There is no need to check if the cpufreq driver implements callback
cpufreq_driver::target_index. The logic in the __resolve_freq uses
the frequency table available in the policy. It doesn't matter if the
driver provides 'target_index' or 'target' callback. It just has to
populate the 'policy->freq_table'.
Thus, check only frequency table during the frequency resolving call.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Fix return error code in mtk_cpu_dvfs_info_init (Yang Yingliang).
- Minor cleanups and support for new boards for Qcom cpufreq drivers
(Bryan O'Donoghue, Konrad Dybcio, Pierre Gondois, and Yicong Yang).
- Fix sparse warnings for Tegra cpufreq driver (Viresh Kumar).
- Make dev_pm_opp_set_regulators() accept NULL terminated list (Viresh
Kumar).
- Add dev_pm_opp_set_config() and friends and migrate other users and
helpers to using them (Viresh Kumar).
- Add support for multiple clocks for a device (Viresh Kumar and
Krzysztof Kozlowski).
- Configure resources before adding OPP table for Venus (Stanimir
Varbanov).
- Keep reference count up for opp->np and opp_table->np while they are
still in use (Liang He).
- Minor OPP cleanups (Viresh Kumar and Yang Li).
- Add a trace event for cpuidle to track missed (too deep or too
shallow) wakeups (Kajetan Puchalski).
-----BEGIN PGP SIGNATURE-----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=LBb0
-----END PGP SIGNATURE-----
Merge tag 'pm-5.20-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These are ARM cpufreq updates and operating performance points (OPP)
updates plus one cpuidle update adding a new trace point.
Specifics:
- Fix return error code in mtk_cpu_dvfs_info_init (Yang Yingliang).
- Minor cleanups and support for new boards for Qcom cpufreq drivers
(Bryan O'Donoghue, Konrad Dybcio, Pierre Gondois, and Yicong Yang).
- Fix sparse warnings for Tegra cpufreq driver (Viresh Kumar).
- Make dev_pm_opp_set_regulators() accept NULL terminated list
(Viresh Kumar).
- Add dev_pm_opp_set_config() and friends and migrate other users and
helpers to using them (Viresh Kumar).
- Add support for multiple clocks for a device (Viresh Kumar and
Krzysztof Kozlowski).
- Configure resources before adding OPP table for Venus (Stanimir
Varbanov).
- Keep reference count up for opp->np and opp_table->np while they
are still in use (Liang He).
- Minor OPP cleanups (Viresh Kumar and Yang Li).
- Add a trace event for cpuidle to track missed (too deep or too
shallow) wakeups (Kajetan Puchalski)"
* tag 'pm-5.20-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (55 commits)
cpuidle: Add cpu_idle_miss trace event
venus: pm_helpers: Fix warning in OPP during probe
OPP: Don't drop opp->np reference while it is still in use
OPP: Don't drop opp_table->np reference while it is still in use
cpufreq: tegra194: Staticize struct tegra_cpufreq_soc instances
dt-bindings: cpufreq: cpufreq-qcom-hw: Add SM6375 compatible
dt-bindings: opp: Add msm8939 to the compatible list
dt-bindings: opp: Add missing compat devices
dt-bindings: opp: opp-v2-kryo-cpu: Fix example binding checks
cpufreq: Change order of online() CB and policy->cpus modification
cpufreq: qcom-hw: Remove deprecated irq_set_affinity_hint() call
cpufreq: qcom-hw: Disable LMH irq when disabling policy
cpufreq: qcom-hw: Reset cancel_throttle when policy is re-enabled
cpufreq: qcom-cpufreq-hw: use HZ_PER_KHZ macro in units.h
cpufreq: mediatek: fix error return code in mtk_cpu_dvfs_info_init()
OPP: Remove dev{m}_pm_opp_of_add_table_noclk()
PM / devfreq: tegra30: Register config_clks helper
OPP: Allow config_clks helper for single clk case
OPP: Provide a simple implementation to configure multiple clocks
OPP: Assert clk_count == 1 for single clk helpers
...
Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text. Also included in here are a few other minor updates,
2 USB files, and one Documentation file update to get the SPDX lines
correct.
All of these have been in the linux-next tree for a very long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYupz3g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynPUgCgslaf2ssCgW5IeuXbhla+ZBRAzisAnjVgOvLN
4AKdqbiBNlFbCroQwmeQ
=v1sg
-----END PGP SIGNATURE-----
Merge tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
- Make dev_pm_opp_set_regulators() accept NULL terminated list (Viresh
Kumar).
- Add dev_pm_opp_set_config() and friends and migrate other
users/helpers to using them (Viresh Kumar).
- Add support for multiple clocks for a device (Viresh Kumar and
Krzysztof Kozlowski).
- Configure resources before adding OPP table for Venus (Stanimir
Varbanov).
- Keep reference count up for opp->np and opp_table->np while they are
still in use (Liang He).
- Minor cleanups (Viresh Kumar and Yang Li).
-----BEGIN PGP SIGNATURE-----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=NHBQ
-----END PGP SIGNATURE-----
Merge tag 'opp-updates-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Pull operating performance points (OPP) updates for 5.20-rc1 from Viresh
Kumar:
"- Make dev_pm_opp_set_regulators() accept NULL terminated list (Viresh
Kumar).
- Add dev_pm_opp_set_config() and friends and migrate other
users/helpers to using them (Viresh Kumar).
- Add support for multiple clocks for a device (Viresh Kumar and
Krzysztof Kozlowski).
- Configure resources before adding OPP table for Venus (Stanimir
Varbanov).
- Keep reference count up for opp->np and opp_table->np while they are
still in use (Liang He).
- Minor cleanups (Viresh Kumar and Yang Li)."
* tag 'opp-updates-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm: (43 commits)
venus: pm_helpers: Fix warning in OPP during probe
OPP: Don't drop opp->np reference while it is still in use
OPP: Don't drop opp_table->np reference while it is still in use
OPP: Remove dev{m}_pm_opp_of_add_table_noclk()
PM / devfreq: tegra30: Register config_clks helper
OPP: Allow config_clks helper for single clk case
OPP: Provide a simple implementation to configure multiple clocks
OPP: Assert clk_count == 1 for single clk helpers
OPP: Add key specific assert() method to key finding helpers
OPP: Compare bandwidths for all paths in _opp_compare_key()
OPP: Allow multiple clocks for a device
dt-bindings: opp: accept array of frequencies
OPP: Make dev_pm_opp_set_opp() independent of frequency
OPP: Reuse _opp_compare_key() in _opp_add_static_v2()
OPP: Remove rate_not_available parameter to _opp_add()
OPP: Use consistent names for OPP table instances
OPP: Use generic key finding helpers for bandwidth key
OPP: Use generic key finding helpers for level key
OPP: Add generic key finding helpers and use them for freq APIs
OPP: Remove dev_pm_opp_find_freq_ceil_by_volt()
...
- Fix return error code in mtk_cpu_dvfs_info_init (Yang Yingliang).
- Minor cleanups and support for new boards for Qcom cpufreq drivers
(Bryan O'Donoghue, Konrad Dybcio, Pierre Gondois, and Yicong Yang).
- Fix sparse warnings for Tegra driver (Viresh Kumar).
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEx73Crsp7f6M6scA70rkcPK6BEhwFAmLoqRYACgkQ0rkcPK6B
EhzcNA/6A52UpkbXwfd63B+hCeLPTjjvnn+Z1FeRUG+ymbEDcMYQ7Z+ae3clKQ86
MmkK9UkYae50riCz9lv10UihI5JtxVkyCiCvgASxmRAvKrbODqSOu0UmMKR+CwJ/
GryoB8xCL/aAencyb3qin4fZHlwdjqBP7mgRQtoRbxjT0liFonauoG84DPhWhgMi
i22V83j4pZpDIPyfNN9AvBOiaGXx3n3zG0ODx1E7Y7P9Eg/3n1AdRPST3C4Y4y3X
79WbwBur13NKi9Ww5jw5guRKehNC8l79Ly80UQ4pRg2y4RtmyABX9qteOfvbj9Ix
JFWV+EdDLhU+mk1hHMx3GzFDWsaUYS+ZrS9oDREZ06LkN1ZDf5OFOP8nxr7SRvSD
3ZYlVA2IClt1Q//GsRiGy7kJK1qFtWVVWEE/NHS27W6VorugoHiyfNx8jYYBaOez
bNyrKklYlIFsgkRoVG0e2/2ZrzCeTVZLjsFl9992pnoDG8Fv9fBUpsHQajLkolJ4
KSZ35sxSvMzREKtuy4g8XeV2l9cES5FZ6B2iGqVo2BuoJdyqMfcQqtOyVbXAlkOz
pXSPxVuNr5w9uVQhuE0cSAiqe6joMgE5jT+5A2dIThC34nRzDLTrmQohR31nDZRj
nCsb3Pkee6j8DVwGVSNFuVJ0xvOnw1Sk8RCidiKZ9+Otu/blqaM=
=fX64
-----END PGP SIGNATURE-----
Merge tag 'cpufreq-arm-updates-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Pull cpufreq/ARM updates for 5.20-rc1 from Viresh Kumar:
"- Fix return error code in mtk_cpu_dvfs_info_init (Yang Yingliang).
- Minor cleanups and support for new boards for Qcom cpufreq drivers
(Bryan O'Donoghue, Konrad Dybcio, Pierre Gondois, and Yicong Yang).
- Fix sparse warnings for Tegra driver (Viresh Kumar)."
* tag 'cpufreq-arm-updates-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: tegra194: Staticize struct tegra_cpufreq_soc instances
dt-bindings: cpufreq: cpufreq-qcom-hw: Add SM6375 compatible
dt-bindings: opp: Add msm8939 to the compatible list
dt-bindings: opp: Add missing compat devices
dt-bindings: opp: opp-v2-kryo-cpu: Fix example binding checks
cpufreq: Change order of online() CB and policy->cpus modification
cpufreq: qcom-hw: Remove deprecated irq_set_affinity_hint() call
cpufreq: qcom-hw: Disable LMH irq when disabling policy
cpufreq: qcom-hw: Reset cancel_throttle when policy is re-enabled
cpufreq: qcom-cpufreq-hw: use HZ_PER_KHZ macro in units.h
cpufreq: mediatek: fix error return code in mtk_cpu_dvfs_info_init()
Merge core device power management changes for v5.20-rc1:
- Extend support for wakeirq to callback wrappers used during system
suspend and resume (Ulf Hansson).
- Defer waiting for device probe before loading a hibernation image
till the first actual device access to avoid possible deadlocks
reported by syzbot (Tetsuo Handa).
- Unify device_init_wakeup() for PM_SLEEP and !PM_SLEEP (Bjorn
Helgaas).
- Add Raptor Lake-P to the list of processors supported by the Intel
RAPL driver (George D Sworo).
- Add Alder Lake-N and Raptor Lake-P to the list of processors for
which Power Limit4 is supported in the Intel RAPL driver (Sumeet
Pawnikar).
- Make pm_genpd_remove() check genpd_debugfs_dir against NULL before
attempting to remove it (Hsin-Yi Wang).
- Change the Energy Model code to represent power in micro-Watts and
adjust its users accordingly (Lukasz Luba).
* pm-core:
PM: runtime: Extend support for wakeirq for force_suspend|resume
* pm-sleep:
PM: hibernate: defer device probing when resuming from hibernation
PM: wakeup: Unify device_init_wakeup() for PM_SLEEP and !PM_SLEEP
* powercap:
powercap: RAPL: Add Power Limit4 support for Alder Lake-N and Raptor Lake-P
powercap: intel_rapl: Add support for RAPTORLAKE_P
* pm-domains:
PM: domains: Ensure genpd_debugfs_dir exists before remove
* pm-em:
cpufreq: scmi: Support the power scale in micro-Watts in SCMI v3.1
firmware: arm_scmi: Get detailed power scale from perf
Documentation: EM: Switch to micro-Watts scale
PM: EM: convert power field to micro-Watts precision and align drivers
A cpumask structure on the stack can cause a warning with
CONFIG_NR_CPUS=8192 (e.g. Ubuntu 22.04 uses this):
drivers/cpufreq/cpufreq_ondemand.c: In function 'od_set_powersave_bias':
drivers/cpufreq/cpufreq_ondemand.c:449:1: warning: the frame size of
1032 bytes is larger than 1024 bytes [-Wframe-larger-than=]
449 | }
| ^
CONFIG_CPUMASK_OFFSTACK=y is enabled by default for most distros, and
hence we can work around the warning by using cpumask_var_t.
Signed-off-by: Zhao Liu <zhao1.liu@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use the possessive "its" instead of the contraction "it's"
where appropriate.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
From a state where all policy->related_cpus are offline, putting one
of the policy's CPU back online re-activates the policy by:
1. Calling cpufreq_driver->online()
2. Setting the CPU in policy->cpus
qcom_cpufreq_hw_cpu_online() makes use of policy->cpus. Thus 1. and 2.
should be inverted to avoid having a policy->cpus empty. The
qcom-cpufreq-hw is the only driver affected by this.
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
With the new design in place, the show() and store() callbacks check if
the policy is active or not before proceeding any further to avoid
potential races. And in order to guarantee that cpufreq_policy_free()
must be called after clearing the policy->cpus mask, i.e. by marking the
policy inactive.
In order to avoid introducing a bug around this later, print a warning
message if we end up freeing an active policy.
Also update cpufreq_online() a bit to make sure we clear the cpus mask
for each error case before calling cpufreq_policy_free().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The SCMI v3.1 adds support for power values in micro-Watts. They are not
always in milli-Watts anymore (ignoring the bogo-Watts). Thus, the power
must be converted conditionally before sending to Energy Model. Add the
logic which handles the needed checks and conversions.
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The milli-Watts precision causes rounding errors while calculating
efficiency cost for each OPP. This is especially visible in the 'simple'
Energy Model (EM), where the power for each OPP is provided from OPP
framework. This can cause some OPPs to be marked inefficient, while
using micro-Watts precision that might not happen.
Update all EM users which access 'power' field and assume the value is
in milli-Watts.
Solve also an issue with potential overflow in calculation of energy
estimation on 32bit machine. It's needed now since the power value
(thus the 'cost' as well) are higher.
Example calculation which shows the rounding error and impact:
power = 'dyn-power-coeff' * volt_mV * volt_mV * freq_MHz
power_a_uW = (100 * 600mW * 600mW * 500MHz) / 10^6 = 18000
power_a_mW = (100 * 600mW * 600mW * 500MHz) / 10^9 = 18
power_b_uW = (100 * 605mW * 605mW * 600MHz) / 10^6 = 21961
power_b_mW = (100 * 605mW * 605mW * 600MHz) / 10^9 = 21
max_freq = 2000MHz
cost_a_mW = 18 * 2000MHz/500MHz = 72
cost_a_uW = 18000 * 2000MHz/500MHz = 72000
cost_b_mW = 21 * 2000MHz/600MHz = 70 // <- artificially better
cost_b_uW = 21961 * 2000MHz/600MHz = 73203
The 'cost_b_mW' (which is based on old milli-Watts) is misleadingly
better that the 'cost_b_uW' (this patch uses micro-Watts) and such
would have impact on the 'inefficient OPPs' information in the Cpufreq
framework. This patch set removes the rounding issue.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
commit 65c7cdedeb ("genirq: Provide new interfaces for affinity hints")
deprecates irq_set_affinity_hint(). Use the new
irq_set_affinity_and_hint() instead.
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
If LMH (Limits Management Hardware) is available, when a policy is
disabled by unplugging the last online CPU of policy->cpus, the LMH
irq is left enabled.
When the policy is re-enabled with any of the CPU in policy->cpus
being plugged in, qcom_cpufreq_ready() re-enables the irq. This
triggers the following warning:
[ 379.160106] Unbalanced enable for IRQ 154
[ 379.160120] WARNING: CPU: 7 PID: 48 at kernel/irq/manage.c:774 __enable_irq+0x84/0xc0
Thus disable the irq.
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
If LMH (Limits Management Hardware) is available, when a policy is
disabled by unplugging the last online CPU of policy->cpus,
qcom_cpufreq_hw_cpu_offline() sets cancel_throttle=true.
cancel_throttle is not reset when the policy is re-enabled with any
of the CPU in policy->cpus being plugged in. So reset it.
This patch also adds an early exit check.
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
HZ macros has been centralized in units.h since [1]. Use it to avoid
duplicated definition.
[1] commit e2c77032fc ("units: add the HZ macros")
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
If regulator_get_voltage() fails, it should return the error code in
mtk_cpu_dvfs_info_init().
Fixes: 0daa47325b ("cpufreq: mediatek: Link CCI device to CPU")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
If the regulator_get_optional() call for the SRAM regulator returns
a probe deferral, we must bail out and retry probing later: failing
to do this will produce unstabilities on platforms requiring the
handling for this regulator.
Fixes: ffa7bdf7f3 ("cpufreq: mediatek: Make sram regulator optional")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Now that we have a central API to handle all OPP table configurations,
migrate the set-prop-name family of helpers to use the new
infrastructure.
The return type and parameter to the APIs change a bit due to this,
update the current users as well in the same commit in order to avoid
breaking builds.
Acked-by: Samuel Holland <samuel@sholland.org> # sun50i
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Now that we have a central API to handle all OPP table configurations,
migrate the set-supported-hw family of helpers to use the new
infrastructure.
The return type and parameter to the APIs change a bit due to this,
update the current users as well in the same commit in order to avoid
breaking builds.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Now that we have a central API to handle all OPP table configurations,
migrate the set-regulators family of helpers to use the new
infrastructure.
The return type and parameter to the APIs change a bit due to this,
update the current users as well in the same commit in order to avoid
breaking builds.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The OPP core now provides a unified API for setting all configuration
types, i.e. dev_pm_opp_set_config().
Lets start using it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The OPP core now provides a unified API for setting all configuration
types, i.e. dev_pm_opp_set_config().
Lets start using it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The OPP core now provides a unified API for setting all configuration
types, i.e. dev_pm_opp_set_config().
Lets start using it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Make dev_pm_opp_set_regulators() accept a NULL terminated list of names
instead of making the callers keep the two parameters in sync, which
creates an opportunity for bugs to get in.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Steven Price <steven.price@arm.com> # panfrost
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Recent Zhaoxin/Centaur CPUs support X86_FEATURE_IDA and the turbo boost
can be dynamically enabled or disabled through MSR 0x1a0[38] in the same
way as Intel. So add turbo boost control support for these CPUs too.
Signed-off-by: Tony W Wang-oc <TonyWWang-oc@zhaoxin.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This SoC shall use the mediatek-cpufreq driver, or the system will
crash upon any clock scaling request: add it to the cpufreq-dt-platdev
blocklist.
Fixes: 39b360102f ("cpufreq: mediatek: Add support for MT8186")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
In pmac_cpufreq_init_MacRISC3(), we need to add corresponding
of_node_put() for the three node pointers whose refcount have
been incremented by of_find_node_by_name().
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Offlining cpu6 and cpu7 and then onlining cpu6 hangs on
sc7180-trogdor-lazor because the throttle interrupt doesn't exist.
Similarly, things go sideways when suspend/resume runs. That's because
the qcom_cpufreq_hw_cpu_online() and qcom_cpufreq_hw_lmh_exit()
functions are calling genirq APIs with an interrupt value of '-6', i.e.
-ENXIO, and that isn't good.
Check the value of the throttle interrupt like we already do in other
functions in this file and bail out early from lmh code to fix the hang.
Reported-by: Rob Clark <robdclark@chromium.org>
Cc: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: a1eb080a04 ("cpufreq: qcom-hw: provide online/offline operations")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
In qoriq_cpufreq_probe(), of_find_matching_node() will return a
node pointer with refcount incremented. We should use of_node_put()
when it is not used anymore.
Fixes: 157f527639 ("cpufreq: qoriq: convert to a platform driver")
[ Viresh: Fixed Author's name in commit log ]
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
When system resumes from S3, the CPPC enable register will be
cleared and reset to 0.
So enable the CPPC interface by writing 1 to this register on
system resume and disable it during system suspend.
Signed-off-by: Jinzhou Su <Jinzhou.Su@amd.com>
Signed-off-by: Jinzhou Su <Jinzhou.Su@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
[ rjw: Subject and changelog edits ]
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This change was introduced long back by commit 4f750c9308 ("cpufreq:
Synchronize the cpufreq store_*() routines with CPU hotplug").
Since then, both cpufreq and hotplug core have been reworked and have
much better locking in place. The race mentioned in commit 4f750c9308
isn't possible anymore.
Drop the unnecessary locking.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Instead of specially adding a space for each CPU, except the first one,
lets add space for each of them and remove it at the end.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license version 2 as
published by the free software foundation this program is distributed
as is without any warranty of any kind whether express or implied
without even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on the normalized pattern:
this file is licensed under the terms of the gnu general public
license version 2 this program is licensed as is without any warranty
of any kind whether express or implied
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went through
several rebases before the merge window as bugs were found, so they
remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files.
-----BEGIN PGP SIGNATURE-----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=cnSb
-----END PGP SIGNATURE-----
Merge tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull more ARM multiplatform updates from Arnd Bergmann:
"The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went
through several rebases before the merge window as bugs were found, so
they remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files"
* tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: pxa/mmp: remove traces of plat-pxa
ARM: pxa: convert to multiplatform
ARM: pxa/sa1100: move I/O space to PCI_IOBASE
ARM: pxa: remove support for MTD_XIP
ARM: pxa: move mach/*.h to mach-pxa/
ARM: PXA: fix multi-cpu build of xsc3
ARM: pxa: move plat-pxa to drivers/soc/
ARM: mmp: rename pxa_register_device
ARM: mmp: remove tavorevb board support
ARM: pxa: remove unused mach/bitfield.h
ARM: pxa: move clk register definitions to driver
ARM: pxa: move smemc register access from clk to platform
cpufreq: pxa3: move clk register access to clk driver
ARM: pxa: remove get_clk_frequency_khz()
ARM: pxa: pcmcia: move smemc configuration back to arch
ASoC: pxa: i2s: use normal MMIO accessors
ASoC: pxa: ac97: use normal MMIO accessors
ASoC: pxa: use pdev resource for FIFO regs
Input: wm97xx - get rid of irq_enable method in wm97xx_mach_ops
Input: wm97xx - switch to using threaded IRQ
...
Building the cppc_cpufreq driver with for arm64 with
CONFIG_ENERGY_MODEL=n triggers the following warnings:
drivers/cpufreq/cppc_cpufreq.c:550:12: error: ‘cppc_get_cpu_cost’ defined but not used
[-Werror=unused-function]
550 | static int cppc_get_cpu_cost(struct device *cpu_dev, unsigned long KHz,
| ^~~~~~~~~~~~~~~~~
drivers/cpufreq/cppc_cpufreq.c:481:12: error: ‘cppc_get_cpu_power’ defined but not used
[-Werror=unused-function]
481 | static int cppc_get_cpu_power(struct device *cpu_dev,
| ^~~~~~~~~~~~~~~~~~
Move the Energy Model related functions into specific guards.
This allows to fix the warning and prevent doing extra work
when the Energy Model is not present.
Fixes: 740fcdc2c2 ("cpufreq: CPPC: Register EM based on efficiency class information")
Reported-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Tested-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If CONFIG_ACPI_CPPC_CPUFREQ_FIE is not set, building fails:
drivers/cpufreq/cppc_cpufreq.c: In function ‘populate_efficiency_class’:
drivers/cpufreq/cppc_cpufreq.c:584:2: error: ‘cppc_cpufreq_driver’ undeclared (first use in this function); did you mean ‘cpufreq_driver’?
cppc_cpufreq_driver.register_em = cppc_cpufreq_register_em;
^~~~~~~~~~~~~~~~~~~
cpufreq_driver
Make declare of cppc_cpufreq_driver out of CONFIG_ACPI_CPPC_CPUFREQ_FIE
to fix this.
Fixes: 740fcdc2c2 ("cpufreq: CPPC: Register EM based on efficiency class information")
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Tegra234 cpufreq support (Sumit Gupta).
- Mediatek cleanups and enhancements (Wan Jiabing, Rex-BC Chen, and
Jia-Wei Chang).
-----BEGIN PGP SIGNATURE-----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=DJhA
-----END PGP SIGNATURE-----
Merge tag 'cpufreq-arm-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Pull ARM cpufreq updates for 5.19-rc1 from Viresh Kumar:
- Tegra234 cpufreq support (Sumit Gupta).
- Mediatek cleanups and enhancements (Wan Jiabing, Rex-BC Chen, and
Jia-Wei Chang).
* tag 'cpufreq-arm-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm: (21 commits)
cpufreq: mediatek: Add support for MT8186
cpufreq: mediatek: Link CCI device to CPU
dt-bindings: cpufreq: mediatek: Add MediaTek CCI property
cpufreq: mediatek: Fix potential deadlock problem in mtk_cpufreq_set_target
cpufreq: mediatek: Add opp notification support
cpufreq: mediatek: Refine mtk_cpufreq_voltage_tracking()
cpufreq: mediatek: Move voltage limits to platform data
cpufreq: mediatek: Unregister platform device on exit
cpufreq: mediatek: Fix NULL pointer dereference in mediatek-cpufreq
cpufreq: mediatek: Make sram regulator optional
cpufreq: mediatek: Record previous target vproc value
cpufreq: mediatek: Replace old_* with pre_*
cpufreq: mediatek: Use device print to show logs
cpufreq: mediatek: Enable clocks and regulators
cpufreq: mediatek: Remove unused headers
cpufreq: mediatek: Cleanup variables and error handling in mtk_cpu_dvfs_info_init()
cpufreq: mediatek: Use module_init and add module_exit
arm64: tegra: add node for tegra234 cpufreq
cpufreq: tegra194: Add support for Tegra234
cpufreq: tegra194: add soc data to support multiple soc
...
The communication mean of the _CPC desired performance can be
PCC, System Memory, System IO, or Functional Fixed Hardware (FFH).
PCC, SystemMemory and SystemIo address spaces are available from any
CPU. Thus, dvfs_possible_from_any_cpu should be enabled in such case.
For FFH, let the FFH implementation do smp_call_function_*() calls.
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The communication mean of the _CPC desired performance can be
PCC, System Memory, System IO, or Functional Fixed Hardware.
commit b7898fda5b ("cpufreq: Support for fast frequency switching")
fast_switching is 'for switching CPU frequencies from interrupt
context'.
Writes to SystemMemory and SystemIo are fast and suitable this.
This is not the case for PCC and might not be the case for FFH.
Enable fast_switching for the cppc_cpufreq driver in above cases.
Add cppc_allow_fast_switch() to check the desired performance
register address space and set fast_switching accordingly.
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_offline() calls offline() and exit() under the policy rwsem
But they are called outside the rwsem in cpufreq_online().
Make cpufreq_online() call offline() and exit() as well as online() and
init() under the policy rwsem to achieve a clear lock relationship.
All of the init() and online() implementations in the tree only
initialize the policy object without attempting to acquire the policy
rwsem and they won't call cpufreq APIs attempting to acquire it.
Signed-off-by: Schspa Shi <schspa@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If policy initialization fails after the sysfs files are created,
there is a possibility to end up running show()/store() callbacks
for half-initialized policies, which may have unpredictable
outcomes.
Abort show()/store() in such a case by making sure the policy is active.
Also dectivate the policy on such failures.
Signed-off-by: Schspa Shi <schspa@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, cpufreq_remove_dev() invokes the ->exit() driver callback
without holding the policy rwsem which is inconsistent with what
happens if ->exit() is invoked directly from cpufreq_offline().
It also manipulates the real_cpus mask and removes the CPU device
symlink without holding the policy rwsem, but cpufreq_offline() holds
the rwsem around the modifications thereof.
For consistency, modify cpufreq_remove_dev() to hold the policy rwsem
until the ->exit() callback has been called (or it has been determined
that it is not necessary to call it).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Lukasz Luba