We use devm, so irq number is only needed during probe.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Very basic operations, just called once, can also go to the caller.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_gpio_request() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Violeta Menendez <violeta.menendez@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
Tested-by: Violeta Menendez <violeta.menendez@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-eg20t driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32. Add COMPILE_TEST as an alternative, so that the
driver can still be build-tested elsewhere.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Newer SoCs have so fast input clocks that the ICCL/H registers only
count every second clock to have a meaningful 9-bit range. The driver
was already prepared for that happening, but didn't use it so far.
Add the proper DT configuration for SoCs that need it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Due to misconfiguration, it can happen that the calculated timing
parameters are out of range. Bail out if that happens. We can also
simplify some logic later because of the verified value. Also, make the
printouts of the values more precise by adding the hex-prefixes.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
sh_mobile_i2c_init() could detect wrong settings, but didn't bail out,
so it would continue unconfigured. Fix this.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Following the KISS principle, remove unneeded stuff.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is what devm was made for. No rollback mechanism needed, remove the
hook parameter from the irq setup function and simplify it. While we are
here change some variables to proper types.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Convert the easy parts to devm. irqs will be converted in a seperate
patch to keep diffs readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use standard i2c error codes for i2c failures. Also, don't print
something on timeout since it happens regularly with i2c. Simplify some,
logic, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
No functional change, binaries are identical.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
HSI2C module on Exynos5260 differs from current modules in
following ways:
1. HSI2C on Exynos5260 has fifo_depth of 16bytes
2. Module needs to be reset as a part of init sequence.
Hence, Following changes are involved.
1. Add a new compatible string and Updates the Documentation dt bindings.
2. Introduce a variant struct to support the changes in H/W
3. Reset the module during init. Thus, bringing the module back
to default state irrespective of what firmware did with it.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixed most checkpatch.pl issues
Signed-off-by: Richard Leitner <me@g0hl1n.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For !CONFIG_PM_RUNTIME, the device were never put back into active
state while resuming.
For CONFIG_PM_RUNTIME, we blindly trusted the device to be inactive
while we were about to handle it at suspend late, which is just too
optimistic.
Even if the driver uses pm_runtime_put_sync() after each tranfer to
return it's runtime PM resources, there are no guarantees this will
actually mean the device will inactivated. The reason is that the PM
core will prevent runtime suspend during system suspend, and thus when
a transfer occurs during the early phases of system suspend the device
will be kept active after the transfer.
To handle both issues above, use pm_runtime_force_suspend|resume() from
the system suspend|resume callbacks.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The smbus block read is not currently supported for imx i2c devices.
This patchset adds the support to imx i2c bus so that blocks of data
can be read using SMbus block reads.(using i2c_smbus_read_block_data()
function from the i2c_core.c.). Tested with 3.10.9 kernel.
Reviewed-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Kaushal Butala <kaushalkernelmailinglist@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Move to the other
pattern for consistency across all Allwinner Socs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wsa: dropped binding OK as per
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-February/229438.html]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This hardware does not support zero length transfers. Instead, the
driver does one (random) byte transfers currently with undefined results
for the slaves. We now bail out.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
This patch corrects the error check on the call to pm_runtime_get_sync.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Reviewed-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Don't unmark the device as suspended until after it's been re-setup.
The main race would be w.r.t. an i2c driver that gets resumed at the same
time (asyncronously), that is allowed to do a transfer since suspended
is set to 0 before reinit, but really should have seen the -EIO return
instead.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
There have been "i2c_designware 80860F41:00: controller timed out" errors
on a number of Baytrail platforms. The issue is caused by incorrect value in
Interrupt Mask Register (DW_IC_INTR_MASK) when i2c core is being enabled.
This causes call to __i2c_dw_enable() to immediately start the transfer which
leads to timeout. There are 3 failure modes observed:
1. Failure in S0 to S3 resume path
The default value after reset for DW_IC_INTR_MASK is 0x8ff. When we start
the first transaction after resuming from system sleep, TX_EMPTY interrupt
is already unmasked because of the hardware default.
2. Failure in normal operational path
This failure happens rarely and is hard to reproduce. Debug trace showed that
DW_IC_INTR_MASK had value of 0x254 when failure occurred, which meant
TX_EMPTY was unmasked.
3. Failure in S3 to S0 suspend path
This failure also happens rarely and is hard to reproduce. Adding debug trace
that read DW_IC_INTR_MASK made this failure not reproducible. But from ISR
call trace we could conclude TX_EMPTY was unmasked when problem occurred.
The patch masks all interrupts before the controller is enabled to resolve the
faulty DW_IC_INTR_MASK conditions.
Signed-off-by: Wenkai Du <wenkai.du@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: improved the comment and removed typo in commit msg]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Pull i2c updates from Wolfram Sang:
"Here is the pull request from the i2c subsystem. It got a little
delayed because I needed to wait for a dependency to be included
(commit b424080a9e08: "reset: Add optional resets and stubs"). Plus,
I had some email problems. All done now, the highlights are:
- drivers can now deprecate their use of i2c classes. That shouldn't
be used on embedded platforms anyhow and was often blindly
copy&pasted. This mechanism gives users time to switch away and
ultimately boot faster once the use of classes for those drivers is
gone for good.
- new drivers for QUP, Cadence, efm32
- tracepoint support for I2C and SMBus
- bigger cleanups for the mv64xxx, nomadik, and designware drivers
And the usual bugfixes, cleanups, feature additions. Most stuff has
been in linux-next for a while. Just some hot fixes and new drivers
were added a bit more recently."
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (63 commits)
i2c: cadence: fix Kconfig dependency
i2c: Add driver for Cadence I2C controller
i2c: cadence: Document device tree bindings
Documentation: i2c: improve section about flags mangling the protocol
i2c: qup: use proper type fro clk_freq
i2c: qup: off by ones in qup_i2c_probe()
i2c: efm32: fix binding doc
MAINTAINERS: update I2C web resources
i2c: qup: New bus driver for the Qualcomm QUP I2C controller
i2c: qup: Add device tree bindings information
i2c: i2c-xiic: deprecate class based instantiation
i2c: i2c-sirf: deprecate class based instantiation
i2c: i2c-mv64xxx: deprecate class based instantiation
i2c: i2c-designware-platdrv: deprecate class based instantiation
i2c: i2c-davinci: deprecate class based instantiation
i2c: i2c-bcm2835: deprecate class based instantiation
i2c: mv64xxx: Fix reset controller handling
i2c: omap: fix usage of IS_ERR_VALUE with pm_runtime_get_sync
i2c: efm32: new bus driver
i2c: exynos5: remove unnecessary cast of void pointer
...
If the renamed symbol is defined lib/iomap.c implements ioport_map and
ioport_unmap and currently (nearly) all platforms define the port
accessor functions outb/inb and friend unconditionally. So
HAS_IOPORT_MAP is the better name for this.
Consequently NO_IOPORT is renamed to NO_IOPORT_MAP.
The motivation for this change is to reintroduce a symbol HAS_IOPORT
that signals if outb/int et al are available. I will address that at
least one merge window later though to keep surprises to a minimum and
catch new introductions of (HAS|NO)_IOPORT.
The changes in this commit were done using:
$ git grep -l -E '(NO|HAS)_IOPORT' | xargs perl -p -i -e 's/\b((?:CONFIG_)?(?:NO|HAS)_IOPORT)\b/$1_MAP/'
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During development, the driver first really needed to depend on
COMMON_CLK only. Later, it was switched to writel_relaxed, but it was
forgotten to update the dependencies, so build errors occured:
config: make ARCH=i386 allyesconfig
All error/warnings:
drivers/i2c/busses/i2c-cadence.c: In function 'cdns_i2c_clear_bus_hold':
>> drivers/i2c/busses/i2c-cadence.c:168:3: error: implicit declaration
>> of function 'writel_relaxed' [-Werror=implicit-function-declaration]
Use a very safe dependency for now.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add a driver for the Cadence I2C controller. This controller is for
example found in Xilinx Zynq.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It is used with of_property_read_u32(), so it should be u32.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Fixes: 10c5a84259 ('i2c: qup: New bus driver for the Qualcomm QUP I2C controller')
These should ">= ARRAY_SIZE()" instead of "> ARRAY_SIZE()".
Fixes: 10c5a84259 ('i2c: qup: New bus driver for the Qualcomm QUP I2C controller')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This bus driver supports the QUP i2c hardware controller in the Qualcomm SOCs.
The Qualcomm Universal Peripheral Engine (QUP) is a general purpose data path
engine with input/output FIFOs and an embedded i2c mini-core. The driver
supports FIFO mode (for low bandwidth applications) and block mode (interrupt
generated for each block-size data transfer).
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Tested-by: Philip Elcan <pelcan@codeaurora.org>
[wsa: removed needless IS_ERR_VALUE]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: Barry Song <baohua@kernel.org>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The reset framework recently gained optional stubs when CONFIG_RESET_CONTROLLER
is not selected. It also introduced a function reset_get_optional, that is also
dummy-defined whenever the framework isn't enabled, for drivers that needs an
optional reset controller.
Switch to this function, since the mv64xxx driver is in this case. This also
fixes a compilation breakage whenever the reset framework wasn't selected:
drivers/i2c/busses/i2c-mv64xxx.c:771:2: error: implicit declaration of function 'devm_reset_control_get'
While we're at it, remove the redundant test on dev.of_node surrounding the
calls to reset framework functions, since it will either be a valid pointer, an
error pointer in the case where we called reset_get_optional without an of_node
pointer or if it failed, or NULL if we're not loaded through DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
we use IS_ERR_VALUE to check for error values of pm_runtime_get_sync,
when the value can only be < 0 in the case of err. Replace the
check with a simpler < 0 check.
This fixes the coccicheck warnings:
linux-2.6/drivers/i2c/busses/i2c-omap.c:1157:5-24:
pm_runtime_get_sync returns < 0 as error. Unecessary IS_ERR_VALUE at
line 1158
linux-2.6/drivers/i2c/busses/i2c-omap.c:1278:7-26:
pm_runtime_get_sync returns < 0 as error. Unecessary IS_ERR_VALUE at
line 1279
drivers/i2c/busses/i2c-omap.c:638:5-24:
pm_runtime_get_sync returns < 0 as error. Unecessary IS_ERR_VALUE at
line 639
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This was tested on a EFM32GG-DK3750 devboard that has a temperature
sensor and an eeprom on its i2c bus.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes a build break due to the undeclared use of irq_of_parse_and_map()
and of_iomap(). This build break was apparently introduced while the
driver was unbuildable due to the bug fixed by
62c19c9d29 ("i2c: Remove usage of
orphaned symbol OF_I2C"). When 62c19c was added in v3.14-rc7,
the driver was enabled again, breaking the powerpc mpc85xx_defconfig
and mpc85xx_smp_defconfig.
62c19c is marked for stable, so this should go there as well.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The symbol is an orphan, don't depend on it anymore.
Signed-off-by: Richard Weinberger <richard@nod.at>
[wsa: enhanced commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 687b81d083 (i2c: move OF helpers into the core)
Cc: stable@kernel.org
Remove unnecessary cast of void pointer, because 'algo_data' of
'struct i2c_adapter' is a void pointer. Casting the void pointer
is redundant. The conversion from void pointer to any other
pointer type is guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
warning: 'exynos5_i2c_suspend_noirq' defined but not used [-Wunused-function]
warning: 'exynos5_i2c_resume_noirq' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When using device-tree and the i2c-gpio driver is called before the
GPIO node has been probed then it needs to correctly defer the probe
instead of returning a permanent error that the gpio numbers are not
valid.
This fixes the following error:
/i2c@2: invalid GPIO pins, sda=-517/scl=-517
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is a rather odd feature of the exynos i2c controller that if it
is left enabled, it can lock itself up with the clk line held low.
This makes the bus unusable.
Unfortunately, the s3c24xx_i2c_set_master() function does not notice
this, and reports a timeout. From then on the bus cannot be used until
the AP is rebooted.
The problem happens when any sort of interrupt occurs (e.g. due to a
bus transition) when we are not in the middle of a transaction. We
have seen many instances of this when U-Boot leaves the bus apparently
happy, but Linux cannot access it.
The current code is therefore pretty fragile.
This fixes things by leaving the bus disabled unless we are actually
in a transaction. We enable the bus at the start of the transaction and
disable it at the end. That way we won't get interrupts and will not
lock up the bus.
It might be possible to clear pending interrupts on start-up, but this
seems to be a more robust solution. We can't service interrupts when
we are not in a transaction, and anyway would rather not lock up the
bus while we try.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
This adds the ability to set "clock-frequency" in the device tree for the at91
i2cbus following the naming of other i2c bus implementations. If the property
is not set,the clock frequency will default to the previously used define
of 100KHz.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Intel BayTrail, there was case whereby the resulting fast mode
bus speed becomes slower (~20% slower compared to expected speed)
if using the HCNT/LCNT calculated in the core layer. Thus, this
patch is added to allow pci glue layer to pass in optimal
HCNT/LCNT/SDA hold time values to core layer since the core
layer supports cofigurable HCNT/LCNT/SDA hold time values now.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch fixes the error returned to the i2c_transfer function
to -EAGAIN in case of arbitratin lost, so that the retry mechanism
can be used.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We now have a central place to put this code to.
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Calling the state machine with a definite state which is only used in
this context is superfluous. Do it directly.
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For start and restart, we are doing the same thing. Let's consolidate
that.
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All the I2C controllers on Intel BayTrail LPSS subsystem able
to support 10-bit addressing mode functionality.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Signed-off-by: Ong, Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_ioremap_resource() in order to make the code simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_ioremap_resource() in order to make the code simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add Device ID of Intel BayTrail SMBus Controller.
Signed-off-by: Chew, Kean ho <kean.ho.chew@intel.com>
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Intel Baytrail I2C controllers can be enumerated from PCI as well as from
ACPI. In order to support this add the Baytrail PCI IDs to the driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The PCI part of the DesignWare I2C driver does a lot of things that are not
required anymore. For example drivers aren't supposed to handle PCI state
transitions themselves. This is all provided by the PCI bus core already.
In addition to that there is no point scheduling RPM suspend on driver's
idle hook but instead we can use RPM autosuspend for this (which is enabled
in the driver already).
As a bonus, this patch also fixes following compile warning which is
emitted when the driver was compiled without CONFIG_PM_RUNTIME set:
drivers/i2c/busses/i2c-designware-pcidrv.c:245:12: warning: ‘i2c_dw_pci_runtime_idle’ defined but not used [-Wunused-function]
Reported-by: xinhui.pan <xinhuix.pan@intel.com>
Reported-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch allows to set independantly SCL and SDA falling times.
The tLOW period is computed by taking into account the SCL falling time.
The tHIGH period is computed by taking into account the SDA falling time.
For instance in case the margin on tLOW is considered too small, it can
be increased by increasing the SCL falling time which is by default set
at 300ns.
The same applies for tHIGH period with the help of SDA falling time.
Signed-off-by: Romain Baeriswyl <romainba@abilis.com>
Reviewed-by: Christian Ruppert <christian.ruppert@abilis.com>
Acked-by: Shinya Kuribayashi <skuribay@pobox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Put necessary SSYNC code into blackfin twi arch header. The generic TWI
driver should not contain any architecture specific code.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The ADI TWI peripheral is not binding to the Blackfin processor only.
The bits macros and structs should be put in the generic include header.
And update head file path in drivers accordingly.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Allwinner A31 I2C controller is almost identical to the one used in the
other Allwinner SoCs, except for the fact that it needs to clear the interrupt
by setting the INT_FLAGS bit in the control register, instead of clearing it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Allwinner A31 SoC using that IP has a reset controller maintaining
it reset unless told otherwise.
Add some optional reset support to the driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We should never be busy performing transfers at suspend late, thus
there are no reason to check for it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
At system suspend_late, runtime PM has been disabled by the PM core
which means we can safely operate on these resources. Consequentially
we no longer have to wait until the noirq phase of the system suspend.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since the runtime PM state is expected to be active according to the
amba bus, we must align our behaviour while probing to it.
Moreover, this is needed to be able to have the driver fully functional
without depending on CONFIG_RUNTIME_PM.
Since the device is active while a successful probe has been completed,
the reference counting for the clock will be screwed up and never reach
zero. We resolve this by implementing runtime PM callbacks and let them
handle the resources accordingly, including the clock.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[wsa: s/#if/#ifdef/]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The amba bus are responsible for pm_runtime_enable|disable, remove the
redundant pm_runtime_disable at driver removal.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_* functions to simplify code and error handling.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move the former platform data struct nmk_i2c_controller into the
per-device state container struct i2c_nmk_client, and remove all
the platform data probe path hacks.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[wsa: use 100kHz as default]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
While we are here, also brush up the devicetree binding documentation.
The example was an inappropriate copy from the sh_mobile driver.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Because the offload mechanism can fall back to a standard transfer,
having two seperate initialization states is unfortunate. Let's just
have one state which does things consistently. This fixes a bug where
some preparation was missing when the fallback happened. And it makes
the code much easier to follow. To implement this, we put the check
if offload is possible at the top of the offload setup function.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: stable@vger.kernel.org # v3.12+
Fixes: 930ab3d403 (i2c: mv64xxx: Add I2C Transaction Generator support)
Pull more i2c updates from Wolfram Sang:
"Mostly bugfixes, small but wanted cleanups, and Paul's init.h removal
applied"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: rcar: fix NACK error code
i2c: update i2c_algorithm documentation
i2c: rcar: use devm_clk_get to ensure clock is properly ref-counted
i2c: rcar: do not print error if device nacks transfer
i2c: rely on driver core when sanitizing devices
i2c: delete non-required instances of include <linux/init.h>
i2c: acorn: is tristate and should use module.h
i2c: piix4: Standardize log messages
i2c: piix4: Use different message for AMD Auxiliary SMBus Controller
i2c: piix4: Add support for AMD ML and CZ SMBus changes
Pull hwmon updates from Jean Delvare:
"This include it87 driver improvements, and a tree-wide change of my
e-mail address"
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
Update Jean Delvare's e-mail address
hwmon: (it87) Print proper names for the IT8771E and IT8772E
hwmon: (it87) Add support for the ITE IT8603E
The response to a bus NACK is to return -ENXIO instead of the
-EREMOTEIO being currently returned by the driver.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The current i2c-rcar driver does clk_get() without a corresponding
clk_put(). Add the clk to the driver private data and then get it
with the devm functions so that it is released when the driver is
unbound.
Note, we do not call clk_prepare_enable() at this point due to the
very possible magic that is being done by the pm_runtime system
underneath the driver.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-rcar driver currently prints an error message if the master_xfer
callback fails. However if the bus is being probed then lots of NAKs
will be generated, causing the output of a number of errors printed.
To solve this, disable the print if the error is not -EREMOTEIO.
An example of running i2cdetect:
10: i2c-rcar e6530000.i2c: error -121 : 15
-- i2c-rcar e6530000.i2c: error -121 : 15
-- 12 i2c-rcar e6530000.i2c: error -121 : 15
-- i2c-rcar e6530000.i2c: error -121 : 15
-- i2c-rcar e6530000.i2c: error -121 : 15
-- i2c-rcar e6530000.i2c: error -121 : 15
-- i2c-rcar e6530000.i2c: error -121 : 15
-- i2c-rcar e6530000.i2c: error -121 : 15
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This file is controlled by a tristate Kconfig option, and hence
needs to include module.h so that it can get module_init() once
we relocate it from init.h into module.h in the future.
Note that module_exit() appears to be missing from the driver, so
it is questionable whether it would actually work for a removal
and reload cycle if it was configured for a modular build.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use exactly the same log messages in the legacy setup function and the
SB800+ setup function. This way strings can be reused, which saves
some bytes in the generated binary.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Same messages for AMD main and auxiliary SMBus controllers lead to confusion,
this patch is to remove confusion and keep consistent with non-AMD products.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The locations of SMBus register base address and enablement bit are changed
from AMD ML, which need this patch to be supported.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org
This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep it
strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared with Mike
Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for multiplatform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJS4Vf7AAoJEIwa5zzehBx3f9UP/jwMlbfbSZHfNQ/QG0SqZ9RD
zvddyDMHY/qXnzgF3Dax+JR9BDDVy8AlQe713FCoiHJZggWRAbbavkx8gxITDrZQ
6NYaEkkuVxqyM8APl3PwMqYm8UZ8MUf4lCltlOA4jkesY9vue91AFnfyKh2CvHrn
Leg4XT6mFzf/vYDL6RbvTz/Qr253uv3KvYBxkeiRNa0Y7OXRemEXSOfgxh0YGxUl
LZ2IWQFOh/DH4kaeQI8V4G67X3ceHiFyhCnl0CPwfxaZaNBVaxvIFgIUTdetS6Sb
zcXa029tE/Dfsr55vZAv9LUHEipCSOeE5rn2EJWehTWyM7vJ42Eozqgh+zfCjXS7
Ib6g2npsvIluQit/RdITu44h5yZlrQsLgKTGJ8jjXqbT4HQ/746W8b/TP0YLtbw7
N8oqr7k4vsZyF0dAYZQtfQUZeGISz67UbFcdzl9tmYOR7HFuAYkAQYst77zkVJf8
om59BAYYTG5FNjQ4I9AKUfJzxXYveI6AKpXSCCZiahpFM2D1CJIzp9Wi0GwK1HRR
sFVWhS0dajvz63pVVC2tw5Sq4J7onRRNGIXFPoE5fkmlelm0/q0zzGjw3Z0nTqbZ
8zxuwuy2FfPJK11GbUAIhAgn1sCLYyAhl6IE+FsanGeMOSGIMrH0v5/HphAxoCXt
BvqMDogyLoGPce1Gm3pJ
=3CcT
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep
it strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared
with Mike Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for
multiplatform"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
ARM: mvebu: remove prototypes of non-existing functions from common.h
ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
...
As usual, we have a batch of fixes that weren't considered significant
enough to warrant going into the later -rcs for previous release, so
they are queued up on this branch.
A handful of these are for various DT fixups for Samsung platforms,
and a handful of other minor things.
There are also a couple of stable-marked patches for mvebu -- they came in
quite late and we decided to keep them deferred until the first -stable
release to get more coverage instead of squeezing them into 3.13.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=QhN9
-----END PGP SIGNATURE-----
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical fixes from Olof Johansson:
"As usual, we have a batch of fixes that weren't considered significant
enough to warrant going into the later -rcs for previous release, so
they are queued up on this branch.
A handful of these are for various DT fixups for Samsung platforms,
and a handful of other minor things.
There are also a couple of stable-marked patches for mvebu -- they
came in quite late and we decided to keep them deferred until the
first -stable release to get more coverage instead of squeezing them
into 3.13"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
ARM: at91: smc: bug fix in sam9_smc_cs_read()
i2c: mv64xxx: Document the newly introduced Armada XP A0 compatible
i2c: mv64xxx: Fix bus hang on A0 version of the Armada XP SoCs
ARM: mvebu: Add quirk for i2c for the OpenBlocks AX3-4 board
ARM: mvebu: Add support to get the ID and the revision of a SoC
ARM: dts: msm: Fix gpio interrupt and reg length
irqchip: sirf: set IRQ_LEVEL status_flags
ARM: OMAP2+: gpmc: Move legacy GPMC width setting
ARM: OMAP2+: gpmc: Introduce gpmc_set_legacy()
ARM: OMAP2+: gpmc: Move initialization outside the gpmc_t condition
ARM: OMAP2+: board-generic: update SoC compatibility strings
Documentation: dt: OMAP: explicitly state SoC compatible strings
ARM: OMAP2+: enable AM33xx SOC EVM audio
ARM: OMAP2+: Select USB PHY for AM335x SoC
ARM: bcm2835: Fix grammar in help message
ARM: msm: trout: fix uninit var warning
ARM: dts: Use MSHC controller for eMMC memory for exynos4412-trats2
ARM: dts: Fix definition of MSHC device tree nodes for exynos4x12
ARM: dts: add clock provider for mshc node for Exynos4412 SOC
clk: samsung: exynos4: Fix definition of div_mmc_pre4 divider
...
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science stuff from trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
neighbour.h: fix comment
sched: Fix warning on make htmldocs caused by wait.h
slab: struct kmem_cache is protected by slab_mutex
doc: Fix typo in USB Gadget Documentation
of/Kconfig: Spelling s/one/once/
mkregtable: Fix sscanf handling
lp5523, lp8501: comment improvements
thermal: rcar: comment spelling
treewide: fix comments and printk msgs
IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
Documentation: update /proc/uptime field description
Documentation: Fix size parameter for snprintf
arm: fix comment header and macro name
asm-generic: uaccess: Spelling s/a ny/any/
mtd: onenand: fix comment header
doc: driver-model/platform.txt: fix a typo
drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
doc: Fix typo (acces_process_vm -> access_process_vm)
treewide: Fix typos in printk
drivers/gpu/drm/qxl/Kconfig: reformat the help text
...
If used 64 bit compiler GCC warns that:
drivers/i2c/busses/i2c-s3c2410.c: In function ‘s3c24xx_get_device_quirks’:
drivers/i2c/busses/i2c-s3c2410.c:168:10: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
This patch fixes this by converting "unsigned int" to "kernel_ulong_t".
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_*() functions to make cleanup paths simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- mvebu
- fix boot hang on Armada XP due to broken i2c offloading in A0 SoC revision
(specifically experienced on some early OpenBlocks AX3-4 boards)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=tliU
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-3.13' of git://git.infradead.org/linux-mvebu into next/fixes-non-critical
From Jason Cooper:
mvebu late fixes for v3.13
- mvebu
- fix boot hang on Armada XP due to broken i2c offloading in A0 SoC revision
(specifically experienced on some early OpenBlocks AX3-4 boards)
* tag 'mvebu-fixes-3.13' of git://git.infradead.org/linux-mvebu:
i2c: mv64xxx: Document the newly introduced Armada XP A0 compatible
i2c: mv64xxx: Fix bus hang on A0 version of the Armada XP SoCs
ARM: mvebu: Add quirk for i2c for the OpenBlocks AX3-4 board
ARM: mvebu: Add support to get the ID and the revision of a SoC
Signed-off-by: Kevin Hilman <khilman@linaro.org>
The first variants of Armada XP SoCs (A0 stepping) have issues related
to the i2c controller which prevent to use the offload mechanism and
lead to a kernel hang during boot.
The commit introduces a new the compatible string
marvell,mv78230-a0-i2c for the i2c controller. When this compatible
string is used the driver disables the offload mechanism and the
kernel no more hangs on these SoCs.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reported-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org # v3.12+: af8d1c63afcb: ARM: mvebu: Add support to get the ID and the revision of a SoC
Cc: stable@vger.kernel.org # v3.12+: 85e618a1be2b: ARM: mvebu: Add quirk for i2c for the OpenBlocks AX3-4 board
Cc: stable@vger.kernel.org # v3.12+
Fixes: 930ab3d403 (i2c: mv64xxx: Add I2C Transaction Generator support)
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds the support of the I2C_SMBUS_I2C_BLOCK_DATA transaction
type for the iSMT SMBus Controller.
Signed-off-by: Robert Valiquette <robert.valiquette@intel.com>
Acked-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
OSIF, Open Source InterFace, is a USB based i2c bus master. The
origional design was based on i2c-tiny-usb, but more modern versions
of the firmware running on the MegaAVR microcontroller use a different
protocol over the USB. This code is based on Barry Carter
<barry.carter@gmail.com> driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The RobotFuzz device is not compatible with i2c-tiny-usb. Remove its
entry from the USB table so that the new correct driver can be used.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since 93abe8e4 (clk: add non CONFIG_HAVE_CLK routines) code using clk.h
like this platform driver need not depend on HAVE_CLK. Also, remove a
redundant clk.h include from core driver.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Nomadik I2C is now configured from the device tree on all platforms
using this controller. Delete the platform data header and move the
definitions into the driver so it is all contained in one single file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Nomadik I2C controller needs to have the slave set-up time
configured based off the clock used to drive the I2C bus block.
Currently this is done with static assignments assuming that the
block is clocked 48MHz which is pretty likely to be bug-prone.
Calculate the SLSU from the equation given in the datasheet
instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
cppcheck rightfully says:
drivers/i2c/busses/i2c-viperboard.c:169: style: Variable 'bytes_xfer' is assigned a value that is never used.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Lars Poeschel <poeschel@lemonage.de>
This patch fixed several typo in printk from various
part of kernel source.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Simplified the probe and remove functions using devm_* functions
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
IRQ handler has to be register first before IRQ
is enabled in xiic_reinit().
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Code changes to fix checkpatch warnings listed below.
- WARNING: please, no space before tabs
- WARNING: quoted string split across lines
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_request_region() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_kzalloc() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
smatch rightfully says:
drivers/i2c/busses/i2c-imx.c:610 i2c_imx_probe() info: why not propagate 'irq' from platform_get_irq() instead of (-2)?
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For Exynos4 and Exynos5 SoCs from Samsung the i2c clock is based
on a fixed 66 MHz peripheral clock, and therefore is completely
independent of the cpu frequency.
Thus, registering for a CPU freq notifier is very wasteful.
This patch modifes the code such that, i2c bus registers to
cpu_freq_transition only if CONFIG_CPU_FREQ_S3C24XX is enabled.
This change should save a bunch of cpufreq transitions calls
which does not apply to exynos SoCs.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds polling mode support for i2c-s3c2410 driver.The
SATA PHY controller's CMU and TRSV block's are of I2C register
map in exynos5250.These blocks can be configured using i2c.
But i2c controller instance on which these block's sits lacks an
interrupt line.Also the current i2c-s3c2410 driver is only interrupt
driven, thus a polling mode support is required in the driver for
supporting this controller. This patch adds this support to the driver.
Signed-off-by: Vasanth Ananthan <vasanth.a@samsung.com>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Hardware supported by the i2c sh_mobile and rcar drivers is only found
on SUPERH or ARCH_SHMOBILE platforms. Restrict non-COMPILE_TEST
compilation to them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested with a r7s72100 genmai board acessing an eeprom.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8T7+
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
From Stephen Warren:
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
* tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (30 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Correct spelling typo in various part of kernel
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Pull i2c fixes from Wolfram Sang:
"Some easy but needed fixes for i2c drivers since rc1"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: bcm2835: Linking platform nodes to adapter nodes
i2c: omap: raw read and write endian fix
i2c: i2c-bcm-kona: Fix module build
i2c: i2c-diolan-u2c: different usb endpoints for DLN-2-U2C
i2c: bcm-kona: remove duplicated include
i2c: davinci: raw read and write endian fix
In order to find I2C devices in the device tree, the platform nodes
have to be known by the I2C core. This requires setting the
dev.of_node parameter of the adapter.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All OMAP IP blocks expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.
Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Correct a typo that prevented the driver from being built as a module.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The previous diolan adapter uses other out/in endpoints than
the current DLN-2-U2C in compatibility mode.
They changed from 0x2/0x84 to 0x3/0x83.
This patch gets the endpoints from the usb interface, instead
of hardcode them in the driver.
This was tested on a current DLN-2-U2C board.
Signed-off-by: Martin Vogt <mvogt1@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C IP block expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.
Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
From Tony Lindgren:
Few more fixes for issues found booting older omaps using device tree.
Also few randconfig build fixes and removal of some dead code for omap4
as it no longer has legacy platform data based booting support.
* tag 'omap-for-v3.13/more-fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
Pull i2c changes from Wolfram Sang:
- new drivers for exynos5, bcm kona, and st micro
- bigger overhauls for drivers mxs and rcar
- typical driver bugfixes, cleanups, improvements
- got rid of the superfluous 'driver' member in i2c_client struct This
touches a few drivers in other subsystems. All acked.
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: bcm-kona: fix error return code in bcm_kona_i2c_probe()
i2c: i2c-eg20t: do not print error message in syslog if no ACK received
i2c: bcm-kona: Introduce Broadcom I2C Driver
i2c: cbus-gpio: Fix device tree binding
i2c: wmt: add missing clk_disable_unprepare() on error
i2c: designware: add new ACPI IDs
i2c: i801: Add Device IDs for Intel Wildcat Point-LP PCH
i2c: exynos5: Remove incorrect clk_disable_unprepare
i2c: i2c-st: Add ST I2C controller
i2c: exynos5: add High Speed I2C controller driver
i2c: rcar: fixup rcar type naming
i2c: scmi: remove some bogus NULL checks
i2c: sh_mobile & rcar: Enable the driver on all ARM platforms
i2c: sh_mobile: Convert to clk_prepare/unprepare
i2c: mux: gpio: use reg value for i2c_add_mux_adapter
i2c: mux: gpio: use gpio_set_value_cansleep()
i2c: Include linux/of.h header
i2c: mxs: Fix PIO mode on i.MX23
i2c: mxs: Rework the PIO mode operation
i2c: mxs: distinguish i.MX23 and i.MX28 based I2C controller
...
Fix to return a negative error code from the bus speed parse
error handling case instead of 0.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Using the i2c-eg20t driver and call i2cdetect or probe on the bus,
the driver will print a lot of error messages if there was no ACK
received.
i2cdetect normally print a table with all the available devices. If there
is no device on the address, the table will be empty.
Currently with the i2c-eg20t driver, the table is not visible because
the error messages destroy the table.
Error message: pch_i2c_getack return -71
This patch prevent the driver to print the messages to syslog.
The pch_i2c_wait_for_check_xfer function is the only one who is
calling pch_i2c_getack, so we can delete the function and add the
read to pch_i2c_wait_for_check_xfer.
If no ACK is received, the Message will be printed as a dbg
message.
Fixed print message to be a one liner so we can grep for the
error message.
Tested on Intel Atom E6xx and Eg20t Chipset.
Signed-off-by: Andreas Werner <wernerandy@gmx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Introduce support for Broadcom Serial Controller (BSC) I2C bus found
in the Kona family of Mobile SoCs. FIFO hardware is utilized but only
standard mode (100kHz), fast mode (400kHz), fast mode plus (1MHz), and
I2C high-speed (3.4 MHz) bus speeds are supported.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
[wsa: fixed Kconfig sorting, squashed broken out patches into one]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As we claim to support device tree for mach-omap2, we
should have the necessary flags in the driver to make it
usable.
Cc: linux-i2c@vger.kernel.org
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we're missing two lines needed to make it
work properly with device tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the missing clk_disable_unprepare() before return
from wmt_i2c_reset_hardware() in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org # 3.11+
Newer Intel PCHs with LPSS have the same Designware I2C controllers than
Haswell but the ACPI IDs differ. Add these IDs to the driver list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds the SMBus Device IDs for the Intel Wildcat Point-LP PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds support to SSC (Synchronous Serial Controller)
I2C driver. This IP also supports SPI protocol, but this is not
the aim of this driver.
This IP is embedded in all ST SoCs for Set-top box platorms, and
supports I2C Standard and Fast modes.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Adds support for High Speed I2C driver found in Exynos5 and
later SoCs from Samsung.
Driver only supports Device Tree method.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Taekgyun Ko <taeggyun.ko@samsung.com>
Reviewed-by: Simon Glass <sjg@google.com>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Andrew Bresticker <abrestic@google.com>
[wsa: rebased to v3.12-rc4 (no of_i2c.h anymore)]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
b720423a26
(i2c: rcar: add rcar-H2 support)
added R-Car H2 support on i2c-rcar.
The R-Car I2C type is based on SoC generation
(Gen1 = E1/M1/H1, Gen2 = E2/M2/H2),
but added naming was H1/H2 instead of Gen1/Gen2.
Gen1/Gen2 is better naming on this driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
"obj" can't be NULL here.
We already know that "pkg->package.elements" gives us a valid pointer
so the next pointer after that is also non-NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Renesas ARM platforms are transitioning from single-platform to
multi-platform kernels using the new ARCH_SHMOBILE_MULTI. Make the
driver available on all ARM platforms to enable it on both ARCH_SHMOBILE
and ARCH_SHMOBILE_MULTI, and increase build testing coverage with
COMPILE_TEST.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Turn clk_enable() and clk_disable() calls into clk_prepare_enable() and
clk_disable_unprepare() to get ready for the migration to the common
clock framework.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Replace some instances of of_irq_map_one()/irq_create_of_mapping() and
of_irq_to_resource() by the simpler equivalent irq_of_parse_and_map().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
[grant.likely: resolved conflicts with core code renames]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Initially commit cb527ede1b
"i2c-omap: Double clear of ARDY status in IRQ handler"
added a workaround for undocumented errata ProDB0017052.
But then commit 1d7afc9594
"i2c: omap: ack IRQ in parts" refactored code and missed
one of ARDY clearings. So current code violates errata.
It causes often i2c bus timeouts on my Pandaboard.
This patch adds a second clearing in place.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Subsystems like pinctrl and gpio rightfully make use of deferred probing at
core level. Now, deferred drivers won't be retried if they don't have a .probe
function specified in the driver struct. Fix this driver to have that, so the
devices it supports won't get lost in a deferred probe.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Subsystems like pinctrl and gpio rightfully make use of deferred probing at
core level. Now, deferred drivers won't be retried if they don't have a .probe
function specified in the driver struct. Fix this driver to have that, so the
devices it supports won't get lost in a deferred probe.
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Subsystems like pinctrl and gpio rightfully make use of deferred probing at
core level. Now, deferred drivers won't be retried if they don't have a .probe
function specified in the driver struct. Fix this driver to have that, so the
devices it supports won't get lost in a deferred probe.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Subsystems like pinctrl and gpio rightfully make use of deferred probing at
core level. Now, deferred drivers won't be retried if they don't have a .probe
function specified in the driver struct. Fix this driver to have that, so the
devices it supports won't get lost in a deferred probe.
Reported-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
The i.MX23 I2C controller is also capable of PIO, but needs a little harder
push to behave. The controller needs to be reset after every PIO/DMA operation
for some reason, otherwise in rare cases, the controller can hang or emit
bytes onto the bus.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Analyze and rework the PIO mode operation. The PIO mode operation
was unreliable on MX28, by analyzing the bus with LA, the checks
for when data were available or were to be sent were wrong.
The PIO WRITE has to be completely reworked as it multiple problems.
The MX23 datasheet helped here, see comments in the code for details.
The problems boil down to:
- RUN bit in CTRL0 must be set after DATA register was written
- The PIO transfer must be 4 bytes long tops, otherwise use
clock stretching.
Both of these fixes are implemented.
The PIO READ operation can only be done for up to four bytes as
we are unable to read out the data from the DATA register fast
enough.
This patch also tries to document the investigation within the
code.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It seems the PIO mode does not work, or at least not like it works
on a i.MX28. Each short transfer needs about one second (without an
error message) but does not send anything on the I2C lines.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Using the same clock for all device instances is non-portable and obtaining
clock references by an ID without using a device pointer is discouraged.
This is also not needed, because on platforms, where this driver is used,
suitable clocks are available for the I2C controllers, that are children of
the peripheral clock and just pass its rate 1-to-1 to controllers. This
patch switches the driver to obtain references to correct clocks.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When clk_get() fails, it returns an error code, not a NULL. This patch
fixes such an error handling bug.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds Device Tree support to the i2c-rcar driver and respective
documentation.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no need to repeatedly query clock frequency, where it is not
expected to change. The complete loop can also trivially be replaced with
a simple division. A further loop below the one, being simplified, could
also be replaced, but that would get more complicated.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
A recent patch added even more superfluous parenthesis to those, which
already were there. Remove them again.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds code to initialize the DMA buffer to compensate for
possible hardware data corruption.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
[wsa: changed to use 'sizeof']
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to Designware I2C spec, if I2C_DYNAMIC_TAR_UPDATE is set to 1,
the 10-bit addressing mode is controlled by IC_10BITADDR_MASTER bit of
IC_TAR register instead of IC_CON register. The IC_10BITADDR_MASTER
in IC_CON register becomes read-only copy. Since I2C_DYNAMIC_TAR_UPDATE
value can't be detected from hardware register, so we will always set the
IC_10BITADDR_MASTER bit in both IC_CON and IC_TAR register whenever 10-bit
addresing mode is requested by user application.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver is used on PowerPC which don't provide writel_relaxed(). This
breaks the c2k and prpmc2800 default configurations. To fix the build,
turn the calls to writel_relaxed() into writel(). The impacts for ARM
should be minimal.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some functions and variables are only used if the configuration selects
HAVE_CLK. Protect them with a corresponding #ifdef CONFIG_HAVE_CLK block
to avoid compiler warnings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
[wsa: added marker to #endif]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
commit d16933b339 "i2c: s3c2410: Move
location of clk_prepare_enable() call in probe function" refactored
clk_enable and clk_disable calls yet neglected to remove the
clk_disable_unprepare call in the module's remove().
It helps remove warnings on an arndale during unbind:
echo 12c90000.i2c > /sys/bus/platform/devices/12c90000.i2c/driver/unbind
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2548 at drivers/clk/clk.c:842 clk_disable+0x18/0x24()
Modules linked in:
CPU: 0 PID: 2548 Comm: bash Not tainted 3.11.0-next-20130916-00003-gf4bddbc #6
[<c0014d48>] (unwind_backtrace+0x0/0xf8) from [<c00117d0>] (show_stack+0x10/0x14)
[<c00117d0>] (show_stack+0x10/0x14) from [<c0361be8>] (dump_stack+0x6c/0xac)
[<c0361be8>] (dump_stack+0x6c/0xac) from [<c001d864>] (warn_slowpath_common+0x64/0x88)
[<c001d864>] (warn_slowpath_common+0x64/0x88) from [<c001d8a4>] (warn_slowpath_null+0x1c/0x24)
[<c001d8a4>] (warn_slowpath_null+0x1c/0x24) from [<c02c4a64>] (clk_disable+0x18/0x24)
[<c02c4a64>] (clk_disable+0x18/0x24) from [<c028d0b0>] (s3c24xx_i2c_remove+0x28/0x70)
[<c028d0b0>] (s3c24xx_i2c_remove+0x28/0x70) from [<c0217a10>] (platform_drv_remove+0x18/0x1c)
[<c0217a10>] (platform_drv_remove+0x18/0x1c) from [<c0216358>] (__device_release_driver+0x58/0xb4)
[<c0216358>] (__device_release_driver+0x58/0xb4) from [<c02163d0>] (device_release_driver+0x1c/0x28)
[<c02163d0>] (device_release_driver+0x1c/0x28) from [<c02153c0>] (unbind_store+0x58/0x90)
[<c02153c0>] (unbind_store+0x58/0x90) from [<c0214c90>] (drv_attr_store+0x20/0x2c)
[<c0214c90>] (drv_attr_store+0x20/0x2c) from [<c01032c0>] (sysfs_write_file+0x168/0x198)
[<c01032c0>] (sysfs_write_file+0x168/0x198) from [<c00ae1c0>] (vfs_write+0xb0/0x194)
[<c00ae1c0>] (vfs_write+0xb0/0x194) from [<c00ae594>] (SyS_write+0x3c/0x70)
[<c00ae594>] (SyS_write+0x3c/0x70) from [<c000e3e0>] (ret_fast_syscall+0x0/0x30)
---[ end trace 4c9f9403066f57a6 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2548 at drivers/clk/clk.c:751 clk_unprepare+0x14/0x1c()
Modules linked in:
CPU: 0 PID: 2548 Comm: bash Tainted: G W 3.11.0-next-20130916-00003-gf4bddbc #6
[<c0014d48>] (unwind_backtrace+0x0/0xf8) from [<c00117d0>] (show_stack+0x10/0x14)
[<c00117d0>] (show_stack+0x10/0x14) from [<c0361be8>] (dump_stack+0x6c/0xac)
[<c0361be8>] (dump_stack+0x6c/0xac) from [<c001d864>] (warn_slowpath_common+0x64/0x88)
[<c001d864>] (warn_slowpath_common+0x64/0x88) from [<c001d8a4>] (warn_slowpath_null+0x1c/0x24)
[<c001d8a4>] (warn_slowpath_null+0x1c/0x24) from [<c02c5834>] (clk_unprepare+0x14/0x1c)
[<c02c5834>] (clk_unprepare+0x14/0x1c) from [<c028d0b8>] (s3c24xx_i2c_remove+0x30/0x70)
[<c028d0b8>] (s3c24xx_i2c_remove+0x30/0x70) from [<c0217a10>] (platform_drv_remove+0x18/0x1c)
[<c0217a10>] (platform_drv_remove+0x18/0x1c) from [<c0216358>] (__device_release_driver+0x58/0xb4)
[<c0216358>] (__device_release_driver+0x58/0xb4) from [<c02163d0>] (device_release_driver+0x1c/0x28)
[<c02163d0>] (device_release_driver+0x1c/0x28) from [<c02153c0>] (unbind_store+0x58/0x90)
[<c02153c0>] (unbind_store+0x58/0x90) from [<c0214c90>] (drv_attr_store+0x20/0x2c)
[<c0214c90>] (drv_attr_store+0x20/0x2c) from [<c01032c0>] (sysfs_write_file+0x168/0x198)
[<c01032c0>] (sysfs_write_file+0x168/0x198) from [<c00ae1c0>] (vfs_write+0xb0/0x194)
[<c00ae1c0>] (vfs_write+0xb0/0x194) from [<c00ae594>] (SyS_write+0x3c/0x70)
[<c00ae594>] (SyS_write+0x3c/0x70) from [<c000e3e0>] (ret_fast_syscall+0x0/0x30)
---[ end trace 4c9f9403066f57a7 ]---
Signed-off-by: Kim Phillips <kim.phillips@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
commit 6d4028c644 (i2c: use dev_get_platdata()) did a bad conversion
of this one case:
drivers/i2c/busses/i2c-davinci.c: In function 'davinci_i2c_probe':
drivers/i2c/busses/i2c-davinci.c:665:2: warning: passing argument 1 of
'dev_get_platdata' from incompatible pointer type [enabled by default]
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch modify I2C driver of rcar-H1 to usable on both rcar-H1 and rcar-H2.
Signed-off-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
let i2c core retry 3 times as sometimes we get random noack and timeout
even when we access an existing i2c client.
Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
if users set I2C_M_REV_DIR_ADDR, revert the direction of address.
Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
there is a typo before, it makes the final bitrate wrong, this patch fixes
it.
Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
this fixes the issue that we lost to wait the i2c reset finished.
Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Due to hardware ANOMALY, we need to reset I2C earlier after
we get NOACK while accessing non-existing clients, otherwise
we will get errors even we access existing clients later
Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some Intel LPSS I2C devices make the SDA hold time and *CNT parameters
available via SSCN (standard mode) and FMCN (fast mode) ACPI methods.
Implement support for this so that we check whether an ACPI method exists
and if it does, fill in the SDA hold time and *CNT values to the device
private structure for core to use.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The DesignWare I2C controller has high count (HCNT) and low count (LCNT)
registers for each of the I2C speed modes (standard and fast). These
registers are programmed based on the input clock speed in the driver.
The current code calculates these values based on the input clock speed and
tries hard to meet the I2C bus timing requirements. This could result
non-optimal values with regarding to the bus speed. For example on Intel
BayTrail we get bus speed of 315.41kHz which is ~20% slower than we would
expect (400kHz) in fast mode (even though the timing requirements are met).
This patch makes it possible for the platform code to pass more optimal
HCNT/LCNT values to the core driver if they are known beforehand. If these
are not set we use the calculated and more conservative values.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Shinya Kuribayashi <skuribay@pobox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
make the MPC I2C driver get, prepare and enable the gated clock item for
register access during probe; disable and unprepare the clock upon
remove(), put is done by the devm approach; hold a reference to the
clock over the period of use
clock lookup is non-fatal in this implementation as not all platforms
may provide clock specs in their device tree, but failure to enable a
clock when specified is considered fatal
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix to return a negative error code in the irq get error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
[wsa: fixed wrong exit point, too]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This follows what has already been done for the DeviceTree helpers. Move
the ACPI helpers from drivers/acpi/acpi_i2c.c to the I2C core and update
documentation accordingly.
This also solves a problem reported by Jerry Snitselaar that we can't build
the ACPI I2C helpers as a module.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C of helpers used to live in of_i2c.c but experience (from SPI) shows
that it is much cleaner to have this in the core. This also removes a
circular dependency between the helpers and the core, and so we can
finally register child nodes in the core instead of doing this manually
in each driver. So, fix the drivers and documentation, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All the Armada XP (mv78230, mv78260 and mv78460) have a silicon issue
in the I2C controller which violate the i2c repeated start
timing. The I2C standard requires a minimum of 4.7us for the repeated
start condition whereas the I2C controller of the Armada XP this time
is 2.9us.
So this patch adds a 5us delay for the start case only if the
the compatible i2c-mv78230 is set.
Based on the initals patches from Zbigniew Bodek
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Zbigniew Bodek <zbb@semihalf.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C Transaction Generator offloads CPU from managing I2C
transfer step by step.
This feature is currently only available on Armada XP, so usage of
this mechanism is activated through device tree.
Based on the work of Piotr Ziecik and rewrote to use the new way of
handling multiples i2c messages.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We want to bail out immediately if i2c_add_adapter failed and not try to
register child nodes with a nilled adapter structure.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Patch fixes i2c-tiny-usb not to use stack as URB transfer_buffer. URB buffers
need to be DMA-able, which stack is not.
Patch is only compile tested.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to I2C specification the NACK should be handled as folowing:
"When SDA remains HIGH during this ninth clock pulse, this is defined as the Not
Acknowledge signal. The master can then gene rate either a STOP condition to
abort the transfer, or a repeated START condition to start a new transfer."
[http://www.nxp.com/documents/user_manual/UM10204.pdf]
The same is recomened by TI I2C wiki:
http://processors.wiki.ti.com/index.php/I2C_Tips
Currently, the OMAP I2C driver interrupts I2C trunsfer in case of NACK, but
It queries Stop condition OMAP_I2C_CON_REG.STP=1 only if NACK has been received
during the last message transmitting/recieving.
This may lead to stuck Bus in "Bus Busy" until I2C IP reset (idle/enable).
Hence, fix it by querying Stop condition (STP) always when NACK is received.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Hein Tibosch <hein_tibosch@yahoo.es>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The timing calculation is rather bogus and gives extremely wrong
results for higher frequencies (on an i.MX28). E.g. instead of 400 kHz
I measured 770 kHz.
Implement a calculation that adheres to the I2C spec and gives exact
results for I2C frequencies from 12.56 kHz to 960 kHz.
Also the bus_free and leadin parameters are programmed according to
the I2C spec for standard and fast mode.
This was tested on a Ka-Ro TX28 module with a DS1339, TSC2007, PCA9554
and SGTL5000 client.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Marek Vasut <marex@denx.de>
[wsa: patch fixes whitespace issue, too]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more clear.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add Freescale Vybrid VF610 I2C controller support to
imx I2C driver framework.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This add struct imx_i2c_hwdata to hold more quirks data
which may vary between SoCs, thus the driver can operate
on more differences to support more SoCs.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This add bits operation macro that differ between SoCs.
Interrupt flags clear operation in I2SR differ between SoCs:
write zero to clear(w0c) INT flag on i.MX,
but write one to clear(w1c) INT flag on Vybrid.
I2C module enable operation in I2CR also differ between SoCs:
set I2CR_IEN bit enable the module on i.MX,
but clear I2CR_IEN bit enable the module on Vybrid.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
the I2C register offset may different between SoCs,
to provid support for all these chips, split the
register offset into a fixed base address and a
variable shift value, then the full register offset
will be calculated by
reg_off = ( reg_base_addr << reg_shift)
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
wrap the readb(), writeb() into inline function calls.
It would make the driver more clearer to support platform
with different register offset.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The id_entry field should be changed by platform driver core,
driver should prevent changing it derectly. Use local variable
to save and extract platform_device_id info of the dts devices
instead.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The module clk should be enabled before write to
its register in probe(), and the clk can be disabled
after.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
using struct representing the i2c clk{div, val} pair would
make the i2c_clk_div array more clear.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for the secondary SMBus controller on the AMD SB800 and AMD FCH
chipsets.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Tested-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Keystone SOCs uses the same I2C IP as available on DaVinci SOCs.
Update the config so that ARCH_KEYSTONE can use it.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver no longer uses definitions from mach/hardware.h.
On the other hand, including this header breaks this driver
on non-davinci platforms which don't have such a header.
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/i2c/busses/i2c-bfin-twi.c:585:12: warning: 'i2c_bfin_twi_suspend' defined but not used [-Wunused-function]
drivers/i2c/busses/i2c-bfin-twi.c:600:12: warning: 'i2c_bfin_twi_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add CONFIG_PM_SLEEP to suspend function to fix the following build
warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/i2c/busses/i2c-puv3.c:249:12: warning: 'puv3_i2c_suspend' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/i2c/busses/i2c-pnx.c:599:12: warning: 'i2c_pnx_controller_suspend' defined but not used [-Wunused-function]
drivers/i2c/busses/i2c-pnx.c:608:12: warning: 'i2c_pnx_controller_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/i2c/busses/i2c-stu300.c:945:12: warning: 'stu300_suspend' defined but not used [-Wunused-function]
drivers/i2c/busses/i2c-stu300.c:954:12: warning: 'stu300_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/i2c/busses/i2c-ocores.c:460:12: warning: 'ocores_i2c_suspend' defined but not used [-Wunused-function]
drivers/i2c/busses/i2c-ocores.c:471:12: warning: 'ocores_i2c_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/i2c/busses/i2c-designware-platdrv.c:211:12: warning: 'dw_i2c_suspend' defined but not used [-Wunused-function]
drivers/i2c/busses/i2c-designware-platdrv.c:221:12: warning: 'dw_i2c_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/i2c/busses/i2c-mpc.c:724:12: warning: 'mpc_i2c_suspend' defined but not used [-Wunused-function]
drivers/i2c/busses/i2c-mpc.c:734:12: warning: 'mpc_i2c_resume' defined but not used [-Wunused-function]
Also, this patch makes mpc_i2c_pm_ops static, because mpc_i2c_pm_ops
is not exported.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
stmp_reset_block() may fail, so let's check its return value and propagate it in
the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C adapters on Freescale MPC107/824x/85xx/512x/52xx/83xx/86xx all
have the same name "MPC adapter". Since I2C adapter numbers can change
across reboots and even after loading/unloading an I2C bus master driver,
adapter names have to be used to identify adapters and thus should be
unique and well defined. Since this is not the case with this driver,
it is difficult if not impossible to identify a specific adapter from
user space on affected platforms.
To remedy the problem, use the adapter memory address as part of the
adapter name.
With this patch, adapter names are:
On P2020:
MPC adapter at 0xfff703000
MPC adapter at 0xfff703100
On P5040:
MPC adapter at 0xffe118000
MPC adapter at 0xffe118100
MPC adapter at 0xffe119000
MPC adapter at 0xffe119100
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If both IC_EMPTYFIFO_HOLD_MASTER_EN and IC_RESTART_EN are set to 1, the
Designware I2C controller doesn't generate RESTART unless user specifically
requests it by setting RESTART bit in IC_DATA_CMD register.
Since IC_EMPTYFIFO_HOLD_MASTER_EN setting can't be detected from hardware
register, we must always manually set the restart bit between messages.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
To enter high speed mode, following steps should be done:
1. When running in high speed mode, i2c clock rate is different
from standard mode. Clock rate must be set according to
specification first.
2. When i2c controller sends a master code and wins arbitration,
high speed mode is entered.
If you want to enable high speed mode, the following members of
platform data should be set to proper value:
1. "high_mode" should be set to "1".
2. "master_code" should be set to "8'b 0000_1xxx"(x is 0 or 1).
If no master_code is set, set to default value 0xe.
3. "rate" should be set according to specification.
Signed-off-by: Leilei Shang <shangll@marvell.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add some necessary braces that have been removed during driver cleanup.
This fixes the I2C prescaler calculation.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Recently we have been seing some reports about PIO mode not working properly.
- http://www.spinics.net/lists/linux-i2c/msg11985.html
- http://marc.info/?l=linux-i2c&m=137235593101385&w=2
- https://lkml.org/lkml/2013/6/24/430
Let's use DMA mode even for small transfers.
Without this patch, i2c reads the incorrect sgtl5000 version on a mx28evk when
touchscreen is enabled:
[ 5.856270] sgtl5000 0-000a: Device with ID register 0 is not a sgtl5000
[ 9.877307] sgtl5000 0-000a: ASoC: failed to probe CODEC -19
[ 9.883528] mxs-sgtl5000 sound.12: ASoC: failed to instantiate card -19
[ 9.892955] mxs-sgtl5000 sound.12: snd_soc_register_card failed (-19)
Cc: <stable@vger.kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Marek Vasut <marex@denx.de>
[wsa: we have a proper solution for -next, so this non intrusive
solution is OK for now]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
Pull i2c updates from Wolfram Sang:
- new drivers: Kontron PLD, Wondermedia VT
- mv64xxx driver gained sun4i support and a bigger cleanup
- duplicate driver 'intel-mid' removed
- added generic device tree binding for sda holding time (and
designware driver already uses it)
- we tried to allow driver probing with only device tree and no i2c
ids, but I had to revert it because of side effects. Needs some
rethinking.
- driver bugfixes, cleanups...
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (34 commits)
i2c-designware: use div_u64 to fix link
i2c: Kontron PLD i2c bus driver
i2c: iop3xxx: fix build failure after waitqueue changes
i2c-designware: make SDA hold time configurable
i2c: mv64xxx: Set bus frequency to 100kHz if clock-frequency is not provided
i2c: imx: allow autoloading on dt ids
i2c: mv64xxx: Fix transfer error code
i2c: i801: SMBus patch for Intel Coleto Creek DeviceIDs
i2c: omap: correct usage of the interrupt enable register
i2c-pxa: prepare clock before use
Revert "i2c: core: make it possible to match a pure device tree driver"
i2c: nomadik: allocate adapter number dynamically
i2c: nomadik: support elder Nomadiks
i2c: mv64xxx: Add Allwinner sun4i compatible
i2c: mv64xxx: make the registers offset configurable
i2c: mv64xxx: Add macros to access parts of registers
i2c: vt8500: Add support for I2C bus on Wondermedia SoCs
i2c: designware: fix race between subsequent xfers
i2c: bfin-twi: Read and write the FIFO in loop
i2c: core: make it possible to match a pure device tree driver
...
Pull powerpc updates from Ben Herrenschmidt:
"This is the powerpc changes for the 3.11 merge window. In addition to
the usual bug fixes and small updates, the main highlights are:
- Support for transparent huge pages by Aneesh Kumar for 64-bit
server processors. This allows the use of 16M pages as transparent
huge pages on kernels compiled with a 64K base page size.
- Base VFIO support for KVM on power by Alexey Kardashevskiy
- Wiring up of our nvram to the pstore infrastructure, including
putting compressed oopses in there by Aruna Balakrishnaiah
- Move, rework and improve our "EEH" (basically PCI error handling
and recovery) infrastructure. It is no longer specific to pseries
but is now usable by the new "powernv" platform as well (no
hypervisor) by Gavin Shan.
- I fixed some bugs in our math-emu instruction decoding and made it
usable to emulate some optional FP instructions on processors with
hard FP that lack them (such as fsqrt on Freescale embedded
processors).
- Support for Power8 "Event Based Branch" facility by Michael
Ellerman. This facility allows what is basically "userspace
interrupts" for performance monitor events.
- A bunch of Transactional Memory vs. Signals bug fixes and HW
breakpoint/watchpoint fixes by Michael Neuling.
And more ... I appologize in advance if I've failed to highlight
something that somebody deemed worth it."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (156 commits)
pstore: Add hsize argument in write_buf call of pstore_ftrace_call
powerpc/fsl: add MPIC timer wakeup support
powerpc/mpic: create mpic subsystem object
powerpc/mpic: add global timer support
powerpc/mpic: add irq_set_wake support
powerpc/85xx: enable coreint for all the 64bit boards
powerpc/8xx: Erroneous double irq_eoi() on CPM IRQ in MPC8xx
powerpc/fsl: Enable CONFIG_E1000E in mpc85xx_smp_defconfig
powerpc/mpic: Add get_version API both for internal and external use
powerpc: Handle both new style and old style reserve maps
powerpc/hw_brk: Fix off by one error when validating DAWR region end
powerpc/pseries: Support compression of oops text via pstore
powerpc/pseries: Re-organise the oops compression code
pstore: Pass header size in the pstore write callback
powerpc/powernv: Fix iommu initialization again
powerpc/pseries: Inform the hypervisor we are using EBB regs
powerpc/perf: Add power8 EBB support
powerpc/perf: Core EBB support for 64-bit book3s
powerpc/perf: Drop MMCRA from thread_struct
powerpc/perf: Don't enable if we have zero events
...
PCI device hotplug
- Add pci_alloc_dev() interface (Gu Zheng)
- Add pci_bus_get()/put() for reference counting (Jiang Liu)
- Fix SR-IOV reference count issues (Jiang Liu)
- Remove unused acpi_pci_roots list (Jiang Liu)
MSI
- Conserve interrupt resources on x86 (Alexander Gordeev)
AER
- Force fatal severity when component has been reset (Betty Dall)
- Reset link below Root Port as well as Downstream Port (Betty Dall)
- Fix "Firmware first" flag setting (Bjorn Helgaas)
- Don't parse HEST for non-PCIe devices (Bjorn Helgaas)
ASPM
- Warn when we can't disable ASPM as driver requests (Bjorn Helgaas)
Miscellaneous
- Add CircuitCo PCI IDs (Darren Hart)
- Add AMD CZ SATA and SMBus PCI IDs (Shane Huang)
- Work around Ivytown NTB BAR size issue (Jon Mason)
- Detect invalid initial BAR values (Kevin Hao)
- Add pcibios_release_device() (Sebastian Ott)
- Fix powerpc & sparc PCI_UNKNOWN power state usage (Bjorn Helgaas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=X3Lo
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"PCI device hotplug
- Add pci_alloc_dev() interface (Gu Zheng)
- Add pci_bus_get()/put() for reference counting (Jiang Liu)
- Fix SR-IOV reference count issues (Jiang Liu)
- Remove unused acpi_pci_roots list (Jiang Liu)
MSI
- Conserve interrupt resources on x86 (Alexander Gordeev)
AER
- Force fatal severity when component has been reset (Betty Dall)
- Reset link below Root Port as well as Downstream Port (Betty Dall)
- Fix "Firmware first" flag setting (Bjorn Helgaas)
- Don't parse HEST for non-PCIe devices (Bjorn Helgaas)
ASPM
- Warn when we can't disable ASPM as driver requests (Bjorn Helgaas)
Miscellaneous
- Add CircuitCo PCI IDs (Darren Hart)
- Add AMD CZ SATA and SMBus PCI IDs (Shane Huang)
- Work around Ivytown NTB BAR size issue (Jon Mason)
- Detect invalid initial BAR values (Kevin Hao)
- Add pcibios_release_device() (Sebastian Ott)
- Fix powerpc & sparc PCI_UNKNOWN power state usage (Bjorn Helgaas)"
* tag 'pci-v3.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (51 commits)
MAINTAINERS: Add ACPI folks for ACPI-related things under drivers/pci
PCI: Add CircuitCo vendor ID and subsystem ID
PCI: Use pdev->pm_cap instead of pci_find_capability(..,PCI_CAP_ID_PM)
PCI: Return early on allocation failures to unindent mainline code
PCI: Simplify IOV implementation and fix reference count races
PCI: Drop redundant setting of bus->is_added in virtfn_add_bus()
unicore32/PCI: Remove redundant call of pci_bus_add_devices()
m68k/PCI: Remove redundant call of pci_bus_add_devices()
PCI / ACPI / PM: Use correct power state strings in messages
PCI: Fix comment typo for pcie_pme_remove()
PCI: Rename pci_release_bus_bridge_dev() to pci_release_host_bridge_dev()
PCI: Fix refcount issue in pci_create_root_bus() error recovery path
ia64/PCI: Clean up pci_scan_root_bus() usage
PCI/AER: Reset link for devices below Root Port or Downstream Port
ACPI / APEI: Force fatal AER severity when component has been reset
PCI/AER: Remove "extern" from function declarations
PCI/AER: Move AER severity defines to aer.h
PCI/AER: Set dev->__aer_firmware_first only for matching devices
PCI/AER: Factor out HEST device type matching
PCI/AER: Don't parse HEST table for non-PCIe devices
...
This fixes the following link error:
drivers/built-in.o: In function `dw_i2c_probe':
of_iommu.c:(.text+0x18c8f0): undefined reference to `__aeabi_uldivmod'
make: *** [vmlinux] Error 1
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Christian Ruppert <christian.ruppert@abilis.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- A large slew of improvements of the Genric pin configuration
support, and deployment in four different platforms:
Rockchip, Super-H PFC, ABx500 and TZ1090. Support BIAS_BUS_HOLD,
get device tree parsing and debugfs support into shape.
- We also have device tree support with generic naming conventions
for the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now
handled in the device core: "sleep" and "idle", removing a lot
of boilerplate code in drivers. We do not yet know if this is
the final word for pin PM, but it already make things a lot
easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where
several pins are managed by a single register, and augment it to
handle sleep modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=EbAf
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
- A large slew of improvements of the Genric pin configuration support,
and deployment in four different platforms: Rockchip, Super-H PFC,
ABx500 and TZ1090. Support BIAS_BUS_HOLD, get device tree parsing
and debugfs support into shape.
- We also have device tree support with generic naming conventions for
the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now handled in
the device core: "sleep" and "idle", removing a lot of boilerplate
code in drivers. We do not yet know if this is the final word for
pin PM, but it already make things a lot easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where several
pins are managed by a single register, and augment it to handle sleep
modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
* tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
pinctrl: vt8500: wmt: remove redundant dev_err call in wmt_pinctrl_probe()
pinctrl: remove bindings for pinconf options needing more thought
pinctrl: remove slew-rate parameter from tz1090
pinctrl: set unit for debounce time pinconfig to usec
pinctrl: more clarifications for generic pull configs
pinctrl: rip out the direct pinconf API
pinctrl-tz1090-pdc: add TZ1090 PDC pinctrl driver
pinctrl-tz1090: add TZ1090 pinctrl driver
pinctrl: samsung: Staticize drvdata_list
pinctrl: rockchip: Add missing irq_gc_unlock() call before return error
pinctrl: abx500: rework error path
pinctrl: abx500: suppress hardcoded value
pinctrl: abx500: factorize code
pinctrl: abx500: fix abx500_gpio_get()
pinctrl: abx500: fix abx500_pin_config_set()
pinctrl: abx500: Add device tree support
sh-pfc: Guard DT parsing with #ifdef CONFIG_OF
pinctrl: add Intel BayTrail GPIO/pinctrl support
pinctrl: fix pinconf_ops::pin_config_dbg_parse_modify kerneldoc
pinctrl: Staticize local symbols
...
Conflicts:
drivers/net/ethernet/ti/davinci_mdio.c
drivers/pinctrl/Makefile
These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in
this branch, both containing almost no platform specific code at all,
since they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part of
the SoC specific code. With the changes done by Thomas Petazzoni, we can
now more easily have PCI host controller drivers as loadable modules and
keep them separate from the platform code in drivers/pci/host. This has
already led to the discovery that three platforms (exynos, spear and imx)
are actually using an identical PCIe host controller and will be able
to share a driver once support for spear and imx is added.
Conflicts:
* asm/glue-proc.h has one CPU type getting added that conflicts
with another addition in 3.10-rc7
* Simple context changes in arch/arm/Makefile and arch/arm/Kconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=0r9S
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC specific changes from Arnd Bergmann:
"These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and
EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in this
branch, both containing almost no platform specific code at all, since
they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part
of the SoC specific code. With the changes done by Thomas Petazzoni,
we can now more easily have PCI host controller drivers as loadable
modules and keep them separate from the platform code in
drivers/pci/host. This has already led to the discovery that three
platforms (exynos, spear and imx) are actually using an identical PCIe
host controller and will be able to share a driver once support for
spear and imx is added."
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (480 commits)
ARM: integrator: let pciv3 use mem/premem from device tree
ARM: integrator: set local side PCI addresses right
ARM: dts: Add pcie controller node for exynos5440-ssdk5440
ARM: dts: Add pcie controller node for Samsung EXYNOS5440 SoC
ARM: EXYNOS: Enable PCIe support for Exynos5440
pci: Add PCIe driver for Samsung Exynos
ARM: OMAP5: voltagedomain data: remove temporary OMAP4 voltage data
ARM: keystone: Move CPU bringup code to dedicated asm file
ARM: multiplatform: always pick one CPU type
ARM: imx: select syscon for IMX6SL
ARM: keystone: select ARM_ERRATA_798181 only for SMP
ARM: imx: Synertronixx scb9328 needs to select SOC_IMX1
ARM: OMAP2+: AM43x: resolve SMP related build error
dmaengine: edma: enable build for AM33XX
ARM: edma: Add EDMA crossbar event mux support
ARM: edma: Add DT and runtime PM support to the private EDMA API
dmaengine: edma: Add TI EDMA device tree binding
arm: add basic support for Rockchip RK3066a boards
arm: add debug uarts for rockchip rk29xx and rk3xxx series
arm: Add basic clocks for Rockchip rk3066a SoCs
...
Add i2c support for the on-board PLD found on some Kontron embedded
modules.
Originally-From: Michael Brunner <michael.brunner@kontron.com>
Signed-off-by: Kevin Strasser <kevin.strasser@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There has long been a syntax problem in iop3xx_i2c_wait_event() which
has been somehow hidden by the macros in <linux/wait.h>. After some
recent cleanup/rework of the wait_event_* helpers, the bug has come
out from hiding and now results in build failure:
/work/kernel/next/drivers/i2c/busses/i2c-iop3xx.c: In function 'iop3xx_i2c_wait_event':
/work/kernel/next/drivers/i2c/busses/i2c-iop3xx.c:176:143: error: expected ')' before ';' token
/work/kernel/next/drivers/i2c/busses/i2c-iop3xx.c:176:157: error: expected ')' before ';' token
/work/kernel/next/drivers/i2c/busses/i2c-iop3xx.c:176:213: error: expected ')' before ';' token
/work/kernel/next/drivers/i2c/busses/i2c-iop3xx.c:176:291: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement]
/work/kernel/next/drivers/i2c/busses/i2c-iop3xx.c:176:551: error: expected ')' before ';' token
/work/kernel/next/drivers/i2c/busses/i2c-iop3xx.c:176:565: error: expected ')' before ';' token
/work/kernel/next/drivers/i2c/busses/i2c-iop3xx.c:176:764: error: expected ')' before ';' token
/work/kernel/next/drivers/i2c/busses/i2c-iop3xx.c:176:778: error: expected ')' b
Fix by removing stray ';'
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch makes the SDA hold time configurable through device tree.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Pierrick Hascoet <pierrick.hascoet@abilis.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com> for arch/arc bits
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case of collision on i2c bus the controller which lost bus mastership
stays as a slave for all subsequent transfers. This results in the i2c
controller never writing to the bus for future transactions, resulting
in i2c transfer timeouts.
This fix checks for a collision on last I2C transaction and sets the
I2COM_MASTER bit for the new transaction.
Signed-off-by: Sachin Surendran <sachin.surendran@alliedtelesis.co.nz>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This commit adds checking whether clock-frequency property acquisition
has succeeded. If not, the frequency is set to 100kHz by default.
The Device Tree binding documentation is updated accordingly.
Based on the intials patches from Zbigniew Bodek
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Zbigniew Bodek <zbb@semihalf.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow udev to autoload the module when booting with device-tree
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver returns -ENODEV as error code if it did not get an ACK
from the device. Per Documentation/i2c/fault-codes, it should
return -ENXIO.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds the i801 SMBus Controller DeviceIDs for the Intel Coleto Creek PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- Add devicetree support to timer, pinctrl (probe), I2C block,
watchdog, DMA controller and clocks.
- Piecewise add a device tree containing all peripherals.
- Delete the ATAG boot path.
- Delete redundant platform data and board files.
- Convert to multiplatform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=fstd
-----END PGP SIGNATURE-----
Merge tag 'u300-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/soc
From Linus Walleij:
Device Tree and Multiplatform support for U300:
- Add devicetree support to timer, pinctrl (probe), I2C block,
watchdog, DMA controller and clocks.
- Piecewise add a device tree containing all peripherals.
- Delete the ATAG boot path.
- Delete redundant platform data and board files.
- Convert to multiplatform.
* tag 'u300-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (40 commits)
ARM: u300: switch to using syscon regmap for board
ARM: u300: Update MMC configs for u300 defconfig
spi: pl022: use DMA by default when probing from DT
pinctrl: get rid of all platform data for coh901
ARM: u300: convert MMC/SD clock to device tree
ARM: u300: move the gated system controller clocks to DT
i2c: stu300: do not request a specific clock name
clk: move the U300 fixed and fixed-factor to DT
ARM: u300: remove register definition file
ARM: u300: add syscon node
ARM: u300 use module_spi_driver to register driver
ARM: u300: delete remnant machine headers
ARM: u300: convert to multiplatform
ARM: u300: localize <mach/u300-regs.h>
ARM: u300: delete <mach/irqs.h>
ARM: u300: delete <mach/hardware.h>
ARM: u300: push down syscon registers
ARM: u300: remove deps from debug macro
ARM: u300: move debugmacro to debug includes
ARM: u300: delete all static board data
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I got a build error today that made me realize that it is not
possible to build a kernel for a SiRF platform without enabling
CONFIG_PRIMA2, since a lot of common code depends on CONFIG_PRIMA2.
This fixes all occurences that appear like common SiRF code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
We've been lucky not to have any interrupts fire during the suspend
path, otherwise we would have unpredictable behaviour in the kernel.
Based on the logic of the kernel code interrupts from i2c should be
prohibited during suspend. Kernel writes 0 to the I2C_IE register in
the omap_i2c_runtime_suspend() function. In the other side kernel
writes saved interrupt flags to the I2C_IE register in
omap_i2c_runtime_resume() function. I.e. interrupts should be disabled
during suspend.
This works for chips with version1 registers scheme. Interrupts are
disabled during suspend. For chips with version2 scheme registers
writting 0 to the I2C_IE register does nothing (because now the
I2C_IRQENABLE_SET register is located at this address). This register
is used to enable interrupts. For disabling interrupts
I2C_IRQENABLE_CLR register should be used.
Because the registers I2C_IRQENABLE_SET and I2C_IE have the same
addresses, the interrupt enabling procedure is unchanged.
I've checked that interrupts in the i2c controller are still enabled
after writting 0 to the I2C_IRQENABLE_SET register. With this patch
interrupts are disabled in the omap_i2c_runtime_suspend() function.
Patch is based on:
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
tag: v3.10-rc2
Verified on OMAP4430.
Signed-off-by: Oleksandr Dmytryshyn <oleksandr.dmytryshyn@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On OLPC XO-1.75 (MMP2), a WARN_ON() was occurring during boot
since the clock being enabled by i2c-pxa had not been prepared.
Use clk_prepare_enable() to ensure that the prepare operation
has taken place, and use clk_disable_unprepare() in the matching
shutdown paths.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We have used the default clock associated with the block
for a long time, only heuristics in the clock system has
made this work anyway. This needs to be done away with as
we start probing this driver and its clocks exclusively
from the device tree.
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This utilize the new pinctrl core PM helpers to transition
the driver to "sleep" and "idle" states, cutting away some
boilerplate code.
Cc: Hebbar Gururaja <gururaja.hebbar@ti.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Nomadik I2C was using a local atomic counter to number
the I2C adapters. This does not work on configurations where
you also add, say a GPIO bit-banged adapter to the system.
They will start to conflict about being adapter 0.
There is no reason to use the numbered adapter function, and
the semantic effect on systems with only Nomadik I2C blocks
will be none - instead of increasing the number atomically
in the driver itself, it is done in the I2C core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Nomadik I2C block was introduced with the Nomadik STn8815
SoC (the STn8810 incidentally is identical to the one named
i2c-stu300.c). However as developments have only been tested
on the DB8500 family, it was not properly working with the
STn8815 anymore.
Rectify this by adding some vendor variant data in the same
manner as other PrimeCells, and switch code path depending
on version.
Tested on the S8815 Nomadik dongle.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add the compatible string for the Allwinner A10 i2c controller and the
associated register layout.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Allwinner i2c controller uses the same logic as the Marvell one, but
with slightly different register offsets.
Introduce a structure that will be passed by either the pdata or
associated to the compatible strings, and that holds the various
registers that might be needed.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
These macros make it more comprehensive to access to useful masked and
shifted area of the various registers used.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds support for the I2C bus controllers found on Wondermedia
8xxx-series SoCs. Only master-mode is supported.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
[wsa: fixed one macro to shift 8 instead of 16]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang