Currently ar->flag maintains interface stats. Move interface
specific states from ar->flag to vif->flags.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is to avoid using ar->wdev to get wiphy pointer, this
may need further cleanup for multi vif support.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The new debugfs files keepalive and disconnect_timeout can be used to
fetch the current values and to change the values for keepalive and
disconnect event timeout (both in seconds).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Roaming mode can be changed by writing roam mode (default, bssbias, or
lock) to roam_mode. Forced roam can be requested by writing the BSSID
into force_roam.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The new roam_table debugfs file can be used to display the current
roam table from the target.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no use for these, at least right now, so better to remove them.
If some of them are ever needed, we can always add them back.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This allows RSN pre-authentication to be used when roaming decisions are
done in the target.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now that we allow the first Beacon frame after each connection to
be processed at the host, we can figure out the DTIM period and
expose it with Beacon interval through STA info BSS parameters
to user space.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since we may end up using a dummy BSS entry when roaming, allow one Beacon
frame -based bssinfo from the current BSS to be processed prior to starting
to filter all bssinfo events. This allows cfg80211 BSS table to be filled
with proper data in the roaming case where the full Beacon data may not
have been present at the time of roamed event.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is no point in unconditionally converting the bssinfo header
to the old version since only the new header is being used and the
driver can as well read the values from it when needed. Leaving out
the conversion saves some extra memory copying.
In addition, use the calculated "rssi" value snr - 95 dBm to get the
proper value in cfg80211 BSS table (i.e., something that more or less
matches with the value used in STA info).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now that the scan results are reported directly to the cfg80211 BSS
table there is no need for maintaining this internal node table
implementation for scan results. Remove the definitions and node
table functions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The internal node table in ath6kl was not really used for any useful
purpose. It was just used to collect scan results during a scan and then
provide them in a burst to cfg80211 at the completion of the scan. There
is no point in doing this since cfg80211 is perfectly capable of
maintaining the BSS table and the BSS inform messages are sent in
separate function calls anyway.
This provides more complete information in the cfg80211 BSS table since
this allows Beacon and Probe Response frames to be distinguished and IEs
from them reported separately.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This event has been deprecated and there is no need for ath6kl to
include code for processing it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Process the regulatory code from eeprom and pass the
country information to cfg80211.
kvalo: add space between struct name and *
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This cleans up the connect event parsing by defining a union in
struct wmi_connect_event to match with the three possible sets of
fields that the target uses depending on which type of connect
event is being indicated. In addition, two AP cases are now
separated from ath6kl_connect_event() so that correct field names
can be used to make it actually possible to understand what the
code is doing.
The bug hiding in the previous mess was in parsing the AID incorrectly
when processing the new station connecting event in AP mode. The fix
here for that is also fixing TIM updates for PS buffering to use the
correct AID.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is a 2-octet reserved field between the flag and aid fields. Fix
that to make the target actually behave as requested.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware initiates roaming only after it reaches a rssi of 20.
This lower rssi threshold can be modified through a wmi command
to modify the roaming behavior.
kvalo: rename debugfs functions and move comment about rssi units next to
ath6kl_wmi_set_roam_lrssi_cmd()
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware sends binary logs with WMIX_DBGLOG_EVENTID event. Create
a buffer which stores the latest logs and which can be copied from
fwlog debugfs file with cp command.
To save memory firmware log support is enabled only when CONFIG_ATH6KL_DEBUG
is enabled.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use WMI_TX_STATUS_EVENTID event to generate cfg80211_mgmt_tx_frame()
calls. Since we support only a single pending frame for now, use the
hardcoded cookie value 1 and store a copy of the pending frame in
the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Edward Lu <elu@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The target is not ready to accept addkey commands until the connect
event has been delivered, so delay these operations for the initial GTK.
In addition, properly set interface connected and mark netdev ready when
the AP mode setup has been completed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use cfg80211 add/del_beacon callbacks for starting/stopping AP mode and
set_beacon to update AP configuration (mainly, to update Beacon and
Probe Response IEs).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use wlan_iterate_nodes() directly.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
By having scan_table in struct ath6kl, it makes sense to move initialization
to ath6kl_init() and deinitialization to ath6kl_destroy().
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the bssid from ath6kl directly.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is nothing but bssid of struct ath6kl.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
And remove the reference to wmi in ath6kl_node_table.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Last May we started working on cleaning up ath6kl driver which is
currently in staging. The work has happened in a separate
ath6kl-cleanup tree:
http://git.kernel.org/?p=linux/kernel/git/kvalo/ath6kl-cleanup.git;a=summary
After over 1100 (!) patches we have now reached a state where I would
like to start discussing about pushing the driver to the wireless
trees and replacing the staging driver.
The driver is now a lot smaller and looks like a proper Linux driver.
The size of the driver (measured with simple wc -l) dropped from 49
kLOC to 18 kLOC and the number of the .c and .h files dropped from 107
to 22. Most importantly the number of subdirectories reduced from 26
to zero :)
There are two remaining checkpatch warnings in the driver which we
decided to omit for now:
drivers/net/wireless/ath/ath6kl/debug.c:31:
WARNING: printk() should include KERN_ facility level
drivers/net/wireless/ath/ath6kl/sdio.c:527:
WARNING: msleep < 20ms can sleep for up to 20ms;
see Documentation/timers/timers-howto.txt
The driver has endian annotations for all the hardware specific
structures and there are no sparse errors. Unfortunately I don't have
any big endian hardware to test that right now.
We have been testing the driver both on x86 and arm platforms. The
code is also compiled with sparc and parisc cross compilers.
Notable missing features compared to the current staging driver are:
o HCI over SDIO support
o nl80211 testmode
o firmware logging
o suspend support
Testmode, firmware logging and suspend support will be added soon. HCI
over SDIO support will be more difficult as the HCI driver needs to
share code with the wifi driver. This is something we need to research
more.
Also I want to point out the changes I did for signed endian support.
As I wasn't able to find any support for signed endian annotations I
decided to follow what NTFS has done and added my own. Grep for sle16
and sle32, especially from wmi.h.
Various people have been working on the cleanup, the hall of
fame based on number of patches is:
543 Vasanthakumar Thiagarajan
403 Raja Mani
252 Kalle Valo
16 Vivek Natarajan
12 Suraj Sumangala
3 Joe Perches
2 Jouni Malinen
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: Suraj Sumangala <surajs@qca.qualcomm.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Vasanthakumar Thiagarajan