On Amlogic G12A SoC, the 2,97GHz PLL frequency is not stable enough
to provide a correct 297MHz pixel clock, so switch the PLL base
frequency with a /2 OD when the 297MHz pixel clock is requested.
This solves the issue on G12A and also works fine on GXBB, GXL & GXM.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-2-narmstrong@baylibre.com
DMT monitors does not necessarely report a maximum TMDS clock
in a VSDB EDID extension.
In this case, all modes are wrongly rejected, including
the DRM fallback EDID.
This patch only rejects modes whith clock > max_tmds_clock if
the max_tmds_clock is specified. This will only reject
4:2:0 HDMI2.0 modes, who reports a clock > max_tmds_clock.
Reported-by: Maxime Jourdan <mjourdan@baylibre.com>
Fixes: d7d8fb7046 ("drm/meson: add HDMI div40 TMDS mode")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Maxime Jourdan <mjourdan@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190320081110.1718-1-narmstrong@baylibre.com
meson_drv_unbind() doesn't unregister the IRQ handler, which can lead to
use-after-free if the IRQ fires after unbind:
[ 64.656876] Unable to handle kernel paging request at virtual address ffff000011706dbc
...
[ 64.662001] pc : meson_irq+0x18/0x30 [meson_drm]
I'm assuming that a similar problem could happen on the error path of
bind(), so uninstall the IRQ handler there as well.
Fixes: bbbe775ec5 ("drm: Add support for Amlogic Meson Graphic Controller")
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322152657.13752-2-jean-philippe.brucker@arm.com
meson_drv_bind() registers a meson_drm struct as the device's privdata,
but meson_drv_unbind() tries to retrieve a drm_device. This may cause a
segfault on shutdown:
[ 5194.593429] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000197
...
[ 5194.788850] Call trace:
[ 5194.791349] drm_dev_unregister+0x1c/0x118 [drm]
[ 5194.795848] meson_drv_unbind+0x50/0x78 [meson_drm]
Retrieve the right pointer in meson_drv_unbind().
Fixes: bbbe775ec5 ("drm: Add support for Amlogic Meson Graphic Controller")
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322152657.13752-1-jean-philippe.brucker@arm.com
Now that the DMC register range is no longer in the bindings, remove any
mention towards it and exclusively use the meson-canvas module.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190311105144.7276-3-mjourdan@baylibre.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlxqHJYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGWl8H/jPI4EipzD2GbnjZ
GaFpMBBjcXBaVmoA+Y69so+7BHx1Ql+5GQtqbK0RHJRb9qEPLw3FBhHNjM/N8Sgf
nSrK+GnBZp9s+k/NR/Yf2RacUR3jhz+Q9JEoQd3u9bFUeQyvE8Rf3vgtoBBwFOfz
+t7N1memYVF3asLGWB4e4sP1YVMGfseTQpSPojvM30YWM86Bv+QtSx1AGgHczQIM
kMKealR8ZPelN6JAXgLhQ5opDojBrE4YKB98pwsMDI6abz0Tz2JLFEUTTxsv5XNN
o/Iz+XDoylskEyxN2unNWfHx7Swkvoklog8J/hDg5XlTvipL/WkT66PHBgcGMNvj
BW9GgU8=
=ZizU
-----END PGP SIGNATURE-----
Merge v5.0-rc7 into drm-next
Backmerging for nouveau and imx that needed some fixes for next pulls.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now we support the TMDS Clock > 3.4GHz and support the SCDC Control
operation in the DW-HDMI Controller, we can enable support for the
HDMI2.0 3840x2160@60/50 RGB444 display modes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1549022873-40549-4-git-send-email-narmstrong@baylibre.com
Having the probe helper stuff (which pretty much everyone needs) in
the drm_crtc_helper.h file (which atomic drivers should never need) is
confusing. Split them out.
To make sure I actually achieved the goal here I went through all
drivers. And indeed, all atomic drivers are now free of
drm_crtc_helper.h includes.
v2: Make it compile. There was so much compile fail on arm drivers
that I figured I'll better not include any of the acks on v1.
v3: Massive rebase because i915 has lost a lot of drmP.h includes, but
not all: Through drm_crtc_helper.h > drm_modeset_helper.h -> drmP.h
there was still one, which this patch largely removes. Which means
rolling out lots more includes all over.
This will also conflict with ongoing drmP.h cleanup by others I
expect.
v3: Rebase on top of atomic bochs.
v4: Review from Laurent for bridge/rcar/omap/shmob/core bits:
- (re)move some of the added includes, use the better include files in
other places (all suggested from Laurent adopted unchanged).
- sort alphabetically
v5: Actually try to sort them, and while at it, sort all the ones I
touch.
v6: Rebase onto i915 changes.
v7: Rebase once more.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Acked-by: CK Hu <ck.hu@mediatek.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: virtualization@lists.linux-foundation.org
Cc: etnaviv@lists.freedesktop.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: spice-devel@lists.freedesktop.org
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-tegra@vger.kernel.org
Cc: xen-devel@lists.xen.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190117210334.13234-1-daniel.vetter@ffwll.ch
Since commit 2bcd3ecab7 when switching mode from X11 (ubuntu mate for
example) the display gets blurry, looking like an invalid framebuffer width.
This commit fixed atomic crtc modesetting in a totally wrong way and
introduced a local unnecessary ->enabled crtc state.
This commit reverts the crctc _begin() and _enable() changes and simply
adds drm_atomic_helper_commit_tail_rpm as helper.
Reported-by: Tony McKahan <tonymckahan@gmail.com>
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Fixes: 2bcd3ecab7 ("drm/meson: Fixes for drm_crtc_vblank_on/off support")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[narmstrong: fixed blank line issue from checkpatch]
Link: https://patchwork.freedesktop.org/patch/msgid/20190114153118.8024-1-narmstrong@baylibre.com
In case we are using simplefb or another conflicting framebuffer, make
the call to drm_fb_helper_remove_conflicting_framebuffers()
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181210092853.13050-1-mjourdan@baylibre.com
Add an of_node_put when the result of of_graph_get_remote_port_parent is
not available.
An of_node_put is also needed when meson_probe_remote completes. This was
present at the recursive call, but not in the call from meson_drv_probe.
The semantic match that finds this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@r exists@
local idexpression e;
expression x;
@@
e = of_graph_get_remote_port_parent(...);
... when != x = e
when != true e == NULL
when != of_node_put(e)
when != of_fwnode_handle(e)
(
return e;
|
*return ...;
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1547372691-28324-4-git-send-email-Julia.Lawall@lip6.fr
drm-next has been forwarded to 5.0-rc1, and we need it to apply the damage
helper for dirtyfb series from Noralf Trønnes.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
On the Amlogic GXL & GXM SoCs, a bug occurs on the primary plane when
alpha is used where the alpha is not aligned with the pixel content.
The workaround Amlogic implemented is to reset the OSD1 plane hardware
block each time the plane is (re)enabled, solving the issue.
In the reset, we still need to save the content of 2 registers which
depends on the status of the plane, in addition to reload the scaler
conversion matrix at the same time.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Maxime Jourdan <mjourdan@baylibre.com>
[narmstrong: fixed typo in commit log]
Link: https://patchwork.freedesktop.org/patch/msgid/20181128100734.6536-1-narmstrong@baylibre.com
Core Changes:
- Merge drm_info.c into drm_debugfs.c
- Complete the fake drm_crtc_commit's hw_done/flip_done sooner.
- Remove deprecated drm_obj_ref/unref functions. All drivers use get/put now.
- Decrease stack use of drm_gem_prime_mmap.
- Improve documentation for dumb callbacks.
Driver Changes:
- Add edid support to virtio.
- Wait on implicit fence in meson and sun4i.
- Add support for BGRX8888 to sun4i.
- Preparation patches for sun4i driver to start supporting linear and tiled YUV formats.
- Add support for HDMI 1.4 4k modes to meson, and support for VIC alternate timings.
- Drop custom dumb_map in vkms.
- Small fixes and cleanups to v3d.
-----BEGIN PGP SIGNATURE-----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=JNy2
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2018-11-28' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v4.21:
Core Changes:
- Merge drm_info.c into drm_debugfs.c
- Complete the fake drm_crtc_commit's hw_done/flip_done sooner.
- Remove deprecated drm_obj_ref/unref functions. All drivers use get/put now.
- Decrease stack use of drm_gem_prime_mmap.
- Improve documentation for dumb callbacks.
Driver Changes:
- Add edid support to virtio.
- Wait on implicit fence in meson and sun4i.
- Add support for BGRX8888 to sun4i.
- Preparation patches for sun4i driver to start supporting linear and tiled YUV formats.
- Add support for HDMI 1.4 4k modes to meson, and support for VIC alternate timings.
- Drop custom dumb_map in vkms.
- Small fixes and cleanups to v3d.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/151a3270-b1be-ed75-bd58-6b29d741f592@linux.intel.com
This change is an attempt to handle the alternate clock for the CEA mode.
60Hz vs. 59.94Hz, 30Hz vs 29.97Hz or 24Hz vs 23.97Hz on the Amlogic Meson SoC
DRM Driver pixel clock generation.
The actual clock generation will be moved to the Common Clock framework once
all the video clock are handled by the Amlogic Meson SoC clock driver,
then these alternate timings will be handled in the same time in a cleaner
fashion.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Maxime Jourdan <mjourdan@baylibre.com>
[narmstrong: fix maybe-uninitialized warnings after applying]
Link: https://patchwork.freedesktop.org/patch/msgid/1541501675-3928-1-git-send-email-narmstrong@baylibre.com
Add the timings for the HDMI 1.4 4K modes support :
- 3840x2160@30
- 3840x2160@25
- 3840x2160@24
Since the 297000Hz pixel clock is already managed and the modes are
compatible with the HDMI 1.4 current HDMI PHY+Controller support, only
the missing timings values needs to be added.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Maxime Jourdan <mjourdan@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1541496909-19625-1-git-send-email-narmstrong@baylibre.com
This essential mode for PAL users is missing, so add it.
Fixes: 335e3713af ("drm/meson: Add support for HDMI venc modes and settings")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1542793169-13008-1-git-send-email-christianshewitt@gmail.com
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Since Linux 4.17, calls to drm_crtc_vblank_on/off are mandatory, and we get
a warning when ctrc is disabled :
" driver forgot to call drm_crtc_vblank_off()"
But, the vsync IRQ was not totally disabled due the transient hardware
state and specific interrupt line, thus adding proper IRQ masking from
the HHI system control registers.
The last change fixes a race condition introduced by calling the added
drm_crtc_vblank_on/off when an HPD event occurs from the HDMI connector,
triggering a WARN_ON() in the _atomic_begin() callback when the CRTC
is disabled, thus also triggering a WARN_ON() in drm_vblank_put() :
WARNING: CPU: 0 PID: 1185 at drivers/gpu/drm/meson/meson_crtc.c:157 meson_crtc_atomic_begin+0x78/0x80
[...]
Call trace:
meson_crtc_atomic_begin+0x78/0x80
drm_atomic_helper_commit_planes+0x140/0x218
drm_atomic_helper_commit_tail+0x38/0x80
commit_tail+0x7c/0x80
drm_atomic_helper_commit+0xdc/0x150
drm_atomic_commit+0x54/0x60
restore_fbdev_mode_atomic+0x198/0x238
restore_fbdev_mode+0x6c/0x1c0
drm_fb_helper_restore_fbdev_mode_unlocked+0x7c/0xf0
drm_fb_helper_set_par+0x34/0x60
drm_fb_helper_hotplug_event.part.28+0xb8/0xc8
drm_fbdev_client_hotplug+0xa4/0xe0
drm_client_dev_hotplug+0x90/0xe0
drm_kms_helper_hotplug_event+0x3c/0x48
drm_helper_hpd_irq_event+0x134/0x168
dw_hdmi_top_thread_irq+0x3c/0x50
[...]
WARNING: CPU: 0 PID: 1185 at drivers/gpu/drm/drm_vblank.c:1026 drm_vblank_put+0xb4/0xc8
[...]
Call trace:
drm_vblank_put+0xb4/0xc8
drm_crtc_vblank_put+0x24/0x30
drm_atomic_helper_wait_for_vblanks.part.9+0x130/0x2b8
drm_atomic_helper_commit_tail+0x68/0x80
[...]
The issue is that vblank need to be enabled in any occurrence of :
- atomic_enable()
- atomic_begin() and state->enable == true, which was not the case
Moving the CRTC enable code to a common function and calling in one of
these occurrence solves this race condition and makes sure vblank is
enabled in each call to _atomic_begin() from the HPD event leading to
drm_atomic_helper_commit_planes().
To Summarize :
- Make sure that the CRTC code will call the drm_crtc_vblank_on()/off()
- *Really* mask the Vsync IRQ
- Initialize and enable vblank at the first
atomic_begin()/_atomic_enable()
Cc: stable@vger.kernel.org # 4.17+
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
[fixed typos+added cc for stable]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181122160103.10993-1-narmstrong@baylibre.com
Signed-off-by: Sean Paul <seanpaul@chromium.org>
UAPI Changes:
- Remove syncobj timeline support from drm.
Cross-subsystem Changes:
- Document canvas provider node in the DT bindings.
- Improve documentation for TPO TPG110 DT bindings.
Core Changes:
- Use explicit state in drm atomic functions.
- Add panel quirk for new GPD Win2 firmware.
- Add DRM_FORMAT_XYUV8888.
- Set the default import/export function in prime to drm_gem_prime_import/export.
- Add a separate drm_gem_object_funcs, to stop relying on dev->driver->*gem* functions.
- Make sure that tinydrm sets the virtual address also on imported buffers.
Driver Changes:
- Support active-low data enable signal in sun4i.
- Fix scaling in vc4.
- Use canvas provider node in meson.
- Remove unused variables in sti and qxl and cirrus.
- Add overlay plane support and primary plane scaling to meson.
- i2c fixes in drm/bridge/sii902x
- Fix mailbox read size in rockchip.
- Spelling fix in panel/s6d16d0.
- Remove unnecessary null check from qxl_bo_unref.
- Remove unused arguments from qxl_bo_pin.
- Fix qxl cursor pinning.
-----BEGIN PGP SIGNATURE-----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=elpS
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2018-11-21' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v4.21, part 2:
UAPI Changes:
- Remove syncobj timeline support from drm.
Cross-subsystem Changes:
- Document canvas provider node in the DT bindings.
- Improve documentation for TPO TPG110 DT bindings.
Core Changes:
- Use explicit state in drm atomic functions.
- Add panel quirk for new GPD Win2 firmware.
- Add DRM_FORMAT_XYUV8888.
- Set the default import/export function in prime to drm_gem_prime_import/export.
- Add a separate drm_gem_object_funcs, to stop relying on dev->driver->*gem* functions.
- Make sure that tinydrm sets the virtual address also on imported buffers.
Driver Changes:
- Support active-low data enable signal in sun4i.
- Fix scaling in vc4.
- Use canvas provider node in meson.
- Remove unused variables in sti and qxl and cirrus.
- Add overlay plane support and primary plane scaling to meson.
- i2c fixes in drm/bridge/sii902x
- Fix mailbox read size in rockchip.
- Spelling fix in panel/s6d16d0.
- Remove unnecessary null check from qxl_bo_unref.
- Remove unused arguments from qxl_bo_pin.
- Fix qxl cursor pinning.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9c0409e3-a85f-d2af-b4eb-baf1eb8bbae4@linux.intel.com
UAPI Changes:
- Add syncobj timeline support to drm.
Cross-subsystem Changes:
- Remove shared fence staging in dma-buf's fence object, and allow
reserving more than 1 fence and add more paranoia when debugging.
- Constify infoframe functions in video/hdmi.
Core Changes:
- Add vkms todo, and a lot of assorted doc fixes.
- Drop transitional helpers and convert drivers to use drm_atomic_helper_shutdown().
- Move atomic state helper functions to drm_atomic_state_helper.[ch]
- Refactor drm selftests, and add new tests.
- DP MST atomic state cleanups.
- Drop EXPORT_SYMBOL from drm leases.
- Lease cleanups and fixes.
- Create render node for vgem.
Driver Changes:
- Fix build failure in imx without fbdev emulation.
- Add rotation quirk for GPD win2 panel.
- Add support for various CDTech panels, Banana Pi Panel, DLC1010GIG,
Olimex LCD-O-LinuXino, Samsung S6D16D0, Truly NT35597 WQXGA,
Himax HX8357D, simulated RTSM AEMv8.
- Add dw_hdmi support to rockchip driver.
- Fix YUV support in vc4.
- Fix resource id handling in virtio.
- Make rockchip use dw-mipi-dsi bridge driver, and add dual dsi support.
- Advertise that tinydrm only supports DRM_FORMAT_MOD_LINEAR.
- Convert many drivers to use atomic helpers, and drm_fbdev_generic_setup().
- Add Mali linear tiled formats, and enable them in the Mali-DP driver.
- Add support for H6 DE3 mixer 0, DW HDMI, HDMI PHY and TCON TOP.
- Assorted driver cleanups and fixes.
-----BEGIN PGP SIGNATURE-----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=UV0m
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2018-11-07' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v4.21, part 1:
UAPI Changes:
- Add syncobj timeline support to drm.
Cross-subsystem Changes:
- Remove shared fence staging in dma-buf's fence object, and allow
reserving more than 1 fence and add more paranoia when debugging.
- Constify infoframe functions in video/hdmi.
Core Changes:
- Add vkms todo, and a lot of assorted doc fixes.
- Drop transitional helpers and convert drivers to use drm_atomic_helper_shutdown().
- Move atomic state helper functions to drm_atomic_state_helper.[ch]
- Refactor drm selftests, and add new tests.
- DP MST atomic state cleanups.
- Drop EXPORT_SYMBOL from drm leases.
- Lease cleanups and fixes.
- Create render node for vgem.
Driver Changes:
- Fix build failure in imx without fbdev emulation.
- Add rotation quirk for GPD win2 panel.
- Add support for various CDTech panels, Banana Pi Panel, DLC1010GIG,
Olimex LCD-O-LinuXino, Samsung S6D16D0, Truly NT35597 WQXGA,
Himax HX8357D, simulated RTSM AEMv8.
- Add dw_hdmi support to rockchip driver.
- Fix YUV support in vc4.
- Fix resource id handling in virtio.
- Make rockchip use dw-mipi-dsi bridge driver, and add dual dsi support.
- Advertise that tinydrm only supports DRM_FORMAT_MOD_LINEAR.
- Convert many drivers to use atomic helpers, and drm_fbdev_generic_setup().
- Add Mali linear tiled formats, and enable them in the Mali-DP driver.
- Add support for H6 DE3 mixer 0, DW HDMI, HDMI PHY and TCON TOP.
- Assorted driver cleanups and fixes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/be7ebd91-edd9-8fa4-4286-1c57e3165113@linux.intel.com
This patch adds support for the Primary Plane scaling.
On the Amlogic GX SoCs, the primary plane is used as On-Screen-Display
layer on top of video, and it's needed to keep the OSD layer to a lower
size as the physical display size to :
- lower the memory bandwidth
- lower the OSD rendering
- lower the memory usage
This use-case is used when setting the display mode to 3840x2160 and the
OSD layer is rendered using the GPU. In this case, the GXBB & GXL cannot
work on more than 2000x2000 buffer, thus needing the OSD layer to be kept
at 1920x1080 and upscaled to 3840x2160 in hardware.
The primary plane atomic check still allow 1:1 scaling, allowing native
3840x2160 if needed by user-space applications.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[narmstrong: fixed apply from malformed patch]
Link: https://patchwork.freedesktop.org/patch/msgid/1541497202-20570-4-git-send-email-narmstrong@baylibre.com
In preparation to support the Primary Plane scaling, move the basic
OSD Interlace-Only scaler setup code into the primary plane atomic
update callback and handle the vsync scaler update like the overlay
plane scaling registers update.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1541497202-20570-3-git-send-email-narmstrong@baylibre.com
The Amlogic Meson GX SoCs support an Overlay plane behind the primary
plane for video rendering.
This Overlay plane support various YUV layouts :
- YUYV
- NV12 / NV21
- YUV444 / 422 / 420 / 411 / 410
The scaler supports a wide range of scaling ratios, but for simplicity,
plane atomic check limits the scaling from x5 to /5 in vertical and
horizontal scaling.
The z-order is fixed and always behind the primary plane and cannot be changed.
The scaling parameter algorithm was taken from the Amlogic vendor kernel
code and rewritten to match the atomic universal plane requirements.
The video rendering using this overlay plane support has been tested using
the new Kodi DRM-KMS Prime rendering path along the in-review V4L2 Mem2Mem
Hardware Video Decoder up to 3840x2160 NV12 frames on various display modes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Maxime Jourdan <mjourdan@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1541497202-20570-2-git-send-email-narmstrong@baylibre.com
This is the first step into converting the meson/drm driver to use
the canvas module.
If a canvas provider node is detected in DT, use it. Otherwise,
fall back to what is currently being done.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: added back priv in meson_drv_unbind()]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181105104508.23090-3-mjourdan@baylibre.com
The CMA helper is already using the drm_fb_helper_generic_probe part of
the generic fbdev emulation. This patch makes full use of the generic
fbdev emulation by using its drm_client callbacks. This means that
drm_mode_config_funcs->output_poll_changed and drm_driver->lastclose are
now handled by the emulation code. Additionally fbdev unregister happens
automatically on drm_dev_unregister().
The drm_fbdev_generic_setup() call is put after drm_dev_register() in the
driver. This is done to highlight the fact that fbdev emulation is an
internal client that makes use of the driver, it is not part of the
driver as such. If fbdev setup fails, an error is printed, but the driver
succeeds probing.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180908134648.2582-6-noralf@tronnes.org
Remove the modes timings tables for DMT modes and calculate the HW
paremeters from the modes timings.
Switch the DMT modes pixel clock calculation out of the static frequency
list to a generic calculation from a range of possible PLL dividers.
This patch is an intermediate step towards usage of the Common Clock
Framwework for PLL setup, by reworking the code to have common
sel_pll() function called by the CEA (HDMI) freq setup and the generic
DMT frequencies setup, we should be able to simply call clk_set_rate()
on the PLL clock handle in a near future.
The CEA (HDMI) and CVBS modes needs very specific clock paths that CCF will
never be able to determine by itself, so there is still some work to do for
a full handoff to CCF handling the clocks.
This setup permits setting non-CEA modes like :
- 1600x900-60Hz
- 1280x1024-75Hz
- 1280x1024-60Hz
- 1440x900-60Hz
- 1366x768-60Hz
- 1280x800-60Hz
- 1152x864-75Hz
- 1024x768-75Hz
- 1024x768-70Hz
- 1024x768-60Hz
- 832x624-75Hz
- 800x600-75Hz
- 800x600-72Hz
- 800x600-60Hz
- 640x480-75Hz
- 640x480-73Hz
- 640x480-67Hz
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
[narmstrong: fixed trivial checkpatch issues]
Link: https://patchwork.freedesktop.org/patch/msgid/1531726814-14638-1-git-send-email-narmstrong@baylibre.com
If 'platform_get_resource_byname()' fails, we should release some resources
before leaving, as already done in the other error handling path of the
function.
Fixes: acaa3f13b8 ("drm/meson: Fix potential NULL dereference in meson_drv_bind_master()")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611165335.24542-1-christophe.jaillet@wanadoo.fr
The dw_hdmi_setup_rx_sense exported function should not use struct device
to recover the dw-hdmi context using drvdata, but take struct dw_hdmi
directly like other exported functions.
This caused a regression using Meson DRM on S905X since v4.17-rc1 :
Internal error: Oops: 96000007 [#1] PREEMPT SMP
[...]
CPU: 0 PID: 124 Comm: irq/32-dw_hdmi_ Not tainted 4.17.0-rc7 #2
Hardware name: Libre Technology CC (DT)
[...]
pc : osq_lock+0x54/0x188
lr : __mutex_lock.isra.0+0x74/0x530
[...]
Process irq/32-dw_hdmi_ (pid: 124, stack limit = 0x00000000adf418cb)
Call trace:
osq_lock+0x54/0x188
__mutex_lock_slowpath+0x10/0x18
mutex_lock+0x30/0x38
__dw_hdmi_setup_rx_sense+0x28/0x98
dw_hdmi_setup_rx_sense+0x10/0x18
dw_hdmi_top_thread_irq+0x2c/0x50
irq_thread_fn+0x28/0x68
irq_thread+0x10c/0x1a0
kthread+0x128/0x130
ret_from_fork+0x10/0x18
Code: 34000964 d00050a2 51000484 9135c042 (f864d844)
---[ end trace 945641e1fbbc07da ]---
note: irq/32-dw_hdmi_[124] exited with preempt_count 1
genirq: exiting task "irq/32-dw_hdmi_" (124) is an active IRQ thread (irq 32)
Fixes: eea034af90 ("drm/bridge/synopsys: dw-hdmi: don't clobber drvdata")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1527673438-20643-1-git-send-email-narmstrong@baylibre.com
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJauCZfAAoJEHm+PkMAQRiGWGUH/2rhdQDkoJpYWnjaQkolECG8
MxpGE7nmIIHxQcbSDdHTGJ8IhVm6Z5wZ7ym/PwCDTT043Y1y341sJrIwL2/nTG6d
HVidk8hFvgN6QzlzVAHT3ZZMII/V9Zt+VV5SUYLGnPAVuJNHo/6uzWlTU5g+NTFo
IquFDdQUaGBlkKqby+NoAFnkV1UAIkW0g22cfvPnlO5GMer0gusGyVNvVp7TNj3C
sqj4Hvt3RMDLMNe9RZ2pFTiOD096n8FWpYftZneUTxFImhRV3Jg5MaaYZm9SI3HW
tXrv/LChT/F1mi5Pkx6tkT5Hr8WvcrwDMJ4It1kom10RqWAgjxIR3CMm448ileY=
=YKUG
-----END PGP SIGNATURE-----
Backmerge tag 'v4.16-rc7' into drm-next
Linux 4.16-rc7
This was requested by Daniel, and things were getting
a bit hard to reconcile, most of the conflicts were
trivial though.
platform_get_resource_byname() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource_byname(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1521555630-29284-1-git-send-email-weiyongjun1@huawei.com
This patch adds support for DMT display modes over HDMI.
The modes timings configurations are from the Amlogic Vendor linux tree
and tested over multiples monitors.
Previously only a selected number of CEA modes were supported.
Only these following modes are supported with these changes:
- 640x480@60Hz
- 800x600@60Hz
- 1024x768@60Hz
- 1152x864@75Hz
- 1280x1024@60Hz
- 1600x1200@60Hz
- 1920x1080@60Hz
The associated code to handle the clock rates is also added.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1520935670-14187-1-git-send-email-narmstrong@baylibre.com
drivers, a memory leak on non-blocking commits, a crash on color-eviction.
The is also meson and edid fixes, plus a fix for a doc warning.
-----BEGIN PGP SIGNATURE-----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=555h
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2018-02-21' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Fixes for 4.16. I contains fixes for deadlock on runtime suspend on few
drivers, a memory leak on non-blocking commits, a crash on color-eviction.
The is also meson and edid fixes, plus a fix for a doc warning.
* tag 'drm-misc-fixes-2018-02-21' of git://anongit.freedesktop.org/drm/drm-misc:
drm/tve200: fix kernel-doc documentation comment include
drm/meson: fix vsync buffer update
drm: Handle unexpected holes in color-eviction
drm/edid: Add 6 bpc quirk for CPT panel in Asus UX303LA
drm/amdgpu: Fix deadlock on runtime suspend
drm/radeon: Fix deadlock on runtime suspend
drm/nouveau: Fix deadlock on runtime suspend
drm: Allow determining if current task is output poll worker
workqueue: Allow retrieval of current task's work struct
drm/atomic: Fix memleak on ERESTARTSYS during non-blocking commits
The plane buffer address/stride/height was incorrectly updated in the
plane_atomic_update operation instead of the vsync irq.
This patch delays this operation in the vsync irq along with the
other plane delayed setup.
This issue was masked using legacy framebuffer and X11 modesetting, but
is clearly visible using gbm rendering when buffer is submitted late after
vblank, like using software decoding and OpenGL rendering in Kodi.
With this patch, tearing and other artifacts disappears completely.
Cc: Michal Lazo <michal.lazo@gmail.com>
Fixes: bbbe775ec5 ("drm: Add support for Amlogic Meson Graphic Controller")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1518689976-23292-1-git-send-email-narmstrong@baylibre.com
dw_hdmi shouldn't set drvdata since some drivers might need to store
it's own data there. Rework dw_hdmi in a way to return struct dw_hdmi
instead to store it in drvdata. This way drivers are responsible to
store and pass structure when needed.
Idea was taken from the following commit:
8242ecbd59 ("drm/bridge/synopsys: stop clobbering drvdata")
Cc: p.zabel@pengutronix.de
Cc: Laurent.pinchart@ideasonboard.com
Cc: hjc@rock-chips.com
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214200906.31509-6-jernej.skrabec@siol.net
Parts of PHY code could be useful also for custom PHYs. For example,
Allwinner A83T has custom PHY which is probably Synopsys gen2 PHY
with few additional memory mapped registers, so most of the Synopsys PHY
related code could be reused.
Functions exported here are actually not specific to Synopsys PHYs but
to DWC HDMI controller PHY interface. This means that even if the PHY is
completely custom, i.e. not designed by Synopsys, exported functions can
be useful.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214200906.31509-5-jernej.skrabec@siol.net
Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.
No functional changes as the code already uses crtc_state->mode
to populate the clip, which is also what drm_mode_get_hv_timing()
uses.
Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: linux-amlogic@lists.infradead.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123190502.28449-9-ville.syrjala@linux.intel.com
Reviewed-by: Thierry Reding <treding@nvidia.com>
On reference boards and derivatives, the HDMI Logic is powered by an external
5V regulator.
This regulator was set by the Vendor U-Boot, add optional support for it.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1512561268-29806-4-git-send-email-narmstrong@baylibre.com
drm_plane_helper_check_update() isn't a transitional helper, so let's
rename it to drm_atomic_helper_check_plane_state() and move it into
drm_atomic_helper.c.
v2: Fix the WARNs about plane_state->crtc matching crtc_state->crtc
Cc: Daniel Vetter <daniel@ffwll.ch>
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171101201619.6175-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_plane_helper_check_state() is supposed to do things the atomic way,
so it should not be inspecting crtc->enabled. Rather we should be
looking at crtc_state->enable.
We have a slight complication due to drm_plane_helper_check_update()
reusing drm_plane_helper_check_state() for non-atomic drivers. Thus
we'll have to pass the crtc_state in manally and construct a fake
crtc_state in drm_plane_helper_check_update().
v2: Fix the WARNs about plane_state->crtc matching crtc_state->crtc
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171101201558.6059-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's dead code, the core handles all this directly now.
The only special case is nouveau and tda988x which used one function
for both legacy modeset code and -nv50 atomic world instead of 2
vtables. But amounts to exactly the same.
v2: Rebase over the panel/brideg refactorings in stm/ltdc.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Peter Senna Tschudin <peter.senna@collabora.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Yakir Yang <kuankuan.y@gmail.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Romain Perier <romain.perier@collabora.com>
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rongrong Zou <zourongrong@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Hai Li <hali@codeaurora.org>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-tegra@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Cc: zain wang <wzz@rock-chips.com>
Cc: Baoyou Xie <baoyou.xie@linaro.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725080122.20548-8-daniel.vetter@ffwll.ch
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Philippe Cornu <philippe.cornu@st.com> (on stm)
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
This is the plumbing for supporting fb modifiers on planes. Modifiers
have already been introduced to some extent, but this series will extend
this to allow querying modifiers per plane. Based on this, the client to
enable optimal modifications for framebuffers.
This patch simply allows the DRM drivers to initialize their list of
supported modifiers upon initializing the plane.
v2: A minor addition from Daniel
v3:
* Updated commit message
* s/INVALID/DRM_FORMAT_MOD_INVALID (Liviu)
* Remove some excess newlines (Liviu)
* Update comment for > 64 modifiers (Liviu)
v4: Minor comment adjustments (Liviu)
v5: Some new platforms added due to rebase
v6: Add some missed plane inits (or maybe they're new - who knows at
this point) (Daniel)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Daniel Stone <daniels@collabora.com> (v2)
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Stone <daniels@collabora.com>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Rongrong Zou <zourongrong@gmail.com>
Cc: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Cc: Chen Feng <puck.chen@hisilicon.com>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Partially-Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[seanpaul changed subject prefix and fixed conflict in stm/ltdc.c]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The CRTC .disable() helper operation is deprecated for atomic drivers,
the new .atomic_disable() helper operation being preferred. Convert all
atomic drivers to .atomic_disable() to avoid cargo-cult use of
.disable() in new drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # for sun4i
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> # for mediatek
Acked-by: Alexey Brodkin <abrodkin@synopsys.com> # for arcpgu
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # for atmel-hlcdc
Tested-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Vincent Abriou <vincent.abriou@st.com> # for sti
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> # for vmwgfx
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170630093646.7928-3-laurent.pinchart+renesas@ideasonboard.com
The old state is useful for drivers that need to perform operations at
enable time that depend on the transition between the old and new
states.
While at it, rename the operation to .atomic_enable() to be consistent
with .atomic_disable(), as the .enable() operation is used by atomic
helpers only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # for sun4i
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> # for imx-drm and mediatek
Acked-by: Alexey Brodkin <abrodkin@synopsys.com> # for arcpgu
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # for atmel-hlcdc
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com> # for hdlcd and mali-dp
Acked-by: Stefan Agner <stefan@agner.ch> # for fsl-dcu
Tested-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Vincent Abriou <vincent.abriou@st.com> # for sti
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> # for vmwgfx
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170630093646.7928-2-laurent.pinchart+renesas@ideasonboard.com
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZPdbLAAoJEHm+PkMAQRiGx4wH/1nCjfnl6fE8oJ24/1gEAOUh
biFdqJkYZmlLYHVtYfLm4Ueg4adJdg0wx6qM/4RaAzmQVvLfDV34bc1qBf1+P95G
kVF+osWyXrZo5cTwkwapHW/KNu4VJwAx2D1wrlxKDVG5AOrULH1pYOYGOpApEkZU
4N+q5+M0ce0GJpqtUZX+UnI33ygjdDbBxXoFKsr24B7eA0ouGbAJ7dC88WcaETL+
2/7tT01SvDMo0jBSV0WIqlgXwZ5gp3yPGnklC3F4159Yze6VFrzHMKS/UpPF8o8E
W9EbuzwxsKyXUifX2GY348L1f+47glen/1sedbuKnFhP6E9aqUQQJXvEO7ueQl4=
=m2Gx
-----END PGP SIGNATURE-----
BackMerge tag 'v4.12-rc5' into drm-next
Linux 4.12-rc5 for nouveau fixes
While introducing HDMI support, component matching on connectors node
were bypassed since no driver would actually bind on the DT node.
But when only a CVBS connector is present, only a single node is found
in the graph, but ignored and a NULL match table is given to the
component code.
This code permits bypassing the components framework by binding directly
the DRM driver when no components needs to be loaded.
Fixes: a41e82e6c4 ("drm/meson: Add support for components")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1496067352-8733-1-git-send-email-narmstrong@baylibre.com
Now that we have a callback to check if bridge supports a given mode
we can use it in Synopsys Designware HDMI bridge so that we restrict
the number of probbed modes to the ones we can actually display.
Also, there is no need to use mode_fixup() callback as mode_valid()
will handle the mode validation.
NOTE: I also had to change the pdata declaration of mode_valid
custom callback so that the passed modes are const. I also changed
in the platforms I found. Not even compiled it though.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/3d8d449e4d13d2535fa292c75f5fa931de4a4fa8.1495720737.git.joabreu@synopsys.com
Convert drivers to use the new of_graph_get_remote_node() helper
instead of parsing the endpoint node and then getting the remote device
node. Now drivers can just specify the device node and which
port/endpoint and get back the connected remote device node. The details
of the graph binding are nicely abstracted into the core OF graph code.
This changes some error messages to debug messages (in the graph core).
Graph connections are often "no connects" depending on the particular
board, so we want to avoid spurious messages. Plus the kernel is not a
DT validator.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Liviu Dudau <liviu.dudau@arm.com>
Tested-by: Eric Anholt <eric@anholt.net>
Tested-by: Jyri Sarha <jsarha@ti.com>
Tested by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
The Amlogic Meson GXBB/GXL/GXM SoCs embeds a Synopsys DesignWare HDMI TX
Controller with a custom Bridge + PHY around the Controller.
This driver makes uses of all the custom PHY plat data callbacks and enables
the compatible HDMI modes to be configured as a drm_encoder instance.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch adds support for the supported HDMI Venc modes and add the VPP mux
value to switch to ENCP encoder.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patchs adds support for the supported HDMI modes clocks frequencies.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Since this is managed now by the components code, if CVBS is not available
and HDMI neither, the drm driver won't bind anyway.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch adds support for optional components connected through the
Device Tree endpoints scheme.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Clean the crtc_enable by using the proper crtc_state instead of the state
of the primary plane state data.
Also fix the dependency to commit the plane changes even if enable is called
after the flush.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Less code ftw.
This converts all drivers except the tinydrm helper module. That one
needs more work, since it gets the THIS_MODULE reference from
tinydrm.ko instead of the actual driver module like it should.
Probably needs a similar trick like I used here with generating the
entire struct with a macro.
Cc: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170308141257.12119-24-daniel.vetter@ffwll.ch
The vblank hooks in struct drm_driver are deprecated and only meant for
legacy drivers. For modern drivers with DRIVER_MODESET flag, the hooks
in struct drm_crtc_funcs should be used instead.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1486458995-31018-15-git-send-email-shawnguo@kernel.org
Core code already makes drm_driver.get_vblank_counter hook optional by
letting drm_vblank_no_hw_counter be the default implementation for the
function hook. So the drm_vblank_no_hw_counter assignment in the driver
code becomes redundant and can be removed now.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1486458995-31018-3-git-send-email-shawnguo@kernel.org
Instead of receiving the num_crts as a parameter, we can read it
directly from the mode_config structure. I audited the drivers that
invoke this helper and I believe all of them initialize the mode_config
struct accordingly, prior to calling the fb_helper.
I used the following coccinelle hack to make this transformation, except
for the function headers and comment updates. The first and second
rules are split because I couldn't find a way to remove the unused
temporary variables at the same time I removed the parameter.
// <smpl>
@r@
expression A,B,D,E;
identifier C;
@@
(
- drm_fb_helper_init(A,B,C,D)
+ drm_fb_helper_init(A,B,D)
|
- drm_fbdev_cma_init_with_funcs(A,B,C,D,E)
+ drm_fbdev_cma_init_with_funcs(A,B,D,E)
|
- drm_fbdev_cma_init(A,B,C,D)
+ drm_fbdev_cma_init(A,B,D)
)
@@
expression A,B,C,D,E;
@@
(
- drm_fb_helper_init(A,B,C,D)
+ drm_fb_helper_init(A,B,D)
|
- drm_fbdev_cma_init_with_funcs(A,B,C,D,E)
+ drm_fbdev_cma_init_with_funcs(A,B,D,E)
|
- drm_fbdev_cma_init(A,B,C,D)
+ drm_fbdev_cma_init(A,B,D)
)
@@
identifier r.C;
type T;
expression V;
@@
- T C;
<...
when != C
- C = V;
...>
// </smpl>
Changes since v1:
- Rebased on top of the tip of drm-misc-next.
- Remove mention to sti since a proper fix got merged.
Suggested-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170202162640.27261-1-krisman@collabora.co.uk
The platform driver name is currently "meson" which can lead to some
confusion, this patch renames it to "meson-drm" and removes the owner
attribute since is always added by __platform_driver_register called by the
module_platform_driver() macro.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1486028864-19622-3-git-send-email-narmstrong@baylibre.com
Backmerge Linus master to get the connector locking revert.
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux: (645 commits)
sysctl: fix proc_doulongvec_ms_jiffies_minmax()
Revert "drm/probe-helpers: Drop locking from poll_enable"
MAINTAINERS: add Dan Streetman to zbud maintainers
MAINTAINERS: add Dan Streetman to zswap maintainers
mm: do not export ioremap_page_range symbol for external module
mn10300: fix build error of missing fpu_save()
romfs: use different way to generate fsid for BLOCK or MTD
frv: add missing atomic64 operations
mm, page_alloc: fix premature OOM when racing with cpuset mems update
mm, page_alloc: move cpuset seqcount checking to slowpath
mm, page_alloc: fix fast-path race with cpuset update or removal
mm, page_alloc: fix check for NULL preferred_zone
kernel/panic.c: add missing \n
fbdev: color map copying bounds checking
frv: add atomic64_add_unless()
mm/mempolicy.c: do not put mempolicy before using its nodemask
radix-tree: fix private list warnings
Documentation/filesystems/proc.txt: add VmPin
mm, memcg: do not retry precharge charges
proc: add a schedule point in proc_pid_readdir()
...
This commit fixes the VDAC disabling register write values.
Fixes: bbbe775ec5 ("drm: Add support for Amlogic Meson Graphic Controller")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
When the HDMI output is configured by the bootloader, there is mismatch is the
pipeline configuration and the Vsync interrupt fails to trigger.
This commit disables the HDMI blocks in the probe phase.
Fixes: bbbe775ec5 ("drm: Add support for Amlogic Meson Graphic Controller")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
When no CRTC is associated with the plane, the meson_plane_atomic_check()
call breaks the kernel with an Oops.
Fixes: bbbe775ec5 ("drm: Add support for Amlogic Meson Graphic Controller")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Amlogic Meson Display controller is composed of several components :
DMC|---------------VPU (Video Processing Unit)----------------|------HHI------|
| vd1 _______ _____________ _________________ | |
D |-------| |----| | | | | HDMI PLL |
D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK |
R |-------| |----| Processing | | | | |
| osd2 | | | |---| Enci ----------|----|-----VDAC------|
R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----|
A | osd1 | | | Blenders | | Encl ----------|----|---------------|
M |-------|______|----|____________| |________________| | |
___|__________________________________________________________|_______________|
VIU: Video Input Unit
---------------------
The Video Input Unit is in charge of the pixel scanout from the DDR memory.
It fetches the frames addresses, stride and parameters from the "Canvas" memory.
This part is also in charge of the CSC (Colorspace Conversion).
It can handle 2 OSD Planes and 2 Video Planes.
VPP: Video Post Processing
--------------------------
The Video Post Processing is in charge of the scaling and blending of the
various planes into a single pixel stream.
There is a special "pre-blending" used by the video planes with a dedicated
scaler and a "post-blending" to merge with the OSD Planes.
The OSD planes also have a dedicated scaler for one of the OSD.
VENC: Video Encoders
--------------------
The VENC is composed of the multiple pixel encoders :
- ENCI : Interlace Video encoder for CVBS and Interlace HDMI
- ENCP : Progressive Video Encoder for HDMI
- ENCL : LCD LVDS Encoder
The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock
tree and provides the scanout clock to the VPP and VIU.
The ENCI is connected to a single VDAC for Composite Output.
The ENCI and ENCP are connected to an on-chip HDMI Transceiver.
This driver is a DRM/KMS driver using the following DRM components :
- GEM-CMA
- PRIME-CMA
- Atomic Modesetting
- FBDev-CMA
For the following SoCs :
- GXBB Family (S905)
- GXL Family (S905X, S905D)
- GXM Family (S912)
The current driver only supports the CVBS PAL/NTSC output modes, but the
CRTC/Planes management should support bigger modes.
But Advanced Colorspace Conversion, Scaling and HDMI Modes will be added in
a second time.
The Device Tree bindings makes use of the endpoints video interface definitions
to connect to the optional CVBS and in the future the HDMI Connector nodes.
HDMI Support is planned for a next release.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong