The GPU GX GDSC has GPU_GX_BCR reset and gfx3d_clk CXC, as stated
on downstream kernels (and as verified upstream, because otherwise
random lockups happen).
Also, add PWRSTS_RET and NO_RET_PERIPH: also as found downstream,
and also as verified here, to avoid GPU related lockups it is
necessary to force retain mem, but *not* peripheral when enabling
this GDSC (and, of course, the inverse on disablement).
With this change, the GPU finally works flawlessly on my four
different MSM8998 devices from two different manufacturers.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210114221059.483390-11-angelogioacchino.delregno@somainline.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In some rare occasions, we want to only set the RETAIN_MEM bit, but
not the RETAIN_PERIPH one: this is seen on at least SDM630/636/660's
GPU-GX GDSC, where unsetting and setting back the RETAIN_PERIPH bit
will generate chaos and panics during GPU suspend time (mainly, the
chaos is unaligned access).
For this reason, introduce a new NO_RET_PERIPH flag to the GDSC
driver to address this corner case.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210113183817.447866-8-angelogioacchino.delregno@somainline.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds a basic driver for the MPLL block found in MStar/SigmaStar
ARMv7 SoCs.
Currently this driver is only good for calculating the rates of it's
outputs and the actual configuration must be done before the kernel
boots. Usually this is done even before u-boot starts.
This driver targets the MPLL block found in the MSC313/MSC313E but
there is no documentation this chip so the register descriptions for
the another MStar chip the MST786 were used as they seem to match.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/r/20210211052206.2955988-5-daniel@0x0f.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a devm helper for clk_hw_register_fixed_factor() so that drivers that internally
register fixed factor clocks for things like dividers don't need to manually unregister
them on remove or if probe fails.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/r/20210211052206.2955988-4-daniel@0x0f.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
out the correct rate to use. This fixes displays running 4k@60Hz and
some other resolutions that haven't been exercised and fully understood
until now.
-----BEGIN PGP SIGNATURE-----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=jPmu
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One small fix for the Allwinner clk driver so that display clks figure
out the correct rate to use.
This fixes displays running 4k@60Hz and some other resolutions that
haven't been exercised and fully understood until now"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi-ng: mp: fix parent rate change flag check
Add support for Intel's eASIC N5X platform. The clock manager driver for
the N5X is very similar to the Agilex platform, we can re-use most of
the Agilex clock driver.
This patch makes the necessary changes for the driver to differentiate
between the Agilex and the N5X platforms.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20210212143059.478554-2-dinguyen@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The bd718x7 only needs a regmap from parent device. This can be
obtained by call to dev_get_regmap. Do not require parent to
populate the driver data for this.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20210105123028.GA3409663@localhost.localdomain
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Starting from A2, the A-PLL calculation has changed. Use the
existing formula for A0/A1 and the new formula for A2 onwards.
Fixes: d3d04f6c33 ("clk: Add support for AST2600 SoC")
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Link: https://lore.kernel.org/r/20210119061715.6043-1-ryan_chen@aspeedtech.com
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Recalling NVM data into RAM during probe() initiates a re-calibration of
the clock. If the clock is already in-use, the recall operation can cause
a glitch on the frequency out. At power on, the factory data are loaded
from NVM into RAM by default. If the clock frequency has been changed
since power on, the recall operation can be used to re-initialize the clock
to factory setting.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@xilinx.com>
Link: https://lore.kernel.org/r/1612496104-3437-3-git-send-email-saeed.nowshadi@xilinx.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There are two registers which can set the load capacitance for
XTAL1 and XTAL2. These are optional registers when using an
external crystal. Parse the device tree and set the
corresponding registers accordingly.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20210207185140.3653350-2-aford173@gmail.com
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/zynq/clkc.c: In function ‘zynq_clk_register_fclk’:
drivers/clk/zynq/clkc.c:106:14: warning: variable ‘clk’ set but not used [-Wunused-but-set-variable]
drivers/clk/zynq/clkc.c: In function ‘zynq_clk_register_periph_clk’:
drivers/clk/zynq/clkc.c:179:14: warning: variable ‘clk’ set but not used [-Wunused-but-set-variable]
drivers/clk/zynq/clkc.c: In function ‘zynq_clk_setup’:
drivers/clk/zynq/clkc.c:220:14: warning: variable ‘clk’ set but not used [-Wunused-but-set-variable]
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-21-lee.jones@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Also demote non-worthy header to standard comment block.
Fixes the following W=1 kernel build warning(s):
drivers/clk/versatile/clk-icst.c:53: warning: Function parameter or member 'map' not described in 'clk_icst'
drivers/clk/versatile/clk-icst.c:53: warning: Function parameter or member 'vcoreg_off' not described in 'clk_icst'
drivers/clk/versatile/clk-icst.c:53: warning: Function parameter or member 'lockreg_off' not described in 'clk_icst'
drivers/clk/versatile/clk-icst.c:435: warning: cannot understand function prototype: 'const struct icst_params icst525_apcp_cm_params = '
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-20-lee.jones@linaro.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/gate.c:67: warning: Function parameter or member 'hw' not described in 'omap36xx_gate_clk_enable_with_hsdiv_restore'
drivers/clk/ti/gate.c:67: warning: Excess function parameter 'clk' description in 'omap36xx_gate_clk_enable_with_hsdiv_restore'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-17-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/dpll.c:163: warning: Function parameter or member 'user' not described in '_register_dpll'
drivers/clk/ti/dpll.c:163: warning: Excess function parameter 'hw' description in '_register_dpll'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-16-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/clockdomain.c:107: warning: Function parameter or member 'hw' not described in 'omap2_init_clk_clkdm'
drivers/clk/ti/clockdomain.c:107: warning: Excess function parameter 'clk' description in 'omap2_init_clk_clkdm'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-14-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/st/clkgen-fsyn.c:186: warning: Function parameter or member 'data' not described in 'st_clk_quadfs_pll'
drivers/clk/st/clkgen-fsyn.c:466: warning: Function parameter or member 'regs_base' not described in 'st_clk_quadfs_fsynth'
drivers/clk/st/clkgen-fsyn.c:466: warning: Function parameter or member 'lock' not described in 'st_clk_quadfs_fsynth'
drivers/clk/st/clkgen-fsyn.c:466: warning: Function parameter or member 'data' not described in 'st_clk_quadfs_fsynth'
drivers/clk/st/clkgen-fsyn.c:466: warning: Function parameter or member 'chan' not described in 'st_clk_quadfs_fsynth'
drivers/clk/st/clkgen-fsyn.c:466: warning: Function parameter or member 'md' not described in 'st_clk_quadfs_fsynth'
drivers/clk/st/clkgen-fsyn.c:466: warning: Function parameter or member 'pe' not described in 'st_clk_quadfs_fsynth'
drivers/clk/st/clkgen-fsyn.c:466: warning: Function parameter or member 'sdiv' not described in 'st_clk_quadfs_fsynth'
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Stephen Gallimore <stephen.gallimore@st.com>
Cc: Pankaj Dev <pankaj.dev@st.com>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-13-lee.jones@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
And remove an incorrect entry.
Fixes the following W=1 kernel build warning(s):
drivers/clk/st/clkgen-pll.c:142: warning: cannot understand function prototype: 'struct clkgen_pll '
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Stephen Gallimore <stephen.gallimore@st.com>
Cc: Pankaj Dev <pankaj.dev@st.com>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-12-lee.jones@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Not much effort has been put into this one.
Demote it for the time being at least.
Fixes the following W=1 kernel build warning(s):
drivers/clk/mvebu/ap-cpu-clk.c:52: warning: Function parameter or member 'ratio_state_reg' not described in 'cpu_dfs_regs'
drivers/clk/mvebu/ap-cpu-clk.c:52: warning: Function parameter or member 'divider_mask' not described in 'cpu_dfs_regs'
drivers/clk/mvebu/ap-cpu-clk.c:52: warning: Function parameter or member 'cluster_offset' not described in 'cpu_dfs_regs'
drivers/clk/mvebu/ap-cpu-clk.c:52: warning: Function parameter or member 'force_mask' not described in 'cpu_dfs_regs'
drivers/clk/mvebu/ap-cpu-clk.c:52: warning: Function parameter or member 'divider_offset' not described in 'cpu_dfs_regs'
drivers/clk/mvebu/ap-cpu-clk.c:52: warning: Function parameter or member 'divider_ratio' not described in 'cpu_dfs_regs'
drivers/clk/mvebu/ap-cpu-clk.c:52: warning: Function parameter or member 'ratio_offset' not described in 'cpu_dfs_regs'
drivers/clk/mvebu/ap-cpu-clk.c:52: warning: Function parameter or member 'ratio_state_offset' not described in 'cpu_dfs_regs'
drivers/clk/mvebu/ap-cpu-clk.c:52: warning: Function parameter or member 'ratio_state_cluster_offset' not described in 'cpu_dfs_regs'
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Cc: Omri Itach <omrii@marvell.com>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-10-lee.jones@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/socfpga/clk-pll-a10.c: In function ‘__socfpga_pll_init’:
drivers/clk/socfpga/clk-pll-a10.c:76:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-9-lee.jones@linaro.org
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/socfpga/clk-pll.c: In function ‘__socfpga_pll_init’:
drivers/clk/socfpga/clk-pll.c:83:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-8-lee.jones@linaro.org
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/sifive/fu540-prci.h:16:35: warning: ‘prci_clk_fu540’ defined but not used [-Wunused-const-variable=]
drivers/clk/sifive/fu540-prci.h:16:35: warning: ‘prci_clk_fu540’ defined but not used [-Wunused-const-variable=]
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Pragnesh Patel <Pragnesh.patel@sifive.com>
Cc: Zong Li <zong.li@sifive.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-7-lee.jones@linaro.org
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/zynqmp/divider.c:46: warning: Function parameter or member 'max_div' not described in 'zynqmp_clk_divider'
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Rajan Vaja <rajan.vaja@xilinx.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-22-lee.jones@linaro.org
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/spear/spear1310_clock.c:385:13: warning: no previous prototype for ‘spear1310_clk_init’ [-Wmissing-prototypes]
drivers/clk/spear/spear1340_clock.c:442:13: warning: no previous prototype for ‘spear1340_clk_init’ [-Wmissing-prototypes]
Cc: Viresh Kumar <vireshk@kernel.org>
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-20-lee.jones@linaro.org
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/qcom/clk-rpm.c:453:29: warning: ‘clk_rpm_branch_ops’ defined but not used [-Wunused-const-variable=]
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-19-lee.jones@linaro.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/clk-xgene.c:229: warning: Function parameter or member 'mask' not described in 'xgene_clk_pmd'
drivers/clk/clk-xgene.c:229: warning: Function parameter or member 'flags' not described in 'xgene_clk_pmd'
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Loc Ho <lho@apm.com>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-18-lee.jones@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/qcom/mmcc-msm8974.c:85:27: warning: ‘mmcc_xo_mmpll0_1_2_gpll0’ defined but not used [-Wunused-const-variable=]
