Since [1], the erase argument for mmc_erase() function is saved in
erase_arg field of card structure. It is preferable to use it instead of
hard-coded MMC_SECURE_ERASE_ARG, which from eMMC 4.51 spec is not
recommended:
"6.6.16 Secure Erase
NOTE Secure Erase is included for backwards compatibility. New system
level implementations (based on v4.51 devices and beyond) should use
Erase combined with Sanitize instead of secure erase."
On STM32MP157C-EV1 board, embedding a THGBMDG5D1LBAIL eMMC, using
MMC_ERASE command with MMC_SECURE_ERASE_ARG may stuck the STM32 SDMMC IP,
if test 37 or test 38 are launched just after a write test, e.g. test 36.
Using the default MMC_ERASE argument from framework with erase_arg,
which default in our case to MMC_DISCARD_ARG does no more trig the
issue.
[1] commit 01904ff776 ("mmc: core: Calculate the discard arg only once")
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210209145214.10518-1-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC_CQE_QUEUE_FULL is not set and is only cleared.
Therefore, define is unnecessary.
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210203072014.30272-1-cw9316.lee@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
From the 4.19 kernel, thread related code has been removed in queue.c.
So we can exclude unnecessary header file.
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Acked-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20210125064355.28545-1-cw9316.lee@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for adding CQHCI crypto engine (inline encryption)
support, add the code required to make mmc_core and mmc_block aware of
inline encryption. Specifically:
- Add a capability flag MMC_CAP2_CRYPTO to struct mmc_host. Drivers
will set this if the host and driver support inline encryption.
- Embed a blk_keyslot_manager in struct mmc_host. Drivers will
initialize this (as a device-managed resource) if the host and driver
support inline encryption. mmc_block registers this keyslot manager
with the request_queue of any MMC card attached to the host.
- Make mmc_block copy the crypto keyslot and crypto data unit number
from struct request to struct mmc_request, so that drivers will have
access to them.
- If the MMC host is reset, reprogram all the keyslots to ensure that
the software state stays in sync with the hardware state.
Co-developed-by: Satya Tangirala <satyat@google.com>
Signed-off-by: Satya Tangirala <satyat@google.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Satya Tangirala <satyat@google.com>
Reviewed-and-tested-by: Peng Zhou <peng.zhou@mediatek.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210126001456.382989-2-ebiggers@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_test_cleanup() has same body as __mmc_test_prepare() with write
except the character to memset().
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20210119073705.375-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since it's doing nothing for shutdown behavior. And the callback will
be checked firstly in mmc_bus_shutdown().
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20210119051425.305-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The host parameter is not used in the body of mmc_sd_get_csd(),
so let's remove it. Update related code at the same time.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20210118084520.241-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers for MMC hosts that accept phase corrections can take advantage
of the helper by embedding an instance of struct mmc_clk_phase_map in
their private data and invoking mmc_of_parse_clk_phase() to extract
phase parameters. It is the responsibility of the host driver to
translate and apply the extracted values to hardware as required.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210114031433.2388532-2-andrew@aj.id.au
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Note that only _mmc_suspend() will call mmc_can_sleep(). And card is
checked before in mmc_can_poweroff_notify().
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20210115034506.646-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If extended CSD was not available, the eMMC driver would incorrectly
set the block size to 0, as the data_sector_size field of ext_csd
was never initialized. This issue was exposed by commit 817046ecdd
("block: Align max_hw_sectors to logical blocksize") which caused
max_sectors and max_hw_sectors to be set to 0 after setting the block
size to 0, resulting in a kernel panic in bio_split when attempting
to read from the device. Fix it by only reading the block size from
ext_csd if it is available.
Fixes: a5075eb948 ("mmc: block: Allow disabling 512B sector size emulation")
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Link: https://linux-review.googlesource.com/id/If244d178da4d86b52034459438fec295b02d6e60
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210114201405.2934886-1-pcc@google.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The CMD13 polling is needed for commands with R1B responses. In commit
a0d4c7eb71 ("mmc: block: Add CMD13 polling for MMC IOCTLS with R1B
response"), the intent was to introduce this for requests targeted to the
RPMB partition. However, the condition to trigger the polling loop became
wrong, leading to unnecessary polling. Let's fix the condition to avoid
this.
Fixes: a0d4c7eb71 ("mmc: block: Add CMD13 polling for MMC IOCTLS with R1B response")
Cc: stable@vger.kernel.org
Reported-by: Zhan Liu <zliua@micron.com>
Signed-off-by: Zhan Liu <zliua@micron.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Link: https://lore.kernel.org/r/20201202202320.22165-1-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the SD specification v7.10 the SD express card has been added. This new
type of removable SD card, can be managed via a PCIe/NVMe based interface,
while also allowing backwards compatibility towards the legacy SD
interface.
To keep the backwards compatibility, it's required to start the
initialization through the legacy SD interface. If it turns out that the
mmc host and the SD card, both supports the PCIe/NVMe interface, then a
switch should be allowed.
Therefore, let's introduce some basic support for this type of SD cards to
the mmc core. The mmc host, should set MMC_CAP2_SD_EXP if it supports this
interface and MMC_CAP2_SD_EXP_1_2V, if also 1.2V is supported, as to inform
the core about it.
To deal with the switch to the PCIe/NVMe interface, the mmc host is
required to implement a new host ops, ->init_sd_express(). Based on the
initial communication between the host and the card, host->ios.timing is
set to either MMC_TIMING_SD_EXP or MMC_TIMING_SD_EXP_1_2V, depending on if
1.2V is supported or not. In this way, the mmc host can check these values
in its ->init_sd_express() ops, to know how to proceed with the handover.
Note that, to manage card insert/removal, the mmc core sticks with using
the ->get_cd() callback, which means it's the host's responsibility to make
sure it provides valid data, even if the card may be managed by PCIe/NVMe
at the moment. As long as the card seems to be present, the mmc core keeps
the card powered on.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Rui Feng <rui_feng@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/1603936636-3126-1-git-send-email-rui_feng@realsil.com.cn
-----BEGIN PGP SIGNATURE-----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=LzyE
-----END PGP SIGNATURE-----
Merge tag 'block-5.10-2020-10-12' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- Series of merge handling cleanups (Baolin, Christoph)
- Series of blk-throttle fixes and cleanups (Baolin)
- Series cleaning up BDI, seperating the block device from the
backing_dev_info (Christoph)
- Removal of bdget() as a generic API (Christoph)
- Removal of blkdev_get() as a generic API (Christoph)
- Cleanup of is-partition checks (Christoph)
- Series reworking disk revalidation (Christoph)
- Series cleaning up bio flags (Christoph)
- bio crypt fixes (Eric)
- IO stats inflight tweak (Gabriel)
- blk-mq tags fixes (Hannes)
- Buffer invalidation fixes (Jan)
- Allow soft limits for zone append (Johannes)
- Shared tag set improvements (John, Kashyap)
- Allow IOPRIO_CLASS_RT for CAP_SYS_NICE (Khazhismel)
- DM no-wait support (Mike, Konstantin)
- Request allocation improvements (Ming)
- Allow md/dm/bcache to use IO stat helpers (Song)
- Series improving blk-iocost (Tejun)
- Various cleanups (Geert, Damien, Danny, Julia, Tetsuo, Tian, Wang,
Xianting, Yang, Yufen, yangerkun)
* tag 'block-5.10-2020-10-12' of git://git.kernel.dk/linux-block: (191 commits)
block: fix uapi blkzoned.h comments
blk-mq: move cancel of hctx->run_work to the front of blk_exit_queue
blk-mq: get rid of the dead flush handle code path
block: get rid of unnecessary local variable
block: fix comment and add lockdep assert
blk-mq: use helper function to test hw stopped
block: use helper function to test queue register
block: remove redundant mq check
block: invoke blk_mq_exit_sched no matter whether have .exit_sched
percpu_ref: don't refer to ref->data if it isn't allocated
block: ratelimit handle_bad_sector() message
blk-throttle: Re-use the throtl_set_slice_end()
blk-throttle: Open code __throtl_de/enqueue_tg()
blk-throttle: Move service tree validation out of the throtl_rb_first()
blk-throttle: Move the list operation after list validation
blk-throttle: Fix IO hang for a corner case
blk-throttle: Avoid tracking latency if low limit is invalid
blk-throttle: Avoid getting the current time if tg->last_finish_time is 0
blk-throttle: Remove a meaningless parameter for throtl_downgrade_state()
block: Remove redundant 'return' statement
...
In mmc_queue_setup_discard() the mmc driver queue's discard_granularity
might be set as 0 (when card->pref_erase > max_discard) while the mmc
device still declares to support discard operation. This is buggy and
triggered the following kernel warning message,
WARNING: CPU: 0 PID: 135 at __blkdev_issue_discard+0x200/0x294
CPU: 0 PID: 135 Comm: f2fs_discard-17 Not tainted 5.9.0-rc6 #1
Hardware name: Google Kevin (DT)
pstate: 00000005 (nzcv daif -PAN -UAO BTYPE=--)
pc : __blkdev_issue_discard+0x200/0x294
lr : __blkdev_issue_discard+0x54/0x294
sp : ffff800011dd3b10
x29: ffff800011dd3b10 x28: 0000000000000000 x27: ffff800011dd3cc4 x26: ffff800011dd3e18 x25: 000000000004e69b x24: 0000000000000c40 x23: ffff0000f1deaaf0 x22: ffff0000f2849200 x21: 00000000002734d8 x20: 0000000000000008 x19: 0000000000000000 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 x14: 0000000000000394 x13: 0000000000000000 x12: 0000000000000000 x11: 0000000000000000 x10: 00000000000008b0 x9 : ffff800011dd3cb0 x8 : 000000000004e69b x7 : 0000000000000000 x6 : ffff0000f1926400 x5 : ffff0000f1940800 x4 : 0000000000000000 x3 : 0000000000000c40 x2 : 0000000000000008 x1 : 00000000002734d8 x0 : 0000000000000000 Call trace:
__blkdev_issue_discard+0x200/0x294
__submit_discard_cmd+0x128/0x374
__issue_discard_cmd_orderly+0x188/0x244
__issue_discard_cmd+0x2e8/0x33c
issue_discard_thread+0xe8/0x2f0
kthread+0x11c/0x120
ret_from_fork+0x10/0x1c
---[ end trace e4c8023d33dfe77a ]---
This patch fixes the issue by setting discard_granularity as SECTOR_SIZE
instead of 0 when (card->pref_erase > max_discard) is true. Now no more
complain from __blkdev_issue_discard() for the improper value of discard
granularity.
This issue is exposed after commit b35fd7422c ("block: check queue's
limits.discard_granularity in __blkdev_issue_discard()"), a "Fixes:" tag
is also added for the commit to make sure people won't miss this patch
after applying the change of __blkdev_issue_discard().
Fixes: e056a1b5b6 ("mmc: queue: let host controllers specify maximum discard timeout")
Fixes: b35fd7422c ("block: check queue's limits.discard_granularity in __blkdev_issue_discard()").
Reported-and-tested-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20201002013852.51968-1-colyli@suse.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a littler helper to make the somewhat arcane bd_contains checks a
little more obvious.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The BDI_CAP_STABLE_WRITES is one of the few bits of information in the
backing_dev_info shared between the block drivers and the writeback code.
To help untangling the dependency replace it with a queue flag and a
superblock flag derived from it. This also helps with the case of e.g.
a file system requiring stable writes due to its own checksumming, but
not forcing it on other users of the block device like the swap code.
One downside is that we an't support the stable_pages_required bdi
attribute in sysfs anymore. It is replaced with a queue attribute which
also is writable for easier testing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reorganize the code, so that the flag is always cleared independently of
a good or bad case.
Fixes: 97a7d87e96 ("mmc: core: add a 'doing_init_tune' flag and a 'mmc_doing_tune' helper")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200914112845.21855-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We already have 'host' as a variable, so use it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200901150250.26236-5-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Our driver needs to know when tuning is in progress. 'doing_retune' only
covers re-tuning, not the initial tuning. Add another flag to detect the
initial tuning state and add a helper which tells us if any kind of
tuning is going on. Only implemented for MMC currently because that's
where we need it. SD can be added later if it becomes necessary.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200901150250.26236-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver specific downgrade function makes more sense if we run it
before we set the timing to something lower, not after. Otherwise some
non-HS400 communication has already happened.
No need to convert users. There is only one currently which needs this
change in a following patch.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200901150250.26236-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As with GPIO, UART and others, allow specifying the device index via the
aliases node in the device tree.
On embedded devices, there is often a combination of removable (e.g.
SD card) and non-removable MMC devices (e.g. eMMC).
Therefore the index might change depending on
* host of removable device
* removable card present or not
This makes it difficult to hardcode the root device, if it is on the
non-removable device. E.g. if SD card is present eMMC will be mmcblk1,
if SD card is not present at boot, eMMC will be mmcblk0.
Alternative solutions like PARTUUIDs do not cover the case where multiple
mmcblk devices contain the same image. This is a common issue on devices
that can boot both from eMMC (for regular boot) and SD cards (as a
temporary boot medium for development). When a firmware image is
installed to eMMC after a test boot via SD card, there will be no
reliable way to refer to a specific device using (PART)UUIDs oder
LABELs.
The demand for this feature has led to multiple attempts to implement
it, dating back at least to 2012 (see
https://www.spinics.net/lists/linux-mmc/msg26586.html for a previous
discussion from 2014).
All indices defined in the aliases node will be reserved for use by the
respective MMC device, moving the indices of devices that don't have an
alias up into the non-reserved range. If the aliases node is not found,
the driver will act as before.
This is a rebased and cleaned up version of
https://www.spinics.net/lists/linux-mmc/msg26588.html .
Based-on-patch-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lkml.org/lkml/2020/8/5/194
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20200901085004.2512-2-matthias.schiffer@ew.tq-group.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When reading the test description, I thought a correction of the
xfer_size was tested, which is not the case. It is tested that the
xfer_size is correct. Use 'proper xfer_size' to remove this ambiguity.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200817115838.2981-1-wsa@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For SDIO functions, SDIO cards and SD COMBO cards are exported revision
number and info strings from CISTPL_VERS_1 structure. Revision number
should indicate compliance of standard and info strings should contain
product information in same format as product information for PCMCIA cards.
Product information for PCMCIA cards should contain following strings in
this order: Manufacturer, Product Name, Lot number, Programming Conditions.
Note that not all SDIO cards export all those info strings in that order as
described in PCMCIA Metaformat Specification.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200727133837.19086-5-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Before parsing CISTPL_VERS_1 structure check that its size is at least two
bytes to prevent buffer overflow.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200727133837.19086-2-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI changed from using a tasklet to finish requests, to using an IRQ
thread i.e. commit c07a48c265 ("mmc: sdhci: Remove finish_tasklet").
Because this increased the latency to complete requests, a preparatory
change was made to complete the request from the IRQ handler if
possible i.e. commit 19d2f695f4 ("mmc: sdhci: Call mmc_request_done()
from IRQ handler if possible"). That alleviated the situation for MMC
block devices because the MMC block driver makes use of mmc_pre_req()
and mmc_post_req() so that successful requests are completed in the IRQ
handler and any DMA unmapping is handled separately in mmc_post_req().
However SDIO was still affected, and an example has been reported with
up to 20% degradation in performance.
Looking at SDIO I/O helper functions, sdio_io_rw_ext_helper() appeared
to be a possible candidate for making use of asynchronous requests
within its I/O loops, but analysis revealed that these loops almost
never iterate more than once, so the complexity of the change would not
be warrented.
Instead, mmc_pre_req() and mmc_post_req() are added before and after I/O
submission (mmc_wait_for_req) in mmc_io_rw_extended(). This still has
the potential benefit of reducing the duration of interrupt handlers, as
well as addressing the latency issue for SDHCI. It also seems a more
reasonable solution than forcing drivers to do everything in the IRQ
handler.
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Fixes: c07a48c265 ("mmc: sdhci: Remove finish_tasklet")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200903082007.18715-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
static priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low' priority level,
plus sched_set_normal() to set the policy back to non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in a separate
tree.
When merging to the latest upstream tree there's a conflict in drivers/spi/spi.c,
which can be resolved via:
sched_set_fifo(ctlr->kworker_task);
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=/7JH
-----END PGP SIGNATURE-----
Merge tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull sched/fifo updates from Ingo Molnar:
"This adds the sched_set_fifo*() encapsulation APIs to remove static
priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low'
priority level, plus sched_set_normal() to set the policy back to
non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in
a separate tree"
* tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
sched,tracing: Convert to sched_set_fifo()
sched: Remove sched_set_*() return value
sched: Remove sched_setscheduler*() EXPORTs
sched,psi: Convert to sched_set_fifo_low()
sched,rcutorture: Convert to sched_set_fifo_low()
sched,rcuperf: Convert to sched_set_fifo_low()
sched,locktorture: Convert to sched_set_fifo()
sched,irq: Convert to sched_set_fifo()
sched,watchdog: Convert to sched_set_fifo()
sched,serial: Convert to sched_set_fifo()
sched,powerclamp: Convert to sched_set_fifo()
sched,ion: Convert to sched_set_normal()
sched,powercap: Convert to sched_set_fifo*()
sched,spi: Convert to sched_set_fifo*()
sched,mmc: Convert to sched_set_fifo*()
sched,ivtv: Convert to sched_set_fifo*()
sched,drm/scheduler: Convert to sched_set_fifo*()
sched,msm: Convert to sched_set_fifo*()
sched,psci: Convert to sched_set_fifo*()
sched,drbd: Convert to sched_set_fifo*()
...
- Add a new host cap bit and a corresponding DT property, to support power
cycling of the card by FW at system suspend/resume.
- Fix clock rate setting for SDIO in SDR12/SDR25 speed-mode
- Fix switch to 1/4-bit mode at system suspend/resume for SD-combo cards
- Convert the mmc-pwrseq DT bindings to the json-schema
- Always allow the card detect uevent to be consumed by userspace
MMC host:
- Convert a few DT bindings to the json-schema
- mtk-sd: Add support for command queue through cqhci
- mtk-sd: Add support for the MT6779 variant
- renesas_sdhi_internal_dmac: Fix dma unmapping in the error path
- sdhci_am654: Add support for the AM65x PG2.0 variant
- sdhci_am654: Extend support for phys/clocks
- sdhci-cadence: Drop incorrect HW tuning for SD mode
- sdhci-msm: Add support for interconnect bandwidth scaling
- sdhci-msm: Enable internal voltage control
- sdhci-msm: Enable low power state for pinctrls
- sdhci-of-at91: Ludovic Desroches handovers maintenance to Eugen Hristev
- sdhci-pci-gli: Improve clock handling for GL975x
- sdhci-pci-o2micro: Add HW tuning for SDR104 mode
- sdhci-pci-o2micro: Fix support for O2 host controller Seabird1
-----BEGIN PGP SIGNATURE-----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=AwwR
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add a new host cap bit and a corresponding DT property, to support
power cycling of the card by FW at system suspend/resume.
- Fix clock rate setting for SDIO in SDR12/SDR25 speed-mode
- Fix switch to 1/4-bit mode at system suspend/resume for SD-combo
cards
- Convert the mmc-pwrseq DT bindings to the json-schema
- Always allow the card detect uevent to be consumed by userspace
MMC host controllers:
- Convert a few DT bindings to the json-schema
- mtk-sd:
- Add support for command queue through cqhci
- Add support for the MT6779 variant
- renesas_sdhi_internal_dmac:
- Fix dma unmapping in the error path
- sdhci_am654:
- Add support for the AM65x PG2.0 variant
- Extend support for phys/clocks
- sdhci-cadence:
- Drop incorrect HW tuning for SD mode
- sdhci-msm:
- Add support for interconnect bandwidth scaling
- Enable internal voltage control
- Enable low power state for pinctrls
- sdhci-of-at91:
- Ludovic Desroches handovers maintenance to Eugen Hristev
- sdhci-pci-gli:
- Improve clock handling for GL975x
- sdhci-pci-o2micro:
- Add HW tuning for SDR104 mode
- Fix support for O2 host controller Seabird1"
* tag 'mmc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (66 commits)
mmc: mediatek: make function msdc_cqe_disable() static
MAINTAINERS: mmc: sdhci-of-at91: handover maintenance to Eugen Hristev
dt-bindings: mmc: mediatek: Add document for mt6779
mmc: mediatek: command queue support
mmc: mediatek: refine msdc timeout api
mmc: mediatek: add MT6779 MMC driver support
mmc: sdhci-pci-o2micro: Add HW tuning for SDR104 mode
mmc: sdhci-pci-o2micro: Bug fix for O2 host controller Seabird1
mmc: via-sdmmc: use generic power management
memstick: jmb38x_ms: use generic power management
mmc: sdhci-cadence: do not use hardware tuning for SD mode
mmc: sdhci-pci-gli: Set SDR104's clock to 205MHz and enable SSC for GL975x
mmc: cqhci: Fix a print format for the task descriptor
mmc: sdhci-of-arasan: fix timings allocation code
mmc: sdhci: Fix a potential uninitialized variable
dt-bindings: mmc: renesas,sdhi: convert to YAML
dt-bindings: mmc: convert arasan sdhci bindings to yaml
mmc: sdhci: Fix potential null pointer access while accessing vqmmc
mmc: core: Add MMC_CAP2_FULL_PWR_CYCLE_IN_SUSPEND
dt-bindings: mmc: Add full-pwr-cycle-in-suspend property
...
The commit 5a36d6bcdf ("mmc: core: Add DT-bindings for
MMC_CAP2_FULL_PWR_CYCLE") added the "full-pwr-cycle" property which
is possible to perform a full power cycle of the card at any time.
However, some environment (like r8a77951-salvator-xs) is possible
to perform a full power cycle of the card in suspend via firmware
(PSCI on arm-trusted-firmware). So, in worst case, since we are
not doing a graceful shutdown of the eMMC device (just cut VCCQ
while the eMMC is "sleeping") in suspend, it could lead to internal
data corruptions. So, add MMC_CAP2_FULL_PWR_CYCLE_IN_SUSPEND
to do a graceful shutdown which issues Power Off notification
before entering system suspend.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1594123122-13156-3-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Correcting this misspelling squashes the following W=1 build warning(s):
mmc/core/queue.c:212: warning: Function parameter or member 'mq' not described in '__mmc_init_request'
mmc/core/queue.c:212: warning: Excess function parameter 'q' description in '__mmc_init_request'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-8-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remainder of the kerneldoc descriptions look present and correct.
Fixes the following W=1 kernel build warnings:
drivers/mmc/core/regulator.c:178: warning: Function parameter or member 'mmc' not described in 'mmc_regulator_set_vqmmc'
drivers/mmc/core/regulator.c:178: warning: Function parameter or member 'ios' not described in 'mmc_regulator_set_vqmmc'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-4-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add missing kerneldoc entry for sdio_set_host_pm_flags()'s 'flag'
function argument.
Fixes the following W=1 kernel build warning:
kernel/drivers/mmc/core/sdio_io.c:722: warning: Function parameter or member 'flags' not described in 'sdio_set_host_pm_flags'
Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-3-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Not all source files which include quirks.h make use of the all of
the available fixup information. When this happens the compiler
complains that some constant variables are defined by never used.
We can fix this by telling the compiler that this intentional by
simply marking them as __maybe_unused.
Fixes the following W=1 kernel build warnings:
In file included from drivers/mmc/core/sdio.c:22:
drivers/mmc/core/quirks.h:105:31: warning: ‘mmc_ext_csd_fixups’ defined but not used [-Wunused-const-variable=]
105 | static const struct mmc_fixup mmc_ext_csd_fixups[] = {
| ^~~~~~~~~~~~~~~~~~
drivers/mmc/core/quirks.h:17:31: warning: ‘mmc_blk_fixups’ defined but not used [-Wunused-const-variable=]
17 | static const struct mmc_fixup mmc_blk_fixups[] = {
| ^~~~~~~~~~~~~~
In file included from drivers/mmc/core/mmc.c:25:
drivers/mmc/core/quirks.h:123:31: warning: ‘sdio_fixup_methods’ defined but not used [-Wunused-const-variable=]
123 | static const struct mmc_fixup sdio_fixup_methods[] = {
| ^~~~~~~~~~~~~~~~~~
drivers/mmc/core/quirks.h:17:31: warning: ‘mmc_blk_fixups’ defined but not used [-Wunused-const-variable=]
17 | static const struct mmc_fixup mmc_blk_fixups[] = {
| ^~~~~~~~~~~~~~
Cc: Andrei Warkentin <andreiw@motorola.com>
Cc: Martin Mares <mj@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200701124702.908713-2-lee.jones@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set the default power mode, MMC_POWER_UNDEFINED, in mmc_alloc_host() rather
than in mmc_start_host(). This enables host drivers to make use of the
initial state during ->probe().
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org> Link:
https://lore.kernel.org/r/1592919288-1020-3-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In current code logic, when work in SDR12/SDR25 mode, the final clock
rate is incorrect, just the legancy 400KHz, because the
card->sw_caps.sd3_bus_mode do not has the flag SD_MODE_UHS_SDR12 or
SD_MODE_UHS_SDR25. Besides, SDIO_SPEED_SDR12 is actually value 0, and
every mode need to config the timing and clock rate, so remove the
‘if’ operator.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Tested-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/1592813959-5914-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 6b5eda369a ("sdio: put active devices into 1-bit mode during
suspend") disabled 4-bit mode during system suspend. After this patch,
commit 7310ece86a ("mmc: implement SD-combo (IO+mem) support") used
new sdio_enable_4bit_bus() instead of sdio_enable_wide() to support
SD-combo cards, also for card resume. However, no corresponding support
added during suspend. That is not correct. Let's fix it.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20200609081431.6376-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the card type is SD combo(MMC_TYPE_SD_COMBO) and the memory part does
not support wider bus(SD_SCR_BUS_WIDTH_4), nothing will be done except
return 0. However, we should check whether IO part support wider bus or
not. We should use available IO ability if supported.
In addition, there's a duplicated check to MMC_CAP_4_BIT_DATA since
sdio_enable_wide() will include that check. And we can also save one
call site to sdio_enable_wide() after this change.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20200608103009.5000-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We should return any possible error returned by mmc_io_rw_direct()
rather than only -EIO in sdio_disable_func() failure path.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200604100102.13572-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The approach to allow userspace ~5s to consume the uevent, which is
triggered when a new card is inserted/initialized, currently requires the
mmc host to support system wakeup.
This is unnecessary limiting, especially for an mmc host that relies on a
GPIO IRQ for card detect. More precisely, the mmc host may not support
system wakeup for its corresponding struct device, while the GPIO IRQ still
could be configured as a wakeup IRQ via enable_irq_wake().
To support all various cases, let's simply drop the need for the wakeup
support. Instead let's always register a wakeup source and activate it for
all card detect IRQs by calling __pm_wakeup_event().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200529102341.12529-1-ulf.hansson@linaro.org
The mmc driver doesn't support event notifications, which means
that check_disk_change is a no-op.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the call to blk_should_fake_timeout out of blk_mq_complete_request
and into the drivers, skipping call sites that are obvious error
handlers, and remove the now superflous blk_mq_force_complete_rq helper.
This ensures we don't keep injecting errors into completions that just
terminate the Linux request after the hardware has been reset or the
command has been aborted.
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Because SCHED_FIFO is a broken scheduler model (see previous patches)
take away the priority field, the kernel can't possibly make an
informed decision.
In this case, use fifo_low, because it only cares about being above
SCHED_NORMAL. Effectively no change in behaviour.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Device/vendor ids from Common CIS (Card Information Structure) may be
different as device/vendor ids from CIS on particular SDIO function.
Kernel currently exports only device/vendor ids from SDIO functions and not
"main" device/vendor ids from Common CIS.
This patch exports "main" device/vendor ids for SDIO and SD combo cards at
top level mmc device in sysfs hierarchy.
Userspace can use e.g. udev rules to correctly match whole SDIO card based
on Common CIS device/vendor id and not only one particular SDIO function.
Having this information in userspace also helps developers to debug whole
SDIO card as e.g. kernel mmc quirks use device/vendor ids from Common CIS
and not from particular SDIO function. Also it allows to write userspace
applications which list all connected SDIO cards based on CIS ids.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Link: https://lore.kernel.org/r/20200527110858.17504-2-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDIO non-combo cards are not handled by mmc_block driver and do not have
accessible CID register which is used for MMC_NAME= construction.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Link: https://lore.kernel.org/r/20200527110858.17504-1-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Marvell SDIO device ID 0x9134 is used in SDIO Common CIS (Card Information
Structure) and not in SDIO wlan function (with ID 1). SDIO Common CIS is
accessed by function ID 0.
So change this misleading macro name to SDIO_DEVICE_ID_MARVELL_8887_F0 as
it does not refer to wlan function. It refers to function 0.
Wlan module on this SDIO card is available at function ID 1 and is
identified by different SDIO device ID 0x9135. Kernel quirks for SDIO
devices are matched against device ID from SDIO Common CIS. Therefore
device ID used in quirk is correct, just has misleading name.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-2-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Step by step, mmc host drivers and the mmc core have been improved in
regards to support erase/discard/trim operations. We have now reached a
point when it no longer seems reasonable to use an opt-in approach to
enable the functionality. Therefore, let's switch to make the operations
always supported.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200508112853.23525-1-ulf.hansson@linaro.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Following eMMC JEDEC JESD84-B51 standard, an enhanced form of
rpmb is supported. What this enhanced mode supports is in addition
to be able to write one rpmb or two rpmb frames at a time,
32 frames can be written at a time.
Expose this information present in ext csd field so that the
user space application that wants to make use of this can do so.
Signed-off-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1588341189-4371-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the comment in mmc_sdio_reinit_card(), some SDIO cards may
require a "[CMD5,5,3,7] init sequence", which isn't always obeyed in
mmc_sdio_init_card(). Especially, when we end up retrying the UHS-I
specific initialization, there is a missing CMD5.
Let's update the code to make the behaviour consistent and let's also take
the opportunity to clean up the code a bit, to avoid open coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200430091640.455-5-ulf.hansson@linaro.org
While initializing an SDIO card in mmc_sdio_init_card(), we may need to
retry the UHS-I specific initialization, in case the first attempt fails.
This leads to resending a CMD8, but also to restart from scratch with the
so called OCR mask negotiations. This is unnecessary as we already have a
negotiated OCR mask, so let's use that instead. In this way, the behaviour
also becomes more consistent with other similar paths.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200430091640.455-4-ulf.hansson@linaro.org
Over the years, the code in mmc_sdio_init_card() has grown to become quite
messy. Unfortunate this has also lead to that several paths are leaking
memory in form of an allocated struct mmc_card, which includes additional
data, such as initialized struct device for example.
Unfortunate, it's a too complex task find each offending commit. Therefore,
this change fixes all memory leaks at once.
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200430091640.455-3-ulf.hansson@linaro.org
During some scenarios mmc_sdio_init_card() runs a retry path for the UHS-I
specific initialization, which leads to removal of the previously allocated
card. A new card is then re-allocated while retrying.
However, in one of the corresponding error paths we may end up to remove an
already removed card, which likely leads to a NULL pointer exception. So,
let's fix this.
Fixes: 5fc3d80ef4 ("mmc: sdio: don't use rocr to check if the card could support UHS mode")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200430091640.455-2-ulf.hansson@linaro.org
Fixes coccicheck warning:
drivers/mmc/core/debugfs.c:222:0-23: WARNING: mmc_clock_fops should be
defined with DEFINE_DEBUGFS_ATTRIBUTE
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files
Fixes: 703aae3d09 ("mmc: add a file to debugfs for changing host clock at runtime")
Fixes: a04c50aaa9 ("mmc: core: no need to check return value of debugfs_create functions")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1587633319-19835-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the well defined HIGH_SPEED_BUS_SPEED macro in mmc_sd_switch_hs()
to make code more readable.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200410145643.630b0731@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adjust mmc_regulator_set_vqmmc() to return 1 if the voltage switch was
skipped because the regulator voltage was already correct. This allows
drivers to detect such condition and possibly skip various voltage
switching extras.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20200416163649.336967-2-marex@denx.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The data structure member “rpmb->md” was passed to a call of the function
“mmc_blk_put” after a call of the function “put_device”. Reorder these
function calls to keep the data accesses consistent.
Fixes: 1c87f73578 ("mmc: block: Fix bug when removing RPMB chardev ")
Signed-off-by: Peng Hao <richard.peng@oppo.com>
Cc: stable@vger.kernel.org
[Uffe: Fixed up mangled patch and updated commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
First, it should be noted that the CQE timeout (60 seconds) is substantial
so a CQE request that times out is really stuck, and the race between
timeout and completion is extremely unlikely. Nevertheless this patch
fixes an issue with it.
Commit ad73d6fead ("mmc: complete requests from ->timeout")
preserved the existing functionality, to complete the request.
However that had only been necessary because the block layer
timeout handler had been marking the request to prevent it from being
completed normally. That restriction was removed at the same time, the
result being that a request that has gone will have been completed anyway.
That is, the completion was unnecessary.
At the time, the unnecessary completion was harmless because the block
layer would ignore it, although that changed in kernel v5.0.
Note for stable, this patch will not apply cleanly without patch "mmc:
core: Fix recursive locking issue in CQE recovery path"
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: ad73d6fead ("mmc: complete requests from ->timeout")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200508062227.23144-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Consider the following stack trace
-001|raw_spin_lock_irqsave
-002|mmc_blk_cqe_complete_rq
-003|__blk_mq_complete_request(inline)
-003|blk_mq_complete_request(rq)
-004|mmc_cqe_timed_out(inline)
-004|mmc_mq_timed_out
mmc_mq_timed_out acquires the queue_lock for the first
time. The mmc_blk_cqe_complete_rq function also tries to acquire
the same queue lock resulting in recursive locking where the task
is spinning for the same lock which it has already acquired leading
to watchdog bark.
Fix this issue with the lock only for the required critical section.
Cc: <stable@vger.kernel.org>
Fixes: 1e8e55b670 ("mmc: block: Add CQE support")
Suggested-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Sarthak Garg <sartgarg@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1588868135-31783-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the request completion path with CQE, request type is being checked
after the request is getting completed. This is resulting in returning
the wrong request type and leading to the IO hang issue.
ASYNC request type is getting returned for DCMD type requests.
Because of this mismatch, mq->cqe_busy flag is never getting cleared
and the driver is not invoking blk_mq_hw_run_queue. So requests are not
getting dispatched to the LLD from the block layer.
All these eventually leading to IO hang issues.
So, get the request type before completing the request.
Cc: <stable@vger.kernel.org>
Fixes: 1e8e55b670 ("mmc: block: Add CQE support")
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1588775643-18037-2-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix the following sparse warning:
drivers/mmc/core/mmc_ops.c:881:5: warning: symbol 'mmc_interrupt_hpi'
was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Fixes: 55c2b8b9a3 ("mmc: core: Re-work the code for eMMC sanitize")
Link: https://lore.kernel.org/r/20200403034727.11879-1-yanaijie@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The error path for sanitize operations that completes with -ETIMEDOUT, is
tightly coupled with the internal request handling code of the core. More
precisely, mmc_wait_for_req_done() checks for specific sanitize errors.
This is not only inefficient as it affects all types of requests, but also
hackish.
Therefore, let's improve the behaviour by moving the error path out of the
mmc core. To do that, retuning needs to be held while running the sanitize
operation.
Moreover, to avoid exporting unnecessary symbols to the mmc block module,
let's move the code into the mmc_ops.c file. While updating the actual
code, let's also take the opportunity to clean up some of the mess around
it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200316152152.15122-1-ulf.hansson@linaro.org
Supply a separate sg list for each of the request in non-blocking
IO test cases where two requests will be issued at same time.
Otherwise, sg memory may get unmapped when a request is done while
same memory is being accessed by controller from the other request,
and it leads to iommu errors with below call stack:
__arm_lpae_unmap+0x2e0/0x478
arm_lpae_unmap+0x54/0x70
arm_smmu_unmap+0x64/0xa4
__iommu_unmap+0xb8/0x1f0
iommu_unmap_fast+0x38/0x48
__iommu_dma_unmap+0x88/0x108
iommu_dma_unmap_sg+0x90/0xa4
sdhci_post_req+0x5c/0x78
mmc_test_start_areq+0x10c/0x120 [mmc_test]
mmc_test_area_io_seq+0x150/0x264 [mmc_test]
mmc_test_rw_multiple+0x174/0x1c0 [mmc_test]
mmc_test_rw_multiple_sg_len+0x44/0x6c [mmc_test]
mmc_test_profile_sglen_wr_nonblock_perf+0x6c/0x94 [mmc_test]
mtf_test_write+0x238/0x3cc [mmc_test]
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582714668-17247-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case the host specify a max_busy_timeout, we need to validate that the
needed timeout for the HPI command conforms to that requirement. If that's
not the case, let's convert from a R1B response to a R1 response, as to
instruct the host to avoid HW busy detection.
Additionally, when R1B is used we must also inform the host about the busy
timeout for the command, so let's do that via updating cmd.busy_timeout.
Finally, when R1B is used and in case the host supports HW busy detection,
there should be no need for doing polling, so then skip that.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-12-ulf.hansson@linaro.org
Rather than open coding the polling loop in mmc_interrupt_hpi(), let's
convert to use mmc_poll_for_busy().
Note that, moving to mmc_poll_for_busy() for HPI also improves the
behaviour according to below.
- Adds support for polling via the optional ->card_busy() host ops.
- Require R1_READY_FOR_DATA to be set in the CMD13 response before exiting
the polling loop.
- Adds a throttling mechanism to avoid CPU hogging when polling.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-11-ulf.hansson@linaro.org
The 'u32 *status' is unused by the caller, so let's drop it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-10-ulf.hansson@linaro.org
Rather than open coding the polling loop in mmc_do_erase(), let's convert
to use mmc_poll_for_busy().
To allow a slightly different error parsing during polling, compared to the
__mmc_switch() case, a new in-parameter to mmc_poll_for_busy() is needed,
but other than that the conversion is straight forward.
Besides addressing the open coding issue, moving to mmc_poll_for_busy() for
erase/trim/discard improves the behaviour according to below.
- Adds support for polling via the optional ->card_busy() host ops.
- Returns zero to indicate success when the final polling attempt finds the
card non-busy, even if the timeout expired.
- Exits the polling loop when state moves to R1_STATE_TRAN, rather than
when leaving R1_STATE_PRG.
- Decreases the starting range for throttling to 32-64us.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-9-ulf.hansson@linaro.org
Through mmc_poll_for_busy() a CMD13 may be sent to get the status of the
(e)MMC card. If the state of the card is R1_STATE_PRG, the card is
considered as being busy, which means we continue to poll with CMD13. This
seems to be sufficient, but it's also unnecessary fragile, as it means a
new command/request could potentially be sent to the card when it's in an
unknown state.
To try to improve the situation, but also to move towards a more consistent
CMD13 polling behaviour in the mmc core, let's deploy the same policy we
use for regular I/O write requests. In other words, let's check that card
returns to the R1_STATE_TRAN and that the R1_READY_FOR_DATA bit is set in
the CMD13 response, before exiting the polling loop.
Note that, potentially this changed behaviour could lead to unnecessary
waiting for the timeout to expire, if the card for some reason, moves to an
unexpected error state. However, as we bail out from the polling loop when
R1_SWITCH_ERROR bit is set or when the CMD13 fails, this shouldn't be an
issue.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-8-ulf.hansson@linaro.org
To allow subsequent changes to re-use the code from the static function
mmc_blk_in_tran_state(), let's move it to a public header. While at it,
let's also rename it to mmc_ready_for_data(), as to try to better describe
its purpose.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-7-ulf.hansson@linaro.org
To make the code more readable, move the part that gets the busy status of
the card out into a separate function, mmc_busy_status(). Then call it from
mmc_poll_for_busy().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-6-ulf.hansson@linaro.org
The use_busy_signal in-parameter is set true by all callers of
__mmc_switch(), hence it's redundant so drop it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-5-ulf.hansson@linaro.org
To simplify code, let's extend mmc_switch_status() to cope with needs
addressed in __mmc_switch_status(). Then move all users to the updated
mmc_switch_status() API and drop __mmc_switch_status() altogether.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-4-ulf.hansson@linaro.org
The last user of MMC_OPS_TIMEOUT_MS was recently removed, however the
define stayed around. Let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-3-ulf.hansson@linaro.org
In mmc_poll_for_busy() we loop continuously, either by sending a CMD13 or
by invoking the ->card_busy() host ops, as to detect when the card stops
signaling busy. This behaviour is problematic as it may cause CPU hogging,
especially when the busy signal time reaches beyond a few ms.
Let's fix the issue by adding a throttling mechanism, that inserts a
usleep_range() in between the polling attempts. The sleep range starts at
32-64us, but increases for each loop by a factor of 2, up until the range
reaches ~32-64ms. In this way, we are able to keep the loop fine-grained
enough for short busy signaling times, while also not hogging the CPU for
longer times.
Note that, this change is inspired by the similar throttling mechanism that
we already use for mmc_do_erase().
Reported-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-2-ulf.hansson@linaro.org
Enable the MMC host software queue for the SD card if the host controller
supports the MMC host software queue.
On my Spreadtrum platform, I did not see any obvious performance changes
in 4K block size when changing to use hsq for the SD cards, I think the
reason is the SD card works at a low speed on my platform, and most of
time is spent in the hardware. But we can see some obvious improvements
when enabling the packed request based on hsq, that's why we still add hsq
support for the SD cards.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/0065b4631fef2d61c3b89d14a4ea4f2b7499ea56.1581478568.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now the MMC read/write stack will always wait for previous request is
completed by mmc_blk_rw_wait(), before sending a new request to hardware,
or queue a work to complete request, that will bring context switching
overhead and spend some extra time to poll the card for busy completion
for I/O writes via sending CMD13, especially for high I/O per second
rates, to affect the IO performance.
Thus this patch introduces MMC software queue interface based on the
hardware command queue engine's interfaces, which is similar with the
hardware command queue engine's idea, that can remove the context
switching. Moreover we set the default queue depth as 64 for software
queue, which allows more requests to be prepared, merged and inserted
into IO scheduler to improve performance, but we only allow 2 requests
in flight, that is enough to let the irq handler always trigger the
next request without a context switch, as well as avoiding a long latency.
Moreover the host controller should support HW busy detection for I/O
operations when enabling the host software queue. That means, the host
controller must not complete a data transfer request, until after the
card stops signals busy.
From the fio testing data in cover letter, we can see the software
queue can improve some performance with 4K block size, increasing
about 16% for random read, increasing about 90% for random write,
though no obvious improvement for sequential read and write.
Moreover we can expand the software queue interface to support MMC
packed request or packed command in future.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/4409c1586a9b3ed20d57ad2faf6c262fc3ccb6e2.1581478568.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The busy timeout for the CMD5 to put the eMMC into sleep state, is specific
to the card. Potentially the timeout may exceed the host->max_busy_timeout.
If that becomes the case, mmc_sleep() converts from using an R1B response
to an R1 response, as to prevent the host from doing HW busy detection.
However, it has turned out that some hosts requires an R1B response no
matter what, so let's respect that via checking MMC_CAP_NEED_RSP_BUSY. Note
that, if the R1B gets enforced, the host becomes fully responsible of
managing the needed busy timeout, in one way or the other.
Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200311092036.16084-1-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The busy timeout that is computed for each erase/trim/discard operation,
can become quite long and may thus exceed the host->max_busy_timeout. If
that becomes the case, mmc_do_erase() converts from using an R1B response
to an R1 response, as to prevent the host from doing HW busy detection.
However, it has turned out that some hosts requires an R1B response no
matter what, so let's respect that via checking MMC_CAP_NEED_RSP_BUSY. Note
that, if the R1B gets enforced, the host becomes fully responsible of
managing the needed busy timeout, in one way or the other.
Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: <stable@vger.kernel.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-By: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It has turned out that some host controllers can't use R1B for CMD6 and
other commands that have R1B associated with them. Therefore invent a new
host cap, MMC_CAP_NEED_RSP_BUSY to let them specify this.
In __mmc_switch(), let's check the flag and use it to prevent R1B responses
from being converted into R1. Note that, this also means that the host are
on its own, when it comes to manage the busy timeout.
Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: <stable@vger.kernel.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-By: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All callers of __mmc_switch() should now be specifying a valid timeout for
the CMD6 command. However, just to be sure, let's print a warning and
default to use the generic_cmd6_time in case the provided timeout_ms
argument is zero.
In this context, let's also simplify some of the corresponding code and
clarify some related comments.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200122142747.5690-4-ulf.hansson@linaro.org
The INAND_CMD38_ARG_EXT_CSD is a vendor specific EXT_CSD register, which is
used to prepare an erase/trim operation. However, it doesn't make sense to
use a timeout of 10 minutes while updating the register, which becomes the
case when the timeout_ms argument for mmc_switch() is set to zero.
Instead, let's use the generic_cmd6_time, as that seems like a reasonable
timeout to use for these cases.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200122142747.5690-3-ulf.hansson@linaro.org
The timeout values used while waiting for a CMD6 for BKOPS or a CACHE_FLUSH
to complete, are not defined by the eMMC spec. However, a timeout of 10
minutes as is currently being used, is just silly for both of these cases.
Instead, let's specify more reasonable timeouts, 120s for BKOPS and 30s for
CACHE_FLUSH.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200122142747.5690-2-ulf.hansson@linaro.org
There are a few places around the code that invert inverted and possibly
inverted CD line. That's really confusing. Squash them all into one place
in mmc_gpiod_request_cd(). MMC_CAP2_CD_ACTIVE_HIGH is used analogously to
WP line: in GPIO mode it is used only at probe time to switch polarity, for
native mode it is left as is.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/db189b715596d63caf8c6a088bddc71dd69a879b.1576031637.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use MMC_CAP2_RO_ACTIVE_HIGH flag as indicator if GPIO line is to be
inverted compared to DT/platform-specified polarity. The flag is not used
after init in GPIO mode anyway. No functional changes intended.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/a60f563f11bbff821da2fa2949ca82922b144860.1576031637.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With large eMMC cards, it is possible to create general purpose
partitions that are bigger than 4GB. The size member of the mmc_part
struct is only an unsigned int which overflows for gp partitions larger
than 4GB. Change this to a u64 to handle the overflow.
Signed-off-by: Bradley Bolen <bradleybolen@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Yann Gautier