SD spec v5.1 adds discard support. The flows and commands are similar to
mmc, so just set the discard arg in CMD38.
A host which supports DISCARD shall check if the DISCARD_SUPPORT (b313)
is set in the SD_STATUS register. If the card does not support discard,
the host shall not issue DISCARD command, but ERASE command instead.
Post the DISCARD operation, the card may de-allocate the discarded
blocks partially or completely. So the host mustn't make any assumptions
concerning the content of the discarded region. This is unlike ERASE
command, in which the region is guaranteed to contain either '0's or
'1's, depends on the content of DATA_STAT_AFTER_ERASE (b55) in the scr
register.
One more important difference compared to ERASE is the busy timeout
which we will address on the next patch.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
the response type of CMD6 is R1B, when the first CMD6 gets response
CRC error, do retry may get timeout error due to card may still in
busy state, which cause this retry make no sense.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Logical block size is the lowest possible block size that the storage
device can address. Max segment size is often related with controller's
DMA capability. And it is reasonable to align max segment size with
logical block size.
SDHCI sets un-aligned max segment size, and causes ADMA error, so
fix it by aligning max segment size with logical block size.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: linux-block@vger.kernel.org
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case of CQHCI, mrq->cmd may be NULL for data requests (non DCMD).
In such case mmc_should_fail_request is directly dereferencing
mrq->cmd while cmd is NULL.
Fix this by checking for mrq->cmd pointer.
Fixes: 72a5af554d ("mmc: core: Add support for handling CQE requests")
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The only user of mmc_align_data_size() is sdio_align_size(), which is
called from SDIO func drivers to let them distinguish, how to optimally
allocate data buffers.
Let's move mmc_align_data_size() close to the SDIO code as to make it
static, rename it to _sdio_align_size() and simplify its definition, all
with the purpose of clarifying that this is SDIO specific.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
MMC OF parsing functions, which parses various host DT properties, should
stay close to each other. Therefore, let's move mmc_of_parse_voltage()
close to mmc_of_parse() into host.c.
Additionally, there is no reason to build the code only when CONFIG_OF is
set, as there should be stub functions for the OF helpers that is being
used, so let's drop this condition as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The only left user of mmc_regulator_get_ocrmask() is the mmc core itself.
Therefore, let's drop the export and turn it into static.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc regulator helper functions, are placed in the extensive core.c
file. In a step towards trying to create a better structure of files,
avoiding too many lines of code per file, let's move these helpers to a new
file, regulator.c.
Moreover, this within this context it makes sense to also drop the export
of mmc_vddrange_to_ocrmask(), but instead let's make it internal to the mmc
core.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All callers of mmc_wait_for_app_cmd() set the retries in-parameter to
MMC_CMD_RETRIES. This is silly, so let's just drop the in-parameter
altogether, as to simplify the code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_wait_for_app_cmd() is an internal function for sd_ops.c, thus let's
drop the unnecessary export and turn it into static function.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SD specs version 4.x and 5.x have a dedicated slices in the SCR register.
Higher versions will rely on a combination of the existing fields.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In MMC, the discard arg is a read-only ext_csd parameter - set it once
on card init. To be consistent, do that for SD as well even though its
discard arg is always 0x0.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The argument "override_active_level" made it possible to
enforce a specific polarity on the write-protect
GPIO line. All callers in the kernel pass "false" to this
call after I have converted all drivers to use GPIO machine
descriptors, so remove the argument and clean out this.
This kind of polarity inversion should be handled by the
GPIO descriptor inside the GPIO library if needed.
This rids us of one instance of the kludgy calls into
the gpiod_get_raw_value() API.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a plan to build the kernel with -Wimplicit-fallthrough and
this place in the code produced a warning (W=1).
In this particular case rewrote the comment to start with the string "fall
through", so as to match the regular expression expected by GCC. Truncate
the comment slightly to fit the max line length of 80 characters.
This commit remove the following warning:
drivers/mmc/core/host.c:196:14: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In sdio_bus_remove the variable is unneeded,remove it now.
Signed-off-by: wangbo <wang.bo116@zte.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files.
Semantic patch information:
Rationale: DEFINE_SIMPLE_ATTRIBUTE + debugfs_create_file()
imposes some significant overhead as compared to
DEFINE_DEBUGFS_ATTRIBUTE + debugfs_create_file_unsafe().
Generated by: scripts/coccinelle/api/debugfs/debugfs_simple_attr.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
QUEUE_FLAG_NO_SG_MERGE has been killed, so kill BLK_MQ_F_SG_MERGE too.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The kblockd workqueue is created with the WQ_MEM_RECLAIM flag set.
This generates a rescuer thread for that queue that will trigger when
the CPU is under heavy load and collect the uncompleted work.
In the case of mmc, this creates the possibility of a deadlock when
there are multiple partitions on the device as other blk-mq work is
also run on the same queue. For example:
- worker 0 claims the mmc host to work on partition 1
- worker 1 attempts to claim the host for partition 2 but has to wait
for worker 0 to finish
- worker 0 schedules complete_work to release the host
- rescuer thread is triggered after time-out and collects the dangling
work
- rescuer thread attempts to complete the work in order starting with
claim host
- the task to release host is now blocked by a task to claim it and
will never be called
The above results in multiple hung tasks that lead to failures to
mount partitions.
Handling complete_work on a separate workqueue avoids this by keeping
the work completion tasks separate from the other blk-mq work. This
allows the host to be released without getting blocked by other tasks
attempting to claim the host.
Signed-off-by: Zachary Hays <zhays@lexmark.com>
Fixes: 81196976ed ("mmc: block: Add blk-mq support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit 89a5e15bcb ("gpio/mmc/of: Respect polarity in the device
tree") gpiolib-of parses the "cd-gpios" property and flips the polarity
if "cd-inverted" is also set. This results in the "cd-inverted" property
being evaluated twice, which effectively makes it a no-op:
- first in drivers/gpio/gpiolib-of.c (of_xlate_and_get_gpiod_flags) when
setting up the CD GPIO
- then again in drivers/mmc/core/slot-gpio.c (mmc_gpio_get_cd) when
reading the CD GPIO value at runtime
On boards which are using device-tree with the "cd-inverted" property
being set any inserted card are not detected anymore. This is due to the
MMC core treating the CD GPIO with the wrong polarity.
Disable "override_cd_active_level" for the card detection GPIO which is
parsed using mmc_of_parse. This fixes SD card detection on the boards
which are currently using the "cd-inverted" device-tree property (tested
on Meson8b Odroid-C1 and Meson8b EC-100).
This does not remove the CD GPIO inversion logic from the MMC core
because there's at least one driver (sdhci-pci-core for Intel BayTrail
based boards) which still passes "override_cd_active_level = true" to
mmc_gpiod_request_cd(). Due to lack of hardware for testing this is left
untouched.
In the future the GPIO inversion logic for both, card and read-only
detection can be removed once no driver is using it anymore.
Fixes: 89a5e15bcb ("gpio/mmc/of: Respect polarity in the device tree")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Loys Ollivier <loys.ollivier@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Cleanup BKOPS support
- Introduce MMC_CAP_SYNC_RUNTIME_PM
- slot-gpio: Delete legacy slot GPIO handling
MMC host:
- alcor: Add new mmc host driver for Alcor Micro PCI based cardreader
- bcm2835: Several improvements to better recover from errors
- jz4740: Rework and fixup pre|post_req support
- mediatek: Add support for SDIO IRQs
- meson-gx: Improve clock phase management
- meson-gx: Stop descriptor on errors
- mmci: Complete the sbc error path by sending a stop command
- renesas_sdhi/tmio: Fixup reset/resume operations
- renesas_sdhi: Add support for r8a774c0 and R7S9210
- renesas_sdhi: Whitelist R8A77990 SDHI
- renesas_sdhi: Fixup eMMC HS400 compatibility issues for H3 and M3-W
- rtsx_usb_sdmmc: Re-work card detection/removal support
- rtsx_usb_sdmmc: Re-work runtime PM support
- sdhci: Fix timeout loops for some variant drivers
- sdhci: Improve support for error handling due to failing commands
- sdhci-acpi/pci: Disable LED control for Intel BYT-based controllers
- sdhci_am654: Add new SDHCI variant driver to support TI's AM654 SOCs
- sdhci-of-esdhc: Add support for eMMC HS400 mode
- sdhci-omap: Fixup reset support
- sdhci-omap: Workaround errata regarding SDR104/HS200 tuning failures
- sdhci-msm: Fixup sporadic write transfers issues for SDR104/HS200
- sdhci-msm: Fixup dynamical clock gating issues
- various: Complete converting all hosts into using slot GPIO descriptors
Other:
- Move GPIO mmc platform data for mips/sh/arm to GPIO descriptors
- Add new Alcor Micro cardreader PCI driver
- Support runtime power management for memstick rtsx_usb_ms driver
- Use USB remote wakeups for card detection for rtsx_usb misc driver
-----BEGIN PGP SIGNATURE-----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=mB5P
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"This time, this pull request contains changes crossing subsystems and
archs/platforms, which is mainly because of a bigger modernization of
moving from legacy GPIO to GPIO descriptors for MMC (by Linus
Walleij).
Additionally, once again, I am funneling changes to
drivers/misc/cardreader/* and drivers/memstick/* through my MMC tree,
mostly due to that we lack a maintainer for these.
Summary:
MMC core:
- Cleanup BKOPS support
- Introduce MMC_CAP_SYNC_RUNTIME_PM
- slot-gpio: Delete legacy slot GPIO handling
MMC host:
- alcor: Add new mmc host driver for Alcor Micro PCI based cardreader
- bcm2835: Several improvements to better recover from errors
- jz4740: Rework and fixup pre|post_req support
- mediatek: Add support for SDIO IRQs
- meson-gx: Improve clock phase management
- meson-gx: Stop descriptor on errors
- mmci: Complete the sbc error path by sending a stop command
- renesas_sdhi/tmio: Fixup reset/resume operations
- renesas_sdhi: Add support for r8a774c0 and R7S9210
- renesas_sdhi: Whitelist R8A77990 SDHI
- renesas_sdhi: Fixup eMMC HS400 compatibility issues for H3 and M3-W
- rtsx_usb_sdmmc: Re-work card detection/removal support
- rtsx_usb_sdmmc: Re-work runtime PM support
- sdhci: Fix timeout loops for some variant drivers
- sdhci: Improve support for error handling due to failing commands
- sdhci-acpi/pci: Disable LED control for Intel BYT-based controllers
- sdhci_am654: Add new SDHCI variant driver to support TI's AM654 SOCs
- sdhci-of-esdhc: Add support for eMMC HS400 mode
- sdhci-omap: Fixup reset support
- sdhci-omap: Workaround errata regarding SDR104/HS200 tuning failures
- sdhci-msm: Fixup sporadic write transfers issues for SDR104/HS200
- sdhci-msm: Fixup dynamical clock gating issues
- various: Complete converting all hosts into using slot GPIO descriptors
Other:
- Move GPIO mmc platform data for mips/sh/arm to GPIO descriptors
- Add new Alcor Micro cardreader PCI driver
- Support runtime power management for memstick rtsx_usb_ms driver
- Use USB remote wakeups for card detection for rtsx_usb misc driver"
* tag 'mmc-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (99 commits)
mmc: mediatek: Add MMC_CAP_SDIO_IRQ support
mmc: renesas_sdhi_internal_dmac: Whitelist r8a774c0
dt-bindings: mmc: renesas_sdhi: Add r8a774c0 support
mmc: core: Cleanup BKOPS support
mmc: core: Drop redundant check in mmc_send_hpi_cmd()
mmc: sdhci-omap: Workaround errata regarding SDR104/HS200 tuning failures (i929)
dt-bindings: sdhci-omap: Add note for cpu_thermal
mmc: sdhci-acpi: Disable LED control for Intel BYT-based controllers
mmc: sdhci-pci: Disable LED control for Intel BYT-based controllers
mmc: sdhci: Add quirk to disable LED control
mmc: mmci: add variant property to set command stop bit
misc: alcor_pci: fix spelling mistake "invailid" -> "invalid"
mmc: meson-gx: add signal resampling
mmc: meson-gx: align default phase on soc vendor tree
mmc: meson-gx: remove useless lock
mmc: meson-gx: make sure the descriptor is stopped on errors
mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver
dt-bindings: mmc: sdhci-of-arasan: Add deprecated message for AM65
dt-bindings: mmc: sdhci-am654: Document bindings for the host controllers on TI's AM654 SOCs
mmc: sdhci-msm: avoid unused function warning
...
-----BEGIN PGP SIGNATURE-----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=TRdW
-----END PGP SIGNATURE-----
Merge tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"This is the main pull request for block/storage for 4.21.
Larger than usual, it was a busy round with lots of goodies queued up.
Most notable is the removal of the old IO stack, which has been a long
time coming. No new features for a while, everything coming in this
week has all been fixes for things that were previously merged.
This contains:
- Use atomic counters instead of semaphores for mtip32xx (Arnd)
- Cleanup of the mtip32xx request setup (Christoph)
- Fix for circular locking dependency in loop (Jan, Tetsuo)
- bcache (Coly, Guoju, Shenghui)
* Optimizations for writeback caching
* Various fixes and improvements
- nvme (Chaitanya, Christoph, Sagi, Jay, me, Keith)
* host and target support for NVMe over TCP
* Error log page support
* Support for separate read/write/poll queues
* Much improved polling
* discard OOM fallback
* Tracepoint improvements
- lightnvm (Hans, Hua, Igor, Matias, Javier)
* Igor added packed metadata to pblk. Now drives without metadata
per LBA can be used as well.
* Fix from Geert on uninitialized value on chunk metadata reads.
* Fixes from Hans and Javier to pblk recovery and write path.
* Fix from Hua Su to fix a race condition in the pblk recovery
code.
* Scan optimization added to pblk recovery from Zhoujie.
* Small geometry cleanup from me.
- Conversion of the last few drivers that used the legacy path to
blk-mq (me)
- Removal of legacy IO path in SCSI (me, Christoph)
- Removal of legacy IO stack and schedulers (me)
- Support for much better polling, now without interrupts at all.
blk-mq adds support for multiple queue maps, which enables us to
have a map per type. This in turn enables nvme to have separate
completion queues for polling, which can then be interrupt-less.
Also means we're ready for async polled IO, which is hopefully
coming in the next release.
- Killing of (now) unused block exports (Christoph)
- Unification of the blk-rq-qos and blk-wbt wait handling (Josef)
- Support for zoned testing with null_blk (Masato)
- sx8 conversion to per-host tag sets (Christoph)
- IO priority improvements (Damien)
- mq-deadline zoned fix (Damien)
- Ref count blkcg series (Dennis)
- Lots of blk-mq improvements and speedups (me)
- sbitmap scalability improvements (me)
- Make core inflight IO accounting per-cpu (Mikulas)
- Export timeout setting in sysfs (Weiping)
- Cleanup the direct issue path (Jianchao)
- Export blk-wbt internals in block debugfs for easier debugging
(Ming)
- Lots of other fixes and improvements"
* tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block: (364 commits)
kyber: use sbitmap add_wait_queue/list_del wait helpers
sbitmap: add helpers for add/del wait queue handling
block: save irq state in blkg_lookup_create()
dm: don't reuse bio for flushes
nvme-pci: trace SQ status on completions
nvme-rdma: implement polling queue map
nvme-fabrics: allow user to pass in nr_poll_queues
nvme-fabrics: allow nvmf_connect_io_queue to poll
nvme-core: optionally poll sync commands
block: make request_to_qc_t public
nvme-tcp: fix spelling mistake "attepmpt" -> "attempt"
nvme-tcp: fix endianess annotations
nvmet-tcp: fix endianess annotations
nvme-pci: refactor nvme_poll_irqdisable to make sparse happy
nvme-pci: only set nr_maps to 2 if poll queues are supported
nvmet: use a macro for default error location
nvmet: fix comparison of a u16 with -1
blk-mq: enable IO poll if .nr_queues of type poll > 0
blk-mq: change blk_mq_queue_busy() to blk_mq_queue_inflight()
blk-mq: skip zero-queue maps in blk_mq_map_swqueue
...
It's been ~6 years ago since we introduced the BKOPS support for eMMC
cards. The current code is a bit messy and primarily that's because it
prepares to support running BKOPS in an asynchronous mode. However, that
mode has never been fully implemented/enabled. Instead BKOPS is always
executed in synchronously, when the card has reported an urgent BKOPS
level.
For these reasons, let's make the code more readable by dropping the unused
parts. Let's also rename mmc_start_bkops() to mmc_run_bkops(), as to make
it more descriptive.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no point checking if HPI is supported in mmc_send_hpi_cmd() as
mmc_interrupt_hpi(), which is the only caller, already checks if HPI has
been enabled. Therefore, let's drop the check and the corresponding error
path.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some eMMCs from Micron have been reported to need ~800 ms timeout, while
enabling the CACHE ctrl after running sudden power failure tests. The
needed timeout is greater than what the card specifies as its generic CMD6
timeout, through the EXT_CSD register, hence the problem.
Normally we would introduce a card quirk to extend the timeout for these
specific Micron cards. However, due to the rather complicated debug process
needed to find out the error, let's simply use a minimum timeout of 1600ms,
the double of what has been reported, for all cards when enabling CACHE
ctrl.
Reported-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In commit 5320226a05 ("mmc: core: Disable HPI for certain Hynix eMMC
cards"), then intent was to prevent HPI from being used for some eMMC
cards, which didn't properly support it. However, that went too far, as
even BKOPS and CACHE ctrl became prevented. Let's restore those parts and
allow BKOPS and CACHE ctrl even if HPI isn't supported.
Fixes: 5320226a05 ("mmc: core: Disable HPI for certain Hynix eMMC cards")
Cc: Pratibhasagar V <pratibha@codeaurora.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
During a re-initialization of the eMMC card, we may fail to re-enable HPI.
In these cases, that isn't properly reflected in the card->ext_csd.hpi_en
bit, as it keeps being set. This may cause following attempts to use HPI,
even if's not enabled. Let's fix this!
Fixes: eb0d8f135b ("mmc: core: support HPI send command")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To allow mmc host drivers to inform the mmc core about rather using
pm_runtime_put_sync_suspend() instead of pm_runtime_put_autosuspend(),
let's introduce MMC_CAP_SYNC_RUNTIME_PM.
This is especially useful for those mmc host drivers that don't benefit
from using the runtime PM autosuspend feature. Typically this is those that
relies on parent devices to power the card via runtime PM, like some USB
host drivers for example.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All host drivers are converted to look up GPIO descriptors
from device tree, ACPI or machine descriptor tables, so now
we can delete the legacy GPIO handling using hardcoded GPIO
numbers from the kernel.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some eMMC controllers need specific settings for HS400 mode before the
speed mode can be switched to DDR mode, during the HS400 initialization
sequence. For that reason, let's introduce a new host callback,
->hs400_prepare_ddr() and invoked it just before switching to DDR mode.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The only user was converted to fill a sbc command which is the proper
way to do it because of AutoCMD23 feature of some hosts.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The use of string pointers in the MMC slot GPIO context is
pretty dubious, allocating some 2*len extra bytes for each
label of the ro and wp pins.
Tidy this up using kasprintf() with dynamic allocation of
labels for these strings.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When sending out CMD23 in the blk preparation, the comment there
rightfully says:
* However, it is not sufficient to just send CMD23,
* and avoid the final CMD12, as on an error condition
* CMD12 (stop) needs to be sent anyway. This, coupled
* with Auto-CMD23 enhancements provided by some
* hosts, means that the complexity of dealing
* with this is best left to the host. If CMD23 is
* supported by card and host, we'll fill sbc in and let
* the host deal with handling it correctly.
Let's do this behaviour for RPMB as well, and not send CMD23
independently. Otherwise IP cores (like Renesas SDHI) may timeout
because of automatic CMD23/CMD12 handling.
Reported-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Replace the lock in mmc_blk_data that is only used through a pointer
in struct mmc_queue and to protect fields in that structure with
an actual lock in struct mmc_queue.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
mmc uses the block layer struct request pointer to indirect their own
lock to the mmc_queue structure, given that the original lock isn't
reachable outside of block.c. Add a lock pointer to struct mmc_queue
instead and stop overriding the block layer lock which protects fields
entirely separate from the mmc use.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Merge three functions initializing the queue into a single one, and drop
an unused argument for it.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO
lines as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can
use only the fastpatch callbacks to enable/disable irqs
like any normal irqchip, especially the gpiod_lock_as_irq()
has been improved to be callable in fastpath context.
A bunch of rework had to be done to achieve this but it is
a big win since I never liked to restrict this to slowpath.
The only call requireing slowpath was try_module_get() and
this is kept at the .request_resources() slowpath callback.
In the GPIO CEC driver this is a big win sine a single
line is used for both outgoing and incoming traffic, and
this needs to use IRQs for incoming traffic while actively
driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a
"cookie" (struct gpio_array) and a bitmap for setting or
getting multiple GPIO lines at once. This improvement
orginated in a specific need to speed up an OMAP1 driver and
has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot
of checks and code when we want things to go really fast.
The previous code would minimize the number of calls
down to the driver callbacks assuming the CPU speed was
orders of magnitude faster than the I/O latency, but this
assumption was wrong on several platforms: what we needed
to do was to profile and improve the speed on the hot
path of the array functions and this change is now
completed.
- Clean out the painful and hard to grasp BNF experiments
from the device tree bindings. Future approaches are looking
into using JSON schema for this purpose. (Rob Herring
is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and
other contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin
control driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver.
-----BEGIN PGP SIGNATURE-----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=YosT
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.20 series:
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO lines
as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can use only
the fastpatch callbacks to enable/disable irqs like any normal
irqchip, especially the gpiod_lock_as_irq() has been improved to be
callable in fastpath context.
A bunch of rework had to be done to achieve this but it is a big
win since I never liked to restrict this to slowpath. The only call
requireing slowpath was try_module_get() and this is kept at the
.request_resources() slowpath callback. In the GPIO CEC driver this
is a big win sine a single line is used for both outgoing and
incoming traffic, and this needs to use IRQs for incoming traffic
while actively driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a "cookie"
(struct gpio_array) and a bitmap for setting or getting multiple
GPIO lines at once.
This improvement orginated in a specific need to speed up an OMAP1
driver and has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot of checks
and code when we want things to go really fast.
The previous code would minimize the number of calls down to the
driver callbacks assuming the CPU speed was orders of magnitude
faster than the I/O latency, but this assumption was wrong on
several platforms: what we needed to do was to profile and improve
the speed on the hot path of the array functions and this change is
now completed.
- Clean out the painful and hard to grasp BNF experiments from the
device tree bindings. Future approaches are looking into using JSON
schema for this purpose. (Rob Herring is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and other
contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin control
driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver"
* tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (116 commits)
gpio: Clarify kerneldoc on gpiochip_set_chained_irqchip()
gpio: Remove unused 'irqchip' argument to gpiochip_set_cascaded_irqchip()
gpio: Drop parent irq assignment during cascade setup
mmc: pwrseq_simple: Fix incorrect handling of GPIO bitmap
gpio: fix SNPS_CREG kconfig dependency warning
gpiolib: Initialize gdev field before is used
gpio: fix kernel-doc after devres.c file rename
gpio: fix doc string for devm_gpiochip_add_data() to not talk about irq_chip
gpio: syscon: Fix possible NULL ptr usage
gpiolib: Show correct direction from the beginning
pinctrl: msm: Use init_valid_mask exported function
gpiolib: Add init_valid_mask exported function
GPIO: add single-register GPIO via CREG driver
dt-bindings: Document the Synopsys GPIO via CREG bindings
gpio: mockup: use device properties instead of platform_data
gpio: Slightly more helpful debugfs
gpio: omap: Remove set but not used variable 'dev'
gpio: omap: drop omap_gpio_list
Accept partial 'gpio-line-names' property.
gpio: omap: get rid of the conditional PM runtime calls
...
- Introduce a host helper function to share re-tuning progress
MMC host:
- sdhci: Add support for v4 host mode
- sdhci-of-arasan: Add Support for AM654 MMC and PHY
- sdhci-sprd: Add support for Spreadtrum's host controller
- sdhci-tegra: Add support for HS400 enhanced strobe
- sdhci-tegra: Enable UHS/HS200 modes for Tegra186/210
- sdhci-tegra: Add support for HS400 delay line calibration
- sdhci-tegra: Add support for pad calibration
- sdhci-of-dwcmshc: Address 128MB DMA boundary limitation
- sdhci-of-esdhc: Add support for tuning erratum A008171
- sdhci-iproc: Add ACPI support
- mediatek: Add support for MT8183
- mediatek: Improve the support for tuning
- mediatek: Add bus clock control for MT2712
- jz4740: Add support for the JZ4725B
- mmci: Add support for the stm32 sdmmc variant
- mmci: Add support for an optional reset control
- mmci: Add some new variant specific properties/callbacks
- mmci: Re-structure DMA code to prepare for new variants
- renesas_sdhi: Add support for r8a77470, r8a7744 and r8a774a1
- renesas_sdhi_internal_dmac: Whitelist r8a77970 and r8a774a1
- tmio/uniphier-sd: Add new UniPhier SD/eMMC controller driver
- tmio/renesas_sdhi: Deal properly with SCC detection during re-tune
- tmio/renesas_sdhi: Refactor/consolidate clock management
- omap_hsmmc: Drop cover detection and some unused platform data
- dw_mmc-exynos: Enable tuning for more speed modes
- sunxi: Clarify the new timing mode and enable it for the A64 controller
- various: Convert to slot GPIO descriptors
-----BEGIN PGP SIGNATURE-----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=/4yi
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Introduce a host helper function to share re-tuning progress
MMC host:
- sdhci: Add support for v4 host mode
- sdhci-of-arasan: Add Support for AM654 MMC and PHY
- sdhci-sprd: Add support for Spreadtrum's host controller
- sdhci-tegra: Add support for HS400 enhanced strobe
- sdhci-tegra: Enable UHS/HS200 modes for Tegra186/210
- sdhci-tegra: Add support for HS400 delay line calibration
- sdhci-tegra: Add support for pad calibration
- sdhci-of-dwcmshc: Address 128MB DMA boundary limitation
- sdhci-of-esdhc: Add support for tuning erratum A008171
- sdhci-iproc: Add ACPI support
- mediatek: Add support for MT8183
- mediatek: Improve the support for tuning
- mediatek: Add bus clock control for MT2712
- jz4740: Add support for the JZ4725B
- mmci: Add support for the stm32 sdmmc variant
- mmci: Add support for an optional reset control
- mmci: Add some new variant specific properties/callbacks
- mmci: Re-structure DMA code to prepare for new variants
- renesas_sdhi: Add support for r8a77470, r8a7744 and r8a774a1
- renesas_sdhi_internal_dmac: Whitelist r8a77970 and r8a774a1
- tmio/uniphier-sd: Add new UniPhier SD/eMMC controller driver
- tmio/renesas_sdhi: Deal properly with SCC detection during re-tune
- tmio/renesas_sdhi: Refactor/consolidate clock management
- omap_hsmmc: Drop cover detection and some unused platform data
- dw_mmc-exynos: Enable tuning for more speed modes
- sunxi: Clarify the new timing mode and enable it for the A64 controller
- various: Convert to slot GPIO descriptors"
* tag 'mmc-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (129 commits)
mmc: mediatek: drop too much code of tuning method
mmc: mediatek: add MT8183 MMC driver support
mmc: mediatek: tune CMD/DATA together
mmc: mediatek: fix cannot receive new request when msdc_cmd_is_ready fail
mmc: mediatek: fill the actual clock for mmc debugfs
mmc: dt-bindings: add support for MT8183 SoC
mmc: uniphier-sd: avoid using broken DMA RX channel
mmc: uniphier-sd: fix DMA disabling
mmc: tmio: simplify the DMA mode test
mmc: tmio: remove TMIO_MMC_HAVE_HIGH_REG flag
mmc: tmio: move MFD variant reset to a platform hook
mmc: renesas_sdhi: Add r8a77470 SDHI1 support
dt-bindings: mmc: renesas_sdhi: Add r8a77470 support
mmc: mmci: add stm32 sdmmc variant
dt-bindings: mmci: add stm32 sdmmc variant
mmc: mmci: add stm32 sdmmc registers
mmc: mmci: add clock divider for stm32 sdmmc
mmc: mmci: add optional reset property
dt-bindings: mmci: add optional reset property
mmc: mmci: add variant property to not read datacnt
...
-----BEGIN PGP SIGNATURE-----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=LRTT
-----END PGP SIGNATURE-----
Merge tag 'for-4.20/block-20181021' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"This is the main pull request for block changes for 4.20. This
contains:
- Series enabling runtime PM for blk-mq (Bart).
- Two pull requests from Christoph for NVMe, with items such as;
- Better AEN tracking
- Multipath improvements
- RDMA fixes
- Rework of FC for target removal
- Fixes for issues identified by static checkers
- Fabric cleanups, as prep for TCP transport
- Various cleanups and bug fixes
- Block merging cleanups (Christoph)
- Conversion of drivers to generic DMA mapping API (Christoph)
- Series fixing ref count issues with blkcg (Dennis)
- Series improving BFQ heuristics (Paolo, et al)
- Series improving heuristics for the Kyber IO scheduler (Omar)
- Removal of dangerous bio_rewind_iter() API (Ming)
- Apply single queue IPI redirection logic to blk-mq (Ming)
- Set of fixes and improvements for bcache (Coly et al)
- Series closing a hotplug race with sysfs group attributes (Hannes)
- Set of patches for lightnvm:
- pblk trace support (Hans)
- SPDX license header update (Javier)
- Tons of refactoring patches to cleanly abstract the 1.2 and 2.0
specs behind a common core interface. (Javier, Matias)
- Enable pblk to use a common interface to retrieve chunk metadata
(Matias)
- Bug fixes (Various)
- Set of fixes and updates to the blk IO latency target (Josef)
- blk-mq queue number updates fixes (Jianchao)
- Convert a bunch of drivers from the old legacy IO interface to
blk-mq. This will conclude with the removal of the legacy IO
interface itself in 4.21, with the rest of the drivers (me, Omar)
- Removal of the DAC960 driver. The SCSI tree will introduce two
replacement drivers for this (Hannes)"
* tag 'for-4.20/block-20181021' of git://git.kernel.dk/linux-block: (204 commits)
block: setup bounce bio_sets properly
blkcg: reassociate bios when make_request() is called recursively
blkcg: fix edge case for blk_get_rl() under memory pressure
nvme-fabrics: move controller options matching to fabrics
nvme-rdma: always have a valid trsvcid
mtip32xx: fully switch to the generic DMA API
rsxx: switch to the generic DMA API
umem: switch to the generic DMA API
sx8: switch to the generic DMA API
sx8: remove dead IF_64BIT_DMA_IS_POSSIBLE code
skd: switch to the generic DMA API
ubd: remove use of blk_rq_map_sg
nvme-pci: remove duplicate check
drivers/block: Remove DAC960 driver
nvme-pci: fix hot removal during error handling
nvmet-fcloop: suppress a compiler warning
nvme-core: make implicit seed truncation explicit
nvmet-fc: fix kernel-doc headers
nvme-fc: rework the request initialization code
nvme-fc: introduce struct nvme_fcp_op_w_sgl
...
Commit b9762bebc6 ("gpiolib: Pass bitmaps, not integer arrays, to
get/set array") changed the way GPIO values are passed to
gpiod_get/set_array_value() and friends. The new code introduced into
mmc_pwrseq_simple_set_gpios_value() incorrectly interpretes the 'value'
argument as a bitmap of GPIO values and assigns it directly to the
'values' bitmap variable passed to gpiod_set_array_value_cansleep()
instead of filling that bitmap with bits equal to the 'value' argument.
As a result, only member 0 of the array is handled correctly.
Moreover, wrong assumption is taken about the 'values' bitmap size not
exceding the number of bits of the 'value' argument type.
Fix it.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On some SD cards over SPI, reading with the multiblock read command the last
sector will leave the card in a bad state.
Remove last sectors from the multiblock reading cmd.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sd8686 "libertas" SDIO adapter's power is controlled with WLAN_RST
and WLAN_PD pins -- pretty much the same way as sd8787. Allow building
the power sequencing driver along with the libertas Wi-Fi driver.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The debounce value passed to mmc_gpiod_request_cd() function is in
microseconds, but msecs_to_jiffies() requires the value to be in
miliseconds to properly calculate the delay, so adjust the value stored
in cd_debounce_delay_ms context entry.
Fixes: 1d71926bbd ("mmc: core: Fix debounce time to use microseconds")
Fixes: bfd694d5e2 ("mmc: core: Add tunable delay before detecting card
after card is inserted")
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Update device_add_disk() to take an 'groups' argument so that
individual drivers can register a device with additional sysfs
attributes.
This avoids race condition the driver would otherwise have if these
groups were to be created with sysfs_add_groups().
Signed-off-by: Martin Wilck <martin.wilck@suse.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The debounce value in device tree is in milliseconds but needs to be in
microseconds for mmc_gpiod_request_cd().
Fixes: bfd694d5e2 ("mmc: core: Add tunable delay before detecting card
after card is inserted")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to make use of array info obtained from gpiod_get_array() and
speed up processing of arrays matching single GPIO chip layout, that
information must be passed to get/set array functions. Extend the
functions' API with that additional parameter and update all users.
Pass NULL if a user builds an array itself from single GPIOs.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most users of get/set array functions iterate consecutive bits of data,
usually a single integer, while processing array of results obtained
from, or building an array of values to be passed to those functions.
Save time wasted on those iterations by changing the functions' API to
accept bitmaps.
All current users are updated as well.
More benefits from the change are expected as soon as planned support
for accepting/passing those bitmaps directly from/to respective GPIO
chip callbacks if applicable is implemented.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mmc block driver does not support parallel dispatch of requests. In
normal circumstances, all requests are anyway funneled through a single
work item, so parallel dispatch never happens. However it can happen if
there is no elevator.
Fix that by detecting if a dispatch is in progress and returning busy
(BLK_STS_RESOURCE) in that case
Fixes: 81196976ed ("mmc: block: Add blk-mq support")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_select_hs400es() calls mmc_select_bus_width() which will continue
to set 4bit transfer mode if fail to set 8bit mode. The bus width
should not be set to 4bit in HS400es.
When fail to set 8bit mode, need return error directly for HS400es.
Signed-off-by: Hongjie Fang <hongjiefang@asrmicro.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The last user of mmc_power_save|restore_host() APIs is gone, hence let's
drop them. Drop also the corresponding bus_ops callback,
->power_save|restore() as those becomes redundant.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Eyal Reizer <eyalreizer@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This adds two new HS400 tuning operations:
* hs400_downgrade
* hs400_complete
These supplement the existing HS400 operation:
* prepare_hs400_tuning
This is motivated by a requirement of Renesas SDHI for the following:
1. Disabling SCC before selecting to HS if selection of HS400 has occurred.
This can be done in an implementation of prepare_hs400_tuning_downgrade
2. Updating registers after switching to HS400
This can be done in an implementation of complete_hs400_tuning
If hs400_downgrade or hs400_complete are not implemented then they are not
called. Thus means there should be no affect for existing drivers as none
implemt these ops.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
R1_STATUS(x) now is only used by ioctl_rpmb_card_status_poll(),
which checks all bits as possible. But according to the spec,
bit 17 and bit 18 should be ignored, as well bit 14 which is
reserved(must be set to 0) quoting from the spec and these rule
apply to all places checking the device status. So change
its checking from 0xFFFFE000 to 0xFFF9A000.
As a bonus, we reuse it for mmc_do_erase() as well as
mmc_switch_status_error().
(1) Currently mmc_switch_status_error() doesn't check bit 25, but
it means device is locked but not unlocked by CMD42 prior to any
operations which need check busy, which is also not allowed.
(2) mmc_do_erase() also forgot to to check bit 15, WP_ERASE_SKIP.
The spec says "Only partial address space was erased due to existing
write protected blocks.", which obviously means we should fail this I/O.
Otherwise, the partial erased data stored in nonvalatile flash violates
the data integrity from the view of I/O owner, which probably confuse
it when further used.
So reusing R1_STATUS for them not only improve the readability but also
slove real problems.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit bfd694d5e2 ("mmc: core: Add tunable delay
before detecting card after card is inserted") adds
"u32 cd_debounce_delay_ms" to the last of mmc_gpio
struct and cause "char cd_label[0]" NOT work as string
pointer of card detect label, when "cat /proc/interrupts",
the devname for card detect gpio is incorrect as below:
144: 0 gpio-mxc 22 Edge ▒
161: 0 gpio-mxc 7 Edge ▒
Move the cd_label field down to fix this, and drop the
zero from the array size to prevent future similar bugs,
the result is correct as below:
144: 0 gpio-mxc 22 Edge 2198000.mmc cd
161: 0 gpio-mxc 7 Edge 2190000.mmc cd
Fixes: bfd694d5e2 ("mmc: core: Add tunable delay before detecting card after card is inserted")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Decrease polling rate for erase/trim/discard
- Allow non-sleeping GPIOs for card detect
- Improve mmc block removal path
- Enable support for mmc_sw_reset() for SDIO cards
- Add mmc_sw_reset() to allow users to do a soft reset of the card
- Allow power delay to be tunable via DT
- Allow card detect debounce delay to be tunable via DT
- Enable new quirk to limit clock rate for Marvell 8887 chip
- Don't show eMMC RPMB and BOOT areas in /proc/partitions
- Add capability to avoid 3.3V signaling for fragile HWs
MMC host:
- Improve/fixup support for handle highmem pages
- Remove depends on HAS_DMA in case of platform dependency
- mvsdio: Enable support for erase/trim/discard
- rtsx_usb: Enable support for erase/trim/discard
- renesas_sdhi: Fix WP logic regressions
- renesas_sdhi: Add r8a77965 support
- renesas_sdhi: Add R8A77980 to whitelist
- meson: Add optional support for device reset
- meson: Add support for the Meson-AXG platform
- dw_mmc: Add new driver for BlueField DW variant
- mediatek: Add support for 64G DRAM DMA
- sunxi: Deploy runtime PM support
- jz4740: Add support for JZ4780
- jz4740: Enable support for DT based platforms
- sdhci: Various improvement to timeout handling
- sdhci: Disable support for HS200/HS400/UHS when no 1.8V support
- sdhci-omap: Add support for controller in k2g SoC
- sdhci-omap: Add workarounds for a couple of Erratas
- sdhci-omap: Enable support for generic sdhci DT properties
- sdhci-cadence: Re-send tune request to deal with errata
- sdhci-pci: Fix 3.3V voltage switch for some BYT-based Intel controllers
- sdhci-pci: Avoid 3.3V signaling on some NI 904x
- sdhci-esdhc-imx: Use watermark levels for PIO access
- sdhci-msm: Improve card detection handling
- sdhci-msm: Add support voltage pad switching
-----BEGIN PGP SIGNATURE-----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=MwCT
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Decrease polling rate for erase/trim/discard
- Allow non-sleeping GPIOs for card detect
- Improve mmc block removal path
- Enable support for mmc_sw_reset() for SDIO cards
- Add mmc_sw_reset() to allow users to do a soft reset of the card
- Allow power delay to be tunable via DT
- Allow card detect debounce delay to be tunable via DT
- Enable new quirk to limit clock rate for Marvell 8887 chip
- Don't show eMMC RPMB and BOOT areas in /proc/partitions
- Add capability to avoid 3.3V signaling for fragile HWs
MMC host:
- Improve/fixup support for handle highmem pages
- Remove depends on HAS_DMA in case of platform dependency
- mvsdio: Enable support for erase/trim/discard
- rtsx_usb: Enable support for erase/trim/discard
- renesas_sdhi: Fix WP logic regressions
- renesas_sdhi: Add r8a77965 support
- renesas_sdhi: Add R8A77980 to whitelist
- meson: Add optional support for device reset
- meson: Add support for the Meson-AXG platform
- dw_mmc: Add new driver for BlueField DW variant
- mediatek: Add support for 64G DRAM DMA
- sunxi: Deploy runtime PM support
- jz4740: Add support for JZ4780
- jz4740: Enable support for DT based platforms
- sdhci: Various improvement to timeout handling
- sdhci: Disable support for HS200/HS400/UHS when no 1.8V support
- sdhci-omap: Add support for controller in k2g SoC
- sdhci-omap: Add workarounds for a couple of Erratas
- sdhci-omap: Enable support for generic sdhci DT properties
- sdhci-cadence: Re-send tune request to deal with errata
- sdhci-pci: Fix 3.3V voltage switch for some BYT-based Intel controllers
- sdhci-pci: Avoid 3.3V signaling on some NI 904x
- sdhci-esdhc-imx: Use watermark levels for PIO access
- sdhci-msm: Improve card detection handling
- sdhci-msm: Add support voltage pad switching"
* tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (104 commits)
mmc: renesas_sdhi: really fix WP logic regressions
mmc: mvsdio: Enable MMC_CAP_ERASE
mmc: mvsdio: Respect card busy time out from mmc core
mmc: sdhci-msm: Remove NO_CARD_NO_RESET quirk
mmc: sunxi: Use ifdef rather than __maybe_unused
mmc: mxmmc: Use ifdef rather than __maybe_unused
mmc: mxmmc: include linux/highmem.h
mmc: sunxi: mark PM functions as __maybe_unused
mmc: Throttle calls to MMC_SEND_STATUS during mmc_do_erase()
mmc: au1xmmc: handle highmem pages
mmc: Allow non-sleeping GPIO cd
mmc: sdhci-*: Don't emit error msg if sdhci_add_host() fails
mmc: sd: Define name for default speed dtr
mmc: core: Move calls to ->prepare_hs400_tuning() closer to mmc code
mmc: sdhci-xenon: use match_string() helper
mmc: wbsd: handle highmem pages
mmc: ushc: handle highmem pages
mmc: mxcmmc: handle highmem pages
mmc: atmel-mci: use sg_copy_{from,to}_buffer
mmc: android-goldfish: use sg_copy_{from,to}_buffer
...
These include a significant update of the generic power domains (genpd)
and Operating Performance Points (OPP) frameworks, mostly related to
the introduction of power domain performance levels, cpufreq updates
(new driver for Qualcomm Kryo processors, updates of the existing
drivers, some core fixes, schedutil governor improvements), PCI power
management fixes, ACPI workaround for EC-based wakeup events handling
on resume from suspend-to-idle, and major updates of the turbostat
and pm-graph utilities.
Specifics:
- Introduce power domain performance levels into the the generic
power domains (genpd) and Operating Performance Points (OPP)
frameworks (Viresh Kumar, Rajendra Nayak, Dan Carpenter).
- Fix two issues in the runtime PM framework related to the
initialization and removal of devices using device links (Ulf
Hansson).
- Clean up the initialization of drivers for devices in PM domains
(Ulf Hansson, Geert Uytterhoeven).
- Fix a cpufreq core issue related to the policy sysfs interface
causing CPU online to fail for CPUs sharing one cpufreq policy in
some situations (Tao Wang).
- Make it possible to use platform-specific suspend/resume hooks
in the cpufreq-dt driver and make the Armada 37xx DVFS use that
feature (Viresh Kumar, Miquel Raynal).
- Optimize policy transition notifications in cpufreq (Viresh Kumar).
- Improve the iowait boost mechanism in the schedutil cpufreq
governor (Patrick Bellasi).
- Improve the handling of deferred frequency updates in the
schedutil cpufreq governor (Joel Fernandes, Dietmar Eggemann,
Rafael Wysocki, Viresh Kumar).
- Add a new cpufreq driver for Qualcomm Kryo (Ilia Lin).
- Fix and clean up some cpufreq drivers (Colin Ian King, Dmitry
Osipenko, Doug Smythies, Luc Van Oostenryck, Simon Horman,
Viresh Kumar).
- Fix the handling of PCI devices with the DPM_SMART_SUSPEND flag
set and update stale comments in the PCI core PM code (Rafael
Wysocki).
- Work around an issue related to the handling of EC-based wakeup
events in the ACPI PM core during resume from suspend-to-idle if
the EC has been put into the low-power mode (Rafael Wysocki).
- Improve the handling of wakeup source objects in the PM core (Doug
Berger, Mahendran Ganesh, Rafael Wysocki).
- Update the driver core to prevent deferred probe from breaking
suspend/resume ordering (Feng Kan).
- Clean up the PM core somewhat (Bjorn Helgaas, Ulf Hansson, Rafael
Wysocki).
- Make the core suspend/resume code and cpufreq support the RT patch
(Sebastian Andrzej Siewior, Thomas Gleixner).
- Consolidate the PM QoS handling in cpuidle governors (Rafael
Wysocki).
- Fix a possible crash in the hibernation core (Tetsuo Handa).
- Update the rockchip-io Adaptive Voltage Scaling (AVS) driver
(David Wu).
- Update the turbostat utility (fixes, cleanups, new CPU IDs, new
command line options, built-in "Low Power Idle" counters support,
new POLL and POLL% columns) and add an entry for it to MAINTAINERS
(Len Brown, Artem Bityutskiy, Chen Yu, Laura Abbott, Matt Turner,
Prarit Bhargava, Srinivas Pandruvada).
- Update the pm-graph to version 5.1 (Todd Brandt).
- Update the intel_pstate_tracer utility (Doug Smythies).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=wqBV
-----END PGP SIGNATURE-----
Merge tag 'pm-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These include a significant update of the generic power domains
(genpd) and Operating Performance Points (OPP) frameworks, mostly
related to the introduction of power domain performance levels,
cpufreq updates (new driver for Qualcomm Kryo processors, updates of
the existing drivers, some core fixes, schedutil governor
improvements), PCI power management fixes, ACPI workaround for
EC-based wakeup events handling on resume from suspend-to-idle, and
major updates of the turbostat and pm-graph utilities.
Specifics:
- Introduce power domain performance levels into the the generic
power domains (genpd) and Operating Performance Points (OPP)
frameworks (Viresh Kumar, Rajendra Nayak, Dan Carpenter).
- Fix two issues in the runtime PM framework related to the
initialization and removal of devices using device links (Ulf
Hansson).
- Clean up the initialization of drivers for devices in PM domains
(Ulf Hansson, Geert Uytterhoeven).
- Fix a cpufreq core issue related to the policy sysfs interface
causing CPU online to fail for CPUs sharing one cpufreq policy in
some situations (Tao Wang).
- Make it possible to use platform-specific suspend/resume hooks in
the cpufreq-dt driver and make the Armada 37xx DVFS use that
feature (Viresh Kumar, Miquel Raynal).
- Optimize policy transition notifications in cpufreq (Viresh Kumar).
- Improve the iowait boost mechanism in the schedutil cpufreq
governor (Patrick Bellasi).
- Improve the handling of deferred frequency updates in the schedutil
cpufreq governor (Joel Fernandes, Dietmar Eggemann, Rafael Wysocki,
Viresh Kumar).
- Add a new cpufreq driver for Qualcomm Kryo (Ilia Lin).
- Fix and clean up some cpufreq drivers (Colin Ian King, Dmitry
Osipenko, Doug Smythies, Luc Van Oostenryck, Simon Horman, Viresh
Kumar).
- Fix the handling of PCI devices with the DPM_SMART_SUSPEND flag set
and update stale comments in the PCI core PM code (Rafael Wysocki).
- Work around an issue related to the handling of EC-based wakeup
events in the ACPI PM core during resume from suspend-to-idle if
the EC has been put into the low-power mode (Rafael Wysocki).
- Improve the handling of wakeup source objects in the PM core (Doug
Berger, Mahendran Ganesh, Rafael Wysocki).
- Update the driver core to prevent deferred probe from breaking
suspend/resume ordering (Feng Kan).
- Clean up the PM core somewhat (Bjorn Helgaas, Ulf Hansson, Rafael
Wysocki).
- Make the core suspend/resume code and cpufreq support the RT patch
(Sebastian Andrzej Siewior, Thomas Gleixner).
- Consolidate the PM QoS handling in cpuidle governors (Rafael
Wysocki).
- Fix a possible crash in the hibernation core (Tetsuo Handa).
- Update the rockchip-io Adaptive Voltage Scaling (AVS) driver (David
Wu).
- Update the turbostat utility (fixes, cleanups, new CPU IDs, new
command line options, built-in "Low Power Idle" counters support,
new POLL and POLL% columns) and add an entry for it to MAINTAINERS
(Len Brown, Artem Bityutskiy, Chen Yu, Laura Abbott, Matt Turner,
Prarit Bhargava, Srinivas Pandruvada).
- Update the pm-graph to version 5.1 (Todd Brandt).
- Update the intel_pstate_tracer utility (Doug Smythies)"
* tag 'pm-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (128 commits)
tools/power turbostat: update version number
tools/power turbostat: Add Node in output
tools/power turbostat: add node information into turbostat calculations
tools/power turbostat: remove num_ from cpu_topology struct
tools/power turbostat: rename num_cores_per_pkg to num_cores_per_node
tools/power turbostat: track thread ID in cpu_topology
tools/power turbostat: Calculate additional node information for a package
tools/power turbostat: Fix node and siblings lookup data
tools/power turbostat: set max_num_cpus equal to the cpumask length
tools/power turbostat: if --num_iterations, print for specific number of iterations
tools/power turbostat: Add Cannon Lake support
tools/power turbostat: delete duplicate #defines
x86: msr-index.h: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
tools/power turbostat: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
tools/power turbostat: add POLL and POLL% column
tools/power turbostat: Fix --hide Pk%pc10
tools/power turbostat: Build-in "Low Power Idle" counters support
tools/power turbostat: Don't make man pages executable
tools/power turbostat: remove blank lines
tools/power turbostat: a small C-states dump readability immprovement
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nga/
-----END PGP SIGNATURE-----
Merge tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- clean up how we pass around gfp_t and
blk_mq_req_flags_t (Christoph)
- prepare us to defer scheduler attach (Christoph)
- clean up drivers handling of bounce buffers (Christoph)
- fix timeout handling corner cases (Christoph/Bart/Keith)
- bcache fixes (Coly)
- prep work for bcachefs and some block layer optimizations (Kent).
- convert users of bio_sets to using embedded structs (Kent).
- fixes for the BFQ io scheduler (Paolo/Davide/Filippo)
- lightnvm fixes and improvements (Matias, with contributions from Hans
and Javier)
- adding discard throttling to blk-wbt (me)
- sbitmap blk-mq-tag handling (me/Omar/Ming).
- remove the sparc jsflash block driver, acked by DaveM.
- Kyber scheduler improvement from Jianchao, making it more friendly
wrt merging.
- conversion of symbolic proc permissions to octal, from Joe Perches.
Previously the block parts were a mix of both.
- nbd fixes (Josef and Kevin Vigor)
- unify how we handle the various kinds of timestamps that the block
core and utility code uses (Omar)
- three NVMe pull requests from Keith and Christoph, bringing AEN to
feature completeness, file backed namespaces, cq/sq lock split, and
various fixes
- various little fixes and improvements all over the map
* tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block: (196 commits)
blk-mq: update nr_requests when switching to 'none' scheduler
block: don't use blocking queue entered for recursive bio submits
dm-crypt: fix warning in shutdown path
lightnvm: pblk: take bitmap alloc. out of critical section
lightnvm: pblk: kick writer on new flush points
lightnvm: pblk: only try to recover lines with written smeta
lightnvm: pblk: remove unnecessary bio_get/put
lightnvm: pblk: add possibility to set write buffer size manually
lightnvm: fix partial read error path
lightnvm: proper error handling for pblk_bio_add_pages
lightnvm: pblk: fix smeta write error path
lightnvm: pblk: garbage collect lines with failed writes
lightnvm: pblk: rework write error recovery path
lightnvm: pblk: remove dead function
lightnvm: pass flag on graceful teardown to targets
lightnvm: pblk: check for chunk size before allocating it
lightnvm: pblk: remove unnecessary argument
lightnvm: pblk: remove unnecessary indirection
lightnvm: pblk: return NVM_ error on failed submission
lightnvm: pblk: warn in case of corrupted write buffer
...
* pm-domains:
PM / domains: Improve wording of dev_pm_domain_attach() comment
PM / Domains: Don't return -EEXIST at attach when PM domain exists
spi: Respect all error codes from dev_pm_domain_attach()
soundwire: Respect all error codes from dev_pm_domain_attach()
mmc: sdio: Respect all error codes from dev_pm_domain_attach()
i2c: Respect all error codes from dev_pm_domain_attach()
driver core: Respect all error codes from dev_pm_domain_attach()
amba: Respect all error codes from dev_pm_domain_attach()
PM / Domains: Allow a better error handling of dev_pm_domain_attach()
PM / Domains: Check for existing PM domain in dev_pm_domain_attach()
PM / Domains: Drop redundant code in genpd while attaching devices
PM / Domains: Drop comment in genpd about legacy Samsung DT binding
PM / Domains: Fix error path during attach in genpd
By completing the request entirely in the driver we can remove the
BLK_EH_HANDLED return value and thus the split responsibility between the
driver and the block layer that has been causing trouble.
[While this keeps existing behavior it seems to mismatch the comment,
maintainers please chime in!]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This drastically reduces the rate at which the MMC_SEND_STATUS cmd polls
for completion of the MMC Erase operation. The patch does this by adding
a backoff sleep that starts by sleeping for short intervals (128-256us),
and ramps up to sleeping for 32-64ms.
Even on very quickly completing erase operations, the loop iterates a few
times, so not too much extra latency is added to these commands.
For long running discard operarations, like a full-device secure discard,
this change drops the interrupt rates on my single-core NXP I.MX6UL from
45000/s to about 20/s, and greatly improves system responsiveness.
Signed-off-by: Martin Hicks <mort@bork.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This change uses the appropriate _cansleep or non-sleeping API for
reading GPIO card detect state. This allows users with GPIOs that
never sleep to avoid a warning when certain quirks are present.
The sdhci controller has an SDHCI_QUIRK_NO_CARD_NO_RESET, which
indicates that a controller will not reset properly if no card is
inserted. With this quirk enabled, mmc_get_cd_gpio is called in
several places with a spinlock held and interrupts disabled.
gpiod_get_raw_value_cansleep is not happy with this situation,
and throws out a warning.
For boards that a) use controllers that have this quirk, and b) wire
card detect up to a GPIO that doesn't sleep, this is a spurious warning.
This change silences that warning, at the cost of pushing this problem
down to users that have sleeping GPIOs and controllers with this quirk.
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move the calls to ->prepare_hs400_tuning(), from mmc_retune() into
mmc_hs400_to_hs200(), as it better belongs there, rather than being generic
to all type of cards.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
It's pointless to switch and trace partition type if the current
selected device partition is the same with that one. Moreover, cycled
claiming host associated with mmc_blk_part_switch() could make
mmc_blk_remove() end up waiting for grabbing the context if it's
occupied, which lead requests could still hit the low-level drivers,
if an asynchronous unbind for host drivers happened, as the card hasn't
been set removed in the remove path.
So a simple dd in background:
dd if=/dev/mmcblk0 of=/dev/null bs=512k count=100000 &
and doing unbind then:
echo fe320000.dwmmc > /sys/bus/platform/drivers/dwmmc_rockchip/unbind
could make the console stuck for quite a while depending on the
numbers of requests.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In commit 97548575be ("mmc: block: Convert RPMB to a character device") a
new function `mmc_rpmb_ioctl` was added. The final return is simply
returning a value of `0` instead of propagating the correct return code.
Discovered during a compilation with W=1, silence the following gcc warning
drivers/mmc/core/block.c:2470:6: warning: variable ‘ret’ set but not used
[-Wunused-but-set-variable]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 97548575be ("mmc: block: Convert RPMB to a character device")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The hard-coded 10ms delay in mmc_power_up came from
commit 79bccc5aef ("mmc: increase power up delay"), which said "The TI
controller on Toshiba Tecra M5 needs more time to power up or the cards
will init incorrectly or not at all." But it's too engineering solution
for a special board but force all platforms to wait for that long time,
especially painful for mmc_power_up for eMMC when booting.
However, it's added since 2009, and we can't tell if other platforms
benefit from it. But in practise, the modern hardware are most likely to
have a stable power supply with 1ms after setting it for no matter PMIC
or discrete power. And more importnatly, most regulators implement the
callback of ->set_voltage_time_sel() for regulator core to wait for
specific period of time for the power supply to be stable, which means
once regulator_set_voltage_* return, the power should reach the the
minimum voltage that works for initialization. Of course, if there
are some other ways for host to power the card, we should allow them
to argue a suitable delay as well.
With this patch, we could assign the delay from firmware, or we could
assigne it via ->set_ios() callback from host drivers.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Just set up the show callback in the tty_operations, and use
proc_create_single_data to create the file without additional
boilerplace code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
The limitation of being able to check only for -EPROBE_DEFER from
dev_pm_domain_attach() has been removed. Hence let's respect all error
codes and bail out accordingly.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Switch everyone to blk_get_request_flags, and then rename
blk_get_request_flags to blk_get_request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Let's implement the ->sw_reset() bus ops to allow SDIO func drivers, in
particular, to make a SW reset without doing a full power cycle of the SDIO
card.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Move the corresponding code for setting the initial signal voltage, from
mmc_power_up() into a new function, mmc_set_initial_signal_voltage().
Make the function internally available to the mmc core, as to allow the
following changes to make use of it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
It's rather common that a firmware is loaded into an SDIO func device
memory, by the corresponding SDIO func driver during ->probe() time.
However, to actually start running the new firmware, sometimes a soft reset
(no power cycle) and a re-initialization of the card is needed. This is for
example the case with the Espressif ESP8089 WiFi chips, when connected to
an SDIO interface.
To cope with this scenario, let's add a new exported function,
mmc_sw_reset(), which may be called when a soft reset and re-initialization
of the card are needed.
The mmc_sw_reset() is implemented on top of a new bus ops callback, similar
to how the mmc_hw_reset() has been implemented.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The bus ops ->reset() executes a full HW reset of the card, as the calling
function mmc_hw_reset() also indicates by its name. Let's convert to follow
the similar names, for both the bus ops callback and for the corresponding
bus ops functions, as to clarify the purpose of code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_sdio_init_card() function has a couple of callers. In the
re-initialization cases, some additional reset commands are issued before
mmc_sdio_init_card() is called. As these additional reset commands are the
same, let's move these into a new static function, mmc_sdio_reinit_card()
and call mmc_sdio_init_card() from there. In this way we avoid the open
coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Allow to use tunable delay before detecting card after card is inserted,
which either comes from firmware node, or comes from debounce value
passed on to mmc_gpiod_request_cd(). If the platform doesn't support
debounce, then we fall back to use the debounce period as the delay,
otherwise, it behaves the same as before that a HW debounce(if set) plus
a 200ms hardcode delay before detecting the card.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some SD host controllers cannot handle extended use of 3.3V signaling.
To accommodate these controllers, add a capability that requires us to
negotiate the voltage down from 3.3V during card initialization.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Jennifer Dahm <jennifer.dahm@ni.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch uses limit clock rate quirk to reduce clock rate
for "SDR104" mode on IMX side for Marvell 8887
WiFi + Bluetooth chip side, as Marvell does not recommend
to use SDIO at the speed of higher than 150MHz.
Signed-off-by: Diwakar Sharma <diwakar.sharma@in.bosch.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a quirk to limit clock rate which
can be used to reduce the SDIO clock rate for some
chips with broken UHS.
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since RPMB area is accessible via special ioctl only and boot areas
are unlikely to contain any partitions, exclude them all from listing
in /proc/partitions. This will hide them from various user-level
software (e.g. fdisk), thus avoiding unnecessary access attempts.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The use of stack Variable Length Arrays needs to be avoided, as they
can be a vector for stack exhaustion, which can be both a runtime bug
(kernel Oops) or a security flaw (overwriting memory beyond the
stack). Also, in general, as code evolves it is easy to lose track of
how big a VLA can get. Thus, we can end up having runtime failures
that are hard to debug. As part of the directive[1] to remove all VLAs
from the kernel, and build with -Wvla.
Currently driver is using a VLA declared using the number of descriptors. This
array is used to store integer values and is later used as an argument to
`gpiod_set_array_value_cansleep()` This can be avoided by using
`kmalloc_array()` to allocate memory for the array of integer values. Memory is
free'd before return from function.
>From the code it appears that it is safe to sleep so we can use GFP_KERNEL
(based _cansleep() suffix of function `gpiod_set_array_value_cansleep()`.
It can be expected that this patch will result in a small increase in overhead
due to the use of `kmalloc_array()`
[1] https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RVhK
-----END PGP SIGNATURE-----
Merge tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"It's a pretty quiet round this time, which is nice. This contains:
- series from Bart, cleaning up the way we set/test/clear atomic
queue flags.
- series from Bart, fixing races between gendisk and queue
registration and removal.
- set of bcache fixes and improvements from various folks, by way of
Michael Lyle.
- set of lightnvm updates from Matias, most of it being the 1.2 to
2.0 transition.
- removal of unused DIO flags from Nikolay.
- blk-mq/sbitmap memory ordering fixes from Omar.
- divide-by-zero fix for BFQ from Paolo.
- minor documentation patches from Randy.
- timeout fix from Tejun.
- Alpha "can't write a char atomically" fix from Mikulas.
- set of NVMe fixes by way of Keith.
- bsg and bsg-lib improvements from Christoph.
- a few sed-opal fixes from Jonas.
- cdrom check-disk-change deadlock fix from Maurizio.
- various little fixes, comment fixes, etc from various folks"
* tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block: (139 commits)
blk-mq: Directly schedule q->timeout_work when aborting a request
blktrace: fix comment in blktrace_api.h
lightnvm: remove function name in strings
lightnvm: pblk: remove some unnecessary NULL checks
lightnvm: pblk: don't recover unwritten lines
lightnvm: pblk: implement 2.0 support
lightnvm: pblk: implement get log report chunk
lightnvm: pblk: rename ppaf* to addrf*
lightnvm: pblk: check for supported version
lightnvm: implement get log report chunk helpers
lightnvm: make address conversions depend on generic device
lightnvm: add support for 2.0 address format
lightnvm: normalize geometry nomenclature
lightnvm: complete geo structure with maxoc*
lightnvm: add shorten OCSSD version in geo
lightnvm: add minor version to generic geometry
lightnvm: simplify geometry structure
lightnvm: pblk: refactor init/exit sequences
lightnvm: Avoid validation of default op value
lightnvm: centralize permission check for lightnvm ioctl
...
Upon module load, mmc_block allocates a bus with bus_registeri() in
mmc_blk_init(). This reference never gets freed during module unload, which
leads to subsequent re-insertions of the module fails and a WARN() splat is
triggered.
Fix the bug by dropping the reference for the bus in mmc_blk_exit().
Signed-off-by: Alexander Kappner <agk@godking.net>
Fixes: 97548575be ("mmc: block: Convert RPMB to a character device")
Cc: <stable@vger.kernel.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Update documentation for sdio_claim_irq to downgrade the wording
about doing recursive claims in an IRQ handler from 'must not' to
'should not'. This clarifies that recursive claims are supported,
but not the recommended (best) practice
Signed-off-by: Joel Cunningham <joel.cunningham@garmin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch exports the host capabilities to debugfs
Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
[Harish: Added caps2, moved creation to mmc_add_host_debugfs]
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Certain Micron eMMC v4.5 cards might get broken when HPI feature is used
and hence this patch disables the HPI feature for such buggy cards.
In U-Boot, these cards are reported as
Manufacturer: Micron (ID: 0xFE)
OEM: 0x4E
Name: MMC32G
Revision: 19 (0x13)
Serial: 959241022 Manufact. date: 8/2015 (0x82) CRC: 0x00
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.5
High Capacity: Yes
Capacity: 29.1 GiB
Boot Partition Size: 16 MiB
Bus Width: 8-bit
According to JEDEC JEP106 manufacturer 0xFE is Numonyx, which was bought by
Micron.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Cc: <stable@vger.kernel.org> # 4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
PARTITION_CONFIG is cached in mmc_card->ext_csd.part_config and the
currently active partition in mmc_blk_data->part_curr. These caches do
not always reflect changes if the ioctl call modifies the
PARTITION_CONFIG registers, e.g. by changing BOOT_PARTITION_ENABLE.
Write the PARTITION_CONFIG value extracted from the ioctl call to the
cache and update the currently active partition accordingly. This
ensures that the user space cannot change the values behind the
kernel's back. The next call to mmc_blk_part_switch() will operate on
the data set by the ioctl and reflect the changes appropriately.
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch exports RCA register to sysfs which will help in reading the
disk identification information.
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Variable err would be firstly initialized by the return value of
mmc_sd_switch().
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since we could move card->host->caps & MMC_CAP_4_BIT_DATA
ahead of mmc_sdio_init_uhs_card, in mmc_host_uhs(). So there
we could save this bit to check that. Also, if the process of
sdio_enable_4bit_bus goes wrong, we should bails out early.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per SD specification physical layer v4.0, section 3.9.4, it
says "UHS-I supports only 4-bit mode. Host shall select 4-bit
mode by ACMD6. However mmc_sd_init_uhs_card() still go ahead
to initialize the cards anyway, whether card or host won't
support 4-bit mode.
This breaks the platforms which could support UHS-I mode but on
some certain boards only support 1-bit mode with a UHS-I card inserted,
as all the tuning process is broken due to this. Alternatively, we
should check the return value from mmc_set_bus_width() to see if host
could finish the request to switch the bus width on its side. But that
needs more thing to do than this patch that just bails out early to try
high speed mode if 4-bit mode isn't available for whatever reason. And
this patch could also fix the same problem for sdio since R4_18V_PRESENT
won't be set for ocr when mmc_sdio_init_card() finds mmc_host_uhs()
is false.
Note that this patch doesn't keep the checking of card->scr.sda_spec3
and comparing card->scr.bus_widths with SD_SCR_BUS_WIDTH_4 within
mmc_sd_init_uhs_card() since if the sd cards response with SD_ROCR_S18A,
it definitely supports UHS-I mode, which implicitly means these checkings
are always true.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch has been generated as follows:
for verb in set_unlocked clear_unlocked set clear; do
replace-in-files queue_flag_${verb} blk_queue_flag_${verb%_unlocked} \
$(git grep -lw queue_flag_${verb} drivers block/bsg*)
done
Except for protecting all queue flag changes with the queue lock
this patch does not change any functionality.
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 03dbaa04a2 ("mmc: slot-gpio: Add support to enable irq wake on
cd_irq") enabled wakeup at initialization. However, users also want to
control it from sysfs power/wakeup attribute. That means the driver needs
to check the PM flags before enabling it in the suspend callback. Add
support for that in sdhci-pci, which is the only driver presently using the
MMC_CAP_CD_WAKE flag, and remove the enabling in mmc_gpiod_request_cd_irq()
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 03dbaa04a2 ("mmc: slot-gpio: Add support to enable irq wake on
cd_irq") enabled wakeup at initialization. However drivers may wish to
enable and disable based on different criteria. Add a helper function
mmc_gpio_set_cd_wake() to make it easy for drivers to do that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the max_discard value is zero, the conditional branch that checks the
trim capabilities will never update this value with max_trim.
Change the condition statement to also check the max_discard value in order
to avoid an unnecessary call to mmc_do_calc_max_discard.
Signed-off-by: Sergio Valverde <vlvrdv@gmail.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As the block layer, since the conversion to blkmq, claims the host using a
context, a following nested call to mmc_claim_host(), which isn't using a
context, may hang.
Calling mmc_interrupt_hpi() and mmc_read_bkops_status() via the mmc block
layer, may suffer from this problem, as these functions are calling
mmc_claim|release_host().
Let's fix the problem by removing the calls to mmc_claim|release_host()
from the above mentioned functions and instead make the callers responsible
of claiming/releasing the host. As a matter of fact, the existing callers
already deals with it.
Fixes: 81196976ed ("mmc: block: Add blk-mq support")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Like mmc_can_gpio_cd(), mmc_can_gpio_ro() will also be useful for host
drivers to know whether GPIO write-protect detection is supported.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the MMC_DRV_OP_GET_EXT_CSD request completes successfully, then
ext_csd must be freed, but in one case it was not. Fix that.
Signed-off-by: Liu Changcheng <changcheng.liu@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Weibu F3C MiniPC has an onboard AP6255 module, presenting
two SDIO functions on a single MMC host (Bluetooth/btsdio and
WiFi/brcmfmac), and the mmc layer correctly detects this as
non-removable.
After suspend/resume, the wifi and bluetooth interfaces disappear
and do not get probed again.
The conditions here are:
1. During suspend, we reach mmc_pm_notify()
2. mmc_pm_notify() calls mmc_sdio_pre_suspend() to see if we can
suspend the SDIO host. However, mmc_sdio_pre_suspend() returns
-ENOSYS because btsdio_driver does not have a suspend method.
3. mmc_pm_notify() proceeds to remove the card
4. Upon resume, mmc_rescan() does nothing with this host, because of
the rescan_entered check which aims to only scan a non-removable
device a single time (i.e. during boot).
Fix the loss of functionality by detecting that we are unable to
suspend a non-removable host, so avoid the forced removal in that
case. The comment above this function already indicates that this
code was only intended for removable devices.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_blk_alloc_req() is supposed to return error pointers but there is
one path where we forget to set the error code and accidentally return
NULL. The callers are not expecting that and will have a NULL pointer
dereference.
Fixes: 41e3efd07d ("mmc: block: Simplify cleaning up the queue")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove config option MMC_MQ_DEFAULT and parameter mmc_use_blk_mq, so that
blk-mq must be used always.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_test disables the command queue because none of the tests use the
command queue. However the Reset Test will re-enable it, so disable it in
that case too.
Fixes: 9d4579a85c ("mmc: mmc_test: Disable Command Queue while mmc_test is used")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_test now uses mmc_start_request() to test sending commands during
"ongoing" asynchronous transfers, i.e. tests:
Commands during non-blocking read - use Set Block Count (CMD23)
Commands during non-blocking write - use Set Block Count (CMD23)
mmc_start_request() was not initializing cmd_completion, but cmd_completion
is used by "ongoing" transfers, so move initialization of cmd_completion
into making mmc_start_request().
Fixes: cb39f61e9b ("mmc: core: Export a few functions needed for blkmq support")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Calling getnstimeofday() can suffer from time jumps and from the
y2038 overflow, so it is not appropriate here. Using ktime_get_ts64()
solves both problems. Using ktime_get() with ktime_t timestamps would
also work, but it seems that we mainly want to print the times as
seconds+nanoseconds, so it would require an extra division in the output.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The function mmc_cqe_issue_type is local to the source and does
not need to be in global scope, so make it static.
Cleans up sparse warning:
drivers/mmc/core/queue.c:62:21: warning: symbol 'mmc_cqe_issue_type'
was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
drivers/mmc/core/block.c:2106:9-10: WARNING: return of 0/1 in function 'mmc_blk_status_error' with return type bool
Return statements in functions returning bool should use
true/false instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Fixes:7eb43d537166 ("mmc: block: blk-mq: Stop using legacy recovery")
CC: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The block driver's blk-mq paths do not use mmc_start_areq(). In order to
remove mmc_start_areq() entirely, start by removing it from mmc_test.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
There are only a few things the recovery needs to do. Primarily, it just
needs to:
Determine the number of bytes transferred
Get the card back to transfer state
Determine whether to retry
There are also a couple of additional features:
Reset the card before the last retry
Read one sector at a time
The legacy code spent much effort analyzing command errors, but commands
fail fast, so it is simpler just to give all command errors the same number
of retries.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Set a 10 second timeout for polling write request busy state. Note, mmc
core is setting a 3 second timeout for SD cards, and SDHCI has long had a
10 second software timer to timeout the whole request, so 10 seconds should
be ample.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
According to the specification, total access time is derived from both TAAC
and NSAC, which means the timeout should add both timeout_ns and
timeout_clks. Host drivers do that, so make the block driver do that too.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
The card is required to return to transfer state. Since that is the state
required to start another transfer, check for that state instead of
programming state.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Pedantically, ensure the status is checked for the last time after the full
timeout has passed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Check error bits and save the exception bit when polling card busy.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Make card_busy_detect() accumulate all response error bits. Later patches
will make use of this.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Recovery is simpler to understand if it is only used for errors. Create a
separate function for card polling.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
For blk-mq, add support for completing requests directly in the ->done
callback. That means that error handling and urgent background operations
must be handled by recovery_work in that case.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Add CQE support to the block driver, including:
- optionally using DCMD for flush requests
- "manually" issuing discard requests
- issuing read / write requests to the CQE
- supporting block-layer timeouts
- handling recovery
- supporting re-tuning
CQE offers 25% - 50% better random multi-threaded I/O. There is a slight
(e.g. 2%) drop in sequential read speed but no observable change to sequential
write.
CQE automatically sends the commands to complete requests. However it only
supports reads / writes and so-called "direct commands" (DCMD). Furthermore
DCMD is limited to one command at a time, but discards require 3 commands.
That makes issuing discards through CQE very awkward, but some CQE's don't
support DCMD anyway. So for discards, the existing non-CQE approach is
taken, where the mmc core code issues the 3 commands one at a time i.e.
mmc_erase(). Where DCMD is used, is for issuing flushes.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Define and use a blk-mq queue. Discards and flushes are processed
synchronously, but reads and writes asynchronously. In order to support
slow DMA unmapping, DMA unmapping is not done until after the next request
is started. That means the request is not completed until then. If there is
no next request then the completion is done by queued work.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Until mmc has blk-mq support fully implemented and tested, add a parameter
use_blk_mq, set to true if config option MMC_MQ_DEFAULT is selected, which
it is by default.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Add error-handling comments to explain what would also be done for blk-mq
if it used the legacy error-handling.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Make mmc_pre_req() and mmc_post_req() available to the card drivers. Later
patches will make use of this.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Use blk_cleanup_queue() to shutdown the queue when the driver is removed,
and instead get an extra reference to the queue to prevent the queue being
freed before the final mmc_blk_put().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
mmc_cleanup_queue() is not used by a different module. Do not export it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Documentation/timers/timers-howto.txt recommends to use usleep_range for
delays 1-20ms. Let's adhere to it. No need for messing with HZ and still
do busy looping these days.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is not efficient to call gpiod_to_irq() regardless the flag, then
ignore the returned irq if MMC_CAP_NEEDS_POLL.
Move gpiod_to_irq() after the MMC_CAP_NEEDS_POLL check.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the latest version of parsing the new eMMC bindings was moved from
core.c to mmc.c, it was overlooked that drv_type could be used
uninitialized. Fix it!
Fixes: 6186d06c51 ("mmc: parse new binding for eMMC fixed driver type")
Reported-by: Colin Ian King <colin.king@canonical.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Ensure that debugfs files are removed properly
- Fix missing blk_put_request()
- Deal with errors from blk_get_request()
- Rewind mmc bus suspend operations at failures
- Prepend '0x' to ocr and pre_eol_info in sysfs to identify as hex
MMC host:
- sdhci-msm: Make it optional to wait for signal level changes
- sdhci: Avoid swiotlb buffer being full
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJaISyrAAoJEP4mhCVzWIwp84EP/RATcINow1f9vuIT1FJJ9vUl
tAIo52Sx/9MEulLTGrfpbPSy0ZaEuNB+o5aMadXJ1YpQlkDkn760muTWA/widr4C
eriBiBBR6UPI6zTItfgM4JqcrkW6qocEieNTe+mCk968PV0og16hRLMRV8ewlgJO
QXnw5PrwDYRl6ejB3h1K8LDxyKfW1I7cV8GBluwwKc05wTO1vxcjbCyG2zD16zbz
Yj7gbN2ttDMSvo9NpvFZFHBMeWWCvfOtlvU4uF5sxbLOmeF06oEJfQgLQnBWdh+j
wYFuP5CCpzKcaXBMt+AcE8m+Re5oss+eZ7qkojReSh9Mr1iS+41tqjhzEXeD0Ck8
oS/tCsvNRkXuRjaRins7PQ2cDZ29822vv1kgM6RvHDGrSrTvyNc2jitWSFChjb2W
ePue5eQQn7jM/C1ThDAt1uDWjIidovcSTCm4T7pFqV6Fy/090AMhY7HzyNjmTwc9
VkC7umZZt7RWnMS+6hhLLjyX2Oej9XTkLQ6gbiMp2RGpiTvdStqW6ohfUo4xb+9O
48tR24JjqCbbvTHpqX1agO5sL+R9rjGt7DRwLk+C3s6szpaAmuYyCLZXIIHQaQOY
eH9oM8wW9iXK7LQR4tPcuuNjTmM4GOCslPMC0XfPdpcvujJwGRT8pjSI/ajPr7dP
XVdvFhLS3kVMqvJR6rAn
=13VJ
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Ensure that debugfs files are removed properly
- Fix missing blk_put_request()
- Deal with errors from blk_get_request()
- Rewind mmc bus suspend operations at failures
- Prepend '0x' to ocr and pre_eol_info in sysfs to identify as hex
MMC host:
- sdhci-msm: Make it optional to wait for signal level changes
- sdhci: Avoid swiotlb buffer being full"
* tag 'mmc-v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: core: prepend 0x to OCR entry in sysfs
mmc: core: prepend 0x to pre_eol_info entry in sysfs
mmc: sdhci: Avoid swiotlb buffer being full
mmc: sdhci-msm: Optionally wait for signal level changes
mmc: block: Ensure that debugfs files are removed
mmc: core: Do not leave the block driver in a suspended state
mmc: block: Check return value of blk_get_request()
mmc: block: Fix missing blk_put_request()
The sysfs entry "ocr" was missing the 0x prefix to identify it as hex
formatted.
Fixes: 5fb06af7a3 ("mmc: core: Extend sysfs with OCR register")
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Cc: <stable@vger.kernel.org> # v4.8+
[Ulf: Amended change to also cover SD-cards]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sysfs entry "pre_eol_info" was missing the 0x prefix to identify it
as hex formatted.
Fixes: 46bc5c408e ("mmc: core: Export device lifetime information through sysfs")
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The card is not necessarily being removed, but the debugfs files must be
removed when the driver is removed, otherwise they will continue to exist
after unbinding the card from the driver. e.g.
# echo "mmc1:0001" > /sys/bus/mmc/drivers/mmcblk/unbind
# cat /sys/kernel/debug/mmc1/mmc1\:0001/ext_csd
[ 173.634584] BUG: unable to handle kernel NULL pointer dereference at 0000000000000050
[ 173.643356] IP: mmc_ext_csd_open+0x5e/0x170
A complication is that the debugfs_root may have already been removed, so
check for that too.
Fixes: 627c3ccfb4 ("mmc: debugfs: Move block debugfs into block module")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org # 4.14+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The block driver must be resumed if the mmc bus fails to suspend the card.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Introduce host claiming by context to support blkmq
- Preparations for enabling CQE (eMMC CMDQ) requests
- Re-factorizations to prepare for blkmq support
- Re-factorizations to prepare for CQE support
- Fix signal voltage switch for SD cards without power cycle
- Convert RPMB to a character device
- Export eMMC revision via sysfs
- Support eMMC DT binding for fixed driver type
- Document mmc_regulator_get_supply() API
MMC host:
- omap_hsmmc: Updated regulator management for PBIAS
- sdhci-omap: Add new OMAP SDHCI driver
- meson-mx-sdio: New driver for the Amlogic Meson8 and Meson8b SoCs
- sdhci-pci: Add support for Intel CDF
- sdhci-acpi: Fix voltage switch for some Intel host controllers
- sdhci-msm: Enable delay circuit calibration clocks
- sdhci-msm: Manage power IRQ properly
- mediatek: Add support of mt2701/mt2712
- mediatek: Updates management of clocks and tunings
- mediatek: Upgrade eMMC HS400 support
- rtsx_pci: Update tuning for gen3 PCI-Express
- renesas_sdhi: Support R-Car Gen[123] fallback compatibility strings
- Catch all errors when getting regulators
- Various additional improvements and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3Gvx
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Introduce host claiming by context to support blkmq
- Preparations for enabling CQE (eMMC CMDQ) requests
- Re-factorizations to prepare for blkmq support
- Re-factorizations to prepare for CQE support
- Fix signal voltage switch for SD cards without power cycle
- Convert RPMB to a character device
- Export eMMC revision via sysfs
- Support eMMC DT binding for fixed driver type
- Document mmc_regulator_get_supply() API
MMC host:
- omap_hsmmc: Updated regulator management for PBIAS
- sdhci-omap: Add new OMAP SDHCI driver
- meson-mx-sdio: New driver for the Amlogic Meson8 and Meson8b SoCs
- sdhci-pci: Add support for Intel CDF
- sdhci-acpi: Fix voltage switch for some Intel host controllers
- sdhci-msm: Enable delay circuit calibration clocks
- sdhci-msm: Manage power IRQ properly
- mediatek: Add support of mt2701/mt2712
- mediatek: Updates management of clocks and tunings
- mediatek: Upgrade eMMC HS400 support
- rtsx_pci: Update tuning for gen3 PCI-Express
- renesas_sdhi: Support R-Car Gen[123] fallback compatibility strings
- Catch all errors when getting regulators
- Various additional improvements and cleanups"
* tag 'mmc-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (91 commits)
sdhci-fujitsu: add support for setting the CMD_DAT_DELAY attribute
dt-bindings: sdhci-fujitsu: document cmd-dat-delay property
mmc: tmio: Replace msleep() of 20ms or less with usleep_range()
mmc: dw_mmc: Convert timers to use timer_setup()
mmc: dw_mmc: Cleanup the DTO timer like the CTO one
mmc: vub300: Use common code in __download_offload_pseudocode()
mmc: tmio: Use common error handling code in tmio_mmc_host_probe()
mmc: Convert timers to use timer_setup()
mmc: sdhci-acpi: Fix voltage switch for some Intel host controllers
mmc: sdhci-acpi: Let devices define their own private data
mmc: mediatek: perfer to use rise edge latching for cmd line
mmc: mediatek: improve eMMC hs400 mode read performance
mmc: mediatek: add latch-ck support
mmc: mediatek: add support of source_cg clock
mmc: mediatek: add stop_clk fix and enhance_rx support
mmc: mediatek: add busy_check support
mmc: mediatek: add async fifo and data tune support
mmc: mediatek: add pad_tune0 support
mmc: mediatek: make hs400_tune_response only for mt8173
arm64: dts: mt8173: remove "mediatek, mt8135-mmc" from mmc nodes
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Parse the new binding and store it in the host struct after doing some
sanity checks. The code is designed to support fixed SD driver type if
we ever need that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Especially, make clear what the return value means.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some boards have SD card connectors where the power rail cannot be switched
off by the driver. However there are various circumstances when a card
might be re-initialized, such as after system resume, warm re-boot, or
error handling. However, a UHS card will continue to use 1.8V signaling
unless it is power cycled.
If the card has not been power cycled, it may still be using 1.8V
signaling. According to the SD spec., the Bus Speed Mode (function group 1)
bits 2 to 4 are zero if the card is initialized at 3.3V signal level. Thus
they can be used to determine if the card has already switched to 1.8V
signaling. Detect that situation and try to initialize a UHS-I (1.8V)
transfer mode.
Tested with the following cards:
Transcend 4GB High Speed
Kingston 64GB SDR104
Lexar by Micron HIGH-PERFORMANCE 300x 16GB DDR50
SanDisk Ultra 8GB DDR50
Transcend Ultimate 600x 16GB SDR104
Transcend Premium 300x 64GB SDR104
Lexar by Micron Professional 1000x 32GB UHS-II SDR104
SanDisk Extreme Pro 16GB SDR104
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Zhoujie Wu <zjwu@marvell.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out mmc_host_set_uhs_voltage() so it can be reused.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The following functions are needed by the mmc block device driver, once it
converts to blkmq, therefore let's export them.
mmc_start_bkops()
mmc_start_request()
mmc_retune_hold_now()
mmc_retune_release()
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out some common code that will also be used with blk-mq.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enhance mmc_blk_data_prep() to support CQE requests. That means adding
some things that for non-CQE requests would be encoded into the command
arguments - such as the block address, reliable-write flag, and data tag
flag. Also the request tag is needed to provide the command queue task id,
and a comment is added to explain the future possibility of defining a
priority.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use local variables in mmc_blk_data_prep() in preparation for adding CQE
support which doesn't use the output variables.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable or disable CQE when a card is added or removed respectively.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable the Command Queue if the host controller supports a command queue
engine. It is not compatible with Packed Commands, so make a note of that in the
comment.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add core support for handling CQE requests, including starting, completing
and recovering.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently the host can be claimed by a task. Change this so that the host
can be claimed by a context that may or may not be a task. This provides
for the host to be claimed by a block driver queue to support blk-mq, while
maintaining compatibility with the existing use of mmc_claim_host().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Callers already have the host claimed, so remove the unnecessary
calls to mmc_claim_host() and mmc_release_host().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I forgot to account for the fact that the device core holds a
reference to a device added with device_initialize() that need
to be released with a corresponding put_device() to reach a 0
refcount at the end of the lifecycle.
This led to a NULL pointer reference when freeing the device
when e.g. unbidning the host device in sysfs.
Fix this and use the device .release() callback to free the
IDA and free:ing the memory used by the RPMB device.
Before this patch:
/sys/bus/amba/drivers/mmci-pl18x$ echo 80114000.sdi4_per2 > unbind
[ 29.797332] mmc3: card 0001 removed
[ 29.810791] Unable to handle kernel NULL pointer dereference at
virtual address 00000050
[ 29.818878] pgd = de70c000
[ 29.821624] [00000050] *pgd=1e70a831, *pte=00000000, *ppte=00000000
[ 29.827911] Internal error: Oops: 17 [#1] PREEMPT SMP ARM
[ 29.833282] Modules linked in:
[ 29.836334] CPU: 1 PID: 154 Comm: sh Not tainted
4.14.0-rc3-00039-g83318e309566-dirty #736
[ 29.844604] Hardware name: ST-Ericsson Ux5x0 platform (Device Tree Support)
[ 29.851562] task: de572700 task.stack: de742000
[ 29.856079] PC is at kernfs_find_ns+0x8/0x100
[ 29.860443] LR is at kernfs_find_and_get_ns+0x30/0x48
After this patch:
/sys/bus/amba/drivers/mmci-pl18x$ echo 80005000.sdi4_per2 > unbind
[ 20.623382] mmc3: card 0001 removed
Fixes: 97548575be ("mmc: block: Convert RPMB to a character device")
Reported-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This function is used by the block layer queue to bail out of
requests if the current request is towards an RPMB
"block device".
This was done to avoid boot time scanning of this "block
device" which was never really a block device, thus duct-taping
over the fact that it was badly engineered.
This problem is now gone as we removed the offending RPMB block
device in another patch and replaced it with a character
device.
Cc: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The RPMB partition on the eMMC devices is a special area used
for storing cryptographically safe information signed by a
special secret key. To write and read records from this special
area, authentication is needed.
The RPMB area is *only* and *exclusively* accessed using
ioctl():s from userspace. It is not really a block device,
as blocks cannot be read or written from the device, also
the signed chunks that can be stored on the RPMB are actually
256 bytes, not 512 making a block device a real bad fit.
Currently the RPMB partition spawns a separate block device
named /dev/mmcblkNrpmb for each device with an RPMB partition,
including the creation of a block queue with its own kernel
thread and all overhead associated with this. On the Ux500
HREFv60 platform, for example, the two eMMCs means that two
block queues with separate threads are created for no use
whatsoever.
I have concluded that this block device design for RPMB is
actually pretty wrong. The RPMB area should have been designed
to be accessed from /dev/mmcblkN directly, using ioctl()s on
the main block device. It is however way too late to change
that, since userspace expects to open an RPMB device in
/dev/mmcblkNrpmb and we cannot break userspace.
This patch tries to amend the situation using the following
strategy:
- Stop creating a block device for the RPMB partition/area
- Instead create a custom, dynamic character device with
the same name.
- Make this new character device support exactly the same
set of ioctl()s as the old block device.
- Wrap the requests back to the same ioctl() handlers, but
issue them on the block queue of the main partition/area,
i.e. /dev/mmcblkN
We need to create a special "rpmb" bus type in order to get
udev and/or busybox hot/coldplug to instantiate the device
node properly.
Before the patch, this appears in 'ps aux':
101 root 0:00 [mmcqd/2rpmb]
123 root 0:00 [mmcqd/3rpmb]
After applying the patch these surplus block queue threads
are gone, but RPMB is as usable as ever using the userspace
MMC tools, such as 'mmc rpmb read-counter'.
We get instead those dynamice devices in /dev:
brw-rw---- 1 root root 179, 0 Jan 1 2000 mmcblk0
brw-rw---- 1 root root 179, 1 Jan 1 2000 mmcblk0p1
brw-rw---- 1 root root 179, 2 Jan 1 2000 mmcblk0p2
brw-rw---- 1 root root 179, 5 Jan 1 2000 mmcblk0p5
brw-rw---- 1 root root 179, 8 Jan 1 2000 mmcblk2
brw-rw---- 1 root root 179, 16 Jan 1 2000 mmcblk2boot0
brw-rw---- 1 root root 179, 24 Jan 1 2000 mmcblk2boot1
crw-rw---- 1 root root 248, 0 Jan 1 2000 mmcblk2rpmb
brw-rw---- 1 root root 179, 32 Jan 1 2000 mmcblk3
brw-rw---- 1 root root 179, 40 Jan 1 2000 mmcblk3boot0
brw-rw---- 1 root root 179, 48 Jan 1 2000 mmcblk3boot1
brw-rw---- 1 root root 179, 33 Jan 1 2000 mmcblk3p1
crw-rw---- 1 root root 248, 1 Jan 1 2000 mmcblk3rpmb
Notice the (248,0) and (248,1) character devices for RPMB.
Cc: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In may, Steven sent a patch deleting the bounce buffer handling
and the CONFIG_MMC_BLOCK_BOUNCE option.
I chose the less invasive path of making it a runtime config
option, and we merged that successfully for kernel v4.12.
The code is however just standing in the way and taking up
space for seemingly no gain on any systems in wide use today.
Pierre says the code was there to improve speed on TI SDHCI
controllers on certain HP laptops and possibly some Ricoh
controllers as well. Early SDHCI controllers lacked the
scatter-gather feature, which made software bounce buffers
a significant speed boost.
We are clearly talking about the list of SDHCI PCI-based
MMC/SD card readers found in the pci_ids[] list in
drivers/mmc/host/sdhci-pci-core.c.
The TI SDHCI derivative is not supported by the upstream
kernel. This leaves the Ricoh.
What we can however notice is that the x86 defconfigs in the
kernel did not enable CONFIG_MMC_BLOCK_BOUNCE option, which
means that any such laptop would have to have a custom
configured kernel to actually take advantage of this
bounce buffer speed-up. It simply seems like there was
a speed optimization for the Ricoh controllers that noone
was using. (I have not checked the distro defconfigs but
I am pretty sure the situation is the same there.)
Bounce buffers increased performance on the OMAP HSMMC
at one point, and was part of the original submission in
commit a45c6cb816 ("[ARM] 5369/1: omap mmc: Add new
omap hsmmc controller for 2430 and 34xx, v3")
This optimization was removed in
commit 0ccd76d4c2 ("omap_hsmmc: Implement scatter-gather
emulation")
which found that scatter-gather emulation provided even
better performance.
The same was introduced for SDHCI in
commit 2134a922c6 ("sdhci: scatter-gather (ADMA) support")
I am pretty positively convinced that software
scatter-gather emulation will do for any host controller what
the bounce buffers were doing. Essentially, the bounce buffer
was a reimplementation of software scatter-gather-emulation in
the MMC subsystem, and it should be done away with.
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Juha Yrjola <juha.yrjola@solidboot.com>
Cc: Steven J. Hill <Steven.Hill@cavium.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Suggested-by: Steven J. Hill <Steven.Hill@cavium.com>
Suggested-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver strength selection is missed and required when selecting
hs400es. So, It is added here.
Fixes: 81ac2af657 ("mmc: core: implement enhanced strobe support")
Cc: stable@vger.kernel.org
Signed-off-by: Hankyung Yu <hankyung.yu@lge.com>
Signed-off-by: Chanho Min <chanho.min@lge.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_init_request() depends on card->bouncesz so it must be calculated
before blk_init_allocated_queue() starts allocating requests.
Reported-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Fixes: 304419d8a7 ("mmc: core: Allocate per-request data using the..")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Pavel Machek <pavel@ucw.cz>
mmc_start_areq() is an internal mmc core API. Move the declaration
accordingly.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The intention for this patch is to help folks debug the failure
like this:
dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mode.
dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller.
dwmmc_rockchip fe320000.dwmmc: Version ID is 270a
dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 28,32 bit
host data width,256 deep fifo
dwmmc_rockchip fe320000.dwmmc: Got CD GPIO
mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual
400000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz,
actual 50000000HZ div = 0)
mmc0: new high speed SDHC card at address 0007
mmcblk: probe of mmc0:0007 failed with error -28
The reason may be some buggy userspace daemon miss the disk remove
uevent sometimes so it would finally make the SD card not work.
So from the dmesg it only shows a errno of -28 but still don't understand
what happened.
For quick reproduce this, we could set max_devices to 8 and run
for i in $(seq 1 9); do
echo "========================" $i
echo fe320000.dwmmc > /sys/bus/platform/drivers/dwmmc_rockchip/unbind
sleep .5
echo fe320000.dwmmc > /sys/bus/platform/drivers/dwmmc_rockchip/bind
sleep .5
mount -t vfat /dev/mmcblk0 /mnt
sleep .5
done
Another possible reason would be the device has more partitions than
what we support, so that they have to increase their max_devices.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of passing a block device to
mmc_blk_ioctl[_multi]_cmd(), let's pass struct mmc_blk_data()
so we operate ioctl()s on the MMC block device representation
rather than the vanilla block device.
This saves a little duplicated code and makes it possible to
issue ioctl()s not targeted for a specific block device but
rather for a specific partition/area.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of passing a struct mmc_blk_data * to mmc_blk_part_switch()
let's pass the actual partition type we want to switch to. This
is necessary in order not to have a block device with a backing
mmc_blk_data and request queue and all for every hardware partition,
such as RPMB.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_blk_ioctl() calls either mmc_blk_ioctl_cmd() or
mmc_blk_ioctl_multi_cmd() and each of these make the same
check. Factor it into a new helper function, call it on
both branches of the switch() statement and save a chunk
of duplicate code.
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we don't have the block layer enabled, we do not present card
status and extcsd in the debugfs.
Debugfs is not ABI, and maintaining files of no relevance for
non-block devices comes at a high maintenance cost if we shall
support it with the block layer compiled out.
The debugfs entries suffer from all the same starvation
issues as the other userspace things, under e.g. a heavy
dd operation.
The expected number of debugfs users utilizing these two
debugfs files is already low as there is an ioctl() to get the
same information using the mmc-tools, and of these few users
the expected number of people using it on SDIO or combo cards
are expected to be zero.
It is therefore logical to move this over to the block layer
when it is enabled, using the new custom requests and issue
it using the block request queue.
On the other hand it moves some debugfs code from debugfs.c
and into block.c.
Tested during heavy dd load by cat:in the status file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This function retrieves the status of the card with the default
number of retries. Since the block layer wants to use this, and
since the block layer is a loadable kernel module, we need to
export this symbol.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We have a data pointer for the ioctl() data, but we need to
pass other data along with the DRV_OP:s, so make this a
void * so it can be reused.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The new lockdep annotations for completions cause a warning in the
mmc test module, in a function that now has four 150 byte structures
on the stack:
drivers/mmc/core/mmc_test.c: In function 'mmc_test_nonblock_transfer.constprop':
drivers/mmc/core/mmc_test.c:892:1: error: the frame size of 1360 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
The mmc_test_ongoing_transfer function evidently had a similar problem,
and worked around it by using dynamic allocation.
This generalizes the approach used by mmc_test_ongoing_transfer() and
applies it to mmc_test_nonblock_transfer() as well.
Fixes: cd8084f91c ("locking/lockdep: Apply crossrelease to completions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CQE needs to be off for the host controller to accept non-CQ commands. Turn
off the CQE before sending commands, and ensure it is off in any reset or
power management paths, or re-tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_return_hold() / mmc_retune_release() are used around a group of
commands to prevent re-tuning between the commands. Re-tuning can still
happen before the first command. In some cases, re-tuning must be
prevented entirely. Add mmc_retune_hold_now() for that purpose. It is
added in preparation for CQE support where it will be used by CQE recovery.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Packed commands support was removed but some bits got left behind. Remove
them.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per the SD physical layer simplified specification V4.10,
section 4.6.2, CSD version 1.0 SD card should use taac, nsac
and r2w_factor for calculating the data access time. But the
taac and nsac for SDHC(CSD version 2.0) are always fixed and
the software should use the recommended value for timeout. When
parsing the CSD, we sanely set them to zero for SDHC(CSD version
2.0), all the calculation for timeout_ns and timeout_clk is zero
as well. So what we actually want to limit here is either SDHC
case or unreasonable timeout reported by the cards. In principle
we should at least be able to remove the bogus check for the
mmc_card_blockaddr.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per the spec of JESD84-B51, section 7.3, replace tacc with taac to
fix the obvious typo.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Jan Glauber <jglauber@cavium.com>
Cc: David Daney <david.daney@cavium.com>
Cc: "Steven J. Hill" <Steven.Hill@cavium.com>
Cc: linux-mmc@vger.kernel.org
Acked-by: David Daney <david.daney@cavium.com>
Tested-by: Steven J. Hill <Steven.Hill@cavium.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are lots of debug message in core.c which use pr_debug
for better dynamic log level control. So it doesn't make sense
for those print to still keep working only under CONFIG_MMC_DEBUG.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All the check within mmc_mrq_prep seems to be all-or-none
proposition, so it doesn't make sense to only check the
length of sglist only under the CONFIG_MMC_DEBUG context.
I'd prefer to always keep the check there unconditionally.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The intention of this check was to prevent the conflict between
hotplug and removing driver for whatever reason. Currently it
doesn't improve anything and the following rescan process could
still saftly perform the scan flow. So these code seems pointless
now and let's remove them.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It was never used and introduced a long standing compile
warning:
drivers/mmc/core/block.c: In function 'power_ro_lock_store':
drivers/mmc/core/block.c:191:19: warning: variable 'card' set but not
used [-Wunused-but-set-variable]
Remove it to fix the warning.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Just a trivial fix for that found by reading the code.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 2a842acab1 ("block: introduce new block status code type") changed
the error type but not in patches merged through the mmc tree, like
commit 0493f6fe5b ("mmc: block: Move boot partition locking into a driver
op"). Fix one error code that is incorrect and also use BLK_STS_OK in
preference to 0.
Fixes: 17ece345a0 ("Merge tag 'mmc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We to some extent should tolerate R1_OUT_OF_RANGE for open-ending
mode as it is expected behaviour and most of the backup partition
tables should be located near some of the last blocks which will
always make open-ending read exceed the capacity of cards.
Fixes: 9820a5b111 ("mmc: core: for data errors, take response of stop cmd into account")
Fixes: a04e6bae9e ("mmc: core: check also R1 response for stop commands")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change the default err value to -EINVAL, make sure the card only
has type EXT_CSD_CARD_TYPE_HS400_1_8V also do the signal voltage
setting when select hs400es mode.
Fixes: commit 1720d3545b ("mmc: core: switch to 1V8 or 1V2 for hs400es mode")
Cc: <stable@vger.kernel.org>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 304419d8a7 ("mmc: core: Allocate per-request data using the
block layer core") refactored mechanism of queue handling caused
mmc_init_request() can be called just after mmc_cleanup_queue() caused null
pointer dereference.
Another commit bbdc74dc19 ("mmc: block: Prevent new req entering queue
after its cleanup") tried to fix the problem. However it actually miss one
corner case.
We could still reproduce the issue mentioned with these steps:
(1) insert a SD card and mount it
(2) hotplug it, so it will leave md->usage still be counted
(3) reboot the system which will sync data and umount the card
[Unable to handle kernel NULL pointer dereference at virtual address
00000000
[user pgtable: 4k pages, 48-bit VAs, pgd = ffff80007bab3000
[[0000000000000000] *pgd=000000007a828003, *pud=0000000078dce003,
*pmd=000000007aab6003, *pte=0000000000000000
[Internal error: Oops: 96000007 [#1] PREEMPT SMP
[Modules linked in:
[CPU: 3 PID: 3507 Comm: umount Tainted: G W
4.13.0-rc1-next-20170720-00012-g9d9bf45 #33
[Hardware name: Firefly-RK3399 Board (DT)
[task: ffff80007a1de200 task.stack: ffff80007a01c000
[PC is at mmc_init_request+0x14/0xc4
[LR is at alloc_request_size+0x4c/0x74
[pc : [<ffff0000087d7150>] lr : [<ffff000008378fe0>] pstate: 600001c5
[sp : ffff80007a01f8f0
....
[[<ffff0000087d7150>] mmc_init_request+0x14/0xc4
[[<ffff000008378fe0>] alloc_request_size+0x4c/0x74
[[<ffff00000817ac28>] mempool_create_node+0xb8/0x17c
[[<ffff00000837aadc>] blk_init_rl+0x9c/0x120
[[<ffff000008396580>] blkg_alloc+0x110/0x234
[[<ffff000008396ac8>] blkg_create+0x424/0x468
[[<ffff00000839877c>] blkg_lookup_create+0xd8/0x14c
[[<ffff0000083796bc>] generic_make_request_checks+0x368/0x3b0
[[<ffff00000837b050>] generic_make_request+0x1c/0x240
So mmc_blk_put wouldn't calling blk_cleanup_queue which actually the
QUEUE_FLAG_DYING and QUEUE_FLAG_BYPASS should stay. Block core expect
blk_queue_bypass_{start, end} internally to bypass/drain the queue before
actually dying the queue, so it didn't expose API to set the queue bypass.
I think we should set QUEUE_FLAG_BYPASS whenever queue is removed, although
the md->usage is still counted, as no dispatch queue could be found then.
Fixes: 304419d8a7 ("mmc: core: Allocate per-request data using the block layer core")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With gcc 4.1.2:
drivers/mmc/core/block.c: In function ‘mmc_blk_ioctl_cmd_issue’:
drivers/mmc/core/block.c:630: warning: ‘ioc_err’ may be used uninitialized in this function
Indeed, if mq_rq->ioc_count is zero, an uninitialized value will be
stored in mq_rq->drv_op_result and passed to blk_end_request_all().
Can mq_rq->ioc_count be zero?
- mmc_blk_ioctl_cmd() sets ioc_count to 1, so this is safe,
- mmc_blk_ioctl_multi_cmd() obtains ioc_count from user space in
response to the MMC_IOC_MULTI_CMD ioctl, and does allow zero.
To avoid returning an uninitialized value, and as it is pointless to do
all this work when the MMC_IOC_MULTI_CMD ioctl is used with zero
entries, check for this early in mmc_blk_ioctl_multi_cmd(), and return
zero, like was returned before.
Fixes: 3ecd8cf23f ("mmc: block: move multi-ioctl() to use block layer")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With gcc 4.1.2:
drivers/mmc/core/block.c: In function ‘mmc_blk_issue_drv_op’:
drivers/mmc/core/block.c:1178: warning: ‘ret’ may be used uninitialized in this function
Indeed, for MMC_DRV_OP_IOCTL, if mq_rq->ioc_count is zero, an
uninitialized value will be stored in mq_rq->drv_op_result and passed to
blk_end_request_all().
Can mq_rq->ioc_count be zero?
- mmc_blk_ioctl_cmd() sets ioc_count to 1, so this is safe,
- mmc_blk_ioctl_multi_cmd() obtains ioc_count from user space in
response to the MMC_IOC_MULTI_CMD ioctl, and does allow zero.
Initialize ret to zero to fix this for current and future callers.
Fixes: 0493f6fe5b ("mmc: block: Move boot partition locking into a driver op")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Add support to enable irq wake for slot gpio
- Remove MMC_CAP2_HC_ERASE_SZ and make it the default behaviour
- Improve R1 response error checks for stop commands
- Cleanup and clarify some MMC specific code
- Keep card runtime resumed while adding SDIO function devices
- Use device_property_read instead of of_property_read in mmc_of_parse()
- Move boot partition locking into a driver op to enable proper I/O scheduling
- Move multi/single-ioctl() to use block layer to enable proper I/O scheduling
- Delete bounce buffer Kconfig option
- Improve the eMMC HW reset support provided via the eMMC pwrseq
- Add host API to manage SDIO IRQs from a workqueue
MMC host:
- dw_mmc: Drop support for multiple slots
- dw_mmc: Use device_property_read instead of of_property_read
- dw_mmc-rockchip: Optional improved tuning to greatly decrease tuning time
- dw_mmc: Prevent rpm suspend for SDIO IRQs instead of always for SDIO cards
- dw_mmc: Convert to use MMC_CAP2_SDIO_IRQ_NOTHREAD for SDIO IRQs
- omap_hsmmc: Convert to mmc regulator APIs to consolidate code
- omap_hsmmc: Deprecate "vmmc_aux" in DT and use "vqmmc" instead
- tmio: make sure SDIO gets reinitialized after resume
- sdhi: add CMD23 support to R-Car Gen2 & Gen3
- tmio: add CMD23 support
- sdhi/tmio: Refactor code and rename files to simplify Kconfig options
- sdhci-pci: Enable card detect wake for Intel BYT-related SD controllers
- sdhci-pci: Add support for Intel CNP
- sdhci-esdhc-imx: Remove ENGcm07207 workaround - allow multi block transfers
- sdhci-esdhc-imx: Allow all supported prescaler values
- sdhci-esdhc-imx: Fix DAT line software reset
- sdhci-esdhc: Add SDHCI_QUIRK_32BIT_DMA_ADDR
- atmel-mci: Drop AVR32 support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zJi3
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add support to enable irq wake for slot gpio
- Remove MMC_CAP2_HC_ERASE_SZ and make it the default behaviour
- Improve R1 response error checks for stop commands
- Cleanup and clarify some MMC specific code
- Keep card runtime resumed while adding SDIO function devices
- Use device_property_read instead of of_property_read in mmc_of_parse()
- Move boot partition locking into a driver op to enable proper I/O scheduling
- Move multi/single-ioctl() to use block layer to enable proper I/O scheduling
- Delete bounce buffer Kconfig option
- Improve the eMMC HW reset support provided via the eMMC pwrseq
- Add host API to manage SDIO IRQs from a workqueue
MMC host:
- dw_mmc: Drop support for multiple slots
- dw_mmc: Use device_property_read instead of of_property_read
- dw_mmc-rockchip: Optional improved tuning to greatly decrease tuning time
- dw_mmc: Prevent rpm suspend for SDIO IRQs instead of always for SDIO cards
- dw_mmc: Convert to use MMC_CAP2_SDIO_IRQ_NOTHREAD for SDIO IRQs
- omap_hsmmc: Convert to mmc regulator APIs to consolidate code
- omap_hsmmc: Deprecate "vmmc_aux" in DT and use "vqmmc" instead
- tmio: make sure SDIO gets reinitialized after resume
- sdhi: add CMD23 support to R-Car Gen2 & Gen3
- tmio: add CMD23 support
- sdhi/tmio: Refactor code and rename files to simplify Kconfig options
- sdhci-pci: Enable card detect wake for Intel BYT-related SD controllers
- sdhci-pci: Add support for Intel CNP
- sdhci-esdhc-imx: Remove ENGcm07207 workaround - allow multi block transfers
- sdhci-esdhc-imx: Allow all supported prescaler values
- sdhci-esdhc-imx: Fix DAT line software reset
- sdhci-esdhc: Add SDHCI_QUIRK_32BIT_DMA_ADDR
- atmel-mci: Drop AVR32 support"
* tag 'mmc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (86 commits)
mmc: dw_mmc: remove the unnecessary slot variable
mmc: dw_mmc: use the 'slot' instead of 'cur_slot'
mmc: dw_mmc: remove the 'id' arguments about functions relevant to slot
mmc: dw_mmc: change the array of slots
mmc: dw_mmc: remove the loop about finding slots
mmc: dw_mmc: deprecated the "num-slots" property
mmc: dw_mmc-rockchip: parse rockchip, desired-num-phases from DT
dt-bindings: rockchip-dw-mshc: add optional rockchip, desired-num-phases
mmc: renesas-sdhi: improve checkpatch cleanness
mmc: tmio: improve checkpatch cleanness
mmc: sdhci-pci: Enable card detect wake for Intel BYT-related SD controllers
mmc: slot-gpio: Add support to enable irq wake on cd_irq
mmc: core: Remove MMC_CAP2_HC_ERASE_SZ
mmc: core: for data errors, take response of stop cmd into account
mmc: core: check also R1 response for stop commands
mmc: core: Clarify code for sending CSD
mmc: core: Drop mmc_all_send_cid() and use mmc_send_cxd_native() instead
mmc: core: Re-factor code for sending CID
mmc: core: Remove redundant code in mmc_send_cid()
mmc: core: Make mmc_can_reset() static
...
BLK_BOUNCE_ANY is the defauly now, so the call is superflous.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add host capability MMC_CAP_CD_WAKE to enable irq wake on the card detect
irq.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC_CAP2_HC_ERASE_SZ is used only by a few mmc host drivers. Its intent
is to enable eMMC's high-capacity erase size, as to improve the behaviour
of the erase operations.
We should strive to avoid software configuration options that aren't
necessary, but instead deploy common behaviours. For these reasons, let's
remove the capability bit for MMC_CAP2_HC_ERASE_SZ and make it the default
behaviour.
Note that this change doesn't affect eMMCs supporting trim/discard, because
these commands operates on sectors and takes precedence over erase
commands.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Some errors are flagged only with the next command after a multiblock
transfer, e.g. ECC error. So, when checking for data transfer errors,
we check the result from the stop command as well.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To detect errors like ECC errors, we must parse the R1 response bits. Introduce
a helper function to also set the error value of a command when R1 error bits
are set. Add ECC error to list of flags checked. Use the new helper for the
stop command to call mmc_blk_recovery when detecting ECC errors which are only
flagged on the next command after multiblock.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To make the code more consistent and to increase readability, add an
mmc_spi_send_csd() function, which gets called from mmc_send_csd() in case
of SPI mode.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Instead of having the caller to check for SPI mode, let's leave that to
internals of mmc_send_cid(). In this way the code gets cleaner and it
becomes clear what is specific to SPI and non-SPI mode.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_send_cid() is never called using non SPI mode. Thus, let's remove
the redundant code dealing with this.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_flush_cache() is a eMMC specific function, let's move it to
mmc_ops.c to make that clear.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_interrupt_hpi() is a eMMC specific function, let's move it to
mmc_ops.c to make that clear. The move also enables us to make
mmc_send_hpi_cmd() static, so let's do that change as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_start_bkops(), mmc_stop_bkops() and mmc_read_bkops_status()
functions are all specific to eMMCs. To make this clear, let's move them
from from core.c to mmc_ops.c and take the opportunity to make
mmc_read_bkops_status() static.
While moving them, get rid of MMC_BKOPS_MAX_TIMEOUT (4 min) and use the
common default timeout MMC_OPS_TIMEOUT_MS (10 min) instead, as there is no
need to have specific default timeout for bkops.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_start|stop_bkops(), mmc_read_bkops_status() and mmc_interrupt_hpi()
functions are all used from within the mmc core module, thus there are no
need to use EXPORT_SYMBOL() for them, so let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Drivers core will runtime suspend a device with no driver. That means the
SDIO card will be runtime suspended as soon as it is added. It is then
runtime resumed to add each function. That is entirely pointless, so add
pm runtime get/put to keep the SDIO card runtime resumed until the function
devices have been added.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The error path deletes the device by calling mmc_sdio_remove() which must
be called without the host claimed. Simplify the error path so it does just
that and add a comment about why we don't disable runtime PM.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using the device_property interfaces allows mmc drivers to work
on platforms which run on either device tree or ACPI.
Signed-off-by: David Woods <dwoods@mellanox.com>
Reviewed-by: Chris Metcalf <cmetcalf@mellanox.com>
Cc: stable@vger.linux.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The only reason to why the mmc block device driver needs to implements its
own version of how to get the status of the card, is that it needs to
specify a different amount of retries.
Therefore add a new exported function which allows the caller to specify
the number of retries and convert everybody to use it, as this simplifies
the code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
This moves the boot partition lock command (issued from sysfs)
into a custom block layer request, just like the ioctl()s,
getting rid of yet another instance of mmc_get_card().
Since we now have two operations issuing special DRV_OP's, we
rename the result variable ->drv_op_result.
Tested by locking the boot partition from userspace:
> cd /sys/devices/platform/soc/80114000.sdi4_per2/mmc_host/mmc3/
mmc3:0001/block/mmcblk3/mmcblk3boot0
> echo 1 > ro_lock_until_next_power_on
[ 178.645324] mmcblk3boot1: Locking boot partition ro until next power on
[ 178.652221] mmcblk3boot0: Locking boot partition ro until next power on
Also tested this with a huge dd job in the background: it
is now possible to lock the boot partitions on the card even
under heavy I/O.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We will need to access static functions above the pure block layer
operations in the file, so move the driver operations issue
function down so we can see all non-blocklayer symbols.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We will expand the DRV_OP usage, so we need to know which
operation we're performing. Tag the operations with an
enum:ed type and rename the function so it is clear that
it deals with any command and put a switch statement in
it. Currently only ioctls are supported.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Just as we can use blk_mq_rq_from_pdu() to get the per-request
tag we can use blk_mq_rq_to_pdu() to get a request from a tag.
Introduce a static inline helper so we are on the clear what
is happening.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit cdf8a6fb48
"mmc: block: Introduce queue semantics"
deleted the last user of mmc_req_is_special() and it was
a horrible hack to classify requests as "special" or
"not special" to begin with, so delete the helper.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This switches also the multiple-command ioctl() call to issue
all ioctl()s through the block layer instead of going directly
to the device.
We extend the passed argument with an argument count and loop
over all passed commands in the ioctl() issue function called
from the block layer.
By doing this we are again loosening the grip on the big host
lock, since two calls to mmc_get_card()/mmc_put_card() are
removed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Avri Altman <Avri.Altman@sandisk.com>
This wraps single ioctl() commands into block requests using
the custom block layer request types REQ_OP_DRV_IN and
REQ_OP_DRV_OUT.
By doing this we are loosening the grip on the big host lock,
since two calls to mmc_get_card()/mmc_put_card() are removed.
We are storing the ioctl() in/out argument as a pointer in
the per-request struct mmc_blk_request container. Since we
now let the block layer allocate this data, blk_get_request()
will allocate it for us and we can immediately dereference
it and use it to pass the argument into the block layer.
We refactor the if/else/if/else ladder in mmc_blk_issue_rq()
as part of the job, keeping some extra attention to the
case when a NULL req is passed into this function and
making that pipeline flush more explicit.
Tested on the ux500 with the userspace:
mmc extcsd read /dev/mmcblk3
resulting in a successful EXTCSD info dump back to the
console.
This commit fixes a starvation issue in the MMC/SD stack
that can be easily provoked in the following way by
issueing the following commands in sequence:
> dd if=/dev/mmcblk3 of=/dev/null bs=1M &
> mmc extcs read /dev/mmcblk3
Before this patch, the extcsd read command would hang
(starve) while waiting for the dd command to finish since
the block layer was holding the card/host lock.
After this patch, the extcsd ioctl() command is nicely
interpersed with the rest of the block commands and we
can issue a bunch of ioctl()s from userspace while there
is some busy block IO going on without any problems.
Conversely userspace ioctl()s can no longer starve
the block layer by holding the card/host lock.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Avri Altman <Avri.Altman@sandisk.com>
The variable is_rpmb is clearly a bool and even assigned true
and false, yet declared as an int.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_queue_req is a per-request state container the MMC core uses
to carry bounce buffers, pointers to asynchronous requests and so on.
Currently allocated as a static array of objects, then as a request
comes in, a mmc_queue_req is assigned to it, and used during the
lifetime of the request.
This is backwards compared to how other block layer drivers work:
they usally let the block core provide a per-request struct that get
allocated right beind the struct request, and which can be obtained
using the blk_mq_rq_to_pdu() helper. (The _mq_ infix in this function
name is misleading: it is used by both the old and the MQ block
layer.)
The per-request struct gets allocated to the size stored in the queue
variable .cmd_size initialized using the .init_rq_fn() and
cleaned up using .exit_rq_fn().
The block layer code makes the MMC core rely on this mechanism to
allocate the per-request mmc_queue_req state container.
Doing this make a lot of complicated queue handling go away. We only
need to keep the .qnct that keeps count of how many request are
currently being processed by the MMC layer. The MQ block layer will
replace also this once we transition to it.
Doing this refactoring is necessary to move the ioctl() operations
into custom block layer requests tagged with REQ_OP_DRV_[IN|OUT]
instead of the custom code using the BigMMCHostLock that we have
today: those require that per-request data be obtainable easily from
a request after creating a custom request with e.g.:
struct request *rq = blk_get_request(q, REQ_OP_DRV_IN, __GFP_RECLAIM);
struct mmc_queue_req *mq_rq = req_to_mq_rq(rq);
And this is not possible with the current construction, as the request
is not immediately assigned the per-request state container, but
instead it gets assigned when the request finally enters the MMC
queue, which is way too late for custom requests.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[Ulf: Folded in the fix to drop a call to blk_cleanup_queue()]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Heiner Kallweit <hkallweit1@gmail.com>
This option is activated by all multiplatform configs and what
not so we almost always have it turned on, and the memory it
saves is negligible, even more so moving forward. The actual
bounce buffer only gets allocated only when used, the only
thing the ifdefs are saving is a little bit of code.
It is highly improper to have this as a Kconfig option that
get turned on by Kconfig, make this a pure runtime-thing and
let the host decide whether we use bounce buffers. We add a
new property "disable_bounce" to the host struct.
Notice that mmc_queue_calc_bouncesz() already disables the
bounce buffers if host->max_segs != 1, so any arch that has a
maximum number of segments higher than 1 will have bounce
buffers disabled.
The option CONFIG_MMC_BLOCK_BOUNCE is default y so the
majority of platforms in the kernel already have it on, and
it then gets turned off at runtime since most of these have
a host->max_segs > 1. The few exceptions that have
host->max_segs == 1 and still turn off the bounce buffering
are those that disable it in their defconfig.
Those are the following:
arch/arm/configs/colibri_pxa300_defconfig
arch/arm/configs/zeus_defconfig
- Uses MMC_PXA, drivers/mmc/host/pxamci.c
- Sets host->max_segs = NR_SG, which is 1
- This needs its bounce buffer deactivated so we set
host->disable_bounce to true in the host driver
arch/arm/configs/davinci_all_defconfig
- Uses MMC_DAVINCI, drivers/mmc/host/davinci_mmc.c
- This driver sets host->max_segs to MAX_NR_SG, which is 16
- That means this driver anyways disabled bounce buffers
- No special action needed for this platform
arch/arm/configs/lpc32xx_defconfig
arch/arm/configs/nhk8815_defconfig
arch/arm/configs/u300_defconfig
- Uses MMC_ARMMMCI, drivers/mmc/host/mmci.[c|h]
- This driver by default sets host->max_segs to NR_SG,
which is 128, unless a DMA engine is used, and in that case
the number of segments are also > 1
- That means this driver already disables bounce buffers
- No special action needed for these platforms
arch/arm/configs/sama5_defconfig
- Uses MMC_SDHCI, MMC_SDHCI_PLTFM, MMC_SDHCI_OF_AT91, MMC_ATMELMCI
- Uses drivers/mmc/host/sdhci.c
- Normally sets host->max_segs to SDHCI_MAX_SEGS which is 128 and
thus disables bounce buffers
- Sets host->max_segs to 1 if SDHCI_USE_SDMA is set
- SDHCI_USE_SDMA is only set by SDHCI on PCI adapers
- That means that for this platform bounce buffers are already
disabled at runtime
- No special action needed for this platform
arch/blackfin/configs/CM-BF533_defconfig
arch/blackfin/configs/CM-BF537E_defconfig
- Uses MMC_SPI (a simple MMC card connected on SPI pins)
- Uses drivers/mmc/host/mmc_spi.c
- Sets host->max_segs to MMC_SPI_BLOCKSATONCE which is 128
- That means this platform already disables bounce buffers at
runtime
- No special action needed for these platforms
arch/mips/configs/cavium_octeon_defconfig
- Uses MMC_CAVIUM_OCTEON, drivers/mmc/host/cavium.c
- Sets host->max_segs to 16 or 1
- Setting host->disable_bounce to be sure for the 1 case
arch/mips/configs/qi_lb60_defconfig
- Uses MMC_JZ4740, drivers/mmc/host/jz4740_mmc.c
- This sets host->max_segs to 128 so bounce buffers are
already runtime disabled
- No action needed for this platform
It would be interesting to come up with a list of the platforms
that actually end up using bounce buffers. I have not been
able to infer such a list, but it occurs when
host->max_segs == 1 and the bounce buffering is not explicitly
disabled.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For hosts not supporting MMC_CAP2_SDIO_IRQ_NOTHREAD but MMC_CAP_SDIO_IRQ,
the SDIO IRQs are processed from a dedicated kernel thread. For these
cases, the host calls mmc_signal_sdio_irq() from its ISR to signal a new
SDIO IRQ.
Signaling an SDIO IRQ makes the host's ->enable_sdio_irq() callback to be
invoked to temporary disable the IRQs, before the kernel thread is woken up
to process it. When processing of the IRQs are completed, they are
re-enabled by the kernel thread, again via invoking the host's
->enable_sdio_irq().
The observation from this, is that the execution path is being unnecessary
complex, as the host driver already knows that it needs to temporary
disable the IRQs before signaling a new one. Moreover, replacing the kernel
thread with a work/workqueue would not only greatly simplify the code, but
also make it more robust.
To address the above problems, let's continue to build upon the support for
MMC_CAP2_SDIO_IRQ_NOTHREAD, as it already implements SDIO IRQs to be
processed without using the clumsy kernel thread and without the ping-pong
calls of the host's ->enable_sdio_irq() callback for each processed IRQ.
Therefore, let's add new API sdio_signal_irq(), which enables hosts to
signal/process SDIO IRQs by using a work/workqueue, rather than using the
kernel thread.
Add also a new host callback ->ack_sdio_irq(), which the work invokes when
the SDIO IRQs have been processed. This informs the host about when it
shall re-enable the SDIO IRQs. Potentially, we could re-use the existing
->enable_sdio_irq() callback instead of adding a new one, however it has
turned out that it's more convenient for hosts to get this information via
a separate callback.
Hosts that wants to use this new method to signal/process SDIO IRQs, must
enable MMC_CAP2_SDIO_IRQ_NOTHREAD and implement the ->ack_sdio_irq()
callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
In cases when MMC_CAP2_SDIO_IRQ_NOTHREAD is set, there is a minor window
for when the mmc host could call sdio_run_irqs(), while in fact an SDIO
func driver could have decided to released the SDIO IRQ via a call to
sdio_release_irq(). In this scenario, processing of the SDIO IRQs are done
even if there is none IRQ claimed, which is not what we want.
To prevent this from happen, close the window by validating that at least
one SDIO IRQs is claimed, before deciding to process them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
In case if a pwrseq-emmc has been bound to the host, a call to
mmc_power_up() triggers an eMMC HW reset via the pwrseq_emmc's
->post_power_on() callback. This isn't really what we want, as
mmc_power_up() is called each time when resuming the card.
As a matter of fact, the current approach may also violate the eMMC spec,
as the involved delays managed in pwrseq_emmc assumes both VCC and VCCQ has
been turned on, which isn't the case for VCCQ, unless the regulator is
always on.
Fix this behaviour by aligning to the same procedure used when the mmc host
implements the ->hw_reset() callback and has the MMC_CAP_HW_RESET flag set.
In this way the eMMC HW reset is issued at card detection scan, to cope
with bogus bootloaders and in the error recovery path via the mmc specific
bus_ops->reset() callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
The ->reset() callback is needed to implement a better support for eMMC HW
reset. The following changes will take advantage of the new callback.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Currently we use nornal Linux errno values in the block layer, and while
we accept any error a few have overloaded magic meanings. This patch
instead introduces a new blk_status_t value that holds block layer specific
status codes and explicitly explains their meaning. Helpers to convert from
and to the previous special meanings are provided for now, but I suspect
we want to get rid of them in the long run - those drivers that have a
errno input (e.g. networking) usually get errnos that don't know about
the special block layer overloads, and similarly returning them to userspace
will usually return somethings that strictly speaking isn't correct
for file system operations, but that's left as an exercise for later.
For now the set of errors is a very limited set that closely corresponds
to the previous overloaded errno values, but there is some low hanging
fruite to improve it.
blk_status_t (ab)uses the sparse __bitwise annotations to allow for sparse
typechecking, so that we can easily catch places passing the wrong values.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
If the optional power-off-delay-us property is found, insert the
corresponding delay after asserting the GPIO during power off. This enables
a graceful shutdown sequence for some devices.
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
- Continue to re-factor code to prepare for eMMC CMDQ and blkmq support
- Introduce queue semantics to prepare for eMMC CMDQ and blkmq support
- Add helper functions to manage temporary enable/disable of eMMC CMDQ
- Improve wait-busy detection for SDIO
MMC host:
- cavium: Add driver to support Cavium controllers
- cavium: Extend Cavium driver to support Octeon SOCs and ThunderX SOCs
- bcm2835: Add new driver for Broadcom BCM2835 controller
- sdhci-xenon: Add driver to support Marvell Xenon SDHCI controller
- sdhci-tegra: Add support for the Tegra186 variant
- sdhci-of-esdhc: Support for UHS-I SD cards
- sdhci-of-esdhc: Support for eMMC HS200 cards
- sdhci-cadence: Add eMMC HS400 enhanced strobe support
- sdhci-esdhc-imx: Reset tuning circuit when needed
- sdhci-pci: Modernize and clean-up some PM related code
- sdhci-pci: Avoid re-tuning at runtime PM for some Intel devices
- sdhci-pci|acpi: Use aggressive PM for some Intel BYT controllers
- sdhci: Re-factoring and modernizations
- sdhci: Optimize delay loops
- sdhci: Improve register dump print format
- sdhci: Add support for the Command Queue Engine
- meson-gx: Various improvements and clean-ups
- meson-gx: Add support for CMD23
- meson-gx: Basic tuning support to avoid CRC errors
- s3cmci: Enable probing via DT
- mediatek: Improve tuning support for eMMC HS200 and HS400 mode
- tmio: Improve DMA support
- tmio: Use correct response for CMD12
- dw_mmc: Minor improvements and clean-ups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=p+Hb
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Continue to re-factor code to prepare for eMMC CMDQ and blkmq support
- Introduce queue semantics to prepare for eMMC CMDQ and blkmq support
- Add helper functions to manage temporary enable/disable of eMMC CMDQ
- Improve wait-busy detection for SDIO
MMC host:
- cavium: Add driver to support Cavium controllers
- cavium: Extend Cavium driver to support Octeon and ThunderX SOCs
- bcm2835: Add new driver for Broadcom BCM2835 controller
- sdhci-xenon: Add driver to support Marvell Xenon SDHCI controller
- sdhci-tegra: Add support for the Tegra186 variant
- sdhci-of-esdhc: Support for UHS-I SD cards
- sdhci-of-esdhc: Support for eMMC HS200 cards
- sdhci-cadence: Add eMMC HS400 enhanced strobe support
- sdhci-esdhc-imx: Reset tuning circuit when needed
- sdhci-pci: Modernize and clean-up some PM related code
- sdhci-pci: Avoid re-tuning at runtime PM for some Intel devices
- sdhci-pci|acpi: Use aggressive PM for some Intel BYT controllers
- sdhci: Re-factoring and modernizations
- sdhci: Optimize delay loops
- sdhci: Improve register dump print format
- sdhci: Add support for the Command Queue Engine
- meson-gx: Various improvements and clean-ups
- meson-gx: Add support for CMD23
- meson-gx: Basic tuning support to avoid CRC errors
- s3cmci: Enable probing via DT
- mediatek: Improve tuning support for eMMC HS200 and HS400 mode
- tmio: Improve DMA support
- tmio: Use correct response for CMD12
- dw_mmc: Minor improvements and clean-ups"
* tag 'mmc-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (148 commits)
mmc: sdhci-of-esdhc: limit SD clock for ls1012a/ls1046a
mmc: sdhci-of-esdhc: poll ESDHC_CLOCK_STABLE bit with udelay
mmc: sdhci-xenon: Fix default value of LOGIC_TIMING_ADJUST for eMMC5.0 PHY
mmc: sdhci-xenon: Fix the work flow in xenon_remove().
MIPS: Octeon: cavium_octeon_defconfig: Enable Octeon MMC
mmc: sdhci-xenon: Remove redundant dev_err call in get_dt_pad_ctrl_data()
mmc: cavium: Use module_pci_driver to simplify the code
mmc: cavium: Add MMC support for Octeon SOCs.
mmc: cavium: Fix detection of block or byte addressing.
mmc: core: Export API to allow hosts to get the card address
mmc: sdio: Fix sdio wait busy implement limitation
mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card
clk: apn806: fix spelling mistake: "mising" -> "missing"
mmc: sdhci-of-esdhc: add delay between tuning cycles
mmc: sdhci: Control the delay between tuning commands
mmc: sdhci-of-esdhc: add tuning support
mmc: sdhci-of-esdhc: add support for signal voltage switch
mmc: sdhci-of-esdhc: add peripheral clock support
mmc: sdhci-pci: Allow for 3 bytes from Intel DSM
mmc: cavium: Fix a shift wrapping bug
...
Pull block layer updates from Jens Axboe:
- Add BFQ IO scheduler under the new blk-mq scheduling framework. BFQ
was initially a fork of CFQ, but subsequently changed to implement
fairness based on B-WF2Q+, a modified variant of WF2Q. BFQ is meant
to be used on desktop type single drives, providing good fairness.
From Paolo.
- Add Kyber IO scheduler. This is a full multiqueue aware scheduler,
using a scalable token based algorithm that throttles IO based on
live completion IO stats, similary to blk-wbt. From Omar.
- A series from Jan, moving users to separately allocated backing
devices. This continues the work of separating backing device life
times, solving various problems with hot removal.
- A series of updates for lightnvm, mostly from Javier. Includes a
'pblk' target that exposes an open channel SSD as a physical block
device.
- A series of fixes and improvements for nbd from Josef.
- A series from Omar, removing queue sharing between devices on mostly
legacy drivers. This helps us clean up other bits, if we know that a
queue only has a single device backing. This has been overdue for
more than a decade.
- Fixes for the blk-stats, and improvements to unify the stats and user
windows. This both improves blk-wbt, and enables other users to
register a need to receive IO stats for a device. From Omar.
- blk-throttle improvements from Shaohua. This provides a scalable
framework for implementing scalable priotization - particularly for
blk-mq, but applicable to any type of block device. The interface is
marked experimental for now.
- Bucketized IO stats for IO polling from Stephen Bates. This improves
efficiency of polled workloads in the presence of mixed block size
IO.
- A few fixes for opal, from Scott.
- A few pulls for NVMe, including a lot of fixes for NVMe-over-fabrics.
From a variety of folks, mostly Sagi and James Smart.
- A series from Bart, improving our exposed info and capabilities from
the blk-mq debugfs support.
- A series from Christoph, cleaning up how handle WRITE_ZEROES.
- A series from Christoph, cleaning up the block layer handling of how
we track errors in a request. On top of being a nice cleanup, it also
shrinks the size of struct request a bit.
- Removal of mg_disk and hd (sorry Linus) by Christoph. The former was
never used by platforms, and the latter has outlived it's usefulness.
- Various little bug fixes and cleanups from a wide variety of folks.
* 'for-4.12/block' of git://git.kernel.dk/linux-block: (329 commits)
block: hide badblocks attribute by default
blk-mq: unify hctx delay_work and run_work
block: add kblock_mod_delayed_work_on()
blk-mq: unify hctx delayed_run_work and run_work
nbd: fix use after free on module unload
MAINTAINERS: bfq: Add Paolo as maintainer for the BFQ I/O scheduler
blk-mq-sched: alloate reserved tags out of normal pool
mtip32xx: use runtime tag to initialize command header
scsi: Implement blk_mq_ops.show_rq()
blk-mq: Add blk_mq_ops.show_rq()
blk-mq: Show operation, cmd_flags and rq_flags names
blk-mq: Make blk_flags_show() callers append a newline character
blk-mq: Move the "state" debugfs attribute one level down
blk-mq: Unregister debugfs attributes earlier
blk-mq: Only unregister hctxs for which registration succeeded
blk-mq-debugfs: Rename functions for registering and unregistering the mq directory
blk-mq: Let blk_mq_debugfs_register() look up the queue name
blk-mq: Register <dev>/queue/mq after having registered <dev>/queue
ide-pm: always pass 0 error to ide_complete_rq in ide_do_devset
ide-pm: always pass 0 error to __blk_end_request_all
..
Some hosts controllers, like Cavium, needs to know whether the card
operates in byte- or block-address mode. Therefore export a new API,
mmc_card_is_blockaddr(), which provides this information.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Steven J. Hill <Steven.Hill@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
The host may issue an I/O abort by writing to the CCCR at any time
during I/O read operation via CMD52. And host may need suspend
transcation during write busy stage in SDIO suspend/resume scenario.
>From other side, a card may accept CMD52 during data transfer phase.
Previous implement would block issuing above command in busy stage.
It cause function driver can't implement as proper way and has no
opportunity to do some coverage in error case via I/O abort etc.
We need bypass some necessary operation during busy check stage.
Signed-off-by: Jiajie Hao <jiajie.hao@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Annotate big endian values correctly and make sparse happy.
In mmc_app_send_scr remove scr function parameter as it was
updating card->raw_scr anyway.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We have this construction:
if (a && b && !c)
finalize;
else
block;
finalize;
Which is equivalent by boolean logic to:
if (!a || !b || c)
block;
finalize;
Which is simpler code.
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_wait_for_data_req_done() is called in exactly one place,
and having it spread out is making things hard to oversee.
Factor this function into mmc_finalize_areq().
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
"previous" is a better name for the variable storing the previous
asynchronous request, better than the opaque name "data" atleast.
We see that we assign the return status to the returned variable
on all code paths, so we might as well just do that immediately
after calling mmc_finalize_areq().
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation to reuse the code for CQE support.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation to reuse the code for CQE support.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out data preparation into a separate function mmc_blk_data_prep()
which can be re-used for command queuing.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_apply_rel_rw() will be used by Software Command Queuing also. In that
case the command argument is not the block address so change
mmc_apply_rel_rw() to get block address from the request.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
RPMB does not allow Command Queue commands. Disable and re-enable the
Command Queue when switching.
Note that the driver only switches partitions when the queue is empty.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Harjani Ritesh <riteshh@codeaurora.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Normal read and write commands may not be used while the command queue is
enabled. Disable the Command Queue when mmc_test is probed and re-enable it
when it is removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Harjani Ritesh <riteshh@codeaurora.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson