This patch converts the Marvell MV643XX ethernet driver to use the
Marvell Orion MDIO driver. As a result, PowerPC and ARM platforms
registering the Marvell MV643XX ethernet driver are also updated to
register a Marvell Orion MDIO driver. This driver voluntarily overlaps
with the Marvell Ethernet shared registers because it will use a subset
of this shared register (shared_base + 0x4 to shared_base + 0x84). The
Ethernet driver is also updated to look up for a PHY device using the
Orion MDIO bus driver.
For ARM and PowerPC we register a single instance of the "mvmdio" driver
in the system like it used to be done with the use of the "shared_smi"
platform_data cookie on ARM.
Note that it is safe to register the mvmdio driver only for the "ge00"
instance of the driver because this "ge00" interface is guaranteed to
always be explicitely registered by consumers of
arch/arm/plat-orion/common.c and other instances (ge01, ge10 and ge11)
were all pointing their shared_smi to ge00. For PowerPC the in-tree
Device Tree Source files mention only one MV643XX ethernet MAC instance
so the MDIO bus driver is registered only when id == 0.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enhances the "mvmdio" to support a SMI error/done interrupt
line which can be used along with a wait queue instead of doing
busy-waiting on the registers. This is a feature which is available in
the mv643xx_eth SMI code and thus reduces again the gap between the two.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames the base register cookie in the mvmdio drive from
"smireg" to "regs" since a subsequent patch is going to use an ioremap()
cookie whose size is larger than a single register of 4 bytes. No
functionnal code change introduced.
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the mvmdio driver not to use device tree
helper functions such as of_mdiobus_register() and of_iomap() so we can
instantiate this driver using a classic platform_device approach. Use
the device manager helper to ioremap() the base register cookie so we
get automatic freeing upon error and removal. This change is harmless
for Device Tree platforms because they will get the driver be registered
the same way as it was before.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the number of calls required to alloc
a zeroed block of memory.
Trivially reduces overall object size.
Other changes around these removals
o Neaten call argument alignment
o Remove an unnecessary OOM message after dma_alloc_coherent failure
o Remove unnecessary gfp_t stack variable
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.
Remove the unnecessary additional error logging.
Around these deletions:
o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This has been tested on a qnap TS-119P II. Note that enabling WOL with
"ethtool -s eth0 wol g" is not enough; you also need to tell the PIC
microcontroller inside the qnap that WOL should be enabled by sending
0xF2 with qcontrol(1) and you have to disable EUP ("Energy-using
Products", a European power-saving thing) by sending 0xF4.
Signed-off-by: Michael Stapelberg <michael@stapelberg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When autoneg has been disabled in the PHY (Marvell 88E1118 here), auto
negotiation between MAC and PHY seem non-functional anymore. The only
way I found to workaround this is to manually configure the MAC with the
settings sent to the PHY earlier.
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial tree from Jiri Kosina:
"Assorted tiny fixes queued in trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (22 commits)
DocBook: update EXPORT_SYMBOL entry to point at export.h
Documentation: update top level 00-INDEX file with new additions
ARM: at91/ide: remove unsused at91-ide Kconfig entry
percpu_counter.h: comment code for better readability
x86, efi: fix comment typo in head_32.S
IB: cxgb3: delay freeing mem untill entirely done with it
net: mvneta: remove unneeded version.h include
time: x86: report_lost_ticks doesn't exist any more
pcmcia: avoid static analysis complaint about use-after-free
fs/jfs: Fix typo in comment : 'how may' -> 'how many'
of: add missing documentation for of_platform_populate()
btrfs: remove unnecessary cur_trans set before goto loop in join_transaction
sound: soc: Fix typo in sound/codecs
treewide: Fix typo in various drivers
btrfs: fix comment typos
Update ibmvscsi module name in Kconfig.
powerpc: fix typo (utilties -> utilities)
of: fix spelling mistake in comment
h8300: Fix home page URL in h8300/README
xtensa: Fix home page URL in Kconfig
...
alloc failures already get standardized OOM
messages and a dump_stack.
Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Fix a few whitespace defects.
Convert a constant 6 to ETH_ALEN.
Use parentheses around sizeof.
Convert vmalloc/memset to vzalloc.
