Move emulated format behind module parameter as those are not
supported. Format conversions will be on library eventually.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rework firmware selection logic a little bit.
Print notice asking user update firmware when old Si2168 B40
firmware is used.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Tested-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver uses that new firmware too, so advertise it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Tested-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add handling for different chip revisions and firmwares.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Command 0x14 returns 4 bytes as a reply. It is used for setting
key/value pairs to firmware and it returns 4 bytes back including
old value.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
No need to set explicitly value that are already defaulted same.
Setting new value returns old value. Firmware default values can
be found just looking returned value.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Same command was executed twice, but different value. Remove
redundant command.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use memcpy for set cmd buffer in order to keep style in line with
rest of file.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Detected symbol rate value was returned too small.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Inversion ON was reported as inversion OFF and vice versa.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
FEC AUTO is valid for PSK-8 modulation too. Add it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Only supported modulation for DVB-S is QPSK. Modulation parameter
contains invalid value for DVB-S on some cases, which leads driver
refusing tuning attempt. Due to that, hard code modulation to QPSK
in case of DVB-S.
Cc: stable@vger.kernel.org
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The message is currently highly encoded:
[70299.863521] DiB8000: Mpeg locks [ L0 : 0 | L1 : 1 | L2 : 0 ]
And doesn't properly reflect that some problems might have happened.
Instead, display it as:
[75160.822321] DiB8000: Not all ISDB-T layers locked in 32 ms: Layer A NOT LOCKED, Layer B locked, Layer C not enabled
In order to better reflect what's happening with layer locking.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When debug is enabled:
- Report when frontend gets restarted;
- Be coherent on the displayed lines;
- Show the transmission mode;
- Hide unused layers.
No functional changes (except at the printk's).
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This table doesn't match the new one.
Update it.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of doing the tuning delays and timeouts using
current_kernel_time(), use jiffies. That consumes less
CPU cycles, and it is monotonic.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
msleep() is not too precise: its precision depends on the
HZ config. As the driver selects precise timings for the
state machine, change it to usleep_range().
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
msleep() is not too precise: its precision depends on the
HZ config. As the driver selects precise timings for the
state machine, change it to usleep_range().
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Just like the Windows driver, restart SAD during reset
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
TV broadcasters generally use partial reception. So, enable it by
default in auto-search mode. The driver will latter detect if the
transmission is on some other mode.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The symbol duration was already obtained at CT_DEMOD_START.
No need to do it again at CT_DEMOD_STEP_3.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Without that, tuning may fail on 4K FFT mode, as the transmission
parameter cache will be initialized with a wrong value.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are two tabs instead of one aligning this struct.
Worse than that, on some places, the alignment is wrong.
Fix it.
No functional changes.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The ADC OFF values are wrong. This causes troubles on detecting
weak signals.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If interleave is bigger than 2, the code will set it to 0, as
dib8000 registers use a log2(). So, change the code to handle
it accordingly.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add static to tda m_* variables in the header. They don't need to be global.
With some cleanup they could probably even be marked const.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=68191
Reported-by: Christian Schneider <christian@ch-sc.de>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are several issues on the current code:
1) msleep(1) is actually equivalent to msleep(10);
2) au8522_video_set() will set reg 0xa4 to the
proper value for SIF, CVBS or S-Video. No need
to force it to CVBS;
3) Let's not hardcode 0x9d for CBS on audio_set.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
setup_decoder_defaults() doesn't really care about the input
port. All it needs to know is if the input port is s-video or
not.
As the caller function already knows that, just pass a boolean
instead.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Let's set the the audio routing also at stream start. With this change,
we don't risk enabling the analog demux while not streaming, reducing
the risk of interfering with a DVB demux that might be happening.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The same demod is used on both analog and digital mode. We should
not let the commands for analog mode to happen while the device
is in digital mode. So, monitor it via streamon.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The input mode is used not only inside the setup_decoder_defaults()
but also at au8522_*_mode routines.
So, move it one level up. As an advantage, we can now group the
function that sets the input into just one.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
First 8 bytes belonging to firmware image were hard-coded and uploaded
by the driver mistakenly. Introduce new corrected firmware file and
remove those 8 bytes from the driver.
New firmware image could be extracted from the PCTV 292e driver CD
using following command:
$ dd if=/TVC 6.4.8/Driver/PCTV Empia/emOEM.sys ibs=1 skip=1089408 count=2728 of=dvb-demod-si2168-02.fw
$ md5sum dvb-demod-si2168-02.fw
d8da7ff67cd56cd8aa4e101aea45e052 dvb-demod-si2168-02.fw
$ sudo cp dvb-demod-si2168-02.fw /lib/firmware/
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix following warnings:
si2168_cmd_execute() warn: add some parenthesis here?
si2168_cmd_execute() warn: maybe use && instead of &
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Calibrate the signal strength to dB.
For this callibration, I used adapter 0 (antenna 1), connected
via a normal cable to a DTF-2111 generator.
The same cabling and RF generator connected to adapter 1
(antenna 2) has a difference of +3dBm (signal was stronger
there).
Yet, changing the RF for a difference of, let's say, 6dB
reflected on a 6dB difference at the measured signal, with
is good.
So, the signal strengh can indeed be used to measure the
antenna gain, if the antenna is repositioned. It is
not precise to measure the absolute dBm value, however.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adds DVBv5 stats support. For now, just mimic whatever dib8000
does, as they're very similar, with regards to statistics.
However, dib7000p_get_time_us() likely require some
adjustments, as I didn't actually reviewed the formula
for it to work with DVB-T. Still, better than nothing,
as latter patches can improve it.
This patch also doesn't show the signal strength in dB
yet. The code is already there, but it requires to be
callibrated.
A latter patch will do the calibration.
It seems that this patch is also a bug fix: Before this
patch, the frontend were not tuning with some userspace
tools. I suspect that dib7000p firmware or hardware
internally expects that the statistics to be collected,
in order for it to work. With this patch, the DVB core
will always retrive statistics, even if userspace doesn't
request. So, it makes the device work on all tested apps.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Exporting multiple symbols don't work as it causes compilation
breakages, due to the way dvb_attach() works.
The bug happens when:
CONFIG_DVB_DIB8000=m
CONFIG_DVB_USB_DIB0700=y
As a bonus, dib8000 won't be loaded anymore if the device uses
a different frontend, reducing the memory footprint.
Tested with both Pixelview PV-D231 and MyGica S870.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Well, what we call as "foo_attach" is the method that should
be called by the dvb_attach() macro.
It should be noticed that the name "dvb_attach" is really a
bad name and don't express what it does.
dvb_attach() basically does three things, if the frontend is
compiled as a module:
- It lookups for the module that it is known to have the
given symbol name and requests such module;
- It increments the module usage (anonymously - so lsmod
doesn't print who loaded the module);
- after loading the module, it runs the function associated
with the dynamic symbol.
When compiled as builtin, it just calls the function given to it.
As dvb_attach() increments refcount, it can't be (easily)
called more than once for the same module, or the kernel
will deny to remove the module, because refcount will never
be zeroed.
In other words, the function name given to dvb_attach()
should be one single symbol that will always be called
before any other function on that module to be used.
For almost all DVB frontends, there's just one function,
but, on dib8000, there are several exported symbols.
We need to get rid of all those direct calls, because they
cause compilation breakages when bridge is builtin and
frontend is module, we'll need to add a new function that
will be the first one to be called, whatever initialization
is needed.
So, let's rename this function, in order to prepare for
a next patch that will add a new attach() function that
will be the only one exported by this module.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Exporting multiple symbols don't work as it causes compilation
breakages, due to the way dvb_attach() works.
This were reported several times, like:
drivers/built-in.o: In function `cxusb_dualdig4_rev2_tuner_attach':
>> cxusb.c:(.text+0x27d4b5): undefined reference to `dib7000p_get_i2c_master'
drivers/built-in.o: In function `dib7070_set_param_override':
cxusb.c:(.text+0x27d5a5): undefined reference to `dib0070_wbd_offset'
>> cxusb.c:(.text+0x27d5be): undefined reference to `dib7000p_set_wbd_ref'
drivers/built-in.o: In function `dib7070_tuner_reset':
>> cxusb.c:(.text+0x27d5f9): undefined reference to `dib7000p_set_gpio'
drivers/built-in.o: In function `cxusb_dualdig4_rev2_frontend_attach':
>> cxusb.c:(.text+0x27df5c): undefined reference to `dib7000p_i2c_enumeration'
In this specific report:
CONFIG_DVB_USB_CXUSB=y
CONFIG_DVB_DIB7000P=m
But the same type of bug can happen if:
CONFIG_DVB_DIB7000P=m
and one of the bridge drivers is compiled builtin (cxusb, cx23885-dvb
and/or dib0700).
As a bonus, dib7000p won't be loaded anymore if the device uses
a different frontend, reducing the memory footprint.
Tested with Hauppauge Nova-TD (2 frontends).
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Well, what we call as "foo_attach" is the method that should
be called by the dvb_attach() macro.
It should be noticed that the name "dvb_attach" is really a
bad name and don't express what it does.
dvb_attach() basically does three things, if the frontend is
compiled as a module:
- It lookups for the module that it is known to have the
given symbol name and requests such module;
- It increments the module usage (anonymously - so lsmod
doesn't print who loaded the module);
- after loading the module, it runs the function associated
with the dynamic symbol.
When compiled as builtin, it just calls the function given to it.
As dvb_attach() increments refcount, it can't be (easily)
called more than once for the same module, or the kernel
will deny to remove the module, because refcount will never
be zeroed.
In other words, the function name given to dvb_attach()
should be one single symbol that will always be called
before any other function on that module to be used.
For almost all DVB frontends, there's just one function.
However, the dib7000p initialization can require up to 3
functions to be called:
- dib7000p_get_i2c_master;
- dib7000p_i2c_enumeration;
- dib7000p_init (before this patch dib7000_attach).
(plus a bunch of other functions that the bridge driver will
need to call).
As we need to get rid of all those direct calls, because they
cause compilation breakages when bridge is builtin and
frontend is module, we'll need to add a new function that
will be the first one to be called, whatever initialization
is needed.
So, let's rename the function that probes and init the hardware
to dib7000p_init.
A latter patch will add a new dib7000p_attach that will be
used as originally conceived by dvb_attach() way.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
bit3 was not cleared always leaving driver reporting demod is not
fully locked. Do not check bit0 as it seems to be always 0.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add sleep ops to lgdt3304_ops to invoke lgdt3305_sleep() to be called
from dvb_frontend_suspend(). lgdt3305_soft_reset() is called for both
3304 and 3305 devices. soft_reset and sleep touch LGDT3305_GEN_CTRL_3
on 3304 and 3305 devices. Hence, adding sleep to lgdt3304_ops will help
suspend 3304 properly from dvb_frontend_suspend().
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The Kconfig entry for "Micronas DRX-J demodulator" defaults to modular
if DVB_FE_CUSTOMISE is set. But that Kconfig symbol was replaced with
MEDIA_SUBDRV_AUTOSELECT as of v3.7. So use the new symbol. And negate
the logic, because MEDIA_SUBDRV_AUTOSELECT's logic is the opposite of
the former logic.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
fix the following warnings:
m88rs2000.c:300:16: warning: symbol 'm88rs2000_setup' was not declared. Should it be static?
m88rs2000.c:318:16: warning: symbol 'm88rs2000_shutdown' was not declared. Should it be static?
m88rs2000.c:328:16: warning: symbol 'fe_reset' was not declared. Should it be static?
m88rs2000.c:366:16: warning: symbol 'fe_trigger' was not declared. Should it be static?
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Band switching didn't worked always reliably as there was one
register bit set wrong.
Thanks to Robert Schlabbach for pointing this bug and solution.
Reported-by: Robert Schlabbach <Robert.Schlabbach@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Exporting functions for hardware filter is a bad idea, as it
breaks compilation if:
CONFIG_DVB_USB_AF9035=y
CONFIG_DVB_AF9033=m
Because the PID filter function calls would be hardcoded at
af9035.
The same doesn't happen with af9033_attach() because the
dvb_attach() doesn't hardcode it. Instead, it dynamically
links it at runtime.
However, calling dvb_attach() multiple times is problematic,
as it increments module kref.
So, the better is to pass one parameter for the af9033 module
to fill the hardware filters, and then use it inside af9035.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement PID filter and export it via symbol.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It was possible that tuner_frequency variable, used for carrier offset
compensation, was uninitialized. That happens when tuner
.get_frequency() callback is not defined.
Currently that case is not possible as only used tuner has this callback.
Coverity CID 1166057: Uninitialized scalar variable (UNINIT)
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Coverity CID 1166051: Logically dead code (DEADCODE)
TS clock calculation could be more accurate, but as it is not,
remove those unused clock speeds.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are two troubles there:
1) the bit error measure were not accumulating;
2) it was missing the bit count.
Fix them.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function 'ctrl_get_qam_sig_quality':
drivers/media/dvb-frontends/drx39xyj/drxj.c:9468:6: warning: variable 'ber_cnt' set but not used [-Wunused-but-set-variable]
u32 ber_cnt = 0; /* BER count */
^
By reading the comment, it is said that BER should be calculated as:
qam_pre_rs_ber = frac_times1e6( ber_cnt, rs_bit_cnt );
Also, it makes sense to take the mantissa into account, so fix the
code to do what's commented.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that everything is set, let's enable DVBv5 stats, for
applications that support it.
DVBv3 apps will still work.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of just assuming that the min resolution is 1E-6,
pass both bit error and bit counts for userspace to calculate
BER. The same applies for PER, for 8VSB. It is not clear how
to get the packet count for QAM. So, for now, don't expose PER
for QAM.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Convert the stats internally to use DVBv5. For now, it will keep
showing everything via DVBv3 API only, as the .len value were
not initialized.
That allows testing if the new stats code didn't break anything.
A latter patch will add the final bits for the DVBv5 stats to
fully work.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We'll need to use this function. Restore it from the
git history.
This function will be used on the next patch.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
State is already used on other places for the state struct.
Don't use it here, to avoid troubles with latter patches.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported when compiled with W=1:
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function ‘ctrl_set_channel’:
drivers/media/dvb-frontends/drx39xyj/drxj.c:10340:26: warning: variable ‘common_attr’ set but not used [-Wunused-but-set-variable]
struct drx_common_attr *common_attr = NULL;
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:10336:6: warning: variable ‘intermediate_freq’ set but not used [-Wunused-but-set-variable]
s32 intermediate_freq = 0;
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This function is currently not used. However, it was meant to
be called at device release. So, add it there.
While here, remove the bad check, as reported by Dan, as
smatch warning:
drivers/media/dvb-frontends/drx39xyj/drxj.c:20041 drxj_close() warn: variable dereferenced before check 'demod' (see line 20036)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are large chunks of code at drx-j that aren't used. Most
of them are due to analog TV support. Well, just enabling them
won't make analog support work, as devices with DRX and analog
support requires an extra chip (avf4910).
We don't have drivers for it, nor the current device that uses
this frontend has support for analog TV.
So, let's just get rid of this code. If latter needed, this
patch can easily be reverted from git history.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by the kbuild test robot <fengguang.wu@intel.com>:
drivers/built-in.o: In function `em28xx_dvb_init':
em28xx-dvb.c:(.text+0x876f2c): undefined reference to `drx39xxj_attach'
That happens when CONFIG_VIDEO_EM28XX_DVB is selected, and neither
CONFIG_MEDIA_SUBDRV_AUTOSELECT or DVB_DRX39XYJ is selected.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fixes the following warnings:
drivers/media/dvb-frontends/drx39xyj/drxj.c:1679:65: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drx39xyj/drxj.c:1679:71: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drx39xyj/drxj.c:1681:52: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drx39xyj/drxj.c:1681:58: warning: Using plain integer as NULL pointer
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
No functional changes, but removes a duplicate check, if
!state->type_A.
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix sparse warning:
drivers/media/dvb-frontends/drx39xyj/drxj.c:1039:16: sparse: symbol 'drxj_default_aud_data_g' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Delay possible I2C gate close a little bit in order to see if there
is next message coming to tuner in a sequence.
Also, export private muxed I2C adapter. That is aimed only for SDR
extension module as SDR belongs to same RTL2832 physical I2C bus (it
is physically property of RTL2832, whilst it is own kernel module).
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There was a deadlock between master I2C adapter and muxed I2C
adapter. Implement two I2C muxed I2C adapters and leave master
alone, just only for offering I2C adapter for these mux adapters.
Reported-by: Luis Alves <ljalvs@gmail.com>
Reported-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
RTL2832 provides gated / repeater I2C adapter for tuner.
Implement it as a muxed I2C adapter.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Most of those were reported by checkpatch.pl...
debug module parameter is not used anywhere so remove it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
All used tuners has get_if_frequency() callback and that parameter
is not needed and will not needed as all upcoming tuner drivers
should implement get_if_frequency().
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently, there's just one device using this frontend: PCTV 80e,
and it works on serial mode.
Change the default here to serial mode. If we add more devices,
then this option should be set via config structure.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The cfg_mpeg_output has more fields than what it is initialized
when the code is called. Be sure to initialize everything before
use, in order to avoid random behaviors.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Just like the windows driver, disable OOB after setting the driver
version.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
DJH_DEBUG only code path in drxbsp_i2c_write_read() dereferences
w_dev_addr and subsequently w_dev_addr->user_data->i2c which results
in failure during boot. This patch fixes the null pointer derefence
bug as well as the following compile errors:
LD arch/x86/built-in.o
CC drivers/media/dvb-frontends/drx39xyj/drxj.o
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function ‘drxbsp_i2c_write_read’:
drivers/media/dvb-frontends/drx39xyj/drxj.c:1558:25: error: redeclaration of ‘state’ with no linkage
struct drx39xxj_state *state = w_dev_addr->user_data;
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1512:25: note: previous declaration of ‘state’ was here
struct drx39xxj_state *state;
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1558:2: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement]
struct drx39xxj_state *state = w_dev_addr->user_data;
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1560:17: error: redeclaration of ‘msg’ with no linkage
struct i2c_msg msg[2] = {
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:1513:17: note: previous declaration of ‘msg’ was here
struct i2c_msg msg[2];
^
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mimic what windows driver does here: it writes 0x07 to
SIO_CC_SOFT_RST__A, instead of just 0x03.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As drxj_close puts the device in powerdown, we need to power it up
properly at drxj_open.
This is the behavior noticed at the Windows driver.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are no other I2C masters here. Also, the Windows driver uses
this mode (and both drxd and drxk Kernel drivers). So, switch
to it.
That helps to compare the logs between the Linux driver and the
Windows one.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of just disabling the LNA every time, allow to control it from
userspace.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On several places, the I2C functions are just wrappers to others.
Get rid of it.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This struct contains the first abstraction layer for the I2C
access routines. Get rid of it.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This file contains an abstract layer for the I2C transfer
functions. Get rid of it, merging it at drxj. This will allow
to remove another abstraction layer there, making the code
easier to read, and removing the functions that just return
-EIO.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reorder functions and data at drx_dap_fasi.c, in order to avoid
having function prototypes.
This is in preparation to merge this code inside drxj, removing
some duplicated bits there, and getting rid of yet another
abstraction layer.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is not used anywere. Get rid of it.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
QAM/256 currently doesn't work, as the code is only called if
channel->mirror is DRX_MIRROR_AUTO, but a prevous if prevents
this condition to happen.
While here, returns -EINVAL to not supported QAM modes and
simplify the code, reducing the number of indents.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Those struct data aren't used anymore. Get rid of them.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Checking if a time is after another one can have issues, as
times are generally u32 wide.
Use the proper macros for that at scu_command().
