We've never seen any device supported by the lm78 or w83781d driver at
addresses 0x20-0x27, so let's stop probing these addresses. Extra probes cost
time, and have potential for confusing or misdetecting other I2C devices.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
- add arcmsr_enable_eoi_mode()and readl(reg->iop2drv_doorbell_reg) in
arcmsr_handle_hbb_isr() on adapter Type B in case of the doorbell
interrupt clearance is cached
- add conditional declaration for arcmsr_pci_error_detected() and
arcmsr_pci_slot_reset
- check if the sg list member number exceeds arcmsr default limit in
arcmsr_build_ccb()
- change the returned value type of arcmsr_build_ccb()from "void" to
"int" returns FAILED in arcmsr_queue_command()
- modify arcmsr_drain_donequeue() to ignore unknown command and let
kernel process command timeout. This could handle IO request violating
maximum segments, i.e. Linux XFS over DM-CRYPT. Thanks to Milan Broz's
comments <mbroz@redhat.com>
- fix the release of dma memory for type B in arcmsr_free_ccb_pool()
- fix the arcmsr_polling_hbb_ccbdone()
Signed-off-by: Nick Cheng <nick.cheng@areca.com.tw>
Cc: Milan Broz <mbroz@redhat.com>
Cc: <thenzl@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This updates steeleye -> hansenpartnership in the documentation since
some email has been going astray because of this.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Add HP Jornada 6xx driver
leds: Remove the now uneeded ixp4xx driver
leds: Add power LED to the wrap driver
leds: Fix led-gpio active_low default brightness
leds: hw acceleration for Clevo mail LED driver
leds: Add support for hardware accelerated LED flashing
leds: Standardise LED naming scheme
leds: Add clevo notebook LED driver
(Old) mxser is obsoleted by mxser_new and scheduled for removal on Dec 2007.
Remove it by renaming mxser_new to mxser.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Reviewed-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the old iget() call and the read_inode() superblock operation it uses
as these are really obsolete, and the use of read_inode() does not produce
proper error handling (no distinction between ENOMEM and EIO when marking an
inode bad).
Furthermore, this removes the temptation to use iget() to find an inode by
number in a filesystem from code outside that filesystem.
iget_locked() should be used instead. A new function is added in an earlier
patch (iget_failed) that is to be called to mark an inode as bad, unlock it
and release it should the get routine fail. Mark iget() and read_inode() as
being obsolete and remove references to them from the documentation.
Typically a filesystem will be modified such that the read_inode function
becomes an internal iget function, for example the following:
void thingyfs_read_inode(struct inode *inode)
{
...
}
would be changed into something like:
struct inode *thingyfs_iget(struct super_block *sp, unsigned long ino)
{
struct inode *inode;
int ret;
inode = iget_locked(sb, ino);
if (!inode)
return ERR_PTR(-ENOMEM);
if (!(inode->i_state & I_NEW))
return inode;
...
unlock_new_inode(inode);
return inode;
error:
iget_failed(inode);
return ERR_PTR(ret);
}
and then thingyfs_iget() would be called rather than iget(), for example:
ret = -EINVAL;
inode = iget(sb, ino);
if (!inode || is_bad_inode(inode))
goto error;
becomes:
inode = thingyfs_iget(sb, ino);
if (IS_ERR(inode)) {
ret = PTR_ERR(inode);
goto error;
}
Note that is_bad_inode() does not need to be called. The error returned by
thingyfs_iget() should render it unnecessary.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce a function to register failure in an inode construction path. This
includes marking the inode under construction as bad, unlocking it and
releasing it.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update cpuset documentation to match the October 2007 "Fix cpusets
update_cpumask" changes that now apply changes to a cpusets 'cpus' allowed
mask immediately to the cpus_allowed of the tasks in that cpuset.
Signed-off-by: Paul Jackson <pj@sgi.com>
Acked-by: Cliff Wickman <cpw@sgi.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds a new sysctl, 'oom_dump_tasks', that enables the kernel to produce a
dump of all system tasks (excluding kernel threads) when performing an
OOM-killing. Information includes pid, uid, tgid, vm size, rss, cpu,
oom_adj score, and name.
This is helpful for determining why there was an OOM condition and which
rogue task caused it.
It is configurable so that large systems, such as those with several
thousand tasks, do not incur a performance penalty associated with dumping
data they may not desire.
If an OOM was triggered as a result of a memory controller, the tasklist
shall be filtered to exclude tasks that are not a member of the same
cgroup.
Cc: Andrea Arcangeli <andrea@suse.de>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the interface to use bytes instead of pages. Page sizes can vary
across platforms and configurations. A new strategy routine has been added
to the resource counters infrastructure to format the data as desired.
Suggested by David Rientjes, Andrew Morton and Herbert Poetzl
Tested on a UML setup with the config for memory control enabled.
[kamezawa.hiroyu@jp.fujitsu.com: possible race fix in res_counter]
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Cc: Paul Menage <menage@google.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Kirill Korotaev <dev@sw.ru>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: David Rientjes <rientjes@google.com>
Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the calls to the cgroup subsystem destroy() methods from
cgroup_rmdir() to cgroup_diput(). This allows control file reads and
writes to access their subsystem state without having to be concerned with
locking against cgroup destruction - the control file dentry will keep the
cgroup and its subsystem state objects alive until the file is closed.
The documentation is updated to reflect the changed semantics of destroy();
additionally the locking comments for destroy() and some other methods were
clarified and decrustified.
Signed-off-by: Paul Menage <menage@google.com>
Cc: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This comment is not helpful (no reason given) and is incorrect.
Just stick to facts that are useful regarding working on Linux.
(akpm: I've used sylpheed+imap for years)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The top-level Documentation/ directory is unmanageably large, so we
should take any obvious opportunities to move stuff into subdirectories.
These sched-*.txt files seem an obvious easy case.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This documentation is also vfs-related.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I'm inclined to think dnotify belongs in filesystems/.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's no reason for edac.txt for being at this unusual place.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Extends the leds subsystem with a blink_set() callback function which can
be optionally implemented by a LED driver. If implemented, the driver can use
the hardware acceleration for blinking a LED.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
As discussed on LKML some notion of 'function' is needed in
LED naming. This patch adds this to the documentation and
standardises existing LED drivers.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
The acpi_no_initrd_override parameter permits to disable the load of an ACPI
table from the initramfs.
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Len Brown <len.brown@intel.com>
See Documentation/ABI/testing/sysfs-firmware-acpi
Based-on-original-patch-by: Luming Yu <luming.yu@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
The basics of DSDT from initramfs. In case this option is selected,
populate_rootfs() is called a bit earlier to have the initramfs content
available during ACPI initialization.
This is a very similar path to the one available at
http://gaugusch.at/kernel.shtml but with some update in the
documentation, default set to No and the change of populate_rootfs() the
"Jeff Mahony way" (which avoids reading the initramfs twice).
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Docbook fatal error, file was moved:
docproc: linux-2.6.24-git15/drivers/base/dmapool.c: No such file or directory
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows userspace to control resync/reshape progress and synchronise it
with other activities, such as shared access in a SAN, or backing up critical
sections during a tricky reshape.
Writing a number of sectors (which must be a multiple of the chunk size if
such is meaningful) causes a resync to pause when it gets to that point.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert fb defio from nopage to fault.
Switch from OOM to SIGBUS if the resource is not available.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a GPIO 1-wire bus master driver. The driver used the GPIO API to
control the wire and the GPIO pin can be specified using platform data
similar to i2c-gpio. The driver was tested with AT91SAM9260 + DS2401.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No functional changes here, just tighten up style/whitespace.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Document the proper use of the irq_set_freq function.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide support to add an optional user defined callback to be run at
function entry of a kretprobe'd function. Also modify the kprobe smoke
tests to include an entry-handler during the kretprobe sanity test.
Signed-off-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Acked-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here's a couple of small additions to BUG-HUNTING.
1. point out that you can list code in gdb with only one command
(gdb) l *(<symbol> + offset)
2. give a very brief hint how to decode module symbols in call traces
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Just converting this documentation semaphore reference, since we don't
want to promote semaphore usage.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Acked-by: Corey Minyard <minyard@acm.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I converted some of the document to reflect mutex usage instead of
semaphore usage. Since we shouldin't be promoting semaphore usage when
it's on it's way out..
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here's a document I wrote after figuring out what unaligned memory access
is all about. I've tried to cover the information I was looking for when
trying to learn about this, without producing a hopelessly detailed/complex
spew. I hope it is useful to others.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Cc: Rob Landley <rob@landley.net>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jan Engelhardt <jengelh@computergmbh.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Kyle Moffett <mrmacman_g4@mac.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NR_OPEN (historically set to 1024*1024) actually forbids processes to open
more than 1024*1024 handles.
Unfortunatly some production servers hit the not so 'ridiculously high
value' of 1024*1024 file descriptors per process.
Changing NR_OPEN is not considered safe because of vmalloc space potential
exhaust.
This patch introduces a new sysctl (/proc/sys/fs/nr_open) wich defaults to
1024*1024, so that admins can decide to change this limit if their workload
needs it.