Remove now unused size variables.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The file uses nothing from the version.h header, so there is no reason
to include it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.
Acked-by: Kosta Zertsekel <konszert@marvell.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
perm_addr is initialized correctly in register_netdevice() so to init it in
drivers is no longer needed.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use strlcpy where possible to ensure the string is \0 terminated.
Use always sizeof(string) instead of 32, ETHTOOL_BUSINFO_LEN
and custom defines.
Use snprintf instead of sprint.
Remove unnecessary inits of ->fw_version
Remove unnecessary inits of drvinfo struct.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
NET_ADDR_SET is set in dev_set_mac_address() no need to alter
dev->addr_assign_type value in drivers.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some __dev* markings that snuck in the 3.8-rc1 merge window in
the drivers/net/* directory.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a branch with updates for Marvell's mvebu/kirkwood platforms. They
came in late-ish, and were heavily interdependent such that it didn't
make sense to split them up across the cross-platform topic branches. So
here they are (for the second release in a row) in a branch on their own.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7luC
-----END PGP SIGNATURE-----
Merge tag 'mvebu' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC updates for Marvell mvebu/kirkwood from Olof Johansson:
"This is a branch with updates for Marvell's mvebu/kirkwood platforms.
They came in late-ish, and were heavily interdependent such that it
didn't make sense to split them up across the cross-platform topic
branches. So here they are (for the second release in a row) in a
branch on their own."
* tag 'mvebu' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (88 commits)
arm: l2x0: add aurora related properties to OF binding
arm: mvebu: add Aurora L2 Cache Controller to the DT
arm: mvebu: add L2 cache support
dma: mv_xor: fix error handling path
dma: mv_xor: fix error checking of irq_of_parse_and_map()
dma: mv_xor: use request_irq() instead of devm_request_irq()
dma: mv_xor: clear the window override control registers
arm: mvebu: fix address decoding armada_cfg_base() function
ARM: mvebu: update defconfig with I2C and RTC support
ARM: mvebu: Add SATA support for OpenBlocks AX3-4
ARM: mvebu: Add support for the RTC in OpenBlocks AX3-4
ARM: mvebu: Add support for I2C on OpenBlocks AX3-4
ARM: mvebu: Add support for I2C controllers in Armada 370/XP
arm: mvebu: Add hardware I/O Coherency support
arm: plat-orion: Add coherency attribute when setup mbus target
arm: dma mapping: Export a dma ops function arm_dma_set_mask
arm: mvebu: Add SMP support for Armada XP
arm: mm: Add support for PJ4B cpu and init routines
arm: mvebu: Add IPI support via doorbells
arm: mvebu: Add initial support for power managmement service unit
...
The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers. This patch fixes all of
them back up to be properly aligned.
Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a series of patches that remove the dev* attributes for all
networking drivers, with the exception of wireless drivers, those are in
a different branch.
Use of __devinit, __devexit_p, __devinitdata, __devinitconst, and
__devexit are no longer needed since CONFIG_HOTPLUG is being removed as
an option.
Note, there are some devinit compiler section mismatch warnings due to
this series, but they are fixed up when merged with my driver-next
branch, which fixes the PCI device id warnings, and removes the modpost
detection, as it's no longer needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlC9COEACgkQMUfUDdst+ykOEgCeKZsrtKrbjMFM5jEROqnk33FI
SwEAoMSZWFJ7M1/27FGRkylmmypWXi/p
=HH3A
-----END PGP SIGNATURE-----
Merge tag 'dev_removal' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/net-next
Networking: Remove __dev* markings from the networking drivers
This is a series of patches that remove the dev* attributes for all
networking drivers, with the exception of wireless drivers, those are in
a different branch.
Use of __devinit, __devexit_p, __devinitdata, __devinitconst, and
__devexit are no longer needed since CONFIG_HOTPLUG is being removed as
an option.
Note, there are some devinit compiler section mismatch warnings due to
this series, but they are fixed up when merged with my driver-next
branch, which fixes the PCI device id warnings, and removes the modpost
detection, as it's no longer needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cleanup sequence in sky2_probe() that is called in case of an error is
mixed up in different places:
- pci_disable_device() is not called in each case the device has been enabled
before
- same for pci_disable_msi(): test_msi() may return with an error != EOPNOTSUPP
(due to failure of request_irq()). In that case msi is not disabled
- also failure of register_netdev() does not disable msi
This patch fixes the concerning parts.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
mvneta_deinit() can be called from the ->probe() hook in the error
path, so it shouldn't be marked as __devexit. It fixes the following
section mismatch warning:
WARNING: vmlinux.o(.devinit.text+0x239c): Section mismatch in reference
from the function mvneta_probe() to the function .devexit.text:mvneta_deinit()
The function __devinit mvneta_probe() references
a function __devexit mvneta_deinit().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Now that the Armada 370/XP platform has gained proper integration with
the clock framework, we add clk support in the Marvell Armada 370/XP
Ethernet driver.
Since the existing Device Tree binding that exposes a
'clock-frequency' property has never been exposed in any stable kernel
release, we take the freedom of removing this property to replace it
with the standard 'clocks' clock pointer property.
The Device Tree binding documentation is updated accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
As reported by checkpatch, the multiline comments for net/ and
drivers/net/ have a slightly different format than the one used in the
rest of the kernel, so we adjust our multiline comments accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
As reported by checkpatch, the multiline comments for net/ and
drivers/net/ have a slightly different format than the one used in the
rest of the kernel, so we adjust our multiline comment accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
As suggested by checkpatch, using <linux/delay.h> instead of
<asm/delay.h> is appropriate.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch contains a new network driver for the network unit of the
ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B
processor, a Marvell-developed ARM core that implements the ARMv7
instruction set.
Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery),
the network unit in Armada 370 and Armada XP is highly different. This
is the reason why this new 'mvneta' driver is needed, while the older
ARM Marvell SoCs use the 'mv643xx_eth' driver.
Here is an overview of the most important hardware changes that
require a new, specific, driver for the network unit of Armada 370/XP:
- The new network unit has a completely different design and layout
for the RX and TX descriptors. They are now organized as a simple
array (each RX and TX queue has base address and size of this
array) rather than a linked list as in the old SoCs.
- The new network unit has a different RXQ and TXQ management: this
management is done using special read/write counter registers,
while in the Old SocS, it was done using the Ownership bit in RX
and TX descriptors.
- The new network unit has different interrupt registers
- The new network unit way of cleaning of interrupts is not done by
writing to the cause register, but by updating per-queue counters
- The new network unit has different GMAC registers (link, speed,
duplex configuration) and different WRR registers.
- The new network unit has lots of new units like PnC (Parser and
Classifier), PMT, BM (Memory Buffer Management), xPON, and more.
The driver proposed in the current patch only handles the basic
features. Additional hardware features will progressively be supported
as needed.
This code has originally been written by Rami Rosen
<rosenr@marvell.com>, and then reviewed and cleaned up by Thomas
Petazzoni <thomas.petazzoni@free-electrons.com>.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: David S. Miller <davem@davemloft.net>
This patch adds a separate driver for the MDIO interface of the
Marvell Ethernet controllers. There are two reasons to have a separate
driver rather than including it inside the MAC driver itself:
*) The MDIO interface is shared by all Ethernet ports, so a driver
must guarantee non-concurrent accesses to this MDIO interface. The
most logical way is to have a separate driver that handles this
single MDIO interface, used by all Ethernet ports.
*) The MDIO interface is the same between the existing mv643xx_eth
driver and the new mvneta driver. Even though it is for now only
used by the mvneta driver, it will in the future be used by the
mv643xx_eth driver as well.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some driver uses tasklet_disable in device remove/close process,
tasklet_disable will inc tasklet->count and return. If the tasklet
is not handled yet because some softirq pressure, the tasklet will
placed on the tasklet_vec, never have a chance to excute. This might
lead to ksoftirqd heavy loaded, wakeup with pending_softirq, but
tasklet is disabled. tasklet_kill should be used in this case.
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_<level> calls take less code than dev_printk(KERN_<LEVEL>
and reducing object size is good.
Coalesce formats for easier grep.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current GRO can hold packets in gro_list for almost unlimited
time, in case napi->poll() handler consumes its budget over and over.
In this case, napi_complete()/napi_gro_flush() are not called.
Another problem is that gro_list is flushed in non friendly way :
We scan the list and complete packets in the reverse order.
(youngest packets first, oldest packets last)
This defeats priorities that sender could have cooked.
Since GRO currently only store TCP packets, we dont really notice the
bug because of retransmits, but this behavior can add unexpected
latencies, particularly on mice flows clamped by elephant flows.
This patch makes sure no packet can stay more than 1 ms in queue, and
only in stress situations.
It also complete packets in the right order to minimize latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 88E8001 on an ASUS P5NSLI motherboard is unable to send/receive
packets on a system with >4gb ram unless a 32bit DMA mask is used.
This issue has been around for years and a fix was sent 3.5 years ago, but
there was some debate as to whether it should instead be fixed as a PCI quirk.
http://www.spinics.net/lists/netdev/msg88670.html
However, 18 months later a similar workaround was introduced for another
chipset exhibiting the same problem.
http://www.spinics.net/lists/netdev/msg142287.html
Signed-off-by: Graham Gower <graham.gower@gmail.com>
Signed-off-by: Jan Ceuleers <jan.ceuleers@computer.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function sky2_probe() return 0 for success and negative value
for most of its internal tests failures. There are two exceptions
that are error cases going to err_out*:. For this two cases, the
function abort its success execution path, but returns non negative
value, making it dificult for a caller function to notice the error.
This patch fixes the error cases that do not return negative values.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function skge_probe() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to err_out_led_off:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.
This patch fixes the error case that do not return negative value.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Over time, skb recycling infrastructure got litle interest and
many bugs. Generic rx path skb allocation is now using page
fragments for efficient GRO / TCP coalescing, and recyling
a tx skb for rx path is not worth the pain.
Last identified bug is that fat skbs can be recycled
and it can endup using high order pages after few iterations.
With help from Maxime Bizon, who pointed out that commit
87151b8689 (net: allow pskb_expand_head() to get maximum tailroom)
introduced this regression for recycled skbs.
Instead of fixing this bug, lets remove skb recycling.
Drivers wanting really hot skbs should use build_skb() anyway,
to allocate/populate sk_buff right before netif_receive_skb()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clk patches added code to get and enable clocks in the
respective driver probe functions. If the probe function failed
for some reason after enabling the clock, the clock was not
disabled again in many cases.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lumm <andrew@lunn.ch>
Re-enable interrupts if it is not our interrupt
Signed-off-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Optima EEE chipset.
Signed-off-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
drivers/net/wireless/iwlwifi/pcie/trans.c
The iwlwifi conflict was resolved by keeping the code added
in 'net' that turns off the buggy chip feature.
The MAINTAINERS conflict was merely overlapping changes, one
change updated all the wireless web site URLs and the other
changed some GIT trees to be Johannes's instead of John's.
Signed-off-by: David S. Miller <davem@davemloft.net>
The newer flavors of Yukon II use a different method for receive
checksum offload. This is indicated in the driver by the SKY2_HW_NEW_LE
flag. On these newer chips, the BMU_ENA_RX_CHKSUM should not be set.
The driver would get incorrectly toggle the bit, enabling the old
checksum logic on these chips and cause a BUG_ON() assertion. If
receive checksum was toggled via ethtool.
Reported-by: Kirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 452503ebc (ARM: Orion: Eth: Add clk/clkdev support.) broke
the building of the driver on architectures which don't have clk
support. In particular PPC32 Pegasos which uses this driver.
Add #ifdef around the clk API usage.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding casts of objects to the same type is unnecessary
and confusing for a human reader.
For example, this cast:
int y;
int *p = (int *)&y;
I used the coccinelle script below to find and remove these
unnecessary casts. I manually removed the conversions this
script produces of casts with __force, __iomem and __user.
@@
type T;
T *p;
@@
- (T *)p
+ p
A function in atl1e_main.c was passed a const pointer
when it actually modified elements of the structure.
Change the argument to a non-const pointer.
A function in stmmac needed a __force to avoid a sparse
warning. Added it.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new clock subsystem was merged in linux-3.4 without any users, this
now moves the first three platforms over to it: imx, mxs and spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that require
these changes, in order to avoid interdependencies and conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rwFF
-----END PGP SIGNATURE-----
Merge tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
* 'clk-next' of git://git.linaro.org/people/mturquette/linux:
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
ARM: Orion: SDIO: Add support for clk.