drivers/clk/qcom/mmcc-msm8974.c:77:32: warning: ‘mmcc_xo_mmpll0_1_2_gpll0_map’ defined but not used [-Wunused-const-variable=]
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-17-lee.jones@linaro.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/clk-npcm7xx.c:438:43: warning: ‘npcm7xx_gates’ defined but not used [-Wunused-const-variable=]
drivers/clk/clk-npcm7xx.c:365:48: warning: ‘npcm7xx_divs_fx’ defined but not used [-Wunused-const-variable=]
Cc: Avi Fishman <avifishman70@gmail.com>
Cc: Tomer Maimon <tmaimon77@gmail.com>
Cc: Tali Perry <tali.perry1@gmail.com>
Cc: Patrick Venture <venture@google.com>
Cc: Nancy Yuen <yuenn@google.com>
Cc: Benjamin Fair <benjaminfair@google.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Nuvoton Technologies <tali.perry@nuvoton.com>
Cc: openbmc@lists.ozlabs.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-16-lee.jones@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/clk-fixed-mmio.c:62: warning: Function parameter or member 'pdev' not described in 'of_fixed_mmio_clk_probe'
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Jan Kotas <jank@cadence.com>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-15-lee.jones@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/qcom/gcc-ipq4019.c: In function ‘clk_cpu_div_set_rate’:
drivers/clk/qcom/gcc-ipq4019.c:1279:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-14-lee.jones@linaro.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/dpll44xx.c:114: warning: Function parameter or member 'hw' not described in 'omap4_dpll_regm4xen_recalc'
drivers/clk/ti/dpll44xx.c:114: warning: Function parameter or member 'parent_rate' not described in 'omap4_dpll_regm4xen_recalc'
drivers/clk/ti/dpll44xx.c:114: warning: Excess function parameter 'clk' description in 'omap4_dpll_regm4xen_recalc'
drivers/clk/ti/dpll44xx.c:150: warning: Function parameter or member 'hw' not described in 'omap4_dpll_regm4xen_round_rate'
drivers/clk/ti/dpll44xx.c:150: warning: Function parameter or member 'parent_rate' not described in 'omap4_dpll_regm4xen_round_rate'
drivers/clk/ti/dpll44xx.c:150: warning: Excess function parameter 'clk' description in 'omap4_dpll_regm4xen_round_rate'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-11-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/tegra/cvb.c:106: warning: Function parameter or member 'align' not described in 'tegra_cvb_add_opp_table'
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-10-lee.jones@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/tegra/clk-tegra30.c: In function ‘tegra30_enable_cpu_clock’:
drivers/clk/tegra/clk-tegra30.c:1107:15: warning: variable ‘reg’ set but not used [-Wunused-but-set-variable]
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-8-lee.jones@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/qcom/clk-regmap.c:97: warning: Function parameter or member 'dev' not described in 'devm_clk_register_regmap'
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-5-lee.jones@linaro.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/dpll3xxx.c:414: warning: Function parameter or member 'hw' not described in 'omap3_dpll_recalc'
drivers/clk/ti/dpll3xxx.c:414: warning: Function parameter or member 'parent_rate' not described in 'omap3_dpll_recalc'
drivers/clk/ti/dpll3xxx.c:414: warning: Excess function parameter 'clk' description in 'omap3_dpll_recalc'
drivers/clk/ti/dpll3xxx.c:437: warning: Function parameter or member 'hw' not described in 'omap3_noncore_dpll_enable'
drivers/clk/ti/dpll3xxx.c:437: warning: Excess function parameter 'clk' description in 'omap3_noncore_dpll_enable'
drivers/clk/ti/dpll3xxx.c:479: warning: Function parameter or member 'hw' not described in 'omap3_noncore_dpll_disable'
drivers/clk/ti/dpll3xxx.c:479: warning: Excess function parameter 'clk' description in 'omap3_noncore_dpll_disable'
drivers/clk/ti/dpll3xxx.c:755: warning: Function parameter or member 'hw' not described in 'omap3_clkoutx2_recalc'
drivers/clk/ti/dpll3xxx.c:755: warning: Function parameter or member 'parent_rate' not described in 'omap3_clkoutx2_recalc'
drivers/clk/ti/dpll3xxx.c:755: warning: Excess function parameter 'clk' description in 'omap3_clkoutx2_recalc'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-4-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/clkt_dpll.c:284: warning: Function parameter or member 'hw' not described in 'omap2_dpll_round_rate'
drivers/clk/ti/clkt_dpll.c:284: warning: Function parameter or member 'parent_rate' not described in 'omap2_dpll_round_rate'
drivers/clk/ti/clkt_dpll.c:284: warning: Excess function parameter 'clk' description in 'omap2_dpll_round_rate'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-3-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/zynq/pll.c:187: warning: Function parameter or member 'name' not described in 'clk_register_zynq_pll'
drivers/clk/zynq/pll.c:187: warning: Function parameter or member 'parent' not described in 'clk_register_zynq_pll'
drivers/clk/zynq/pll.c:187: warning: Function parameter or member 'pll_ctrl' not described in 'clk_register_zynq_pll'
drivers/clk/zynq/pll.c:187: warning: Function parameter or member 'pll_status' not described in 'clk_register_zynq_pll'
drivers/clk/zynq/pll.c:187: warning: Function parameter or member 'lock_index' not described in 'clk_register_zynq_pll'
drivers/clk/zynq/pll.c:187: warning: Function parameter or member 'lock' not described in 'clk_register_zynq_pll'
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-2-lee.jones@linaro.org
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
These are all "early clocks" that require initialization just at
of_clk_init() time. Use CLK_OF_DECLARE() to declare them.
This also fixes a problem that was spotted when fw_devlink was
set to 'on' by default: the boards failed to boot. The reason is
that CLK_OF_DECLARE_DRIVER() clears the OF_POPULATED and causes
the consumers of the clock to be postponed by fw_devlink until
the second initialization routine of the clock has been completed.
One of the consumers of the clock is the timer, which is used as a
clocksource, and needs the clock initialized early. Postponing the
timers caused the fail at boot.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210203154332.470587-1-tudor.ambarus@microchip.com
Acked-by: Saravana Kannan <saravanak@google.com>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This allows fw_devlink to recognize clock provider drivers that don't
use the device-driver model to initialize the device. fw_devlink will
use this information to make sure consumers of such clock providers
aren't indefinitely blocked from probing, waiting for the power domain
device to appear and bind to a driver.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210205222644.2357303-9-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On AXG platforms HHI_MIPI_CNTL0 is part of the MIPI/PCIe analog PHY
region and is not related to clock one and can be removed from it.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The mux clocks don't always correctly take the new parent into account
when the parent is updated while the clock is disabled. Set the update
bit when enabling the clock to force an update of the mux.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20210125170819.26130-3-laurent.pinchart@ideasonboard.com
Reviewed-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
If MT8183 SoC support is enabled, almost all machines will use topckgen,
apmixedsys, infracfg, mcucfg and subsystem clocks, so it feels wrong to
require each one to select that symbols manually.
Instead, enable it whenever COMMON_CLK_MT8183_* is disabled as
a simplification. This would add few KB in the kernel image size but
will make the life a bit easier to the users, anyway you'll need to probably
enable all of them if you want to have proper support for that SoC.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210203105423.682960-1-enric.balletbo@collabora.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The ST-Ericsson U300 platform is getting removed, so this driver is no
longer needed.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210120131026.1721788-5-arnd@kernel.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The CSR SiRF prima2/atlas platforms are getting removed, so this driver
is no longer needed.
Cc: Barry Song <baohua@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210120131026.1721788-4-arnd@kernel.org
Acked-by: Barry Song <baohua@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The zte zx platform is getting removed, so this driver is no
longer needed.
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210120131026.1721788-3-arnd@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The tango platform is getting removed, so the driver is no
longer needed.
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Mans Rullgard <mans@mansr.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210120131026.1721788-2-arnd@kernel.org
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The xlnx_vcu driver is actually a clock controller driver which provides
clocks that can be used by a driver for the encoder/decoder units. There
is no reason to keep this driver in soc. Move the driver to clk.
NOTE: The register mapping actually contains registers for AXI
performance monitoring, but these are not used by the driver.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20210121071659.1226489-16-m.tretter@pengutronix.de
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
If a driver registers a divider clock with a parent_hw instead of the
parent_name, the parent_hw is ignored and the clock does not have a
parent.
Fix this by initializing the parents the same way they are initialized
for clock gates.
Fixes: ff25881713 ("clk: divider: Add support for specifying parents via DT/pointers")
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20210121071659.1226489-3-m.tretter@pengutronix.de
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For ZynqMP (Ultrascale) the PFD and VCO limits are different. In order to
support these, this change adds a compatible string (i.e.
'adi,zynqmp-axi-clkgen-2.00.a') which will take into account for these
limits and apply them.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Mathias Tausen <mta@gomspace.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210201151245.21845-3-alexandru.ardelean@analog.com
Acked-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The intent is to be able to run this driver to access the IP core in setups
where FPGA board is also connected via a PCIe bus. In such cases the number
of combinations explodes, where the host system can be an x86 with Xilinx
Zynq/ZynqMP/Microblaze board connected via PCIe.
Or even a ZynqMP board with a ZynqMP/Zynq/Microblaze connected via PCIe.
To accommodate for these cases, this change removes the limitation for this
driver to be compilable only on Zynq/Microblaze architectures.
And adds dependencies on the mechanisms required by the driver to work (OF
and HAS_IOMEM).
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210201151245.21845-2-alexandru.ardelean@analog.com
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This GDSC enables (or cuts!) power to the Multimedia Subsystem IOMMU
(mmss smmu), which has bootloader pre-set secure contexts.
In the event of a complete power loss, the secure contexts will be
reset and the hypervisor will crash the SoC.
To prevent this, and get a working multimedia subsystem, set this
GDSC as always on.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210114221059.483390-10-angelogioacchino.delregno@somainline.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Hardware clock gating is supported on some of the clocks declared in
there: ignoring that it does exist may lead to unstabilities on some
firmwares.
Add the HWCG registers where applicable to stop potential crashes.
This was verified on a smartphone shipped with a recent MSM8998
firmware, which will experience random crashes without this change.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210114221059.483390-9-angelogioacchino.delregno@somainline.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
All of the GPLLs in the MSM8998 Global Clock Controller are Fabia PLLs
and not generic alphas: this was producing bad effects over the entire
clock tree of MSM8998, where any GPLL child clock was declaring a false
clock rate, due to their parent also showing the same.