[akpm@linux-foundation.org: export it for sparc64]
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch contains the scheduled removal of OSS drivers whose config
options have been removed in 2.6.23.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ICAP device in Xilinx FPGAs differs slightly between different
FPGAs. The driver needs an additional attribute in the device tree to
distinguish this.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
with module_param macro, the __setup code can be killed now:
const __setup("all-generic-ide", ide_generic_all_on);
and the module name "generic.ko" is not descriptive to its functionality,
can be changed in Makefile, the "ide-pci-generic.ko" is better.
the ide-pci-generic.all-generic-ide parameter also documented
in Documentation/kernel-parameters.txt
Signed-off-by: Denis Cheng <crquan@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] make pfm_get_task work with virtual pids
[IA64] honor notify_die() returning NOTIFY_STOP
[IA64] remove dead code: __cpu_{down,die} from !HOTPLUG_CPU
[IA64] Appoint kvm/ia64 Maintainers
[IA64] ia64_set_psr should use srlz.i
[IA64] Export three symbols for module use
[IA64] mca style cleanup
[IA64] sn_hwperf semaphore to mutex
[IA64] generalize attribute of fsyscall_gtod_data
[IA64] efi.c Add /* never reached */ annotation
[IA64] efi.c Spelling/punctuation fixes
[IA64] Make efi.c mostly fit in 80 columns
[IA64] aliasing-test: fix gcc warnings on non-ia64
[IA64] Slim-down __clear_bit_unlock
[IA64] Fix the order of atomic operations in restore_previous_kprobes on ia64
[IA64] constify function pointer tables
[IA64] fix userspace compile error in gcc_intrin.h
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] dcss: Initialize workqueue before using it.
[S390] Remove BUILD_BUG_ON() in vmem code.
[S390] sclp_tty/sclp_vt220: Fix scheduling while atomic
[S390] dasd: fix panic caused by alias device offline
[S390] dasd: add ifcc handling
[S390] latencytop s390 support.
[S390] Implement ext2_find_next_bit.
[S390] Cleanup & optimize bitops.
[S390] Define GENERIC_LOCKBREAK.
[S390] console: allow vt220 console to be the only console
[S390] Fix couple of section mismatches.
[S390] Fix smp_call_function_mask semantics.
[S390] Fix linker script.
[S390] DEBUG_PAGEALLOC support for s390.
[S390] cio: Add shutdown callback for ccwgroup.
[S390] cio: Update documentation.
[S390] cio: Clean up chsc response code handling.
[S390] cio: make sense id procedure work with partial hardware response
The following patch is a generalization of the latency.c implementation done
by Arjan last year. It provides infrastructure for more than one parameter,
and exposes a user mode interface for processes to register pm_qos
expectations of processes.
This interface provides a kernel and user mode interface for registering
performance expectations by drivers, subsystems and user space applications on
one of the parameters.
Currently we have {cpu_dma_latency, network_latency, network_throughput} as
the initial set of pm_qos parameters.
The infrastructure exposes multiple misc device nodes one per implemented
parameter. The set of parameters implement is defined by pm_qos_power_init()
and pm_qos_params.h. This is done because having the available parameters
being runtime configurable or changeable from a driver was seen as too easy to
abuse.
For each parameter a list of performance requirements is maintained along with
an aggregated target value. The aggregated target value is updated with
changes to the requirement list or elements of the list. Typically the
aggregated target value is simply the max or min of the requirement values
held in the parameter list elements.
>From kernel mode the use of this interface is simple:
pm_qos_add_requirement(param_id, name, target_value):
Will insert a named element in the list for that identified PM_QOS
parameter with the target value. Upon change to this list the new target is
recomputed and any registered notifiers are called only if the target value
is now different.
pm_qos_update_requirement(param_id, name, new_target_value):
Will search the list identified by the param_id for the named list element
and then update its target value, calling the notification tree if the
aggregated target is changed. with that name is already registered.
pm_qos_remove_requirement(param_id, name):
Will search the identified list for the named element and remove it, after
removal it will update the aggregate target and call the notification tree
if the target was changed as a result of removing the named requirement.
>From user mode:
Only processes can register a pm_qos requirement. To provide for
automatic cleanup for process the interface requires the process to register
its parameter requirements in the following way:
To register the default pm_qos target for the specific parameter, the
process must open one of /dev/[cpu_dma_latency, network_latency,
network_throughput]
As long as the device node is held open that process has a registered
requirement on the parameter. The name of the requirement is
"process_<PID>" derived from the current->pid from within the open system
call.
To change the requested target value the process needs to write a s32
value to the open device node. This translates to a
pm_qos_update_requirement call.
To remove the user mode request for a target value simply close the device
node.
[akpm@linux-foundation.org: fix warnings]
[akpm@linux-foundation.org: fix build]
[akpm@linux-foundation.org: fix build again]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: mark gross <mgross@linux.intel.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Adam Belay <abelay@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Smack is the Simplified Mandatory Access Control Kernel.
Smack implements mandatory access control (MAC) using labels
attached to tasks and data containers, including files, SVIPC,
and other tasks. Smack is a kernel based scheme that requires
an absolute minimum of application support and a very small
amount of configuration data.
Smack uses extended attributes and
provides a set of general mount options, borrowing technics used
elsewhere. Smack uses netlabel for CIPSO labeling. Smack provides
a pseudo-filesystem smackfs that is used for manipulation of
system Smack attributes.
The patch, patches for ls and sshd, a README, a startup script,
and x86 binaries for ls and sshd are also available on
http://www.schaufler-ca.com
Development has been done using Fedora Core 7 in a virtual machine
environment and on an old Sony laptop.
Smack provides mandatory access controls based on the label attached
to a task and the label attached to the object it is attempting to
access. Smack labels are deliberately short (1-23 characters) text
strings. Single character labels using special characters are reserved
for system use. The only operation applied to Smack labels is equality
comparison. No wildcards or expressions, regular or otherwise, are
used. Smack labels are composed of printable characters and may not
include "/".
A file always gets the Smack label of the task that created it.
Smack defines and uses these labels:
"*" - pronounced "star"
"_" - pronounced "floor"
"^" - pronounced "hat"
"?" - pronounced "huh"
The access rules enforced by Smack are, in order:
1. Any access requested by a task labeled "*" is denied.
2. A read or execute access requested by a task labeled "^"
is permitted.
3. A read or execute access requested on an object labeled "_"
is permitted.
4. Any access requested on an object labeled "*" is permitted.
5. Any access requested by a task on an object with the same
label is permitted.
6. Any access requested that is explicitly defined in the loaded
rule set is permitted.
7. Any other access is denied.
Rules may be explicitly defined by writing subject,object,access
triples to /smack/load.
Smack rule sets can be easily defined that describe Bell&LaPadula
sensitivity, Biba integrity, and a variety of interesting
configurations. Smack rule sets can be modified on the fly to
accommodate changes in the operating environment or even the time
of day.
Some practical use cases:
Hierarchical levels. The less common of the two usual uses
for MLS systems is to define hierarchical levels, often
unclassified, confidential, secret, and so on. To set up smack
to support this, these rules could be defined:
C Unclass rx
S C rx
S Unclass rx
TS S rx
TS C rx
TS Unclass rx
A TS process can read S, C, and Unclass data, but cannot write it.
An S process can read C and Unclass. Note that specifying that
TS can read S and S can read C does not imply TS can read C, it
has to be explicitly stated.
Non-hierarchical categories. This is the more common of the
usual uses for an MLS system. Since the default rule is that a
subject cannot access an object with a different label no
access rules are required to implement compartmentalization.
A case that the Bell & LaPadula policy does not allow is demonstrated
with this Smack access rule:
A case that Bell&LaPadula does not allow that Smack does:
ESPN ABC r
ABC ESPN r
On my portable video device I have two applications, one that
shows ABC programming and the other ESPN programming. ESPN wants
to show me sport stories that show up as news, and ABC will
only provide minimal information about a sports story if ESPN
is covering it. Each side can look at the other's info, neither
can change the other. Neither can see what FOX is up to, which
is just as well all things considered.
Another case that I especially like:
SatData Guard w
Guard Publish w
A program running with the Guard label opens a UDP socket and
accepts messages sent by a program running with a SatData label.
The Guard program inspects the message to ensure it is wholesome
and if it is sends it to a program running with the Publish label.
This program then puts the information passed in an appropriate
place. Note that the Guard program cannot write to a Publish
file system object because file system semanitic require read as
well as write.
The four cases (categories, levels, mutual read, guardbox) here
are all quite real, and problems I've been asked to solve over
the years. The first two are easy to do with traditonal MLS systems
while the last two you can't without invoking privilege, at least
for a while.
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Cc: Joshua Brindle <method@manicmethod.com>
Cc: Paul Moore <paul.moore@hp.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: James Morris <jmorris@namei.org>
Cc: "Ahmed S. Darwish" <darwish.07@gmail.com>
Cc: Andrew G. Morgan <morgan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Though the lower_zone_protection was changed to lowmem_reserve_ratio, the
document has been not changed. The lowmem_reserve_ratio seems quite hard
to estimate, but there is no guidance. This patch is to change document
for it.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Andrea Arcangeli <andrea@cpushare.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add vm.highmem_is_dirtyable toggle
A 32 bit machine with HIGHMEM64 enabled running DCC has an MMAPed file of
approximately 2Gb size which contains a hash format that is written
randomly by the dbclean process. On 2.6.16 this process took a few
minutes. With lowmem only accounting of dirty ratios, this takes about 12
hours of 100% disk IO, all random writes.
Include a toggle in /proc/sys/vm/highmem_is_dirtyable which can be set to 1 to
add the highmem back to the total available memory count.
[akpm@linux-foundation.org: Fix the CONFIG_DETECT_SOFTLOCKUP=y build]
Signed-off-by: Bron Gondwana <brong@fastmail.fm>
Cc: Ethan Solomita <solo@google.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: WU Fengguang <wfg@mail.ustc.edu.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use drivers/gpio/pca9539.c instead.
Signed-off-by: eric miao <eric.miao@marvell.com>
Acked-by: Ben Gardner <bgardner@wabtec.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update Documentation/gpio.txt, primarily to include the new "gpiolib"
infrastructure.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove kio_addr_t, and replace it with unsigned int. No known architecture
needs more than 32 bits for IO addresses and ports and having a separate type
for it is just messy.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eliminate all build warnings. OK, these build warnings are from
a build on x86_64. When I build on ia64, I don't see warnings.
Now builds cleanly on ia64 and x86_64.
Documentation/ia64/aliasing-test.c: In function 'map_mem':
Documentation/ia64/aliasing-test.c:39: warning: implicit declaration of function 'ioctl'
Documentation/ia64/aliasing-test.c: In function 'scan_rom':
Documentation/ia64/aliasing-test.c:183: warning: format '%ld' expects type 'long int', but argument 4 has type 'int'
Documentation/ia64/aliasing-test.c: At top level:
Documentation/ia64/aliasing-test.c:208: warning: function declaration isn't a prototype
Documentation/ia64/aliasing-test.c: In function 'main':
Documentation/ia64/aliasing-test.c:259: warning: control reaches end of non-void function
Documentation/ia64/aliasing-test.c: In function 'scan_rom':
Documentation/ia64/aliasing-test.c:152: warning: 'rc' may be used uninitialized in this function
Documentation/ia64/aliasing-test.c: In function 'scan_tree':
Documentation/ia64/aliasing-test.c:68: warning: 'rc' may be used uninitialized in this function
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus: (25 commits)
virtio: balloon driver
virtio: Use PCI revision field to indicate virtio PCI ABI version
virtio: PCI device
virtio_blk: implement naming for vda-vdz,vdaa-vdzz,vdaaa-vdzzz
virtio_blk: Dont waste major numbers
virtio_blk: provide getgeo
virtio_net: parametrize the napi_weight for virtio receive queue.
virtio: free transmit skbs when notified, not on next xmit.
virtio: flush buffers on open
virtnet: remove double ether_setup
virtio: Allow virtio to be modular and used by modules
virtio: Use the sg_phys convenience function.
virtio: Put the virtio under the virtualization menu
virtio: handle interrupts after callbacks turned off
virtio: reset function
virtio: populate network rings in the probe routine, not open
virtio: Tweak virtio_net defines
virtio: Net header needs hdr_len
virtio: remove unused id field from struct virtio_blk_outhdr
virtio: clarify NO_NOTIFY flag usage
...
A reset function solves three problems:
1) It allows us to renegotiate features, eg. if we want to upgrade a
guest driver without rebooting the guest.
2) It gives us a clean way of shutting down virtqueues: after a reset,
we know that the buffers won't be used by the host, and
3) It helps the guest recover from messed-up drivers.
So we remove the ->shutdown hook, and the only way we now remove
feature bits is via reset.
We leave it to the driver to do the reset before it deletes queues:
the balloon driver, for example, needs to chat to the host in its
remove function.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The other side (host) can set the NO_NOTIFY flag as an optimization,
to say "no need to kick me when you add things". Make it clear that
this is advisory only; especially that we should always notify when
the ring is full.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Previously we used a type/len pair within the config space, but this
seems overkill. We now simply define a structure which represents the
layout in the config space: the config space can now only be extended
at the end.
The main driver-visible changes:
1) We indicate what fields are present with an explicit feature bit.
2) Virtqueues are explicitly numbered, and not in the config space.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
I was struggling to get my email-client no to mangle my patch files,
and I didn't find enough information in the SubmittingPatches file.
By looking for more information on the web, I eventually found the
email-clients.txt file, and it answered all my needs
This patch adds a reference to email-clients.txt in SubmittingPatches,
and Mozilla related information which is no longer accurate
(as opposed to the details found in email-clients.txt).
This should be helpful for people sending their first patches,
or not sending patches on a frequent basis.
Signed-off-by: Michael Opdenacker <michael@free-electrons.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Use the normal, expected mountpoint in the relay(fs) example
for debugfs.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Just a little whitespace cleanup patch for Documentation/BUG-HUNTING
Signed-off-by: Clemens Koller <clemens.koller@anagramm.de>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
My first guess for "fujitsu" was it might be related to the
fujitsu-laptop.c driver...
Move the frv directory one level up since frv is the name of the
architecture in the Linux kernel.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
After seeing the filename I'd have expected something about the
implementation of SMP in the Linux kernel - not some notes on kernel
configuration and building trivialities noone would search at this
place.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
This is a documentation followup to 2e591bbc0d
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Contents are reviewed by Japanese translation community called "JF".
Thanks a lot!
Singed-off-by: Tsugikazu Shibata <tshibata@ab.jp.nec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.infradead.org/battery-2.6:
apm_power: check I.intval for zero value, we use it as the divisor
MAINTAINERS: remove kernel-discuss@handhelds.org list
pda_power: implement polling
pda_power: various cleanups
apm_power: support using VOLTAGE_* properties for apm calculations
pda_power: add suspend/resume support
power_supply: add few more values and props
pda_power: only register available psu
power: fix incorrect unregistration in power_supply_create_attrs error path
power: remove POWER_SUPPLY_PROP_CAPACITY_LEVEL
[BATTERY] power_supply_leds: use kasprintf
[BATTERY] Every file should include the headers containing the prototypes for its global functions.
The Generic Thermal sysfs driver for thermal management.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Thomas Sujith <sujith.thomas@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'suspend' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (38 commits)
suspend: cleanup reference to swsusp_pg_dir[]
PM: Remove obsolete /sys/devices/.../power/state docs
Hibernation: Invoke suspend notifications after console switch
Suspend: Invoke suspend notifications after console switch
Suspend: Clean up suspend_64.c
Suspend: Add config option to disable the freezer if architecture wants that
ACPI: Print message before calling _PTS
ACPI hibernation: Call _PTS before suspending devices
Hibernation: Introduce begin() and end() callbacks
ACPI suspend: Call _PTS before suspending devices
ACPI: Separate disabling of GPEs from _PTS
ACPI: Separate invocations of _GTS and _BFS from _PTS and _WAK
Suspend: Introduce begin() and end() callbacks
suspend: fix ia64 allmodconfig build
ACPI: clear GPE earily in resume to avoid warning
Suspend: Clean up Kconfig (V2)
Hibernation: Clean up Kconfig (V2)
Hibernation: Update messages
Suspend: Use common prefix in messages
Hibernation: Remove unnecessary variable declaration
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6: (64 commits)
PCI: make pci_bus a struct device
PCI: fix codingstyle issues in include/linux/pci.h
PCI: fix codingstyle issues in drivers/pci/pci.h
PCI: PCIE ASPM support
PCI: Fix fakephp deadlock
PCI: modify SB700 SATA MSI quirk
PCI: Run ACPI _OSC method on root bridges only
PCI ACPI: AER driver should only register PCIe devices with _OSC
PCI ACPI: Added a function to register _OSC with only PCIe devices.
PCI: constify function pointer tables
PCI: Convert drivers/pci/proc.c to use unlocked_ioctl
pciehp: block new requests from the device before power off
pciehp: workaround against Bad DLLP during power off
pciehp: wait for 1000ms before LED operation after power off
PCI: Remove pci_enable_device_bars() from documentation
PCI: Remove pci_enable_device_bars()
PCI: Remove users of pci_enable_device_bars()
PCI: Add pci_enable_device_{io,mem} intefaces
PCI: avoid save the same type of cap multiple times
PCI: correctly initialize a structure for pcie_save_pcix_state()
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (128 commits)
USB: fix codingstyle issues in drivers/usb/core/*.c
USB: fix codingstyle issues in drivers/usb/core/message.c
USB: fix codingstyle issues in drivers/usb/core/hcd-pci.c
USB: fix codingstyle issues in drivers/usb/core/devio.c
USB: fix codingstyle issues in drivers/usb/core/devices.c
USB: fix codingstyle issues in drivers/usb/core/*.h
USB: fix codingstyle issues in include/linux/usb/
USB: fix codingstyle issues in include/linux/usb.h
USB: mark USB drivers as being GPL only
USB: use a real vendor and product id for root hubs
USB: mount options: fix usbfs
USB: Fix usb_serial_driver structure for Kobil cardreader driver.
usb: ehci should use u16 for isochronous intervals
usb: ehci, remove false clear-reset path
USB: Use menuconfig objects
usb: ohci-sm501 driver
usb: dma bounce buffer support
USB: last abuses of intfdata in close for usb-serial drivers
USB: kl5kusb105 don't flush to logically disconnected devices
USB: oti6858: cleanup
...
The major code reorganization and cleanups, and new HKEY events, plus
poll()/select() support are good reasons to checkpoint a new version...
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
Implement poll()/select() support through sysfs_notify() for some key
attributes which userspace might want to poll() or select() on.
In order to let userspace know poll()/select() support is available for an
attribute, the thinkpad-acpi sysfs interface version is also bumped up.
Further changes that add poll()/select() capabilities to any pre-existing
attributes will also increment the sysfs interface version.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
Tomas Carnecky reports that events 0x5009 and 0x500a are swivel events, and
that 0x500b/0x500c are tablet pen storage bay events.
Document these events, and avoid nasty messages when they happen.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
Handle some HKEY events that the firmware uses to report the reason for a
wake up, and to also notify that the system could go back to sleep (if it
woke up just to eject something from the bay, or to undock).
The driver will report the reason of the last wake up in the sysfs
attribute "wakeup_reason": 0 for "none, unknown, or standard ACPI wake up
event", 1 for "bay ejection request" and 2 for "undock request".
The firmware will also report if the operation that triggered the wake up
has been completed, by issuing an HKEY 0x3003 or 0x4003 event. If the
operation fails, no event is sent. When such a hotunplug sucessfull
notification is issued, the driver sets the attribute
"wakeup_hotunplug_complete" to 1.
While the firmware does tell us whether we are waking from a suspend or
hibernation scenario, the Linux way of hibernating makes this information
not reliable, and therefore it is not reported.
The idea is that if any of these attributes are non-zero, userspace might
want to do something at the end of the "wake up from sleep" procedures,
such as offering to send the machine back into sleep as soon as it is safe
to do so.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
Use a generic message on hotkey_notify to log unknown and unhandled events,
and cleanup hotkey_notify a little.
Also, document event 0x5010 (brightness changed notification) and do not
log it as an unknown event (even if we do not use it for anything right
now).
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
The NVRAM polling support for hot keys is reason enough to
bump up the version string. Do it.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
Older ThinkPad models do not export some of the hot keys over the
event-based ACPI hot key interface. For these models, one has to poll
the CMOS NVRAM to check the key state at a rate faster than the expected
rate at which the user might repeatedly press the same hot key.
This patch implements this functionality for many of the hotkeys in a
transparent way: hot keys will now Just Work, and the driver knows the
best approach (events or NVRAM polling) to employ, based on the
HKEY.MHKA ACPI method.
Also, the driver can turn off the polling when there are no users for
the hot keys that need such polling.
The NVRAM-based hot keys of the A3x series that have never been
implemented by later models are not supported, to avoid changes in the
keymap of the input devices that could cause headaches in the future.
There is a Kconfig option to avoid compiling the NVRAM polling code, as
it is not very small, and unlikely to be useful on any ThinkPad newer
than a T40, X31 or R52.
This feature is based on a previous effort by Richard Hughes.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Richard Hughes <hughsient@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add LiMn (one of the most common for small non-rechargable batteries)
battery technology and voltage_min/_max properties support.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Anton Vorontsov <cbou@mail.ru>
The CAPACITY_LEVEL stuff defines various levels of charge; however, what
is the difference between them? What differentiates between HIGH and NORMAL,
LOW and CRITICAL, etc?
As it appears that these are fairly arbitrary, we end up making such policy
decisions in the kernel (or in hardware). This is the sort of decision that
should be made in userspace, not in the kernel.
If the hardware does not support _CAPACITY and it cannot be easily calculated,
then perhaps the driver should register a custom CAPACITY_LEVEL attribute;
however, userspace should not become accustomed to looking for such a thing,
and we should certainly not encourage drivers to provide CAPACITY_LEVEL
stubs.
The following removes support for POWER_SUPPLY_PROP_CAPACITY_LEVEL. The
OLPC battery driver is the only driver making use of this, so it's
removed from there as well.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The /sys/devices/.../power/state files have been gone for a while
now, but I just noticed some documentation that still refers to
them. (Fortunately described as DEPRECATED and WILL REMOVE).
Time to remove that obsolete documentation too ...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
The ACPI 1.0 specification wants us to put devices into low power
states after executing the _PTS global control method, while ACPI
2.0 and later want us to do that in the reverse order. The current
suspend code follows ACPI 2.0 in that respect which causes some
ACPI 1.0x systems to hang during suspend (ref.
http://bugzilla.kernel.org/show_bug.cgi?id=9528).
Make the suspend code execute _PTS before putting devices into low
power states (ie. in accordance with ACPI 1.0x) and provide a command
line option to override the default if need be.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Update the suspend/hibernation debugging and testing documentation to describe
the newly introduced testing facilities.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Add PM_RESTORE_PREPARE and PM_POST_RESTORE notifiers to the PM core, to be used
in analogy with the existing PM_HIBERNATION_PREPARE and PM_POST_HIBERNATION
notifiers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Move the definitions of hibernation ioctls to a separate header file in
include/linux, which can be exported to the user space.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Three ioctl numbers belonging to the hibernation userland interface,
SNAPSHOT_ATOMIC_SNAPSHOT, SNAPSHOT_AVAIL_SWAP, SNAPSHOT_GET_SWAP_PAGE,
are defined in a wrong way (eg. not portable). Provide new ioctl numbers for
these ioctls and mark the existing ones as deprecated.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Mark the SNAPSHOT_SET_SWAP_FILE ioctl belonging to the hibernation userland
interface as deprecated.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Modify the hibernation userland interface by adding two new ioctls to it,
SNAPSHOT_PLATFORM_SUPPORT and SNAPSHOT_POWER_OFF, that can be used,
respectively, to switch the hibernation platform support on/off and to make the
kernel transition the system to the hibernation state (eg. ACPI S4) using the
platform (eg. ACPI) driver.
These ioctls are intended to replace the misdesigned SNAPSHOT_PMOPS ioctl,
which from now is regarded as obsolete and will be removed in the future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Add a new ioctl, SNAPSHOT_GET_IMAGE_SIZE, returning the size of the (just
created) hibernation image, to the hibernation userland interface.
This ioctl is necessary so that the userland utilities using the interface need
not access the hibernation image header, owned by the kernel, in order to obtain
the size of the image.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (100 commits)
ide: move hwif_register() call out of ide_probe_port()
ide: factor out code for tuning devices from ide_probe_port()
ide: move handling of I/O resources out of ide_probe_port()
ide: make probe_hwif() return an error value
ide: use ide_remove_port_from_hwgroup in init_irq()
ide: prepare init_irq() for using ide_remove_port_from_hwgroup()
ide: factor out code removing port from hwgroup from ide_unregister()
ide: I/O resources are released too early in ide_unregister()
ide: cleanup ide_system_bus_speed()
ide: remove needless zeroing of hwgroup fields from init_irq()
ide: remove unused ide_hwgroup_t fields
ide_platform: remove struct hwif_prop
ide: remove hwif->present manipulations from hwif_init()
ide: move wait_hwif_ready() documentation in the right place
ide: fix handling of busy I/O resources in probe_hwif()
<linux/hdsmart.h> is not used by kernel code
ide: don't include <linux/hdsmart.h>
ide-floppy: cleanup header
ide: update/add my Copyrights
ide: delete filenames/versions from comments
...
Over two years ago, the Linux USB developers stated that they believed
there was no way to create a USB kernel driver that was not under the
GPL. This patch moves the USB apis to enforce that decision.
There are no known closed source USB drivers in the wild, so this patch
should cause no problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This documents two newly created files:
/sys/bus/usb/device/.../power/connected_duration
/sys/bus/usb/device/.../power/active_duration
Documentation was placed in Documentation/ABI/testing, since that's where the
documentation is for the other USB sysfs power files.
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
G_PRINTER: Adds a USB printer gadget driver for use in printer firmware.
This adds a USB printer gadget driver for use in printer firmware.
The printer gadget channels data between the USB host and a userspace
program driving the print engine. The user space program reads and
writes the device file /dev/g_printer to receive or send printer data.
It can use ioctl calls to the device file to get or set printer status.
Signed-off-by: Craig W. Nadler <craig@nadler.us>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
execve arguments can be quite large. There is no limit on the number of
arguments and a 4G limit on the size of an argument.
this patch prints those aruguments in bite sized pieces. a userspace size
limitation of 8k was discovered so this keeps messages around 7.5k
single arguments larger than 7.5k in length are split into multiple records
and can be identified as aX[Y]=
Signed-off-by: Eric Paris <eparis@redhat.com>
Fix docbook fatal error (files were renamed):
docproc: linux-2.6.24-git9/arch/ppc/kernel/rio.c: No such file or directory
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
o Outbound sequence number overflow error status
is counted as XfrmOutStateSeqError.
o Additionaly, it changes inbound sequence number replay
error name from XfrmInSeqOutOfWindow to XfrmInStateSeqError
to apply name scheme above.
o Inbound IPv4 UDP encapsuling type mismatch error is wrongly
mapped to XfrmInStateInvalid then this patch fiex the error
to XfrmInStateMismatch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current ip route cache implementation is not suited to large caches.
We can consume a lot of CPU when cache must be invalidated, since we
currently need to evict all cache entries, and this eviction is
sometimes asynchronous. min_delay & max_delay can somewhat control this
asynchronism behavior, but whole thing is a kludge, regularly triggering
infamous soft lockup messages. When entries are still in use, this also
consumes a lot of ram, filling dst_garbage.list.
A better scheme is to use a generation identifier on each entry,
so that cache invalidation can be performed by changing the table
identifier, without having to scan all entries.
No more delayed flushing, no more stalling when secret_interval expires.
Invalidated entries will then be freed at GC time (controled by
ip_rt_gc_timeout or stress), or when an invalidated entry is found
in a chain when an insert is done.
Thus we keep a normal equilibrium.
This patch :
- renames rt_hash_rnd to rt_genid (and makes it an atomic_t)
- Adds a new rt_genid field to 'struct rtable' (filling a hole on 64bit)
- Checks entry->rt_genid at appropriate places :
Added the support for Dell T3400 with AD1984 codec chip.
ALSA bug#3699:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3699
Signed-off-by: Douglas Kosovic <douglask@itee.uq.edu.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the support for Conexant 5051 audio codec.
Right now there are two preset models, laptop and hp.
The whole patch is based on the information from the base patch by
Linuxant.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add a driver for the MediaTek/TempoTec HiFier Fantasia sound card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Update the ASoC documentation. Along with minor formatting and grammar
cleanups it moves the ASoC overview into the present tense to reflect
the fact that it has now been merged.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Change laptop models to three different models, laptop-hpsense,
laptop-micsense and laptop-hpmicsense. The first two correspond to
the old 'laptop' and 'fujitsu' models.
Reassigned the quirk table for the new models.
Signed-off-by: Marc Boucher <marc@linuxant.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The TempoTec HiFier has a somwhat different architecture; remove it from
the list of cards that are known to be supported.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add documentation entries for snd-oxygen and snd-virtuoso.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The benq r55e laptop have 3 jacks on the front panel.
One for HP, one for Line In and one for Mic In.
This patch implemented a new model to support it.
Signed-off-by: Jiang Zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the description of the model fujitsu for Cx5045 codec chip.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the support of Dell OEM laptops (Vostro 1200) with ALC268 codec.
The new model=dell is provided.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch fixes 5.1 surround output and headphone detection in the
Dell Inspiron 530 and possibly other Dell systems using the ALC888
codec (mode 6stack-dell).
Signed-off-by: Claudio Matsuoka <cmatsuoka@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
1. Support HP rp5700
2. Fixed alc_subsystem_id function (Bug fixed and support Desktop)
3. Support ASUS EP20
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This header file exists only for some hacks to adapt alsa-driver
tree. It's useless for building in the kernel. Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it. This should be really killed in
future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The xfer_align sw_params parameter has never been used in a sane manner,
and no one understands what this does exactly. The current
implementation looks also buggy because it allows write of shorter size
than xfer_align. So, if you do partial writes, the write isn't actually
aligned at all.
Removing this parameter will make some pcm_lib_* code more readable
(and less buggy).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This implements a test model for the ALC268. It depends on the feature
added by alc260-test-eapd-0.2.diff. This patch also adds a mention of
the ALC260 test model to ALSA-Configuration.txt since this seems to have
been missed.
Signed-off-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
It turned out that there can be multiple HD-audio devices on a single
machine (e.g. on-board audio and HDMI on graphic cards), so we need to
support multiple devices with snd-hda-intel driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The attached patch adds initial support of the Mitac 8252D
(http://www.mitac-mtc.com.tw/English/products/8252Dspec.htm).
Working:
- Front speakers (volume + mute)
- Center/LFE speakers (volume + mute)
- HP out (with Front Volume)
- HP individual mute switch
- HP Jack sense
- Front Mic and its volume
Not tested:
- external mic and its volume
Not working while now:
- Mic Jack sense
Questionable:
- is Mic have Jack sense?
- one or two Mic volume controls?
- CD/Line-in: presense in the mixer
Signed-off-by: Andy Shevchenko <andy@smile.org.ua>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This removes the pnp_resource_change use from the ALSA ISAPnP drivers. In
2.4 these were useful in providing an easy path to setting the resources,
but in 2.6 they retain function as a layering violation only.
This makes for a nice cleanup (-550 lines) of ALSA but moreover, ALSA is the
only remaining user of pnp_init_resource_table(), pnp_resource_change() and
pnp_manual_config_dev() (and, in fact, of 'struct pnp_resource_table') in
the tree outide of drivers/pnp itself meaning it makes for more cleanup
potential inside the PnP layer.
Thomas Renninger acked their removal from that side, you did from the ALSA
side (CC list just copied from that thread).
Against current alsa-kernel HG. Many more potential cleanups in there, but
this _only_ removes the pnp_resource_change code. Compile tested against
current alsa-kernel HG and compile- and use-tested against 2.6.23.x (few
offsets).
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the missing model string for the new support of HP TC T5735.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Introduced the global 'slots' option to snd module. This option provides
an alternative way to handle the order of multiple sound card instances.
It's an easier approach to avoid conflict with hotplug devices, and can
be used together with the existing 'order' option of each card driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds full record and playback support for the Samsung Q1
Ultra - Vista model (different codec than the earlier Q1 Ultra models).
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch brings some English style improvements throughout the
document, as well as 1 or 2 extra technical details.
Signed-off-by: Michael Opdenacker <michael@free-electrons.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the support for Onkyo SE-90PCI and SE-200PCI boards.
Signed-off-by: Shin-ya Okada <sh_okada at d4.dion.ne.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the missing model string 'eeepc-p701' for ALC662 codec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus: (27 commits)
lguest: use __PAGE_KERNEL instead of _PAGE_KERNEL
lguest: Use explicit includes rateher than indirect
lguest: get rid of lg variable assignments
lguest: change gpte_addr header
lguest: move changed bitmap to lg_cpu
lguest: move last_pages to lg_cpu
lguest: change last_guest to last_cpu
lguest: change spte_addr header
lguest: per-vcpu lguest pgdir management
lguest: make pending notifications per-vcpu
lguest: makes special fields be per-vcpu
lguest: per-vcpu lguest task management
lguest: replace lguest_arch with lg_cpu_arch.
lguest: make registers per-vcpu
lguest: make emulate_insn receive a vcpu struct.
lguest: map_switcher_in_guest() per-vcpu
lguest: per-vcpu interrupt processing.
lguest: per-vcpu lguest timers
lguest: make hypercalls use the vcpu struct
lguest: make write() operation smp aware
...
Manual conflict resolved (maybe even correctly, who knows) in
drivers/lguest/x86/core.c
Fix docbook fatal error:
docproc: linux-2.6.24-git8/block/ll_rw_blk.c: No such file or directory
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a new configuration option, which adds support for a new
early_param which gets checked in arch/x86/kernel/setup_{32,64}.c:setup_arch()
to decide wether OHCI-1394 FireWire controllers should be initialized and
enabled for physical DMA access to allow remote debugging of early problems
like issues ACPI or other subsystems which are executed very early.
If the config option is not enabled, no code is changed, and if the boot
paramenter is not given, no new code is executed, and independent of that,
all new code is freed after boot, so the config option can be even enabled
in standard, non-debug kernels.
With specialized tools, it is then possible to get debugging information
from machines which have no serial ports (notebooks) such as the printk
buffer contents, or any data which can be referenced from global pointers,
if it is stored below the 4GB limit and even memory dumps of of the physical
RAM region below the 4GB limit can be taken without any cooperation from the
CPU of the host, so the machine can be crashed early, it does not matter.
In the extreme, even kernel debuggers can be accessed in this way. I wrote
a small kgdb module and an accompanying gdb stub for FireWire which allows
to gdb to talk to kgdb using remote remory reads and writes over FireWire.
An version of the gdb stub fore FireWire is able to read all global data
from a system which is running a a normal kernel without any kernel debugger,
without any interruption or support of the system's CPU. That way, e.g. the
task struct and so on can be read and even manipulated when the physical DMA
access is granted.
A HOWTO is included in this patch, in Documentation/debugging-via-ohci1394.txt
and I've put a copy online at
ftp://ftp.suse.de/private/bk/firewire/docs/debugging-via-ohci1394.txt
It also has links to all the tools which are available to make use of it
another copy of it is online at:
ftp://ftp.suse.de/private/bk/firewire/kernel/ohci1394_dma_early-v2.diff
Signed-Off-By: Bernhard Kaindl <bk@suse.de>
Tested-By: Thomas Renninger <trenn@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The new "mfgptfix" boot command line option may be usd to fix MFGPT
timers on AMD Geode platforms when the BIOS has incorrectly applied
a workaround. TinyBIOS version 0.98 is known to be affected, 0.99
fixes the problem by letting the user disable the workaround.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
when MTRRs are not covering the whole e820 table, we need to trim the
RAM and need to update e820.
reuse some code on 64-bit as well.
here need to add early_get_cap and use it in early_cpu_detect, and move
mtrr_bp_init early.
The code successfully trimmed the memory map on Justin's system:
from:
[ 0.000000] BIOS-e820: 0000000100000000 - 000000022c000000 (usable)
to:
[ 0.000000] modified: 0000000100000000 - 0000000228000000 (usable)
[ 0.000000] modified: 0000000228000000 - 000000022c000000 (reserved)
According to Justin it makes quite a difference:
| When I boot the box without any trimming it acts like a 286 or 386,
| takes about 10 minutes to boot (using raptor disks).
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Tested-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add a generic option to clear any cpuid bit. I added it because it was
very easy to add with the new generic cpuid disable bitmap and perhaps
it will be useful in the future.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To disable CLFLUSH usage, especially in change_page_attr().
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On some machines, buggy BIOSes don't properly setup WB MTRRs to cover all
available RAM, meaning the last few megs (or even gigs) of memory will be
marked uncached. Since Linux tends to allocate from high memory addresses
first, this causes the machine to be unusably slow as soon as the kernel
starts really using memory (i.e. right around init time).
This patch works around the problem by scanning the MTRRs at boot and
figuring out whether the current end_pfn value (setup by early e820 code)
goes beyond the highest WB MTRR range, and if so, trimming it to match. A
fairly obnoxious KERN_WARNING is printed too, letting the user know that
not all of their memory is available due to a likely BIOS bug.
Something similar could be done on i386 if needed, but the boot ordering
would be slightly different, since the MTRR code on i386 depends on the
boot_cpu_data structure being setup.
This patch fixes a bug in the last patch that caused the code to run on
non-Intel machines (AMD machines apparently don't need it and it's untested
on other non-Intel machines, so best keep it off).
Further enhancements and fixes from:
Yinghai Lu <Yinghai.Lu@Sun.COM>
Andi Kleen <ak@suse.de>
Signed-off-by: Jesse Barnes <jesse.barnes@intel.com>
Tested-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
For K8 system: 4G RAM with memory hole remapping enabled, or more than
4G RAM installed.
when try to use kexec second kernel, and the first doesn't include
gart_shutdown. the second kernel could have different aper position than
the first kernel. and second kernel could use that hole as RAM that is
still used by GART set by the first kernel. esp. when try to kexec
2.6.24 with sparse mem enable from previous kernel (from RHEL 5 or SLES
10). the new kernel will use aper by GART (set by first kernel) for
vmemmap. and after new kernel setting one new GART. the position will be
real RAM. the _mapcount set is lost.
Bad page state in process 'swapper'
page:ffffe2000e600020 flags:0x0000000000000000 mapping:0000000000000000 mapcount:1 count:0
Trying to fix it up, but a reboot is needed
Backtrace:
Pid: 0, comm: swapper Not tainted 2.6.24-rc7-smp-gcdf71a10-dirty #13
Call Trace:
[<ffffffff8026401f>] bad_page+0x63/0x8d
[<ffffffff80264169>] __free_pages_ok+0x7c/0x2a5
[<ffffffff80ba75d1>] free_all_bootmem_core+0xd0/0x198
[<ffffffff80ba3a42>] numa_free_all_bootmem+0x3b/0x76
[<ffffffff80ba3461>] mem_init+0x3b/0x152
[<ffffffff80b959d3>] start_kernel+0x236/0x2c2
[<ffffffff80b9511a>] _sinittext+0x11a/0x121
and
[ffffe2000e600000-ffffe2000e7fffff] PMD ->ffff81001c200000 on node 0
phys addr is : 0x1c200000
RHEL 5.1 kernel -53 said:
PCI-DMA: aperture base @ 1c000000 size 65536 KB
new kernel said:
Mapping aperture over 65536 KB of RAM @ 3c000000
So could try to disable that GART if possible.
According to Ingo
> hm, i'm wondering, instead of modifying the GART, why dont we simply
> _detect_ whatever GART settings we have inherited, and propagate that
> into our e820 maps? I.e. if there's inconsistency, then punch that out
> from the memory maps and just dont use that memory.
>
> that way it would not matter whether the GART settings came from a [old
> or crashing] Linux kernel that has not called gart_iommu_shutdown(), or
> whether it's a BIOS that has set up an aperture hole inconsistent with
> the memory map it passed. (or the memory map we _think_ i tried to pass
> us)
>
> it would also be more robust to only read and do a memory map quirk
> based on that, than actively trying to change the GART so early in the
> bootup. Later on we have to re-enable the GART _anyway_ and have to
> punch a hole for it.
>
> and as a bonus, we would have shored up our defenses against crappy
> BIOSes as well.
add e820 modification for gart inconsistent setting.
gart_fix_e820=off could be used to disable e820 fix.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The 32 bit x86 tree has a very useful feature that prints the Code: line
for the code even before the trapping instrution (and the start of the
trapping instruction is then denoted with a <>). Unfortunately, the 64 bit
x86 tree does not yet have this feature, making diagnosing backtraces harder
than needed.
This patch adds this feature in the same was as the 32 bit tree has
(including the same kernel boot parameter), and including a bugfix
to make the code use probe_kernel_address() rarther than a buggy (deadlocking)
__get_user.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
support according to fixes of x86_64 support.
- Delete efi_rt_lock because it is used during system early boot,
before SMP is initialized.
- Change local_flush_tlb() to __flush_tlb_all() to flush global page
mapping.
- Clean up includes.
- Revise Kconfig description.
- Enable noefi kernel parameter on i386.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add the ability to reboot an x86_64 based machine using the RESET_REG in the
FADT ACPI table.
Signed-off-by: Aaron Durbin <adurbin@google.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This makes x86_64's ia32 emulation support share the sources used in the
32-bit kernel for the 32-bit vDSO and much of its setup code.
The 32-bit vDSO mapping now behaves the same on x86_64 as on native 32-bit.
The abi.syscall32 sysctl on x86_64 now takes the same values that
vm.vdso_enabled takes on the 32-bit kernel. That is, 1 means a randomized
vDSO location, 2 means the fixed old address. The CONFIG_COMPAT_VDSO
option is now available to make this the default setting, the same meaning
it has for the 32-bit kernel. (This does not affect the 64-bit vDSO.)
The argument vdso32=[012] can be used on both 32-bit and 64-bit kernels to
set this paramter at boot time. The vdso=[012] argument still does this
same thing on the 32-bit kernel.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
various changes to the in_p/out_p delay details:
- add the io_delay=none method
- make each method selectable from the kernel config
- simplify the delay code a bit by getting rid of an indirect function call
- add the /proc/sys/kernel/io_delay_type sysctl
- change 'io_delay=standard|alternate' to io_delay=0x80 and io_delay=0xed
- make the io delay config not depend on CONFIG_DEBUG_KERNEL
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: "David P. Reed" <dpreed@reed.com>
x86: provide a DMI based port 0x80 I/O delay override.
Certain (HP) laptops experience trouble from our port 0x80 I/O delay
writes. This patch provides for a DMI based switch to the "alternate
diagnostic port" 0xed (as used by some BIOSes as well) for these.
David P. Reed confirmed that port 0xed works for him and provides a
proper delay. The symptoms of _not_ working are a hanging machine,
with "hwclock" use being a direct trigger.
Earlier versions of this attempted to simply use udelay(2), with the
2 being a value tested to be a nicely conservative upper-bound with
help from many on the linux-kernel mailinglist but that approach has
two problems.
First, pre-loops_per_jiffy calibration (which is post PIT init while
some implementations of the PIT are actually one of the historically
problematic devices that need the delay) udelay() isn't particularly
well-defined. We could initialise loops_per_jiffy conservatively (and
based on CPU family so as to not unduly delay old machines) which
would sort of work, but...
Second, delaying isn't the only effect that a write to port 0x80 has.
It's also a PCI posting barrier which some devices may be explicitly
or implicitly relying on. Alan Cox did a survey and found evidence
that additionally some drivers may be racy on SMP without the bus
locking outb.
Switching to an inb() makes the timing too unpredictable and as such,
this DMI based switch should be the safest approach for now. Any more
invasive changes should get more rigid testing first. It's moreover
only very few machines with the problem and a DMI based hack seems
to fit that situation.
This also introduces a command-line parameter "io_delay" to override
the DMI based choice again:
io_delay=<standard|alternate>
where "standard" means using the standard port 0x80 and "alternate"
port 0xed.
This retains the udelay method as a config (CONFIG_UDELAY_IO_DELAY) and
command-line ("io_delay=udelay") choice for testing purposes as well.
This does not change the io_delay() in the boot code which is using
the same port 0x80 I/O delay but those do not appear to be a problem
as David P. Reed reported the problem was already gone after using the
udelay version. He moreover reported that booting with "acpi=off" also
fixed things and seeing as how ACPI isn't touched until after this DMI
based I/O port switch I believe it's safe to leave the ones in the boot
code be.
The DMI strings from David's HP Pavilion dv9000z are in there already
and we need to get/verify the DMI info from other machines with the
problem, notably the HP Pavilion dv6000z.
This patch is partly based on earlier patches from Pavel Machek and
David P. Reed.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch makes uses of pread() and pwrite() in lguest launcher
to communicate the vcpu id to the lguest driver. The id is kept in
a thread variable, which means we'll span in the future, vcpus as
threads. But right now, only the infrastructure is out there.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6.25: (1470 commits)
[IPV6] ADDRLABEL: Fix double free on label deletion.
[PPP]: Sparse warning fixes.
[IPV4] fib_trie: remove unneeded NULL check
[IPV4] fib_trie: More whitespace cleanup.
[NET_SCHED]: Use nla_policy for attribute validation in ematches
[NET_SCHED]: Use nla_policy for attribute validation in actions
[NET_SCHED]: Use nla_policy for attribute validation in classifiers
[NET_SCHED]: Use nla_policy for attribute validation in packet schedulers
[NET_SCHED]: sch_api: introduce constant for rate table size
[NET_SCHED]: Use typeful attribute parsing helpers
[NET_SCHED]: Use typeful attribute construction helpers
[NET_SCHED]: Use NLA_PUT_STRING for string dumping
[NET_SCHED]: Use nla_nest_start/nla_nest_end
[NET_SCHED]: Propagate nla_parse return value
[NET_SCHED]: act_api: use PTR_ERR in tcf_action_init/tcf_action_get
[NET_SCHED]: act_api: use nlmsg_parse
[NET_SCHED]: act_api: fix netlink API conversion bug
[NET_SCHED]: sch_netem: use nla_parse_nested_compat
[NET_SCHED]: sch_atm: fix format string warning
[NETNS]: Add namespace for ICMP replying code.
...
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (68 commits)
[MIPS] remove Documentation/mips/GT64120.README
[MIPS] Malta: remaining bits of the board support code cleanup
[MIPS] Malta: make the helper function static
[MIPS] Malta: fix braces at single statement blocks
[MIPS] Malta, Atlas: move an extern function declaration to the header file
[MIPS] Malta: Use C89 style for comments
[MIPS] Malta: else should follow close brace in malta_int.c
[MIPS] Malta: remove a superfluous comment
[MIPS] Malta: include <linux/cpu.h> instead of <asm/cpu.h>
[MIPS] Malta, Atlas, Sead: remove an extern from .c files
[MIPS] Malta: fix oversized lines in malta_int.c
[MIPS] Malta: remove a dead function declaration
[MIPS] Malta: use tabs not spaces
[MIPS] Malta: set up the screen info in a separate function
[MIPS] Malta: check the PCI clock frequency in a separate function
[MIPS] Malta: use the KERN_ facility level in printk()
[MIPS] Malta: use Linux kernel style for structure initialization
[MIPS]: constify function pointer tables
[MIPS] compat: handle argument endianess of sys32_(f)truncate64 with merge_64
[MIPS] Cobalt 64-bits kernels can be safely unmarked experimental
...
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (79 commits)
Remove references to "make dep"
kconfig: document use of HAVE_*
Introduce new section reference annotations tags: __ref, __refdata, __refconst
kbuild: warn about ld added unique sections
kbuild: add verbose option to Section mismatch reporting in modpost
kconfig: tristate choices with mixed tristate and boolean values
asm-generic/vmlix.lds.h: simplify __mem{init,exit}* dependencies
remove __attribute_used__
kbuild: support ARCH=x86 in buildtar
kconfig: remove "enable"
kbuild: simplified warning report in modpost
kbuild: introduce a few helpers in modpost
kbuild: use simpler section mismatch warnings in modpost
kbuild: link vmlinux.o before kallsyms passes
kbuild: introduce new option to enhance section mismatch analysis
Use separate sections for __dev/__cpu/__mem code/data
compiler.h: introduce __section()
all archs: consolidate init and exit sections in vmlinux.lds.h
kbuild: check section names consistently in modpost
kbuild: introduce blacklisting in modpost
...
Based upon the 2.4 kernel, the information presented in the
Documentation/mips/GT64120.README file is outdated. Worse,
the document contents are plain misleading nowadays because
the text mentions files and directories, which have been
deleted, moved or restructured for 2.6.
This patch removes the documentation, which is no more valid.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The journal checksum feature adds two new flags i.e
JBD2_FEATURE_INCOMPAT_ASYNC_COMMIT and JBD2_FEATURE_COMPAT_CHECKSUM.
JBD2_FEATURE_CHECKSUM flag indicates that the commit block contains the
checksum for the blocks described by the descriptor blocks.
Due to checksums, writing of the commit record no longer needs to be
synchronous. Now commit record can be sent to disk without waiting for
descriptor blocks to be written to disk. This behavior is controlled
using JBD2_FEATURE_ASYNC_COMMIT flag. Older kernels/e2fsck should not be
able to recover the journal with _ASYNC_COMMIT hence it is made
incompat.
The commit header has been extended to hold the checksum along with the
type of the checksum.
For recovery in pass scan checksums are verified to ensure the sanity
and completeness(in case of _ASYNC_COMMIT) of every transaction.
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Girish Shilamkar <girish@clusterfs.com>
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
This patch adds support for new firmware.
Old firmware is still supported until July 2008.
To get new firmware, go to
ftp://ftp.linksys.com/opensourcecode/wrt150nv11/1.51.3/
and download the tarball. We don't have a smaller tarball, yet.
That will be fixed later.
You can extract firmware out of the "wl_ap.o" file contained
in this tarball using latest fwcutter. You must pass the option
--unsupported to fwcutter.
Fwcutter-010 with official support for a new firmware image will
be released soon.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the bonding documentation: more discussion on
initialization and configuration, changes to discussion of packet
reordering in balance-rr, update some out of date information.
Based in part on input from Rick Jones <rick.jones2@hp.com>
and Andy Gospodarek <andy@greyhouse.net>.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
With all the newly introduced features, there is a lot to remove
later on after a compatibility grace period of 2 years.
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains the scheduled removal of the shaper driver.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the new PID TX rate control algorithm the default instead of the
rc80211_simple rate control algorithm. The simple algorithm was flawed in
several ways: it wasn't responsive at all and didn't age the information it was
relying on properly. The PID algorithm allows us to tune characteristics such
as responsiveness by adjusting parameters and was found to generally behave
better.
The default algorithm can be overridden to select simple instead. Which
ever algorithm is the default is included as part of the mac80211
module automatically. The other algorithm (simple vs. pid) can
be selected for inclusion as well. If EMBEDDED is selected then
the choice is available to have no default specified and neither
algorithm included in mac80211. The default algorithm can be set
through a modparam.
While at it, mark rc80211-simple as deprecated, and schedule it
for removal.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This statistics is shown factor dropped by transformation
at /proc/net/xfrm_stat for developer.
It is a counter designed from current transformation source code
and defined as linux private MIB.
See Documentation/networking/xfrm_proc.txt for the detail.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a socket option and signalling support for the case where the server
holds timewait state on closing the connection, as described in RFC 4340, 8.3.
Since holding timewait state at the server is the non-usual case, it is enabled
via a socket option. Documentation for this socket option has been added.
The setsockopt statement has been made resilient against different possible cases
of expressing boolean `true' values using a suggestion by Ian McDonald.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the ipt_SAME target as scheduled in feature-removal-schedule.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks dave, herbert, gerrit, andi and other people for your
discussion about this problem.
UdpInDatagrams can be confusing because it counts packets that
might be dropped later.
Move UdpInDatagrams into recvmsg() as allowed by the RFC.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Schedule softmac for for removal in the 2.6.26 development window.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Schedule bcm43xx for for removal in the 2.6.26 development window.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses the following problems:
1. DCCP relies for its proper functioning on having at least one CCID module
enabled (as in TCP plugable congestion control). Currently it is possible to
disable both CCIDs and thus leave the DCCP module in a compiled, but entirely
non-functional state: no sockets can be created when no CCID is available.
Furthermore, the protocol is (again like TCP) not intended to be used without
CCIDs. Last, a non-empty CCID list is needed for doing CCID feature negotiation.
2. Internally the default CCID that is advertised by the Linux host is set to CCID2
(DCCPF_INITIAL_CCID in include/linux/dccp.h). Disabling CCID2 in the Kconfig
menu without changing the defaults leads to a failure `module not found' when
trying to load the dccp module (which internally tries to load the default CCID).
3. The specification (RFC 4340, sec. 10) treats CCID2 somewhat like a
`minimum common denominator'; the specification says that:
* "New connections start with CCID 2 for both endpoints"
* "A DCCP implementation intended for general use, such as an implementation in a
general-purpose operating system kernel, SHOULD implement at least CCID 2.
The intent is to make CCID 2 broadly available for interoperability [...]"
Providing CCID2 as minimum-required CCID (like Reno/Cubic in TCP) thus seems reasonable.
Hence this patch automatically selects CCID2 when DCCP is enabled. Documentation also added.
Discussions with Ian McDonald on this subject are gratefully acknowledged.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This updates the DCCP documentation, following input from Ian McDonald,
clarifiying the status of DCCP, and adding a note about the test tree.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This extends the DCCP socket API by honouring any shutdown(2) option set by the user.
The behaviour is, as much as possible, made consistent with the API for TCP's shutdown.
This patch exploits the information provided by the user via the socket API to reduce
processing costs:
* if the read end is closed (SHUT_RD), it is not necessary to deliver to input CCID;
* if the write end is closed (SHUT_WR), the same idea applies, but with a difference -
as long as the TX queue has not been drained, we need to receive feedback to keep
congestion-control rates up to date. Hence SHUT_WR is honoured only after the last
packet (under congestion control) has been sent;
* although SHUT_RDWR seems nonsensical, it is nevertheless supported in the same manner
as for TCP (and agrees with test for SHUTDOWN_MASK in dccp_poll() in net/dccp/proto.c).
Furthermore, most of the code already honours the sk_shutdown flags (dccp_recvmsg() for
instance sets the read length to 0 if SHUT_RD had been called); CCID handling is now added
to this by the present patch.
There will also no longer be any delivery when the socket is in the final stages, i.e. when
one of dccp_close(), dccp_fin(), or dccp_done() has been called - which is fine since at
that stage the connection is its final stages.
Motivation and background are on http://www.erg.abdn.ac.uk/users/gerrit/dccp/notes/shutdown
A FIXME has been added to notify the other end if SHUT_RD has been set (RFC 4340, 11.7).
Note: There is a comment in inet_shutdown() in net/ipv4/af_inet.c which asks to "make
sure the socket is a TCP socket". This should probably be extended to mean
`TCP or DCCP socket' (the code is also used by UDP and raw sockets).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds documentation for the PF_CAN protocol family.
Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: Urs Thuermann <urs.thuermann@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the possibility to import a value from the environment into kconfig
via the option syntax. Beside flexibility this has the advantage
providing proper dependencies.
Documented the options syntax.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Add a section on kconfig hints: how to do <something> in Kconfig files.
Fix a few typos/spellos.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Also:
- rename "fsl_spi" to "fsl,spi";
- add and use cell-index property, if found;
- split probing code out of fsl_spi_init, thus we can call
it for legacy device_type probing and new "compatible" probing.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now we're searching for "fsl,qe", "fsl,qe-muram", "fsl,qe-muram-data"
and "fsl,qe-ic".
Unfortunately it's still impossible to remove device_type = "qe"
from the existing device trees because older u-boots are looking for it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for another variant of the VT8237. I couldn't test
I2C block support but I assume it is present as well.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
I2C block read is supported since the ICH5. I couldn't get it to work
using the block buffer, so it's using the old-style byte-by-byte mode
for now.
Note: I'm also updating the driver author... The i2c-i801 driver was
really written by Mark Studebaker, even though he based his work on
the i2c-piix4 driver which was written by Philip Edelbrock.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
i2c_adapter.list is superfluous, this list duplicates the one
maintained by the driver core. Drop it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
The framebuffer drivers for these pieces of hardware include support
for the DDC/I2C buses, so there is no need for separate drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch contains the overdue removal of three I2C drivers.
[JD: In fact only i2c-ixp4xx can be removed at the moment, the other two
platforms don't implement the generic GPIO layer yet.]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch contains the scheduled removal of legacy I2C RTC drivers with
replacement drivers.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There's a new script named i2c-stub-from-dump that can be very helpful
when working with the i2c-stub driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (63 commits)
ide: remove REQ_TYPE_ATA_CMD
ide: switch ide_cmd_ioctl() to use REQ_TYPE_ATA_TASKFILE requests
ide: switch set_xfer_rate() to use REQ_TYPE_ATA_TASKFILE requests
ide: fix final status check in drive_cmd_intr()
ide: check BUSY and ERROR status bits before reading data in drive_cmd_intr()
ide: don't enable local IRQs for PIO-in in driver_cmd_intr() (take 2)
ide: convert "empty" REQ_TYPE_ATA_CMD requests to use REQ_TYPE_ATA_TASKFILE
ide: initialize rq->cmd_type in ide_init_drive_cmd() callers
ide: use wait_drive_not_busy() in drive_cmd_intr() (take 2)
ide: kill DATA_READY define
ide: task_end_request() fix
ide: use rq->nr_sectors in task_end_request()
ide: remove needless ->cursg clearing from task_end_request()
ide: set IDE_TFLAG_IN_* flags before queuing/executing command
ide-tape: fix handling of non-special requests in ->end_request method
ide: fix final status check in task_in_intr()
ide: clear HOB bit for REQ_TYPE_ATA_CMD requests in ide_end_drive_cmd()
ide: fix ->io_32bit race in ide_taskfile_ioctl()
cmd64x: remove /proc/ide/cmd64x
ide: remove broken disk byte-swapping support
...
Remove broken disk byte-swapping support:
- it can cause a data corruption on SMP (or if using PREEMPT on UP)
- all data coming from disk are byte-swapped by taskfile_*_data() which
results in incorrect identify data being reported by /proc/ide/ and IOCTLs
- "hdx=bswap/byteswap" kernel parameter has been broken on m68k host drivers
(including Atari/Q40 ones) since 2.5.x days (because of 'hwif' zero-ing)
- byte-swapping is limited to PIO transfers (for working with TiVo disks on
x86 machines using user-space solutions or dm-byteswap should result in
much better performance because DMA can be used)
For previous discussions please see:
http://www.ussg.iu.edu/hypermail/linux/kernel/0201.0/0768.htmlhttp://lkml.org/lkml/2004/2/28/111
[ I have dm-byteswap device mapper target if somebody is interested
(patch is for 2.6.4 though but I'll dust it off if needed). ]
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make remaining built-in only IDE host drivers modular, add ide-scan-pci.c
file for probing PCI host drivers registered with IDE core (special case
for built-in IDE and CONFIG_IDEPCI_PCIBUS_ORDER=y) and then take care of
the ordering in which all IDE host drivers are probed when IDE is built-in
during link time.
* Move probing of gayle, falconide, macide, q40ide and buddha (m68k arch
specific) host drivers, before PCI ones (no PCI on m68k), ide-cris (cris
arch specific), cmd640 (x86 arch specific) and pmac (ppc arch specific).
* Move probing of ide-cris (cris arch specific) host driver before cmd640
(x86 arch specific).
* Move probing of mpc8xx (ppc specific) host driver before ide-pnp (depends
on ISA and none of ppc platform that use mpc8xx supports ISA) and ide-h8300
(h8300 arch specific).
* Add "probe_vlb" kernel parameter to cmd640 host driver and update
Documentation/ide.txt accordingly.
* Make IDE_ARM config option visible so it can also be disabled if needed.
* Remove bogus comment from ide.c while at it.
v2:
* Fix two issues spotted by Sergei:
- replace ENOMEM error value by ENOENT in ide-h8300 host driver
- fix MODULE_PARM_DESC() in cmd640 host driver
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There have been patches hanging around for ages to add support for
cpufreq to PXA255 processors. It's about time we applied one.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It caused only a lot of confusion. From now on cpu hotplug of up to
NR_CPUS will work by default. If somebody wants to limit that then
the possible_cpus parameter can be used.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
From: Cornelia Huck <cornelia.huck@de.ibm.com>
Change the adapter interrupt interface in order to allow multiple
adapter interrupt handlers to be registered. Indicators are now
allocated by cio instead of the device driver.
The qdio parts have been
Acked-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Information about a ccw device will be dumped in
case of a ccw timeout. This can be enabled with
the kernel parameter ccw_timeout_log.
Signed-off-by: Sebastian Ott <sebott@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
Hook up ocfs2_flock(), using the new flock lock type in dlmglue.c. A new
mount option, "localflocks" is added so that users can revert to old
functionality as need be.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Local alloc is a performance optimization in ocfs2 in which a node
takes a window of bits from the global bitmap and then uses that for
all small local allocations. This window size is fixed to 8MB currently.
This patch allows users to specify the window size in MB including
disabling it by passing in 0. If the number specified is too large,
the fs will use the default value of 8MB.
mount -o localalloc=X /dev/sdX /mntpoint
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Mostly taken from ext3. This allows the user to set the jbd commit interval,
in seconds. The default of 5 seconds stays the same, but now users can
easily increase the commit interval. Typically, this would be increased in
order to benefit performance at the expense of data-safety.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
We need to reserve at least two ioctls for online-resize. Reserve a small
range of ioctls for Ocfs2 use in Documentation/ioctl-number.txt. This should
give us enough room for future growth.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Remove 'readpages' from the list in ocfs2.txt. Instead of having two
identical lists, I just removed the list in the OCFS2 section of fs/Kconfig
and added a pointer to Documentation/filesystems/ocfs2.txt.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (81 commits)
RDMA/cxgb3: Fix the T3A workaround checks
IB/ipath: Remove unnecessary cast
IPoIB: Constify seq_operations function pointer tables
RDMA/cxgb3: Mark QP as privileged based on user capabilities
RDMA/cxgb3: Fix page shift calculation in build_phys_page_list()
RDMA/cxgb3: Flush the receive queue when closing
IB/ipath: Trivial simplification of ipath_make_ud_req()
IB/mthca: Update latest "native Arbel" firmware revision
IPoIB: Remove redundant check of netif_queue_stopped() in xmit handler
IB/ipath: Add mappings from HW register to PortInfo port physical state
IB/ipath: Changes to support PIO bandwidth check on IBA7220
IB/ipath: Minor cleanup of unused fields and chip-specific errors
IB/ipath: New sysfs entries to control 7220 features
IB/ipath: Add new chip-specific functions to older chips, consistent init
IB/ipath: Remove unused MDIO interface code
IB/ehca: Prevent RDMA-related connection failures on some eHCA2 hardware
IB/ehca: Add "port connection autodetect mode"
IB/ehca: Define array to store SMI/GSI QPs
IB/ehca: Remove CQ-QP-link before destroying QP in error path of create_qp()
IB/iser: Add change_queue_depth method
...
Remove MSI support from the mthca driver, as scheduled. There is no
reason to use MSI instead of MSI-X, since MSI-X performs better. No
one has spoken up since MSI support was deprecated in commit f6be6fbe
("IB/mthca: Schedule MSI support for removal"), so apparently the MSI
support is unused.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (509 commits)
V4L/DVB (7078): radio: fix sf16fmi section mismatch
V4L/DVB (7077): bt878: remove handcrafted PCI subsystem ID check
V4L/DVB (7075): Make a local function static
V4L/DVB (7074): DiB7000P: correct tuning problem for 7MHz channel
V4L/DVB (7073): DiB7070: Reception quality improved
V4L/DVB (7072): sets the MT2060 IF1 frequency according to EEPROM
V4L/DVB (7071): DiB0700: Start streaming the right way
V4L/DVB (7070): Fix some tuning problems
V4L/DVB (7069): Support for myTV.t
V4L/DVB (7068): Add support for WinTV Nova-T-CE driver
V4L/DVB (7067): fix autoserach in the Hauppauge NOVA-T 500
V4L/DVB (7066): ASUS My Cinema U3000 Mini DVBT Tuner
V4L/DVB (7065): Artec T14BR patches
V4L/DVB (7063): xc5000: Fix OOPS caused by missing firmware
V4L/DVB (7062): radio-si570x: Some fixes and new USB ID addition
V4L/DVB (7061): radio-si470x: Some cleanups
V4L/DVB (7060): em28xx: remove has_tuner
V4L/DVB (7059): cx88: Ensure the tuner is reset correctly
V4L/DVB (7058): IR corrections for the Pinnacle 800i
V4L/DVB (7056): tuner: suppress obsolete tuner i2c address warning for XC5000 tuners
...
This patch moves the subsystem ID and subsystem vendor ID check from probing
function to the PCI generic function by describing subsystem IDs in
pci_device_id table. This enables to add new PCI IDs to a device driver pci_ids
table at runtime by new_id file in sysfs pci driver tree.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
From Zhang: This patch continues the support for the Pinnacle HD 800i.
Patch committed as-is, cleanups to follow ... Steve
Signed-off-by: Chaogui Zhang <czhang1974@gmail.com>
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
From Zhang: This an updated patch that adds analog support for
the xc5000 tuner driver. it was tested on a Pinnacle PCTV HD 800i
card (patches to follow).
Patch commited as-is, cleanup to follow ... Steve.
Signed-off-by: Chaogui Zhang <czhang1974@gmail.com>
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks go to Mark Schultz for the initial contribution and to
Dean Hilkewich for testing it again.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add the "Pinnacle Studio PCTV USB (NTSC) FM" device.
This is the third occurrence of the same device designation...
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch updates cardlist for Beholder TV tuners:
old models (with GPIO ir) 401, 403, 405, 407, 409, 505, 507
and add support for 607, 609, M6 cards with new i2c-ir.
Signed-off-by: Igor Kuznetsov <igk72@yandex.ru>
Signed-off-by: Andrey J. Melnikov <temnota@kmv.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Kevin Lo