ARM: Orion: NAND: Add support for clk, if there is one.
ARM: Orion: EHCI: Add support for enabling clocks
ARM: Orion: SATA: Add per channel clk/clkdev support.
ARM: Orion: UART: Get the clock rate via clk_get_rate().
ARM: Orion: WDT: Add clk/clkdev support
ARM: Orion: Eth: Add clk/clkdev support.
ARM: Orion: SPI: Add clk/clkdev support.
ARM: Orion: Add clocks using the generic clk infrastructure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The t_clk is moved from the shared part of the ethernet driver into
the per port section. Each port can have its own gated clock, which it
needs to enable/disable, as oppossed to there being one clock shared
by all ports. In practice, only kirkwood supports this at the moment.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug: The VLAN bit of the MAC RX Status Word is unreliable in several older
supported chips. Sometimes the VLAN bit is not set for valid VLAN packets
and also sometimes the VLAN bit is set for non-VLAN packets that came after
a VLAN packet. This results in a receive length error when VLAN hardware
tagging is enabled.
Fix: Variation on original fix proposed by Mirko.
The VLAN information is decoded in the status loop, and can be
applied to the received SKB there. This eliminates the need for the
separate tag field in the interface data structure. The tag has to
be copied and cleared if packet is copied. This version checked out
with vlan and normal traffic.
Note: vlan_tx_tag_present should be renamed vlan_tag_present, but that
is outside scope of this.
Reported-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a small packet is received, the driver copies it to a new skb to allow
reusing the full size Rx buffer. The copy was propogating the checksum offload
but not the receive hash information. The bug is impact was mostly harmless
and therefore not observed until reviewing this area of code.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modified from original patch from Chris.
The sky2 driver has to have 8 byte alignment of receive buffer
on some chip versions. On architectures which don't support efficient
unaligned access this doesn't work very well. The solution is to
just copy all received packets which is what the driver already
does for small packets.
This allows the driver to be used on the Tilera TILEmpower-Gx, since
the tile architecture doesn't currently handle kernel unaligned accesses,
just userspace.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In sky2_test_msi() the temporarily set SW IRQ in B0 register is not reset in case
that request_irq() fails.
With this patch we only set the interrupt mask if request_irq() was successful.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Provide device string properly for USB i2400m wimax devices, also
don't OOPS when providing firmware string. From Phil Sutter.
2) Add support for sh_eth SH7734 chips, from Nobuhiro Iwamatsu.
3) Add another device ID to USB zaurus driver, from Guan Xin.
4) Loop index start in pool vector iterator is wrong causing MAC to not
get configured in bnx2x driver, fix from Dmitry Kravkov.
5) EQL driver assumes HZ=100, fix from Eric Dumazet.
6) Now that skb_add_rx_frag() can specify the truesize increment
separately, do so in f_phonet and cdc_phonet, also from Eric
Dumazet.
7) virtio_net accidently uses net_ratelimit() not only on the kernel
warning but also the statistic bump, fix from Rick Jones.
8) ip_route_input_mc() uses fixed init_net namespace, oops, use
dev_net(dev) instead. Fix from Benjamin LaHaise.
9) dev_forward_skb() needs to clear the incoming interface index of the
SKB so that it looks like a new incoming packet, also from Benjamin
LaHaise.
10) iwlwifi mistakenly initializes a channel entry as 2GHZ instead of
5GHZ, fix from Stanislav Yakovlev.
11) Missing kmalloc() return value checks in orinoco, from Santosh
Nayak.
12) ath9k doesn't check for HT capabilities in the right way, it is
checking ht_supported instead of the ATH9K_HW_CAP_HT flag. Fix from
Sujith Manoharan.
13) Fix x86 BPF JIT emission of 16-bit immediate field of AND
instructions, from Feiran Zhuang.
14) Avoid infinite loop in GARP code when registering sysfs entries.
From David Ward.
15) rose protocol uses memcpy instead of memcmp in a device address
comparison, oops. Fix from Daniel Borkmann.
16) Fix build of lpc_eth due to dev_hw_addr_rancom() interface being
renamed to eth_hw_addr_random(). From Roland Stigge.
17) Make ipv6 RTM_GETROUTE interpret RTA_IIF attribute the same way
that ipv4 does. Fix from Shmulik Ladkani.
18) via-rhine has an inverted bit test, causing suspend/resume
regressions. Fix from Andreas Mohr.
19) RIONET assumes 4K page size, fix from Akinobu Mita.
20) Initialization of imask register in sky2 is buggy, because bits are
"or'd" into an uninitialized local variable. Fix from Lino
Sanfilippo.
21) Fix FCOE checksum offload handling, from Yi Zou.
22) Fix VLAN processing regression in e1000, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
sky2: dont overwrite settings for PHY Quick link
tg3: Fix 5717 serdes powerdown problem
net: usb: cdc_eem: fix mtu
net: sh_eth: fix endian check for architecture independent
usb/rtl8150 : Remove duplicated definitions
rionet: fix page allocation order of rionet_active
via-rhine: fix wait-bit inversion.
ipv6: Fix RTM_GETROUTE's interpretation of RTA_IIF to be consistent with ipv4
net: lpc_eth: Fix rename of dev_hw_addr_random
net/netfilter/nfnetlink_acct.c: use linux/atomic.h
rose_dev: fix memcpy-bug in rose_set_mac_address
Fix non TBI PHY access; a bad merge undid bug fix in a previous commit.
net/garp: avoid infinite loop if attribute already exists
x86 bpf_jit: fix a bug in emitting the 16-bit immediate operand of AND
bonding: emit event when bonding changes MAC
mac80211: fix oper channel timestamp updation
ath9k: Use HW HT capabilites properly
MAINTAINERS: adding maintainer for ipw2x00
net: orinoco: add error handling for failed kmalloc().
net/wireless: ipw2x00: fix a typo in wiphy struct initilization
...
This patch corrects a bug in function sky2_open() of the Marvell Yukon 2 driver
in which the settings for PHY quick link are overwritten.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Acked-by: Stephen Hemminger <shemminger@vyattta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
Some BIOS's don't setup power management correctly (what else is
new) and don't allow use of PCI Express power control. Add a special
exception module parameter to allow working around this issue.
Based on slightly different patch by Knut Petersen.
Reported-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch removes unused stats member in pxa168 network driver.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unify return value of .ndo_set_mac_address if the given address
isn't valid. Return -EADDRNOTAVAIL as eth_mac_addr() already does
if is_valid_ether_addr() fails.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_hw_addr_random() instead of calling random_ether_addr()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.
v2: adapt to renamed eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by several people...
The code in rx_clean was panic'ing so revert
commit d0249e4443.
Will redo DMA mapping checks as new patches for a later release.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaced deprecating dev_alloc_skb with netdev_alloc_skb in drivers/net/ethernet
- Removed extra skb->dev = dev after netdev_alloc_skb
Signed-off-by: Pradeep A Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures use dump_stack so emitting an additional
out-of-memory message is an unnecessary duplication.
Remove the allocation failure messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also changes the cleanup logic slightly to aggregate
completed notifications for multiple packets.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These statistics helped me a lot while searching who is losing
packets in my setup.
I added these stats to MIB group since they are very similar,
but just in other registers.
I have tested this patch on 88F6281 SoC.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver should check for mapping errors.
Machines with limited DMA maps may return an error when a PCI map is
requested (not an issue on standard x86).
Also use upper/lower 32 bits macros for clarity.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skge device would assert carrier (link up) as soon as network device open
was called, rather than waiting until PHY has detected link.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=N2B4
-----END PGP SIGNATURE-----
Merge tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
New feature development
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
* tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mfd/db8500-prcmu: remove support for early silicon revisions
ARM: ux500: fix the smp_twd clock calculation
ARM: ux500: remove support for early silicon revisions
ARM: ux500: update register files
ARM: ux500: register DB5500 PMU dynamically
ARM: ux500: update ASIC detection for U5500
ARM: ux500: support DB8520
ARM: picoxcell: implement watchdog restart
ARM: OMAP3+: hwmod data: Add the default clockactivity for I2C
ARM: OMAP3: hwmod data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3
ARM: OMAP: hwmod data: Add support for AM35xx UART4/ttyO3
ARM: Orion: Remove address map info from all platform data structures
ARM: Orion: Get address map from plat-orion instead of via platform_data
ARM: Orion: mbus_dram_info consolidation
ARM: Orion: Consolidate the address map setup
ARM: Kirkwood: Add configuration for MPP12 as GPIO
ARM: Kirkwood: Recognize A1 revision of 6282 chip
ARM: ux500: update the MOP500 GPIO assignments
...
