To allow to access system controller registers from watchdog driver code
add a phandle in the watchdog 'wdt' node. This avoid using arch dependent
operations in driver code.
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Watchdog nodes must use 'watchdog' for node name. When a 'make dtbs_check'
is performed the following warning appears:
wdt@100: $nodename:0: 'wdt@100' does not match '^watchdog(@.*|-[0-9a-f])?$'
Fix this warning up properly renaming the node into 'watchdog'.
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This makes the driver present the clk32k signal if requested.
It is needed to clock the PMU of the BCM4330 WiFi and Bluetooth
module of the CI20 board.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
dtbs_check currently complains that:
arch/mips/boot/dts/img/boston.dts:128.19-178.5: Warning (pci_device_reg):
/pci@14000000/pci2_root@0,0,0: PCI unit address format error,
expected "0,0"
The unit-address format should be '<device>,<function>'.
Fix the unit-address accordingly.
Reported-by: k2ci <kernel-bot@kylinos.cn>
Signed-off-by: Genjian Zhang <zhanggenjian@kylinos.cn>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
On MT7621AT, MT7621DAT, and MT7621ST SoCs, port 5 of the MT7530 switch is
connected to the second MAC of the SoC as a CPU port. Add the port and set
up the second MAC on the bindings. Revert PHY muxing on GB-PC1.
There's an external PHY connected to the second MAC of the SoC on GB-PC2,
therefore, disable port@5 for this device.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The node names should be generic and DT schema expects certain pattern:
mt7621-gnubee-gb-pc1.dtb: gpio-leds: 'power', 'system' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
According to schematics it is PF15 and not PF14 (MIC_SW_EN).
Seems as if it was hidden and not noticed during testing since
there is no sound DT node.
Fixes: 158c774d3c ("MIPS: Ingenic: Add missing nodes for Ingenic SoCs and boards.")
Cc: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Specifying interrupt-parent without a value (in other words, as a bool)
doesn't really mean anything. Remove one such property in the Lantiq
Danube DT, at /sram@1f000000/eiu@101000.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
"make dtbs_check":
arch/mips/boot/dts/mscc/jaguar2_pcb110.dtb: pca9545@70: $nodename:0: 'pca9545@70' does not match '^(i2c-?)?mux'
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
arch/mips/boot/dts/mscc/jaguar2_pcb110.dtb: pca9545@70: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'i2c@0', 'i2c@1', 'i2c@2', 'i2c@3' were unexpected)
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
...
Fix this by renaming PCA9545 nodes to "i2c-mux", to match the I2C bus
multiplexer/switch DT bindings and the Generic Names Recommendation in
the Devicetree Specification.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This is not used by the DSA dt-binding, so remove it from all devicetrees.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Change the labels of the DSA ports to generic naming for switch ports.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The phy-mode property must be defined on the MAC instead of the PHY. Define
phy-mode under gmac1 which the external phy is connected to.
Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Second interrupt can be DMA or EDU one. Specify it explicitly using
interrupt-names property. This matches documented binding.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The reset line is called PWRST#, annotated as "active low" in the
binding documentation, and is driven low and then high by the driver to
reset the chip. However in device tree for CI20 board it was incorrectly
marked as "active high". Fix it.
Because (as far as I know) the ci20.dts is always built in the kernel I
elected not to also add a quirk to gpiolib to force the polarity there.
Fixes: db49ca3857 ("net: davicom: dm9000: switch to using gpiod API")
Reported-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
In the mips CONFIG_SYS_SUPPORTS_ZBOOT kernel, fix the compile error
when using CONFIG_FORTIFY_SOURCE=y
LD vmlinuz
mipsel-openwrt-linux-musl-ld: arch/mips/boot/compressed/decompress.o: in
function `decompress_kernel':
./include/linux/decompress/mm.h:(.text.decompress_kernel+0x177c):
undefined reference to `warn_slowpath_fmt'
kernel test robot helped identify this as related to fortify. The error
appeared with commit 54d9469bc5 ("fortify: Add run-time WARN for
cross-field memcpy()")
Link: https://lore.kernel.org/r/202209161144.x9xSqNQZ-lkp@intel.com/
Resolve this in the same style as commit cfecea6ead ("lib/string:
Move helper functions out of string.c")
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 54d9469bc5 ("fortify: Add run-time WARN for cross-field memcpy()")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Core
----
- Introduce and use a single page frag cache for allocating small skb
heads, clawing back the 10-20% performance regression in UDP flood
test from previous fixes.
