tj@kernel.org>
When a storage device rejects a WRITE SAME command we will disable write
same functionality for the device and return -EREMOTEIO to the block
layer. -EREMOTEIO will in turn prevent DM from retrying the I/O and/or
failing the path.
Yiwen Jiang discovered a small race where WRITE SAME requests issued
simultaneously would cause -EIO to be returned. This happened because
any requests being prepared after WRITE SAME had been disabled for the
device caused us to return BLKPREP_KILL. The latter caused the block
layer to return -EIO upon completion.
To overcome this we introduce BLKPREP_INVALID which indicates that this
is an invalid request for the device. blk_peek_request() is modified to
return -EREMOTEIO in that case.
Reported-by: Yiwen Jiang <jiangyiwen@huawei.com>
Suggested-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Reviewed-by: Yiwen Jiang <jiangyiwen@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull NVMe updates from Jens Axboe:
"Last branch for this series is the nvme changes. It's in a separate
branch to avoid splitting too much between core and NVMe changes,
since NVMe is still helping drive some blk-mq changes. That said, not
a huge amount of core changes in here. The grunt of the work is the
continued split of the code"
* 'for-4.5/nvme' of git://git.kernel.dk/linux-block: (67 commits)
uapi: update install list after nvme.h rename
NVMe: Export NVMe attributes to sysfs group
NVMe: Shutdown controller only for power-off
NVMe: IO queue deletion re-write
NVMe: Remove queue freezing on resets
NVMe: Use a retryable error code on reset
NVMe: Fix admin queue ring wrap
nvme: make SG_IO support optional
nvme: fixes for NVME_IOCTL_IO_CMD on the char device
nvme: synchronize access to ctrl->namespaces
nvme: Move nvme_freeze/unfreeze_queues to nvme core
PCI/AER: include header file
NVMe: Export namespace attributes to sysfs
NVMe: Add pci error handlers
block: remove REQ_NO_TIMEOUT flag
nvme: merge iod and cmd_info
nvme: meta_sg doesn't have to be an array
nvme: properly free resources for cancelled command
nvme: simplify completion handling
nvme: special case AEN requests
...
Pull core block updates from Jens Axboe:
"We don't have a lot of core changes this time around, it's mostly in
drivers, which will come in a subsequent pull.
The cores changes include:
- blk-mq
- Prep patch from Christoph, changing blk_mq_alloc_request() to
take flags instead of just using gfp_t for sleep/nosleep.
- Doc patch from me, clarifying the difference between legacy
and blk-mq for timer usage.
- Fixes from Raghavendra for memory-less numa nodes, and a reuse
of CPU masks.
- Cleanup from Geliang Tang, using offset_in_page() instead of open
coding it.
- From Ilya, rename request_queue slab to it reflects what it holds,
and a fix for proper use of bdgrab/put.
- A real fix for the split across stripe boundaries from Keith. We
yanked a broken version of this from 4.4-rc final, this one works.
- From Mike Krinkin, emit a trace message when we split.
- From Wei Tang, two small cleanups, not explicitly clearing memory
that is already cleared"
* 'for-4.5/core' of git://git.kernel.dk/linux-block:
block: use bd{grab,put}() instead of open-coding
block: split bios to max possible length
block: add call to split trace point
blk-mq: Avoid memoryless numa node encoded in hctx numa_node
blk-mq: Reuse hardware context cpumask for tags
blk-mq: add a flags parameter to blk_mq_alloc_request
Revert "blk-flush: Queue through IO scheduler when flush not required"
block: clarify blk_add_timer() use case for blk-mq
bio: use offset_in_page macro
block: do not initialise statics to 0 or NULL
block: do not initialise globals to 0 or NULL
block: rename request_queue slab cache
For the purpose of communicating the optional presence of a 'struct
page' for the pfn returned from ->direct_access(), introduce a type that
encapsulates a page-frame-number plus flags. These flags contain the
historical "page_link" encoding for a scatterlist entry, but can also
denote "device memory". Where "device memory" is a set of pfns that are
not part of the kernel's linear mapping by default, but are accessed via
the same memory controller as ram.
The motivation for this new type is large capacity persistent memory
that needs struct page entries in the 'memmap' to support 3rd party DMA
(i.e. O_DIRECT I/O with a persistent memory source/target). However,
we also need it in support of maintaining a list of mapped inodes which
need to be unmapped at driver teardown or freeze_bdev() time.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Hansen <dave@sr71.net>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The DAX implementation needs to protect new calls to ->direct_access()
and usage of its return value against the driver for the underlying
block device being disabled. Use blk_queue_enter()/blk_queue_exit() to
hold off blk_cleanup_queue() from proceeding, or otherwise fail new
mapping requests if the request_queue is being torn down.
This also introduces blk_dax_ctl to simplify the interface from fs/dax.c
through dax_map_atomic() to bdev_direct_access().
[willy@linux.intel.com: fix read() of a hole]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Jan Kara <jack@suse.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We currently only have an inline/sync helper to restart a stopped
queue. If drivers need an async version, they have to roll their
own. Add a generic helper instead.
Signed-off-by: Jens Axboe <axboe@fb.com>
Timer context is not very useful for drivers to perform any meaningful abort
action from. So instead of calling the driver from this useless context
defer it to a workqueue as soon as possible.
Note that while a delayed_work item would seem the right thing here I didn't
dare to use it due to the magic in blk_add_timer that pokes deep into timer
internals. But maybe this encourages Tejun to add a sensible API for that to
the workqueue API and we'll all be fine in the end :)
Contains a major update from Keith Bush:
"This patch removes synchronizing the timeout work so that the timer can
start a freeze on its own queue. The timer enters the queue, so timer
context can only start a freeze, but not wait for frozen."
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This is quite a bumper crop of fixes: Three from Arnd correcting various build
issues in some configurations, a lock recursion in qla2xxx. Two potentially
exploitable issues in hpsa and mvsas, a potential null deref in st, A revert
of a bdi registration fix that turned out to cause even more problems, a set
of fixes to allow people who only defined MPT2SAS to still work after the
mpt2/mpt3sas merger and a couple of fixes for issues turned up by the hyper-v
storvsc driver.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJWY8fDAAoJEDeqqVYsXL0MPhwH/Rs05LUU2vnlaZDdDpH5zY56
YQgKh5duF+ZH+Y4NxX5kkLLo05wpE6xD5xp2yzzmnjTA0Uf/yLVHNdb5D6tRZgSo
mZjAX+/wGDb/ErwvwTk/K2mhEvB0iZJJVMyWcG3F9dKgciRCF/p1Gn5EarGmc+vM
w/9xrs1j24Pw7ipHgBj9zU13w+SPMI7LunR0oYL9CJg24jgXG9sAbrwLkox5kHLo
FFBCrZhev1mzFKa1C+Ln3s0iSf0yEQMd4khzPJAUElkw812PZ7I6r4bCP0ZPKDed
JR8zex9jo77RyWZwA7fIathA0/ujv0AeIRXgvzb0/io1Yk577r98vt+S3koQVK8=
=ptgb
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is quite a bumper crop of fixes: three from Arnd correcting
various build issues in some configurations, a lock recursion in
qla2xxx. Two potentially exploitable issues in hpsa and mvsas, a
potential null deref in st, a revert of a bdi registration fix that
turned out to cause even more problems, a set of fixes to allow people
who only defined MPT2SAS to still work after the mpt2/mpt3sas merger
and a couple of fixes for issues turned up by the hyper-v storvsc
driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
mpt3sas: fix Kconfig dependency problem for mpt2sas back compatibility
Revert "scsi: Fix a bdi reregistration race"
mpt3sas: Add dummy Kconfig option for backwards compatibility
Fix a memory leak in scsi_host_dev_release()
block/sd: Fix device-imposed transfer length limits
scsi_debug: fix prevent_allow+verify regressions
MAINTAINERS: Add myself as co-maintainer of the SCSI subsystem.
sd: Make discard granularity match logical block size when LBPRZ=1
scsi: hpsa: select CONFIG_SCSI_SAS_ATTR
scsi: advansys needs ISA dma api for ISA support
scsi_sysfs: protect against double execution of __scsi_remove_device()
st: fix potential null pointer dereference.
scsi: report 'INQUIRY result too short' once per host
advansys: fix big-endian builds
qla2xxx: Fix rwlock recursion
hpsa: logical vs bitwise AND typo
mvsas: don't allow negative timeouts
mpt3sas: Fix use sas_is_tlr_enabled API before enabling MPI2_SCSIIO_CONTROL_TLR_ON flag
Adrian Hunter