The issue resides in the calculation of the clock rate for the specific
Alpha PLL type, where Fabia has a different register layout; switching
the MSM8998 GPLLs to the correct Alpha Fabia PLL type fixes the rate
(calculation) reading. While at it, also make these PLLs fixed since
their rate is supposed to *never* be changed while the system runs, as
this would surely crash the entire SoC.
Now all the children of all the PLLs are also complying with their
specified clock table and system stability is improved.
Fixes: b5f5f525c5 ("clk: qcom: Add MSM8998 Global Clock Control (GCC) driver")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210114221059.483390-7-angelogioacchino.delregno@somainline.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The GPU IOMMU depends on this clock and the hypervisor will crash
the SoC if this clock gets disabled because the secure contexts
that have been set on this IOMMU by the bootloader will become
unaccessible (or they get reset).
Mark this clock as critical to avoid this issue when the Adreno
GPU is enabled.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210114221059.483390-6-angelogioacchino.delregno@somainline.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This patch adds the missing video_cc_mvs0_clk entry to
videocc-sm8250 replicating in upstream the explicit entry for this clock in
downstream.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210204150120.1521959-4-bryan.odonoghue@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This patch adds the missing video_cc_mvs0_div_clk_src entry to
videocc-sm8250 replicating in upstream the explicit entry for this clock in
downstream.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210204150120.1521959-3-bryan.odonoghue@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds Global Clock controller (GCC) driver for SM8350 SoC
Signed-off-by: Vivek Aknurwar <viveka@codeaurora.org>
Signed-off-by: Jeevan Shriram <jshriram@codeaurora.org>
[vkoul: rebase and tidy up for upstream]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210127070811.152690-6-vkoul@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Lucid 5LPE is a slightly different Lucid PLL with different offsets and
porgramming sequence so add support for these
Signed-off-by: Vivek Aknurwar <viveka@codeaurora.org>
Signed-off-by: Jeevan Shriram <jshriram@codeaurora.org>
[vkoul: rebase and tidy up for upstream]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210127070811.152690-4-vkoul@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Trion 5LPE set rate uses code similar to alpha_pll_trion_set_rate() but
with different registers. Modularize these by moving out latch and latch
ack bits so that we can reuse the function.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210127070811.152690-3-vkoul@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Driver uses regval variable for holding register values, replace with a
shorter one val
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210127070811.152690-2-vkoul@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add clocks, resets and some of the GDSC provided by the global clock
controller found in the Qualcomm SC8180x platform.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210126043155.1847823-2-bjorn.andersson@linaro.org
[sboyd@kernel.org: Drop F macro as it's already defined]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There are intermittent GDSC power-up failures observed for titan top
gdsc, which requires the XO clock. Thus mark all the MM XO clocks always
enabled from probe.
Fixes: 8d4025943e ("clk: qcom: camcc-sc7180: Use runtime PM ops instead of clk ones")
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/1611128871-5898-1-git-send-email-tdas@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For some reason global GFM_MASK ended up with bit 1 instead of bit 0.
Remove the global GFM_MASK and reuse mux_mask field.
Fixes: a2d8f50780 ("clk: qcom: Add support to LPASS AUDIO_CC Glitch Free Mux clocks")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210119113851.18946-1-srinivas.kandagatla@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a driver for the SDX55 APCS clock controller. It is part of the APCS
hardware block, which among other things implements also a combined mux
and half integer divider functionality. The APCS clock controller has 3
parent clocks:
1. Board XO
2. Fixed rate GPLL0
3. A7 PLL
This is required for enabling CPU frequency scaling on SDX55-based
platforms.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210118041156.50016-6-manivannan.sadhasivam@linaro.org
[sboyd@kernel.org: Fix unused ret in probe by hardcoding it]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for PLL found in Qualcomm SDX55 platforms which is used to
provide clock to the Cortex A7 CPU via a mux. This PLL can provide high
frequency clock to the CPU above 1GHz as compared to the other sources
like GPLL0.
In this driver, the power domain is attached to the cpudev. This is
required for CPUFreq functionality and there seems to be no better place
to do other than this driver (no dedicated CPUFreq driver).
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210118041156.50016-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/imx/clk-imx6sl.c:156:6: warning: no previous prototype for ‘imx6sl_set_wait_clk’ [-Wmissing-prototypes]
Cc: Russell King <linux@armlinux.org.uk>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Ahmad Fatoum <a.fatoum@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
clkout1 and clkout2 allow to supply clocks from the SoC to the board,
which is used by some board designs to provide reference clocks.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
clkout1 and clkout2 allow to supply clocks from the SoC to the board,
which is used by some board designs to provide reference clocks.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PLL monitor is mentioned as a debug feature in the reference manual,
but there are some boards that use this clock output as a reference clock
for board level components. Add support for those clocks in the clock
driver, so this clock output can be used properly.
Note that the VIDEO1, GPU and VPU mux inputs are rotated compared to the
description in the reference manual. The order in this patch has been
empirically validated.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/imx/clk-imx31.c:54:28: warning: ‘uart_clks’ defined but not used [-Wunused-const-variable=]
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since 5d283b0838 ("clk: imx6: Fix procedure to switch the parent
of LDB_DI_CLK"), the clock driver warns if ldb_di\d_sel is changed
from reset value on system boot. This warning is printed even if
the bootloader (or a previous kernel that did kexec) followed the
correct procedure for glitch-free reparenting.
As such systems are doing everything correctly, a warning is too
harsh. Demote to a notice, so users are still alerted, but without
cluttering a loglevel=5 boot.
While at it, add the words "possible glitch" into the log message, to
make it more user-friendly.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Build fix for CONFIG_PM=n in the mmp2 driver
- Kconfig warning for unmet dependencies in the i.MX driver
- Make the camera AHB clk always be enabled on qcom sc7180
- Use rate round down semantics for qcom sm8250 SD clks
-----BEGIN PGP SIGNATURE-----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=wIlb
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A handful of clk driver fixes:
- Build fix for CONFIG_PM=n in the mmp2 driver
- Kconfig warning for unmet dependencies in the i.MX driver
- Make the camera AHB clk always be enabled on qcom sc7180
- Use rate round down semantics for qcom sm8250 SD clks"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: mmp2: fix build without CONFIG_PM
clk: qcom: gcc-sm250: Use floor ops for sdcc clks
clk: imx: fix Kconfig warning for i.MX SCU clk
clk: qcom: gcc-sc7180: Mark the camera abh clock always ON
While the clocks are fairly similar to the H6, many differ in tiny
details, so a separate clock driver seems indicated.
Derived from the H6 clock driver, and adjusted according to the manual.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210127172500.13356-4-andre.przywara@arm.com
The clocks itself are identical to the H6 R-CCU, it's just that the H616
has not all of them implemented (or connected).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210127172500.13356-3-andre.przywara@arm.com
Fixes the following W=1 kernel build warning(s):
drivers/clk/renesas/renesas-cpg-mssr.c:168: warning: Function parameter or member 'smstpcr_saved' not described in 'cpg_mssr_priv'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-12-lee.jones@linaro.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The clock API splits its interface into sleepable ant atomic contexts:
- clk_prepare/clk_unprepare for stuff that might sleep
- clk_enable_clk_disable for anything that may be done in atomic context
The code handling runtime PM for clocks only calls clk_disable() on
suspend requests, and clk_enable on resume requests. This means that
runtime PM with clock providers that only have the prepare/unprepare
methods implemented is basically useless.
Many clock implementations can't accommodate atomic contexts. This is
often the case when communication with the clock happens through another
subsystem like I2C or SCMI.
Let's make the clock PM code useful with such clocks by safely invoking
clk_prepare/clk_unprepare upon resume/suspend requests. Of course, when
such clocks are registered with the PM layer then pm_runtime_irq_safe()
can't be used, and neither pm_runtime_suspend() nor pm_runtime_resume()
may be invoked in atomic context.
For clocks that do implement the enable and disable methods then
everything just works as before.
A note on sparse:
According to https://lwn.net/Articles/109066/ there are things
that sparse can't cope with. In particular, pm_clk_op_lock() and
pm_clk_op_unlock() may or may not lock/unlock psd->lock depending on
some runtime condition. To work around that we tell it the lock is
always untaken for the purpose of static analisys.
Thanks to Naresh Kamboju for reporting issues with the initial patch.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fixes the following W=1 kernel build warning(s):
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'name' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'parent_names' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'num_parents' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'base' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'muxdiv_offset' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'mux_shift' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'mux_width' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'mux_flags' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'div_shift' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'div_width' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'div_flags' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'gate_offset' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'gate_shift' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'gate_flags' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'flags' not described in 'rockchip_clk_register_halfdiv'
drivers/clk/rockchip/clk-half-divider.c:168: warning: Function parameter or member 'lock' not described in 'rockchip_clk_register_halfdiv'
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-5-lee.jones@linaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Fixes the following W=1 kernel build warning(s):
drivers/clk/rockchip/clk-pll.c:104: warning: Function parameter or member 'i' not described in 'RK3036_PLLCON'
drivers/clk/rockchip/clk-pll.c:365: warning: Function parameter or member 'nr' not described in 'RK3066_PLL_RESET_DELAY'
drivers/clk/rockchip/clk-pll.c:584: warning: Function parameter or member 'i' not described in 'RK3399_PLLCON'
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Xing Zheng <zhengxing@rock-chips.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-4-lee.jones@linaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Fixes the following W=1 kernel build warning(s):
drivers/clk/rockchip/clk-cpu.c:65: warning: Function parameter or member 'cpu_mux' not described in 'rockchip_cpuclk'
drivers/clk/rockchip/clk-cpu.c:65: warning: Function parameter or member 'cpu_mux_ops' not described in 'rockchip_cpuclk'
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-3-lee.jones@linaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Fixes the following W=1 kernel build warning(s):
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'name' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'parent_names' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'num_parents' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'base' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'muxdiv_offset' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'mux_shift' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'mux_width' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'mux_flags' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'div_offset' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'div_shift' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'div_width' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'div_flags' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'div_table' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'gate_offset' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'gate_shift' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'gate_flags' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'flags' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:45: warning: Function parameter or member 'lock' not described in 'rockchip_clk_register_branch'
drivers/clk/rockchip/clk.c:180: warning: Function parameter or member 'hw' not described in 'rockchip_fractional_approximation'
drivers/clk/rockchip/clk.c:180: warning: Function parameter or member 'rate' not described in 'rockchip_fractional_approximation'
drivers/clk/rockchip/clk.c:180: warning: Function parameter or member 'parent_rate' not described in 'rockchip_fractional_approximation'
drivers/clk/rockchip/clk.c:180: warning: Function parameter or member 'm' not described in 'rockchip_fractional_approximation'
drivers/clk/rockchip/clk.c:180: warning: Function parameter or member 'n' not described in 'rockchip_fractional_approximation'
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Xing Zheng <zhengxing@rock-chips.com>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-2-lee.jones@linaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
While comparing clocks between the H6 and H616, some of the M factor
ranges were found to be wrong: the manual says they are only covering
two bits [1:0], but our code had "5" in the number-of-bits field.
By writing 0xff into that register in U-Boot and via FEL, it could be
confirmed that bits [4:2] are indeed masked off, so the manual is right.
Change to number of bits in the affected clock's description.
Fixes: 524353ea48 ("clk: sunxi-ng: add support for the Allwinner H6 CCU")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210118000912.28116-1-andre.przywara@arm.com
Fixes the following W=1 kernel build warning(s):
drivers/clk/sunxi/clk-mod0.c:24: warning: Function parameter or member 'req' not described in 'sun4i_a10_get_mod0_factors'
Cc: "Emilio López" <emilio@elopez.com.ar>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210120093040.1719407-19-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/clk/sunxi/clk-sunxi.c:34: warning: Function parameter or member 'req' not described in 'sun4i_get_pll1_factors'
drivers/clk/sunxi/clk-sunxi.c:81: warning: Function parameter or member 'req' not described in 'sun6i_a31_get_pll1_factors'
drivers/clk/sunxi/clk-sunxi.c:158: warning: Function parameter or member 'req' not described in 'sun8i_a23_get_pll1_factors'
drivers/clk/sunxi/clk-sunxi.c:202: warning: Function parameter or member 'req' not described in 'sun4i_get_pll5_factors'
drivers/clk/sunxi/clk-sunxi.c:229: warning: Function parameter or member 'req' not described in 'sun6i_a31_get_pll6_factors'
drivers/clk/sunxi/clk-sunxi.c:250: warning: Function parameter or member 'req' not described in 'sun5i_a13_get_ahb_factors'
drivers/clk/sunxi/clk-sunxi.c:289: warning: Function parameter or member 'req' not described in 'sun6i_get_ahb1_factors'
drivers/clk/sunxi/clk-sunxi.c:328: warning: Function parameter or member 'req' not described in 'sun6i_ahb1_recalc'
drivers/clk/sunxi/clk-sunxi.c:346: warning: Function parameter or member 'req' not described in 'sun4i_get_apb1_factors'
drivers/clk/sunxi/clk-sunxi.c:385: warning: Function parameter or member 'req' not described in 'sun7i_a20_get_out_factors'
drivers/clk/sunxi/clk-sunxi.c:415: warning: cannot understand function prototype: 'const struct clk_factors_config sun4i_pll1_config = '
drivers/clk/sunxi/clk-sunxi.c:724: warning: cannot understand function prototype: 'struct div_data '
drivers/clk/sunxi/clk-sunxi.c:945: warning: Function parameter or member 'node' not described in 'sunxi_divs_clk_setup'
drivers/clk/sunxi/clk-sunxi.c:945: warning: Function parameter or member 'data' not described in 'sunxi_divs_clk_setup'
Cc: "Emilio López" <emilio@elopez.com.ar>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210120093040.1719407-15-lee.jones@linaro.org
pm_clk_suspend()/pm_clk_resume() are defined as NULL pointers rather than
empty inline stubs without CONFIG_PM:
drivers/clk/mmp/clk-audio.c:402:16: error: called object type 'void *' is not a function or function pointer
pm_clk_suspend(dev);
drivers/clk/mmp/clk-audio.c:411:15: error: called object type 'void *' is not a function or function pointer
pm_clk_resume(dev);
I tried redefining the helper functions, but that caused additional
problems. This is the simple solution of replacing the __maybe_unused
trick with an #ifdef.
Fixes: 725262d291 ("clk: mmp2: Add audio clock controller driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210103135503.3668784-1-arnd@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Followup to the commits 5e4b7e82d4 ("clk: qcom: gcc-sdm845: Use floor
ops for sdcc clks") and 6d37a8d192 ("clk: qcom: gcc-sc7180: Use floor ops
for sdcc clks"). Use floor ops for sdcc clocks on sm8250.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 3e5770921a ("clk: qcom: gcc: Add global clock controller driver for SM8250")
Link: https://lore.kernel.org/r/20210109013314.3443134-1-dmitry.baryshkov@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
A previous patch introduced a harmless randconfig warning:
WARNING: unmet direct dependencies detected for MXC_CLK_SCU
Depends on [n]: COMMON_CLK [=y] && ARCH_MXC [=n] && IMX_SCU [=y] && HAVE_ARM_SMCCC [=y]
Selected by [m]:
- CLK_IMX8QXP [=m] && COMMON_CLK [=y] && (ARCH_MXC [=n] && ARM64 [=y] || COMPILE_TEST [=y]) && IMX_SCU [=y] && HAVE_ARM_SMCCC [=y]
Since the symbol is now hidden and only selected by other symbols,
just remove the dependencies and require the other drivers to
get it right.
Fixes: 6247e31b75 ("clk: imx: scu: fix MXC_CLK_SCU module build break")
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201230155244.981757-1-arnd@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The camera clock controller requires the AHB clock, the driver when
moved to use the pm_runtime_get() API, the camera ahb clock failed turn
on before access, thus mark it as always ON.
Reported-by: Stephen Boyd <sboyd@kernel.org>
Fixes: 8d4025943e ("clk: qcom: camcc-sc7180: Use runtime PM ops instead of clk ones")
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/1608573816-1465-1-git-send-email-tdas@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Current implementation defaults the hda clocks to clk_m. This causes hda
to run too slow to operate correctly. Fix this by defaulting to pll_p and
setting the frequency to the correct rate.
This matches upstream t124 and downstream t30.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Ion Agorria <ion@agorria.com>
Acked-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20210108135913.2421585-2-pgwipeout@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
R-Car V3U has a CPG different enough to not be a generic Gen3 CPG but
similar enough to reuse code. Introduce a new CPG library, factor out
the SD clock handling and hook it to the generic Gen3 CPG driver so we
have an equal state. V3U will make use of it in the next patch then.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20201227174202.40834-4-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
We want to reuse SD clock handling for other SoCs and, thus, need to
generalize it. So, don't access cpg_quirks in that realm.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20201227174202.40834-3-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the module clocks used by the Pin Function Controller (PFC) and
General Purpose Input/Output (GPIO) blocks, and their parent clock CP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20201019120614.22149-4-geert+renesas@glider.be
According to Figure 8.1.1 ("Block Diagram of CPG (R-Car V3U-AD)") in the
R-Car V3U Series User's Manual Rev. 0.5, the parent of the CBFUSA clock
is EXTAL.
Fixes: 17bcc8035d ("clk: renesas: cpg-mssr: Add support for R-Car V3U")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20201019120614.22149-3-geert+renesas@glider.be
The S2 internal core clock does not exist on R-Car V3U. Remove it.
Fixes: 17bcc8035d ("clk: renesas: cpg-mssr: Add support for R-Car V3U")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20201019120614.22149-2-geert+renesas@glider.be
The CEC clock on the H6 SoC is a bit special, since it uses a fixed
pre-dividier for one source clock (the PLL), but conveys the other clock
(32K OSC) directly.
We are using a fixed predivider array for that, but fail to use the right
flag to actually activate that.
Fixes: 524353ea48 ("clk: sunxi-ng: add support for the Allwinner H6 CCU")
Reported-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210106143246.11255-1-andre.przywara@arm.com
While no information about the H6 RSB controller is included in the
datasheet or manual, the vendor BSP and power management blob both
reference the RSB clock parent and register address. These values were
verified by experimentation.
Since this clock/reset are added late, the specifier is added at the end
to maintain the existing DT binding. The code is kept in register order.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add modularization support to the Tegra124 EMC driver, which now can be
compiled as a loadable kernel module.
Note that EMC clock must be registered at clk-init time, otherwise PLLM
will be disabled as unused clock at boot time if EMC driver is compiled
as a module. Hence add a prepare/complete callbacks. similarly to what is
done for the Tegra20/30 EMC drivers.
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201228154920.18846-2-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch corrects display clocks for i.MX8qxp DC0 subsystem by
calling imx_clk_scu2() to register them, instead of calling
imx_clk_scu(). The reason is that the clocks can source from
various parents. The clock source selection is controlled by
Distributed Slave System Controller(DSC). According to the DSC spec,
the below table describes the generic source selections for clocks
with the same type in various subsystems. And, the display controller
subsystem spec says the display clocks can source from PLL1, PLL2 or
bypass clock, thus we may specify the correct parents for imx_clk_scu2().
The bypass clock's parent is determined by the SCU firmware.
Currently, the parent is 'pixel_link_clk_in' from HW point of view.
To be more specific, the parent is dummy for i.MX8qxp DC0, while
HDMI TX PHY PLL for i.MX8qm DC0. In practice, the display clocks
source from the bypass clock only when driving i.MX8qm HDMI TX.
So, for the both display clocks, we simply specify 'dc0_bypass0_clk'
bypass clock as a valid parent.
-----------------------------------------
| src_sel[28:26] | |
-----------------------------------------
| 0x0 | xtal24M |
| 0x1 | PLL0 |
| 0x2 | PLL1 |
| 0x3 | PLL2 |
| 0x4 | bypass reference clock |
| 0x5 to 0x7 | reserved |
-----------------------------------------
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The XTAL clock is provided via .dts since Linux 5.6. Remove
compatibility code for .dtbs which are older than that.
The switch to the HHI syscon has been done with Linux 5.1. Also remove
any code needed to support .dtbs that have not switched to the HHI
syscon yet.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201221183624.932649-2-martin.blumenstingl@googlemail.com
Popagate the error code from meson_clk_pll_set_rate() when the PLL does
not lock with the new settings.
Fixes: 722825dcd5 ("clk: meson: migrate plls clocks to clk_regmap")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201226121556.975418-4-martin.blumenstingl@googlemail.com
The error codes returned by meson_clk_get_pll_settings() are all
negative. Make "ret" a signed integer in meson_clk_pll_set_rate() to
make it match with the clk_ops.set_rate API as well as the data type
returned by meson_clk_get_pll_settings().
Fixes: 8eed1db1ad ("clk: meson: pll: update driver for the g12a")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201226121556.975418-3-martin.blumenstingl@googlemail.com
The "rate" parameter in meson_clk_pll_set_rate() contains the new rate.
Retrieve the old rate with clk_hw_get_rate() so we don't inifinitely try
to switch from the new rate to the same rate again.
Fixes: 7a29a86943 ("clk: meson: Add support for Meson clock controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201226121556.975418-2-martin.blumenstingl@googlemail.com
ability to get struct clk pointers from a struct clk_hw so that clk providers
can consume the clks they provide, if they need to do something like that. This
has been a long missing part of the clk provider API that will help us move
away from exposing a struct clk pointer in the struct clk_hw. Tracepoints are
added for the clk_set_rate() "range" functions, similar to the tracepoints we
already have for clk_set_rate() and we added a column to debugfs to help
developers understand the hardware enable state of clks in case firmware or
bootloader state is different than what is expected. Overall the core changes
are mostly improving the clk driver writing experience.
At the driver level, we have the usual collection of driver updates and new
drivers for new SoCs. This time around the Qualcomm folks introduced a good
handful of clk drivers for various parts of three or four SoCs. The SiFive
folks added a new clk driver for their FU740 SoCs, coming in second on the
diffstat and then Atmel AT91 and Amlogic SoCs had lots of work done after that
for various new features. One last thing to note in the driver area is that the
i.MX driver has gained a new binding to support SCU clks after being on the
list for many months. It uses a two cell binding which is sort of rare in clk
DT bindings. Beyond that we have the usual set of driver fixes and tweaks that
come from more testing and finding out that some configuration was wrong or
that a driver could support being built as a module.
Core:
- Add some trace points for clk_set_rate() "range" functions
- Add hardware enable information to clk_summary debugfs
- Replace clk-provider.h with of_clk.h when possible
- Add devm variant of clk_notifier_register()
- Add clk_hw_get_clk() to generate a struct clk from a struct clk_hw
New Drivers:
- Bindings for Canaan K210 SoC clks
- Support for SiFive FU740 PRCI
- Camera clks on Qualcomm SC7180 SoCs
- GCC and RPMh clks on Qualcomm SDX55 SoCs
- RPMh clks on Qualcomm SM8350 SoCs
- LPASS clks on Qualcomm SM8250 SoCs
Updates:
- DVFS support for AT91 clk driver
- Update git repo branch for Renesas clock drivers
- Add camera (CSI) and video-in (VIN) clocks on Renesas R-Car V3U
- Add RPC (QSPI/HyperFLASH) clocks on Renesas RZ/G2M, RZ/G2N, and RZ/G2E
- Stop using __raw_*() I/O accessors in Renesas clk drivers
- One more conversion of DT bindings to json-schema
- Make i.MX clk-gate2 driver more flexible
- New two cell binding for i.MX SCU clks
- Drop of_match_ptr() in i.MX8 clk drivers
- Add arch dependencies for Rockchip clk drivers
- Fix i2s on Rockchip rk3066
- Add MIPI DSI clks on Amlogic axg and g12 SoCs
- Support modular builds of Amlogic clk drivers
- Fix an Amlogic Video PLL clock dependency
- Samsung Kconfig dependencies updates for better compile test coverage
- Refactoring of the Samsung PLL clocks driver
- Small Tegra driver cleanups
- Minor fixes to Ingenic and VC5 clk drivers
- Cleanup patches to remove unused variables and plug memory leaks
-----BEGIN PGP SIGNATURE-----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=Wt9O
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The core framework got some nice improvements this time around. We
gained the ability to get struct clk pointers from a struct clk_hw so
that clk providers can consume the clks they provide, if they need to
do something like that. This has been a long missing part of the clk
provider API that will help us move away from exposing a struct clk
pointer in the struct clk_hw. Tracepoints are added for the
clk_set_rate() "range" functions, similar to the tracepoints we
already have for clk_set_rate() and we added a column to debugfs to
help developers understand the hardware enable state of clks in case
firmware or bootloader state is different than what is expected.
Overall the core changes are mostly improving the clk driver writing
experience.
At the driver level, we have the usual collection of driver updates
and new drivers for new SoCs. This time around the Qualcomm folks
introduced a good handful of clk drivers for various parts of three or
four SoCs. The SiFive folks added a new clk driver for their FU740
SoCs, coming in second on the diffstat and then Atmel AT91 and Amlogic
SoCs had lots of work done after that for various new features. One
last thing to note in the driver area is that the i.MX driver has
gained a new binding to support SCU clks after being on the list for
many months. It uses a two cell binding which is sort of rare in clk
DT bindings. Beyond that we have the usual set of driver fixes and
tweaks that come from more testing and finding out that some
configuration was wrong or that a driver could support being built as
a module.
Summary:
Core:
- Add some trace points for clk_set_rate() "range" functions
- Add hardware enable information to clk_summary debugfs
- Replace clk-provider.h with of_clk.h when possible
- Add devm variant of clk_notifier_register()
- Add clk_hw_get_clk() to generate a struct clk from a struct clk_hw
New Drivers:
- Bindings for Canaan K210 SoC clks
- Support for SiFive FU740 PRCI
- Camera clks on Qualcomm SC7180 SoCs
- GCC and RPMh clks on Qualcomm SDX55 SoCs
- RPMh clks on Qualcomm SM8350 SoCs
- LPASS clks on Qualcomm SM8250 SoCs
Updates:
- DVFS support for AT91 clk driver
- Update git repo branch for Renesas clock drivers
- Add camera (CSI) and video-in (VIN) clocks on Renesas R-Car V3U
- Add RPC (QSPI/HyperFLASH) clocks on Renesas RZ/G2M, RZ/G2N, and RZ/G2E
- Stop using __raw_*() I/O accessors in Renesas clk drivers
- One more conversion of DT bindings to json-schema
- Make i.MX clk-gate2 driver more flexible
- New two cell binding for i.MX SCU clks
- Drop of_match_ptr() in i.MX8 clk drivers
- Add arch dependencies for Rockchip clk drivers
- Fix i2s on Rockchip rk3066
- Add MIPI DSI clks on Amlogic axg and g12 SoCs
- Support modular builds of Amlogic clk drivers
- Fix an Amlogic Video PLL clock dependency
- Samsung Kconfig dependencies updates for better compile test coverage
- Refactoring of the Samsung PLL clocks driver
- Small Tegra driver cleanups
- Minor fixes to Ingenic and VC5 clk drivers
- Cleanup patches to remove unused variables and plug memory leaks"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (134 commits)
dt-binding: clock: Document canaan,k210-clk bindings
dt-bindings: Add Canaan vendor prefix
clk: vc5: Use "idt,voltage-microvolt" instead of "idt,voltage-microvolts"
clk: ingenic: Fix divider calculation with div tables
clk: sunxi-ng: Make sure divider tables have sentinel
clk: s2mps11: Fix a resource leak in error handling paths in the probe function
clk: mvebu: a3700: fix the XTAL MODE pin to MPP1_9
clk: si5351: Wait for bit clear after PLL reset
clk: at91: sam9x60: remove atmel,osc-bypass support
clk: at91: sama7g5: register cpu clock
clk: at91: clk-master: re-factor master clock
clk: at91: sama7g5: do not allow cpu pll to go higher than 1GHz
clk: at91: sama7g5: decrease lower limit for MCK0 rate
clk: at91: sama7g5: remove mck0 from parent list of other clocks
clk: at91: clk-sam9x60-pll: allow runtime changes for pll
clk: at91: sama7g5: add 5th divisor for mck0 layout and characteristics
clk: at91: clk-master: add 5th divisor for mck master
clk: at91: sama7g5: allow SYS and CPU PLLs to be exported and referenced in DT
dt-bindings: clock: at91: add sama7g5 pll defines
clk: at91: sama7g5: fix compilation error
...
- Bindings for Canaan K210 SoC clks
* clk-ingenic:
clk: ingenic: Fix divider calculation with div tables
* clk-vc5:
clk: vc5: Use "idt,voltage-microvolt" instead of "idt,voltage-microvolts"
* clk-cleanup:
clk: sunxi-ng: Make sure divider tables have sentinel
clk: s2mps11: Fix a resource leak in error handling paths in the probe function
clk: bcm: dvp: Add MODULE_DEVICE_TABLE()
clk: bcm: dvp: drop a variable that is assigned to only
* clk-canaan:
dt-binding: clock: Document canaan,k210-clk bindings
dt-bindings: Add Canaan vendor prefix
* clk-marvell:
clk: mvebu: a3700: fix the XTAL MODE pin to MPP1_9
- Add some trace points for clk_set_rate() "range" functions
- DVFS support for AT91 clk driver
* clk-ti:
clk: ti: omap5: Fix reboot DPLL lock failure when using ABE TIMERs
clk: ti: Fix memleak in ti_fapll_synth_setup
* clk-analog:
clk: axi-clkgen: move the OF table at the bottom of the file
clk: axi-clkgen: wrap limits in a struct and keep copy on the state object
dt-bindings: clock: adi,axi-clkgen: convert old binding to yaml format
* clk-trace:
clk: Trace clk_set_rate() "range" functions
* clk-at91:
clk: at91: sam9x60: remove atmel,osc-bypass support
clk: at91: sama7g5: register cpu clock
clk: at91: clk-master: re-factor master clock
clk: at91: sama7g5: do not allow cpu pll to go higher than 1GHz
clk: at91: sama7g5: decrease lower limit for MCK0 rate
clk: at91: sama7g5: remove mck0 from parent list of other clocks
clk: at91: clk-sam9x60-pll: allow runtime changes for pll
clk: at91: sama7g5: add 5th divisor for mck0 layout and characteristics
clk: at91: clk-master: add 5th divisor for mck master
clk: at91: sama7g5: allow SYS and CPU PLLs to be exported and referenced in DT
dt-bindings: clock: at91: add sama7g5 pll defines
clk: at91: sama7g5: fix compilation error
* clk-silabs:
clk: si5351: Wait for bit clear after PLL reset
- Support for SiFive FU740 PRCI
- Add hardware enable information to clk_summary debugfs
* clk-tegra:
clk: tegra: Fix duplicated SE clock entry
clk: tegra: bpmp: Clamp clock rates on requests
clk: tegra: Do not return 0 on failure
* clk-imx: (24 commits)
clk: imx: scu: remove the calling of device_is_bound
clk: imx: scu: Make pd_np with static keyword
clk: imx8mq: drop of_match_ptr from of_device_id table
clk: imx8mp: drop of_match_ptr from of_device_id table
clk: imx8mn: drop of_match_ptr from of_device_id table
clk: imx8mm: drop of_match_ptr from of_device_id table
clk: imx: gate2: Remove unused variable ret
clk: imx: gate2: Add locking in is_enabled op
clk: imx: gate2: Add cgr_mask for more flexible number of control bits
clk: imx: gate2: Check if clock is enabled against cgr_val
clk: imx: gate2: Keep the register writing in on place
clk: imx: gate2: Remove the IMX_CLK_GATE2_SINGLE_BIT special case
clk: imx: scu: fix build break when compiled as modules
clk: imx: remove redundant assignment to pointer np
clk: imx: remove unneeded semicolon
clk: imx: lpcg: add suspend/resume support
clk: imx: clk-imx8qxp-lpcg: add runtime pm support
clk: imx: lpcg: allow lpcg clk to take device pointer
clk: imx: imx8qxp-lpcg: add parsing clocks from device tree
clk: imx: scu: add suspend/resume support
...
