Now that all call sites are using the slot number to modify item values,
rename the SETGET helpers to raw_item_*(), and then rework the _nr()
helpers to be the btrfs_item_*() btrfs_set_item_*() helpers, and then
rename all of the callers to the new helpers.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
During a verity rollback, if we fail to update the inode or delete the
orphan, we abort the transaction and return without releasing our
transaction handle. Fix that by releasing the handle.
Fixes: 146054090b ("btrfs: initial fsverity support")
Fixes: 705242538f ("btrfs: verity metadata orphan items")
Reviewed-by: Boris Burkov <boris@bur.io>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Writing out the verity data is too large of an operation to do in a
single transaction. If we are interrupted before we finish creating
fsverity metadata for a file, or fail to clean up already created
metadata after a failure, we could leak the verity items that we already
committed.
To address this issue, we use the orphan mechanism. When we start
enabling verity on a file, we also add an orphan item for that inode.
When we are finished, we delete the orphan. However, if we are
interrupted midway, the orphan will be present at mount and we can
cleanup the half-formed verity state.
There is a possible race with a normal unlink operation: if unlink and
verity run on the same file in parallel, it is possible for verity to
succeed and delete the still legitimate orphan added by unlink. Then, if
we are interrupted and mount in that state, we will never clean up the
inode properly. This is also possible for a file created with O_TMPFILE.
Check nlink==0 before deleting to avoid this race.
A final thing to note is that this is a resurrection of using orphans to
signal an operation besides "delete this inode". The old case was to
signal the need to do a truncate. That case still technically applies
for mounting very old file systems, so we need to take some care to not
clobber it. To that end, we just have to be careful that verity orphan
cleanup is a no-op for non-verity files.
Signed-off-by: Boris Burkov <boris@bur.io>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Add support for fsverity in btrfs. To support the generic interface in
fs/verity, we add two new item types in the fs tree for inodes with
verity enabled. One stores the per-file verity descriptor and btrfs
verity item and the other stores the Merkle tree data itself.
Verity checking is done in end_page_read just before a page is marked
uptodate. This naturally handles a variety of edge cases like holes,
preallocated extents, and inline extents. Some care needs to be taken to
not try to verity pages past the end of the file, which are accessed by
the generic buffered file reading code under some circumstances like
reading to the end of the last page and trying to read again. Direct IO
on a verity file falls back to buffered reads.
Verity relies on PageChecked for the Merkle tree data itself to avoid
re-walking up shared paths in the tree. For this reason, we need to
cache the Merkle tree data. Since the file is immutable after verity is
turned on, we can cache it at an index past EOF.
Use the new inode ro_flags to store verity on the inode item, so that we
can enable verity on a file, then rollback to an older kernel and still
mount the file system and read the file. Since we can't safely write the
file anymore without ruining the invariants of the Merkle tree, we mark
a ro_compat flag on the file system when a file has verity enabled.
Acked-by: Eric Biggers <ebiggers@google.com>
Co-developed-by: Chris Mason <clm@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Boris Burkov <boris@bur.io>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik