The ETH_P_BATMAN ethertype is now defined kernel-wide. Use it instead
of the private BATADV_ETH_P_BATMAN define.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
All packet headers in front of an ethernet header have to be completely
divisible by 2 but not by 4 to make the payload after the ethernet header again
4 bytes boundary aligned.
A packing of 2 is necessary to avoid extra padding at the end of the struct
caused by a structure member which is larger than two bytes. Otherwise the
structure would not fulfill the previously mentioned rule to avoid the
misalignment of the payload after the ethernet header. It may also lead to
leakage of information when the padding it not initialized before sending.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
If the skb is fragmented, the checksum must be computed on the
individual fragments, just using skb->data may fail on fragmented
data. Instead of doing linearizing the packet, use the new
batadv_crc32 to do that more efficiently- it should not hurt
replacing the old crc16 by the new crc32.
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
By adding batadv_send_skb_to_orig() in send.c, we can remove duplicate
code that looks up the next hop and then calls batadv_send_skb_packet().
Furthermore, this prepares the upcoming new implementation of
fragmentation, which requires the next hop to route packets.
Please note that this doesn't entirely remove the next-hop lookup in
routing.c and unicast.c, since it is used by the current fragmentation
code.
Also note that the next-hop info is removed from debug messages in
translation-table.c, since it is looked up elsewhere.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
This patch adds support for an array of debugfs general (not soft_iface
specific) attributes. With this change it will be possible to add more general
attributes by simply appending them to the array without touching the rest of
the code.
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Acked-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
The address and the VLAN VID may not be packed in the respective
structs. Fix this by comparing the elements individually.
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The transtable_global debug file can show multiple entries for a single client
when multiple gateways exist. The chosen gateway isn't marked in the list and
therefore the user cannot easily debug the situation when there is a problem
with the currently used gateway.
The best gateway is now marked with "*" and secondary gateways are marked with
"+".
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The logic in the BLA mechanism may decide to drop broadcast packets
because the node may still be in the setup phase. For this reason,
further broadcast processing like the early client detection mechanism
must be done only after the BLA check.
This patches moves the invocation to BLA before any other broadcast
processing.
This was introduced 30cfd02b60
("batman-adv: detect not yet announced clients")
Reported-by: Glen Page <glen.page@thet.net>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
The "early client detection" mechanism must not add clients belonging
to other backbone nodes. Such clients must be reached by directly
using the LAN instead of the mesh.
This was introduced by 30cfd02b60
("batman-adv: detect not yet announced clients")
Reported-by: Glen Page <glen.page@thet.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
When a TT response with the full table is sent, the client flags
should be sent as well. This patch fix the flags assignment when
populating the tt_response to send back
This was introduced by 30cfd02b60
("batman-adv: detect not yet announced clients")
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Flags carried by a change_entry have to be always copied into the
client entry as they may contain important attributes (e.g.
TT_CLIENT_WIFI).
For instance, a client added by means of the "early detection
mechanism" has no flag set at the beginning, so they must be updated once the
proper ADD event is received.
This was introduced by 30cfd02b60
("batman-adv: detect not yet announced clients")
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
This patch allows clients to roam multiple times within the same
originator-interval.
To enable this new feature two key aspects that have been introduced:
1) packets are always directed to the node that was originally
serving the roamed client which will then re-route the data
to the correct destination at any point in time;
2) the client flags handling mechanism has been properly modified
in order to allow multiple roamings withinin the same orig-int.
Therefore flags are now set properly even in this scenario.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
batadv_tt_global_del_struct() function is not properly named.
Having a more meaningful name which reflects the current behavior helps other
developers to easily understand what it does.
A parameter has also been renamed in order to let the function header better fit
the 80-chars line-width
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
tt_poss_change is a node-wide flag which tells whether the node is in a roaming
state (a client recently moved to/away from it) in order to let it apply special
re-routing rules. However this flag does not give a clear idea of the current
state because it is not possible to understand *which client* is actually
involved in the roaming. For this reason a better approach has been chosen:
instead of using a node-wide variable, the roaming state is now given by a
per-tt_entry ROAM flag which, in case of packet coming through the node, tells
the node whether the real destination is in roaming state or not.
With this flag change, batadv_check_unicast_ttvn() has also been rearranged in
order to better fit the new re-routing logic and to be much more readable.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
For some reasons (bridge forward delay, network device setup order, etc)
the initial bridge loop avoidance announcement packets may be lost. This
may lead to problems in finding other backbone gws, and therfore create
loops in the startup time.
Fix this by extending the waiting periods to 3 (define can be changed)
before allowing broadcast traffic.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
When adding a backbone gateway for the first time, it might not yet
be known in the backbone, and therefore we should not forward
broadcasts yet. This behaviour is the same as when sending a request
to another backbone gw because of a CRC mismatch. The backbone gw
will operate normal after the next periodic bla work.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
To avoid loops in the startup phase until the first announcement is
sent, send an announcement immediately as soon as a backbone gw is
added.
This may happen due to various reasons, e.g. a packet passes the rx
or tx path.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Any virtual device created on top of a batman-adv mesh interface must be
prevented to be used to create a new mesh network (this would lead to an
unwanted batman-over-batman configuration)
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The hash functions in the bridge loop avoidance code expects the
VLAN vid to be right after the mac address, but this is not guaranteed.
Fix this by explicitly hashing over the right fields of the struct.
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The "early client detection mechanism" can be extended to find new clients by
means of unicast_4addr packets.
The unicast_4addr packet contains as well as the broadcast packet (which is
currently used in this mechanism) the address of the originating node and can
therefore be used to install new entries in the Global Translation Table
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
This patch adds a runtime switch that enables the user to turn the DAT feature
on or off at runtime
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
This patch makes it possible to decide whether to include DAT within the
batman-adv binary or not.
It is extremely useful when the user wants to reduce the size of the resulting
module by cutting off any not needed feature.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
In case of an ARP message going in or out the soft_iface, it is intercepted and
a special action is performed. In particular the DHT helper functions previously
implemented are used to store all the ARP entries belonging to the network in
order to provide a fast and unicast lookup instead of the classic broadcast
flooding mechanism.
Each node stores the entries it is responsible for (following the DHT rules) in
its soft_iface ARP table. This makes it possible to reuse the kernel data
structures and functions for ARP management.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
ARP messages are now parsed to make it possible to trigger special actions
depending on their types (snooping).
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Since batman-adv cannot inter-operate with the host ARP table, this patch
introduces a batman-adv private storage for ARP entries exchanged within DAT.
This storage will represent the node local cache in the DAT protocol.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Add all the relevant functions in order to manage a Distributed Hash Table over
the B.A.T.M.A.N.-adv network. It will later be used to store several ARP entries
and implement DAT (Distributed ARP Table)
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
A new log level has been added to concentrate messages regarding DAT: ARP
snooping, requests, response and DHT related messages.
The new log level is named BATADV_DBG_DAT
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The current unicast packet type does not contain the orig source address. This
patches add a new unicast packet (called UNICAST_4ADDR) which provides two new
fields: the originator source address and the subtype (the type of the data
contained in the packet payload). The former is useful to identify the node
which injected the packet into the network and the latter is useful to avoid
creating new unicast packet types in the future: a macro defining a new subtype
will be enough.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Headers which are already perfectly aligned and create a 4 byte boundary
non-ethernet header payload can have the __packed attribute removed. The
__packed attribute doesn't change the appeareance of the packet for these
headers because no extra padding is necessary to align the data members. The
compiler will also create slightly faster code for loads of multi-byte members.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The ethernet header is 14 bytes long. Therefore, the data after it is not 4
byte aligned and may cause problems on systems without unaligned data access.
Reserving NET_IP_ALIGN more byes can fix the misalignment of the ethernet
header.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
in case of client roaming a new global entry is added while a corresponding
local one is still present. In this case the node can safely pass the WIFI flag
from the local to the global entry.
This change is required to let the AP-isolation correctly working in case of
roaming: if a generic WIFI client C roams from node A to B, A adds a global
entry for C without adding any WIFI flag. The latter will be set only later,
once A has received C's advertisement from B. In this time period the
AP-Isolation (if enabled) would not correctly work since C is not marked as
WIFI, so allowing it to communicate with other WIFI clients.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
In order to properly convert a bitwise AND to a boolean value, the whole
expression must be prepended by "!!".
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
In batadv_check_unicast_ttvn() the code accesses both the unicast header and the
Ethernet header in the payload. For this reason pskb_may_pull() must be invoked
to check for the required space.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
To simplify TranslationTable debugging it is better to print the packet
rerouting message on the DBG_TT log level. In this way a developer interested in
packets rerouting doesn't need to filter it out of the whole ROUTES log.
Moreover, since this message will appear for each rerouted message, it is now
"ratelimited".
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
in case of a new global entry added because of roaming, the roam_at field must
be properly initiated with the current time. This value will be later use to
purge this entry out on time out (if nobody claims it). Instead roam_at field
is now set to zero in this situation leading to an immediate purging of the
related entry.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
We have seen this to break networks when used with bridge loop
avoidance. As we can't see any benefit from sending these ancient frames
via our mesh, we just drop them.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The test whether we can use a router for alternating bonding should only be
done once because it is already known that it is still usable and will not be
deleted from the list soon.
This patch addresses Coverity #712285: Unchecked return value
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
New operations should not be started when they need an increased module
reference counter and try_module_get failed.
This patch addresses Coverity #712284: Unchecked return value
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
batadv_bit_get_packet checks for all common situations before it decides that
the new received packet indicates that the host was restarted. This extra
condition check at the end of the function is not necessary because this
condition is always true.
This patch addresses Coverity #712296: Logically dead code
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Transmissions over batman-adv devices always start another nested transmission
over devices attached to the batman-adv interface. These devices usually use
the ethernet lockdep class for the tx_queue lock which is also set by default
for all batman-adv devices. Lockdep will detect a nested locking attempt of two
locks with the same class and warn about a possible deadlock.
This is the default and expected behavior and should not alarm the locking
correctness prove mechanism. Therefore, the locks for all netdevice specific tx
queues get a special batman-adv lock class to avoid a false positive for each
transmission.
Reported-by: Linus Luessing <linus.luessing@web.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
To avoid code duplication and to simplify further changes,
check_unicast_packet() is now used in recv_roam_adv() to check for not
well formed packets and so discard them.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Threads in the bottom half of batadv_bla_check_bcast_duplist() might
otherwise for instance overwrite variables which other threads might
be using/reading at the same time in the top half, potentially
leading to messing up the bcast_duplist, possibly resulting in false
bridge loop avoidance duplicate check decisions.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
So far the crc16 checksum for a batman-adv broadcast data packet, received
on a batman-adv hard interface, was calculated over zero bytes of its
content leading to many incoming broadcast data packets wrongly being
dropped (60-80% packet loss).
This patch fixes this issue by calculating the crc16 over the actual,
complete broadcast payload.
The issue is a regression introduced by
("batman-adv: add broadcast duplicate check").
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Conflicts:
drivers/net/team/team.c
drivers/net/usb/qmi_wwan.c
net/batman-adv/bat_iv_ogm.c
net/ipv4/fib_frontend.c
net/ipv4/route.c
net/l2tp/l2tp_netlink.c
The team, fib_frontend, route, and l2tp_netlink conflicts were simply
overlapping changes.
qmi_wwan and bat_iv_ogm were of the "use HEAD" variety.
With help from Antonio Quartulli.
Signed-off-by: David S. Miller <davem@davemloft.net>
If receiving an OGM from a neighbor other than the currently selected
and if it has the same TQ then we are supposed to switch if this
neighbor provides a more symmetric link than the currently selected one.
However this symmetry check currently is broken if the interface of the
neighbor we received the OGM from and the one of the currently selected
neighbor differ: We are currently trying to determine the symmetry of the
link towards the selected router via the link we received the OGM from
instead of just checking via the link towards the currently selected
router.
This leads to way more route switches than necessary and can lead to
permanent route flapping in many common multi interface setups.
This patch fixes this issue by using the right interface for this
symmetry check.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Into function interface_set_mac_addr, the function tt_local_add was
invoked before updating dev->dev_addr. The new MAC address was not
tagged as NoPurge.
Signed-off-by: Def <def@laposte.net>
On some architectures test_bit() can return other values than 0 or 1:
With a generic x86 OpenWrt image in a kvm setup (batadv_)test_bit()
frequently returns -1 for me, leading to batadv_iv_ogm_update_seqnos()
wrongly signaling a protected seqno window.
This patch tries to fix this issue by making batadv_test_bit() return 0
or 1 only.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Acked-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to understand where a broadcast packet is coming from and use
this information to detect not yet announced clients, this patch modifies the
interface_rx() function by passing a new argument: the orig node
corresponding to the node that originated the received packet (if known).
This new argument if not NULL for broadcast packets only (other packets does not
have source field).
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
With the current TT mechanism a new client joining the network is not
immediately able to communicate with other hosts because its MAC address has not
been announced yet. This situation holds until the first OGM containing its
joining event will be spread over the mesh network.
This behaviour can be acceptable in networks where the originator interval is a
small value (e.g. 1sec) but if that value is set to an higher time (e.g. 5secs)
the client could suffer from several malfunctions like DHCP client timeouts,
etc.
This patch adds an early detection mechanism that makes nodes in the network
able to recognise "not yet announced clients" by means of the broadcast packets
they emitted on connection (e.g. ARP or DHCP request). The added client will
then be confirmed upon receiving the OGM claiming it or purged if such OGM
is not received within a fixed amount of time.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
When enabling promiscuous mode, tt queries for other hosts might be
received. Before this patch, "foreign" tt queries were processed like
any other query and thus forwarded to its destination again and thereby
causing a loop.
This patch adds a check to drop foreign tt queries.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
batadv_check_unicast_packet() is needed in batadv_recv_tt_query(), so
move the former to before the latter.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The structure batadv_priv grows everytime a new feature is introduced. It gets
hard to find the parts of the struct that belongs to a specific feature. This
becomes even harder by the fact that not every feature uses a prefix in the
member name.
The variables for bridge loop avoidence, gateway handling, translation table
and visualization server are moved into separate structs that are included in
the bat_priv main struct.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
If this call fails, some of the orig_nodes spaces may have been
resized for the increased number of interface, and some may not.
If we would just continue with the larger number of interfaces,
this would lead to access to not allocated memory later.
We better check the return code, and don't add the interface if
no memory is available. OTOH, keeping some of the orig_nodes
with too much memory allocated should hurt no one (except for
a few too many bytes allocated).
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The batadv_tt_orig_list_entry structure didn't have any refcounting mechanism so
far. This patch introduces it and makes the structure being usable in much more
complex context.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
As much as I'm happy to see LWN links sprinkled through the kernel by the
dozen, this one in particular reflects a very old state of reality; the
associated comment is now incorrect. So just delete it.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
for consistency reasons within the code and with the documentation,
we should always call it "claim" and "unclaim".
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
This is especially useful if there are no claims yet, but we still want
to know which gateways are using bridge loop avoidance in the network.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Memory is allocated for 'tt_change_node' with kmalloc().
'tt_change_node' may go out of scope really being used for anything
(except have a few members initialized) if we hit the 'del:' label.
This patch makes sure we free the memory in that case.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a regression introduced by: 2265c14108
("batman-adv: gateway election code refactoring")
Reported-by: Nicolás Echániz <nicoechaniz@codigosur.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/batman-adv/bridge_loop_avoidance.c
net/batman-adv/bridge_loop_avoidance.h
net/batman-adv/soft-interface.c
net/mac80211/mlme.c
With merge help from Antonio Quartulli (batman-adv) and
Stephen Rothwell (drivers/net/usb/qmi_wwan.c).
The net/mac80211/mlme.c conflict seemed easy enough, accounting for a
conversion to some new tracing macros.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the gateway functionality is used, some broadcast packets (DHCP
requests) may be transmitted as unicast packets. As the bridge loop
avoidance code now only considers the payload Ethernet destination,
it may drop the DHCP request for clients which are claimed by other
backbone gateways, because it falsely infers from the broadcast address
that the right backbone gateway should havehandled the broadcast.
Fix this by checking and delegating the batman-adv packet type used
for transmission.
Reported-by: Guido Iribarren <guidoiribarren@buenosaireslibre.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
The reserved fields in batman-adv packets are not set to a constant value. The
content of these memory regions is leaked unintentionally to the network.
This regression was introduced in 3b27ffb00f
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The "bat_" prefix in the source files implementing the batman-adv sysfs and
debugfs interface doesn't have a special meaning and are only used by these
files and files that implement the actual B.A.T.M.A.N. path finding algorithm.
The prefix is better suited to mark files that are used to implement the main
part of the path finding. All other files should not use it and therefore gets
renamed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The linux Documentation/CodingStyle says that:
* Chapter 12: "inline functions are preferable to macros resembling functions"
* Chapter 12.2: Depending on local variables with a magic name is bad
* Chapter 12.3: Macros with arguments used as l-value are bad
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Instead of adding a new bool argument each time it is needed, it is better (and
simpler) to pass an 8bit flag argument which contains all the needed flags
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
During an OGM-interval (time between two different OGM sendings) the same client
could roam away and then roam back to us. In this case the node would add two
events to the events list (that is going to be sent appended to the next OGM). A
DEL one and an ADD one. Obviously they will only increase the overhead (either in
the air and on the receiver side) and eventually trigger wrong states/events
without producing any real effect.
For this reason we can safely delete any ADD event with its related DEL one.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The vis output doesn't need to be buffered in an character buffer before it can
be send to the userspace program that reads from the vis debug file.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
During the last merge involving translation-table.c something went wrong and two
lines disappeared from translation-table.c. This patch recovers them.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the last conflict resolution involving translation-table.c something went
wrong and a condition in the AP isolation code was reversed. This patch fixes
this problem.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- yet another batch of 'namespace cleaning' patches
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAk/oCnEACgkQpGgxIkP9cwemxACgnCRoebBm9FXzoUfn3hI4YFTu
Hg0AnA6nbPZLQ8uDqdjz45ix1G2T0FnY
=+NOX
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
- yet another batch of 'namespace cleaning' patches
Conflicts:
net/batman-adv/translation-table.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/qmi_wwan.c
net/batman-adv/translation-table.c
net/ipv6/route.c
qmi_wwan.c resolution provided by Bjørn Mork.
batman-adv conflict is dealing merely with the changes
of global function names to have a proper subsystem
prefix.
ipv6's route.c conflict is merely two side-by-side additions
of network namespace methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
bug introduced with cea194d90b11aff7fc289149e4c7f305fad3535a
In the current TT code, when a TT_Response containing a full table is received
from an originator, first the node purges all the clients for that originator in
the global translation-table and then merges the newly received table.
During the purging phase each client deletion is done by means of a call_rcu()
invocation and at the end of this phase the global entry counter for that
originator is set to 0. However the invoked rcu function decreases the global
entry counter for that originator by one too and since the rcu invocation is
likely to be postponed, the node will end up in first setting the counter to 0
and then decreasing it one by one for each deleted client.
This bug leads to having a wrong global entry counter for the related node, say
X. Then when the node with the broken counter will answer to a TT_REQUEST on
behalf of node X, it will create faulty TT_RESPONSE that will generate an
unrecoverable situation on the node that asked for the full table recover.
The non-recoverability is given by the fact that the node with the broken
counter will keep answering on behalf of X because its knowledge about X's state
(ttvn + tt_crc) is correct.
To solve this problem the counter is not explicitly set to 0 anymore and the
counter decrement is performed right before the invocation of call_rcu().
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
bug introduced with 59b699cdee
If the source or destination mac address of an ethernet packet
could not be found in the translation table the packet was
dropped if AP isolation was turned on. This behavior would
make it impossible to send broadcast packets over the mesh as
the broadcast address will never enter the translation table.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Antonio Quartulli <ordex@autistici.org>
batman-adv doesn't follow the style for multiline comments that David S. Miller
prefers. All comments should be reformatted to follow this consistent style to
make the code slightly more readable.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Antonio Quartulli