- Run packets which already went thru HW coalescing thru SW GRO.
This significantly improves TCP segment coalescing and simplifies
deployments as different workloads benefit from HW or SW GRO.
- Shrink the size of the base zero-copy send structure.
- Move TCP init under a new slow / sleepable version of DO_ONCE().
BPF
---
- Add BPF-specific, any-context-safe memory allocator.
- Add helpers/kfuncs for PKCS#7 signature verification from BPF
programs.
- Define a new map type and related helpers for user space -> kernel
communication over a ring buffer (BPF_MAP_TYPE_USER_RINGBUF).
- Allow targeting BPF iterators to loop through resources of one
task/thread.
- Add ability to call selected destructive functions.
Expose crash_kexec() to allow BPF to trigger a kernel dump.
Use CAP_SYS_BOOT check on the loading process to judge permissions.
- Enable BPF to collect custom hierarchical cgroup stats efficiently
by integrating with the rstat framework.
- Support struct arguments for trampoline based programs.
Only structs with size <= 16B and x86 are supported.
- Invoke cgroup/connect{4,6} programs for unprivileged ICMP ping
sockets (instead of just TCP and UDP sockets).
- Add a helper for accessing CLOCK_TAI for time sensitive network
related programs.
- Support accessing network tunnel metadata's flags.
- Make TCP SYN ACK RTO tunable by BPF programs with TCP Fast Open.
- Add support for writing to Netfilter's nf_conn:mark.
Protocols
---------
- WiFi: more Extremely High Throughput (EHT) and Multi-Link
Operation (MLO) work (802.11be, WiFi 7).
- vsock: improve support for SO_RCVLOWAT.
- SMC: support SO_REUSEPORT.
- Netlink: define and document how to use netlink in a "modern" way.
Support reporting missing attributes via extended ACK.
- IPSec: support collect metadata mode for xfrm interfaces.
- TCPv6: send consistent autoflowlabel in SYN_RECV state
and RST packets.
- TCP: introduce optional per-netns connection hash table to allow
better isolation between namespaces (opt-in, at the cost of memory
and cache pressure).
- MPTCP: support TCP_FASTOPEN_CONNECT.
- Add NEXT-C-SID support in Segment Routing (SRv6) End behavior.
- Adjust IP_UNICAST_IF sockopt behavior for connected UDP sockets.
- Open vSwitch:
- Allow specifying ifindex of new interfaces.
- Allow conntrack and metering in non-initial user namespace.
- TLS: support the Korean ARIA-GCM crypto algorithm.
- Remove DECnet support.
Driver API
----------
- Allow selecting the conduit interface used by each port
in DSA switches, at runtime.
- Ethernet Power Sourcing Equipment and Power Device support.
- Add tc-taprio support for queueMaxSDU parameter, i.e. setting
per traffic class max frame size for time-based packet schedules.
- Support PHY rate matching - adapting between differing host-side
and link-side speeds.
- Introduce QUSGMII PHY mode and 1000BASE-KX interface mode.
- Validate OF (device tree) nodes for DSA shared ports; make
phylink-related properties mandatory on DSA and CPU ports.
Enforcing more uniformity should allow transitioning to phylink.
- Require that flash component name used during update matches one
of the components for which version is reported by info_get().
- Remove "weight" argument from driver-facing NAPI API as much
as possible. It's one of those magic knobs which seemed like
a good idea at the time but is too indirect to use in practice.
- Support offload of TLS connections with 256 bit keys.
New hardware / drivers
----------------------
- Ethernet:
- Microchip KSZ9896 6-port Gigabit Ethernet Switch
- Renesas Ethernet AVB (EtherAVB-IF) Gen4 SoCs
- Analog Devices ADIN1110 and ADIN2111 industrial single pair
Ethernet (10BASE-T1L) MAC+PHY.
- Rockchip RV1126 Gigabit Ethernet (a version of stmmac IP).
- Ethernet SFPs / modules:
- RollBall / Hilink / Turris 10G copper SFPs
- HALNy GPON module
- WiFi:
- CYW43439 SDIO chipset (brcmfmac)
- CYW89459 PCIe chipset (brcmfmac)
- BCM4378 on Apple platforms (brcmfmac)
Drivers
-------
- CAN:
- gs_usb: HW timestamp support
- Ethernet PHYs:
- lan8814: cable diagnostics
- Ethernet NICs:
- Intel (100G):
- implement control of FCS/CRC stripping
- port splitting via devlink
- L2TPv3 filtering offload
- nVidia/Mellanox:
- tunnel offload for sub-functions
- MACSec offload, w/ Extended packet number and replay
window offload
- significantly restructure, and optimize the AF_XDP support,
align the behavior with other vendors
- Huawei:
- configuring DSCP map for traffic class selection
- querying standard FEC statistics
- querying SerDes lane number via ethtool
- Marvell/Cavium:
- egress priority flow control
- MACSec offload
- AMD/SolarFlare:
- PTP over IPv6 and raw Ethernet
- small / embedded:
- ax88772: convert to phylink (to support SFP cages)
- altera: tse: convert to phylink
- ftgmac100: support fixed link
- enetc: standard Ethtool counters
- macb: ZynqMP SGMII dynamic configuration support
- tsnep: support multi-queue and use page pool
- lan743x: Rx IP & TCP checksum offload
- igc: add xdp frags support to ndo_xdp_xmit
- Ethernet high-speed switches:
- Marvell (prestera):
- support SPAN port features (traffic mirroring)
- nexthop object offloading
- Microchip (sparx5):
- multicast forwarding offload
- QoS queuing offload (tc-mqprio, tc-tbf, tc-ets)
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- support RGMII cmode
- NXP (felix):
- standardized ethtool counters
- Microchip (lan966x):
- QoS queuing offload (tc-mqprio, tc-tbf, tc-cbs, tc-ets)
- traffic policing and mirroring
- link aggregation / bonding offload
- QUSGMII PHY mode support
- Qualcomm 802.11ax WiFi (ath11k):
- cold boot calibration support on WCN6750
- support to connect to a non-transmit MBSSID AP profile
- enable remain-on-channel support on WCN6750
- Wake-on-WLAN support for WCN6750
- support to provide transmit power from firmware via nl80211
- support to get power save duration for each client
- spectral scan support for 160 MHz
- MediaTek WiFi (mt76):
- WiFi-to-Ethernet bridging offload for MT7986 chips
- RealTek WiFi (rtw89):
- P2P support
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Gsio
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Introduce and use a single page frag cache for allocating small skb
heads, clawing back the 10-20% performance regression in UDP flood
test from previous fixes.
- Run packets which already went thru HW coalescing thru SW GRO. This
significantly improves TCP segment coalescing and simplifies
deployments as different workloads benefit from HW or SW GRO.
- Shrink the size of the base zero-copy send structure.
- Move TCP init under a new slow / sleepable version of DO_ONCE().
BPF:
- Add BPF-specific, any-context-safe memory allocator.
- Add helpers/kfuncs for PKCS#7 signature verification from BPF
programs.
- Define a new map type and related helpers for user space -> kernel
communication over a ring buffer (BPF_MAP_TYPE_USER_RINGBUF).
- Allow targeting BPF iterators to loop through resources of one
task/thread.
- Add ability to call selected destructive functions. Expose
crash_kexec() to allow BPF to trigger a kernel dump. Use
CAP_SYS_BOOT check on the loading process to judge permissions.
- Enable BPF to collect custom hierarchical cgroup stats efficiently
by integrating with the rstat framework.
- Support struct arguments for trampoline based programs. Only
structs with size <= 16B and x86 are supported.
- Invoke cgroup/connect{4,6} programs for unprivileged ICMP ping
sockets (instead of just TCP and UDP sockets).
- Add a helper for accessing CLOCK_TAI for time sensitive network
related programs.
- Support accessing network tunnel metadata's flags.
- Make TCP SYN ACK RTO tunable by BPF programs with TCP Fast Open.
- Add support for writing to Netfilter's nf_conn:mark.
Protocols:
- WiFi: more Extremely High Throughput (EHT) and Multi-Link Operation
(MLO) work (802.11be, WiFi 7).
- vsock: improve support for SO_RCVLOWAT.
- SMC: support SO_REUSEPORT.
- Netlink: define and document how to use netlink in a "modern" way.
Support reporting missing attributes via extended ACK.
- IPSec: support collect metadata mode for xfrm interfaces.
- TCPv6: send consistent autoflowlabel in SYN_RECV state and RST
packets.
- TCP: introduce optional per-netns connection hash table to allow
better isolation between namespaces (opt-in, at the cost of memory
and cache pressure).
- MPTCP: support TCP_FASTOPEN_CONNECT.
- Add NEXT-C-SID support in Segment Routing (SRv6) End behavior.
- Adjust IP_UNICAST_IF sockopt behavior for connected UDP sockets.
- Open vSwitch:
- Allow specifying ifindex of new interfaces.
- Allow conntrack and metering in non-initial user namespace.
- TLS: support the Korean ARIA-GCM crypto algorithm.
- Remove DECnet support.
Driver API:
- Allow selecting the conduit interface used by each port in DSA
switches, at runtime.
- Ethernet Power Sourcing Equipment and Power Device support.
- Add tc-taprio support for queueMaxSDU parameter, i.e. setting per
traffic class max frame size for time-based packet schedules.
- Support PHY rate matching - adapting between differing host-side
and link-side speeds.
- Introduce QUSGMII PHY mode and 1000BASE-KX interface mode.
- Validate OF (device tree) nodes for DSA shared ports; make
phylink-related properties mandatory on DSA and CPU ports.
Enforcing more uniformity should allow transitioning to phylink.
- Require that flash component name used during update matches one of
the components for which version is reported by info_get().
- Remove "weight" argument from driver-facing NAPI API as much as
possible. It's one of those magic knobs which seemed like a good
idea at the time but is too indirect to use in practice.
- Support offload of TLS connections with 256 bit keys.
New hardware / drivers:
- Ethernet:
- Microchip KSZ9896 6-port Gigabit Ethernet Switch
- Renesas Ethernet AVB (EtherAVB-IF) Gen4 SoCs
- Analog Devices ADIN1110 and ADIN2111 industrial single pair
Ethernet (10BASE-T1L) MAC+PHY.
- Rockchip RV1126 Gigabit Ethernet (a version of stmmac IP).
- Ethernet SFPs / modules:
- RollBall / Hilink / Turris 10G copper SFPs
- HALNy GPON module
- WiFi:
- CYW43439 SDIO chipset (brcmfmac)
- CYW89459 PCIe chipset (brcmfmac)
- BCM4378 on Apple platforms (brcmfmac)
Drivers:
- CAN:
- gs_usb: HW timestamp support
- Ethernet PHYs:
- lan8814: cable diagnostics
- Ethernet NICs:
- Intel (100G):
- implement control of FCS/CRC stripping
- port splitting via devlink
- L2TPv3 filtering offload
- nVidia/Mellanox:
- tunnel offload for sub-functions
- MACSec offload, w/ Extended packet number and replay window
offload
- significantly restructure, and optimize the AF_XDP support,
align the behavior with other vendors
- Huawei:
- configuring DSCP map for traffic class selection
- querying standard FEC statistics
- querying SerDes lane number via ethtool
- Marvell/Cavium:
- egress priority flow control
- MACSec offload
- AMD/SolarFlare:
- PTP over IPv6 and raw Ethernet
- small / embedded:
- ax88772: convert to phylink (to support SFP cages)
- altera: tse: convert to phylink
- ftgmac100: support fixed link
- enetc: standard Ethtool counters
- macb: ZynqMP SGMII dynamic configuration support
- tsnep: support multi-queue and use page pool
- lan743x: Rx IP & TCP checksum offload
- igc: add xdp frags support to ndo_xdp_xmit
- Ethernet high-speed switches:
- Marvell (prestera):
- support SPAN port features (traffic mirroring)
- nexthop object offloading
- Microchip (sparx5):
- multicast forwarding offload
- QoS queuing offload (tc-mqprio, tc-tbf, tc-ets)
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- support RGMII cmode
- NXP (felix):
- standardized ethtool counters
- Microchip (lan966x):
- QoS queuing offload (tc-mqprio, tc-tbf, tc-cbs, tc-ets)
- traffic policing and mirroring
- link aggregation / bonding offload
- QUSGMII PHY mode support
- Qualcomm 802.11ax WiFi (ath11k):
- cold boot calibration support on WCN6750
- support to connect to a non-transmit MBSSID AP profile
- enable remain-on-channel support on WCN6750
- Wake-on-WLAN support for WCN6750
- support to provide transmit power from firmware via nl80211
- support to get power save duration for each client
- spectral scan support for 160 MHz
- MediaTek WiFi (mt76):
- WiFi-to-Ethernet bridging offload for MT7986 chips
- RealTek WiFi (rtw89):
- P2P support"
* tag 'net-next-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1864 commits)
eth: pse: add missing static inlines
once: rename _SLOW to _SLEEPABLE
net: pse-pd: add regulator based PSE driver
dt-bindings: net: pse-dt: add bindings for regulator based PoDL PSE controller
ethtool: add interface to interact with Ethernet Power Equipment
net: mdiobus: search for PSE nodes by parsing PHY nodes.
net: mdiobus: fwnode_mdiobus_register_phy() rework error handling
net: add framework to support Ethernet PSE and PDs devices
dt-bindings: net: phy: add PoDL PSE property
net: marvell: prestera: Propagate nh state from hw to kernel
net: marvell: prestera: Add neighbour cache accounting
net: marvell: prestera: add stub handler neighbour events
net: marvell: prestera: Add heplers to interact with fib_notifier_info
net: marvell: prestera: Add length macros for prestera_ip_addr
net: marvell: prestera: add delayed wq and flush wq on deinit
net: marvell: prestera: Add strict cleanup of fib arbiter
net: marvell: prestera: Add cleanup of allocated fib_nodes
net: marvell: prestera: Add router nexthops ABI
eth: octeon: fix build after netif_napi_add() changes
net/mlx5: E-Switch, Return EBUSY if can't get mode lock
...
Add the missing LEDs for GB-PC2. The ethblack-green, ethblue-green, power
and system LEDs weren't added previously, because they don't exist on the
device schematics. Tests on a GB-PC2 by me and Petr proved otherwise.
The i2c bus cannot be used on GB-PC2 as its pins are wired to LEDs instead,
and GB-PC1 does not use it. Therefore, do not enable it on both devices.
Link: https://github.com/ngiger/GnuBee_Docs/blob/master/GB-PCx/Documents/GB-PC2_V1.1_schematic.pdf
Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address of the external phy on the mdio bus is 5. Update the devicetree
for GB-PC2 accordingly.
Fixes: 5bc148649c ("staging: mt7621-dts: fix GB-PC2 devicetree")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of muxing phy0 of the MT7530 switch, the switch and the phy
will have the same address on the mdio bus, 0. This causes the ethernet
driver to fail since devices on the mdio bus cannot share an address.
Any address can be used for the switch, therefore, change the switch
address to 0x1f.
Suggested-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change phy-mode of gmac1 to rgmii on mt7621.dtsi. Same code path is
followed for delayed rgmii and rgmii phy-mode on mtk_eth_soc.c.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt-parent property is inherited from the ethernet node as it's a
parent node of the switch node. Therefore, remove the unnecessary
interrupt-parent property from the switch node.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the dtc warnings below.
uartlite@c00: $nodename:0: 'uartlite@c00' does not match '^serial(@.*)?$'
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/serial/8250.yaml
uartlite@c00: Unevaluated properties are not allowed ('clock-names' was unexpected)
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/serial/8250.yaml
sdhci@1e130000: $nodename:0: 'sdhci@1e130000' does not match '^mmc(@.*)?$'
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/mmc/mtk-sd.yaml
xhci@1e1c0000: $nodename:0: 'xhci@1e1c0000' does not match '^usb(@.*)?'
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
xhci@1e1c0000: compatible: ['mediatek,mt8173-xhci'] is too short
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
switch0@0: $nodename:0: 'switch0@0' does not match '^(ethernet-)?switch(@.*)?$'
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml
port@1: status:0: 'off' is not one of ['okay', 'disabled', 'reserved']
From schema: /home/arinc9/.local/lib/python3.10/site-packages/dtschema/schemas/dt-core.yaml
port@2: status:0: 'off' is not one of ['okay', 'disabled', 'reserved']
From schema: /home/arinc9/.local/lib/python3.10/site-packages/dtschema/schemas/dt-core.yaml
port@3: status:0: 'off' is not one of ['okay', 'disabled', 'reserved']
From schema: /home/arinc9/.local/lib/python3.10/site-packages/dtschema/schemas/dt-core.yaml
- Change "memc: syscon@5000" to "memc: memory-controller@5000".
- Change "uartlite: uartlite@c00" to "serial0: serial@c00" and remove the
aliases node.
- Remove "clock-names" from the serial0 node. The property doesn't exist on
the 8250.yaml schema.
- Change "sdhci: sdhci@1e130000" to "mmc: mmc@1e130000".
- Change "xhci: xhci@1e1c0000" to "usb: usb@1e1c0000".
- Add "mediatek,mtk-xhci" as the second compatible string on the usb node.
- Change "switch0: switch0@0" to "switch0: switch@0"
- Change "off" to "disabled" for disabled nodes.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TWD is an MFD block that contains timers, watchdog & some clocks / reset
controller.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Rename lantiq dts files with soc name being the prefix, so that the
board dts file can be located easily by soc name, and we also gain
the consistency of naming.
This patch is a preparation for the addition of dts for newer SoCs
(Lantiq ARX100, VRX200 and xRX330).
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
gpio-keys children do not use unit addresses.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This clock is a gate for the TCU hardware block on these SoCs, but
it wasn't included in the device tree since the ingenic-tcu driver
erroneously did not request it.
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for the
USB core, but there are the usual "hot spots" of development activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes. It seems this driver will never
be finished given that the IP core is showing up in zillions
of new devices and each implementation decides to do something
different with it...
- uvc gadget driver updates as more devices start to use and
rely on this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpnZGw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymQhwCeLVANsQjBcL4ys4skl+1In17y28gAn3rEZ7rQ
Yv4uP9zadUqg3Cx0vjgf
=3s5s
-----END PGP SIGNATURE-----
Merge tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for
the USB core, but there are the usual "hot spots" of development
activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes.
It seems this driver will never be finished given that the IP core
is showing up in zillions of new devices and each implementation
decides to do something different with it...
- uvc gadget driver updates as more devices start to use and rely on
this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems"
* tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
USB: new quirk for Dell Gen 2 devices
usb: dwc3: core: Add error log when core soft reset failed
usb: dwc3: gadget: Move null pinter check to proper place
usb: hub: Simplify error and success path in port_over_current_notify
usb: cdns3: allocate TX FIFO size according to composite EP number
usb: dwc3: Fix ep0 handling when getting reset while doing control transfer
usb: Probe EHCI, OHCI controllers asynchronously
usb: isp1760: Fix out-of-bounds array access
xhci: Don't defer primary roothub registration if there is only one roothub
USB: serial: option: add Quectel BG95 modem
USB: serial: pl2303: fix type detection for odd device
xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI
xhci: Remove quirk for over 10 year old evaluation hardware
xhci: prevent U2 link power state if Intel tier policy prevented U1
xhci: use generic command timer for stop endpoint commands.
usb: host: xhci-plat: omit shared hcd if either root hub has no ports
usb: host: xhci-plat: prepare operation w/o shared hcd
usb: host: xhci-plat: create shared hcd after having added main hcd
xhci: prepare for operation w/o shared hcd
xhci: factor out parts of xhci_gen_setup()
...
-----BEGIN PGP SIGNATURE-----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=hTzI
-----END PGP SIGNATURE-----
Merge tag 'mips_5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
"Cleanups and fixes"
* tag 'mips_5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (38 commits)
MIPS: RALINK: Define pci_remap_iospace under CONFIG_PCI_DRIVERS_GENERIC
MIPS: Use memblock_add_node() in early_parse_mem() under CONFIG_NUMA
MIPS: Return -EINVAL if mem parameter is empty in early_parse_mem()
MIPS: Kconfig: Fix indentation and add endif comment
MIPS: bmips: Fix compiler warning observed on W=1 build
MIPS: Rewrite `csum_tcpudp_nofold' in plain C
mips: setup: use strscpy to replace strlcpy
MIPS: Octeon: add SNIC10E board
MIPS: Ingenic: Refresh defconfig for CU1000-Neo and CU1830-Neo.
MIPS: Ingenic: Refresh device tree for Ingenic SoCs and boards.
MIPS: Ingenic: Add PWM nodes for X1830.
MIPS: Octeon: fix typo in comment
MIPS: loongson32: Kconfig: Remove extra space
MIPS: Sibyte: remove unnecessary return variable
MIPS: Use NOKPROBE_SYMBOL() instead of __kprobes annotation
selftests/ftrace: Save kprobe_events to test log
MIPS: tools: no need to initialise statics to 0
MIPS: Loongson: Use hwmon_device_register_with_groups() to register hwmon
MIPS: VR41xx: Drop redundant spinlock initialization
MIPS: smp: optimization for flush_tlb_mm when exiting
...
1.Add SSI nodes for X1000 SoC and X1830 SoC from Ingenic.
2.Refresh SSI related nodes in CU1000-Neo and CU1830-Neo.
3.The X1830 SoC used by the CU1830-Neo and the X1000 SoC
used by the CU1000-Neo are both single-core processors,
therefore the "OST_CLK_PERCPU_TIMER" ABI should not be
used in the OST nodes of the CU1830-Neo and CU1000-Neo,
it is just a coincidence that there is no problem now.
So replace the misused "OST_CLK_PERCPU_TIMER" ABI with
the correct "OST_CLK_EVENT_TIMER" ABI.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Static variables do not need to be initialised to 0, because compiler
will initialise all uninitialised statics to 0. Thus, remove the
unneeded initializations.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Copied from the jz4740 devicetree and trimmed to 5 timers, which
is what the hardware supports.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Tested-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The pinctrl device tree binding will be converted to YAML format. Rename
the pin nodes so they end with "-pins" to match the schema.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The pinctrl device tree binding will be converted to YAML format. Rename
the pin nodes so they end with "-pins" to match the schema.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The pinctrl device tree binding will be converted to YAML format. Rename
the pin nodes so they end with "-pins" to match the schema.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
All pin groups function as gpio unless set otherwise. Therefore, remove
this unnecessary binding.
Tested on UniElec U7621-06-16M on OpenWrt.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Mux the MT7530 switch's phy4 to the SoC's gmac1 on the GB-PC1 devicetree.
This achieves 2 Gbps total bandwidth to the CPU using the second RGMII.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add mdio label to the mdio-bus node to easily refer to it.
Use the newly created label on the GB-PC2 devicetree.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The node names should be generic and SPI NOR dtschema expects "flash".
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Use the new compatible string "ralink,mt7621-pinctrl" for the Ralink MT7621
pinctrl subdriver on mt7621.dtsi.
Each subdriver needs to have a different compatible string. We don't want
the same compatible string to match a different subdriver's pinmux data as
it's not for our SoC.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20220414173916.5552-10-arinc.unal@arinc9.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Here is the big set of staging driver updates for 5.18-rc1.
Loads of tiny cleanups for almost all staging drivers in here, nothing
major at all. Highlights include:
- remove the ashmem Android driver. It is long-dead and if
there are any legacy userspace applications still using it,
the Android kernel images will maintain it, the community
shouldn't care about it anymore
- wfx wifi driver major cleanups. Should be ready to merge out
of staging soon, and will coordinate with the wifi maintainers
after -rc1 is out
- major cleanups and unwinding of the layers of the r8188eu
driver. It's amazing just how many unneeded layers of
abstraction is in there, just when we think it's done, another
is found...
- lots of tiny coding style cleanups in many other staging
drivers.
There will be merge conflict with a fbtft change and the spi driver
changes in your tree, but it's pretty obvious what to do (the function
shouldn't return anything.)
All have been in linux-next for a while with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYkG1cA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylndwCfVhxKnbTYKtOs6UEr5pgPCoQCioUAn0Y2i0TG
4aFeeKUyL8VGdAitL+tp
=E6v7
-----END PGP SIGNATURE-----
Merge tag 'staging-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here is the big set of staging driver updates for 5.18-rc1.
Loads of tiny cleanups for almost all staging drivers in here, nothing
major at all. Highlights include:
- remove the ashmem Android driver. It is long-dead and if there are
any legacy userspace applications still using it, the Android
kernel images will maintain it, the community shouldn't care about
it anymore
- wfx wifi driver major cleanups. Should be ready to merge out of
staging soon, and will coordinate with the wifi maintainers after
-rc1 is out
- major cleanups and unwinding of the layers of the r8188eu driver.
It's amazing just how many unneeded layers of abstraction is in
there, just when we think it's done, another is found...
- lots of tiny coding style cleanups in many other staging drivers.
All have been in linux-next for a while with no reported problems"
* tag 'staging-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (455 commits)
staging: r8188eu: remove unnecessary memset in r8188eu
staging: greybus: introduce pwm_ops::apply
staging: rts5208: Resolve checkpatch.pl issues.
staging: sm750fb: fix naming style
staging: fbtft: Consider type of init sequence values in fbtft_init_display()
staging: fbtft: Constify buf parameter in fbtft_dbg_hex()
staging: mmal-vchiq: clear redundant item named bulk_scratch
mips: dts: ralink: add MT7621 SoC
staging: r8188eu: remove some unused local ieee80211 macros
staging: r8188eu: make rtl8188e_process_phy_info static
staging: r8188eu: remove unused function prototype
staging: r8188eu: remove three unused receive defines
staging: r8188eu: remove unnecessary initializations
staging: rtl8192e: Fix spelling mistake "RESQUEST" -> "REQUEST"
MAINTAINERS: remove the obsolete file entry for staging in ANDROID DRIVERS
staging: r8188eu: proper error handling in rtw_init_drv_sw
staging: r8188eu: call _cancel_timer_ex from _rtw_free_recv_priv
staging: vt6656: Removed unused variable vt3342_vnt_threshold
staging: vt6656: Removed unused variable bb_vga_0
staging: remove ashmem
...
Unit node addresses should not have leading 0x:
Warning (unit_address_format): /nemc@13410000/efuse@d0/eth-mac-addr@0x22: unit name should not have leading "0x"
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The MT7621 system-on-a-chip includes an 880 MHz MIPS1004Kc dual-core CPU,
a 5-port 10/100/1000 switch/PHY and one RGMII.
Add the devicetrees for GB-PC1 and GB-PC2 devices which use MT7621 SoC.
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20220315160149.3617-1-arinc.unal@arinc9.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As done with other image addresses in other architectures, use an
explicit flexible array instead of "address of char", which can trip
bounds checking done by the compiler. Found when building with
-Warray-bounds:
In file included from ./include/linux/byteorder/little_endian.h:5,
from ./arch/mips/include/uapi/asm/byteorder.h:15,
from ./arch/mips/include/asm/bitops.h:21,
from ./include/linux/bitops.h:33,
from ./include/linux/kernel.h:22,
from arch/mips/boot/compressed/decompress.c:13:
arch/mips/boot/compressed/decompress.c: In function 'decompress_kernel':
./include/asm-generic/unaligned.h:14:8: warning: array subscript -1 is outside array bounds of 'unsigned char[1]' [-Warray-bounds]
14 | __pptr->x; \
| ~~~~~~^~~
./include/uapi/linux/byteorder/little_endian.h:35:51: note: in definition of macro '__le32_to_cpu'
35 | #define __le32_to_cpu(x) ((__force __u32)(__le32)(x))
| ^
./include/asm-generic/unaligned.h:32:21: note: in expansion of macro '__get_unaligned_t'
32 | return le32_to_cpu(__get_unaligned_t(__le32, p));
| ^~~~~~~~~~~~~~~~~
arch/mips/boot/compressed/decompress.c:29:37: note: while referencing '__image_end'
29 | extern unsigned char __image_begin, __image_end;
| ^~~~~~~~~~~
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-mips@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>