We can boot dra62x j5-eco using the dm814x code as the clocks and
devices are mapped in the device tree. The dra62x is also known
as jacinto 5 eco.
We may want to add separate soc_is macros for dra62x if needed,
but this gets us to the point where we can boot dra62x with just
dts changes.
Let's also print out the unknown hawkeye register to make things
a bit easier for new SoC variants.
Signed-off-by: Tony Lindgren <tony@atomide.com>
updates the EDMA bindings based on the various fixes to split EDMA into
separate independent devices. It also adds support for more devices on the
CompuLab cm-t335 and LogicPD Torpedo boards, and enables the new bindings
for qspi for am437x and dra7. There are also few dra7 regulator fixes, and
change of gpoi-key,wakeup to wakeup-source.
These depend on commit ae0add740c ("dmaengine: edma: DT: Change reserved
slot array from 16bit to 32bit type") already merged into mainline.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+G24
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Second set of omap device tree changes for v4.5 merge window. This series
updates the EDMA bindings based on the various fixes to split EDMA into
separate independent devices. It also adds support for more devices on the
CompuLab cm-t335 and LogicPD Torpedo boards, and enables the new bindings
for qspi for am437x and dra7. There are also few dra7 regulator fixes, and
change of gpoi-key,wakeup to wakeup-source.
These depend on commit ae0add740c ("dmaengine: edma: DT: Change reserved
slot array from 16bit to 32bit type") already merged into mainline.
* tag 'omap-for-v4.5/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: LogicPD Torpedo: Add Touchscreen Support
ARM: dts: DRA7-EVM: Add regulator-allow-bypass property for ldo9
ARM: dts: DRA72-EVM: Add regulator-allow-bypass property for ldo1 and ldo2
ARM: dts: AM4372: add entry for qspi mmap region
ARM: dts: DRA7: add entry for qspi mmap region
ARM: OMAP2+: LogicPD Torpedo: Revert Duplicative Entries
ARM: OMAP2+: LogicPD Torpedo + Wireless: Add Bluetooth
ARM: OMAP2+: LogicPD Torpedo: Add LCD Type 15 Support
ARM: dts: cm-t335: add support for bluetooth
ARM: dts: cm-t335: add support for DVI/LCD
ARM: dts: cm-t335: add support for I2C GPIO expander
ARM: dts: cm-t335: add support for SBC-T335
ARM: dts: cm-t335: add support for USB0
ARM: dts: omap: replace legacy *,wakeup property with wakeup-source
ARM: dts: am335x: replace gpio-key,wakeup with wakeup-source property
ARM: DTS: am437x: Use the new DT bindings for the eDMA3
ARM: DTS: am33xx: Use the new DT bindings for the eDMA3
dmaengine: edma: DT: Change reserved slot array from 16bit to 32bit type
dmaengine: edma: DT: Change memcpy channel array from 16bit to 32bit type
Signed-off-by: Olof Johansson <olof@lixom.net>
change the omap initcall levels a bit to initialize things later to allow
early device drivers at core_initcall level. This makes things easier
for us as most clocks can be made into regular device drivers except for
a few early clocks needed to initialize system timers. I wanted to have
these changes sit in Linux next for a few weeks before sending out a pull
request, and so far now issues have showed up.
The other changes in this series are timer changes for making use of the
new PWM driver, and timer changes to support more high security SoCs.
Also few minor improvments for module autoidle settings for ti81xx spinbox
and dra7 debug on uart4 in hwmod code. The rest is pretty much just removal
of platform data for SoCs that are all device tree only nowadays.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWeGDyAAoJEBvUPslcq6Vz/PsQALn5JcQgZe5Od95l4clQKKLT
OTDkRlfTUAWHNsDMNBqSAJZtRR4tWA4fECqusIyocJs2g74745MKcfuD1z0hSr+F
kvyYX/7lnS1AwU0RalACIoPlSh/ZR3Jrp4pXfiaNQGjr180SEmAtAu3jTUA4xUjZ
CdyILrzP7lckCUuF1vCguaM5hNqSEy0f6a1XCieG35k2nDrLq+C4QZ6YN8/ZGKLD
HADCFWllMcxgmTvxLy4JtUMYK/ujHJOl8QTEpUujzxRnZasZVJpB+lGsosIyR+d1
oXu9PaclyYYKK0/FtqQx2urhzu1POxaA8j2WDZB9k8Dt6csXZptkXoBdY7qJpOM2
0rL/57uv95hC1ufHVz6oRiRjvik0G4QL8M8cIpG4i4puTR0Uw+3HYy7UfYMsnK60
1piWmgaBb/VDYL/XTFE8FJW5WlEosWwezwoneY1yTCzMmtKX8KjFtxISYodrWuV8
rwnmLf5mn4/1HjmnqlYZHnCnMwdfbDsAV+5SPGIspkHT10un4wFgrLs9+2k3wntL
Je8H168+r9FS+ZND9kdN6HL+yf0ruC813l+p7cQ+RIy4hHyXoiFLeQnxAUcORNF5
0vUR47WZCMpgD2IjIDuDg9ZJp3gzEVNMbxbz5VpAwm4vgx/2QAMNs5l9Q8vQQd2O
uuHoE8Fi4KTY4LJTqPj6
=69mE
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/soc-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
SoC changes for omaps for v4.5 merge window. The main change here is to
change the omap initcall levels a bit to initialize things later to allow
early device drivers at core_initcall level. This makes things easier
for us as most clocks can be made into regular device drivers except for
a few early clocks needed to initialize system timers. I wanted to have
these changes sit in Linux next for a few weeks before sending out a pull
request, and so far now issues have showed up.
The other changes in this series are timer changes for making use of the
new PWM driver, and timer changes to support more high security SoCs.
Also few minor improvments for module autoidle settings for ti81xx spinbox
and dra7 debug on uart4 in hwmod code. The rest is pretty much just removal
of platform data for SoCs that are all device tree only nowadays.
* tag 'omap-for-v4.5/soc-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove device creation for omap-pcm-audio
ARM: OMAP1: Remove device creation for omap-pcm-audio
ARM: OMAP2+: Change core_initcall levels to postcore_initcall
ARM: DRA7: hwmod: Enable DEBUG_LL for UART4
ARM: OMAP: RX-51: fix a typo in log writing
ARM: omap4: hwmod: Remove elm address space from hwmod data
ARM: OMAP2+: timer: Remove secure timer for DRA7xx HS devices
ARM: OMAP: dmtimer: check for fixed timers during config
ARM: OMAP2+: Remove omap_mmu_dev_attr structure
ARM: OMAP4: hwmod data: Remove legacy IOMMU attr and addrs
ARM: OMAP3: hwmod data: Remove legacy IOMMU data
ARM: OMAP2+: Remove legacy device instantiation of IOMMUs
ARM: OMAP2+: Add hwmod spinbox support for dm816x
ARM: OMAP: add DT support for ti,dm816-timer
ARM: OMAP: dmtimer: Add clock source from DT
Signed-off-by: Olof Johansson <olof@lixom.net>
Make sure to tell the kernel that AM437x devices have ARM TWD timer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[grygorii.strashko@ti.com: drop ARM Global timer selection, because
it's incompatible with PM (cpuidle/cpufreq). So, it's unsafe to enable
it unconditionally]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
System will misbehave in the following case:
- AM43XX only build (UP);
- CONFIG_CPU_IDLE=y
- ARM TWD timer enabled and selected as clockevent device.
In the above case, It's expected that broadcast timer will be used as
backup timer when CPUIdle will put MPU in low power states where ARM
TWD will stop and lose its context. But, the CONFIG_SMP might not be
selected when kernel is built for AM43XX SoC only and, as result,
GENERIC_CLOCKEVENTS_BROADCAST option will not be selected also. This
will break CPUIdle and System will stuck in low power states.
Hence, fix it by selecting GENERIC_CLOCKEVENTS_BROADCAST option for
AM43XX SoCs always and add empty tick_broadcast() function
implementation - no need to send any IPI on UP. After this change
timer1 will be selected as broadcast timer the same way as for SMP,
and CPUIdle will work properly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap-pcm in ASoC is no longer a platform device. No need to create this
device anymore.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Bindings for the WL1283 Bluetooth was removed from the shared transport
driver in commit c0bd1b9e58 ("Revert ti-st: add device tree support")
Until we havea better binding, we need to use the platform data to
initialize Bluetooth.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
in mainline kernel with it's bootloader configured clocks. However,
trying to boot dm814x-evm uncovered all kind of issues with the timer
clock. To keep t410 booting, these issues need to be fixed in a specific
order and this branch contains both device tree and code changes.
To summarize the changes, we had missing ranges for clocks to probe,
missing aliase for clocks, wrong registers for divder clocks, and bad
address for the control module. All these went unnoticed earlier as
things worked without errors by luck and I did not pay much attention
to them until I got hold of a dm814x-evm and I noticed it did not boot.
As these are fixes for features that never worked, these can wait for
v4.5 merge window no problem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Mesm
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/81xx-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
Merge "omap fixes for 81xx for v4.5 merge window" from Tony Lindgren:
Fixes for ti81xx for v4.5 merge window. We have hp t410 already booting
in mainline kernel with it's bootloader configured clocks. However,
trying to boot dm814x-evm uncovered all kind of issues with the timer
clock. To keep t410 booting, these issues need to be fixed in a specific
order and this branch contains both device tree and code changes.
To summarize the changes, we had missing ranges for clocks to probe,
missing aliase for clocks, wrong registers for divder clocks, and bad
address for the control module. All these went unnoticed earlier as
things worked without errors by luck and I did not pay much attention
to them until I got hold of a dm814x-evm and I noticed it did not boot.
As these are fixes for features that never worked, these can wait for
v4.5 merge window no problem.
* tag 'omap-for-v4.5/81xx-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove useless check for legacy booting for dm814x
ARM: OMAP2+: Enable GPIO for dm814x
ARM: dts: Fix dm814x pinctrl address and mask
ARM: dts: Fix dm8148 control modules ranges
ARM: OMAP2+: Fix timer entries for dm814x
ARM: dts: Fix some mux and divider clocks to get dm814x-evm booting
ARM: OMAP2+: Add DPPLS clock manager for dm814x
clk: ti: Add few dm814x clock aliases
ARM: dts: Fix dm814x entries for pllss and prcm
We have never had dm814x booting properly with mainline kernel using
the legacy platform data based booting. Current minimal support is
device tree only.
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's a mux after the oscillator similar to am335x. I did not
notice this on hp t410 as it boots even with no clocks configured.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On dm814x we have some clocks at DPLLS and some at PRCM. Let's add a new
omap_prcm_init_data entry for the DPLLS so we can initalize timer clocks
early.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We want to be able to probe a few selected device drivers before hwmod
code populates the clocks in omap_hwmod_setup_all(). This allows us to
convert most of the clock drivers into regular device drivers.
We only need a few minimal clock drivers early for the system timers to
select between the 32KiHz clock and the high frequency oscillator.
With these changes, initializing the clock drivers can be just done at
core_initcall time with something like:
np = of_find_node_by_name(NULL, "plls");
if (np)
of_platform_populate(np, NULL, NULL, NULL);
And then these clocks will be available for the interconnect code to use.
Having most of the clock drivers being regular device drivers allows
us to use the nice things like devm_* functions and dev_err and dev_dbg.
As an extra bonus, this also allows us to develop the clock drivers for
new SoCs as loadable modules initially for cases where we can boot up
the system based on the bootloader configured clocks.
To do this, let's change the core_initcalls to postcore_initcall under
mach-omap2.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable REGULATOR_FIXED_VOLTAGE for all OMAP2+ platforms
otherwise system can't boot from SD-card when kernel is
built for single SoC (for example, with CONFIG_SOC_DRA7XX=y only).
It's also required for almost all TI SoC's platforms.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
UART4 low level debug support. This helps in debugging with UART4
serial console output on DRA7 based platforms.
Extending the following fix for UART4.
commit 1c7e36bfc3 ("ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL enabled on UART3")
For using DEBUG_LL, enable CONFIG_DEBUG_OMAP4UART4 in menuconfig.
On DRA7, UART4 hwmod doesn't have this flag enabled,
failure observed when UART4 is used for low level debugging.
Hence, Enable DEBUG_OMAP4UART4_FLAGS for UART4 hwmod.
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ELM address information is provided by device tree. No longer need
to include this information within hwmod.
This patch has only been boot tested.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Timer 12 on DRA7 SoCs is reserved for secure usage on high-secure (HS)
devices. The timer cannot be used by the kernel on HS devices, but is
available on regular general purpose (GP) devices. This is similar to the
behavior on OMAP3 devices, so extend the logic used in commit ad24bde8f1
("ARM: OMAP3: Dynamically disable secure timer nodes for secure devices")
to remove the secure timer on DRA7xx SoCs at run-time based on the SoC
device type.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Errata i810 states that DPLL controller can get stuck while transitioning
to a power saving state, while its M/N ratio is being re-programmed.
As a workaround, before re-programming the M/N ratio, SW has to ensure
the DPLL cannot start an idle state transition. SW can disable DPLL
idling by setting the DPLL AUTO_DPLL_MODE=0 or keeping a clock request
active by setting a dependent clock domain in SW_WKUP.
This errata impacts OMAP5 and DRA7 chips, so enable the errata for these.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
OMAP4 has been DT-boot only for some time, and the legacy-mode
device creation logic for IOMMU devices has also been cleaned up,
so the dev_attr and address data is no longer required. So, remove
these attribute data and hwmod addr space for the IPU & DSP IOMMU
devices.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The legacy-mode device creation logic for IOMMU devices has
been cleaned up, so the device attribute data, irq information
and address data are no longer required. Remove all of these
data for the ISP & IVA IOMMU devices.
Signed-off-by: Suman Anna <s-anna@ti.com>
[tony@atomide.com: updated to apply for the include]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The legacy-style IOMMU device creation is maintained currently only
for OMAP3 SoC, as all other SoCs are DT-boot only, and also to ensure
functionality of the OMAP3 ISP driver, the only in-kernel client user
on OMAP3 that supported both modes.
Commit 78c66fbcec ("[media] v4l: omap3isp: Drop platform data support")
removed the legacy device support from the OMAP3 ISP driver, so the
legacy device instantiation of OMAP IOMMU devices is no longer
needed, and is cleaned up.
Signed-off-by: Suman Anna <s-anna@ti.com>
[tony@atomide.com: updated to remove also the Makefile entry]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add dm81xx hwmod data entries for dm816x spinbox support.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP CPU hotplug uses cpu1's clocks and power domains for CPU1 wake up
from low power states (or turn on CPU1). This part of code is also
part of system suspend (disable_nonboot_cpus()).
>From other side, cpu1's clocks and power domains are used by CPUIdle. All above
functionality is mutually exclusive and, therefore, lockless clkdm/pwrdm api
can be used in omap4_boot_secondary().
This fixes below back-trace on -RT which is triggered by
pwrdm_lock/unlock():
BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:917
in_atomic(): 1, irqs_disabled(): 0, pid: 118, name: sh
9 locks held by sh/118:
#0: (sb_writers#4){.+.+.+}, at: [<c0144a6c>] vfs_write+0x13c/0x164
#1: (&of->mutex){+.+.+.}, at: [<c01b4c70>] kernfs_fop_write+0x48/0x19c
#2: (s_active#24){.+.+.+}, at: [<c01b4c78>] kernfs_fop_write+0x50/0x19c
#3: (device_hotplug_lock){+.+.+.}, at: [<c03cbff0>] lock_device_hotplug_sysfs+0xc/0x4c
#4: (&dev->mutex){......}, at: [<c03cd284>] device_online+0x14/0x88
#5: (cpu_add_remove_lock){+.+.+.}, at: [<c003af90>] cpu_up+0x50/0x1a0
#6: (cpu_hotplug.lock){++++++}, at: [<c003ae48>] cpu_hotplug_begin+0x0/0xc4
#7: (cpu_hotplug.lock#2){+.+.+.}, at: [<c003aec0>] cpu_hotplug_begin+0x78/0xc4
#8: (boot_lock){+.+...}, at: [<c002b254>] omap4_boot_secondary+0x1c/0x178
Preemption disabled at:[< (null)>] (null)
CPU: 0 PID: 118 Comm: sh Not tainted 4.1.12-rt11-01998-gb4a62c3-dirty #137
Hardware name: Generic DRA74X (Flattened Device Tree)
[<c0017574>] (unwind_backtrace) from [<c0013be8>] (show_stack+0x10/0x14)
[<c0013be8>] (show_stack) from [<c05a8670>] (dump_stack+0x80/0x94)
[<c05a8670>] (dump_stack) from [<c05ad158>] (rt_spin_lock+0x24/0x54)
[<c05ad158>] (rt_spin_lock) from [<c0030dac>] (clkdm_wakeup+0x10/0x2c)
[<c0030dac>] (clkdm_wakeup) from [<c002b2c0>] (omap4_boot_secondary+0x88/0x178)
[<c002b2c0>] (omap4_boot_secondary) from [<c0015d00>] (__cpu_up+0xc4/0x164)
[<c0015d00>] (__cpu_up) from [<c003b09c>] (cpu_up+0x15c/0x1a0)
[<c003b09c>] (cpu_up) from [<c03cd2d4>] (device_online+0x64/0x88)
[<c03cd2d4>] (device_online) from [<c03cd360>] (online_store+0x68/0x74)
[<c03cd360>] (online_store) from [<c01b4ce0>] (kernfs_fop_write+0xb8/0x19c)
[<c01b4ce0>] (kernfs_fop_write) from [<c0144124>] (__vfs_write+0x20/0xd8)
[<c0144124>] (__vfs_write) from [<c01449c0>] (vfs_write+0x90/0x164)
[<c01449c0>] (vfs_write) from [<c01451e4>] (SyS_write+0x44/0x9c)
[<c01451e4>] (SyS_write) from [<c0010240>] (ret_fast_syscall+0x0/0x54)
CPU1: smp_ops.cpu_die() returned, trying to resuscitate
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing HWMOD_NO_IDLEST hwmod flag for entries not
having omap4 clkctrl values.
The emac0 hwmod flag fixes the davinci_emac driver probe
since the return of pm_resume() call is now checked.
This solves the following boot errors :
[ 0.121429] omap_hwmod: l4_ls: _wait_target_ready failed: -16
[ 0.121441] omap_hwmod: l4_ls: cannot be enabled for reset (3)
[ 0.124342] omap_hwmod: l4_hs: _wait_target_ready failed: -16
[ 0.124352] omap_hwmod: l4_hs: cannot be enabled for reset (3)
[ 1.967228] omap_hwmod: emac0: _wait_target_ready failed: -16
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's not mix platform_data headers with the core headers. Instead, let's
create a subdir at linux/platform_data and move the headers to that
common place, adding it to MAINTAINERS.
The headers were moved with:
mkdir include/linux/platform_data/media/; git mv include/media/gpio-ir-recv.h include/media/ir-rx51.h include/media/mmp-camera.h include/media/omap1_camera.h include/media/omap4iss.h include/media/s5p_hdmi.h include/media/si4713.h include/media/sii9234.h include/media/smiapp.h include/media/soc_camera.h include/media/soc_camera_platform.h include/media/timb_radio.h include/media/timb_video.h include/linux/platform_data/media/
And the references fixed with this script:
MAIN_DIR="linux/platform_data/"
PREV_DIR="media/"
DIRS="media/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This is not needed anymore. Handling a potentially pending imprecise external
abort left behind by the bootloader is now done in a slightly safer way inside
the common ARM startup code.
With the recent changes to abort handling, this issue got fixed by 57df538085
("ARM: OMAP2+: Fix imprecise external abort caused by bogus SRAM init").
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
[tony@atomide.com: updated comments to describe what fixed the issue]
Signed-off-by: Tony Lindgren <tony@atomide.com>
McASP3 is used by default on DRA7x based boards for audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some module needs more than one functional clock in order to be accessible,
like the McASPs found in DRA7xx family.
This flag will indicate that the opt_clks need to be handled at the same
time as the main_clk for the given hwmod, ensuring that all needed clocks
are enabled before we try to access the module's address space.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Again we have a sizable (but not huge) cleanup branch with a net delta of about
-3k lines.
Main contents here is:
- A bunch of development/cleanup of a few PXA boards
- Removal of bockw platforms on shmobile, since the platform has now gone
completely multiplatform. Whee!
- move of the 32kHz timer on OMAP to a proper timesource
- Misc cleanup of older OMAP material (incl removal of one board file)
- Switch over to new common PWM lookup support for several platforms
There's also a handful of other cleanups across the tree, but the above are
the major pieces.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=uI7R
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"Again we have a sizable (but not huge) cleanup branch with a net delta
of about -3k lines.
Main contents here is:
- A bunch of development/cleanup of a few PXA boards
- Removal of bockw platforms on shmobile, since the platform has now
gone completely multiplatform. Whee!
- move of the 32kHz timer on OMAP to a proper timesource
- Misc cleanup of older OMAP material (incl removal of one board
file)
- Switch over to new common PWM lookup support for several platforms
There's also a handful of other cleanups across the tree, but the
above are the major pieces"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (103 commits)
ARM: OMAP3: hwmod data: Remove legacy mailbox data and addrs
ARM: DRA7: hwmod data: Remove spinlock hwmod addrs
ARM: OMAP4: hwmod data: Remove spinlock hwmod addrs
ARM: DRA7/AM335x/AM437x: hwmod: Remove gpmc address space from hwmod data
ARM: Remove __ref on hotplug cpu die path
ARM: Remove open-coded version of IRQCHIP_DECLARE
arm: omap2: board-generic: use omap4_local_timer_init for AM437x
ARM: DRA7/AM335x/AM437x: hwmod: Remove elm address space from hwmod data
ARM: OMAP: Remove duplicated operand in OR operation
clocksource: ti-32k: make it depend on GENERIC_CLOCKSOURCE
ARM: pxa: remove incorrect __init annotation on pxa27x_set_pwrmode
ARM: pxa: raumfeld: make some variables static
ARM: OMAP: Change all cpu_is_* occurences to soc_is_* for id.c
ARM: OMAP2+: Rename cpu_is macros to soc_is
arm: omap2: timer: limit hwmod usage to non-DT boots
arm: omap2+: select 32k clocksource driver
clocksource: add TI 32.768 Hz counter driver
arm: omap2: timer: rename omap_sync32k_timer_init()
arm: omap2: timer: always call clocksource_of_init() when DT
arm: omap2: timer: move realtime_counter_init() around
...
This time we have a very typical update which is mostly fixes and updates to
drivers and no new drivers.
- Biggest change is coming from Peter for edma cleanup which even caused
some last minute regression, things seem settled now
- idma64 and dw updates
- iotdma updates
- module autoload fixes for various drivers
- scatter gather support for hdmac
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tIzO
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.4-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we have a very typical update which is mostly fixes and
updates to drivers and no new drivers.
- the biggest change is coming from Peter for edma cleanup which even
caused some last minute regression, things seem settled now
- idma64 and dw updates
- iotdma updates
- module autoload fixes for various drivers
- scatter gather support for hdmac"
* tag 'dmaengine-4.4-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (77 commits)
dmaengine: edma: Add dummy driver skeleton for edma3-tptc
Revert "ARM: DTS: am33xx: Use the new DT bindings for the eDMA3"
Revert "ARM: DTS: am437x: Use the new DT bindings for the eDMA3"
dmaengine: dw: some Intel devices has no memcpy support
dmaengine: dw: platform: provide platform data for Intel
dmaengine: dw: don't override platform data with autocfg
dmaengine: hdmac: Add scatter-gathered memset support
dmaengine: hdmac: factorise memset descriptor allocation
dmaengine: virt-dma: Fix kernel-doc annotations
ARM: DTS: am437x: Use the new DT bindings for the eDMA3
ARM: DTS: am33xx: Use the new DT bindings for the eDMA3
dmaengine: edma: New device tree binding
dmaengine: Kconfig: edma: Select TI_DMA_CROSSBAR in case of ARCH_OMAP
dmaengine: ti-dma-crossbar: Add support for crossbar on AM33xx/AM43xx
dmaengine: edma: Merge the of parsing functions
dmaengine: edma: Do not allocate memory for edma_rsv_info in case of DT boot
dmaengine: edma: Refactor the dma device and channel struct initialization
dmaengine: edma: Get qDMA channel information from HW also
dmaengine: edma: Merge map_dmach_to_queue into assign_channel_eventq
dmaengine: edma: Correct PaRAM access function names (_parm_ to _param_)
...
- ACPICA update to upstream revision 20150930 (Bob Moore, Lv Zheng).
The most significant change is to allow the AML debugger to be
built into the kernel. On top of that there is an update related
to the NFIT table (the ACPI persistent memory interface)
and a few fixes and cleanups.
- ACPI CPPC2 (Collaborative Processor Performance Control v2)
support along with a cpufreq frontend (Ashwin Chaugule).
This can only be enabled on ARM64 at this point.
- New ACPI infrastructure for the early probing of IRQ chips and
clock sources (Marc Zyngier).
- Support for a new hierarchical properties extension of the ACPI
_DSD (Device Specific Data) device configuration object allowing
the kernel to handle hierarchical properties (provided by the
platform firmware this way) automatically and make them available
to device drivers via the generic device properties interface
(Rafael Wysocki).
- Generic device properties API extension to obtain an index of
certain string value in an array of strings, along the lines of
of_property_match_string(), but working for all of the supported
firmware node types, and support for the "dma-names" device
property based on it (Mika Westerberg).
- ACPI core fix to parse the MADT (Multiple APIC Description Table)
entries in the order expected by platform firmware (and mandated
by the specification) to avoid confusion on systems with more than
255 logical CPUs (Lukasz Anaczkowski).
- Consolidation of the ACPI-based handling of PCI host bridges
on x86 and ia64 (Jiang Liu).
- ACPI core fixes to ensure that the correct IRQ number is used to
represent the SCI (System Control Interrupt) in the cases when
it has been re-mapped (Chen Yu).
- New ACPI backlight quirk for Lenovo IdeaPad S405 (Hans de Goede).
- ACPI EC driver fixes (Lv Zheng).
- Assorted ACPI fixes and cleanups (Dan Carpenter, Insu Yun, Jiri
Kosina, Rami Rosen, Rasmus Villemoes).
- New mechanism in the PM core allowing drivers to check if the
platform firmware is going to be involved in the upcoming system
suspend or if it has been involved in the suspend the system is
resuming from at the moment (Rafael Wysocki).
This should allow drivers to optimize their suspend/resume
handling in some cases and the changes include a couple of users
of it (the i8042 input driver, PCI PM).
- PCI PM fix to prevent runtime-suspended devices with PME enabled
from being resumed during system suspend even if they aren't
configured to wake up the system from sleep (Rafael Wysocki).
- New mechanism to report the number of a wakeup IRQ that woke up
the system from sleep last time (Alexandra Yates).
- Removal of unused interfaces from the generic power domains
framework and fixes related to latency measurements in that
code (Ulf Hansson, Daniel Lezcano).
- cpufreq core sysfs interface rework to make it handle CPUs that
share performance scaling settings (represented by a common
cpufreq policy object) more symmetrically (Viresh Kumar).
This should help to simplify the CPU offline/online handling among
other things.
- cpufreq core fixes and cleanups (Viresh Kumar).
- intel_pstate fixes related to the Turbo Activation Ratio (TAR)
mechanism on client platforms which causes the turbo P-states
range to vary depending on platform firmware settings (Srinivas
Pandruvada).
- intel_pstate sysfs interface fix (Prarit Bhargava).
- Assorted cpufreq driver (imx, tegra20, powernv, integrator) fixes
and cleanups (Bai Ping, Bartlomiej Zolnierkiewicz, Shilpasri G
Bhat, Luis de Bethencourt).
- cpuidle mvebu driver cleanups (Russell King).
- OPP (Operating Performance Points) framework code reorganization
to make it more maintainable (Viresh Kumar).
- Intel Broxton support for the RAPL (Running Average Power Limits)
power capping driver (Amy Wiles).
- Assorted power management code fixes and cleanups (Dan Carpenter,
Geert Uytterhoeven, Geliang Tang, Luis de Bethencourt, Rasmus
Villemoes).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=1gaH
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.4-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"Quite a new features are included this time.
First off, the Collaborative Processor Performance Control interface
(version 2) defined by ACPI will now be supported on ARM64 along with
a cpufreq frontend for CPU performance scaling.
Second, ACPI gets a new infrastructure for the early probing of IRQ
chips and clock sources (along the lines of the existing similar
mechanism for DT).
Next, the ACPI core and the generic device properties API will now
support a recently introduced hierarchical properties extension of the
_DSD (Device Specific Data) ACPI device configuration object. If the
ACPI platform firmware uses that extension to organize device
properties in a hierarchical way, the kernel will automatically handle
it and make those properties available to device drivers via the
generic device properties API.
It also will be possible to build the ACPICA's AML interpreter
debugger into the kernel now and use that to diagnose AML-related
problems more efficiently. In the future, this should make it
possible to single-step AML execution and do similar things.
Interesting stuff, although somewhat experimental at this point.
Finally, the PM core gets a new mechanism that can be used by device
drivers to distinguish between suspend-to-RAM (based on platform
firmware support) and suspend-to-idle (or other variants of system
suspend the platform firmware is not involved in) and possibly
optimize their device suspend/resume handling accordingly.
In addition to that, some existing features are re-organized quite
substantially.
First, the ACPI-based handling of PCI host bridges on x86 and ia64 is
unified and the common code goes into the ACPI core (so as to reduce
code duplication and eliminate non-essential differences between the
two architectures in that area).
Second, the Operating Performance Points (OPP) framework is
reorganized to make the code easier to find and follow.
Next, the cpufreq core's sysfs interface is reorganized to get rid of
the "primary CPU" concept for configurations in which the same
performance scaling settings are shared between multiple CPUs.
Finally, some interfaces that aren't necessary any more are dropped
from the generic power domains framework.
On top of the above we have some minor extensions, cleanups and bug
fixes in multiple places, as usual.
Specifics:
- ACPICA update to upstream revision 20150930 (Bob Moore, Lv Zheng).
The most significant change is to allow the AML debugger to be
built into the kernel. On top of that there is an update related
to the NFIT table (the ACPI persistent memory interface) and a few
fixes and cleanups.
- ACPI CPPC2 (Collaborative Processor Performance Control v2) support
along with a cpufreq frontend (Ashwin Chaugule).
This can only be enabled on ARM64 at this point.
- New ACPI infrastructure for the early probing of IRQ chips and
clock sources (Marc Zyngier).
- Support for a new hierarchical properties extension of the ACPI
_DSD (Device Specific Data) device configuration object allowing
the kernel to handle hierarchical properties (provided by the
platform firmware this way) automatically and make them available
to device drivers via the generic device properties interface
(Rafael Wysocki).
- Generic device properties API extension to obtain an index of
certain string value in an array of strings, along the lines of
of_property_match_string(), but working for all of the supported
firmware node types, and support for the "dma-names" device
property based on it (Mika Westerberg).
- ACPI core fix to parse the MADT (Multiple APIC Description Table)
entries in the order expected by platform firmware (and mandated by
the specification) to avoid confusion on systems with more than 255
logical CPUs (Lukasz Anaczkowski).
- Consolidation of the ACPI-based handling of PCI host bridges on x86
and ia64 (Jiang Liu).
- ACPI core fixes to ensure that the correct IRQ number is used to
represent the SCI (System Control Interrupt) in the cases when it
has been re-mapped (Chen Yu).
- New ACPI backlight quirk for Lenovo IdeaPad S405 (Hans de Goede).
- ACPI EC driver fixes (Lv Zheng).
- Assorted ACPI fixes and cleanups (Dan Carpenter, Insu Yun, Jiri
Kosina, Rami Rosen, Rasmus Villemoes).
- New mechanism in the PM core allowing drivers to check if the
platform firmware is going to be involved in the upcoming system
suspend or if it has been involved in the suspend the system is
resuming from at the moment (Rafael Wysocki).
This should allow drivers to optimize their suspend/resume handling
in some cases and the changes include a couple of users of it (the
i8042 input driver, PCI PM).
- PCI PM fix to prevent runtime-suspended devices with PME enabled
from being resumed during system suspend even if they aren't
configured to wake up the system from sleep (Rafael Wysocki).
- New mechanism to report the number of a wakeup IRQ that woke up the
system from sleep last time (Alexandra Yates).
- Removal of unused interfaces from the generic power domains
framework and fixes related to latency measurements in that code
(Ulf Hansson, Daniel Lezcano).
- cpufreq core sysfs interface rework to make it handle CPUs that
share performance scaling settings (represented by a common cpufreq
policy object) more symmetrically (Viresh Kumar).
This should help to simplify the CPU offline/online handling among
other things.
- cpufreq core fixes and cleanups (Viresh Kumar).
- intel_pstate fixes related to the Turbo Activation Ratio (TAR)
mechanism on client platforms which causes the turbo P-states range
to vary depending on platform firmware settings (Srinivas
Pandruvada).
- intel_pstate sysfs interface fix (Prarit Bhargava).
- Assorted cpufreq driver (imx, tegra20, powernv, integrator) fixes
and cleanups (Bai Ping, Bartlomiej Zolnierkiewicz, Shilpasri G
Bhat, Luis de Bethencourt).
- cpuidle mvebu driver cleanups (Russell King).
- OPP (Operating Performance Points) framework code reorganization to
make it more maintainable (Viresh Kumar).
- Intel Broxton support for the RAPL (Running Average Power Limits)
power capping driver (Amy Wiles).
- Assorted power management code fixes and cleanups (Dan Carpenter,
Geert Uytterhoeven, Geliang Tang, Luis de Bethencourt, Rasmus
Villemoes)"
* tag 'pm+acpi-4.4-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (108 commits)
cpufreq: postfix policy directory with the first CPU in related_cpus
cpufreq: create cpu/cpufreq/policyX directories
cpufreq: remove cpufreq_sysfs_{create|remove}_file()
cpufreq: create cpu/cpufreq at boot time
cpufreq: Use cpumask_copy instead of cpumask_or to copy a mask
cpufreq: ondemand: Drop unnecessary locks from update_sampling_rate()
PM / Domains: Merge measurements for PM QoS device latencies
PM / Domains: Don't measure ->start|stop() latency in system PM callbacks
PM / clk: Fix broken build due to non-matching code and header #ifdefs
ACPI / Documentation: add copy_dsdt to ACPI format options
ACPI / sysfs: correctly check failing memory allocation
ACPI / video: Add a quirk to force native backlight on Lenovo IdeaPad S405
ACPI / CPPC: Fix potential memory leak
ACPI / CPPC: signedness bug in register_pcc_channel()
ACPI / PAD: power_saving_thread() is not freezable
ACPI / PM: Fix incorrect wakeup IRQ setting during suspend-to-idle
ACPI: Using correct irq when waiting for events
ACPI: Use correct IRQ when uninstalling ACPI interrupt handler
cpuidle: mvebu: disable the bind/unbind attributes and use builtin_platform_driver
cpuidle: mvebu: clean up multiple platform drivers
...
Pull irq updates from Thomas Gleixner:
"The irq departement delivers:
- Rework the irqdomain core infrastructure to accomodate ACPI based
systems. This is required to support ARM64 without creating
artificial device tree nodes.
- Sanitize the ACPI based ARM GIC initialization by making use of the
new firmware independent irqdomain core
- Further improvements to the generic MSI management
- Generalize the irq migration on CPU hotplug
- Improvements to the threaded interrupt infrastructure
- Allow the migration of "chained" low level interrupt handlers
- Allow optional force masking of interrupts in disable_irq[_nosysnc]
- Support for two new interrupt chips - Sigh!
- A larger set of errata fixes for ARM gicv3
- The usual pile of fixes, updates, improvements and cleanups all
over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (71 commits)
Document that IRQ_NONE should be returned when IRQ not actually handled
PCI/MSI: Allow the MSI domain to be device-specific
PCI: Add per-device MSI domain hook
of/irq: Use the msi-map property to provide device-specific MSI domain
of/irq: Split of_msi_map_rid to reuse msi-map lookup
irqchip/gic-v3-its: Parse new version of msi-parent property
PCI/MSI: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
of/irq: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
of/irq: Add support code for multi-parent version of "msi-parent"
irqchip/gic-v3-its: Add handling of PCI requester id.
PCI/MSI: Add helper function pci_msi_domain_get_msi_rid().
of/irq: Add new function of_msi_map_rid()
Docs: dt: Add PCI MSI map bindings
irqchip/gic-v2m: Add support for multiple MSI frames
irqchip/gic-v3: Fix translation of LPIs after conversion to irq_fwspec
irqchip/mxs: Add Alphascale ASM9260 support
irqchip/mxs: Prepare driver for hardware with different offsets
irqchip/mxs: Panic if ioremap or domain creation fails
irqdomain: Documentation updates
irqdomain/msi: Use fwnode instead of of_node
...
bit of time sorting out regressions for v4.3 and are very late with
these, I've kept the changes down to minimum:
- A series of timer changes from Felipe Balbi to get us closer to
moving the remaining timer code into drivers
- A series of hwmod clean-up changes queued by Paul Walmsley
- SoC detection clean-up to use soc_is instead of cpu_is as CPU is
within the SoC and is confusing naming. The rest we can now change
along with the other clean-up
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gNfn
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.4/soc-clean-up' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Minimal omap SoC changes for v4.4 merge window. As we've spent quite a
bit of time sorting out regressions for v4.3 and are very late with
these, I've kept the changes down to minimum:
- A series of timer changes from Felipe Balbi to get us closer to
moving the remaining timer code into drivers
- A series of hwmod clean-up changes queued by Paul Walmsley
- SoC detection clean-up to use soc_is instead of cpu_is as CPU is
within the SoC and is confusing naming. The rest we can now change
along with the other clean-up
* tag 'omap-for-v4.4/soc-clean-up' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (21 commits)
ARM: OMAP3: hwmod data: Remove legacy mailbox data and addrs
ARM: DRA7: hwmod data: Remove spinlock hwmod addrs
ARM: OMAP4: hwmod data: Remove spinlock hwmod addrs
ARM: DRA7/AM335x/AM437x: hwmod: Remove gpmc address space from hwmod data
arm: omap2: board-generic: use omap4_local_timer_init for AM437x
ARM: DRA7/AM335x/AM437x: hwmod: Remove elm address space from hwmod data
ARM: OMAP: Remove duplicated operand in OR operation
clocksource: ti-32k: make it depend on GENERIC_CLOCKSOURCE
ARM: OMAP: Change all cpu_is_* occurences to soc_is_* for id.c
ARM: OMAP2+: Rename cpu_is macros to soc_is
arm: omap2: timer: limit hwmod usage to non-DT boots
arm: omap2+: select 32k clocksource driver
clocksource: add TI 32.768 Hz counter driver
arm: omap2: timer: rename omap_sync32k_timer_init()
arm: omap2: timer: always call clocksource_of_init() when DT
arm: omap2: timer: move realtime_counter_init() around
arm: omap2: timer: provide generic sync32k_timer_init function
arm: omap2: timer: remove __omap_gptimer_init()
arm: omap2: timer: add a gptimer argument to sync32k_timer_init()
arm: omap2: timer: get rid of obfuscating macros
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Remove some superfluous data from the OMAP2+ hwmod data files. Mostly
this is a result of data being moved to DT files. Nothing too
controversial, here.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/hwmod-cleanup-a-for-v4.4/20151023130140/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AVI9
-----END PGP SIGNATURE-----
Merge tag 'for-v4.4/omap-hwmod-cleanup-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.4/soc
ARM: OMAP2+: hwmod cleanup for v4.4
Remove some superfluous data from the OMAP2+ hwmod data files. Mostly
this is a result of data being moved to DT files. Nothing too
controversial, here.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/hwmod-cleanup-a-for-v4.4/20151023130140/
Remove the mailbox attribute data, irq info and hwmod addr space
data that are used for creating the legacy-style mailbox devices,
there is no need for these as the support for legacy-mode for this
IP is being dropped.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The legacy-style device creation logic for hwspinlock
has been removed after the DT-support was added to the
driver. The hwmod addr space for spinlock is therefore
no longer needed, so remove it.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The legacy-style device creation logic for hwspinlock
has been removed after the DT-support was added to the
driver. The hwmod addr space for spinlock is therefore
no longer needed, so remove it.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
GPMC address information is provided by device tree. No longer need
to include this information within hwmod.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
[paul@pwsan.com: fixed chip names in subject line]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Now that __cpuinit has been removed, the __ref markings on these
functions are useless. Remove them. This also reduces the size of
the multi_v7_defconfig image:
$ size before after
text data bss dec hex filename
12683578 1470996 348904 14503478 dd4e36 before
12683274 1470996 348904 14503174 dd4d06 after
presumably because now we don't have to jump to code in the
.ref.text section and/or the noinline marking is removed.
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: <linux-omap@vger.kernel.org>
Cc: <linux-arm-msm@vger.kernel.org>
Cc: <spear-devel@list.st.com>
Cc: <linux-tegra@vger.kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Barry Song <baohua@kernel.org>
Acked-by: Andy Gross <agross@codeaurora.org>
Acked-by: Viresh Kumar <vireshk@kernel.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Now that the IRQCHIP_DECLARE macro has been moved to linux/irqchip.h,
it becomes possible to cleanup the open-coded versions of the same
macro that have been added to some private irqchips implementations.
Cc: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Kukjin Kim <kgene@kernel.org>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
AM437x-based boards, can use omap4_local_timer_init()
just fine. Let's use that instead.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ELM address information is provided by device tree. No longer need
to include this information within hwmod.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
[paul@pwsan.com: fixed chip names in subject line; dropped the OMAP4 section
since the OMAP4 SoC DTS file doesn't have the ELM address space documented
yet]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit b483a4a5a7 ("ARM: OMAP4+: hwmod data: Don't prevent RESET of
USB Host module") added the SYSC_HAS_RESET_STATUS flag to both OMAP4
and OMAP5 USB host module hwmon sysconfig but that flag was already
set for OMAP5. So now the flag appears twice in the expression.
make coccicheck complains with the following message:
omap_hwmod_54xx_data.c:1846:37-58: duplicated argument to & or |
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some omaps are producing imprecise external aborts because we are
wrongly trying to init SRAM for device tree based booting. Only
omap3 is still using the legacy SRAM code, so we need to make it
omap3 specific. Otherwise we can get errors like this on at least
dm814x:
Unhandled fault: imprecise external abort (0xc06) at 0xc08b156c
...
(omap_rev) from [<c08b12e0>] (omap_sram_init+0xf8/0x3e0)
(omap_sram_init) from [<c08aca0c>] (omap_sdrc_init+0x10/0xb0)
(omap_sdrc_init) from [<c08b581c>] (pdata_quirks_init+0x18/0x44)
(pdata_quirks_init) from [<c08b5478>] (omap_generic_init+0x10/0x1c)
(omap_generic_init) from [<c08a57e0>] (customize_machine+0x1c/0x40)
(customize_machine) from [<c00098a4>] (do_one_initcall+0x80/0x1dc)
(do_one_initcall) from [<c08a2ec4>] (kernel_init_freeable+0x218/0x2e8)
(kernel_init_freeable) from [<c063a554>] (kernel_init+0x8/0xec)
(kernel_init) from [<c000f890>] (ret_from_fork+0x14/0x24)
Let's fix the issue by making sure omap_sdrc_init only gets called for
omap3. To do that, we need to have compatible "ti,omap3" in the dts
files. And let's also use "ti,omap3630" instead of "ti,omap36xx" like
we're supposed to.
Signed-off-by: Tony Lindgren <tony@atomide.com>
On boards with more than 2GB of RAM booting goes wrong with things not
working and we're getting lots of l3 warnings:
WARNING: CPU: 0 PID: 1 at drivers/bus/omap_l3_noc.c:147
l3_interrupt_handler+0x260/0x384()
44000000.ocp:L3 Custom Error: MASTER MMC6 TARGET DMM1 (Idle):
Data Access in User mode during Functional access
...
[<c044e158>] (scsi_add_host_with_dma) from [<c04705c8>]
(ata_scsi_add_hosts+0x5c/0x18c)
[<c04705c8>] (ata_scsi_add_hosts) from [<c046b13c>]
(ata_host_register+0x150/0x2cc)
[<c046b13c>] (ata_host_register) from [<c046b38c>]
(ata_host_activate+0xd4/0x124)
[<c046b38c>] (ata_host_activate) from [<c047f42c>]
(ahci_host_activate+0x5c/0x194)
[<c047f42c>] (ahci_host_activate) from [<c0480854>]
(ahci_platform_init_host+0x1f0/0x3f0)
[<c0480854>] (ahci_platform_init_host) from [<c047c9dc>]
(ahci_probe+0x70/0x98)
[<c047c9dc>] (ahci_probe) from [<c04220cc>]
(platform_drv_probe+0x54/0xb4)
Let's fix the issue by enabling ZONE_DMA for LPAE. Note that we need to
limit dma_zone_size to 2GB as the rest of the RAM is beyond the 4GB limit.
Let's also fix things for dra7 as done in similar patches in the TI tree
by Lokesh Vutla <lokeshvutla@ti.com>.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently apart from dra7, omap5 and amx3 all the other SoCs
are identified using cpu_is_* functions which is not right since
they are all SoCs(System on Chips). Hence changing the SoC
identification code to use soc_is instead of cpu_is and keeping
defines for cpu_is where needed. This allows us to replace the
rest of cpu_is usage along with other fixes as needed.
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Keerthy <j-keerthy@ti.com>
[tony@atomide.com: reworked the soc.h changes to minimum]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The naming for the cpu_is macros is confusing as the CPU is separate
and within the SoC. Let's rename all the macros to soc_is, and let's
define cpu_is also for the ones still in use. Then we can just remove
the cpu_is macros once the users are fixed up.
To keep the chances of breaking anything, the changes were
generated with the following regular expressions:
s/cpu_is/soc_is/g
s/CPU/SoC/g
Then the list of existing cpu_is users was generated with:
$ $ grep -o -e 'cpu_is_.\+()' arch/arm/mach-omap2/*.[chS] | \
cut -d: -f2 | sort | uniq
And added to the end of the soc.h.
I decided to rework the earlier patches by Keerthy <j-keerthy@ti.com>
to keep changes down to minimum to avoid potential errors and stick
to just search and replace.
Signed-off-by: Tony Lindgren <tony@atomide.com>
now that we have a working 32k clocksource driver,
we can limit HWMOD usage to non-DT boots and rely
on clocksource_of_init() every time we boot
with DT.
While at that, also make sure that we don't disable
the 32-counter device so it gets probed by its driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
this function is not only about the 32k sync
timer, it's OMAP's generic init_time implementation.
Let's rename it to make that detail easier to
notice.
Signed-off-by: Felipe Balbi <balbi@ti.com>
If booting with DT, let's make sure to always
call clocksource_of_init() as this will make
it easier to move timer code to drivers/clocksource
in the future.
Signed-off-by: Felipe Balbi <balbi@ti.com>
instead of constantly defining a small wrapper
around __omap_sync32k_timer_init(), let's define
a generic one which can be used by all OMAPs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
__omap_sync32k_timer_init(), now takes the clock
source as a parameter. This means we no longer need
__omap_gptimer_init().
Note that __omap_sync32k_timer_init() will be
renamed in a follow-up patch as it's not longer 32k
source specific.
Signed-off-by: Felipe Balbi <balbi@ti.com>
as it turns out, __omap_gptimer_init() and
__omap_sync32k_timer_init() are essentially
the same thing, but __omap_gptimer_init() wants
to always use gptimer.
Instead of forcing all those devices to pass
a use_gptimer cmdline argument, we add a new
function argument to __omap_sync32k_timer_init()
in preparation to deleting __omap_gptimer_init().
On a follow-up patch, we will remove uses of
__omap_gptimer_init() and replace them with
__omap_sync32k_timer_init() and pass the last
argument as true.
Signed-off-by: Felipe Balbi <balbi@ti.com>
those macros just make it a lot more difficult
to grep around and actually find similarities.
In this patch, we will simply remove them and
replace with actual functions and later commits
will come to further clean this up.
Signed-off-by: Felipe Balbi <balbi@ti.com>
omap4_local_timer_init() can be used by other
platforms as is. At least AM437x wants to use
it. Instead of making omap4-only and providing
a stub for builds without OMAP4, we can just
make sure that function is always available
for all SoCs that need it.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove the OMAP3 core DPLL re-program code, and the associated SRAM
code that does the low-level programming of the DPLL divider, idling
of the SDRAM etc.
This code was never fully implemented in the kernel; things missing
were driver side handling of core clock changes (they need to account
for their functional clock rate being changed on-the-fly), and the whole
framework required for handling this. Thus, there is not much point
to keep carrying the low-level support code either.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the code out from arch/arm/common and merge it inside of the dmaengine
driver.
This change is done with as minimal (if eny) functional change to the code
as possible to avoid introducing regression.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since we now have a generic data structure to express an
interrupt specifier, convert all hierarchical irqchips that
are OF based to use a fwnode_handle as part of their alloc
and xlate (which becomes translate) callbacks.
As most of these drivers have dependencies (they exchange IRQ
specifiers), change them all in a single, massive patch...
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-6-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The struct irq_domain contains a "struct device_node *" field
(of_node) that is almost the only link between the irqdomain
and the device tree infrastructure.
In order to prepare for the removal of that field, convert all
users to use irq_domain_get_of_node() instead.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-and-tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The cpuidle tracepoints are called within a rcu_idle_exit() section, and
must be denoted with the _rcuidle() version of the tracepoint.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the unneded semicolons since they are clearly a typo error.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PRM_POLCTRL_TWL_MASK and PRM_POLCTRL_TWL_MASK
macros are not used so they can be deleted.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP3 ISP is now fully supported in DT, remove its instantiation
from C code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Seeing the 'of' characters in a symbol that is being called from
ACPI seems to freak out people. So let's do a bit of pointless
renaming so that these folks do feel at home.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Our first real batch of fixes this release cycle. There's a collection of
them here:
- A fixup for a build breakage that hits on arm64 allmodconfig in QCOM SCM
firmware drivers
- MMC fixes for OMAP that had quite a bit of breakage this merge window.
- Misc build/warning fixes on PXA and OMAP
- A couple of minor fixes for Beagleboard X15 which is now starting to see
a few more users in the wild
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ThcO
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Our first real batch of fixes this release cycle. Nothing really
concerning, and diffstat is a bit inflated due to some DT contents
moving around on STi platforms.
There's a collection of them here:
- A fixup for a build breakage that hits on arm64 allmodconfig in
QCOM SCM firmware drivers
- MMC fixes for OMAP that had quite a bit of breakage this merge
window.
- Misc build/warning fixes on PXA and OMAP
- A couple of minor fixes for Beagleboard X15 which is now starting
to see a few more users in the wild"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
ARM: sti: dt: adapt DT to fix probe/bind issues in DRM driver
ARM: dts: fix omap2+ address translation for pbias
firmware: qcom: scm: Add function stubs for ARM64
ARM: dts: am57xx-beagle-x15: use palmas-usb for USB2
ARM: omap2plus_defconfig: enable GPIO_PCA953X
ARM: dts: omap5-uevm.dts: fix i2c5 pinctrl offsets
ARM: OMAP2+: AM43XX: Enable autoidle for clks in am43xx_init_late
ARM: dts: am57xx-beagle-x15: Update Phy supplies
ARM: pxa: balloon3: Fix build error
ARM: dts: Fixup model name for HP t410 dts
ARM: dts: DRA7: fix a typo in ethernet
ARM: omap2plus_defconfig: make PCF857x built-in
ARM: dts: Use ti,pbias compatible string for pbias
ARM: OMAP5: Cleanup options for SoC only build
ARM: DRA7: Select missing options for SoC only build
ARM: OMAP2+: board-generic: Remove stale of_irq macros
ARM: OMAP4+: PM: erratum is used by OMAP5 and DRA7 as well
ARM: dts: omap3-igep: Move eth IRQ pinmux to IGEPv2 common dtsi
ARM: dts: am57xx-beagle-x15: Add wakeup irq for mcp79410
ARM: dts: am335x-phycore-som: Fix mpu voltage
...
Add omap2_clk_enable_autoidle_all to am43xx_init_late otherwise the call
to omap2_clk_disable_autoidle_all in am43xx_init_early may cause some
clocks to always stay active and prevent low power mode transitions.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
OMAP5 SoC has Cortex-A15 which does not use TWD timer. It uses
ARCH_TIMER instead, clean up unwanted configuration and enable
OMAP_INTERCONNECT and OPP which is necessary for expected functionality
on the SoC.
Reported-by: Carlos Hernandez <ceh@ti.com>
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA7 does use OPP, uses OMAP interconnect and also does require SCU.
These are missing in the SoC only build of DRA7 breaking various PM
features in DRA7 only build.
Reported-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When commit c4082d499f ("ARM: omap2+: board-generic: clean up the
irq data from board file") cleaned up the direct usage of gic_of_init
and omap_intc_of_init, it failed to clean up the macros properly.
Since these macros are no longer used, lets just remove them.
Fixes: c4082d499f ("ARM: omap2+: board-generic: clean up the irq data from board file")
Reported-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP5 and DRA7 reuse the same pm44xx_erratum variable so, enable the
same, else PM features such as Suspend to ram is broken in a SoC only
build configuration.
Reported-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull ARM development updates from Russell King:
"Included in this update:
- moving PSCI code from ARM64/ARM to drivers/
- removal of some architecture internals from global kernel view
- addition of software based "privileged no access" support using the
old domains register to turn off the ability for kernel
loads/stores to access userspace. Only the proper accessors will
be usable.
- addition of early fixup support for early console
- re-addition (and reimplementation) of OMAP special interconnect
barrier
- removal of finish_arch_switch()
- only expose cpuX/online in sysfs if hotpluggable
- a number of code cleanups"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (41 commits)
ARM: software-based priviledged-no-access support
ARM: entry: provide uaccess assembly macro hooks
ARM: entry: get rid of multiple macro definitions
ARM: 8421/1: smp: Collapse arch_cpu_idle_dead() into cpu_die()
ARM: uaccess: provide uaccess_save_and_enable() and uaccess_restore()
ARM: mm: improve do_ldrd_abort macro
ARM: entry: ensure that IRQs are enabled when calling syscall_trace_exit()
ARM: entry: efficiency cleanups
ARM: entry: get rid of asm_trace_hardirqs_on_cond
ARM: uaccess: simplify user access assembly
ARM: domains: remove DOMAIN_TABLE
ARM: domains: keep vectors in separate domain
ARM: domains: get rid of manager mode for user domain
ARM: domains: move initial domain setting value to asm/domains.h
ARM: domains: provide domain_mask()
ARM: domains: switch to keeping domain value in register
ARM: 8419/1: dma-mapping: harmonize definition of DMA_ERROR_CODE
ARM: 8417/1: refactor bitops functions with BIT_MASK() and BIT_WORD()
ARM: 8416/1: Feroceon: use of_iomap() to map register base
ARM: 8415/1: early fixmap support for earlycon
...
ES2.0 is a minor variant of ES1.1. ES2.0 is an incremental revision
with various fixes including the following:
- reset logic fixes
- few assymetric aging logic fixes
- MMC clock rate fixes
- Ethernet speed fixes
- edma fixes for mcasp
NOTE: even though we use a compatible of dra742 and dra752, the usage in
the Linux kernel is more or less interchangable - we use dra752 more
often in the linux kernel compared to dra742 and 4.2-rc6
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the warning:
arch/arm/mach-omap2/vc.c:302:47: warning: logical ‘or’ of collectively exhaustive tests is always true [-Wlogical-op]
As we're toggling both CLKREQ and OFFMODE, we should also be checking
OFFMODE.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When bringing up a new SoC we needlessly prevent booting at timer
init if timer clock_set_parent fails. This can fail if the system
is booting on bootloader configured PLL values until the clock
framework driver for the PLL is implemented.
Let's just WARN instead, this will provide helpful information
for anybody bringing up a new SoC what needs to be fixed.
This allows to boot dm814x that's still missing the PLL driver.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- Cleanups for Renesas shmobile platforms
- Lots of added devices on LPC18xx
- Lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some branches
that are primarily merged through the clock tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=D2Pm
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Ladies and gentlemen, we proudly announce to you the latest branch of
ARM device tree contents for the mainline kernel. Come and see, come
and see!
No less than twentythree thousand lines of additions! Just imagine the
joy you will have of using your mainline kernel on newly supported
hardware such as Rockchip Chromebooks, Freescale i.MX6UL boards or
UniPhier hardware!
For those of you feeling less adventurous, added hardware support on
platforms such as TI DM814x and Gumstix Overo platforms might be more
of your liking.
We've got something for everyone here!
Ahem. Cough. So, anyway...
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- cleanups for Renesas shmobile platforms
- lots of added devices on LPC18xx
- lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some
branches that are primarily merged through the clock tree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (389 commits)
ARM: tegra: Add gpio-ranges property
ARM: tegra: Fix AHB base address on Tegra20, Tegra30 and Tegra114
ARM: tegra: Add Tegra124 PMU support
ARM: tegra: jetson-tk1: Add GK20A GPU DT node
ARM: tegra: venice2: Add GK20A GPU DT node
ARM: tegra: Add IOMMU node to GK20A
ARM: tegra: Add CPU regulator to the Jetson TK1 device tree
ARM: tegra: Add entries for cpufreq on Tegra124
ARM: tegra: Enable the DFLL on the Jetson TK1
ARM: tegra: Add the DFLL to Tegra124 device tree
ARM: dts: zynq: Add devicetree entry for Xilinx Zynq reset controller.
ARM: dts: UniPhier: fix PPI interrupt CPU mask of timer nodes
ARM: dts: rockchip: correct regulator power states for suspend
ARM: dts: rockchip: correct regulator PM properties
ARM: dts: vexpress: Use assigned-clock-parents for sp810
pinctrl: tegra: Only set the gpio range if needed
arm: boot: dts: am4372: add ARM timers and SCU nodes
ARM: dts: AM4372: Add the am4372-rtc compatible string
ARM: shmobile: r8a7794 dtsi: Add CPG/MSTP Clock Domain
ARM: shmobile: r8a7793 dtsi: Add CPG/MSTP Clock Domain
...
New or improved SoC support:
- Addition of support for Atmel's SAMA5D2 SoC
- Addition of Freescale i.MX6UL
- Improved support of TI's DM814x platform
- Misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch are
also here (acked by appropriate maintainers):
- Power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- Clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8T5Z
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"New or improved SoC support:
- add support for Atmel's SAMA5D2 SoC
- add support for Freescale i.MX6UL
- improved support for TI's DM814x platform
- misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch
are also here (acked by appropriate maintainers):
- power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: rockchip: pm: Fix PTR_ERR() argument
ARM: imx: mach-imx6ul: Fix allmodconfig build
clk: ti: fix for definition movement
ARM: uniphier: drop v7_invalidate_l1 call at secondary entry
memory: kill off set_irq_flags usage
rtc: snvs: select option REGMAP_MMIO
ARM: brcmstb: select ARCH_DMA_ADDR_T_64BIT for LPAE
ARM: BCM: Enable ARM erratum 798181 for BRCMSTB
ARM: OMAP2+: Fix power domain operations regression caused by 81xx
ARM: rockchip: enable PMU_GPIOINT_WAKEUP_EN when entering shallow suspend
ARM: rockchip: set correct stabilization thresholds in suspend
ARM: rockchip: rename osc_switch_to_32k variable
ARM: imx6ul: add fec MAC refrence clock and phy fixup init
ARM: imx6ul: add fec bits to GPR syscon definition
rtc: mxc: add support of device tree
dt-binding: document the binding for mxc rtc
rtc: mxc: use a second rtc clock
ARM: davinci: cp_intc: use IRQCHIP_SKIP_SET_WAKE instead of irq_set_wake callback
soc: mediatek: Fix SCPSYS compilation
ARM: at91/soc: add basic support for new sama5d2 SoC
...
A large cleanup branch this release, with a healthy 10k negative line delta.
Most of this is removal of legacy (non-DT) support of shmobile
platforms. There is also removal of two non-DT platforms on OMAP,
and the plat-samsung directory is cleaned out by moving most of the
previously shared-location-but-not-actually-shared files from there to
the appropriate mach directories instead.
There are other sets of changes in here as well:
- Rob Herring removed use of set_irq_flags under all platforms and
moved to genirq alternatives
- A series of timer API conversions to set-state interface
- ep93xx, nomadik and ux500 cleanups from Linus Walleij
- __init annotation fixes from Nicolas Pitre
+ a bunch of other changes that all add up to a nice set of cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=acy4
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"A large cleanup branch this release, with a healthy 10k negative line
delta.
Most of this is removal of legacy (non-DT) support of shmobile
platforms. There is also removal of two non-DT platforms on OMAP, and
the plat-samsung directory is cleaned out by moving most of the
previously shared-location-but-not-actually-shared files from there to
the appropriate mach directories instead.
There are other sets of changes in here as well:
- Rob Herring removed use of set_irq_flags under all platforms and
moved to genirq alternatives
- a series of timer API conversions to set-state interface
- ep93xx, nomadik and ux500 cleanups from Linus Walleij
- __init annotation fixes from Nicolas Pitre
+ a bunch of other changes that all add up to a nice set of cleanups"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (108 commits)
ARM/fb: ep93xx: switch framebuffer to use modedb only
ARM: gemini: Setup timer3 as free running timer
ARM: gemini: Use timer1 for clockevent
ARM: gemini: Add missing register definitions for gemini timer
ARM: ep93xx/timer: Migrate to new 'set-state' interface
ARM: nomadik: push accelerometer down to boards
ARM: nomadik: move l2x0 setup to device tree
ARM: nomadik: selectively enable UART0 on boards
ARM: nomadik: move hog code to use DT hogs
ARM: shmobile: Fix mismerges
ARM: ux500: simplify secondary CPU boot
ARM: SAMSUNG: remove keypad-core header in plat-samsung
ARM: SAMSUNG: local watchdog-reset header in mach-s3c64xx
ARM: SAMSUNG: local onenand-core header in mach-s3c64xx
ARM: SAMSUNG: local irq-uart header in mach-s3c64xx
ARM: SAMSUNG: local backlight header in mach-s3c64xx
ARM: SAMSUNG: local ata-core header in mach-s3c64xx
ARM: SAMSUNG: local regs-usb-hsotg-phy header in mach-s3c64xx
ARM: SAMSUNG: local spi-core header in mach-s3c24xx
ARM: SAMSUNG: local nand-core header in mach-s3c24xx
...
and the addition of new clock drivers. Stephen Boyd has also done a lot
of subsystem-wide driver clean-ups (thanks!). There are also fixes to
the framework core and changes to better split clock provider drivers
from clock consumer drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QAiQ
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Michael Turquette:
"The clk framework changes for 4.3 are mostly updates to existing
drivers and the addition of new clock drivers. Stephen Boyd has also
done a lot of subsystem-wide driver clean-ups (thanks!). There are
also fixes to the framework core and changes to better split clock
provider drivers from clock consumer drivers"
* tag 'clk-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (227 commits)
clk: s5pv210: add missing call to samsung_clk_of_add_provider()
clk: pistachio: correct critical clock list
clk: pistachio: Fix PLL rate calculation in integer mode
clk: pistachio: Fix override of clk-pll settings from boot loader
clk: pistachio: Fix 32bit integer overflows
clk: tegra: Fix some static checker problems
clk: qcom: Fix MSM8916 prng clock enable bit
clk: Add missing header for 'bool' definition to clk-conf.h
drivers/clk: appropriate __init annotation for const data
clk: rockchip: register pll mux before pll itself
clk: add bindings for the Ux500 clocks
clk/ARM: move Ux500 PRCC bases to the device tree
clk: remove duplicated code with __clk_set_parent_after
clk: Convert __clk_get_name(hw->clk) to clk_hw_get_name(hw)
clk: Constify clk_hw argument to provider APIs
clk: Hi6220: add stub clock driver
dt-bindings: clk: Hi6220: Document stub clock driver
dt-bindings: arm: Hi6220: add doc for SRAM controller
clk: atlas7: fix pll missed divide NR in fraction mode
clk: atlas7: fix bit field and its root clk for coresight_tpiu
...
We're removing struct clk from the clk provider API, so switch to
clk_get_rate() and clk_hw_get_rate() here appropriately.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The conversion of the wakeupgen irqchip to hierarchical irq domains
failed to provide a mechanism to properly set the trigger type of an
interrupt.
The wakeupgen irq chip itself has no mechanism and therefor no
irq_set_type() callback. The code before the conversion relayed the
trigger configuration directly to the underlying GIC.
Restore the correct behaviour by setting the wakeupgen irq_set_type
callback to irq_chip_set_type_parent(). This propagates the
set_trigger() call to the underlying GIC irqchip.
[ tglx: Massaged changelog ]
Fixes: 7136d457f3 ('ARM: omap: convert wakeupgen to stacked domains')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-5-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
I managed to mess up omap3 power domain operations with commit
7c80a3f89c ("ARM: OMAP2+: Add custom prwdm_operations for 81xx
to support dm814x"), by default we should keep on using the
omap3_pwrdm_operations, only 81xx needs custom handling.
This causes omap3 PM to break so we won't hit off mode any longer
causing idle power consumption go up from less than 10mW to over
50 mW.
Fixs: 7c80a3f89c ("ARM: OMAP2+: Add custom prwdm_operations for
81xx to support dm814x")
Signed-off-by: Tony Lindgren <tony@atomide.com>
* fixes: (28 commits)
ARM: ux500: add an SMP enablement type and move cpu nodes
ARM: dts: keystone: fix dt bindings to use post div register for mainpll
ARM: nomadik: disable UART0 on Nomadik boards
ARM: dts: i.MX35: Fix can support.
ARM: OMAP2+: hwmod: Fix _wait_target_ready() for hwmods without sysc
ARM: dts: add CPU OPP and regulator supply property for exynos4210
ARM: dts: Update video-phy node with syscon phandle for exynos3250
ARM: keystone: dts: rename pcie nodes to help override status
ARM: keystone: dts: fix dt bindings for PCIe
ARM: pxa: fix dm9000 platform data regression
ARM: DRA7: hwmod: fix gpmc hwmod
ARM: dts: Correct audio input route & set mic bias for am335x-pepper
ARM: OMAP2+: Add HAVE_ARM_SCU for AM43XX
MAINTAINERS: digicolor: add dts files
ARM: ux500: fix MMC/SD card regression
ARM: ux500: define serial port aliases
ARM: dts: OMAP5: Add #iommu-cells property to IOMMUs
ARM: dts: OMAP4: Add #iommu-cells property to IOMMUs
ARM: dts: Fix frequency scaling on Gumstix Pepper
ARM: dts: configure regulators for Gumstix Pepper
...
* cleanup-clk-h-includes: (62 commits)
clk: Remove clk.h from clk-provider.h
clk: h8300: Remove clk.h and clkdev.h includes
clk: at91: Include clk.h and slab.h
clk: ti: Switch clk-provider.h include to clk.h
clk: pistachio: Include clk.h
clk: ingenic: Include clk.h
clk: si570: Include clk.h
clk: moxart: Include clk.h
clk: cdce925: Include clk.h
clk: Include clk.h in clk.c
clk: zynq: Include clk.h
clk: ti: Include clk.h
clk: sunxi: Include clk.h and remove unused clkdev.h includes
clk: st: Include clk.h
clk: qcom: Include clk.h
clk: highbank: Include clk.h
clk: bcm: Include clk.h
clk: versatile: Remove clk.h and clkdev.h includes
clk: ux500: Remove clk.h and clkdev.h includes
clk: tegra: Properly include clk.h
...
From Tero Kristo:
"This pull request contains the TI clock driver set to move the
clock implementations under clock driver. Some small portions of
the clock driver code still remain under mach-omap2 after this,
it should be decided whether this code is now obsolete and should
be deleted or should someone try to fix it."
Slight merge conflicts with determine_rate prototype changes.
Init data marked const should be annotated with __initconst for
correctness and not __initdata. In some cases the array gathering
references to that data has to be marked const as well. This fixes
LTO builds that otherwise fail with section mismatch errors.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Clock rates are stored in an unsigned long field, but ->determine_rate()
(which returns a rounded rate from a requested one) returns a long
value (errors are reported using negative error codes), which can lead
to long overflow if the clock rate exceed 2Ghz.
Change ->determine_rate() prototype to return 0 or an error code, and pass
a pointer to a clk_rate_request structure containing the expected target
rate and the rate constraints imposed by clk users.
The clk_rate_request structure might be extended in the future to contain
other kind of constraints like the rounding policy, the maximum clock
inaccuracy or other things that are not yet supported by the CCF
(power consumption constraints ?).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Jonathan Corbet <corbet@lwn.net>
CC: Tony Lindgren <tony@atomide.com>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: "Emilio López" <emilio@elopez.com.ar>
CC: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
CC: Peter De Schrijver <pdeschrijver@nvidia.com>
CC: Prashant Gaikwad <pgaikwad@nvidia.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: linux-doc@vger.kernel.org
CC: linux-kernel@vger.kernel.org
CC: linux-arm-kernel@lists.infradead.org
CC: linux-omap@vger.kernel.org
CC: linux-mips@linux-mips.org
CC: linux-tegra@vger.kernel.org
[sboyd@codeaurora.org: Fix parent dereference problem in
__clk_determine_rate()]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[sboyd@codeaurora.org: Folded in fix from Heiko for fixed-rate
clocks without parents or a rate determining op]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Two fixes against v4.2-rc1. The first, for DRA7xx platforms,
corrects some incorrect GPMC hardware description data. The
second one will ensure that the hwmod code will wait for any
module with CPU-accessible registers to become ready before
attempting to access it.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.2-rc/20150723065408/
Note that I do not have a DRA7xx or AM43xx board, and therefore
cannot test on those platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dgbc
-----END PGP SIGNATURE-----
Merge tag 'for-v4.2-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
Merge "ARM: OMAP2+: hwmod fixes for v4.2-rc" from Paul Walmsley:
ARM: OMAP2+: hwmod fixes for v4.2-rc
Two fixes against v4.2-rc1. The first, for DRA7xx platforms,
corrects some incorrect GPMC hardware description data. The
second one will ensure that the hwmod code will wait for any
module with CPU-accessible registers to become ready before
attempting to access it.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.2-rc/20150723065408/
Note that I do not have a DRA7xx or AM43xx board, and therefore
cannot test on those platforms.
* tag 'for-v4.2-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP2+: hwmod: Fix _wait_target_ready() for hwmods without sysc
ARM: DRA7: hwmod: fix gpmc hwmod
Signed-off-by: Olof Johansson <olof@lixom.net>
Restore the OMAP4 barrier behaviour using the new implementation which
allows multiplatform systems to hook into the mb() and wmb() ARM
implementations to perform any necessary additional barrier maintanence.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 606da4826b.
We actually need this code for proper behaviour of OMAP4, and it needs
fixing a different way other than just removing the code. Disabling
code which is necessary in the hopes of persuing multiplatform kernels
is a stupid approach.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Similar to commit fdf4850cb5 ("ARM: BCM5301X: workaround suppress fault"),
let's add custom handling for the aborts on t410 that prevent booting:
Unhandled fault: imprecise external abort (0xc06) at 0xee091fb0
pgd = ee4bc000
[ee091fb0] *pgd=ae00041e(bad)
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000007
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's add minimal set of dm814x hwmods to have a bootable system.
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's change the defines so we can share the hwmod code better between
dm816x and dm814x, and let's add the dm814x specific defines. And let's
rename the shared ones to start with dm81xx. No functional changes.
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This series adds:
- I/O wakeup support for AM43xx
- register lock and unlock support to the hwmod code (needed for the RTC
IP blocks on some chips)
- several fixes for sparse warnings and an unnecessary null pointer test
- a DRA7xx clockdomain configuration workaround, to deal with some hardware
bugs
Basic build, boot, and PM tests are here:
http://www.pwsan.com/omap/testlogs/hwmod-prcm-for-v4.3/20150723080012/
Since I do not have an AM43xx or DRA7xx device, I can't test on those
platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dZvv
-----END PGP SIGNATURE-----
Merge tag 'for-v4.3/omap-hwmod-prcm-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.3/soc
ARM: OMAP2+: PRCM and hwmod changes for v4.3
This series adds:
- I/O wakeup support for AM43xx
- register lock and unlock support to the hwmod code (needed for the RTC
IP blocks on some chips)
- several fixes for sparse warnings and an unnecessary null pointer test
- a DRA7xx clockdomain configuration workaround, to deal with some hardware
bugs
Basic build, boot, and PM tests are here:
http://www.pwsan.com/omap/testlogs/hwmod-prcm-for-v4.3/20150723080012/
Since I do not have an AM43xx or DRA7xx device, I can't test on those
platforms.
Enable IO wakeup feature. This enables am437x pads to generate daisy
chained wake ups(eventually generates aprcm Interrupt) especially
when in low power modes.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The register offsets for some of the PRM Registers are different
hence populating the differing fields. This is needed to support
IO wake up feature for am437x family.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The register offsets of IRQENABLE_MPU_2 and IRQSTATUS_MPU_2 are hardcoded.
This makes it difficult to reuse the code for SoCs like AM437x that have
a single instance of IRQENABLE_MPU and IRQSTATUS_MPU registers.
Hence handling the case using offset of 4 to accommodate single set of IRQ*
registers generically.
Signed-off-by: Keerthy <j-keerthy@ti.com>
[paul@pwsan.com: fixed whitespace alignment problems reported by checkpatch.pl]
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the PRM IRQ register offsets. This is needed to support PRM I/O
wakeup on AM43xx.
Signed-off-by: Keerthy <j-keerthy@ti.com>
[paul@pwsan.com: improved patch description, moved the PRM_IO_PMCTRL macro
out of the CM section]
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
PRM_IO_PMCTRL_OFFSET need not be same for all SOCs hence
remove hardcoding and use the value provided by the omap_prcm_irq_setup
structure. This is done to support IO wakeup on am437x series.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
dropping the board files for omap3logic and omap3pandora.
The reason for dropping these now rather than later is that now
we can simply revert the patches in case of unexpected issues as
we are not dropping any platform data at this point.
This leaves us with only the following board-*.c files:
BOARD REASON NEEDED
board-ldp.c Still used in RMKs boot test system
board-rx51-*.c Needs /proc/atags support for user space
Once we have the n900 legacy user space issues sorted out for
/proc/atags and system_rev, we can drop the remaining two
board-*.c files. And then one merge window after that we can
drop the legacy booting support assuming no unexpected issues
are found.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3+Gh
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.3/legacy-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Merge "drop few more legacy boards for v4.3" from Tony Lindgren:
Drop more omap3 legacy board-*.c files for v4.3. This time we're
dropping the board files for omap3logic and omap3pandora.
The reason for dropping these now rather than later is that now
we can simply revert the patches in case of unexpected issues as
we are not dropping any platform data at this point.
This leaves us with only the following board-*.c files:
BOARD REASON NEEDED
board-ldp.c Still used in RMKs boot test system
board-rx51-*.c Needs /proc/atags support for user space
Once we have the n900 legacy user space issues sorted out for
/proc/atags and system_rev, we can drop the remaining two
board-*.c files. And then one merge window after that we can
drop the legacy booting support assuming no unexpected issues
are found.
* tag 'omap-for-v4.3/legacy-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove legacy booting support for Pandora
ARM: OMAP2+: Remove legacy booting support for LogicPD Torpedo
Signed-off-by: Olof Johansson <olof@lixom.net>
Add wl1251 support via pdata-quirks as it's driver lacks DT
support. MMC3 is marked disabled in DT so that MMC3 instance of
hsmmc driver is probed using platform data with special card init
callback.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add backlight support via pdata-quirks as it's driver lacks DT support.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These files use the consumer API, so include clk.h explicitly.
Acked-by: Tero Kristo <t-kristo@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Migrate omap2 driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
This board has support for device tree based booting, and we've been
printing warnings about the legacy booting being deprecated for a
few merge cycles now. Let's attempt to remove the legacy booting
for it.
The reason for removing the legacy booting support now rather than
later is we can simply revert this patch if necessary if we run
into some unexpected issues that are not trivial to fix for the
device tree based booting.
Cc: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's add a minimal clocks for dm814x to get it booted. This is
mostly a placeholder and relies on the PLLs being on from the
bootloader.
Note that the divider clocks work the same way as on dm816x and
am335x.
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looking at the TI kernel tree I noticed that dm81xx need custom
ti81xx_pwrdm_operations. Let's also change dm816x over to use them
as the registers are different for dm81xx compared to others.
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For now, let's just add the ones shared with dm816x.
The dm814x specific ones can be added as they are tested.
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP IOMMU driver has been adapted to the IOMMU framework
for a while now, and it no longer supports being built as a
module. Cleanup all the module related references both from
the code and in the build.
While at it, also relocate a comment around the initcall to
avoid a checkpatch strict warning about using a blank line
after function/struct/union/enum declarations.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA7 uses OMAP5 IO table at the moment. This is purely spurious since
the OMAP5 and DRA7 register maps are different in many aspects.
AM57xx/DRA7 TRM Reference: http://www.ti.com/lit/ug/spruhz6/spruhz6.pdf
NOTE: Most of the drivers are already doing ioremap, so, there should'nt
be any functional improvement involved here, other than making the
initial iotable more accurate.
Fixes: a3a9384a11 ("ARM: DRA7: Reuse io tables and add a new .init_early")
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Inspired by a patch from Felipe Balbi <balbi@ti.com>, we can
now get rid of most the code in omap4_local_timer_init.
Omap4 is now device tree only.. And we have not properly supported
omap4 ES1.0 revision for a really long time AFAIK.
Let's just remove all that code to simplify things. This assumes
we have arm,cortex-a9-twd-timer entry in the omap4.dtsi file, which
we do.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The of_node_put() function tests whether its argument is NULL and then
returns immediately if so. Furthermore, the kerneldoc for
of_node_put() explicitly supports passing in a NULL pointer as its
argument. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[paul@pwsan.com: dropped the omap_device.c and omap_hwmod.c changes for
now, edited the commit message accordingly and to note the documented
"contract"]
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
omap3xxx_restart() and omap44xx_restart() are global
functions declared in common.h. Include this file
in omap3-restart.c and omap4-restart.c to prevent
sparse warnings of type:
arch/arm/mach-omap2/omap4-restart.c:22:6: warning: symbol 'omap44xx_restart' was not declared. Should it be static?
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add missing static declaration for file local variables.
This fixes sparse warnings of type:
arch/arm/mach-omap2/omap_hwmod_81xx_data.c:491:26: warning: symbol 'dm81xx_alwon_l3_slow__gpmc' was not declared. Should it be static?
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some IP blocks like RTC, needs an additional setting for writing to its
registers. This is to prevent any spurious writes from changing the
register values.
This patch adds optional lock and unlock function pointers to
the IP block's hwmod data. These unlock and lock function pointers
are called by hwmod code before and after writing sysconfig registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[paul@pwsan.com: fixed indentation level to conform with the rest of the
structure members]
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
GPMC smart idle is not really broken but it does not support
smart idle with wakeup.
Fixes: 556708fe87 ("ARM: OMAP: DRA7: hwmod: Make gpmc software supervised as the smart idle is broken")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Legacy IPs like PWMSS, present under l4per2_7xx_clkdm, cannot support
smart-idle when its clock domain is in HW_AUTO on DRA7 SoCs. Hence,
program clock domain to SW_WKUP.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: <stable@vger.kernel.org>
CONFIG_HAVE_ARM_SCU only gets selected if CONFIG_SMP is selected in an OMAP
system, however AM43XX needs this option regardless of CONFIG_SMP and also
for an AM43XX only build as it is important for controlling power in the SoC.
Without this we cannot suspend the CPU for SoC suspend or cpuidle. The
ARM Cortex A9 needs SCU CPU Power Status bits to be set to off mode in order
for the PRCM to transition the MPU to low power modes.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use pdata-quirks to provide platform data required for reset
management during boot and shutdown of the wkup_m3 processor
on both the AM33xx and AM43xx SoCs. The WkupM3 remote processor
is used to implement and achieve low-power functionality on
the AM33xx & AM43xx SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
This board has support for device tree based booting, and we've been
printing warnings about the legacy booting being deprecated for a
few merge cycles now. Let's attempt to remove the legacy booting
for it.
The reason for removing the legacy booting support now rather than
later is we can simply revert this patch if necessary if we run
into some unexpected issues that are not trivial to fix for the
device tree based booting.
Cc: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- OMAP hwspinlock DT support from Suman Anna
- QCOM hwspinlock DT support from Bjorn Andersson
- a new CSR atlas7 hwspinlock driver from Wei Chen
- CSR atlas7 hwspinlock DT binding document from Wei Chen
- a tiny QCOM hwspinlock driver fix from Bjorn Andersson
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2HLz
-----END PGP SIGNATURE-----
Merge tag 'hwspinlock-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/hwspinlock
Pull hwspinlock updates from Ohad Ben-Cohen:
- hwspinlock core DT support from Suman Anna
- OMAP hwspinlock DT support from Suman Anna
- QCOM hwspinlock DT support from Bjorn Andersson
- a new CSR atlas7 hwspinlock driver from Wei Chen
- CSR atlas7 hwspinlock DT binding document from Wei Chen
- a tiny QCOM hwspinlock driver fix from Bjorn Andersson
* tag 'hwspinlock-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/hwspinlock:
hwspinlock: qcom: Correct msb in regmap_field
DT: hwspinlock: add the CSR atlas7 hwspinlock bindings document
hwspinlock: add a CSR atlas7 driver
hwspinlock: qcom: Add support for Qualcomm HW Mutex block
DT: hwspinlock: Add binding documentation for Qualcomm hwmutex
hwspinlock/omap: add support for dt nodes
Documentation: dt: add the omap hwspinlock bindings document
hwspinlock/core: add device tree support
Documentation: dt: add common bindings for hwspinlock
As usual, quite a few device-tree updates in ARM land. There was ome
minor churn in DTs due to relicensing under a dual-license, and lots
of little additions of new peripherals, features etc, but nothing
really exciting to call to your attention. Some higlights, focsuing
on support for new SoCs and boards:
- AT91: new boards: Overkiz, Acme Systems' Arietta G25
- tegra: HDA support
- bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS RT-AC87U
- mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
boards, DLink DNS-327L
- OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill SL50
- ARM: added support for Juno r1 board
- sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33, Mele A1000G
- imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
Gateworks GW5510, and aristainetos2 boards
- hisilicon: hi6220 SoC support; new boards: 96boards hikey
Conflicts: None
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wWIc
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Kevin Hilman:
"As usual, quite a few device-tree updates in ARM land. There was one
minor churn in DTs due to relicensing under a dual-license, and lots
of little additions of new peripherals, features etc, but nothing
really exciting to call to your attention. Some higlights, focsuing
on support for new SoCs and boards:
- AT91: new boards: Overkiz, Acme Systems' Arietta G25
- tegra: HDA support
- bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS
RT-AC87U
- mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
boards, DLink DNS-327L
- OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill
SL50
- ARM: added support for Juno r1 board
- sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33,
Mele A1000G
- imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
Gateworks GW5510, and aristainetos2 boards
- hisilicon: hi6220 SoC support; new boards: 96boards hikey"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (462 commits)
ARM: hisi: revert changes from hisi/hip04-dt branch
ARM: nomadik: set proper compatible for accelerometer
ARM64: juno: add GPIO keys
ARM: at91/dt: sama5d4: fix dma conf for aes, sha and tdes nodes
ARM: dts: Introduce STM32F429 MCU
ARM: socfpga: dts: enable ethernet for Arria10 devkit
ARM: dts: k2l: fix the netcp range size
ARM: dts: k2e: fix the netcp range size
ARM: dts: k2hk: fix the netcp range size
ARM: dts: k2l-evm: Add device bindings for netcp driver
ARM: dts: k2e-evm: Add device bindings for netcp driver
ARM: dts: k2hk-evm: Add device bindings for netcp driver
ARM: BCM5301X: Add DT for Asus RT-AC87U
ARM: BCM5301X: add IRQ numbers for PCIe controller
ARM: BCM5301X: add NAND flash chip description
arm64: dts: Add dts files for Hisilicon Hi6220 SoC
clk: hi6220: Document devicetree bindings for hi6220 clock
arm64: hi6220: Document devicetree bindings for Hisilicon hi6220 SoC
ARM: at91/dt: sama5d4ek: mci0 uses slot 0
ARM: at91/dt: kizbox: fix mismatch LED PWM device
...
Our SoC branch usually contains expanded support for new SoCs and
other core platform code. Some highlights from this round:
- sunxi: SMP support for A23 SoC
- socpga: big-endian support
- pxa: conversion to common clock framework
- bcm: SMP support for BCM63138
- imx: support new I.MX7D SoC
- zte: basic support for ZX296702 SoC
Conflicts:
arch/arm/mach-socfpga/core.h
Trivial remove/remove conflict with our cleanup branch.
Resolution: remove both sides
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZtPK
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform support updates from Kevin Hilman:
"Our SoC branch usually contains expanded support for new SoCs and
other core platform code. Some highlights from this round:
- sunxi: SMP support for A23 SoC
- socpga: big-endian support
- pxa: conversion to common clock framework
- bcm: SMP support for BCM63138
- imx: support new I.MX7D SoC
- zte: basic support for ZX296702 SoC"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (134 commits)
ARM: zx: Add basic defconfig support for ZX296702
ARM: dts: zx: add an initial zx296702 dts and doc
clk: zx: add clock support to zx296702
dt-bindings: Add #defines for ZTE ZX296702 clocks
ARM: socfpga: fix build error due to secondary_startup
MAINTAINERS: ARM64: EXYNOS: Extend entry for ARM64 DTS
ARM: ep93xx: simone: support for SPI-based MMC/SD cards
MAINTAINERS: update Shawn's email to use kernel.org one
ARM: socfpga: support suspend to ram
ARM: socfpga: add CPU_METHOD_OF_DECLARE for Arria 10
ARM: socfpga: use CPU_METHOD_OF_DECLARE for socfpga_cyclone5
ARM: EXYNOS: register power domain driver from core_initcall
ARM: EXYNOS: use PS_HOLD based poweroff for all supported SoCs
ARM: SAMSUNG: Constify platform_device_id
ARM: EXYNOS: Constify irq_domain_ops
ARM: EXYNOS: add coupled cpuidle support for Exynos3250
ARM: EXYNOS: add exynos_get_boot_addr() helper
ARM: EXYNOS: add exynos_set_boot_addr() helper
ARM: EXYNOS: make exynos_core_restart() less verbose
ARM: EXYNOS: fix exynos_boot_secondary() return value on timeout
...
A relatively small setup of cleanups this time around, and similar to last time
the bulk of it is removal of legacy board support:
- OMAP: removal of legacy (non-DT) booting for several platforms
- i.MX: remove some legacy board files
Conflicts: None
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0zof
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Kevin Hilman:
"A relatively small setup of cleanups this time around, and similar to
last time the bulk of it is removal of legacy board support:
- OMAP: removal of legacy (non-DT) booting for several platforms
- i.MX: remove some legacy board files"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (36 commits)
ARM: fix EFM32 build breakage caused by cpu_resume_arm
ARM: 8389/1: Add cpu_resume_arm() for firmwares that resume in ARM state
ARM: v7 setup function should invalidate L1 cache
mach-omap2: Remove use of deprecated marco, PTR_RET in devices.c
ARM: OMAP2+: Remove calls to deprecacted marco,PTR_RET in the files,fb.c and pmu.c
ARM: OMAP2+: Constify irq_domain_ops
ARM: OMAP2+: use symbolic defines for console loglevels instead of numbers
ARM: at91: remove useless Makefile.boot
ARM: at91: remove at91rm9200_sdramc.h
ARM: at91: remove mach/at91_ramc.h and mach/at91rm9200_mc.h
ARM: at91/pm: use the atmel-mc syscon defines
pcmcia: at91_cf: Use syscon to configure the MC/smc
ARM: at91: declare the at91rm9200 memory controller as a syscon
mfd: syscon: Add Atmel MC (Memory Controller) registers definition
ARM: at91: drop sam9_smc.c
ata: at91: use syscon to configure the smc
ARM: ux500: delete static resource defines
ARM: ux500: rename ux500_map_io
ARM: ux500: look up PRCMU resource from DT
ARM: ux500: kill off L2CC static map
...
Pull clkdev updates from Russell King:
"This series addresses some breakage in clkdev caused by a previous
patch set from the clk tree which introduced per-user clk structures.
This basically renamed the existing 'struct clk' to 'struct clk_hw',
and introduced a new 'struct clk'.
This change will break anyone using clk_add_alias() with the common
clk code enabled. Thankfully, the intersection of users of
clk_add_alias() and those using the common clk code is practically
zero, but this is something which should be fixed to keep the code
sane.
The problem is that clk_add_alias() does this:
r = clk_get(...);
l = clkdev_alloc(r, ...);
clk_put(...);
which causes the alias to store a pointer to 'r', which has been
freed.
The original patch set tried to work around this problem incorrectly -
at clk_get() time, it tried to convert the struct clk to a struct
clk_hw, and then creating a new struct clk from that. Clearly, if the
original struct clk has been freed, then we have a use-after-free bug.
We have other places in the tree which do something similar, so this
series also addresses those locations too.
This series addresses this problem by converting clkdev to store and
use the clk_hw pointer. This allows clk_get() to only have to create
it's per-user struct clk from the clk_hw. We can also get to the
desired clk_hw at clk_add_alias() or clk lookup creation time, when
the struct clk is "alive".
We also perform some cleanups of the code:
- replacing looped calls to clkdev_add() with clkdev_add_table()
- replacing open-coded lookup allocation (which should have been
using clkdev_alloc()) and subsequent clkdev_add() with
clkdev_create()
- replacing open-coded clk_add_alias() with clk_add_alias()"
* 'for-linus-clk' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
clk: s2mps11: use clkdev_create()
ASoC: migor: use clkdev_create()
ARM: omap2: use clkdev_add_alias()
ARM: omap2: use clkdev_create()
ARM: orion: use clkdev_create()
ARM: lpc32xx: convert to use clkdev_add_table()
SH: use clkdev_add_table()
clkdev: add clkdev_create() helper
clkdev: const-ify connection id to clk_add_alias()
clkdev: get rid of redundant clk_add_alias() prototype in linux/clk.h
clkdev: drop __init from clkdev_add_table()
clk: update clk API documentation to clarify clk_round_rate()
clkdev: use clk_hw internally
* pm-sleep:
PM / sleep: trace_device_pm_callback coverage in dpm_prepare/complete
PM / wakeup: add a dummy wakeup_source to record statistics
PM / sleep: Make suspend-to-idle-specific code depend on CONFIG_SUSPEND
PM / sleep: Return -EBUSY from suspend_enter() on wakeup detection
PM / tick: Add tracepoints for suspend-to-idle diagnostics
PM / sleep: Fix symbol name in a comment in kernel/power/main.c
leds / PM: fix hibernation on arm when gpio-led used with CPU led trigger
ARM: omap-device: use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
bus: omap_l3_noc: add missed callbacks for suspend-to-disk
PM / sleep: Add macro to define common noirq system PM callbacks
PM / sleep: Refine diagnostic messages in enter_state()
PM / wakeup: validate wakeup source before activating it.
* pm-runtime:
PM / Runtime: Update last_busy in rpm_resume
PM / runtime: add note about re-calling in during device probe()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVa7zvAAoJEHm+PkMAQRiGtfMIAILs3sxFtrC1hApgcfRLF/7z
K34bwTRqErzqUO/orTwakEr9kSIpIL0zIPSryTCOTPZLfMGkQjhHXO3KR/DSbbTV
MZ8y/BM/yelFA/Np+1LjbiYjTNRnTRvCoaQihkIH8Rn02g7ob9HyL4gIGKpuGFcZ
04GacL2cgChqsRSACdNef948jCoJXKgcuDpe39DXphDWZnBKNZ3HFuJ6bryGJf9A
1/eCI4is85BNwKPemQUYR0xx83UIzDfrghatZP2mOCDDSA2MNg8HNxLTd12LGoQD
tfgX4B7aftzW9Y7GSEDfZ0IKm2NRzgPmCVj6PjVR/iI0lIK4Aq0Z/lDJxxEq3XQ=
=AJM5
-----END PGP SIGNATURE-----
Merge tag 'v4.1-rc6' into next/dt
Linux 4.1-rc6
Conflicts:
arch/arm/boot/dts/zynq-7000.dtsi
Resolution summary:
Mainline had an earlier version of the commit, resolve in favor of the
newer patch in next/dt branch.
Simplify the DSS detection logic by creating a list of the omapdss
compat strings, instead of checking each separately with an 'if'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Set DSS core hwmod as the parent for all the DSS submodules. This
ensures that the parent hwmods are enabled before any DSS submodules are
accessed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Add DMM hwmod entries for DRA7. This is identical to DMM on OMAP5.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Add a new Linux clock for DRA7 based SoCs to control DESHDCP clock.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
With most of the clock code under clock driver already, the low-level
register access code, and the init code for the same, is no longer
needed outside the clock driver. Thus, these can be moved under clock
driver also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
As most of the clock driver code has migrated, these are no longer used
for anything. Thus remove these APIs completely.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
We should avoid exporting data from drivers, instead use an API for
registering the clock low level operations.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With legacy clock support gone, this is no longer needed under platform,
so move it under the clock driver itself. Make some exports be driver
internal definitions at the same time.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock data gone, this is no longer needed under platform,
so move it under the clock driver itself. Remove unnecessary declarations
from the TI clock header also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock data gone, this is no longer needed under platform,
so move it under the clock driver itself. Remove the exported clock driver
APIs as well, as these are not needed outside clock driver anymore.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, this is no longer needed under
platform code-base. Thus, move this under the TI clock driver, and
remove the exported API from the public header.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy support gone, OMAP2+ default gate clock can be moved
under clock driver. Create a new file for the purpose, and clean-up
the header exports a bit as some clock APIs are no longer needed
outside clock driver itself.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
clkdm_control is used to determine, whether clocks should trigger a
clockdomain transition when they are enabled/disabled. Keep this
functionality intact, but replace this with a clk_features flag
which can be initialized during boot if needed.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This now only has a couple of variables within it, which are used outside
the file itself. Move these variables to where they are actually used,
and remove the file completely as it is now empty.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, OMAP3 generic DPLL code can now be
moved over to the clock driver also. A few un-unused clkoutx2 functions
are also removed at the same time.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Clock driver requires access to some CM API functions once the code
is being moved under the clock driver from the platform directory.
Gate type clock requires access to cm_wait_module_ready and
cm_split_idlest_reg functions, which are both used for waiting until
the module being clocked has been successfully activated. These CM
APIs are now exported through the ti_clk_ll_ops struct.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Clock driver requires access to certain clockdomain handling ops once
the code is being moved over under clock driver. Example of this is
clk_enable / clk_disable under omap3 DPLL code. The required clkdm
APIs are now exported through the ti_clk_ll_ops struct.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The legacy support is wrong and dangerous, as it doesn't take any
OPPs into account and does not scale voltages. Switching mpurate should
be handled through cpufreq.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This is no longer used outside clock driver, so move it under the driver
and remove the export for it from the global header file.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This is no longer needed in platform directory, as the legacy clock data
is gone, so move it under TI clock driver. Some static functions are
renamed also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
These files contain legacy clock implementations which are no longer used
for anything, thus remove them completely.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This only contains clksel tables that were used with the legacy clock data.
Now that legacy clock data is completely gone, this file can be removed
also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The clksel clock type is no longer used for anything, it is rather
replaced with common clock divider code. Thus, remove the dead code
from kernel.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Core DVFS support code is currently referencing clksel functionality, which
is wrong. The m2 divisor has been implemented as a divider clock for a long
time already, so replace the validrate check call with proper functionality.
Core DVFS is currently not supported in the kernel so verifying this patch
can be rather tricky, this should probably be fixed at some point.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, the OMAP interface clock implementation
can be moved under the clock driver. Some temporary header file tweaks are
also needed to make this change work properly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, the OMAP4 specific DPLL implementations
can be moved under the clock driver. Change some of the function prototypes
to be static at the same time, and remove some exports from the global TI
clock driver header.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock data now gone, we can start moving OMAP clock
type implementations under clock driver. Start this with moving the
generic OMAP DPLL clock type under TI clock driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
As most of the clock driver support code is going to be moved under
drivers/clk/ti, an API for setting / getting the SoC specific clock
features is needed. This patch provides this API and changes the
existing code to use it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Register crypto hwmod links only if they are not disabled in DT.
If DT information is missing, enable them only for GP devices.
Before this patch crypto hwmod links were always disabled for all HS
devices and it was not possible to use omap-aes and omap-sham linux
drivers.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
[paul@pwsan.com: move the complex IP-block presence heuristics into their
own function to simplify the code; fix some checkpatch warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Without this patch function pm_runtime_get_sync() returns 0 even when
some omap subfunction fails. This patch properly propagate error codes
from omap functions back to caller.
This patch fix problem, when loading omap-aes driver in qemu cause
kernel oops.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
[paul@pwsan.com: fix a checkpatch warning]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Without a hwmod for am43xx emif use counting for emif clockdomain does
not happen correctly so it may be shut off by pm code unintentionally.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
We support decoding the bootloader values if DEBUG is defined.
But we also need to change the struct omap_hwmod flags to have
HWMOD_INIT_NO_RESET to avoid the GPMC being reset during the
boot. Otherwise just the default timings will be displayed
instead of the bootloader configured timings.
This also allows us to clean up the various GPMC related
hwmod flags. For debugging, we only need HWMOD_INIT_NO_RESET,
and HWMOD_INIT_NO_IDLE is not needed.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This removes the no longer required return statement at the end
of the void function, omap2_show_dma_cap due to no need for a
return statement due to this function always running successfully.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge cleanups from Russell King:
* 'for-arm-soc' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: Show proper respect for Heinrich Hertz by using the correct unit for frequency
- Configure MMC data lines 4..8 for 1.8V IO on boards that
are using them as GPIOs instead of MMC data lines
- Add support for Baltos IR5221
- Add device tree support for LogicPD Torpedo devkit
- Add 3717 core pinctrl region
- Add gta04 1w and GSM audio support
- Add wilink and ov2659 support for am437x-gp-evm
- Add am335x-evm bluetooth and mmc3 support
- Enable omap5-uevm uart wakeup interrupt
- Enable I2C2 on BeagleBone as it's used for the capes
- Use defines for LDP GPIO keys
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MmxV
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.2/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "Device tree related changes for omaps" from Tony Lindgren:
- Configure MMC data lines 4..8 for 1.8V IO on boards that
are using them as GPIOs instead of MMC data lines
- Add support for Baltos IR5221
- Add device tree support for LogicPD Torpedo devkit
- Add 3717 core pinctrl region
- Add gta04 1w and GSM audio support
- Add wilink and ov2659 support for am437x-gp-evm
- Add am335x-evm bluetooth and mmc3 support
- Enable omap5-uevm uart wakeup interrupt
- Enable I2C2 on BeagleBone as it's used for the capes
- Use defines for LDP GPIO keys
* tag 'omap-for-v4.2/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-evm: add mmc3 and wlan definitions to dts
ARM: dts: Enable SDIO card interrupt for 37xx-evm
ARM: dts: Fix ldp gpio keys to use defines
ARM: dts: Beaglebone i2c definitions
ARM: dts: am437x-gp-evm: add DT nodes for ov2659 sensor
ARM: dts: add DTS for Baltos IR5221
ARM: dts: omap5-uevm: Add Uart wakeup interrupt
ARM: dts: omap3-gta04: Add GSM audio support
ARM: dts: am335x-evm: add bluetooth support
ARM: dts: am437x-gp-evm: add wilink8 support
ARM: dts: omap3-gta04: Add hdqw1 support
ARM: dts: add core2 padconf region for am3517
ARM: dts: Add minimal support for LogicPD Torpedo DM3730 devkit
ARM: OMAP3: Add support for configuring MMC pins as GPIO pins
We get a NULL pointer dereference on omap3 for thumb2 compiled kernels:
Internal error: Oops: 80000005 [#1] SMP THUMB2
...
[<c046497b>] (_raw_spin_unlock_irqrestore) from [<c0024375>]
(omap3_enter_idle_bm+0xc5/0x178)
[<c0024375>] (omap3_enter_idle_bm) from [<c0374e63>]
(cpuidle_enter_state+0x77/0x27c)
[<c0374e63>] (cpuidle_enter_state) from [<c00627f1>]
(cpu_startup_entry+0x155/0x23c)
[<c00627f1>] (cpu_startup_entry) from [<c06b9a47>]
(start_kernel+0x32f/0x338)
[<c06b9a47>] (start_kernel) from [<8000807f>] (0x8000807f)
The power management related assembly on omaps needs to interact with
ARM mode bootrom code, so we need to keep most of the related assembly
in ARM mode.
Turns out this error is because of missing ENDPROC for assembly code
as suggested by Stephen Boyd <sboyd@codeaurora.org>. Let's fix the
problem by adding ENDPROC in two places to sleep34xx.S.
Let's also remove the now duplicate custom code for mode switching.
This has been unnecessary since commit 6ebbf2ce43 ("ARM: convert
all "mov.* pc, reg" to "bx reg" for ARMv6+").
And let's also remove the comments about local variables, they are
now just confusing after the ENDPROC.
The reason why ENDPROC makes a difference is it sets .type and then
the compiler knows what to do with the thumb bit as explained at:
https://wiki.ubuntu.com/ARM/Thumb2PortingHowto
Reported-by: Kevin Hilman <khilman@kernel.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Drop more omap3 legacy board-*.c files for v4.2. This time we're
dropping the board files for beagle, overo and cm-t35.
The reason for dropping these now rather than later is that now
we can simply revert the patches in case of unexpected issues as
we are not dropping any platform data at this point.
This leaves us with only the following board-*.c files:
BOARD REASON NEEDED
board-ldp.c Still used in RMKs boot test system
board-omap3logic.c Getting a .dts file for v4.2
board-omap3pandora.c Got a .dts file for v4.1
board-rx51-*.c Needs /proc/atags support for user space
I'm hoping we can drop the remaining board-*.c for v4.3 merge
window, then keep the platform data around for one more merge
window in case of reverting needed, then drop the platform data
too for v4.4 if no issues needing reverting are found.
Also, few patches to clean-up the usage of Linux generic
macros:
- Use define for console loglevel
- Use const for struct irq_domain_ops
- Use PTR_ERR_OR_ZERO instead of PTR_RET
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AVB2
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.2/clean' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Merge "Clean-up for omaps for v4.2 merge window" from Tony Lindgren:
Drop more omap3 legacy board-*.c files for v4.2. This time we're
dropping the board files for beagle, overo and cm-t35.
The reason for dropping these now rather than later is that now
we can simply revert the patches in case of unexpected issues as
we are not dropping any platform data at this point.
This leaves us with only the following board-*.c files:
BOARD REASON NEEDED
board-ldp.c Still used in RMKs boot test system
board-omap3logic.c Getting a .dts file for v4.2
board-omap3pandora.c Got a .dts file for v4.1
board-rx51-*.c Needs /proc/atags support for user space
I'm hoping we can drop the remaining board-*.c for v4.3 merge
window, then keep the platform data around for one more merge
window in case of reverting needed, then drop the platform data
too for v4.4 if no issues needing reverting are found.
Also, few patches to clean-up the usage of Linux generic
macros:
- Use define for console loglevel
- Use const for struct irq_domain_ops
- Use PTR_ERR_OR_ZERO instead of PTR_RET
* tag 'omap-for-v4.2/clean' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
mach-omap2: Remove use of deprecated marco, PTR_RET in devices.c
ARM: OMAP2+: Remove calls to deprecacted marco,PTR_RET in the files,fb.c and pmu.c
ARM: OMAP2+: Constify irq_domain_ops
ARM: OMAP2+: use symbolic defines for console loglevels instead of numbers
ARM: OMAP2+: Remove legacy booting support for Beagleboards
ARM: OMAP2+: Remove legacy booting support for Overo
ARM: OMAP2+: Remove legacy booting support for cm-t35
This removes the deprecacted marco, PTR_RET and changes the
functions that use this marco in their return statement to
instead use the non deprecacted function, PTR_ERR_OR_ZERO
for the file devices.c.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This removes two calls to the deprecated marco,PTR_RET in
the files,fb.c and pmu.c for the functions,omap_init_vrfb
and omap_init_pmu respectfully. Furthermore these are now
replaced by calling the correctly non deprecacted function,
PTR_ERR_OR_ZERO in both functions.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The irq_domain_ops are not modified by the driver and the irqdomain core
code accepts pointer to a const data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
<linux/printk.h> provides macros for console log level, let's use it
instead of numbers.
Signed-off-by: Alexander Kuleshov <kuleshovmail@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some devices are using the MMC1 pins 4..8 as GPIO pins, and in
this case they need to be configured for 1.8V IO voltage if not
done by the bootloader as otherwise some devices like smsc911x
won't work properly.
Let's also make sure this register is saved and restored for
idle.
Cc: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SI unit of frequency is Hertz, named after Heinrich Hertz, and is
given the symbol "Hz" to denote this. "hz" is not the unit of frequency,
and is in fact meaningless.
Fix arch/arm to correctly use "Hz", thereby acknowledging Heinrich Hertz'
contribution to the modern world.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use recently introduced macro SET_NOIRQ_SYSTEM_SLEEP_PM_OPS to
set up PM callbacks. This also fixes missed assignment of
.poweroff_noirq() callback.
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix a few AM43xx problems: add the VPFE hwmod data, which removes some
warnings; and fix the IP block hardreset implementation.
Basic build, boot, and PM test results are here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.1-rc/20150508130543/
Note that I do not have an AM43xx board in the testbed, and thus
cannot test on that platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jonz
-----END PGP SIGNATURE-----
Merge tag 'for-v4.1-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.1/fixes
ARM: OMAP2+: first set of hwmod fixes for v4.1-rc
Fix a few AM43xx problems: add the VPFE hwmod data, which removes some
warnings; and fix the IP block hardreset implementation.
Basic build, boot, and PM test results are here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.1-rc/20150508130543/
Note that I do not have an AM43xx board in the testbed, and thus
cannot test on that platform.
With recent changes to use determine_rate, the comparison of two
clocks won't work without clk_is_match that does __clk_get_hw
on the clocks first.
As we've been unconditionally already calling clk_set_parent
already because of the bogus comparison, let's just remove the
check as suggested by Stephen Boyd <sboyd@codeaurora.org>.
Cc: Michael Turquette <mturquette@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The reset code functionality is mostly a copy paste between OMAP4+ and
AM33xx+. Re-use the omap4 code where possible, and just keep the special
implementation for de-asserting the hardreset lines for AM33xx, as
AM33xx+ devices have slightly different register layouts compared to
OMAP4+. This patch also fixes the hardreset issues faced on AM43xx.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Dave Gerlach <d-gerlach@ti.com>
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
AM43xx has slightly different reset register layout compared to OMAP4+,
with varying status bit shifts and status register offsets. Current
code assumes static offsets and identical status / reset control bit
shifts, which is wrong. This patch adds PRM core support for passing
the actual implementations from hwmod code. AM43xx mappings will be fixed
in subsequent patch.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Dave Gerlach <d-gerlach@ti.com>
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds VPFE HWMOD data for AM43xx.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Benoit Parrot <bparrot@ti.com>
[paul@pwsan.com: updated to apply on v4.1-rc1]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tony Lindgren