Current pciehp returns successfully on read/write failure with dummy
state values. It should return error instead.
With this patch, pciehp no longer uses hotplug_slot_info data
structure. So this also removes hotplug_slot_info related code. But
note that it still allocates hotplug_slot_info because it is required
by pci hotplug core.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pciehp driver creates 'attention' and 'latch' files even if
the controller doesn't support them. In this case, the contents of
those files are meaningless and unpredictable. Those files should be
created only if the controller has the corresponding capabilities.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove wrong workaround for BAD DLLP error, which confused surprise
down error with DLL errors.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pciehp doesn't handle Data Link Layer State Changed Event
notification. So it needs to be disabled at initialization time,
otherwise other event notifications are not generated.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When probing for ROM BAR size, we should not change bits 1:10 in this
BAR, because these bits are marked as "reserved for future use" in PCI
spec, so changing them might have side effects.
No such issue for I/O or memory, as there is an implementation note in
PCI spec which explicitly allows writing 0xfffffffff there.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch is predicated on Jeremy's patch in include/xen/xen.h. It'll
prevent ACS init unless the platform has both an IOMMU and we're running
as dom0.
Signed-off-by: Allen Kay <allen.m.kay@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Note: dom0 checking in v4 has been separated out into 2/2.
This patch enables P2P upstream forwarding in ACS capable PCIe switches.
It solves two potential problems in virtualization environment where a PCIe
device is assigned to a guest domain using a HW iommu such as VT-d:
1) Unintentional failure caused by guest physical address programmed
into the device's DMA that happens to match the memory address range
of other downstream ports in the same PCIe switch. This causes the PCI
transaction to go to the matching downstream port instead of go to the
root complex to get translated by VT-d as it should be.
2) Malicious guest software intentionally attacks another downstream
PCIe device by programming the DMA address into the assigned device
that matches memory address range of the downstream PCIe port.
We are in process of implementing device filtering software in KVM/XEN
management software to allow device assignment of PCIe devices behind a PCIe
switch only if it has ACS capability and with the P2P upstream forwarding bits
enabled. This patch is intended to work for both KVM and Xen environments.
Signed-off-by: Allen Kay <allen.m.kay@intel.com>
Reviewed-by: Mathew Wilcox <willy@linux.intel.com>
Reviewed-by: Chris Wright <chris@sous-sol.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
As a followup to 71a082efc9, it's conceivable
that some vendors may expose PCI hotplug functionality through both vendor
mechanisms and ACPI. The native mechanism will generally be a superset of
any functionality provided via ACPI, so the acpiphp driver should always
be initialised after any others. Change the link order such that acpiphp
will not be initialised until any other statically linked drivers have had
an opportunity to claim the hardware.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_dfl_cache_line_size is marked as __initdata but referenced by
pci_init() which is __devinit. Make it __devinitdata instead of
__initdata.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For non hotplug PCI devices, the system firmware usually configures
CLS correctly. For pccard devices system firmware can't do it and
Linux PCI layer doesn't do it either. Unfortunately this leads to
poor performance for certain devices (sata_sil). Unless MWI, which
requires separate configuration, is to be used, CLS doesn't affect
correctness, so the configuration should be harmless.
This patch makes pci_set_cacheline_size() always built and export it
and make pccard call it during attach.
Please note that some other PCI hotplug drivers (shpchp and pciehp)
also configure CLS on hotplug.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Greg KH <greg@kroah.com>
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Axel Birndt <towerlexa@gmx.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
sparc64 is now the only user of PCI_CACHE_LINE_BYTES. Drop it and set
pci_dfl_cache_line_size from pcibios_init() instead and drop
PCI_CACHE_LINE_BYTES handling from generic pci code.
Orignally-From: David Miller <davem@davemloft.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Till now, CLS has been determined either by arch code or as
L1_CACHE_BYTES. Only x86 and ia64 set CLS explicitly and x86 doesn't
always get it right. On most configurations, the chance is that
firmware configures the correct value during boot.
This patch makes pci_init() determine CLS by looking at what firmware
has configured. It scans all devices and if all non-zero values
agree, the value is used. If none is configured or there is a
disagreement, pci_dfl_cache_line_size is used. arch can set the dfl
value (via PCI_CACHE_LINE_BYTES or pci_dfl_cache_line_size) or
override the actual one.
ia64, x86 and sparc64 updated to set the default cls instead of the
actual one.
While at it, declare pci_cache_line_size and pci_dfl_cache_line_size
in pci.h and drop private declarations from arch code.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Miller <davem@davemloft.net>
Acked-by: Greg KH <gregkh@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This reverts commit 308cf8e13f. This
patch had trouble with transparent bridges, among other things. A more
readable and correct version should land in 2.6.33.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit d43c36dc6b ("headers: remove
sched.h from interrupt.h") left some build errors in some configurations
due to drivers having depended on getting header files "accidentally".
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[ Combined several one-liners from Ingo into one single patch - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.infradead.org/~dwmw2/iommu-2.6.32:
x86: Move pci_iommu_init to rootfs_initcall()
Run pci_apply_final_quirks() sooner.
Mark pci_apply_final_quirks() __init rather than __devinit
Rename pci_init() to pci_apply_final_quirks(), move it to quirks.c
intel-iommu: Yet another BIOS workaround: Isoch DMAR unit with no TLB space
intel-iommu: Decode (and ignore) RHSA entries
intel-iommu: Make "Unknown DMAR structure" message more informative
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: Prevent AER driver from being loaded on non-root port PCIE devices
PCI: get larger bridge ranges when space is available
PCI: pci.c: fix kernel-doc notation
PCI quirk: TI XIO200a erroneously reports support for fast b2b transfers
PCI PM: Read device power state from register after updating it
PCI: remove pci_assign_resource_fixed()
PCI: PCIe portdrv: remove "-driver" from driver name
Having this as a device_initcall() means that some real device drivers
can actually initialise _before_ the quirks are run, which is wrong.
We want it to run _before_ device_initcall(), but _after_ fs_initcall(),
since some arch-specific PCI initialisation like pcibios_assign_resources()
is done at fs_initcall().
We could use rootfs_initcall() but I actually want to use that for the
IOMMU initialisation, which has to come after the quirks, but still
before the real devices. So use fs_initcall_sync() instead -- since this
is entirely synchronous, it doesn't hurt that it'll escape the
synchronisation.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This function may have done more in the past, but all it does now is
apply the PCI_FIXUP_FINAL quirks. So name it sensibly and put it where
it belongs.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
A bug was seen on boards using a PLX 8518 switch device which advertises
AER on each of it's transparent bridges. The AER driver was loaded for
each bridge and this driver tried to access the AER source ID register
whenever an interrupt occured on the shared PCI INTX lines. The source
ID register does not exist on non root port PCIE device's which
advertise AER and trying to access this register causes a unsupported
request error on the bridge. Thus, when the next interrupt occurs,
another error is found and the non existent source ID register is
accessed again, and so it goes on.
The result is a spammed dmesg with unsupported request PCI express
errors on the bridge device that the AER driver is loaded against.
Reported-by: Malcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Malcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Found one system:
[ 71.120590] pci 0000:40:05.0: scanning behind bridge, config 4f4a40, pass 0
[ 71.138283] PCI: Scanning bus 0000:4a
[ 71.140341] pci 0000:4a:00.0: found [15b3:6278] class 000c06 header type 00
[ 71.157173] pci 0000:4a:00.0: reg 10 64bit mmio: [0x000000-0x0fffff]
[ 71.161697] pci 0000:4a:00.0: reg 18 64bit mmio pref: [0x000000-0x7fffff]
[ 71.179403] pci 0000:4a:00.0: reg 20 64bit mmio pref: [0x000000-0xfffffff]
[ 71.185366] pci 0000:4a:00.0: calling quirk_resource_alignment+0x0/0x1dd
[ 71.200846] pci 0000:4a:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 71.219623] PCI: Fixups for bus 0000:4a
[ 71.222194] pci 0000:40:05.0: bridge 32bit mmio: [0xcf000000-0xcf0fffff]
[ 71.238662] pci 0000:40:05.0: bridge 64bit mmio pref: [0xcd800000-0xcdffffff]
[ 71.255793] PCI: Bus scan for 0000:4a returning with max=4a
Device needs a big pref mmio, but BIOS doesn't allocate mmio to it aside
from a small MMIO range. Later, the kernel will not allocate resources to
that to the device:
[ 99.574030] pci 0000:4a:00.0: BAR 4: can't allocate mem resource [0xd0000000-0xcdffffff]
[ 99.580102] pci 0000:4a:00.0: BAR 2: got res [0xcd800000-0xcdffffff] bus [0xcd800000-0xcdffffff] flags 0x12120c
[ 99.602307] pci 0000:4a:00.0: BAR 2: moved to bus [0xcd800000-0xcdffffff] flags 0x12120c
[ 99.615991] pci 0000:4a:00.0: BAR 0: got res [0xcf000000-0xcf0fffff] bus [0xcf000000-0xcf0fffff] flags 0x120204
[ 99.634499] pci 0000:4a:00.0: BAR 0: moved to bus [0xcf000000-0xcf0fffff] flags 0x120204
[ 99.654318] pci 0000:40:05.0: PCI bridge, secondary bus 0000:4a
[ 99.658766] pci 0000:40:05.0: IO window: disabled
[ 99.675478] pci 0000:40:05.0: MEM window: 0xcf000000-0xcf0fffff
[ 99.681663] pci 0000:40:05.0: PREFETCH window: 0x000000cd800000-0x000000cdffffff
So try to get a big range in the pci bridge if there is no child using
that range. With the patch we get:
[ 99.104525] pci 0000:4a:00.0: BAR 4: got res [0xfc080000000-0xfc08fffffff] bus [0xfc080000000-0xfc08fffffff] flags 0x12120c
[ 99.123624] pci 0000:4a:00.0: BAR 4: moved to bus [0xfc080000000-0xfc08fffffff] flags 0x12120c
[ 99.131977] pci 0000:4a:00.0: BAR 2: got res [0xfc090000000-0xfc0907fffff] bus [0xfc090000000-0xfc0907fffff] flags 0x12120c
[ 99.149788] pci 0000:4a:00.0: BAR 2: moved to bus [0xfc090000000-0xfc0907fffff] flags 0x12120c
[ 99.169248] pci 0000:4a:00.0: BAR 0: got res [0xc0200000-0xc02fffff] bus [0xc0200000-0xc02fffff] flags 0x120204
[ 99.189508] pci 0000:4a:00.0: BAR 0: moved to bus [0xc0200000-0xc02fffff] flags 0x120204
[ 99.206402] pci 0000:40:05.0: PCI bridge, secondary bus 0000:4a
[ 99.210637] pci 0000:40:05.0: IO window: disabled
[ 99.224856] pci 0000:40:05.0: MEM window: 0xc0200000-0xc03fffff
[ 99.230019] pci 0000:40:05.0: PREFETCH window: 0x000fc080000000-0x000fc097ffffff
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This quirk will disable fast back to back transfer on the secondary bus
segment of the TI Bridge.
Signed-off-by: Gabe Black <gabe.black@ni.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
After attempting to change the power state of a PCI device
pci_raw_set_power_state() doesn't check if the value it wrote into
the device's PCI_PM_CTRL register has been stored in there, but
unconditionally modifies the device's current_state field to reflect
the change. This may cause problems to happen if the power state of
the device hasn't been changed in fact, because it will make the PCI
PM core make a wrong assumption.
To prevent such situations from happening modify
pci_raw_set_power_state() so that it reads the device's PCI_PM_CTRL
register after writing into it and uses the value read from the
register to update the device's current_state field. Also make it
print a message saying that the device refused to change its power
state as requested (returning an error code in such cases would cause
suspend regressions to appear on some systems, where device drivers'
suspend routines return error codes if pci_set_power_state() fails).
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Adrian commented out this function in 2baad5f96b, but I don't think
it's even worth cluttering the file with the unused code.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No need to include "-driver" in the driver name.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Tom Long Nguyen <tom.l.nguyen@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Allocate dma-remapping structures using numa locality info. On platforms
having remapping hardware units span different nodes, this enables
optimized dma-remapping transalation structures access by remapping hardware.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Allocate intr-remapping table using numa locality info. On platforms
having remapping hardware units span different nodes, this enables
optimized intr-remapping table entry access by remapping hardware.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for parsing Remapping Hardware Static Affinity (RHSA) structure.
This enables identifying the association between remapping hardware units and
the corresponding proximity domain. This enables to allocate transalation
structures closer to the remapping hardware unit.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Asus decided to ship a BIOS which configures sound DMA to go via the
dedicated IOMMU unit, but assigns precisely zero TLB entries to that
unit. Which causes the whole thing to deadlock, including the DMA
traffic on the _other_ IOMMU units. Nice one.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit 15b8dd53f5 changed info->hardware_id from a static array to
a pointer. If hardware_id is non-NULL, it points to a NULL-terminated
string, so we don't need to terminate it explicitly. However, it may
be NULL; in that case, we *can't* add a NULL terminator.
This causes a NULL pointer dereference oops for devices without _HID.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Lin Ming <ming.m.lin@intel.com>
CC: Bob Moore <robert.moore@intel.com>
CC: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Len Brown <len.brown@intel.com>
I recently got a system where the DMAR table included a couple of RHSA
(remapping hardware static affinity) entries. Rather than printing a
message about an "Unknown DMAR structure," it would probably be more
useful to dump the RHSA structure (as other DMAR structures are dumped).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We might as well print the type of the DMAR structure we don't know how
to handle when skipping it. Then someone getting this message has a
chance of telling whether the structure is just bogus, or if there
really is something valid that the kernel doesn't know how to handle.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/iommu-2.6: (23 commits)
intel-iommu: Disable PMRs after we enable translation, not before
intel-iommu: Kill DMAR_BROKEN_GFX_WA option.
intel-iommu: Fix integer wrap on 32 bit kernels
intel-iommu: Fix integer overflow in dma_pte_{clear_range,free_pagetable}()
intel-iommu: Limit DOMAIN_MAX_PFN to fit in an 'unsigned long'
intel-iommu: Fix kernel hang if interrupt remapping disabled in BIOS
intel-iommu: Disallow interrupt remapping if not all ioapics covered
intel-iommu: include linux/dmi.h to use dmi_ routines
pci/dmar: correct off-by-one error in dmar_fault()
intel-iommu: Cope with yet another BIOS screwup causing crashes
intel-iommu: iommu init error path bug fixes
intel-iommu: Mark functions with __init
USB: Work around BIOS bugs by quiescing USB controllers earlier
ia64: IOMMU passthrough mode shouldn't trigger swiotlb init
intel-iommu: make domain_add_dev_info() call domain_context_mapping()
intel-iommu: Unify hardware and software passthrough support
intel-iommu: Cope with broken HP DC7900 BIOS
iommu=pt is a valid early param
intel-iommu: double kfree()
intel-iommu: Kill pointless intel_unmap_single() function
...
Fixed up trivial include lines conflict in drivers/pci/intel-iommu.c
The following 64 bit promotions are necessary to handle memory above the
4GiB boundary correctly.
[dwmw2: Fix the second part not to need 64-bit arithmetic at all]
Signed-off-by: Benjamin LaHaise <ben.lahaise@neterion.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If end_pfn is equal to (unsigned long)-1, then the loop will never end.
Seen on 32-bit kernel, but could have happened on 64-bit too once we get
hardware that supports 64-bit guest addresses.
Change both functions to a 'do {} while' loop with the test at the end,
and check for the PFN having wrapper round to zero.
Reported-by: Benjamin LaHaise <ben.lahaise@neterion.com>
Tested-by: Benjamin LaHaise <ben.lahaise@neterion.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This means we're limited to 44-bit addresses on 32-bit kernels, and
makes it sane for us to use 'unsigned long' for PFNs throughout.
Which is just as well, really, since we already do that.
Reported-by: Benjamin LaHaise <ben.lahaise@neterion.com>
Tested-by: Benjamin LaHaise <ben.lahaise@neterion.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since slot_cap field in struct controller contains physical slot
number informationq, we don't need number field in struct slot.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The struct hpc_ops seems a set of hooks to controller specific
routines. But, it is meaningless because no hotplug controller driver
follows this framework.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Since we have a pointer to pcie_device in struct controller, we don't
need a pointer to pci_dev.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The crit_sect mutex defined in struct controller is to serialize
hot-plug operations against multiple slots under the same bus. But,
since PCIe doesnstream port has only one slot at most, it is
meaningless and we don't need it.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The slot number can be calculated only by physical slot number field
in the slot capabilities register. So the first_slot field in struct
controller is meaningless and we don't need it.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Since the device number of the hot-slot under the PCIe downstream port
is always 0, the slot_device_offset field in the slot is meaningless
and we don't need it.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The hp_slot field is to identify the slot under the same
controller. But, since PCIe downstream port has only one slot at most,
it is meaningless and we don't need it.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The device field in the struct slot is not necessary because it is
always 0 in pciehp driver.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The bus field in struct slot is not necessary.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The slot_num_inc field in struct controller is unused and meaningless
in pciehp driver.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Since PCIe downstream port has only one slot at most, we don't need
num_slots field in struct controller. Note that struct controller
itself doesn't exist if PCIe downstream port has no slot.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Since PCIe downstream port has only one slot at most, we don't need
'slot_list' linked list to manage multiple slots under the port.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When booting with pci=nomsi aer causes lost interrupts and
lockdep inversions.
So check if MSIs are not disabled before initializing the aer
driver.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The definition of the ASPM support field in the Link Capabilities
Register had been changed by the "ASPM optionality ECN" as follows:
<Before>
00b Reserved
01b L0s Supported
10b Reserved
11b L0s and L1 Supported
<After>
00b No ASPM Support
01b L0s Supported
10b L1 Supported
11b L0s and L1 Supported
Current linux ASPM driver doesn't enable ASPM if the support field is
00b or 10b. So there is no impact about 00b. But current linux ASPM
driver doesn't enable L1 if the support field is 10b. With this patch,
10b (L1 support) is handled properly.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (75 commits)
PCI hotplug: clean up acpi_run_hpp()
PCI hotplug: acpiphp: use generic pci_configure_slot()
PCI hotplug: shpchp: use generic pci_configure_slot()
PCI hotplug: pciehp: use generic pci_configure_slot()
PCI hotplug: add pci_configure_slot()
PCI hotplug: clean up acpi_get_hp_params_from_firmware() interface
PCI hotplug: acpiphp: don't cache hotplug_params in acpiphp_bridge
PCI hotplug: acpiphp: remove superfluous _HPP/_HPX evaluation
PCI: Clear saved_state after the state has been restored
PCI PM: Return error codes from pci_pm_resume()
PCI: use dev_printk in quirk messages
PCI / PCIe portdrv: Fix pcie_portdrv_slot_reset()
PCI Hotplug: convert acpi_pci_detect_ejectable() to take an acpi_handle
PCI Hotplug: acpiphp: find bridges the easy way
PCI: pcie portdrv: remove unused variable
PCI / ACPI PM: Propagate wake-up enable for devices w/o ACPI support
ACPI PM: Replace wakeup.prepared with reference counter
PCI PM: Introduce device flag wakeup_prepared
PCI / ACPI PM: Rework some debug messages
PCI PM: Simplify PCI wake-up code
...
Fixed up conflict in arch/powerpc/kernel/pci_64.c due to OF device tree
scanning having been moved and merged for the 32- and 64-bit cases. The
'needs_freset' initialization added in 6e19314cc ("PCI/powerpc: support
PCIe fundamental reset") is now in arch/powerpc/kernel/pci_of_scan.c.
* 'x86-txt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, intel_txt: clean up the impact on generic code, unbreak non-x86
x86, intel_txt: Handle ACPI_SLEEP without X86_TRAMPOLINE
x86, intel_txt: Fix typos in Kconfig help
x86, intel_txt: Factor out the code for S3 setup
x86, intel_txt: tboot.c needs <asm/fixmap.h>
intel_txt: Force IOMMU on for Intel TXT launch
x86, intel_txt: Intel TXT Sx shutdown support
x86, intel_txt: Intel TXT reboot/halt shutdown support
x86, intel_txt: Intel TXT boot support
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (52 commits)
Input: bcm5974 - silence uninitialized variables warnings
Input: wistron_btns - add keymap for AOpen 1557
Input: psmouse - use boolean type
Input: i8042 - use platform_driver_probe
Input: i8042 - use boolean type where it makes sense
Input: i8042 - try disabling and re-enabling AUX port at close
Input: pxa27x_keypad - allow modifying keymap from userspace
Input: sunkbd - fix formatting
Input: i8042 - bypass AUX IRQ delivery test on laptops
Input: wacom_w8001 - simplify querying logic
Input: atkbd - allow setting force-release bitmap via sysfs
Input: w90p910_keypad - move a dereference below a NULL test
Input: add twl4030_keypad driver
Input: matrix-keypad - add function to build device keymap
Input: tosakbd - fix cleaning up KEY_STROBEs after error
Input: joydev - validate axis/button maps before clobbering current ones
Input: xpad - add USB ID for the drumkit controller from Rock Band
Input: w90p910_keypad - rename driver name to match platform
Input: add new driver for Sentelic Finger Sensing Pad
Input: psmouse - allow defining read-only attributes
...
This patch cleans up acpi_run_hpp() and follows the style of acpi_run_hpx():
- remove unnecessary METHOD_NAME__HPP #define
- use ACPI_ALLOCATE_BUFFER rather than evaluating _HPP twice
- validate _HPP package length (defined as 4 by the spec)
- avoid ref to undefined data if FW provides < 4 elements
- remove temporary nui[] array
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the generic pci_configure_slot() rather than the acpiphp-specific
decode_hpp() and program_hpp().
Unlike the previous acpiphp-specific code, pci_configure_slot() programs
PCIe settings when an _HPX method provides them, so acpiphp-managed PCIe
devices can now be configured.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the generic pci_configure_slot() rather than the SHPC-specific
program_fw_provided_values().
Unlike the previous SHPC-specific code, pci_configure_slot() programs PCIe
settings when an _HPX method provides them, so if it's possible to have an
SHPC-managed PCIe device, it can now be configured.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the generic pci_configure_slot() rather than the PCIe-specific
program_fw_provided_values().
Unlike the previous pciehp-specific code, we now walk through subordinate
devices even if there are no settings for the parent. This should be
harmless because we won't change anything unless we discover firmware
settings farther down.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds a new pci_configure_slot() function that programs the
PCI bus characteristics for a newly-added device. This is based on
code in pciehp_pci.c, but should be generic enough to be used by pciehp,
shpchp, and acpiphp.
The hotplug_params struct and the program_hpp_typeX() functions are based
on the ACPI definitions, but they aren't really ACPI-specific, and there's
no alternate implementation, so I don't see the need to abstract them yet.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch makes acpi_get_hp_params_from_firmware() take a
pci_dev rather than a pci_bus and makes it return a standard
int errno rather than acpi_status.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We always look up hotplug_params with decode_hpp() immediately before using
them, so we don't need to save them in the acpiphp_bridge struct. This
patch follows the example of program_fw_provided_values() in pciehp_pci.c
and shpchp_pci.c by just keeping the params on the stack while we need them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
decode_hpp() looks up hotplug PCI parameters from ACPI and saves them
in the acpiphp_bridge structure. These parameters (in bridge->hpp) are
only used by the acpiphp_set_hpp_values() -> program_hpp() path. In
that path, we always call decode_hpp() before program_hpp(), so there's
no need to do it in init_bridge_misc().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some PCI devices fail if their standard configuration registers are
restored twice in a row. Prevent this from happening by making
pci_restore_state() clear the saved_state flag of the device right
after the device's standard configuration registers have been
populated with the previously saved values.
Simplify PCI PM callbacks by removing the direct clearing of
state_saved from them, as it shouldn't be necessary any more (except
in pci_pm_thaw(), where it has to be cleared, so that the values saved
during the "freeze" phase of hibernation are not used later by mistake).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Currently pci_pm_resume() always returns 0, which makes the error
variable defined in there a bit pointless. Make pci_pm_resume()
return error codes obtained from drivers' callbacks.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
After commit c82f63e411
(PCI: check saved state before restore) pcie_portdrv_slot_reset()
may not work correctly if dev->error_state is equal to
pci_channel_io_frozen, because dev->state_saved need not be set at
that time. Fix this issue by setting dev->state_saved before
pci_restore_state() is called in pcie_portdrv_slot_reset().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
acpi_pci_detect_ejectable() goes through effort to convert its
struct pci_bus arg to an acpi_handle, but every time we use this
interface, we already have the handle available.
So let's just use the handle instead of converting back and forth.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Instead of constantly evaluating _ADR and _SEG over and over again,
let's simplify our lives by using:
acpi_pci_find_root() for root bridges
acpi_get_pci_dev() for p2p bridges
This change eliminates some copy 'n paste code and also allows us
to simplify some internal interfaces.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (25 commits)
pata_rz1000: use printk_once
ahci: kill @force_restart and refine CLO for ahci_kick_engine()
pata_cs5535: add pci id for AMD based CS5535 controllers
ahci: Add AMD SB900 SATA/IDE controller device IDs
drivers/ata: use resource_size
sata_fsl: Defer non-ncq commands when ncq commands active
libata: add SATA PMP revision information for spec 1.2
libata: fix off-by-one error in ata_tf_read_block()
ahci: Gigabyte GA-MA69VM-S2 can't do 64bit DMA
ahci: make ahci_asus_m2a_vm_32bit_only() quirk more generic
dmi: extend dmi_get_year() to dmi_get_date()
dmi: fix date handling in dmi_get_year()
libata: unbreak TPM filtering by reorganizing ata_scsi_pass_thru()
sata_sis: convert to slave_link
sata_sil24: always set protocol override for non-ATAPI data commands
libata: Export AHCI capabilities
libata: Delegate nonrot flag setting to SCSI
[libata] Add pata_rdc driver for RDC ATA devices
drivers/ata: Remove unnecessary semicolons
libata: remove spindown skipping and warning
...
BIOS clear DMAR table INTR_REMAP flag to disable interrupt remapping. Current
kernel only check interrupt remapping(IR) flag in DRHD's extended capability
register to decide interrupt remapping support or not. But IR flag will not
change when BIOS disable/enable interrupt remapping.
When user disable interrupt remapping in BIOS or BIOS often defaultly disable
interrupt remapping feature when BIOS is not mature.Though BIOS disable
interrupt remapping but intr_remapping_supported function will always report
to OS support interrupt remapping if VT-d2 chipset populated. On this
cases, kernel will continue enable interrupt remapping and result kernel panic.
This bug exist on almost all platforms with interrupt remapping support.
This patch add DMAR table INTR_REMAP flag check before enable interrupt
remapping.
Signed-off-by: Youquan Song <youquan.song@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Current kernel enable interrupt remapping only when all the vt-d unit support
interrupt remapping. So it is reasonable we should also disallow enabling
intr-remapping if there any io-apics that are not listed under vt-d units.
Otherwise we can run into issues.
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Youquan Song <youquan.song@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some PCI devices (not PCI Express), like PCI add-on cards, can
generate PME#, but they don't have any special platform wake-up
support. For this reason, even if they generate PME# to wake up the
system from a sleep state, wake-up events are not generated by the
platform.
It turns out that, at least on some systems, PCI bridges and the PCI
host bridge have ACPI GPEs associated with them that, if enabled to
generate wake-up events, allow the system to wake up if one of the
add-on devices asserts PME# while the system is in a sleep state.
Following this observation, if a PCI device without direct ACPI
wake-up support is prepared to wake up the system during a transition
into a sleep state (eg. suspend to RAM), try to configure the bridges
on the path from the device to the root bridge to wake-up the system.
Reviewed-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce a new PCI device flag, wakeup_prepared, to prevent PCI
wake-up preparation code from being executed twice in a row for the
same device and for the same purpose.
Reviewed-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move a debug message from acpi_pci_sleep_wake() to
acpi_pm_device_sleep_wake() and use the standard dev_*() macros
in there.
Reviewed-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Rework the PCI wake-up code so that it's easier to read without
changing the functionality.
Reviewed-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In general a BIOS may goof or we may hotplug in a hotplug controller.
In either case the kernel needs to reserve resources for plugging
in more devices in the future instead of creating a minimal resource
assignment.
We already do this for cardbus bridges I am just adding a variant
for pcie bridges.
v2: Make testing for pcie hotplug bridges based on a flag.
So far we only set the flag for pcie but a header_quirk
could easily be added for the non-standard pci hotplug
bridges.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There is a very old quirk for the intel E7502 E7320 and E7525 memory
controller hubs that disables usage of msi interrupts on pcie hotplug
bridges of those devices, and disables changing the affinity of irqs.
Today all we have to do to disable msi on a specific device is to set
dev->no_msi, which is much more straightforward than the previous
logic.
The re-running of this fixup after pci hotplug happens below these
devices is totally bogus. All of the state we change is pure software
state and we don't change the hardware at all. Which means hotplug on
the lower devices doesn't have a chance to change this state. So we
can safely remove the special case from the pciehp driver and the pcie
portdriver.
I suspect the special case was someone's expermental debug code that
slipped in. Certainly it isn't mentioned in commit
6fb8880a61510295aece04a542767161f624dffe aka BKrev:
41966101LJ_ogfOU0m2aE6teZfQnuQ where the code first appears.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Multiple bits might be set in the Uncorrectable Error Status
register. But aer_print_error_source() only report a error of
the lowest bit set in the error status register.
So print strings for all bits unmasked and set.
And check First Error Pointer to mark the error occured first.
This FEP is not valid when the corresponing bit of the Uncorrectable
Error Status register is not set, or unimplemented or undefined.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
ERR_{,UN}CORRECTABLE_ERROR_MASK are set of error bits which linux know,
set of PCI_ERR_COR_* and PCI_ERR_UNC_* defined in linux/pci_regs.h.
This masks make aerdrv not to report errors of unknown bit, while aerdrv
have ability to report such undefined errors as "Unknown Error Bit %2d".
OTOH aerdrv_errprint does not have any check of setting in mask register.
So it could report masked wrong error by finding bit in status without
knowing that the bit is masked in the mask register.
This patch changes aerdrv to use mask state in mask register propely
instead of defined/hardcoded ERR_{,UN}CORRECTABLE_ERROR_MASK.
This change prevents aerdrv from reporting masked error, and also enable
reporting unknown errors.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The static buffer errmsg_buff[] is used only for building error
message in fixed format, and is protected by a spinlock.
This patch removes this buffer and the spinlock.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The flag AER_MULTI_ERROR_VALID_FLAG in info->flag does mean that the
root port receives multiple error messages. Error messages can be
posted from different devices, so it does not mean that each reported
device has multiple errors.
If there are multiple error devices and the root port has valid error
source ID, it would be nice to report which device is the error source
reported first.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In case of multiple errors, struct aer_err_info would be reused among
all reported devices. So the info->status should be initialized before
recycled. Otherwise error of one device might be reported as the error
of another device. Also info->flags has similar problem on reporting
TLP header.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Definitions of MASK macros in aerdrv_errprint.c are tricky and unsafe.
For example, AER_AGENT_TRANSMITTER_MASK(_sev, _stat) does work like:
static inline func(int _sev, int _stat)
{
if (_sev == AER_CORRECTABLE)
return (_stat & (PCI_ERR_COR_REP_ROLL|PCI_ERR_COR_REP_TIMER));
else
return (_stat & PCI_ERR_COR_REP_ROLL);
}
In case of else path here, for uncorrectable errors, testing bits in
_stat by PCI_ERR_COR_* does not make sense because _stat should have only
PCI_ERR_UNC_* bits originated in uncorrectable error status register.
But at this time this is safe because uncorrectable error using bit
position same to PCI_ERR_COR_REP_ROLL(= bit position 8) is not defined.
Likewise, AER_AGENT_COMPLETER_MASK is always PCI_ERR_UNC_COMP_ABORT but
it works because bit 15 of correctable error status is not defined.
It means that these MASK macros will turn to be wrong once if new error
is defined. (In fact, bit 15 of correctable is now defined in PCIe 2.1)
This patch changes these MASK macros to be more strict, not to return
PCI_ERR_COR_* bits for uncorrectable error status and vise versa.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add ids module parameter which allows specifying initial IDs for the
pci-stub driver. When built into the kernel, pci-stub is linked
before any real pci drivers and by setting up IDs from initialization
it can prevent built-in drivers from attaching to specific devices.
While at it, make pci_stub_probe() print out about devices it grabbed
to weed out "but my controller isn't being probed" bug reports.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Separate out pci_add_dynid() from store_new_id() and export it so that
in-kernel code can add PCI IDs dynamically. As the function will be
available regardless of HOTPLUG, put it and pull pci_free_dynids()
outside of CONFIG_HOTPLUG.
This will be used by pci-stub to initialize initial IDs via module
param.
While at it, remove bogus get_driver() failure check.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add support for PCI-E 5.0 GT/s in max_bus_speed and cur_bus_speed.
Reviewed-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The L0s state can be managed separately for each direction (upstream
direction and downstream direction) of the link. But in the current
implementation, those are mixed up. With this patch, L0s for each
direction are managed separately.
To maintain three states (upstream direction L0s, downstream L0s and
L1), 'aspm_support', 'aspm_enabled', 'aspm_capable', 'aspm_disable'
and 'aspm_default' fields in struct pcie_link_state are changed to
3-bit from 2-bit. The 'latency' field is separated to two 'latency_up'
and 'latency_dw' fields to maintain exit latencies for each direction
of the link. For L0, 'latency_up.l0' and 'latency_dw.l0' are used to
configure upstream direction L0s and downstream direction L0s
respectively. For L1, larger value of 'latency_up.l1' and
'latency_dw.l1' is considered as L1 exit latency.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In the current implementation, ASPM L0s/L1 is disabled for all links
in the hierarchy if one of the link doesn't meet latency requirement.
But we can partially enable ASPM L0s/L1 on sub-tree in the hierarchy.
This patch allows partial L0s/L1 enablement in the hierarchy. And it
also reduce the calculation cost of ASPM configuration very much.
In the previous implementation, all links were enabled with the same
state. With this patch, enabled state for each link is determined
simply as follows (the 'requested' is from policy_to_aspm_state()).
enabled = requested & (link->aspm_capable & link->aspm_disable)
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce 'aspm_capable' field to maintain the capable ASPM setting of
the link. By the 'aspm_capable', we don't need to recheck latency
every time ASPM policy is changed.
Each bit in 'aspm_capable' is associated to ASPM state (L0S/L1). The
bit is set if the associated ASPM state is supported by the link and
it satisfies the latency requirement (i.e. exit latency < endpoint
acceptable latency). The 'aspm_capable' is updated when
- an endpoint device is added (boot time or hot-plug time)
- an endpoint device is removed (hot-unplug time)
- PCI power state is changed.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce 'aspm_disable' flag to manage disabled ASPM state more
robust way.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix possible NULL dereference in pcie_aspm_exit_link_state(). This
patch also cleanup some code.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove the following check in __pcie_aspm_config_link() because it
nerver be true.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We must not clear bits in 'aspm_enabled' using 'aspm_support', or
'aspm_enabled' and 'aspm_default' might be different from the actual
state. In addtion, 'aspm_default' should be intialized even if
'aspm_support' is 0.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds the most recent additions to the list of 82576 device IDs
to the list of devices needing the SR-IOV quirk.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Background:
Graphic devices are accessed through ranges in I/O or memory space. While most
modern devices allow relocation of such ranges, some "Legacy" VGA devices
implemented on PCI will typically have the same "hard-decoded" addresses as
they did on ISA. For more details see "PCI Bus Binding to IEEE Std 1275-1994
Standard for Boot (Initialization Configuration) Firmware Revision 2.1"
Section 7, Legacy Devices.
The Resource Access Control (RAC) module inside the X server currently does
the task of arbitration when more than one legacy device co-exists on the same
machine. But the problem happens when these devices are trying to be accessed
by different userspace clients (e.g. two server in parallel). Their address
assignments conflict. Therefore an arbitration scheme _outside_ of the X
server is needed to control the sharing of these resources. This document
introduces the operation of the VGA arbiter implemented for Linux kernel.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Tiago Vignatti <tiago.vignatti@nokia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cleanup based on the prototype from Matthew Milcox.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cleanup based on the prototype from Matthew Milcox.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cleanup based on the prototype from Matthew Milcox.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move it from the middle of the function to the end.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Unify msi_free_irqs() and msix_free_all_irqs(), and rename it to a
common void function free_msi_irqs().
And relocate the common function to where the prototype is located now.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The msi_list never have MSI-X's msi_desc while MSI is enabled,
and also it never have MSI's msi_desc while MSI-X is enabled.
This patch remove check for MSI-X entry from the pci_disable_msi(),
referring that pci_disable_msix() does not have any check for MSI
entry.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We already print it out for pci bridges, so also print it out for pci devices.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
http://bugzilla.kernel.org/show_bug.cgi?id=12542 reports that with the
quirk not applied on resume, msi stops working after resuming and mcp78s
ahci fails due to IRQ mis-delivery. Apply it on resume too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peer Chen <pchen@nvidia.com>
Cc: Tj <linux@tjworld.net>
Reported-by: Nicolas Derive <kalon33@ubuntu.com>
Cc: Greg KH <greg@kroah.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Shut off the long standing
linux/drivers/pci/search.c:144: warning: 'pci_find_device' is deprecated (declared at linux/drivers/pci/search.c:136)
linux/drivers/pci/search.c:144: warning: 'pci_find_device' is deprecated (declared at linux/drivers/pci/search.c:136)
warnings that appear on every build when CONFIG_PCI_LEGACY is enabled.
gcc warns for the use in EXPORT_SYMBOL
I moved these to a separate file and disabled the warning in the Makefile for that file.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
One more form factor for Compaq Evo D510, which needs the same quirk
as the other form factors. Apparently there's no hardware monitoring
chip on that one, but SPD EEPROMs, so it's still worth unhiding the
SMBus.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Nuzhna Pomoshch <nuzhna_pomoshch@yahoo.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some devices allow an individual function to be reset without affecting
other functions in the same device: that's what pci_reset_function does.
For devices that have this support, expose reset attribite in sysfs.
This is useful e.g. for virtualization, where a qemu userspace
process wants to reset the device when the guest is reset,
to emulate machine reboot as closely as possible.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We cannot simply call acpi_get_pci_dev() on any random ACPI handle
and hope that it works, because a PCI root bridge may not have
an associated struct pci_dev.
This is allowed per the PCI specification, and is referred to as a
non-materialized bridge.
So, depending on the type of PCI bridge that the handle points to,
use the appropriate interface to return the struct pci_bus correctly.
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
yenta needs this for example.
Acked-by: Matthew Wilcox <willy@linux.intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This was #define'd as 0 on all platforms, so let's get rid of it.
This change makes pci_scan_slot() slightly easier to read.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Luck <tony.luck@intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Conflicts:
arch/x86/kernel/reboot.c
security/Kconfig
Merge reason: resolve the conflicts, bump up from rc3 to rc8.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move tboot.h from asm to linux to fix the build errors of intel_txt
patch on non-X86 platforms. Remove the tboot code from generic code
init/main.c and kernel/cpu.c.
Signed-off-by: Shane Wang <shane.wang@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This file needs to include linux/dmi.h directly rather than relying on
it being pulled in from elsewhere.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
DMAR faults are recorded into a ring of "fault recording registers".
fault_index is a 0-based index into the ring. The code allows the
0-based fault_index to be equal to the total number of fault registers
available from the cap_num_fault_regs() macro, which causes access
beyond the last available register.
Signed-off-by Troy Heber <troy.heber@hp.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
An SR-IOV capable device includes an SR-IOV PCIe capability which
describes the Virtual Function (VF) BAR requirements. A typical SR-IOV
device can support multiple VFs whose BARs must be in a contiguous region,
effectively an array of VF BARs. The BAR reports the size requirement
for a single VF. We calculate the full range needed by simply multiplying
the VF BAR size with the number of possible VFs and create a resource
spanning the full range.
This all seems sane enough except it artificially inflates the alignment
requirement for the VF BAR. The VF BAR need only be aligned to the size
of a single BAR not the contiguous range of VF BARs. This can cause us
to fail to allocate resources for the BAR despite the fact that we
actually have enough space.
This patch adds a thin PCI specific layer over the generic
resource_alignment() function which is aware of the special nature of
VF BARs and does sorting and allocation based on the smaller alignment
requirement.
I recognize that while resource_alignment is generic, it's basically a
PCI helper. An alternative to this patch is to add PCI VF BAR specific
information to struct resource. I opted for the extra layer rather than
adding such PCI specific information to struct resource. This does
have the slight downside that we don't cache the BAR size and re-read
for each alignment query (happens a small handful of times during boot
for each VF BAR).
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Yu Zhao <yu.zhao@intel.com>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
make it use the node from irq_desc.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4A95C392.5050903@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Linux/ACPI core files using internal.h all PREFIX "ACPI: ",
however, not all ACPI drivers use/want it -- and they
should not have to #undef PREFIX to define their own.
Add GPL commment to internal.h while we are there.
This does not change any actual console output,
asside from a whitespace fix.
Signed-off-by: Len Brown <len.brown@intel.com>
Generic support for remapping HPET MSI's by parsing the HPET timer block
device scope in the ACPI DRHD tables. This is needed for platforms
supporting interrupt-remapping and MSI capable HPET timer block.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Jay Fenlason <fenlason@redhat.com>
LKML-Reference: <20090804190729.477649000@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Completed a major update for the acpi_get_object_info external interface.
Changes include:
- Support for variable, unlimited length HID, UID, and CID strings
- Support Processor objects the same as Devices (HID,UID,CID,ADR,STA, etc.)
- Call the _SxW power methods on behalf of a device object
- Determine if a device is a PCI root bridge
- Change the ACPI_BUFFER parameter to ACPI_DEVICE_INFO.
These changes will require an update to all callers of this interface.
See the ACPICA Programmer Reference for details.
Also, update all invocations of acpi_get_object_info interface
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The kcalloc() failure path in iommu_init_domains() calls
free_dmar_iommu(), which assumes that ->domains, ->domain_ids,
and ->lock have been properly initialized.
Add checks in free_[dmar]_iommu to not use ->domains,->domain_ids
if not alloced. Move the lock init to prior to the kcalloc()'s,
so it is valid in free_context_table() when free_dmar_iommu() invokes
it at the end.
Patch based on iommu-2.6,
commit 132032274a
Signed-off-by: Donald Dutile <ddutile@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Mark si_domain_init and iommu_prepare_static_identity_mapping with
__init, to eliminate the following warnings:
WARNING: drivers/pci/built-in.o(.text+0xf1f4): Section mismatch in reference from the function si_domain_init() to the function .init.text:si_domain_work_fn()
The function si_domain_init() references
the function __init si_domain_work_fn().
This is often because si_domain_init lacks a __init
annotation or the annotation of si_domain_work_fn is wrong.
WARNING: drivers/pci/built-in.o(.text+0xe340): Section mismatch in reference from the function iommu_prepare_static_identity_mapping() to the function .init.text:si_domain_init()
The function iommu_prepare_static_identity_mapping() references
the function __init si_domain_init().
This is often because iommu_prepare_static_identity_mapping lacks a __init
annotation or the annotation of si_domain_init is wrong.
Signed-off-by: Matt Kraai <kraai@ftbfs.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Without the check, the config space may be filled with zeros. Though
the driver should try to avoid call restoring before saving, but the
pci layer also should check this.
Also removes the existing check in pci_restore_standard_config, since
it's superfluous with the new check in restore_state.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI hotplug: SGI hotplug: do not use hotplug_slot_attr
PCI hotplug: SGI hotplug: fix build failure
All callers of the former were also calling the latter, in one order or
the other, and failing to correctly clean up if the second returned
failure.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
By the pci slot changes, callbacks of attributes under slot directory
(/sys/bus/pci/slots) had been changed to get the pointer to struct
pci_slot instead of struct hotplug_slot. So the path_show() that
assumes the parameter is a pointer to struct hotplug_slot seems
broken.
Tested-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The commit bd3d99c170 ("PCI: Remove
untested Electromechanical Interlock (EMI) support in pciehp."), which
removes the definition of "struct hotplug_slot_attr", broke SGI
hotplug driver. By this commit, we get the following compile error.
drivers/pci/hotplug/sgi_hotplug.c:106: error: variable 'sn_slot_path_attr' has initializer but incomplete type
drivers/pci/hotplug/sgi_hotplug.c:106: error: unknown field 'attr' specified in initializer
drivers/pci/hotplug/sgi_hotplug.c:106: error: extra brace group at end of initializer
drivers/pci/hotplug/sgi_hotplug.c:106: error: (near initialization for 'sn_slot_path_attr')
drivers/pci/hotplug/sgi_hotplug.c:106: warning: excess elements in struct initializer
drivers/pci/hotplug/sgi_hotplug.c:106: warning: (near initialization for 'sn_slot_path_attr')
drivers/pci/hotplug/sgi_hotplug.c:106: error: unknown field 'show' specified in initializer
drivers/pci/hotplug/sgi_hotplug.c:106: warning: excess elements in struct initializer
drivers/pci/hotplug/sgi_hotplug.c:106: warning: (near initialization for 'sn_slot_path_attr')
drivers/pci/hotplug/sgi_hotplug.c: In function 'sn_hp_destroy':
drivers/pci/hotplug/sgi_hotplug.c:203: error: invalid use of undefined type 'struct hotplug_slot_attribute'
drivers/pci/hotplug/sgi_hotplug.c: In function 'sn_hotplug_slot_register':
drivers/pci/hotplug/sgi_hotplug.c:655: error: invalid use of undefined type 'struct hotplug_slot_attribute'
This patch fixes this regression by adding the definition of struct
hotplug_slot_attr into sgi_hotplug.c.
Tested-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Two defects work together result in KVM device passthrough randomly can't
work:
1. iommu_snooping is not initialized to zero when vm_iommu_init() called.
So it is possible to get a random value.
2. One line added by commit 2c2e2c38("IOMMU Identity Mapping Support")
change the code path, let it bypass domain_update_iommu_cap(), as well as
missing the increment of domain iommu reference count.
The latter is also likely to cause a leak of domains on repeated VMM
assignment and deassignment.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The physical address passed to domain_pfn_mapping() should be rounded
down to the start of the MM page, not the VT-d page.
This issue causes kernel panic on PAGE_SIZE>VTD_PAGE_SIZE platforms e.g. ia64
platforms.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In domain_sg_mapping(), use aligned_nrpages() instead of hand-coded
rounding code for calculating the size of each sg elem. This means that
on IA64 we correctly round up to the MM page size, not just to the VT-d
page size.
Also remove the incorrect mm_to_dma_pfn() when intel_map_sg() calls
domain_sg_mapping() -- the 'size' variable is in VT-d pages already.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This makes the hardware passthrough mode work a lot more like the
software version, so that the behaviour of a kernel with 'iommu=pt'
is the same whether the hardware supports passthrough or not.
In particular:
- We use a single si_domain for the pass-through devices.
- 32-bit devices can be taken out of the pass-through domain so that
they don't have to use swiotlb.
- Devices will work again after being removed from a KVM guest.
- A potential oops on OOM (in init_context_pass_through()) is fixed.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Yet another reason why trusting this stuff to the BIOS was a bad idea.
The HP DC7900 BIOS reports an iommu at an address which just returns all
ones, when VT-d is disabled in the BIOS.
Fix up the missing iounmap in the error paths while we're at it.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This function has traditionally used "insert_resource()", because before
commit cebd78a8c5 ("Fix pci_claim_resource") it used to just insert the
resource into whatever root resource tree that was indicated by
"pcibios_select_root()".
So there Matthew fixed it to actually look up the proper parent
resource, which means that now it's actively wrong to then traverse the
resource tree any more: we already know exactly where the new resource
should go.
And when we then did commit a76117dfd6 ("x86: Use pci_claim_resource"),
which changed the x86 PCI code from the open-coded
pr = pci_find_parent_resource(dev, r);
if (!pr || request_resource(pr, r) < 0) {
to using
if (pci_claim_resource(dev, idx) < 0) {
that "insert_resource()" now suddenly became a problem, and causes a
regression covered by
http://bugzilla.kernel.org/show_bug.cgi?id=13891
which this fixes.
Reported-and-tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Andrew Patterson <andrew.patterson@hp.com>
Cc: Linux PCI <linux-pci@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
They are not supposed to be modified by drivers, so make them const.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The tboot module will DMA protect all of memory in order to ensure the that
kernel will be able to initialize without compromise (from DMA). Consequently,
the kernel must enable Intel Virtualization Technology for Directed I/O
(VT-d or Intel IOMMU) in order to replace this broad protection with the
appropriate page-granular protection. Otherwise DMA devices will be unable
to read or write from memory and the kernel will eventually panic.
Because runtime IOMMU support is configurable by command line options, this
patch will force it to be enabled regardless of the options specified, and will
log a message if it was required to force it on.
dmar.c | 7 +++++++
intel-iommu.c | 17 +++++++++++++++--
2 files changed, 22 insertions(+), 2 deletions(-)
Signed-off-by: Joseph Cihula <joseph.cihula@intel.com>
Signed-off-by: Shane Wang <shane.wang@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
g_iommus is freed after we "goto error;".
Found by smatch (http://repo.or.cz/w/smatch.git).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We only ever obtain this lock immediately before the iova_rbtree_lock,
and release it immediately after the iova_rbtree_lock. So ditch it and
just use iova_rbtree_lock.
[v2: Remove the lockdep bits this time too]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After some API change, intel_iommu_unmap_range() introduced a assumption that
parameter size != 0, otherwise the dma_pte_clean_range() would have a
overflowed argument. But the user like KVM don't have this assumption before,
then some BUG() triggered.
Fix it by ignoring size = 0.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We did before, in the end -- but it was at the bottom of a long stack of
functions. Add an inline wrapper get_valid_domain_for_dev() which will
use the cached one _first_ and only make the out-of-line call if it's
not already set.
This takes the average time taken for a 1-page intel_map_sg() from 5961
cycles to 4812 cycles on my Lenovo x200s test box -- a modest 20%.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: Fix IRQ swizzling for ARI-enabled devices
ia64/PCI: adjust section annotation for pcibios_setup()
x86/PCI: get root CRS before scanning children
x86/PCI: fix boundary checking when using root CRS
PCI MSI: Fix restoration of MSI/MSI-X mask states in suspend/resume
PCI MSI: Unmask MSI if setup failed
PCI MSI: shorten PCI_MSIX_ENTRY_* symbol names
PCI: make pci_name() take const argument
PCI: More PATA quirks for not entering D3
PCI: fix kernel-doc warnings
PCI: check if bus has a proper bridge device before triggering SBR
PCI: remove pci_dac_dma_... APIs on mn10300
PCI ECRC: Remove unnecessary semicolons
PCI MSI: Return if alloc_msi_entry for MSI-X failed
Our current strategy for pass-through mode is to put all devices into
the 1:1 domain at startup (which is before we know what their dma_mask
will be), and only _later_ take them out of that domain, if it turns out
that they really can't address all of memory.
However, when there are a bunch of PCI devices behind a bridge, they all
end up with the same source-id on their DMA transactions, and hence in
the same IOMMU domain. This means that we _can't_ easily move them from
the 1:1 domain into their own domain at runtime, because there might be DMA
in-flight from their siblings.
So we have to adjust our pass-through strategy: For PCI devices not on
the root bus, and for the bridges which will take responsibility for
their transactions, we have to start up _out_ of the 1:1 domain, just in
case.
This fixes the BUG() we see when we have 32-bit-capable devices behind a
PCI-PCI bridge, and use the software identity mapping.
It does mean that we might end up using 'normal' mapping mode for some
devices which could actually live with the faster 1:1 mapping -- but
this is only for PCI devices behind bridges, which presumably aren't the
devices for which people are most concerned about performance.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
At boot time, the dma_mask won't have been set on any devices, so we
assume that all devices will be 64-bit capable (and thus get a 1:1 map).
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This should fix kernel.org bug #11821, where the dcdbas driver makes up
a platform device and then uses dma_alloc_coherent() on it, in an
attempt to get memory < 4GiB.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We need to give people a little more time to fix the broken drivers.
Re-introduce this, but tied in properly with the 'iommu=pt' support this
time. Change the config option name and make it default to 'no' too.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We do this twice, and it's about to get more complicated. This makes the
code slightly clearer about what it's doing, too.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When we reattach a device to the si_domain (because it's been removed
from a VM), we weren't calling domain_context_mapping() to actually tell
the hardware about that.
We should really put the call to domain_context_mapping() into
domain_add_dev_info() -- we never call the latter without also doing the
former, and we can keep the error paths simple that way. But that's a
cleanup which can wait for 2.6.32 now.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We should check iommu_dummy() _first_, because that means it's attached
to an iommu that we've just disabled completely. At the moment, we might
try to put the device into the identity mapping domain.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The aligned_nrpages() function rounds up to the next VM page, but
returns its result as a number of DMA pages.
Purely theoretical except on IA64, which doesn't boot with VT-d right
now anyway.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/iommu-2.6: (38 commits)
intel-iommu: Don't keep freeing page zero in dma_pte_free_pagetable()
intel-iommu: Introduce first_pte_in_page() to simplify PTE-setting loops
intel-iommu: Use cmpxchg64_local() for setting PTEs
intel-iommu: Warn about unmatched unmap requests
intel-iommu: Kill superfluous mapping_lock
intel-iommu: Ensure that PTE writes are 64-bit atomic, even on i386
intel-iommu: Make iommu=pt work on i386 too
intel-iommu: Performance improvement for dma_pte_free_pagetable()
intel-iommu: Don't free too much in dma_pte_free_pagetable()
intel-iommu: dump mappings but don't die on pte already set
intel-iommu: Combine domain_pfn_mapping() and domain_sg_mapping()
intel-iommu: Introduce domain_sg_mapping() to speed up intel_map_sg()
intel-iommu: Simplify __intel_alloc_iova()
intel-iommu: Performance improvement for domain_pfn_mapping()
intel-iommu: Performance improvement for dma_pte_clear_range()
intel-iommu: Clean up iommu_domain_identity_map()
intel-iommu: Remove last use of PHYSICAL_PAGE_MASK, for reserving PCI BARs
intel-iommu: Make iommu_flush_iotlb_psi() take pfn as argument
intel-iommu: Change aligned_size() to aligned_nrpages()
intel-iommu: Clean up intel_map_sg(), remove domain_page_mapping()
...
Check dma_pte_present() and only free the page if there _is_ one.
Kind of surprising that there was no warning about this.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
On Wed, 2009-07-01 at 16:59 -0700, Linus Torvalds wrote:
> I also _really_ hate how you do
>
> (unsigned long)pte >> VTD_PAGE_SHIFT ==
> (unsigned long)first_pte >> VTD_PAGE_SHIFT
Kill this, in favour of just looking to see if the incremented pte
pointer has 'wrapped' onto the next page. Which means we have to check
it _after_ incrementing it, not before.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
For many purposes, including interrupt-swizzling, devices with ARI
enabled behave as if they have one device (number 0) and 256 functions.
This probably hasn't bitten us in practice because all ARI devices I've
seen are also IOV devices, and IOV devices are required to use MSI.
This isn't guaranteed, and there are legitimate reasons to use ARI
without IOV, and hence potentially use pin-based interrupts.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This would have found the bug in i386 pci_unmap_addr() a long time ago.
We shouldn't just silently return without doing anything.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since we're using cmpxchg64() anyway (because that's the only way to do
an atomic 64-bit store on i386), we might as well ditch the extra
locking and just use cmpxchg64() to ensure that we don't add the page
twice.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This fixes kernel.org bug #13584. The IOVA code attempted to optimise
the insertion of new ranges into the rbtree, with the unfortunate result
that some ranges just didn't get inserted into the tree at all. Then
those ranges would be handed out more than once, and things kind of go
downhill from there.
Introduced after 2.6.25 by ddf02886cb
("PCI: iova RB tree setup tweak").
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: mark gross <mgross@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As with other functions, batch the CPU data cache flushes and don't keep
recalculating PTE addresses.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The loop condition was wrong -- we should free a PMD only if its
_entire_ range is within the range we're intending to clear. The
early-termination condition was right, but not the loop.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Instead of calling domain_pfn_mapping() repeatedly with single or
small numbers of pages, just pass the sglist in. It can optimise the
number of cache flushes like domain_pfn_mapping() does, and gives a huge
speedup for large scatterlists.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There are 2 problems on mask states in suspend/resume.
[1]:
It is better to restore the mask states of MSI/MSI-X to initial states
(MSI is unmasked, MSI-X is masked) when we release the device.
The pci_msi_shutdown() does the restoration of mask states for MSI,
while the msi_free_irqs() does it for MSI-X. In other words, in the
"disable" path both of MSI and MSI-X are handled, but in the "shutdown"
path only MSI is handled.
MSI:
pci_disable_msi()
=> pci_msi_shutdown()
[ mask states for MSI restored ]
=> msi_set_enable(dev, pos, 0);
=> msi_free_irqs()
MSI-X:
pci_disable_msix()
=> pci_msix_shutdown()
=> msix_set_enable(dev, 0);
=> msix_free_all_irqs
=> msi_free_irqs()
[ mask states for MSI-X restored ]
This patch moves the masking for MSI-X from msi_free_irqs() to
pci_msix_shutdown().
This change has some positive side effects:
- It prevents OS from touching mask states before reading preserved
bits in the register, which can be happen if msi_free_irqs() is
called from error path in msix_capability_init().
- It also prevents touching the register after turning off MSI-X in
"disable" path, which can be a problem on some devices.
[2]:
We have cache of the mask state in msi_desc, which is automatically
updated when msi/msix_mask_irq() is called. This cached states are
used for the resume.
But since what need to be restored in the resume is the states before
the shutdown on the suspend, calling msi/msix_mask_irq() from
pci_msi/msix_shutdown() is not appropriate.
This patch introduces __msi/msix_mask_irq() that do mask as same
as msi/msix_mask_irq() but does not update cached state, for use
in pci_msi/msix_shutdown().
[updated: get rid of msi/msix_mask_irq_nocache() (proposed by Matthew Wilcox)]
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The initial state of mask register of MSI is unmasked. We set it
masked before calling arch_setup_msi_irqs(). If arch_setup_msi_irq()
fails, it is better to restore the state of the mask register.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These names are too long! Drop _OFFSET to save some bytes/lines.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The ALi loses some state if it goes into D3. Unfortunately even with the
chipset documents I can't figure out how to restore some bits of it.
The VIA one saves/restores apparently fine but the ACPI _GTM methods break
on some platforms if we do this and this causes cable misdetections.
These are both effectively regressions as historically nothing matched the
devices and then decided not to bind to them. Nowdays something is binding
to all sorts of devices and a result they get dumped into D3.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For devices attached to the root bus, we can't trigger Secondary Bus
Reset because there is no bridge device associated with the bus. So
need to check bus->self again NULL first before using it.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Kenji Kaneshige