It should be noticed that other places also use jiffies
calculus on an improper way. This should be fixed too,
but the logic there is more complex. So, let's do it in
separate patches.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Modulation and other parameters might have changed. So, better
to call ctrl_set_standard() even if the device is already
powered.
That helps to put the device into a sane state, if something
got wrong on a previous set_frontend call.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When switching from one video standard to another one,
power_down_vsb is called twice. Well, as the device is already
in power_down mode, the second call always fail. This causes that
any subsequent frontend set to fail as well:
[145074.501243] drx39xyj:power_down_vsb: called
[145089.195396] drx39xyj:power_down_vsb: error -5
[145089.195404] drx39xyj:ctrl_set_standard: error -5
[145089.195417] drx39xyj:drx39xxj_set_frontend: Failed to set standard! result=fffffffb
[145089.195470] drx39xyj:ctrl_sig_quality: error -5
[145089.195473] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145089.195475] drx39xyj:ctrl_sig_quality: error -5
[145089.195477] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145089.195479] drx39xyj:ctrl_sig_quality: error -5
[145089.195480] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145089.195482] drx39xyj:ctrl_sig_quality: error -5
[145089.195484] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
[145089.195498] drx39xyj:ctrl_sig_quality: error -5
[145089.195500] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145089.195502] drx39xyj:ctrl_sig_quality: error -5
[145089.195503] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145089.195505] drx39xyj:ctrl_sig_quality: error -5
[145089.195506] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145089.195508] drx39xyj:ctrl_sig_quality: error -5
[145089.195510] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
[145090.196291] drx39xyj:drx39xxj_read_status: drx39xxj: could not get lock status!
[145090.196508] drx39xyj:ctrl_sig_quality: error -5
[145090.196511] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145090.196514] drx39xyj:ctrl_sig_quality: error -5
[145090.196515] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145090.196518] drx39xyj:ctrl_sig_quality: error -5
[145090.196519] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145090.196522] drx39xyj:ctrl_sig_quality: error -5
[145090.196523] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
[145090.196553] drx39xyj:ctrl_sig_quality: error -5
[145090.196554] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145090.196557] drx39xyj:ctrl_sig_quality: error -5
[145090.196558] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145090.196560] drx39xyj:ctrl_sig_quality: error -5
[145090.196562] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145090.196564] drx39xyj:ctrl_sig_quality: error -5
[145090.196565] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
[145091.119265] drx39xyj:ctrl_sig_quality: error -5
[145091.119271] drx39xyj:drx39xxj_read_ber: drx39xxj: could not get ber!
[145091.119274] drx39xyj:ctrl_sig_quality: error -5
[145091.119276] drx39xyj:drx39xxj_read_signal_strength: drx39xxj: could not get signal strength!
[145091.119278] drx39xyj:ctrl_sig_quality: error -5
[145091.119280] drx39xyj:drx39xxj_read_snr: drx39xxj: could not read snr!
[145091.119282] drx39xyj:ctrl_sig_quality: error -5
[145091.119283] drx39xyj:drx39xxj_read_ucblocks: drx39xxj: could not get uc blocks!
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of just hardcoding an IF value of 5MHz, use the one
provided by the tuner, with can be different for QAM and
VSB.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Those functions will never be used with Linux DVB binding.
Get rid of them.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This file does an ugly binding between drxj and DVB frontend.
Remove most of the functions there. We still need to get rid of
get_frequency and set_frequency, but such patch is a little more
complex, as it should also remove some previous tuner bindings.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In order to avoid warnings and to remove dead code, remove
the functions that don't make sense to happen, while commenting
the others that might still be useful some day.
That reduced a lot the text size:
Before:
text data bss dec hex filename
58419 2916 4 61339 ef9b drivers/media/dvb-frontends/drx39xyj/drx39xyj.ko
After:
text data bss dec hex filename
78331 2916 4 81251 13d63 drivers/media/dvb-frontends/drx39xyj/drx39xyj.ko
Without any functional changes.
It could be make sense latter to remove those drivers or to
move them into an analog-specific part of the driver.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
With this change, we finally got rid of all abstraction
layers on this driver.
This patch also fixes the LNA GPIO settings, as the original
code were using a wrong control name for it.
This patch exposes the several functions that aren't used.
Some of them are related to analog demod that might be
used some day, but others will likely never be needed, as
they don't fit on Linux media APIs.
Latter patches will clean up this mess.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
While drxj is already too big, moving the code there will
make easier to get rid of the drxj_ctrl function.
It will also help to detect and remove the unused functions,
helping to remove lots of dead code there.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Get rid of drx_open and drx_close, as those are just wrapper
functions to drxj_open/drxj_close.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This function is used only as an abstraction layer to call the
two firmware functions. Remove it.
As a bonus, the drx_ctrl_function is now unused and can be
removed.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove the duplicated firmware upload code that was commented
inside drxj.c.
This code is not used, and will not work anyway, as it doesn't
download the firmware from userspace.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The version is initialized with zero at drx_driver.c. Keep it,
in order to avoid the risk of causing any regression.
While here, remove the drx_driver.h from drxj, as this is not
required there.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This file contains just the firmware load code, that it is also
somewhat duplicated at drxj.c.
Move the code into there. Latter patches will remove the
duplicated code.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In order to prepare to get rid of drx_driver.c, prepend all functions
there with drx_.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is mostly CodingStyle fixes and improvements.
No functional changes.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
ClearQAM is currently not working. Add support for it too.
Unlikely other ATSC tuners, though, this device will not
auto-detect between ATSC and ClearQAM. So, the delivery
system should be properly set.
Also, this frontend seems to also support DVB-C annex A/C. Add
experimental support for them.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Without this fixup, the DRX-J will not be properly initialized,
loosing several PIDs.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of handling endiannes with its own internal way, use the
already existing macros.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are several drx-j code there that are never used, as
they don't even fit into Linux DVB subystem model.
Remove them, in order to simplify the code.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The firmware upload routine is already complex enough. Split the
first loop that verifies the firmware size into a separate routine,
making the code more readable.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of hardcoding the firmware files together with the driver,
use request_firmware() way, loading it from userspace.
The firmware files are placed at:
http://linuxtv.org/downloads/firmware/#8
And they'll be latter submitted to linux-firmware git tree.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The state struct is allocated without cleaning the memory.
This causes random bugs.
Clean it, and move the memcpy functions just below each kalloc,
to be clearer that all those data are properly filled.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are memory leaks on both DVB release and
dvb attach error path. Fix them.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This var is not used. Remove it from the code, as we'll now be
converting the driver to load the firmware from an external
file.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This file is empty (actually, all commented there). So, remove it.
We should latter remove those macros too, or convert them into
a struct to allow dynamically enable the options during device
probing time.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Get rid of another typedef defined on this driver.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of using printk's, use the pr_foo() macros.
That fixes some checkpatch warnings and provide a better error,
warning and debug support.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of defining its own set of error codes, use the linux
native ones.
Please note that this patch made a "stupid" error code mapping, just
replacing the codes with the closest one. In special, -EIO is being
used on several places. I'm pretty sure this could be better assigned,
but a change like that would require lots o time and efforts, without
much benefit.
So lets do adjstments at the error codes latter, when we have more
time.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix almost all checkpatch.pl warnings/errors on drxj.c, except for:
- 80 cols whitespacing;
- too many leading tabs;
- a false positive at DRXJ_16TO8() macro.
- static char array declaration should probably be static const char
as adding "const" would cause warnings.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove three typedefs from drxj.c, using the following script:
use File::Find;
use strict;
my $dir = shift or die "need a dir";
my $type = shift or die "need type";
my $var = shift or die "need var";
sub handle_file {
my $file = shift;
my $out;
open IN, $file or die "can't open $file";
$out .= $_ while (<IN>);
close IN;
$out =~ s/\btypedef\s+($type)\s+\{([\d\D]+?)\s*\}\s+\b($var)[^\;]+\;/$type $var \{\2\};/;
# This replaces the typedef declaration for a simple struct declaration - style 1
# This replaces the typedef declaration for a simple struct declaration - style 2
# Replace struct occurrences
$out =~ s,\b($var)_t\s+,$type \1 ,g;
$out =~ s,\bp_*($var)_t\s+,$type \1 *,g;
$out =~ s,\b($var)_t\b,$type \1,g;
$out =~ s,\bp_*($var)_t\b,$type \1 *,g;
open OUT, ">$file" or die "can't open $file";
print OUT $out;
close OUT;
}
sub parse_dir {
my $file = $File::Find::name;
return if (!($file =~ /.[ch]$/));
handle_file $file;
}
find({wanted => \&parse_dir, no_chdir => 1}, $dir);
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Don't need to test boolean x == true or x == false.
That makes the code more compact.
patch generated with make coccicheck and manually reviewed.
While here, remove uneeded ';'.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
CodingStyle fix: don't use parenthesis on return, as it is not
a function.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function ‘drxj_dap_scu_atomic_read_reg16’:
drivers/media/dvb-frontends/drx39xyj/drxj.c:4170:9: warning: ‘*((void *)&buf+1)’ may be used uninitialized in this function [-Wmaybe-uninitialized]
word = (u16) (buf[0] + (buf[1] << 8));
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:4170:9: warning: ‘buf’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function ‘drxj_dap_atomic_read_reg32.isra.59’:
drivers/media/dvb-frontends/drx39xyj/drxj.c:2186:7: warning: ‘*((void *)&buf+3)’ may be used uninitialized in this function [-Wmaybe-uninitialized]
word = (u32) buf[3];
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:2188:10: warning: ‘*((void *)&buf+2)’ may be used uninitialized in this function [-Wmaybe-uninitialized]
word |= (u32) buf[2];
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:2190:10: warning: ‘*((void *)&buf+1)’ may be used uninitialized in this function [-Wmaybe-uninitialized]
word |= (u32) buf[1];
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:2192:10: warning: ‘buf’ may be used uninitialized in this function [-Wmaybe-uninitialized]
word |= (u32) buf[0];
^
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This were fixed with the help of this small perl script:
#!/usr/bin/perl
my $dir = shift or die "need a dir";
my $type = shift or die "need type";
my $var = shift or die "need var";
sub handle_file {
my $file = shift;
my $out;
open IN, $file or die "can't open $file";
$out .= $_ while (<IN>);
close IN;
$out =~ s/\btypedef\s+($type)\s+\{([\d\D]+?)\s*\}\s+\b($var)[^\;]+\;/$type $var \{\2\};/;
$out =~ s,\b($var)_t\s+,$type \1 ,g;
$out =~ s,\bp_*($var)_t\s+,$type \1 *,g;
$out =~ s,\b($var)_t\b,$type \1,g;
$out =~ s,\bp_*($var)_t\b,$type \1 *,g;
open OUT, ">$file" or die "can't open $file";
print OUT $out;
close OUT;
}
sub parse_dir {
my $file = $File::Find::name;
return if (!($file =~ /.[ch]$/));
handle_file $file;
}
find({wanted => \&parse_dir, no_chdir => 1}, $dir);
Some manual work were needed.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Most of the changes were done with scripts like:
for i in drivers/media/dvb-frontends/drx39xyj/*.[ch]; do perl -ne '$var = "drx_sig_quality"; s,\b($var)_t\s+,struct \1 ,g; s,\bp_*($var)_t\s+,struct \1 *,g; s,\b($var)_t\b,struct \1,g; s,\bp_*($var)_t\b,struct \1 *,g; print $_' <$i >a && mv a $i; done
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This file is not used anywhere. Drop it.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
None of those vars are used on those functions. Just remove them.
After this patch, there's just one of such warnings:
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function 'ctrl_get_qam_sig_quality':
drivers/media/dvb-frontends/drx39xyj/drxj.c:7872:6: warning: variable 'ber_cnt' set but not used [-Wunused-but-set-variable]
u32 ber_cnt = 0; /* BER count */
We'll keep it, as BER count will be useful when converting the
frontend to report statistics via DVBv5 API
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This function is not static. Also, it is not used anywhere.
So, drop it.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Antti Palosaari