drivers/net/ethernet/marvell/skge.c:4046: warning: ‘skge_suspend’ defined but not used
drivers/net/ethernet/marvell/skge.c:4071: warning: ‘skge_resume’ defined but not used
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restore skge hardware registers for multicast filtering to their
appropriate values after system resume and after hardware restarts
that are done when changing certain settings.
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use an getter function in plat-orion/addr-map.c to get the address map
structure, rather than pass it to drivers in the platform_data
structures. When the drivers are built for none orion platforms, a
dummy function is provided instead which returns NULL.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
This adds support for byte queue limits and aggregates statistics
update (suggestion from Eric).
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@drr.davemloft.net>
This patch converts the drivers in drivers/net/ethernet/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Pantelis Antoniou <pantelis.antoniou@gmail.com>
Cc: Vitaly Bordug <vbordug@ru.mvista.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Sebastian Poehn <sebastian.poehn@belden.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix below build error:
CC drivers/net/ethernet/marvell/mv643xx_eth.o
drivers/net/ethernet/marvell/mv643xx_eth.c: In function 'mv643xx_eth_get_drvinfo':
drivers/net/ethernet/marvell/mv643xx_eth.c:1505: error: 'info' undeclared (first use in this function)
drivers/net/ethernet/marvell/mv643xx_eth.c:1505: error: (Each undeclared identifier is reported only once
drivers/net/ethernet/marvell/mv643xx_eth.c:1505: error: for each function it appears in.)
make[4]: *** [drivers/net/ethernet/marvell/mv643xx_eth.o] Error 1
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per discussion with Ben Hutchings and David Miller, go through and
remove assignments of "N/A" to fw_version in various drivers'
.get_drvinfo routines. While there clean-up some use of bare
constants and such.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The forcedeth changes had a conflict with the conversion over
to atomic u64 statistics in net-next.
The libertas cfg.c code had a conflict with the bss reference
counting fix by John Linville in net-next.
Conflicts:
drivers/net/ethernet/nvidia/forcedeth.c
drivers/net/wireless/libertas/cfg.c
If IRQ was never initialized, then calling napi_disable() would hang.
Add more bookkeeping to track whether IRQ was ever initialized.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware has a restriction that the minimum ring size possible
is 128. The number of elements used is controlled by tx_pending and
the overall number of elements in the ring tx_ring_size, therefore it
is okay to limit the number of elements in use to a small value (63)
but still provide a bigger ring.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Save some punctuation by using bool type's property equivalent to
doubled negation operator.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than generating a different RSS key on each boot, just use
a predetermined value that will map same flow to same value on
every device.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default Tx ring size for the sky2 driver is quite large and could
cause excess buffer bloat for many users. The minimum ring size
possible and still allow handling the worst case packet on 64bit platforms
is 38 which gets rounded up to a power of 2. But most packets only require
a couple of ring elements.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code is clearer if the up/down functions are renamed to
open/close like other drivers. Purely syntax change.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A couple of the reset and setup paths have possible PCI posting issues.
When setting registers, a read is necessary to force the writes to complete.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several problems with recent change to how IRQ's are setup.
* synchronize_irq in sky2_shutdown would hang because there
was no IRQ setup.
* when device was set to down, some IRQ bits left enabled so a
hardware error would produce IRQ with no handler
* quick link on Optima chip set was enabled without handler
* suspend/resume would leave IRQ on with no handler if device
was down
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per the mention made by Ben Hutchings that strlcpy is now the preferred
string copy routine for a .get_drvinfo routine, do a bit of floor
sweeping and convert some of the as-yet unconverted ethernet drivers to
it.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to support other Optima types, introduced an accidental
regression that caused 88E8059 to come up in 10Mbit/sec.
The Yukon Optima supports a reverse auto-negotiation feature that
was incorrectly setup, and not needed. The feature could be used to
allow wake-on-lan at higher speeds. But doing it correctly would require
other changes to initialization.
Reported-by: Pavel Mateja <pavel@netsafe.cz>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1745 commits)
dp83640: free packet queues on remove
dp83640: use proper function to free transmit time stamping packets
ipv6: Do not use routes from locally generated RAs
|PATCH net-next] tg3: add tx_dropped counter
be2net: don't create multiple RX/TX rings in multi channel mode
be2net: don't create multiple TXQs in BE2
be2net: refactor VF setup/teardown code into be_vf_setup/clear()
be2net: add vlan/rx-mode/flow-control config to be_setup()
net_sched: cls_flow: use skb_header_pointer()
ipv4: avoid useless call of the function check_peer_pmtu
TCP: remove TCP_DEBUG
net: Fix driver name for mdio-gpio.c
ipv4: tcp: fix TOS value in ACK messages sent from TIME_WAIT
rtnetlink: Add missing manual netlink notification in dev_change_net_namespaces
ipv4: fix ipsec forward performance regression
jme: fix irq storm after suspend/resume
route: fix ICMP redirect validation
net: hold sock reference while processing tx timestamps
tcp: md5: add more const attributes
Add ethtool -g support to virtio_net
...
Fix up conflicts in:
- drivers/net/Kconfig:
The split-up generated a trivial conflict with removal of a
stale reference to Documentation/networking/net-modules.txt.
Remove it from the new location instead.
- fs/sysfs/dir.c:
Fairly nasty conflicts with the sysfs rb-tree usage, conflicting
with Eric Biederman's changes for tagged directories.
To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.
Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sky2 allocates a page per skb fragment. We must account
PAGE_SIZE increments on skb->truesize, not the actual frag length.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per comments from Ben Hutchings on a previous patch, sweep the floors
a little removing unnecessary assignments of zero to fields of struct
ethtool_ringparam in driver code supporting ethtool -g.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I converted some drivers from pci_map_page to skb_frag_dma_map I
neglected to convert PCI_DMA_xDEVICE into DMA_x_DEVICE and
pci_dma_mapping_error into dma_mapping_error.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most boards with SysKonnect/Marvell Ethernet have only a single port.
For the single port case, use the standard Ethernet driver convention
of allocating IRQ when device is brought up rather than at probe time.
This patch also adds some additional read after writes to avoid any
PCI posting problems when setting the IRQ mask.
The error handling of dual port cards is also changed. If second port
can not be brought up, then just fail. No point in continuing, since
the failure is most certainly because of out of memory.
It is worth noting that the dual port skge device has a single irq but two
seperate status rings and therefore has two NAPI objects, one for
each port.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most sky2 hardware only has a single port, although some variations of the
chip support two interfaces. For the single port case, use the standard
Ethernet driver convention of allocating IRQ when device is brought up
rather than at probe time.
Also, change the error handling of dual port cards so that if second
port can not be brought up, then just fail. No point in continuing, since
the failure is most certainly because of out of memory.
The dual port sky2 device has a single irq and a single status ring,
therefore it has a single NAPI object shared by both ports.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on finds for Stephen Rothwell, where current defconfig's
enable a ethernet driver and it is not compiled due to the newly
added NET_VENDOR_* component of Kconfig.
This patch enables all the "new" Kconfig options so that current
defconfig's will continue to compile the expected drivers. In
addition, by enabling all the new Kconfig options does not add
any un-expected options.
CC: Stephen Rothwll <sfc@canb.auug.org.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use IFF_UNICAST_FTL to find out if driver handles unicast address
filtering. In case it does not, promisc mode is entered.
Patch also fixes following drivers:
stmmac, niu: support uc filtering and yet it propagated
ndo_set_multicast_list
bna, benet, pxa168_eth, ks8851, ks8851_mll, ksz884x : has set
ndo_set_rx_mode but do not support uc filtering
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the Marvell Ethernet drivers into drivers/net/ethernet/marvell/
and make the necessary Kconfig and Makefile changes.
CC: Sachin Sanap <ssanap@marvell.com>
CC: Zhangfei Gao <zgao6@marvell.com>
CC: Philip Rakity <prakity@marvell.com>
CC: Mark Brown <markb@marvell.com>
CC: Lennert Buytenhek <buytenh@marvell.com>
CC: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Florian Fainelli