Combining RO and AH/ESP/IPCOMP does not make sense. So this patch adds a
check in the state initialisation function to prevent this.
This allows us to safely remove the mode input function of RO since it
can never be called anymore. Indeed, if somehow it does get called we'll
know about it through an OOPS instead of it slipping past silently.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv6 calling convention for x->mode->output is more general and could
help an eventual protocol-generic x->type->output implementation. This
patch adopts it for IPv4 as well and modifies the IPv4 type output functions
accordingly.
It also rewrites the IPv6 mac/transport header calculation to be based off
the network header where practical.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the calling convention so that on entry from
x->mode->output and before entry into x->type->output skb->data
will point to the payload instead of the IP header.
This is essentially a redistribution of skb_push/skb_pull calls
with the aim of minimising them on the common path of tunnel +
ESP.
It'll also let us use the same calling convention between IPv4
and IPv6 with the next patch.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current the x->mode->output functions store the IPv6 nh pointer in the
skb network header. This is inconvenient because the network header then
has to be fixed up before the packet can leave the IPsec stack. The mac
header field is unused on output so we can use that to store this instead.
This patch does that and removes the network header fix-up in xfrm_output.
It also uses ipv6_hdr where appropriate in the x->type->output functions.
There is also a minor clean-up in esp4 to make it use the same code as
esp6 to help any subsequent effort to merge the two.
Lastly it kills two redundant skb_set_* statements in BEET that were
simply copied over from transport mode.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lastused update check in xfrm_output can be done just as well in
the mode output function which is specific to RO.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the cases where the transport header is being set to a offset from
skb->data.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the skb->nh union has just one member, .raw, i.e. it is just like the
skb->mac union, strange, no? I'm just leaving it like that till the transport
layer is done with, when we'll rename skb->mac.raw to skb->mac_header (or
->mac_header_offset?), ditto for ->{h,nh}.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose IPSEC modes output path to take an xfrm state as input param.
This makes it consistent with the input mode processing (which already
takes the xfrm state as a param).
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Route optimization is used with routing header and destination options
header for Mobile IPv6.
At outbound it makes header space like IPsec transport. At inbound it
does nothing because exhdrs.c functions have responsibility to update
skbuff information for these headers.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu