When beacons get stuck in AP mode, the most likely cause is interference.
Such interference can often go on for a while, and too many consecutive
beacon misses can lead to connected clients getting dropped.
Since connected clients might not be subjected to the same interference
if that happens to be very local, the AP should try to deal with it as
good as it can. One way to do this is to trigger an NF calibration with
automatic baseband update right after the beacon miss. In my tests with
very strong interference, this allowed the AP to continue transmitting
beacons after only 2-3 misses, which allows a normal client to stay
connected.
With some of the newer - really sensitive - chips, the maximum noise
floor limit is very low, which can be problematic during very strong
interference. To avoid an endless loop of stuck beacons -> nfcal ->
periodic calibration -> stuck beacons, the beacon miss event also sets
a flag, which allows the calibration code to bypass the chip specific
maximum NF value. This flag is automatically cleared, as soon as the
first NF median goes back below the limits for all chains.
In my tests, this allowed an ath9k AP to survive very strong interference
(measured NF: -68, or sometimes even higher) without losing connectivity
to its clients. Even under these conditions, I was able to transmit
several mbits/s through the interface.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stuck beacons are a useful indicator for debugging various PHY
issues such as calibration. Putting them on the same debug level
as the other beacon stuff makes it hard to spot them in huge amounts
of spam.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helps us debug channel changes better.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Atheros PCIe wireless cards handled by ath5k do require L0s disabled.
For distributions shipping with CONFIG_PCIEASPM (this will be enabled
by default in the future in 2.6.36) this will also mean both L1 and L0s
will be disabled when a pre 1.1 PCIe device is detected. We do know L1
works correctly even for all ath5k pre 1.1 PCIe devices though but cannot
currently undue the effect of a blacklist, for details you can read
pcie_aspm_sanity_check() and see how it adjusts the device link
capability.
It may be possible in the future to implement some PCI API to allow
drivers to override blacklists for pre 1.1 PCIe but for now it is
best to accept that both L0s and L1 will be disabled completely for
distributions shipping with CONFIG_PCIEASPM rather than having this
issue present. Motivation for adding this new API will be to help
with power consumption for some of these devices.
Example of issues you'd see:
- On the Acer Aspire One (AOA150, Atheros Communications Inc. AR5001
Wireless Network Adapter [168c:001c] (rev 01)) doesn't work well
with ASPM enabled, the card will eventually stall on heavy traffic
with often 'unsupported jumbo' warnings appearing. Disabling
ASPM L0s in ath5k fixes these problems.
- On the same card you would see a storm of RXORN interrupts
even though medium is idle.
Credit for root causing and fixing the bug goes to Jussi Kivilinna.
Cc: David Quan <David.Quan@atheros.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch handles the firmware loading properly
for device ID 7015.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some APs advertise that they may be HT40 capable in the capabilites
but the current operating channel configuration may be only HT20.
This causes disconnection as ath9k_htc sets WLAN_RC_40_FLAG despite
the AP operating in HT20 mode.
Hence set this flag only if the current channel configuration
is HT40 enabled.
Cc: stable@kernel.org
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_rx_skb_preprocess nulls rxs and the mactime is never set again -
mactime is always 0. This causes problems in IBSS mode.
ieee80211_rx_bss_info uses mactime to decide if an IBSS merge is needed.
Without this patch the merge is triggered by each beacon received.
This can be recognized by the "beacon TSF higher than local TSF - IBSS
merge with BSSID" log message accompanying each beacon.
This problem was not completely fixed in commit
a6d2055b02 and is not a stable kernel fix.
It is solely intended for wireless-testing.
Signed-off-by: Jan Friedrich <jft@dev2day.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed a possible issue in the paused flag management of the
ath_atx_tid data structure. In particular, in a noisy environment and
under heavy load, I observed that the AGGR session establishment could
fail several times consecutively causing values of the paused flag
greater than one for this TID (ath_tx_pause_tid is called more than
once from ath_tx_aggr_start).
Considering that the session for this TID can not be established also
after the mac80211 stack calls the ieee80211_agg_tx_operational() since
the ath_tx_aggr_resume() lowers the paused flag only by one.
This patch also replaces some BUG_ON calls with WARN_ON, as even if
these unlikely conditions happen, it's not fatal enough to justify a
BUG_ON.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9003 was not relying on the CTL indexes from the EEPROM for capping the
max output power. The CTL indexes from the EEPROM provide calibrated
limits for output power for each tested and supported frequency. Without
this the device operates at a power level which only conforms to the
transmit spectrum mask as specified by IEEE Annex I.2.3.
The regulatory limit by CRDA is always used but does not provide
calibrated values for optimal performance, specially on band edges.
Using the calibrated data from the EEPROM ensures the device
operates at optimal output power while still ensuring proper
regulatory compliance. The device uses the minimum of these tree
values, the value from CRDA, the calibrated value from CTL indexex,
and the value to conform to the IEEE transmit spectrum mask.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR5008-AR9002, other forms of calibration must not be started while
the noise floor calibration is running, as this can create invalid
readings which were sometimes not even recoverable by any further
calibration attempts.
This patch also ensures that the result of noise floor measurements
are processed faster and also allows the result of the initial
calibration on reset to make it into the NF history buffer
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The noise floor history buffer is currently not kept per channel, which
can lead to problems when changing channels from a clean channel to a
noisy one. Also when switching from HT20 to HT40, the noise floor
history buffer is full of measurements, but none of them contain data
for the extension channel, which it needs quite a bit of time to recover
from.
This patch puts all the per-channel calibration data into a single data
structure, and gives the the driver control over whether that is used
per-channel or even not used for some channels.
For ath9k_htc, I decided to keep this per-channel in order to avoid
creating regressions.
For ath9k, the data is kept only for the operating channel, which saves
some space. ath9k_hw takes care of wiping old data when the operating
channel or its channel flags change.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously the software scan callback was used to indicate to the hardware,
when it was safe to calibrate. This didn't really work properly, because it
depends on a specific order of software scan callbacks vs. channel changes.
Also, software scans are not the only thing that triggers off-channel
activity, so it's better to use the newly added indication from mac80211 for
this and not use the software scan callback for anything calibration related.
