Running iperf along with p2p traffic on both TX and RX side then
stop one side, then stop the other side, then start it up again,
eventually the STA gets into a mode that it can not pass data at
all.
A hardware workaround for invalid RSSI can make FIFO write pointer
to jump over read pointer, causing RX data corruption and repeated
DMA. Both TX and RX works fine when the workaround is disabled.
To replace the original hardware work around, software looks for
frames with post delimiter CRC error and mark the RSSI invalid so
that the upperlayer will not use the RSSI associated with this
frame. So disable the hardware workaround by updating the appropriate
registers.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RSSI reported by the RX descriptor requires little manipulation.
Manipulate and report the correct RSSI to the stack. This will
fix the improper signal levels reported by iwconfig iw dev wlanX
station dump. Also the Link Quality reported seems to be varying
(falls to zero also sometimes) when iperf is run from STA to AP.
Also use the default noise floor for now as the one reported
during the caliberation seems to be wrong.
The Signal and Link Quality before this patch (taken while TX is
in progress from STA to AP)
09:59:13.285428037 Link Quality=29/70 Signal level=-81 dBm
09:59:13.410660084 Link Quality=20/70 Signal level=-90 dBm
09:59:13.586864392 Link Quality=21/70 Signal level=-89 dBm
09:59:13.710296281 Link Quality=21/70 Signal level=-89 dBm
09:59:13.821683064 Link Quality=25/70 Signal level=-85 dBm
09:59:13.933402989 Link Quality=24/70 Signal level=-86 dBm
09:59:14.045839276 Link Quality=26/70 Signal level=-84 dBm
09:59:14.193926673 Link Quality=23/70 Signal level=-87 dBm
09:59:14.306230262 Link Quality=31/70 Signal level=-79 dBm
09:59:14.419459667 Link Quality=26/70 Signal level=-84 dBm
09:59:14.530711167 Link Quality=37/70 Signal level=-73 dBm
09:59:14.642593962 Link Quality=29/70 Signal level=-81 dBm
09:59:14.754361169 Link Quality=21/70 Signal level=-89 dBm
09:59:14.866217355 Link Quality=21/70 Signal level=-89 dBm
09:59:14.976963623 Link Quality=28/70 Signal level=-82 dBm
09:59:15.089149809 Link Quality=26/70 Signal level=-84 dBm
09:59:15.205039887 Link Quality=27/70 Signal level=-83 dBm
09:59:15.316368003 Link Quality=23/70 Signal level=-87 dBm
09:59:15.427684036 Link Quality=36/70 Signal level=-74 dBm
09:59:15.539756380 Link Quality=21/70 Signal level=-89 dBm
09:59:15.650549093 Link Quality=22/70 Signal level=-88 dBm
09:59:15.761171672 Link Quality=32/70 Signal level=-78 dBm
09:59:15.872793750 Link Quality=23/70 Signal level=-87 dBm
09:59:15.984421694 Link Quality=22/70 Signal level=-88 dBm
09:59:16.097315093 Link Quality=21/70 Signal level=-89 dBm
The link quality and signal level after this patch (take while
TX is in progress from STA to AP)
17:21:25.627848091 Link Quality=65/70 Signal level=-45 dBm
17:21:25.762805607 Link Quality=65/70 Signal level=-45 dBm
17:21:25.875521888 Link Quality=66/70 Signal level=-44 dBm
17:21:25.987468448 Link Quality=66/70 Signal level=-44 dBm
17:21:26.100628151 Link Quality=66/70 Signal level=-44 dBm
17:21:26.213129671 Link Quality=66/70 Signal level=-44 dBm
17:21:26.324923070 Link Quality=65/70 Signal level=-45 dBm
17:21:26.436831357 Link Quality=65/70 Signal level=-45 dBm
17:21:26.610356973 Link Quality=65/70 Signal level=-45 dBm
17:21:26.723340047 Link Quality=65/70 Signal level=-45 dBm
17:21:26.835715293 Link Quality=64/70 Signal level=-46 dBm
17:21:26.949542748 Link Quality=64/70 Signal level=-46 dBm
17:21:27.062261613 Link Quality=65/70 Signal level=-45 dBm
17:21:27.174511563 Link Quality=64/70 Signal level=-46 dBm
17:21:27.287616232 Link Quality=64/70 Signal level=-46 dBm
17:21:27.400598119 Link Quality=64/70 Signal level=-46 dBm
17:21:27.511381404 Link Quality=64/70 Signal level=-46 dBm
17:21:27.624530421 Link Quality=65/70 Signal level=-45 dBm
17:21:27.737807109 Link Quality=64/70 Signal level=-46 dBm
17:21:27.850861352 Link Quality=65/70 Signal level=-45 dBm
17:21:27.963369436 Link Quality=64/70 Signal level=-46 dBm
17:21:28.076582289 Link Quality=64/70 Signal level=-46 dBm
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move its only member (u8 per) to struct ath_rate_priv.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Get rid of rssi reduce interval.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k rate control is based on only PER (packet error rate),
remove unused code which was intented to do rssi based rate
selection.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the cleanup we just use get_rate as a wrapper, skip
the wrapper.
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All current rate control algorithms agree to send management and no-ack
frames at the lowest rate. They also agree to do this when sta
and the private rate control data is NULL. We add a hlper to mac80211
for this and simplify the rate control algorithm code.
Developers wishing to make enhancements to rate control algorithms
are for broadcast/multicast can opt to not use this in their
gate_rate() mac80211 callback.
Cc: Zhu Yi <yi.zhu@intel.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: ipw3945-devel@lists.sourceforge.net
Cc: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl-agn-rs.c already uses this.
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: ipw3945-devel@lists.sourceforge.net
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We check for this condition early on in our mac80211 get_rate()
callback ath_get_rate(), so remove this check later down the path.
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The purpose is to find the highest rate we can use.
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are a lot of gaps here.
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This saves us 2733 bytes.
text data bss dec hex filename
252265 3628 1584 257477 3edc5 ath9k-has-b-rate.ko
249905 3628 1584 255117 3e48d ath9k.ko
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Siged-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
What this does is get us our next lower rate so call it that,
ath_rc_get_lower_rix().
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is just calling another helper, so just use the other
helper directly. This should make it clear that when do not
find the next rate we stick to the current one.
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not used, remove this.
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not used, and when we need to get the lowest rate
we should simply use mac80211's own rate_lowest_index(sband, sta).
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has no functional change and just cleans up the code
to be more legible and removes a useless variable for
Multi Rate Retry.
For regular frames we use 2 retries for MRR segments [0-2].
For the last MRR segment [3] we use 4.
MRR[0] = 2
MRR[1] = 2
MRR[2] = 2
MRR[3] = 4
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the work around implemented for transmitting on
an unsupported band on iwlwifi. This was added via the patch:
8e1856e82cb8f541e925738bebfbc473420cda68:
iwlwifi: fix rs_get_rate WARN_ON()
Cc: Mohamed Abbas <mohamed.abbas@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The case where no vaid rate is found should not happen now
but to help debugging and downgrade this to a warn.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add omitted mutex_unlock to one of wl12xx_op_start fail paths (when
wl12xx_chip_wakeup fails).
[v2]
Power off the device, because:
\= cite from http://marc.info/?l=linux-kernel&m=124755028209880&w=2
If the chip cannot be booted, why should it remain powered on?
In some rare cases, the chip might fail to initialize, but can
recover if powered off and on again, so turning it off at this
point is the right thing to do. =/
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_dump_nic_error_log can be static and iwl_dump_nic_event_log
doesn't need to be exported.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding more detailed info about Asus motherboards and Ralink devices.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New device supported by the zd1211rw driver reported to linux-wireless.
Device string from lsusb:
"ID 083a:e501 Accton Technology Corp. ZD1211B"
RF type from dmesg:
zd1211b chip 083a:e501 v4810 high 00-1a-2a AL2230_RF pa0 g--NS
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Adrián Cereto<ssorgatem@esdebian.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The result of container_of should not be NULL. In particular, in this case
the argument to the enclosing function has passed though INIT_WORK, which
dereferences it, implying that its container cannot be NULL.
A simplified version of the semantic patch that makes this change is as
follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
identifier fn,work,x,fld;
type T;
expression E1,E2;
statement S;
@@
static fn(struct work_struct *work) {
... when != work = E1
x = container_of(work,T,fld)
... when != x = E2
- if (x == NULL) S
...
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The DEVICE_STATE_DISABLED_RADIO_HW flag is only read but never set,
it is an ancient part of one of the many versions of the rfkill implementations
in rt2x00. It is about time is disappears.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch roughly implements xmit aggregation for ar9170-like device.
Not all AP are compatible with the driver(and firmware) yet, so YMMV.
A more refined code will definitely need the final HT specification
to be available for the public, lots of firmware modification and
possibly a redesigned driver just for good measure.
Sadly, these conditions won't come true anytime soon...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enhances the eeprom parser to generate customized
channel list for every device.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement set_tim callback for all rt2x00 drivers, this makes the
device wake up powersaving stations properly while in AP mode.
The only way to update the beacon is by simply calling mac80211 and
requesting the new beacon. This means the set_tim() event is mostly the
same as a beacon_done() event which was already defined in rt2x00lib.
Signed-off-by: Stefan Steuerwald <salsasepp@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no reason to think that hwsim has any
actual signal strength, but for testing it is
very useful to have it report _some_ value to
the stack so I can see if the value ends up
being reported correctly
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to provide a reasonable minimum that will result in a
working setup if used. Set minimum to be 10 to provide for
4 standard TX queues + 1 command queue + 2 (unused) HCCA queues +
4 HT queues (one per AC).
We allow the user to change the number of queues used via a module
parameter and use this minimum value to check if it is valid. Without
this patch a user can select a value for the number of queues that
will result in a failing setup.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Rename maximum number of queue (TFD_QUEUE_MAX) to IWL39_NUM_QUEUES to
be consistent with rest of iwlwifi.
* Remove unused defines.
* Fix loops that iterate over number of TX queues to stop when maximum is reached
(currently it is maximum + 1).
* Remove queues_num module parameter as it is not used.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
debugfs files are created with 644 permissions which gives everybody
read access. This presents a security issue if a user opens the file and
holds it open at the time the driver removes the file. At this point
invalid memory will be accessed.
Fix this by only allowing root to read debugfs files.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This move the show_qos file from sysfs to debugfs because the "one
value per file" sysfs rule.
The file is located in
/sys/kernel/debug/ieee80211/phy0/iwlagn/data
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Different revisions of WUSB54GC-EU use different chipsets -
v2 uses rtl8187, but v3 uses Ralink RT3070.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Przemyslaw Kulczycki <azrael@autocom.pl>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Linux wireless <linux-wireless@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch re-enables p54's power save features and adds a workaround
which temporarily alters the device's power state in order to allow
ps-polls to be sent and buffered data to be retrieved during psm.
(Incorporates patch originally posted as "p54: fix beacon template dtim
IE corruption". -- JWL)
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By moving functions to before their first call, we eliminate
the need to define forward references.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A pointer to mac_sonic_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
Various other functions that are called by mac_sonic_probe need to move
to .devinit.text, too.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Jeff Garzik <jgarzik@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Tested-by: Finn Thain <fthain@telegraphics.com.au>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: netdev@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
A pointer to xtsonic_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Chris Zankel <chris@zankel.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
A pointer to sbmac_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Weiwei Wang <weiwei.wang@windriver.com>
Cc: Jeff Garzik <jgarzik@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
A pointer to meth_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: netdev@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
A pointer to jazz_sonic_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
As noticed by Geert Uytterhoeven sonic_probe1 is called by
jazz_sonic_probe, so the former has to move to .devinit.text, too.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: netdev@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
A pointer to sgiseeq_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Wang Chen <wangchen@cn.fujitsu.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jeff Garzik <jgarzik@redhat.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch zero's the timestamp before handing the packet to
the peer interface. This lets the peer recalculate the rx timestamp
if it cares about timestamps.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to the ems_pci driver for the new, v2,
4 channel CPC-PCI/PCIe/104P CAN cards from EMS Dr. Thomas Wuensche.
Signed-off-by: Sebastian Haas <haas@ems-wuensche.com>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Senthil Balasubramanian