* clk-sifive:
clk: sifive: Add clock enable and disable ops
clk: sifive: Fix the wrong bit field shift
clk: sifive: Add a driver for the SiFive FU740 PRCI IP block
clk: sifive: Use common name for prci configuration
clk: sifive: Extract prci core to common base
dt-bindings: fu740: prci: add YAML documentation for the FU740 PRCI
* clk-mediatek:
clk: mediatek: Make mtk_clk_register_mux() a static function
* clk-summary:
clk: Add hardware-enable column to clk summary
Commit 45c940184b ("dt-bindings: clk: versaclock5: convert to
yaml") accidentally changed "idt,voltage-microvolts" to
"idt,voltage-microvolt" in the DT bindings, while the driver still used
the former.
Update the driver to match the bindings, as
Documentation/devicetree/bindings/property-units.txt actually recommends
using "microvolt".
Fixes: 260249f929 ("clk: vc5: Enable addition output configurations of the Versaclock")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201218125253.3815567-1-geert+renesas@glider.be
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The previous code assumed that a higher hardware value always resulted
in a bigger divider, which is correct for the regular clocks, but is
an invalid assumption when a divider table is provided for the clock.
Perfect example of this is the PLL0_HALF clock, which applies a /2
divider with the hardware value 0, and a /1 divider otherwise.
Fixes: a9fa2893fc ("clk: ingenic: Add support for divider tables")
Cc: <stable@vger.kernel.org> # 5.2
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20201212135733.38050-1-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Two clock divider tables are missing sentinel at the end. Effect of that
is that clock framework reads past the last entry. Fix that with adding
sentinel at the end.
Issue was discovered with KASan.
Fixes: 0577e4853b ("clk: sunxi-ng: Add H3 clocks")
Fixes: c6a0637460 ("clk: sunxi-ng: Add A64 clocks")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201202203817.438713-1-jernej.skrabec@siol.net
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some resource should be released in the error handling path of the probe
function, as already done in the remove function.
The remove function was fixed in commit bf416bd457 ("clk: s2mps11: Add
missing of_node_put and of_clk_del_provider")
Fixes: 7cc560dea4 ("clk: s2mps11: Add support for s2mps11")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201212122818.86195-1-christophe.jaillet@wanadoo.fr
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is an error in the current code that the XTAL MODE
pin was set to NB MPP1_31 which should be NB MPP1_9.
The latch register of NB MPP1_9 has different offset of 0x8.
Signed-off-by: Terry Zhou <bjzhou@marvell.com>
[pali: Fix pin name in commit message]
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 7ea8250406 ("clk: mvebu: Add the xtal clock for Armada 3700 SoC")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201106100039.11385-1-pali@kernel.org
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Documentation states that SI5351_PLL_RESET_B and SI5351_PLL_RESET_A bits
are self clearing bits, so wait until they are cleared before
continuing.
This fixes a case when the clock doesn't come up properly after a PLL
reset. It worked properly when the frequency was below 900MHz, but with
900MHz it only works when we are waiting for the bit to clear.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20201130091033.1687-1-s.hauer@pengutronix.de
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Register CPU clock as being the master clock prescaler. This would
be used by DVFS. The block schema of SAMA7G5's PMC contains also a divider
between master clock prescaler and CPU (PMC_CPU_RATIO.RATIO) but the
frequencies supported by SAMA7G5 could be directly received from
CPUPLL + master clock prescaler and the extra divider would do no work in
case it would be enabled.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-12-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Re-factor master clock driver by splitting it into 2 clocks: prescaller
and divider clocks. Based on registered clock flags the prescaler's rate
could be changed at runtime. This is necessary for platforms supporting
DVFS (e.g. SAMA7G5) where master clock could be changed at run-time.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-11-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Since CPU PLL feeds both CPU clock and MCK0, MCK0 cannot go higher
than 200MHz and MCK0 maximum prescaller is 5 limit the CPU PLL at
1GHz to avoid MCK0 overclocking while CPU PLL is changed by DVFS.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-10-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On SAMA7G5 CPU clock is changed at run-time by DVFS. Since MCK0 and
CPU clock shares the same parent clock (CPUPLL clock) the MCK0 is
also changed by DVFS to avoid over/under clocking of MCK0 consumers.
The lower limit is changed to be able to set MCK0 accordingly by
DVFS.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-9-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
MCK0 is changed at runtime by DVFS. Due to this, since not all IPs
are glitch free aware at MCK0 changes, remove MCK0 from parent list
of other clocks (e.g. generic clock, programmable/system clock, MCKX).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-8-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This SoC has the 5th divisor for the mck0 master clock.
Adapt the characteristics accordingly.
Reported-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-6-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
clk-master can have 5 divisors with a field width of 3 bits
on some products.
Change the mask and number of divisors accordingly.
Reported-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-5-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Allow SYSPLL and CPUPLL to be referenced as a PMC_TYPE_CORE clock
from phandle in DT.
Suggested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[claudiu.beznea@microchip.com: adapt commit message, add CPU PLL]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-4-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add SAMA7G5 specific PLL defines to be referenced in a phandle as a
PMC_TYPE_CORE clock.
Suggested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[claudiu.beznea@microchip.com: adapt comit message, adapt sama7g5.c]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-3-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
pmc_data_allocate() has been changed. pmc_data_free() was removed.
Adapt the code taking this into consideration. With this the programmable
clocks were also saved in sama7g5_pmc so that they could be later
referenced.
Fixes: cb783bbbcf ("clk: at91: sama7g5: add clock support for sama7g5")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-2-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add MODULE_DEVICE_TABLE() so as to be able to use the driver as a
module. More precisely, for the driver to be loaded automatically at
boot.
Fixes: 1bc9597271 ("clk: bcm: Add BCM2711 DVP driver")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20201202103518.21889-1-nsaenzjulienne@suse.de
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The third parameter to devm_platform_get_and_ioremap_resource() is used
only to provide the used resource. As this variable isn't used
afterwards, switch to the function devm_platform_ioremap_resource()
which doesn't provide this output parameter.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20201120132121.2678997-1-u.kleine-koenig@pengutronix.de
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The clk_set_rate "range" functions don't have any tracepoints even
though it might be useful. Add some.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201207105050.2096917-1-maxime@cerno.tech
[sboyd@kernel.org: Reword commit text]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The change is mostly cosmetic. No functional changes.
Since the driver now uses of_device_get_match_data() to obtain some driver
specific info, there is no need to define the OF table before the probe
function.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201203074037.26940-2-alexandru.ardelean@analog.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Up until the these limits were global/hard-coded, since they are typically
limits of the fabric.
However, since this is an FPGA generated clock, this may run on setups
where one clock is on a fabric, and another one synthesized on another
fabric connected via PCIe (or some other inter-connect, and then these
limits need to be adjusted for each instance of the AXI CLKGEN.
This change wraps the current constants in 'axi_clkgen_limits' struct and
the 'axi_clkgen' instance keeps a copy of these limits, which is
initialized at probe from the default limits.
The limits are stored on the device-tree OF table, so that we can adjust
them via the compatible string.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201203074037.26940-1-alexandru.ardelean@analog.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Having the ABE DPLL ref and bypass muxes set to different inputs was
causing the DPLL not to lock when TIMER8 was used, as it is in the Pyra
for the backlight.
This patch fixes this by setting abe_dpll_bypass_clk_mux to sys_32k_ck
in omap5xxx_dt_clk_init.
A similar patch may also be needed for OMAP44xx which has similar code
in omap4xxx_dt_clk_init, but I have not added this as I have no hardware
to test on.
Signed-off-by: David Shah <dave@ds0.me>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/1d3abe2512054866cc2ea7b2592238f4fa06502a.1607253531.git.hns@goldelico.com
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
If clk_register fails, we should goto free branch
before function returns to prevent memleak.
Fixes: 163152cbbe ("clk: ti: Add support for FAPLL on dm816x")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201113131623.2098222-1-zhangqilong3@huawei.com
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add "hardware enable" column to the clk summary in order to show actual
hardware enable-state of all clocks. The possible states are "Y/N/?",
where question mark means that state is unknown, i.e. clock isn't a
mux and clk-driver doesn't support is_enabled() callback for this clock.
In conjunction with clk_ignore_unused, this tells us what unused clocks
are left enabled after bootloader. This is also a useful aid for
debugging interactions with firmware which changes clock states without
notifying kernel.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201115203432.13934-1-digetx@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
These are additional updates for the power domain support on OMAP,
moving to an implementation based on device tree information instead of
SoC specific code. This is the latest step in the ongoing process for
moving code out of arch/arm/mach-omap2.
I kept this separate from the other driver changes since it touches
code in multiple areas.
There is one conflict in the dra7.dts file, which adds another node
in a different branch. Watch out for adding the trailing '};'
both times.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=0mXx
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-omap-genpd-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC OMAP GenPD updates from Arnd Bergmann:
"These are additional updates for the power domain support on OMAP,
moving to an implementation based on device tree information instead
of SoC specific code. This is the latest step in the ongoing process
for moving code out of arch/arm/mach-omap2.
I kept this separate from the other driver changes since it touches
code in multiple areas"
* tag 'arm-soc-omap-genpd-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (51 commits)
ARM: OMAP2+: Fix am4 only build after genpd changes
ARM: dts: Configure power domain for omap5 dss
ARM: dts: omap5: add remaining PRM instances
soc: ti: omap-prm: omap5: add genpd support for remaining PRM instances
ARM: OMAP2+: Drop legacy platform data for dra7 gpmc
ARM: dts: Configure interconnect target module for dra7 iva
ARM: dts: dra7: add remaining PRM instances
soc: ti: omap-prm: dra7: add genpd support for remaining PRM instances
clk: ti: dra7: Drop idlest polling from IVA clkctrl clocks
ARM: OMAP2+: Drop legacy platform data for omap4 gpmc
ARM: OMAP2+: Drop legacy platform data for omap4 iva
ARM: dts: Configure power domain for omap4 dsp
ARM: dts: Configure power domain for omap4 dss
ARM: dts: omap4: add remaining PRM instances
soc: ti: omap-prm: omap4: add genpd support for remaining PRM instances
clk: ti: omap4: Drop idlest polling from IVA clkctrl clocks
ARM: OMAP2+: Drop legacy remaining legacy platform data for am4
ARM: dts: Use simple-pm-bus for genpd for am4 l3
ARM: dts: Move am4 l3 noc to a separate node
ARM: dts: Use simple-pm-bus for genpd for am4 l4_per
...
There are a couple of subsystems maintained by other people that
merge their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control
and SoC identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660
and SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs.
There is a trivial conflict in the cedrus driver, with two branches
adding the same CEDRUS_CAPABILITY_H265_DEC flag, and another trivial
remove/remove conflict in linux/dma-mapping.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=BjJf
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are a couple of subsystems maintained by other people that merge
their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power
domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control and SoC
identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660 and
SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs"
* tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (222 commits)
soc: mediatek: mmsys: Specify HAS_IOMEM dependency for MTK_MMSYS
firmware: xilinx: Properly align function parameter
firmware: xilinx: Add a blank line after function declaration
firmware: xilinx: Remove additional newline
firmware: xilinx: Fix kernel-doc warnings
firmware: xlnx-zynqmp: fix compilation warning
soc: xilinx: vcu: add missing register NUM_CORE
soc: xilinx: vcu: use vcu-settings syscon registers
dt-bindings: soc: xlnx: extract xlnx, vcu-settings to separate binding
soc: xilinx: vcu: drop useless success message
clk: samsung: mark PM functions as __maybe_unused
soc: samsung: exynos-chipid: initialize later - with arch_initcall
soc: samsung: exynos-chipid: order list of SoCs by name
memory: jz4780_nemc: Fix potential NULL dereference in jz4780_nemc_probe()
memory: ti-emif-sram: only build for ARMv7
memory: tegra30: Support interconnect framework
memory: tegra20: Support hardware versioning and clean up OPP table initialization
dt-bindings: memory: tegra20-emc: Document opp-supported-hw property
soc: rockchip: io-domain: Fix error return code in rockchip_iodomain_probe()
reset-controller: ti: force the write operation when assert or deassert
...
Add new functions "sifive_prci_clock_enable(), sifive_prci_clock_disable()
and sifive_clk_is_enabled()" to enable or disable the PRCI clock
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Tested-by: Zong Li <zong.li@sifive.com>
Link: https://lore.kernel.org/r/20201209094916.17383-6-zong.li@sifive.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add driver code for the SiFive FU740 PRCI IP block. This IP block
handles reset and clock control for the SiFive FU740 device and
implements SoC-level clock tree controls and dividers.
The link of unmatched as follow, and the U740-C000 manual would
be present in the same page as soon.
https://www.sifive.com/boards/hifive-unmatched
This driver contains bug fixes and contributions from
Henry Styles <hes@sifive.com>
Erik Danie <erik.danie@sifive.com>
Pragnesh Patel <pragnesh.patel@sifive.com>
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Pragnesh Patel <Pragnesh.patel@sifive.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Cc: Henry Styles <hes@sifive.com>
Cc: Erik Danie <erik.danie@sifive.com>
Cc: Pragnesh Patel <pragnesh.patel@sifive.com>
Link: https://lore.kernel.org/r/20201209094916.17383-4-zong.li@sifive.com
[sboyd@kernel.org: Include header to silence sparse]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use generic name CLK_SIFIVE_PRCI instead of CLK_SIFIVE_FU540_PRCI. This
patch is prepared for fu740 support.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Pragnesh Patel <Pragnesh.patel@sifive.com>
Link: https://lore.kernel.org/r/20201209094916.17383-3-zong.li@sifive.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Extract common core of prci driver to an independent file, it could
allow other chips to reuse it. Separate SoCs-dependent code 'fu540'
from prci core, then we can easily add 'fu740' later.
Almost these changes are code movement. The different is adding the
private data for each SoC use, so it needs to get match data in probe
callback function, then use the data for initialization.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Pragnesh Patel <Pragnesh.patel@sifive.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Link: https://lore.kernel.org/r/20201209094916.17383-2-zong.li@sifive.com
[sboyd@kernel.org: Include header to silence sparse]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from
the frequency table as the current frequency and clean up that
driver (Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle
driver (Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables
in DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it
to take the interconnect and OPP information from DT and clean it
up ((Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print
driver flags for devices with debug enabled (Alex Shi, Patrice
Chotard, Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan).
-----BEGIN PGP SIGNATURE-----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=BVdX
-----END PGP SIGNATURE-----
Merge tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update cpufreq (core and drivers), cpuidle (polling state
implementation and the PSCI driver), the OPP (operating performance
points) framework, devfreq (core and drivers), the power capping RAPL
(Running Average Power Limit) driver, the Energy Model support, the
generic power domains (genpd) framework, the ACPI device power
management, the core system-wide suspend code and power management
utilities.
Specifics:
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from the
frequency table as the current frequency and clean up that driver
(Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle driver
(Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables in
DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it to
take the interconnect and OPP information from DT and clean it up
(Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print driver
flags for devices with debug enabled (Alex Shi, Patrice Chotard,
Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan)"
* tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (86 commits)
cpufreq: Fix cpufreq_online() return value on errors
cpufreq: Fix up several kerneldoc comments
cpufreq: stats: Use local_clock() instead of jiffies
cpufreq: schedutil: Simplify sugov_update_next_freq()
cpufreq: intel_pstate: Simplify intel_cpufreq_update_pstate()
PM: domains: create debugfs nodes when adding power domains
opp: of: Allow empty opp-table with opp-shared
dt-bindings: opp: Allow empty OPP tables
media: venus: dev_pm_opp_put_*() accepts NULL argument
drm/panfrost: dev_pm_opp_put_*() accepts NULL argument
drm/lima: dev_pm_opp_put_*() accepts NULL argument
PM / devfreq: exynos: dev_pm_opp_put_*() accepts NULL argument
cpufreq: qcom-cpufreq-nvmem: dev_pm_opp_put_*() accepts NULL argument
cpufreq: dt: dev_pm_opp_put_regulators() accepts NULL argument
opp: Allow dev_pm_opp_put_*() APIs to accept NULL opp_table
opp: Don't create an OPP table from dev_pm_opp_get_opp_table()
cpufreq: dt: Don't (ab)use dev_pm_opp_get_opp_table() to create OPP table
opp: Reduce the size of critical section in _opp_kref_release()
PM / EM: Micro optimization in em_cpu_energy
cpufreq: arm_scmi: Discover the power scale in performance protocol
...
Detailed description for this pull request:
1. Update devfreq core
- Add new devfreq_frequency tracepoint to show the frequency change
information.
- Add governor feature flag. The devfreq governor is able to
have the specific flag in order to contain the non-common feature.
For example, if governor contains the 'immutable' feature, don't allow
user to change the governor via sysfs.
- Add governor sysfs attribute flag for each sysfs file. Prior to that
devfreq subsystem show the all sysfs files regardless of governor type.
But, some sysfs fils are not supported on the specific devfreq governor.
In order to show the only supported sysfs files according to the governor,
clarify the access permission of sysfs attributes according to governor.
When adding the devfreq governor, can specify the available attribute
information by using DEVFREQ_GOV_ATTR_* constant variable. The user can
read or write the sysfs attributes in accordance to the specified attributes.
- Clean-up the code to remove the duplicate code for the devfreq tracepoint
and to remove redundant governor_name field from struct devfreq
2. Update exynos-bus.c devfreq driver
- Add interconnect API support for the Samsung Exynos Bus Frequency driver
of exynos-bus.c. Complementing the devfreq driver with an interconnect
functionality allows to ensure the QoS requirements of devices accessing
the system memory (e.g. video processing devices) are fulfilled
and allows to avoid issues like the DMA underrun.
3. Update tegra devfreq driver
- Add interconnect support and OPP interface for tegra30-devfreq.c.
Also, it is to guarantee the QoS requirement of some devices like
display controller.
- Move tegra20-devfreq.c from drivers/devfreq/ into driver/memory/tegra/
in order to use the more proper monitoring feature such as EMC_STAT
which is based in driver/memory/tegra/.
- Separate the configuration information for different SoC on
tegra30-devfrqe.c. The tegra30-devfreq.c had been supported both
tegra30-actmon and tegra124-actmon devices. In order to use
the more correct configuration data, separate them.
- Use dev_err_probe() to handle the deferred probe error on tegra30-devfreq.c.
4. Pull the request of 'Tegra SoC and clock controller changes for v5.11'
sent by Krzysztof Kozlowski <krzk@kernel.org> in order to prevent the
build error.
-----BEGIN PGP SIGNATURE-----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=t1gj
-----END PGP SIGNATURE-----
Merge tag 'devfreq-next-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux
Pull devfreq updates for 5.11 from Chanwoo Choi:
1. Update devfreq core
- Add new devfreq_frequency tracepoint to show the frequency change
information.
- Add governor feature flag. The devfreq governor is able to set the
specific flag in order to support a non-common feature. For
example, if the governor supports the 'immutable' feature, don't
allow user space to change the governor via sysfs.
- Add governor sysfs attribute flag for each sysfs file. Prior to that
the devfreq subsystem allowed all of the sysfs files to be accessed
regardless of the governor type. But some sysfs fils are not
supported by specific devfreq governors. In order to only allow the
sysfs files supported by the governor to be accessed, clarify the
access permissions of sysfs attributes according to the governor.
When adding the devfreq governor, specify the available attribute
information by using DEVFREQ_GOV_ATTR_* symbols. The user can read
or write the sysfs attributes in accordance to the specified
access permissions.
- Clean-up the code to reduce duplication for the devfreq tracepoint
and to remove redundant governor_name field from struct devfreq.
2. Update exynos-bus.c devfreq driver
- Add interconnect API support to the Samsung Exynos Bus Frequency
driver, exynos-bus.c. Complementing the devfreq driver with
interconnect functionality allows to ensure that the QoS
requirements regarding devices accessing the system memory (e.g.
video processing devices) will be met and allows to avoid issues
like DMA underrun.
3. Update tegra devfreq driver
- Add interconnect support and OPP interface to tegra30-devfreq.c.
Also, it is to guarantee the QoS requirement of some devices like
the display controller.
- Move tegra20-devfreq.c from drivers/devfreq/ into drivers/memory/tegra/
in order to use the more proper monitoring feature such as EMC_STAT
which is located in drivers/memory/tegra/.
- Separate the configuration information for different SoCs in
tegra30-devfrqe.c. The tegra30-devfreq.c had been supporting both
tegra30-actmon and tegra124-actmon devices. In order to use the
more correct configuration data, separate them.
- Use dev_err_probe() to handle the deferred probe error in
tegra30-devfreq.c.
4. Pull the request of 'Tegra SoC and clock controller changes for
v5.11' sent by Krzysztof Kozlowski <krzk@kernel.org> in order to
avoid a build error."
* tag 'devfreq-next-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux:
PM / devfreq: tegra30: Separate configurations per-SoC generation
PM / devfreq: tegra30: Support interconnect and OPPs from device-tree
PM / devfreq: tegra20: Deprecate in a favor of emc-stat based driver
PM / devfreq: exynos-bus: Add registration of interconnect child device
dt-bindings: devfreq: Add documentation for the interconnect properties
soc/tegra: fuse: Add stub for tegra_sku_info
soc/tegra: fuse: Export tegra_read_ram_code()
clk: tegra: Export Tegra20 EMC kernel symbols
PM / devfreq: tegra30: Silence deferred probe error
PM / devfreq: tegra20: Relax Kconfig dependency
PM / devfreq: tegra20: Silence deferred probe error
PM / devfreq: Remove redundant governor_name from struct devfreq
PM / devfreq: Add governor attribute flag for specifc sysfs nodes
PM / devfreq: Add governor feature flag
PM / devfreq: Add tracepoint for frequency changes
PM / devfreq: Unify frequency change to devfreq_update_target func
trace: events: devfreq: Use fixed indentation size to improve readability
The periph_clks[] array contains duplicated entry for Security Engine
clock which was meant to be defined for T210, but it wasn't added
properly. This patch corrects the T210 SE entry and fixes the following
error message on T114/T124: "Tegra clk 127: register failed with -17".
Fixes: dc37fec483 ("clk: tegra: periph: Add new periph clks and muxes for Tegra210")
Tested-by Nicolas Chauvet <kwizart@gmail.com>
Reported-by Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201025224212.7790-1-digetx@gmail.com
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds the RPMH clocks present in SM8350 SoC
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201208064702.3654324-3-vkoul@kernel.org
[sboyd@kernel.org: Move sdx55 to the right place]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
50 MHz is an incredibly common clock rate for SD cards to run at.
It's "high speed" mode in SD (not very fast these days, but it used to
be) or:
#define HIGH_SPEED_MAX_DTR 50000000
If we don't support this then older "high speed" cards can only run at
25 MHz or at half their normal speed. There doesn't seem to be any
reason to skip this clock rate, so add it.
Fixes: 17269568f7 ("clk: qcom: Add Global Clock controller (GCC) driver for SC7180")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201210102234.2.I26dcc0cee374f5571d9929c9985f463773167e68@changeid
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
I would repeat the same commit message that was in commit 5e4b7e82d4
("clk: qcom: gcc-sdm845: Use floor ops for sdcc clks") but it seems
silly to do so when you could just go read that commit.
NOTE: this is actually extra terrible because we're missing the 50 MHz
rate in the table (see the next patch AKA ("clk: qcom: gcc-sc7180: Add
50 MHz clock rate for SDC2")). That means then when you run an older
SD card it'll try to clock it at 100 MHz when it's only specced to run
at 50 MHz max. As you can probably guess that doesn't work super
well.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Fixes: 17269568f7 ("clk: qcom: Add Global Clock controller (GCC) driver for SC7180")
Link: https://lore.kernel.org/r/20201210102234.1.I096779f219625148900fc984dd0084ed1ba87c7f@changeid
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The scpi_clk_match (struct of_device_id) is referenced only with
CONFIG_OF builds thus mark it as __maybe_unused:
drivers/clk/clk-scpi.c:132:34: warning:
‘scpi_clk_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201103162435.13689-8-krzk@kernel.org
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might be not relevant here). This
fixes compile warning (!CONFIG_OF && !CONFIG_MODULES):
drivers/clk/clk-pwm.c:139:34: warning:
‘clk_pwm_dt_ids’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201103162435.13689-1-krzk@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is no reason to keep on using the __raw_{read,write}l() I/O
accessors in Renesas ARM driver code. Switch to using the plain
{read,write}l() I/O accessors, to have a chance that this works on
big-endian.
Suggested-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20201119125053.4065746-1-geert+renesas@glider.be
Describe the RPCSRC internal clock and the RPC[D2] clocks derived from it,
as well as the RPC-IF module clock, in the RZ/G2E (R8A774C0) CPG/MSSR
driver.
Add new clk type CLK_TYPE_GEN3_E3_RPCSRC to register rpcsrc as a fixed
clock on R-Car Gen3 E3 (and also RZ/G2E which is identical to E3 SoC),
parent and the divider is set based on the register value CPG_RPCCKCR[4:3]
which has been set prior to booting the kernel.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20201116101002.5986-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The R-Car V3U clock driver defines the R and OSC clocks using R-Car Gen3
clock types. However, The R-Car V3U clock driver does not use the R-Car
Gen3 clock driver core, hence registering the R and OSC clocks fails:
renesas-cpg-mssr e6150000.clock-controller: Failed to register core clock osc: -22
renesas-cpg-mssr e6150000.clock-controller: Failed to register core clock r: -22
Fix this by introducing clock definition macros specific to R-Car V3U.
Note that rcar_r8a779a0_cpg_clk_register() already handled the related
clock types. Drop the now unneeded include of rcar-gen3-cpg.h.
Fixes: 17bcc8035d ("clk: renesas: cpg-mssr: Add support for R-Car V3U")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201109152614.2465483-1-geert+renesas@glider.be
Describe the RPCSRC internal clock and the RPC[D2] clocks derived from it,
as well as the RPC-IF module clock, in the RZ/G2N (R8A774B1) CPG/MSSR
driver.
Inspired by commit 94e3935b57 ("clk: renesas: r8a77980: Add RPC clocks").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20201016121709.8447-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Describe the RPCSRC internal clock and the RPC[D2] clocks derived from it,
as well as the RPC-IF module clock, in the RZ/G2M (R8A774A1) CPG/MSSR
driver.
Inspired by commit 94e3935b57 ("clk: renesas: r8a77980: Add RPC clocks").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20201016121709.8447-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When compiling with clang:
drivers/clk/renesas/r8a779a0-cpg-mssr.c:156:21: warning: no previous prototype for function 'rcar_r8a779a0_cpg_clk_register' [-Wmissing-prototypes]
struct clk * __init rcar_r8a779a0_cpg_clk_register(struct device *dev,
^
drivers/clk/renesas/r8a779a0-cpg-mssr.c:156:1: note: declare 'static' if the function is not intended to be used outside of this translation unit
struct clk * __init rcar_r8a779a0_cpg_clk_register(struct device *dev,
^
static
Similarly, with sparse:
drivers/clk/renesas/r8a779a0-cpg-mssr.c:156:12: warning: symbol 'rcar_r8a779a0_cpg_clk_register' was not declared. Should it be static?
There are no users of rcar_r8a779a0_cpg_clk_register() outside this
file, so it should be static.
Fixes: 17bcc8035d ("clk: renesas: cpg-mssr: Add support for R-Car V3U")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20200924111808.15358-1-geert+renesas@glider.be
1. Mark PM functions of newly added clkout module as unused to silence
!CONFIG_PM warnings.
2. Initialize ChipID driver later - in arch initcall.
-----BEGIN PGP SIGNATURE-----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=VCRg
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/drivers
Samsung SoC drivers changes for v5.11, part two
1. Mark PM functions of newly added clkout module as unused to silence
!CONFIG_PM warnings.
2. Initialize ChipID driver later - in arch initcall.
* tag 'samsung-drivers-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
clk: samsung: mark PM functions as __maybe_unused
soc: samsung: exynos-chipid: initialize later - with arch_initcall
soc: samsung: exynos-chipid: order list of SoCs by name
Link: https://lore.kernel.org/r/20201207074528.4475-1-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Driver changes for omaps for genpd for v5.11 merge window
This series of changes allows booting am335x with genpd and
device tree data without the legacy platform data. Also at
least am437x can be booted with gendp with power domain and
dts data. The SoC specific dts changes will be a separate
pull request.
We need the following driver changes merged before the dts
changes can be done:
- platform code needs a few improvments to probe l4_wkup first
for clocks, and to bail out when there is no platform data
- ti-sysc driver needs a non-urgent fix for asserting rstctrl
reset only after disabling the clocks, to probe modules with
no known control registers, and added quirk handling for gpmc
devices
- omap-prm driver needs a non-urgent fix for reset status bit,
support added for pm_clk, and then we add the rest of am335x
power domain data
- clock driver for am335x needs to keep l3_main clock enabled
with genpd for suspend and resume to work
- wkup_m3 remoteproc driver needs support added for reset
control if available instead of the legacy pdata callbacks
- pm33xx driver needs PM runtime support added for genpd
The am335x specific driver changes for the clock, wkup_m3,
pm33xx and remoteproc drivers are quite trivial and have not
caused merge conflicts in Linux next. I did not get acks for
these changes except from Santosh but had already pushed out
the branch already at that point. So I've added the related
driver maintainers to Cc.
* tag 'omap-for-v5.11/genpd-drivers-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
remoteproc/wkup_m3: Use reset control driver if available
soc: ti: pm33xx: Enable basic PM runtime support for genpd
soc: ti: omap-prm: am3: add genpd support for remaining PRM instances
soc: ti: omap-prm: Add pm_clk for genpd
clk: ti: am33xx: Keep am3 l3 main clock always on for genpd
bus: ti-sysc: Implement GPMC debug quirk to drop platform data
bus: ti-sysc: Support modules without control registers
ARM: OMAP2+: Probe PRCM first to probe l4_wkup with simple-pm-bus
ARM: OMAP2+: Check for inited flag
bus: ti-sysc: Assert reset only after disabling clocks
soc: ti: omap-prm: Do not check rstst bit on deassert if already deasserted
bus: ti-sysc: Fix bogus resetdone warning on enable for cpsw
bus: ti-sysc: Fix reset status check for modules with quirks
ARM: OMAP2+: Fix missing select PM_GENERIC_DOMAINS_OF
ARM: OMAP2+: Fix location for select PM_GENERIC_DOMAINS
Link: https://lore.kernel.org/r/pull-1606806458-694517@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add support for the FlexSPI clock on Freescale Layerscape SoCs. The
clock is a simple divider based one and is located inside the device
configuration space (DCFG).
This will allow switching the SCK frequencies for the FlexSPI interface
on the LS1028A and the LX2160A.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20201108185113.31377-8-michael@walle.cc
[sboyd@kernel.org: Drop modalias, add module table]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
To avoid future mistakes in the device tree for the clockgen module, add
constants for the clockgen subtype as well as a macro for the PLL
divider.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201108185113.31377-4-michael@walle.cc
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
AngeloGioacchino Del Regno