This fixes at least some of the invalid noise floor readings that I've seen
in AP mode on AR9160
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Writes to the analog shift registers, which are issues by the initval
programming function, require a 100 usec delay (similar to AR9002,
but in a different register range).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When updating the PAPRD table in hardware, PAPRD itself needs to be
disabled first, otherwise the hardware can throw a data bus error,
which upsets at least some platforms.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The periodic noise floor calibration is broken on this chip family, because
it keeps triggering a software-filtered noise floor calibration, but never
reads the result before uploading the history buffer value to the hardware.
Fix this with a call to ath9k_hw_getnf(), just like on AR9002.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR9003 the initial noise floor calibration is currently triggered
at the end of the reset without allowing the hardware to update the
baseband settings. This could potentially make scans in noisy
environments a bit more unreliable, so use the same calibration
sequence that is used on AR9002.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When issuing two consecutive scans you could often end up
getting in the logs:
"ath9k: Two wiphys trying to scan at the same time"
This message is due to a race in mac80211 but addressing
that race requires some more major changes on the driver
and perhaps optimizations on mac80211 like removing the
scan complete callback alltogether. Its too late to address
this this kernel release so supress the complaint and annotate
this needs fixing for later.
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
base index is not used anymore and so remove it.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The user ratekbs of MCS15 ShortGI is incorrect and can not be lesser
than MCS15 rate. This incorrect rate may affect switching to higher
rates as the rate control algorithm always finds MCS15 is better
than MCS15 ShortGI and results in lower throughput. Fix this by
feeding the correct user ratekbs for MCS15 ShortGI rate.
This issue affects 3 stream case very badly as the 3 stream rates are
not used at all once we scale down to MCS15 from 3 stream rates.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds 3 stream rate control support for AR938X family
chipsets which supports 3 streams.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
replace valid and valid_single_stream in rate table with bit masks
and reorganize the code so adding 3x3 rate control would be easier.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The noisefloor array index always corresponds to the rx chain number it
belongs to (with an offset of 3 for the extension chain).
It's much simpler (and actually more correct) to directly use the
chainmask to calculate the bitmask for the noisefloor array, instead of
using these weird chip revision checks and hardcoded mask values.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the noisefloor array, the extension channel values start at index 3
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the hardware is configured in HT20 mode, noise floor readings for
the extension channel often return invalid values, which keep the
values in the NF history buffer at the hardware-specific maximum limit.
Fix this by discarding the extension channel values when in HT20 mode.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an aggregation session is being cleaned up, while the tx status
for some frames is being processed, the TID is flushed and its buffers
are sent out.
Unfortunately that left the pending un-acked frames unprocessed, thus
leaking buffers. Fix this by reordering the code so that those frames
are processed first, before the TID is flushed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes txq state(txq->stopped) can be marked as started but the actual
queue may not be started (in ATH_WIPHY_SCAN state, for example). Fix this.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
snprintf() returns the number of characters that would have been written
(not counting the NUL character). So we can't use it as the limiter to
simple_read_from_buffer() without capping it first at sizeof(buf).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The snprintf() function returns the number of characters that would have
been written (not counting the NUL character on the end). It could
potentially be larger than the size of the buffer.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath9k/main.c:282:26: warning: incorrect type in assignment (different base types)
drivers/net/wireless/ath/ath9k/main.c:282:26: expected restricted __le16 [usertype] duration_id
drivers/net/wireless/ath/ath9k/main.c:282:26: got int
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An A-MPDU may contain several subframes each containing its own
CRC for the data. Each subframe also has a respective CRC for the
MPDU length and 4 reserved bits (aka delimeter CRC). AR9003 will
ACK frames that have a valid data CRC but have failed to pass the
CRC for the MPDU length, if and only if the subframe is not the
last subframe in an A-MPDU and if an OFDM phy OFDM reset error has
been caught. Discarding those subframes results in packet loss under
heavy stress conditions, an example being UDP video. Since the
frames are ACK'd by hardware we need to let these frames through
and process them as valid frames.
Cc: Tushit Jain <tushit.jain@atheros.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes this sparse complaint:
CHECK drivers/net/wireless/ath/ath9k/htc_drv_main.c
drivers/net/wireless/ath/ath9k/htc_drv_main.c:441:5:
warning: symbol 'ath9k_htc_tx_aggr_oper'
was not declared. Should it be static?
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were a few places where the sc->rxlink pointer was set to NULL "just in
case". This helps nothing - quite to the contrary it is problematic since it
can create self-linked rx descriptors in the middle of the list of receive
buffers.
Here is an example how this could happen (thanks Bob!):
cpu 0: cpu 1:
ath5k_rx_stop
ath5k_tasklet_rx
sc->rxlink = NULL; /* just in case */
// following doesn't link used
// buffer to prev.
ath5k_rxbuf_setup()
In the case of ath5k_rx_stop() and ath5k_stop_locked() buffers/descriptors are
not changed so rxlink should not be changed as well.
In ath5k_intr() we seem to try to work around a hardware bug, as the comment
(which is copied 1:1 from the HAL) suggests. I don't see how this could help.
Also the HAL does not set rxlink in this case (So where does this code come
from? It has been there since the first import of ath5k). Changed to just
increment a statistics counter.
After this patch rxlink is only set to NULL before we initialize rx descriptors
and updated when the descriptors are linked together.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on a patch from Bruno Randolf, attempting useful
work while we are resetting the chip just leads to interface
lockups and bad descriptor data, and possibly DMAing to
freed buffers. Let's suspend all tasklets while
reprogramming the registers in the card to avoid such
problems.
In the future we can convert the tasklets to threaded
interrupt handlers to simplify things.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We currently trigger a reset via a tasklet when certain error
conditions are detected so that the card will (eventually)
restart. Unfortunately this makes locking complicated since
reset can also be called in process context (e.g. for channel
change). Currently nothing protects against concurrent resets,
which can be the source of corruption bugs.
Reset takes too long to spinlock the whole thing, so this
patch moves deferred resets into the mac80211 workqueue to
enable use of sc->lock mutex.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to documentation, The following chip revisions were never sold:
- AR9280 v1.0
- AR9285 v1.0
- AR9285 v1.1
- AR9287 v1.0
Removing initvals specific to these chip revisions saves around 30k in
binary size (tested on MIPS).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch 'ath9k: fix a buffer leak in A-MPDU completion' addressed the
issue of running out of buffers/descriptors in the tx path if a STA is
deleted while tx status feedback is still pending.
The remaining issue is that the skbs of the buffers are not reclaimed,
leaving a memory leak.
This patch fixes this issue by running the buffers through
ath_tx_complete_buf(), ensuring that the pending frames counter is also
updated.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
num_sec_wiphy means max secondary wifis that the driver can accomudate.
So cancelling wiphy work should be based on the presence of
secondary wifis.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove tMinCalPower from ath9k_hw_set_def_power_cal_table(), as it's
never used. Remove corresponding arguments of the functions calculating
that value.
Original patch by Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LED should be ON when the radio is put into FULL SLEEP mode during the idle
unassociated state.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR5008+ and AR9003 currently use two separate implementations of the
ath9k_hw_loadnf function. There are three main differences:
- PHY registers for AR9003 are different
- AR9003 always uses 3 chains, earlier versions are more selective
- The AR9003 variant contains a fix for NF load timeouts
This patch merges the two implementations into one, storing the
register array in the ath_hw struct. The fix for NF load timeouts is
not just relevant for AR9003, but also important for earlier hardware,
so it's better to just keep one common implementation.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Occasionally the hardware can send out tx status information with the wrong
TID. In that case, the BA status cannot be trusted and the aggregate
must be retransmitted.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the receive path gets stuck, a full hardware reset is necessary to
recover from it. If this happens during a scan, the whole scan might fail,
as each channel change bypasses the full reset sequence.
Fix this by resetting the fast channel change flag if stopping the
receive path fails.
This will reduce the number of error messages that look like this:
ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x40000020
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PDADC values were only generated for values surrounding the target
index, however not for the target index itself, leading to a minor
error in the generated curve.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR9285, the antenna switch configuration register uses more than just
16 bits. Because of an arbitrary mask applied to the EEPROM value that
stores this configuration, diversity was broken in some cases, leading
to a significant degradation in signal strength.
Fix this by changing the callback to return a 32 bit value and remove
the arbitrary mask.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ath_tx_complete_aggr() is called, it's responsible for returning
all buffers in the linked list. This was not done when the STA lookup
failed, leading to a race condition that could leak a few buffers when
a STA just disconnected.
Fix this by immediately returning all buffers to the free list in this case.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It looks like it might be possible for a TID to be paused, while still
holding some queued buffers, however ath_tx_node_cleanup currently only
iterates over active TIDs.
Fix this by always checking every allocated TID for the STA that is being
cleaned up.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Failure cases within ath9k_hif_usb_alloc_urbs are failed
to release allocated memory.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit eed8e22f01 added support for using
multicast key lookup to support per-vif/sta keys for AP and ad-hoc.
Unfortunately, it also introduced a crash in ad-hoc mode when the sta
pointer is NULL, which happens when setting up an interface with WEP
keys. This patch fixes it by falling back to the assigned key index.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_check_alive() occasionally returns false, as the hardware
is still processing data in a specific state. Fix this issue by
repeating the test a few times with longer delay inbetween attempts.
This gets rid of excessive hardware resets that appear frequently on
some AR9132 based devices, but could also happen on AR9280.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This refactors the noise floor range checks to make them generic,
and adds proper ranges for each supported chip type.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This includes the following changes/fixes:
- a bugfix for stuck beacon issues
- timing changes for improved performance
- AGC setting improvements
- fixes for high temperature issues on some chips
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This format is generated by the initval tool, available at:
git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/initvals-tool.git
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When issuing a reset, the TSF value is lost in the hardware because of
the 913x specific cold reset. As with some AR9280 cards, the TSF needs
to be preserved in software here.
Additionally, there's an issue that frequently prevents a successful
TSF write directly after the chip reset. In this case, repeating the
TSF write after the initval-writes usually works.
This patch detects failed TSF writes and recovers from them, taking
into account the delay caused by the initval writes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'bf_retries' field of the ath_buf structure was used for both
software retries (AMPDU subframes) and hardware retries (legacy
frames). This led to a wrong retry count being reported for the A-MPDU
rate control stats.
This patch changes the code to no longer use bf_retries for reporting
retry counts, but instead always using the real on-chip retry count
from the ath_tx_status.
Additionally, if the first subframe of an A-MPDU was not acked, the tx
status report is submitted along with the first acked subframe, which
may not contain the correct rates in the tx info.
This is easily corrected by saving the tx rate info before looping over
subframes, and then copying it back once the A-MPDU status report is
submitted.
In my tests this change improves throughput visibly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In commit 39d5b2c83c "ath5k: update
AR5K_PHY_RESTART_DIV_GC values to match masks" i introduced a regression on PHY
chips older than AR5K_SREV_PHY_5413, which caused signal values to be about
10dB less that before. This patch reverts the AR5K_PHY_RESTART_DIV_GC values to
the same values which were effectively used before (without the bitmask
mistake). This brings signal levels back to normal on these PHY chips.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move ath9k_ps_wakeup() down just before accessing hw registers.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is possbile that the transmission of paprd test frame
might not get completed in 100ms if tx is stuck. Freeing
this skb upon timeout in ath_paprd_calibrate() will result
in accessing already freed memory when the associated pending
buffer is drained in txq. This patch fixes this issue.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are few places where ANI is started without checking
if it is right to start. This might lead to a case where ani
timer would be left undeleted and cause improper memory acccess
during module unload. This bug is clearly exposed with
paprd support where the driver detects tx hang and does a
chip reset. During this reset ani is (re)started without checking
if it needs to be started. This would leave a timer scheduled
even after all the resources are freed and cause a panic.
This patch introduces a bit in sc_flags to indicate if ani
needs to be started in sw_scan_start() and ath_reset().
This would fix the following panic. This issue is easily seen
with ar9003 + paprd.
BUG: unable to handle kernel paging request at 0000000000003f38
[<ffffffff81075391>] ? __queue_work+0x41/0x50
[<ffffffff8106afaa>] run_timer_softirq+0x17a/0x370
[<ffffffff81088be8>] ? tick_dev_program_event+0x48/0x110
[<ffffffff81061f69>] __do_softirq+0xb9/0x1f0
[<ffffffff810ba060>] ? handle_IRQ_event+0x50/0x160
[<ffffffff8100af5c>] call_softirq+0x1c/0x30
[<ffffffff8100c9f5>] do_softirq+0x65/0xa0
[<ffffffff81061e25>] irq_exit+0x85/0x90
[<ffffffff8155e095>] do_IRQ+0x75/0xf0
[<ffffffff815570d3>] ret_from_intr+0x0/0x11
<EOI>
[<ffffffff812fd67b>] ? acpi_idle_enter_simple+0xe4/0x119
[<ffffffff812fd674>] ? acpi_idle_enter_simple+0xdd/0x119
[<ffffffff81441c87>] cpuidle_idle_call+0xa7/0x140
[<ffffffff81008da3>] cpu_idle+0xb3/0x110
[<ffffffff81550722>] start_secondary+0x1ee/0x1f5
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some vendors require the LED to be ON always irrespective of any
radio activity. Introducing a module parameter to disable blinking,
so that one can choose between always on or led blink during
activity.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without this we could start trying to work with the device without
it being fully functional yet and loose some packets upon resume.
Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The array we use will vary depending on whether or not we are
to go to lower power or not. The default values (iniPcieSerdes)
are a copy or what go into the registers through the INI files.
Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can be useful during testing of new ASPM tweaks which often
have to be done through the PCI Serializer-Deserializer (SERDES).
Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The LowPower array writes disables the PLL when ASPM is enabled.
The host driver makes quite a few calls to ath9k_hw_configpcipowersave()
and these same calls also need to ensure the PLL is off when they issue
it.
Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR_WA register should not be read when in sleep state so
add a variable we can stash its value into for when we need
to set it. Additionally the AR_WA_D3_TO_L1_DISABLE_REAL
(bit 16) needs to be removed.
Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Madhan Jaganathan <madhan.jaganathan@atheros.com>
signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds USB IDs for some more supported
devices.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only report PHY error frames for ANI on chipsets which do not have PHY error
counters in hardware.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed RX descriptor functions against the HAL sources. Some minor changes:
- check size before making changes to the descriptor
- whitespace
- add comments about 5210 timestamps. this needs to be adressed later!
- FIFO overrun error only available on 5210
- rs_phyerr should not be OR'ed
- clear the whole ath5k_rx_status structure before using, instead of
zeroing specific fields.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are some differences between 5210 and 5211 descriptors which we did not
take into account before.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update 5210 frame types to match the HAL. We have to apply the same bitshift to
the constants as we use later.
Add 5211 specific frame types.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I carefully reviewed desh.h against the HAL sources. Added comments and made
differences between 5210, 5211 and 5212 more clear by adding _521x to the
defines which are specific to that chipset. Renamed some defines. No functional
changes.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k_hw_rx_error was only used once, where we could easily just use
ath5k_hw_rx_status as well, so remove it.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just whitespace and indentation.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use direct function calls for ath5k_hw_setup_rx_desc() and
ath5k_hw_setup_mrr_tx_desc() instead of a function pointer which always pointed
to the same function in the case of ath5k_hw_setup_rx_desc() and which is
easily unified in the case of ath5k_hw_setup_mrr_tx_desc().
Also simplify the initialization function for the remaining function pointers.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Create a new function ath5k_receive_frame_ok() which checks for errors, updates
error statistics and tells us if we want to further "receive" this frame or
not. This way we can avoid a goto and have a cleaner separation between buffer
handling and other things.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move frame reception into it's own function to have a clearer separation
between buffer and descriptor handling and things that are done when we
actually receive a frame.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no reason for a special handling (return) here, just break like we do
with the checks before.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After we free skbs for receive or transmit descriptors, make sure we have no
pointers to the now invalid memory address.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the debug ouptut rx_status_0 was printed twice instead of rx_status_1. Also
make the debug message more clear.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix comment about dma sizes, brackets were missing. Replace 'insure' with
'ensure'.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename ath5k_txbuf_free() to ath5k_txbuf_free_skb() since this is what it does:
it frees the skb and not the buf. Same for ath5k_rxbuf_free().
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that ampdu_action() can sleep, remove all
the driver hacks and just issue WMI commands
to the target.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IBSS requires the cwmin and cwmax to be respected when
we reset the txqueues on AR9003 otherwise the distribution
of beacons will be balanced towards the AR9003 card first
preventing equal contention for air time for other peers
on the IBSS.
Without this IBSS will work but only the AR9003 card will be
be issuing beacons on the IBSS.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This capability check is no longer used, so it can be removed along with
the now-obsolete ath9k_hw_getcapability function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 already masks the HT sta capabilities based on hardware support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver always sets this to enabled, but this can be simplified with
a small change to ah->sta_id1_defaults instead.
This change also removes the now-obsolete ath9k_hw_setcapability function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is only used as a workaround for an issue in one specific hw revision.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
replace calls that read this capability with accesses to ath9k_hw's
regulatory data.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All of the ciphers that are tested for are always supported
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All AR9003 features are now complete so enable AR9003
support.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_setmac() only copies the mac address it is called with into
common->macaddr, yet in all call sites, the supplied mac address pointer
is already common->macaddr.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Debugfs requires a u32 for bool knobs though so we turn the
ath9k_hw knob into a u32 as well.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k tries to prevent WMM queue tx buffer starvation caused by
traffic on different queues by limiting the number of pending frames
in a tx queue (tracked in the ath_buf structure). This had a leak
issue, because the a skb can be reassigned to a different ath_buf
in the tx path, causing the pending frame counter to become inaccurate.
To fix this, track the number of frames in an array in the softc,
using the mac80211 queue mapping as index.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR5416 and all newer chipsets use a 32 bit rx timestamp, so there
is no need to keep the 15 bit timestamp extending logic around.
This patch removes ath9k_hw_extend_tsf (replaced by a call to
ath9k_hw_gettsf64), and reduces the frequency of TSF reads, which
can improve performance in some cases.
This change also has the side effect of making rx timestamps
more accurate.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_get_mac80211_qnum() expects the queue 'subtype'
(internal ID for the WMM AC) as argument when looking up
the mac80211 queue, however ath_wake_mac80211_queue provides
txq->axq_qnum instead, which contains the hardware queue
number. Fix this by keeping track of the WMM class ID in
the txq data structure.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All AR9003 devices are PCI-E only, the extra delay here
is not required and only reduces the delay for loading
the initial register values by at least 14ms.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9003 has been tested with the new ANI implementation
and so ANI can now be enabled for that family.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for ANI for AR9003. The implementation for
ANI for AR9003 is slightly different than the one used for
the older chipset families. It can technically be used for
the older families as well but this is not yet fully tested
so we only enable the new ANI for the AR5008, AR9001 and AR9002
families with a module parameter, force_new_ani.
The old ANI implementation is left intact.
Details of the new ANI implemention:
* ANI adjustment logic is now table driven so that each ANI level
setting is parameterized. This makes adjustments much more
deterministic than the old procedure based logic and allows
adjustments to be made incrementally to several parameters per
level.
* ANI register settings are now relative to INI values; so ANI
param zero level == INI value. Appropriate floor and ceiling
values are obeyed when adjustments are combined with INI values.
* ANI processing is done once per second rather that every 100ms.
The poll interval is now a set upon hardware initialization and
can be picked up by the core driver.
* OFDM error and CCK error processing are made in a round robin
fashion rather than allowing all OFDM adjustments to be made
before CCK adjustments.
* ANI adjusts MRC CCK off in the presence of high CCK errors
* When adjusting spur immunity (SI) and OFDM weak signal detection,
ANI now sets register values for the extension channel too
* When adjusting FIR step (ST), ANI now sets register for FIR step
low too
* FIR step adjustments now allow for an extra level of immunity for
extremely noisy environments
* The old Noise immunity setting (NI), which changes coarse low, size
desired, etc have been removed. Changing these settings could affect
up RIFS RX as well.
* CCK weak signal adjustment is no longer used
* ANI no longer enables phy error interrupts; in all cases phy hw
counting registers are used instead
* The phy error count (overflow) interrupts are also no longer used
for ANI adjustments. All ANI adjustments are made via the polling
routine and no adjustments are possible in the ISR context anymore
* A history settings buffer is now correctly used for each channel;
channel settings are initialized with the defaults but later
changes are restored when returning back to that channel
* When scanning, ANI is disabled settings are returned to (INI) defaults.
* OFDM phy error thresholds are now 400 & 1000 (errors/second units) for
low/high water marks, providing increased stability/hysteresis when
changing levels.
* Similarly CCK phy error thresholds are now 300 & 600 (errors/second)
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new ANI implementation will use this to skip ANI
calibration upon a scan. This cannot be ported to the
older ANI implementation unless default ANI values from
the ANI are also used upon a scan. This is essentially
what one of the things thenew ANI does.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9003 hardware family will use a slightly modified ANI
implementation which has not yet been tested on the other hardware
families. To allow for this new ANI implementation a few ANI
calls need to be abstracted away. This patch just allows for
each hardware family to declare their own ANI ops and annotates
the current ANI implementation as old.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We get an MIB interrupt when we hit certain PHY error counter
thresholds. If ANI is disabled but the MIB interrupt is enabled
we'll keep around the old MIB interrupt causes.
Since ath9k disables the MIB interrupt when ANI is disabled
this is not a fix, but more of a sanity fix in case we ever
need the MIB interrupt enabled but disabling ANI.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The clock rate was assumed to be static but it actually
changes depending on the mode of operation, correct this
to help improve the calcuation of the listenTime for ANI.
This change will help adjust ANI more accurately on different
PHY thresholds.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These will be used by the ANI code next.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow drivers to sleep, and indicate this in
the documentation. ath9k has some locking I
don't understand, so keep it safe and disable
BHs in it, all other drivers look fine with
the context change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The non-irqsafe aggregation start/stop done
callbacks are currently only used by ath9k_htc,
and can cause callbacks into the driver again.
This might lead to locking issues, which will
only get worse as we modify locking. To avoid
trouble, remove the non-irqsafe versions and
change ath9k_htc to use those instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since ath5k_hw_set_antenna_mode() always writes the default antenna register
and is called at the end of reset, there is no need to separately save and
restore the default antenna.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Collect all pieces concering the antenna switch table into one function.
Previously it was split up between ath5k_hw_reset() and
ath5k_hw_commit_eeprom_settings().
Also we need to set the antenna switch table when ath5k_hw_set_antenna_mode()
is called manually (by "iw phy0 antenna set", for example).
I'm not sure if we need to set the switchtable at the same place in
ath5k_hw_reset() as it was before - it is set later thru
ath5k_hw_set_antenna_mode() anyways - but i leave it there to avoid
problems(?).
Plus print switchtable registers in the debugfs file.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
#define AR5K_PHY_RESTART_DIV_GC 0x001c0000
is 3 bit wide.
The previous values of 0xc and 0x8 are 4bit wide and bigger than the mask.
Writing 0 and 1 to AR5K_PHY_RESTART_DIV_GC is consistent with the comments and
initvals we have in the HAL.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes 'make -j24 CONFIG_DEBUG_SECTION_MISMATCH=y' warning:
drivers/net/wireless/ath/ath9k/eeprom_4k.c: In function ‘ath9k_hw_get_4k_gain_boundaries_pdadcs.clone.1’:
drivers/net/wireless/ath/ath9k/eeprom_4k.c:311: error: ‘minPwrT4’ may be used uninitialized in this function
drivers/net/wireless/ath/ath9k/eeprom_9287.c: In function ‘ath9k_hw_get_AR9287_gain_boundaries_pdadcs’:
drivers/net/wireless/ath/ath9k/eeprom_9287.c:302: error: ‘minPwrT4’ may be used uninitialized in this function
drivers/net/wireless/ath/ath9k/eeprom_def.c: In function ‘ath9k_hw_get_def_gain_boundaries_pdadcs.clone.0’:
drivers/net/wireless/ath/ath9k/eeprom_def.c:679: error: ‘minPwrT4’ may be used uninitialized in this function
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the channel is not set yet and we configure the antennas just store the
setting. It will be activated during the next reset, when the channel is set.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The following commit added an entry in 11na and 11ng rate
table but missed to update its rate count field. This
inconsistency between the rate count and the actual number
of rates in the table will leave out the final rate entry
(mcs15 with half gi in ht40) while forming the valid
rate indices. Not having mcs15+shortGI in ht40 will have
a performance impact (on max throughput) of about 10% both
in nght40 and naht40 mode.
Author: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Date: Thu May 13 18:42:38 2010 -0700
ath9k: Enable Short GI in 20 Mhz for ar9287 and later chips
This patch enables short GI rx at all rates and tx at mcs15
for 20 Mhz channel width also.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For non-AR9271 chips, the credit size is different
and has to be configured appropriately.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR7010 is dual-band. Setup the channels and rateset
for 5GHz band.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rate information on the target has to be updated
for 2-stream devices, along with the correct chainmask.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The supported MCS rate set has to be setup properly
for 2-stream devices.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the USB device IDs for AR7010 and handle
firmware loading properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes programming the byte swap registers
for chipsets other than AR9271. This is needed for
AR7010.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not assign the FW name to driver_info but determine
it dynamically on device probe. This facilitates adding new
firmware.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 56d1de0a21, "ath5k: clean up
filter flags setting" introduced a regression in monitor mode such
that the promisc filter flag would get lost.
Although we set the promisc flag when it changed, we did not
preserve it across subsequent calls to configure_filter. This patch
restores the original functionality.
Cc: stable@kernel.org
Bisected-by: weedy2887@gmail.com
Tested-by: weedy2887@gmail.com
Tested-by: Rick Farina <sidhayn@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When building a kernel with CONFIG_PM=y but neither suspend nor
hibernate support, the compiler complains about the static functions
ath5k_pci_suspend() and ath5k_pci_resume() not being used:
drivers/net/wireless/ath/ath5k/base.c:713:12: warning: ‘ath5k_pci_suspend’ defined but not used
drivers/net/wireless/ath/ath5k/base.c:722:12: warning: ‘ath5k_pci_resume’ defined but not used
Depending on CONFIG_PM_SLEEP rather than CONFIG_PM fixes the issue.
Signed-off-by: Tobias Doerffel <tobias.doerffel@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sta_add/sta_remove are the callbacks that can sleep.
Use them instead of sta_notify.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If buffer is to be accessed by cpu after dma is over, but
between dma mapping and dma unmapping, we should use
dma_sync_single_for_cpu to sync the buffer between cpu with
device. And dma_sync_single_for_device is used to let
device gain the buffer again.
v2: Felix pointed out dma_sync_single_for_device is needed to return
buffer to device if an unsuccessful status bit check is found.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because there is a limited number of tx buffers available, once the
queue has been filled to a certain point, ath9k needs to stop accepting
new frames from mac80211. In order to prevent a full WMM queue from
stopping another queue with fewer frames, this patch limits the number
of queued frames to a quarter of the total available tx buffers, minus
some reserved frames to be used for other purposes (e.g. beacons).
Because tx buffers are reserved for frames when they're staged in
software queues as well, the actual queue depth cannot be used for
this, so this patch stores a reference to the tx queue in the ath_buf
struct and keeps track of the total number of pending frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes beacon distribution in IBSS mode
by configuring the hardware beacon queue properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MIB counters used by ANI have to be disabled
on the host because the FW doesn't do it on the target side.
Also, flush the receive buffers before initializing
RX on the target.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The monitor interface instance on the target has
to be removed before setting it to FULLSLEEP.
Handle this properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ps_idle is protected by the htc_pm_lock mutex.
Use it to protect the variable.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to cancel the PS work when disassociation
happens. The work handlers are cancelled in the stop()
callback.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable the radio only when mac80211 indicates it,
through the IEEE80211_CONF_CHANGE_IDLE flag.
Not handling this properly will result in multiple
calls to radio_disable() even though the radio is
already idle.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW has to be awake when registers are accessed.
Ensure this is so by using the PS wrappers at
appropriate places.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch revamps IDLE power save handling in the driver.
Two separate functions (radio enable/disable) are introduced,
because the semantics of radio handling is just not the same
as the start()/stop() callbacks. For example, the HW must not
be disabled, instead, the PHY has to be disabled in radio_disable().
Also, the HW has to be reset properly in radio enable/disable and
certain registers have to be programmed only once, in the
start() callback.
The radio_enable() routine doesn't need the PS wrappers since
we set the HW power mode to AWAKE anyway before calling it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Async fifo is now enabled only for versions 1.3 and above.
Enable it in the appropriate place, in the reset routine,
instead of process_ini().
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates the PCI power save handling
code, fixing ASPM hangs and handling device state D3
properly.
The WAR register is programmed with the correct
values now.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add a few comments, and move the updation of max_power_level
to a helper routine. This is also done by non-4K based chipsets,
this will be fixed in a separate patch.
* Remove two WARs which are required for old AR5416 chipsets,
and are not needed for AR9287.
* Fix indentation and make things readable.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rather than doing a series of RMWs, calculate the
value to be written to the register in question and
do a single REGWRITE. This improves bringup time.
This depends on the analog_shiftreg configuration option,
which is currently buggy. For AP mode, a delay of 100us
has to be the default. For station mode, this knob has to
be enabled on a per-case basis, though it is a little
unclear on when to enable a delay. This can be fixed later though.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Fix whitespace damage.
* Remove unused debug messages.
* Introduce a macro NUM_EEP_WORDS.
* Convert AR9287 to lowercase in function names.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces the buggy 'ath9k: Group Key fix for VAPs' change.
For AP mode group keys, use the BSSID as lookup mac address, with
the multicast keysearch bit set.
For IBSS mode, use the peer's MAC address with multicast keysearch.
For STA mode, keep using the group key slots.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a MAC address for a key table entry is flagged with the
multicast bit (0x01), indicate to the hardware that multicast
lookup instead of unicast lookup should be used. The multicast
bit itself never makes it to the actual keytable entry register,
as it is shifted out.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We dereference "wmi" on the line before and also when we initialize "ah".
This check has always been after a dereference since the first commit a
couple months ago. Looking through the code, it looks like "wmi" can't
actually be null here so I just removed the check.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rx status length should also be taken into account while
validating the length of a received frame.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Skip the rx status portion in skb->data before accessing ieee80211
frame header.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_rx_skb_preprocess() needs only ieee80211 frame header,
pass only frame headers instead of skb to that function. Also
remove ineffective frame dump in ath9k_process_rate().
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A bunch of data structures are present in the
common module, which are internal to ath9k.
Move them to ath9k.h
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch relocates RX processing code from the
common module to ath9k. This reduces the size
of the common module which is also used by ath9k_htc.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To enable it we now disable and re-enable the PHY chips
after TX IQ calibration.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we have sysfs to manually set the ANI levels, we should print errors to
the kernel log if the values are out of bounds.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calculate 'listen' time also when automatic ANI is off, since this and the
"busy" time is useful information also in manual mode.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
/sys/class/ieee80211/phy0/device/ani/ani_mode
/sys/class/ieee80211/phy0/device/ani/noise_immunity_level
/sys/class/ieee80211/phy0/device/ani/spur_level
/sys/class/ieee80211/phy0/device/ani/firstep_level
/sys/class/ieee80211/phy0/device/ani/ofdm_weak_signal_detection
/sys/class/ieee80211/phy0/device/ani/cck_weak_signal_detection
/sys/class/ieee80211/phy0/device/ani/noise_immunity_level_max
/sys/class/ieee80211/phy0/device/ani/spur_level_max
/sys/class/ieee80211/phy0/device/ani/firstep_level_max
sysfs has a lot of symlinks, so you can find the files also in other locations,
like (by PCI ID) /sys/devices/pci0000:00/0000:00:11.0/ani and others.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's our "private driver data"... It's used more often and hw is the mac80211
part. This makes more sense with the next (sysfs) patch.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old code logically did not make sense and seems to have been confused by
the fact that we could have newer EEPROMs on older hardware. In any case the
spur mitigation filter was set if the srev was >= AR5K_SREV_AR5424.
Spur info is available only from EEPROM versions bigger than 5.3 but but the
EEPOM routines will use static values for older versions, so that should be
o.k.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we have ftrace, it is not needed any more.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since NF calibration interferes with TX and RX and also has been the cause of
other problems (when it's run concurrently with ath5k_reset) we want to run it
less often - every 60 seconds for now.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As far as we know, only NF calibration interferes with RX/TX so we can
leave the queues enabled for the other calibrations.
BTW: Stopping the queues is not enough for avoiding transmissions, since there
might be packets in the queue + beacons are also sent regularly! But i leave it
like this until we have a better solution (stopping TX DMA?).
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Seperate noise floor calibration from other PHY calibration and move it to the
tasklet. This is the first step to more separation of different calibrations.
Also move out ath5k_hw_request_rfgain_probe(ah) so we have one clean function
for I/Q calibration on 5111x parts.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize calibration timers on reset, since otherwise they might be in the
future and the calibration tasklet might not be scheduled for a long time.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rx should not be disabed/disabled when hw supports auto sleeping.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add missing code to handle nullfunc frame completion in
ath_tx_edma_tasklet().
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use BSS_CHANGED_HT to handle HT parameter changes.
The rate information on the target has to be updated
to handle changes in HT configuration.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes a large chunk of code dealing
with rate management within the driver and simplifying
things by removing the hacky method of calculating
HT changes. A subsequent patch would fix this by
just using BSS_CHANGED_HT from mac80211.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update from internal systems engineering team.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changed -EINVAL to -EFAULT if copy_to_user() failed.
Changed 0 to -ENOMEM if allocations failed.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The snprintf() function returns the number of bytes that *would* have
been written (not counting the NULL terminator) and that can potentally
be more than the size of the buffer.
In this patch if there were one liners where string clearly fits into
the buffer, then I changed snprintf to sprintf(). It's confusing to use
the return value of snprintf() as a limitter without verifying that it's
smaller than size. This is what initially caught my attention here.
If we use the return value of sprintf() instead future code auditors will
assume we've verified that it fits already.
Also I did find some places where it made sense to use the return value
after we've verified that it is smaller than the buffer size.
Finally the read_file_rcstat() function added an explicit NULL terminator
before calling snprintf(). That's unnecessary because snprintf() will
add the null terminator automatically.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For edma, we should use DMA_BIDIRECTIONAL, or else use
DMA_FROM_DEVICE.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the maximum supported by the firmware.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to determine the HW queue
for each packet that is transmitted. The endpoint
can be chosen directly based on the queue type
that mac80211 sends down.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch initializes the beacon and CAB HW queues
when the driver is loaded.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables short GI rx at all rates and tx at mcs15
for 20 Mhz channel width also.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables the baseband watchdog events for the AR9003
family on ath9k. Upon an a baseband watchdog interrupt we reset
the hardware, this should address corner case conditions where
normal operation can stall. Enable ATH_DBG_RESET to be able
to review details of the bb watchdog interrupt once it happens.
If you're curious how often this happens just grep the debugfs
interrupt file.
Cc: Sam Ng <sam.ng@atheros.com>
Cc: Paul Shaw <paul.shaw@atheros.com>
Cc: Don Breslin <don.breslin@atheros.com>
Cc: Cliff Holden <cliff.holden@atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The baseband watchdog will monitor blocks of the baseband
through timers and will issue an interrupt when things are
detected to be stalled. It is only available on the AR9003
family.
Cc: Sam Ng <sam.ng@atheros.com>
Cc: Paul Shaw <paul.shaw@atheros.com>
Cc: Don Breslin <don.breslin@atheros.com>
Cc: Cliff Holden <cliff.holden@atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can wake all queues after a chip reset since everything should be set up and
we are ready to transmit. If we don't do that we might end up starting up with
stopped queues, not beeing able to transmit. (This started to happen after
"ath5k: clean up queue manipulation" but since periodic calibration also
stopped and started the queues this effect was hidden most of the time).
This way we can also get rid of the superfluous ath5k_reset_wake() function.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This bug was introduced by the following commit
Author: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Date: Thu Apr 15 17:38:46 2010 -0400
ath9k: Remove ATH9K_TX_SW_ABORTED and introduce a bool for this purpose
Wrong buffer is checked for bf_tx_aborted field in ath_tx_num_badfrms(),
this may result in a rate scaling with wrong feedback (number
of unacked frames in this case). It is the last one in the chain
of buffers for an aggregate frame that should be checked.
Also it misses the initialization of this field in the buffer,
this may lead to a situation where we stop the sw retransmission
of failed subframes associated to this buffer.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_print in xmit.c should say "Reseting hardware"
instead of Resetting HAL!(since HAL is being fazed out).
dmesg shows:
[ 8660.899624] ath: Failed to stop TX DMA in 100 msec after killing last frame
[ 8660.899676] ath: Unable to stop TxDMA. Reset HAL!
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With VEOL, Beacon transmission in ad-hoc does not currently work.
I believe for larger ad-hoc networks, VEOL is too unreliable, as
it can get beacon transmissions stuck during synchronization.
Use SWBA based beacon trasmission similar to AP mode instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes IBSS beacon transmissions without VEOL enabled
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functionality to keep the device awake until it is done with
the rx of any mcast/bcast frames which are pending on AP should
also be added to the hardwares which support auto sleep feature.
This patch fixes frequent failures in ARP resolution when it is
initiated by the other end. Currently auto sleep is enabled only
for ar9003 in ath9k.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is obviously a small picky thing. The original error handling code
doesn't free the most recent allocations which haven't been added to the
hif_dev->tx.tx_buf list yet.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After c11d8f89d3b7: "ath9k_htc: Simplify TX URB management" we no longer
assume that tx_buf is a non-null pointer.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 03ceedea97.
This patch was reported to cause a regression in which connectivity is
lost and cannot be reestablished after a suspend/resume cycle.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should use the same buffer size we set up for DMA also in the hardware
descriptor. Previously we used common->rx_bufsize for setting up the DMA
mapping, but used skb_tailroom(skb) for the size we tell to the hardware in the
descriptor itself. The problem is that skb_tailroom(skb) can give us a larger
value than the size we set up for DMA before. This allows the hardware to write
into memory locations not set up for DMA. In practice this should rarely happen
because all packets should be smaller than the maximum 802.11 packet size.
On the tested platform rx_bufsize is 2528, and we allocated an skb of 2559
bytes length (including padding for cache alignment) but sbk_tailroom() was
2592. Just consistently use rx_bufsize for all RX DMA memory sizes.
Also use the return value of the descriptor setup function.
Cc: stable@kernel.org
Signed-off-by: Bruno Randolf <br1@einfach.org>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We tried to squeeze as much AR9003 support into this kernel
release cycle but there are a few features which are still
being tested and developed. Some of these features are critical
to the stable operation of AR9003 so for now disable AR9003 support
all together. This will get re-enabled once all necessary features
are in place but very likely will not happen for 2.6.35.
Reviewed-by: Don Breslin <don.breslin@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For more clearance what the functions actually do,
usb_buffer_alloc() is renamed to usb_alloc_coherent()
usb_buffer_free() is renamed to usb_free_coherent()
They should only be used in code which really needs DMA coherency.
All call sites have been changed accordingly, except for staging
drivers.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pedro Ribeiro <pedrib@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
switch and while statements don't need semicolons at end of statement
[ Fixup minor conflicts with recent wimax merge... -DaveM ]
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
It also does not remove null void functions with return.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
with some cleanups by hand.
Compile tested x86 allmodconfig only.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* add support for the Qwest/Actiontec 802AIN Wireless N USB Network Adapter.
lsusb identifies the device as: "ID 1668:1200 Actiontec Electronics, Inc. [hex]"
usb_modeswitch package and appropriate rules are required to switch
the device from "ID 0ace:20ff ZyDas"
Changes-licensed-under: GPL
Signed-off-by: Steve Tanner <steve.tanner@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the double swapping of the descriptor data structure, instead
keep it little-endian (native format of the eeprom data), and byteswap
on access.
This allows sparse to verify endian access to the eeprom struct.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ENDPOINT_MAX instead of HST_ENDPOINT_MAX.
This fixes a stack corruption issue.
This is based on a patch sent by Dan Carpenter <error27@gmail.com>.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ready message from the target could be processed
before the host HW init has completed. In this case,
htc_process_target_rdy() would assume the target has timed
out, when it hasn't. Fix this by checking if the target
has sent the ready message properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HTC state has to be setup before initializing
the target because the ready message could possibly
come before the control endpoints in HTC have been
identified.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The URBs have to be allocated before uploading
the firmware to the target. This is needed to process
the target ready message properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since ->sta_notify() can sleep, protect
the callback with a mutex.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't send them for further processing.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These changes include:
* For PAPRD, the TXRF3.capdiv5G, TXRF3.rdiv5G and TXRF3.rdiv2G
are set to 0x0, the TXRF6.capdiv2G is set to 0x2 for all
three chains.
* The d2cas5G/d3cas5G/d4cas5G was updated to 4/4/4 in lowest_ob_db
Tx gain table.
* To improve DPPM, three parameters were updated (Released from Madhan):
1. RANGE_OSDAC is set to 0x1 for 2G, 0x0 for 5G
2. offsetC1 is set to 0xc
3. inv_clk320_adc is set to 0x1
* To reduce PHY error(from spur), cycpwr_thr1 and cycpwr_thr1_ext
are increased to 0x8 at 2G.
* The 2G Rx gain tables are updated with mixer gain setting 3,1,0.
The new checksums yield:
initvals -f ar9003
0x00000000c2bfa7d5 ar9300_2p0_radio_postamble
0x00000000ada2b114 ar9300Modes_lowest_ob_db_tx_gain_table_2p0
0x00000000e0bc2c84 ar9300Modes_fast_clock_2p0
0x00000000056eaf74 ar9300_2p0_radio_core
0x0000000000000000 ar9300Common_rx_gain_table_merlin_2p0
0x0000000078658fb5 ar9300_2p0_mac_postamble
0x0000000023235333 ar9300_2p0_soc_postamble
0x0000000054d41904 ar9200_merlin_2p0_radio_core
0x00000000748572cf ar9300_2p0_baseband_postamble
0x000000009aa5a0a4 ar9300_2p0_baseband_core
0x000000003df9a326 ar9300Modes_high_power_tx_gain_table_2p0
0x000000001cfba124 ar9300Modes_high_ob_db_tx_gain_table_2p0
0x0000000011302700 ar9300Common_rx_gain_table_2p0
0x00000000e3eab114 ar9300Modes_low_ob_db_tx_gain_table_2p0
0x00000000c9d66d40 ar9300_2p0_mac_core
0x000000001e1d0800 ar9300Common_wo_xlna_rx_gain_table_2p0
0x00000000a0c54980 ar9300_2p0_soc_preamble
0x00000000292e2544 ar9300PciePhy_pll_on_clkreq_disable_L1_2p0
0x000000002d3e2544 ar9300PciePhy_clkreq_enable_L1_2p0
0x00000000293e2544 ar9300PciePhy_clkreq_disable_L1_2p0
Cc: Don Breslin <don.breslin@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jumbo frames are not supported, and if they are seen it is likely
a bogus frame so just silently discard them instead of warning on
them all time. Also, instead of dropping them immediately though
move the check *after* we check for all sort of frame errors. This
should enable us to discard these frames if the hardware picks
other bogus items first. Lets see if we still get those jumbo
counters increasing still with this.
Jumbo frames would happen if we tell hardware we can support
a small 802.11 chunks of DMA'd frame, hardware would split RX'd
frames into parts and we'd have to reconstruct them in software.
This is done with USB due to the bulk size but with ath5k we
already provide a good limit to hardware and this should not be
happening.
This is reported quite often and if it fills the logs then this
needs to be addressed and to avoid spurious reports.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau