Use kobj_to_dev() instead of container_of()
Signed-off-by: Wang Qing <wangqing@vivo.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add a way to lookup a backlight device based on its name.
Will be used by a USB display gadget getting the name from configfs.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
PM8150L WLED supports the following:
- Two modulators and each sink can use any of the modulator
- Multiple CABC selection options from which one can be selected/enabled
- Multiple brightness width selection (12 bits to 15 bits)
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add wled_cabc_config, wled_sync_toggle, wled_ovp_fault_status
and wled_ovp_delay and wled_auto_detection_required callback
functions to prepare the driver for adding WLED5 support.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This converts the l4f00242t03 backlight driver to use GPIO
descriptors and switches the two Freescale i.MX boards over
to passing descriptors instead of global GPIO numbers.
We use the typical names "enable" and "reset" as found in
the device tree bindings for panel GPIOs.
This saves a lot of code in the driver and makes it possible
to get rid of the platform data header altogether.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If probing the LP885x backlight fails after the regulators have been
enabled, then the following warning is seen when releasing the
regulators ...
WARNING: CPU: 1 PID: 289 at drivers/regulator/core.c:2051 _regulator_put.part.28+0x158/0x160
Modules linked in: tegra_xudc lp855x_bl(+) host1x pwm_tegra ip_tables x_tables ipv6 nf_defrag_ipv6
CPU: 1 PID: 289 Comm: systemd-udevd Not tainted 5.6.0-rc2-next-20200224 #1
Hardware name: NVIDIA Jetson TX1 Developer Kit (DT)
...
Call trace:
_regulator_put.part.28+0x158/0x160
regulator_put+0x34/0x50
devm_regulator_release+0x10/0x18
release_nodes+0x12c/0x230
devres_release_all+0x34/0x50
really_probe+0x1c0/0x370
driver_probe_device+0x58/0x100
device_driver_attach+0x6c/0x78
__driver_attach+0xb0/0xf0
bus_for_each_dev+0x68/0xc8
driver_attach+0x20/0x28
bus_add_driver+0x160/0x1f0
driver_register+0x60/0x110
i2c_register_driver+0x40/0x80
lp855x_driver_init+0x20/0x1000 [lp855x_bl]
do_one_initcall+0x58/0x1a0
do_init_module+0x54/0x1d0
load_module+0x1d80/0x21c8
__do_sys_finit_module+0xe8/0x100
__arm64_sys_finit_module+0x18/0x20
el0_svc_common.constprop.3+0xb0/0x168
do_el0_svc+0x20/0x98
el0_sync_handler+0xf4/0x1b0
el0_sync+0x140/0x180
Fix this by ensuring that the regulators are disabled, if enabled, on
probe failure.
Finally, ensure that the vddio regulator is disabled in the driver
remove handler.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- Switch to GPIO descriptor; pwm_bl, corgi_lcd
-----BEGIN PGP SIGNATURE-----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=LJj4
-----END PGP SIGNATURE-----
Merge tag 'backlight-next-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"Switch pwm_bl and corgi_lcd drivers to use GPIO descriptors"
* tag 'backlight-next-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: corgi: Convert to use GPIO descriptors
backlight: pwm_bl: Switch to full GPIO descriptor
The code in the Corgi backlight driver can be considerably
simplified by moving to GPIO descriptors and lookup tables
from the board files instead of passing GPIO numbers using
the old API.
Make sure to encode inversion semantics for the Akita and
Spitz platforms inside the GPIO lookup table and drop the
custom inversion semantics from the driver.
All in-tree users are converted in this patch.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The PWM backlight still supports passing a enable GPIO line as
platform data using the legacy <linux/gpio.h> API.
It turns out that ever board using this mechanism except one
is pass .enable_gpio = -1. So we drop all these cargo-culted -1's
from all instances of this platform data in the kernel.
The remaning board, Palm TC, is converted to pass a machine
descriptior table with the "enable" GPIO instead, and delete the
platform data entry for enable_gpio and the code handling it
and things should work smoothly with the new API.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl5lkYceHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGpHQH/RJrzcaZHo4lw88m
Jf7vBZ9DYUlRgqE0pxTHWmodNObKRqpwOUGflUcWbb/7GD2LQUfeqhSECVQyTID9
N9y7FcPvx321Qhc3EkZ24DBYk0+DQ0K2FVUrSa/PxO0n7czxxXWaLRDmlSULEd3R
D4pVs3zEWOBXJHUAvUQ5R+lKfkeWKNeeepeh+rezuhpdWFBRNz4Jjr5QUJ8od5xI
sIwobYmESJqTRVBHqW8g2T2/yIsFJ78GCXs8DZLe1wxh40UbxdYDTA0NDDTHKzK6
lxzBgcmKzuge+1OVmzxLouNWMnPcjFlVgXWVerpSy3/SIFFkzzUWeMbqm6hKuhOn
wAlcIgI=
=VQUc
-----END PGP SIGNATURE-----
Merge v5.6-rc5 into drm-next
Requested my mripard for some misc patches that need this as a base.
Signed-off-by: Dave Airlie <airlied@redhat.com>
UAPI Changes:
- lima: Add support for heap buffers
Cross-subsystem Changes:
Core Changes:
- Implement mode_config mode_valid for memory constrained drivers
- Bus format negociation between bridges
- Consolidate fake vblank events for drivers without vblank interrupts
- drm/bufs: dma_alloc related cleanups
- drm/dp_mst: Various fixes
- drm/print: New drm_device based print helpers
- Thomas is a drm-misc maintainer now!
Driver Changes:
- DPMS cleanups for atomic drivers
- Removal of owner field in SPI tinydrm drivers
- Removal of explicit dependency on DT for tinydrm drivers
- Conversion to YAML schemas for DT bindings
- tidss: New driver
- virtio: various reworks and fixes
- Our usual dozen or so new panels or bridges
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXkEjOgAKCRDj7w1vZxhR
xeaDAQD+1MludG4RmfQhATe4jTsPC1r2x63OF2CA0ChMGHXJyQEA8qqQ+8y1Cd/u
PZ3PpcTl4qYYHgzJ6FwW7kDPTvlaZQE=
=IJAt
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-02-10' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.7:
UAPI Changes:
- lima: Add support for heap buffers
Cross-subsystem Changes:
Core Changes:
- Implement mode_config mode_valid for memory constrained drivers
- Bus format negociation between bridges
- Consolidate fake vblank events for drivers without vblank interrupts
- drm/bufs: dma_alloc related cleanups
- drm/dp_mst: Various fixes
- drm/print: New drm_device based print helpers
- Thomas is a drm-misc maintainer now!
Driver Changes:
- DPMS cleanups for atomic drivers
- Removal of owner field in SPI tinydrm drivers
- Removal of explicit dependency on DT for tinydrm drivers
- Conversion to YAML schemas for DT bindings
- tidss: New driver
- virtio: various reworks and fixes
- Our usual dozen or so new panels or bridges
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200210093421.xu4sofldm6wm6xq6@gilmour.lan
This patch adds a led-backlight driver (led_bl), which is similar to
pwm_bl except the driver uses a LED class driver to adjust the
brightness in the HW. Multiple LEDs can be used for a single backlight.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes coccicheck warning:
./drivers/video/backlight/qcom-wled.c:1104:5-15:
WARNING: Unsigned expression compared with zero: string_len > 0
The unsigned variable string_len is assigned a return value from the call
to of_property_count_elems_of_size(), which may return negative error code.
Fixes: 775d2ffb4a ("backlight: qcom-wled: Restructure the driver for WLED3")
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Kiran Gunda <kgunda@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jingoo Han <jingoohan1@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191120133838.13132-1-krzk@kernel.org
The Rohm BD6107 driver can pass a fixed GPIO line using the old
GPIO API using platform data. As there are no in-tree users of this
platform data since 2013, we can convert this to use a GPIO descriptor
and require any out-of-tree consumers to pass the GPIO using
a machine descriptor table instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver includes <linux/gpio.h> yet fails to use symbols
from any the header so drop the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is a spelling mistake in a dev_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The probe function in the gpio-backlight driver is quite short. If we
pull gpio_backlight_initial_power_state() into probe we can drop two
more fields from struct gpio_backlight and shrink the driver code.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Instead of dereferencing pdev each time, use a helper variable for
the associated device pointer.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now that the last user of platform data (sh ecovec24) defines a proper
GPIO lookup and sets the 'default-on' device property, we can drop the
platform_data-specific GPIO handling and unify a big chunk of code.
The only field used from the platform data is now the fbdev pointer.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The GPIO backlight driver currently requests the line 'as is', without
acively setting its direction. This can lead to problems: if the line
is in input mode by default, we won't be able to drive it later when
updating the status and also reading its initial value doesn't make
sense for backlight setting.
Request the line 'as is' initially, so that we can read its value
without affecting it but then change the direction to output explicitly
when setting the initial brightness.
Also: check the current direction and only read the value if it's output.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove a double newline from the driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We no longer use any symbols from of_gpio.h. Remove this include.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver should not require a machine specific header. Change
it to pass the GPIO line through a lookup table, and move the
timing generator definitions into the drivers itself.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The auto string detection algorithm checks if the current WLED
sink configuration is valid. It tries enabling every sink and
checks if the OVP fault is observed. Based on this information
it detects and enables the valid sink configuration.
Auto calibration will be triggered when the OVP fault interrupts
are seen frequently thereby it tries to fix the sink configuration.
The auto-detection also kicks in when the connected LED string
of the display-backlight malfunctions (because of damage) and
requires the damaged string to be turned off to prevent the
complete panel and/or board from being damaged.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Handle the short circuit interrupt and check if the short circuit
interrupt is valid. Re-enable the module to check if it goes
away. Disable the module altogether if the short circuit event
persists.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
WLED4 peripheral is present on some PMICs like pmi8998 and
pm660l. It has a different register map and configurations
are also different. Add support for it.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Restructure the driver to add the support for new WLED
peripherals.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Rename the PM8941* references as WLED3 to make the driver
generic and have WLED support for other PMICs. Also rename
"i_boost_limit" and "i_limit" variables to "boost_i_limit"
and "string_i_limit" respectively to resemble the corresponding
register names.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
pm8941-wled.c driver is supporting the WLED peripheral
on pm8941. Rename it to qcom-wled.c so that it can support
WLED on multiple PMICs.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
CONFIG_PREEMPTION is selected by CONFIG_PREEMPT and by CONFIG_PREEMPT_RT.
Both PREEMPT and PREEMPT_RT require the same functionality which today
depends on CONFIG_PREEMPT.
Switch the Kconfig dependency to CONFIG_PREEMPTION.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[Sebastian: +LCD_HP700]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Using a power-of-2 instead of power-of-10 base makes the computations
much cheaper. 2^16 is safe; retval never becomes more than 2^48 +
2^32/2. On a 32 bit platform, the very expensive 64/32 division at the
end of cie1931() instead becomes essentially free (a shift by 32 is
just a register rename).
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
For a fixed small exponent of 3, it is more efficient to simply use
two explicit multiplications rather than calling the int_pow() library
function: Aside from the function call overhead, its implementation
using repeated squaring means it ends up doing four 64x64
multiplications.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
lightness*1000 is nowhere near overflowing 32 bits, so we can just use
an ordinary 32/32 division, which is much cheaper than the 64/32 done
via do_div().
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The "break-even" point for the two formulas is L==8, which is also
what the code actually implements. [Incidentally, at that point one
has Y=0.008856, not 0.08856].
Moreover, all the sources I can find say the linear factor is 903.3
rather than 902.3, which makes sense since then the formulas agree at
L==8, both yielding the 0.008856 figure to four significant digits.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add curly braces to an 'else' branch in pwm_backlight_update_status()
to match the corresponding 'if' branch.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
pwm_backlight_probe() re-assigns pb->levels for every brightness
level. This is not needed and was likely not intended, since
neither side of the assignment changes during the loop. Assign
the field only once.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
For now just enable it in the probe function to allow I2C
access. Disabling also means resetting the register values
to default and according to the datasheet does not give
power savings.
Tested on Kobo Clara HD.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Static structure micro_bl_props, having type backlight_properties, is
used only once, when it is passed as the last argument to function
devm_backlight_device_register(). devm_backlight_device_register() is
defined with its last parameter being declared constant. Hence make
micro_bl_props itself constant as well.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Devicetree aliases are missing, so that module autoloading
does not work properly.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- Obtain scale type through sysfs
- New Functionality
- Provide Device Tree functionality; rave-sp-backlight
- Calculate if scale type is (non-)linear; pwm_bl
- Fix-ups
- Simplify code; lm3630a_bl
- Trivial rename/whitespace/typo fixes; lms283gf05
- Remove superfluous NULL check; tosa_lcd
- Fix power state initialisation; gpio_backlight
- List supported file; MAINTAINERS
- Bug Fixes
- Kconfig - default to not building unless requested; {LED,BACKLIGHT}_CLASS_DEVICE
-----BEGIN PGP SIGNATURE-----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=DSnC
-----END PGP SIGNATURE-----
Merge tag 'backlight-next-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"Core Frameworks
- Obtain scale type through sysfs
New Functionality:
- Provide Device Tree functionality in rave-sp-backlight
- Calculate if scale type is (non-)linear in pwm_bl
Fix-ups:
- Simplify code in lm3630a_bl
- Trivial rename/whitespace/typo fixes in lms283gf05
- Remove superfluous NULL check in tosa_lcd
- Fix power state initialisation in gpio_backlight
- List supported file in MAINTAINERS
Bug Fixes:
- Kconfig - default to not building unless requested in
{LED,BACKLIGHT}_CLASS_DEVICE"
* tag 'backlight-next-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: pwm_bl: Set scale type for brightness curves specified in the DT
backlight: pwm_bl: Set scale type for CIE 1931 curves
backlight: Expose brightness curve type through sysfs
MAINTAINERS: Add entry for stable backlight sysfs ABI documentation
backlight: gpio-backlight: Correct initial power state handling
video: backlight: tosa_lcd: drop check because i2c_unregister_device() is NULL safe
video: backlight: Drop default m for {LCD,BACKLIGHT_CLASS_DEVICE}
backlight: lms283gf05: Fix a typo in the description passed to 'devm_gpio_request_one()'
backlight: lm3630a: Switch to use fwnode_property_count_uXX()
backlight: rave-sp: Leave initial state and register with correct device
Check if a brightness curve specified in the device tree is linear or
not and set the corresponding property accordingly. This makes the
scale type available to userspace via the 'scale' sysfs attribute.
To determine if a curve is linear it is compared to a interpolated linear
curve between min and max brightness. The curve is considered linear if
no value deviates more than +/-5% of ${brightness_range} from their
interpolated value.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
For backlight curves calculated with the CIE 1931 algorithm set
the brightness scale type to non-linear. This makes the scale type
available to userspace via the 'scale' sysfs attribute.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Backlight brightness curves can have different shapes. The two main
types are linear and non-linear curves. The human eye doesn't
perceive linearly increasing/decreasing brightness as linear (see
also 88ba95bedb "backlight: pwm_bl: Compute brightness of LED
linearly to human eye"), hence many backlights use non-linear (often
logarithmic) brightness curves. The type of curve currently is opaque
to userspace, so userspace often uses more or less reliable heuristics
(like the number of brightness levels) to decide whether to treat a
backlight device as linear or non-linear.
Export the type of the brightness curve via the new sysfs attribute
'scale'. The value of the attribute can be 'linear', 'non-linear' or
'unknown'. For devices that don't provide information about the scale
of their brightness curve the value of the 'scale' attribute is 'unknown'.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The default-on property - or the def_value via legacy pdata) should be
handled as:
if it is 1, the backlight must be enabled (kept enabled)
if it is 0, the backlight must be disabled (kept disabled)
This only works for the case when default-on is set. If it is not set then
the brightness of the backlight is set to 0. Now if the backlight is
enabled by external driver (graphics) the backlight will stay disabled since
the brightness is configured as 0. The backlight will not turn on.
In order to minimize screen flickering during device boot:
The initial brightness should be set to 1.
If booted in non DT mode or no phandle link to the backlight node:
follow the def_value/default-on to select UNBLANK or POWERDOWN
If in DT boot we have phandle link then leave the GPIO in a state which the
bootloader left it and let the user of the backlight to configure it
further.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
No need to check the argument of i2c_unregister_device() because the
function itself does it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When running "make oldconfig" on a .config where
CONFIG_BACKLIGHT_LCD_SUPPORT is not set, two new config options
("Lowlevel LCD controls" and "Lowlevel Backlight controls") appear, both
defaulting to "m".
Drop the "default m", as options should default to disabled, and because
several driver config options already select LCD_CLASS_DEVICE or
BACKLIGHT_CLASS_DEVICE when needed.
Fixes: 8c5dc8d9f1 ("video: backlight: Remove useless BACKLIGHT_LCD_SUPPORT kernel symbol")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The description passed to 'devm_gpio_request_one()' should be related to
LMS283GF05, not LMS285GF05.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use use fwnode_property_count_uXX() directly, that makes code neater.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This way the backlight can be referenced through its device node and
enabling/disabling can be managed through the panel driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There was no users left - so drop the code to support EARLY_EVENT_BLANK.
This patch removes the support in backlight,
and drop the notifier in fbmem.
That EARLY_EVENT_BLANK is not used can be verified that no driver set any of:
lcd_ops.early_set_power()
lcd_ops.r_early_set_power()
Noticed while browsing backlight code for other reasons.
v2:
- Fix changelog to say "EARLY_EVENT_BLANK" (Daniel)
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Peter Rosin <peda@axentia.se>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190725143224.GB31803@ravnborg.org
- Provide support for ACPI enumeration; gpio_backlight
- Fix-ups
- SPDX fixups; pwm_bl
- Fix linear brightness levels to include number available; pwm_bl
-----BEGIN PGP SIGNATURE-----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=RKbo
-----END PGP SIGNATURE-----
Merge tag 'backlight-next-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"New Functionality:
- Provide support for ACPI enumeration; gpio_backlight
Fix-ups:
- SPDX fixups; pwm_bl
- Fix linear brightness levels to include number available; pwm_bl"
* tag 'backlight-next-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: pwm_bl: Fix heuristic to determine number of brightness levels
backlight: gpio_backlight: Enable ACPI enumeration
backlight: pwm_bl: Convert to use SPDX identifier
- remove fbdev notifier usage for fbcon (as prep work to clean up the fbcon
locking), add locking checks in vt/console code and make assorted cleanups
in fbdev and backlight code (Daniel Vetter)
- add COMPILE_TEST support to atmel_lcdfb, da8xx-fb, gbefb, imxfb, pvr2fb and
pxa168fb drivers (me)
- fix DMA API abuse in au1200fb and jz4740_fb drivers (Christoph Hellwig)
- add check for new BGRT status field rotation bits in efifb driver (Hans de
Goede)
- mark expected switch fall-throughs in s3c-fb driver (Gustavo A. R. Silva)
- remove fbdev mxsfb driver in favour of the drm version (Fabio Estevam)
- remove broken rfbi code from omap2fb driver (me)
- misc fixes (Arnd Bergmann, Shobhit Kukreti, Wei Yongjun, me)
- misc cleanups (Gustavo A. R. Silva, Colin Ian King, me)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=W1AD
-----END PGP SIGNATURE-----
Merge tag 'fbdev-v5.3' of git://github.com/bzolnier/linux
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
- remove fbdev notifier usage for fbcon (as prep work to clean up the
fbcon locking), add locking checks in vt/console code and make
assorted cleanups in fbdev and backlight code (Daniel Vetter)
- add COMPILE_TEST support to atmel_lcdfb, da8xx-fb, gbefb, imxfb,
pvr2fb and pxa168fb drivers (me)
- fix DMA API abuse in au1200fb and jz4740_fb drivers (Christoph
Hellwig)
- add check for new BGRT status field rotation bits in efifb driver
(Hans de Goede)
- mark expected switch fall-throughs in s3c-fb driver (Gustavo A. R.
Silva)
- remove fbdev mxsfb driver in favour of the drm version (Fabio
Estevam)
- remove broken rfbi code from omap2fb driver (me)
- misc fixes (Arnd Bergmann, Shobhit Kukreti, Wei Yongjun, me)
- misc cleanups (Gustavo A. R. Silva, Colin Ian King, me)
* tag 'fbdev-v5.3' of git://github.com/bzolnier/linux: (62 commits)
video: fbdev: imxfb: fix a typo in imxfb_probe()
video: fbdev: s3c-fb: Mark expected switch fall-throughs
video: fbdev: s3c-fb: fix sparse warnings about using incorrect types
video: fbdev: don't print error message on framebuffer_alloc() failure
video: fbdev: intelfb: return -ENOMEM on framebuffer_alloc() failure
video: fbdev: s3c-fb: return -ENOMEM on framebuffer_alloc() failure
vga_switcheroo: Depend upon fbcon being built-in, if enabled
video: fbdev: omap2: remove rfbi
video: fbdev: atmel_lcdfb: remove redundant initialization to variable ret
video: fbdev-MMP: Use struct_size() in devm_kzalloc()
video: fbdev: controlfb: fix warnings about comparing pointer to 0
efifb: BGRT: Add check for new BGRT status field rotation bits
jz4740_fb: fix DMA API abuse
video: fbdev: pvr2fb: fix link error for pvr2fb_pci_exit
video: fbdev: s3c-fb: add COMPILE_TEST support
video: fbdev: imxfb: fix sparse warnings about using incorrect types
video: fbdev: pvr2fb: fix build warning when compiling as module
fbcon: Export fbcon_update_vcs
backlight: simplify lcd notifier
staging/olpc_dcon: Add drm conversion to TODO
...
With commit 88ba95bedb ("backlight: pwm_bl: Compute brightness of
LED linearly to human eye") the number of set bits (aka hweight())
in the PWM period is used in the heuristic to determine the number
of brightness levels, when the brightness table isn't specified in
the DT. The number of set bits doesn't provide a reliable clue about
the length of the period, instead change the heuristic to:
nlevels = period / fls(period)
Also limit the maximum number of brightness levels to 4096 to avoid
excessively large tables.
With this the number of levels increases monotonically with the PWM
period, until the maximum of 4096 levels is reached:
period (ns) # levels
100 16
500 62
1000 111
5000 416
10000 769
50000 3333
100000 4096
Fixes: 88ba95bedb ("backlight: pwm_bl: Compute brightness of LED linearly to human eye")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
ACPI allows to enumerate specific devices by using compatible strings.
Enable that enumeration for GPIO based backlight devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
While here, correct MODULE_LICENSE() string to be aligned with license text.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With all the work I've done on replacing fb notifier calls with direct
calls into fbcon the backlight/lcd notifier is the only user left.
It will only receive events now that it cares about, hence we can
remove this check.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jingoo Han <jingoohan1@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528090304.9388-34-daniel.vetter@ffwll.ch
Create a new wrapper function for this, feels like there's some
refactoring room here between the two modes.
v2: backlight notifier is also interested in the mode change event,
it calls lcd->set_mode, of which there are 3 implementations. Thanks
to Maarten for spotting this. So we keep that. We can ditch the differentiation
between mode change and all mode changes (because backlight notifier
doesn't care), and we can drop the FBINFO_MISC_USEREVENT stuff too,
because that's just to prevent recursion between fbmem.c and fbcon.c.
While at it flatten the control flow a bit.
v3: Need to add a static inline to the dummy function.
v4: Add missing #include <fbcon.h> to sh_mob (Sam).
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Yisheng Xie <ysxie@foxmail.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Peter Rosin <peda@axentia.se>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: linux-fbdev@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190528090304.9388-29-daniel.vetter@ffwll.ch
This reverts commit 994efacdf9.
The justification is that if hw blanking fails (i.e. fbops->fb_blank)
fails, then we still want to shut down the backlight. Which is exactly
_not_ what fb_blank() does and so rather inconsistent if we end up
with different behaviour between fbcon and direct fbdev usage. Given
that the entire notifier maze is getting in the way anyway I figured
it's simplest to revert this not well justified commit.
v2: Add static inline to the dummy version.
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Yisheng Xie <ysxie@foxmail.com>
Cc: linux-fbdev@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190528090304.9388-25-daniel.vetter@ffwll.ch
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin st fifth floor boston ma 02110
1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 246 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.674189849@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
publishhed by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 48 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.292339952@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
gpl v2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 19 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141333.108140152@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this package is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this package is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this package if not write to the free software foundation inc
51 franklin st fifth floor boston ma 02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.930071175@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version you should have received a copy of the
gnu general public license along with this program if not write to
the free software foundation inc 675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 35 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.655028468@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
licensed under the gpl 2 or later
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 82 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190524100845.150836982@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 or
any later version as published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071859.849348737@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
licensed under the gplv2 or later
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 5 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071859.659568621@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
driver is free software you can redistribute it and or modify it
under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version the [carillo] [ranch] [video]
[subsystem] driver is distributed in the hope that it will be useful
but without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this driver if not
write to the free software foundation inc 51 franklin st fifth floor
boston ma 02110 1301 usa
driver is free software you can redistribute it and or modify it
under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version the [vermilion] [range] [fb] driver is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this driver if not write to the free
software foundation inc 51 franklin st fifth floor boston ma 02110
1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 4 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071858.916314029@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The integer exponentiation is used in few places and might be used in
the future by other call sites. Move it to wider use.
Link: http://lkml.kernel.org/r/20190323172531.80025-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add fwnode support to the lm3630a driver and optionally allow
configuring the label, default brightness level, and maximum brightness
level. The two outputs can be controlled by bank A and B independently
or bank A can control both outputs.
If the platform data was not configured, then the driver defaults to
enabling both banks. This patch changes the default value to disable
both banks before parsing the firmware node so that just a single bank
can be enabled if desired. There are no in-tree users of this driver.
Driver was tested on a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
lm3630a_bank_a_update_status() and lm3630a_bank_b_update_status()
both return the brightness value if the brightness was successfully
updated. Writing to these attributes via sysfs would cause a 'Bad
address' error to be returned. These functions should return 0 on
success, so let's change it to correct that error.
Fixes: 28e64a68a2 ("backlight: lm3630: apply chip revision")
Signed-off-by: Brian Masney <masneyb@onstation.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch removes dependencies on BACKLIGHT_CLASS_DEVICE for items
that are already placed under 'if BACKLIGHT_CLASS_DEVICE'.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We have two *_CLASS_DEVICE kernel config options (LCD_CLASS_DEVICE
and BACKLIGHT_LCD_DEVICE) that do the same job.
The patch removes useless BACKLIGHT_LCD_SUPPORT option
and converts LCD_CLASS_DEVICE into a menu.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
gpiod_get_value() gives out a warning if access to the underlying gpiochip
requires sleeping, which is common for I2C based chips:
WARNING: CPU: 0 PID: 77 at drivers/gpio/gpiolib.c:2500 gpiod_get_value+0xd0/0x100
Modules linked in:
CPU: 0 PID: 77 Comm: kworker/0:2 Not tainted 4.14.0-rc3-00589-gf32897915d48-dirty #90
Hardware name: Allwinner sun4i/sun5i Families
Workqueue: events deferred_probe_work_func
[<c010ec50>] (unwind_backtrace) from [<c010b784>] (show_stack+0x10/0x14)
[<c010b784>] (show_stack) from [<c0797224>] (dump_stack+0x88/0x9c)
[<c0797224>] (dump_stack) from [<c0125b08>] (__warn+0xe8/0x100)
[<c0125b08>] (__warn) from [<c0125bd0>] (warn_slowpath_null+0x20/0x28)
[<c0125bd0>] (warn_slowpath_null) from [<c037069c>] (gpiod_get_value+0xd0/0x100)
[<c037069c>] (gpiod_get_value) from [<c03778d0>] (pwm_backlight_probe+0x238/0x508)
[<c03778d0>] (pwm_backlight_probe) from [<c0411a2c>] (platform_drv_probe+0x50/0xac)
[<c0411a2c>] (platform_drv_probe) from [<c0410224>] (driver_probe_device+0x238/0x2e8)
[<c0410224>] (driver_probe_device) from [<c040e820>] (bus_for_each_drv+0x44/0x94)
[<c040e820>] (bus_for_each_drv) from [<c040ff0c>] (__device_attach+0xb0/0x114)
[<c040ff0c>] (__device_attach) from [<c040f4f8>] (bus_probe_device+0x84/0x8c)
[<c040f4f8>] (bus_probe_device) from [<c040f944>] (deferred_probe_work_func+0x50/0x14c)
[<c040f944>] (deferred_probe_work_func) from [<c013be84>] (process_one_work+0x1ec/0x414)
[<c013be84>] (process_one_work) from [<c013ce5c>] (worker_thread+0x2b0/0x5a0)
[<c013ce5c>] (worker_thread) from [<c0141908>] (kthread+0x14c/0x154)
[<c0141908>] (kthread) from [<c0107ab0>] (ret_from_fork+0x14/0x24)
This was missed in commit 0c9501f823 ("backlight: pwm_bl: Handle gpio
that can sleep"). The code was then moved to a separate function in
commit 7613c92231 ("backlight: pwm_bl: Move the checks for initial power
state to a separate function").
The only usage of gpiod_get_value() is during the probe stage, which is
safe to sleep in. Switch to gpiod_get_value_cansleep().
Fixes: 0c9501f823 ("backlight: pwm_bl: Handle gpio that can sleep")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull Devicetree updates from Rob Herring:
"The biggest highlight here is the start of using json-schema for DT
bindings. Being able to validate bindings has been discussed for years
with little progress.
- Initial support for DT bindings using json-schema language. This is
the start of converting DT bindings from free-form text to a
structured format.
- Reworking of initrd address initialization. This moves to using the
phys address instead of virt addr in the DT parsing code. This
rework was motivated by CONFIG_DEV_BLK_INITRD causing unnecessary
rebuilding of lots of files.
- Fix stale phandle entries in phandle cache
- DT overlay validation improvements. This exposed several memory
leak bugs which have been fixed.
- Use node name and device_type helper functions in DT code
- Last remaining conversions to using %pOFn printk specifier instead
of device_node.name directly
- Create new common RTC binding doc and move all trivial RTC devices
out of trivial-devices.txt.
- New bindings for Freescale MAG3110 magnetometer, Cadence Sierra
PHY, and Xen shared memory
- Update dtc to upstream version v1.4.7-57-gf267e674d145"
* tag 'devicetree-for-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (68 commits)
of: __of_detach_node() - remove node from phandle cache
of: of_node_get()/of_node_put() nodes held in phandle cache
gpio-omap.txt: add reg and interrupts properties
dt-bindings: mrvl,intc: fix a trivial typo
dt-bindings: iio: magnetometer: add dt-bindings for freescale mag3110
dt-bindings: Convert trivial-devices.txt to json-schema
dt-bindings: arm: mrvl: amend Browstone compatible string
dt-bindings: arm: Convert Tegra board/soc bindings to json-schema
dt-bindings: arm: Convert ZTE board/soc bindings to json-schema
dt-bindings: arm: Add missing Xilinx boards
dt-bindings: arm: Convert Xilinx board/soc bindings to json-schema
dt-bindings: arm: Convert VIA board/soc bindings to json-schema
dt-bindings: arm: Convert ST STi board/soc bindings to json-schema
dt-bindings: arm: Convert SPEAr board/soc bindings to json-schema
dt-bindings: arm: Convert CSR SiRF board/soc bindings to json-schema
dt-bindings: arm: Convert QCom board/soc bindings to json-schema
dt-bindings: arm: Convert TI nspire board/soc bindings to json-schema
dt-bindings: arm: Convert TI davinci board/soc bindings to json-schema
dt-bindings: arm: Convert Calxeda board/soc bindings to json-schema
dt-bindings: arm: Convert Altera board/soc bindings to json-schema
...
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
For instances using of_node_cmp, this has the side effect of now using
case sensitive comparisons. This should not matter for any FDT based
system which this is.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit '88ba95bedb79 ("backlight: pwm_bl: Compute brightness of LED
linearly to human eye")' allows the possibility to compute a default
brightness table when there isn't the brightness-levels property in the
DT. Unfortunately the changes made broke the pwm backlight for the
non-DT boards.
Usually, the non-DT boards don't pass the brightness levels via platform
data, instead, it sets the max_brightness in their platform data and the
driver calculates the level without a table. The offending patch assumed
that when there is no brightness levels table we should create one, but this
is clearly wrong for the non-DT case.
After this patch the code handles the DT and the non-DT case taking in
consideration also if max_brightness is set or not.
Fixes: 88ba95bedb ("backlight: pwm_bl: Compute brightness of LED linearly to human eye")
Reported-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Commit 88ba95bedb ("backlight: pwm_bl: Compute brightness of LED linearly
to human eye") made the parse-dt function return early when using an auto-
generated brightness-table, but didn't take into account that some more
settings were handled below the brightness handling, like power-on-delays
and also setting the pdata enable-gpio to -EINVAL.
This surfaces for example in the case of a backlight without any
enable-gpio which then tries to use gpio-0 in error.
Fix this by simply moving the trailing settings above the brightness
handling.
Fixes: 88ba95bedb ("backlight: pwm_bl: Compute brightness of LED linearly to human eye")
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit e6bcca0890 ("backlight: pwm_bl: Switch to using "atomic" PWM API")
removed the driver internal enabled tracking in favor of simply checking
the pwm state.
This can lead to issues as all of gpio-, regulator- and pwm-state are used
to determine the initial state and the bootloader or kernel can leave them
in an inconsistent state at boot.
In my case on rk3399-kevin, the pwm backlight is build as module and the
kernel disables the supply regulator as unused while keeping the pwm running
thus pwm_bl calling pwm_backlight_power_off() during probe and creating an
unmatched regulator-disable call, as it never got enabled from the pwm-bl
before.
To prevent these consistency issues, reintroduce the driver-internal
tracking of the enabled state.
Fixes: e6bcca0890 ("backlight: pwm_bl: Switch to using "atomic" PWM API")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
-----BEGIN PGP SIGNATURE-----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=Cc6D
-----END PGP SIGNATURE-----
Merge tag 'media/v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new dvb frontend driver: lnbh29
- new sensor drivers: imx319 and imx 355
- some old soc_camera driver renames to avoid conflict with new
drivers
- new i.MX Pixel Pipeline (PXP) mem-to-mem platform driver
- a new V4L2 frontend for the FWHT codec
- several other improvements, bug fixes, code cleanups, etc
* tag 'media/v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (289 commits)
media: rename soc_camera I2C drivers
media: cec: forgot to cancel delayed work
media: vivid: Support 480p for webcam capture
media: v4l2-tpg: fix kernel oops when enabling HFLIP and OSD
media: vivid: Add 16-bit bayer to format list
media: v4l2-tpg-core: Add 16-bit bayer
media: pvrusb2: replace `printk` with `pr_*`
media: venus: vdec: fix decoded data size
media: cx231xx: fix potential sign-extension overflow on large shift
media: dt-bindings: media: rcar_vin: add device tree support for r8a7744
media: isif: fix a NULL pointer dereference bug
media: exynos4-is: make const array config_ids static
media: cx23885: make const array addr_list static
media: ivtv: make const array addr_list static
media: bttv-input: make const array addr_list static
media: cx18: Don't check for address of video_dev
media: dw9807-vcm: Fix probe error handling
media: dw9714: Remove useless error message
media: dw9714: Fix error handling in probe function
media: cec: name for RC passthrough device does not need 'RC for'
...
The driver for LD9040 AMOLED LCD panel was superseded with DRM driver
panel-samsung-ld9040.c. It does not support DeviceTree and respective
possible user (Exynos4210 Universal C210) is DeviceTree-only and uses
DRM version of driver.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver for S6E63M0 AMOLED LCD panel is not used. It does not
support DeviceTree and respective possible users (S5Pv210 Aquila and
Goni boards) are DeviceTree-only.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Clang warns that the address of a pointer will always evaluated as true
in a boolean context.
drivers/video/backlight/lm3639_bl.c:403:14: warning: address of
'pchip->cdev_torch' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (&pchip->cdev_torch)
~~ ~~~~~~~^~~~~~~~~~
drivers/video/backlight/lm3639_bl.c:405:14: warning: address of
'pchip->cdev_flash' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (&pchip->cdev_flash)
~~ ~~~~~~~^~~~~~~~~~
2 warnings generated.
These statements have been present since 2012, introduced by
commit 0f59858d51 ("backlight: add new lm3639 backlight
driver"). Given that they have been called unconditionally since
then presumably without any issues, removing the always true if
statements to fix the warnings without any real world changes.
Link: https://github.com/ClangBuiltLinux/linux/issues/119
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The "atomic" API allows us to configure PWM period and duty_cycle and
enable it in one call.
The patch also moves the pwm_init_state just before any use of the
pwm_state struct, this fixes a potential bug where pwm_get_state
can be called before pwm_init_state.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
As original license mentioned, it is GPL-2.0 in SPDX.
Then, MODULE_LICENSE() should be "GPL v2" instead of "GPL".
See ${LINUX}/include/linux/module.h
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
No functional changes
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently, if the DT does not define num-interpolated-steps then
num_steps is undefined and the interpolation code will deploy randomly.
Fix with a simple initialize to zero.
Fixes: 573fe6d1c2 ("backlight: pwm_bl: Linear interpolation between brightness-levels")
Reported-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When you want to change the brightness using a PWM signal, one thing you
need to consider is how human perceive the brightness. Human perceive
the brightness change non-linearly, we have better sensitivity at low
luminance than high luminance, so to achieve perceived linear dimming,
the brightness must be matches to the way our eyes behave. The CIE 1931
lightness formula is what actually describes how we perceive light.
This patch computes a default table with the brightness levels filled
with the numbers provided by the CIE 1931 algorithm, the number of the
brightness levels is calculated based on the PWM resolution.
The calculation of the table using the CIE 1931 algorithm is enabled by
default when you do not define the 'brightness-levels' propriety in your
device tree.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Setting num-interpolated-steps in the dts will allow you to have linear
interpolation between values of brightness-levels. This way a high
resolution pwm duty cycle can be used without having to list out every
possible value in the dts. This system also allows for gamma corrected
values.
The most simple example is interpolate between two brightness values a
number of steps, this can be done setting the following in the dts:
brightness-levels = <0 65535>;
num-interpolated-steps = <1024>;
default-brightness-level = <512>;
This will create a brightness-level table with the following values:
<0 63 126 189 252 315 378 441 ... 64260 64323 64386 64449 65535>
Another use case can be describe a gamma corrected curve, as we have
better sensitivity at low luminance than high luminance we probably
want have smaller steps for low brightness levels values and bigger
steps for high brightness levels values. This can be achieved with
the following in the dts:
brightness-levels = <0 4096 65535>;
num-interpolated-steps = <1024>;
default-brightness-level = <512>;
This will create a brightness-levels table with the following values:
<0 4 8 12 16 20 ... 4096 4156 4216 4276 ... 65535>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Two framebuffer device-node names were looked up during probe, but were
only used as flags to indicate the presence of two framebuffer device.
Drop the unused framebuffer name along with a likewise unused device
pointer from the driver data, and update the platform data to pass in
booleans instead of the framebuffer strings. This allows us do drop the
node references acquired during probe, which would otherwise leak.
Note that there are no other in-kernel users of the modified
platform-data fields.
Fixes: 59eb2b5e57 ("drivers/video/backlight/as3711_bl.c: add OF support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
This would only cause trouble if the child node is missing while there
is an unrelated node named "backlight" elsewhere in the tree.
Cc: stable <stable@vger.kernel.org> # 3.7
Fixes: eebfdc17cc ("backlight: Add TPS65217 WLED driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent mfd node was also prematurely freed,
while the child backlight node was leaked.
Cc: stable <stable@vger.kernel.org> # 3.9
Fixes: 47ec340cb8 ("mfd: max8925: Support dt for backlight")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent mfd node was also prematurely freed.
Cc: stable <stable@vger.kernel.org> # 3.10
Fixes: 59eb2b5e57 ("drivers/video/backlight/as3711_bl.c: add OF support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Leaking driver internal tracking into the already massively confusing
backlight power tracking is really confusing.
Stop that by allocating a tiny driver private data structure instead.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Nothing in the entire tree ever sets this, which means this is dead
code. Remove it.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds a LCD driver supporting the OTM3225A LCD SoC
from ORISE Technology. This device can drive TFT LC panels having a
resolution of 240x320 pixels. After initializing the OTM3225A using
it's SPI interface it switches to use 16-bib RGB as external
display interface.
Signed-off-by: Felix Brack <fb@ltec.ch>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The documentation was wrong, gpiod_get_direction() returns 0/1 instead
of the GPIOF_* flags. The docs were fixed with commit 94fc73094a
("gpio: correct docs about return value of gpiod_get_direction"). Now,
fix this user (until a better, system-wide solution is in place).
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some panels (i.e. N116BGE-L41), in their power sequence specifications,
request a delay between set the PWM signal and enable the backlight and
between clear the PWM signal and disable the backlight. Add support for
the new post-pwm-on-delay-ms and pwm-off-delay-ms proprieties to meet
the timings.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Before this patch the enable signal was set before the PWM signal and
vice-versa on power off. This sequence is wrong, at least, it is on
the different panels datasheets that I checked, so I inverted the sequence
to follow the specs.
For reference the following panels have the mentioned sequence:
- N133HSE-EA1 (Innolux)
- N116BGE (Innolux)
- N156BGE-L21 (Innolux)
- B101EAN0 (Auo)
- B101AW03 (Auo)
- LTN101NT05 (Samsung)
- CLAA101WA01A (Chunghwa)
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This driver provides access to RAVE SP backlight control
functionality.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
migrate the backlight helpers from tinydrm to the backlight subsystem.
https://patchwork.freedesktop.org/series/36522/
Cc: Meghana Madhyastha <meghana.madhyastha@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAlpvdTQACgkQlvcN/ahK
Bwp5Pgf8Cfn7p7/HV5npF0b0NZ3w0FLF+AjggxKdKBNsVYdO1qGrhfQJviuMRj7c
cqm+SQ4OFJEwGMqVGsZLgRkyVrbCma/OZEcipJiSGHLG9owDgVFYTQ4bnakmdt1m
QYJTETNxoNJ1EHCG1tfr9/jDR3GPL3OnSUOWnlTXDzpJ2PCw4BB0uArqG+pgmyhJ
DCMdvYkQ+5tYB814otnN3zklklQITNGww8LTJMtDFyJVIz2RZHioq5JqXD48UfMb
haDVbiYsOamw+eP4z5uyfCi1rKwzpPhas9IpeDn5gY6rEp/t+GTkSr0JHUEs/iB+
+eAH076eTp3M8iv7YF67XYLZQeDuwQ==
=azAl
-----END PGP SIGNATURE-----
Merge tag 'topic/backlight_for_lag-2018-01-29' of git://anongit.freedesktop.org/drm/drm-misc into drm-misc-next
This contains the backlight portion of Meghana Madhyastha's patch set to
migrate the backlight helpers from tinydrm to the backlight subsystem.
https://patchwork.freedesktop.org/series/36522/
Cc: Meghana Madhyastha <meghana.madhyastha@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
# gpg: Signature made Mon 29 Jan 2018 02:25:40 PM EST
# gpg: using RSA key 7F17297CC4A076740CB3E42A96F70DFDA84A070A
# gpg: Good signature from "Sean Paul <seanpaul@chromium.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 1C5E AB9E D7C9 DDE9 E7F2 087C 732C 0025 72DC AF79
# Subkey fingerprint: 7F17 297C C4A0 7674 0CB3 E42A 96F7 0DFD A84A 070A
Link: https://patchwork.freedesktop.org/patch/msgid/20180129192950.bvmhkz3h42t5a25r@art_vandelay
Add devm_of_find_backlight and the corresponding release
function because some drivers use devres versions of functions
for acquiring device resources.
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Meghana Madhyastha <meghana.madhyastha@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/021f8fecfa3f374dc5dcb70fb07a6f6b019bea7b.1516810725.git.meghana.madhyastha@gmail.com
Add of_find_backlight, a helper function which is a generic version
of tinydrm_of_find_backlight that can be used by other drivers to avoid
repetition of code and simplify things.
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Meghana Madhyastha <meghana.madhyastha@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/116d160ba78be2e6dcbdcb6855622bce67da9472.1516810725.git.meghana.madhyastha@gmail.com
Currently the LCD display (TD035S) on the cm-x300 platform is broken and
remains blank.
The TD0245S specification requires that the chipselect is toggled
between commands sent to the panel. This was also the purpose of the
former patch of commit f64dcac0b1 ("backlight: tdo24m: ensure chip
select changes between transfers").
Unfortunately, the "cs_change" field of a SPI transfer is
misleading. Its true meaning is that for a SPI message holding multiple
transfers, the chip select is toggled between each transfer, but for the
last transfer it remains asserted.
In this driver, all the SPI messages contain exactly one transfer, which
means that each transfer is the last of its message, and as a
consequence the chip select is never toggled.
Actually, there was a second bug hidding the first one, hence the
problem was not seen until v4.6. This problem was fixed by commit
a52db659c7 ("spi: pxa2xx: Fix cs_change management") for PXA based
boards.
This fix makes the TD035S work again on a cm-x300 board. The same
applies to other PXA boards, ie. corgi and tosa.
Fixes: a52db659c7 ("spi: pxa2xx: Fix cs_change management")
Reported-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
pci_get_bus_and_slot() is restrictive such that it assumes domain=0 as
where a PCI device is present. This restricts the device drivers to be
reused for other domain numbers.
Getting ready to remove pci_get_bus_and_slot() function in favor of
pci_get_domain_bus_and_slot().
Hard-coding the domain as 0.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The variable len is assigned but never read, therefore it is redundant
and can be removed. Cleans up clang warning:
drivers/video/backlight/ili922x.c:276:2: warning: Value stored to 'len'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the driver boots only via device tree hence add a
dependency on CONFIG_OF. This leaves with a bunch of unused code
so clean that up. This patch also makes use of probe_new function
in place of the probe function so as to avoid passing i2c_device_id.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Variable val holds the default brightness and is unsigned, therefore
checking whether it is less than zero is redundant.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This fixes an overflow condition that can happen with high max
brightness and period values in compute_duty_cycle. This fixes it by
using a 64 bit variable for computing the duty cycle.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The option to invert the output of the GPIO (active low) is
not used by the only platform still using platform data to
set up a GPIO backlight (one SH board). Delete the option
as we do not expect to expand the use of board files for
this driver, and GPIO descriptors intrinsically keep track
of any signal inversion.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This driver is predominantly used by device tree systems, all
of which can deal with modern GPIO descriptors. The legacy
GPIO API is only used by one SH board so make the GPIO
descriptor the default way to deal with it.
As an intended side effect we do not need to look around in
the device tree for the inversion flag since the GPIO
descriptors will intrinsically deal with this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In the lm3630a_chip_init we try to write to 0x50 register, which is
higher value then the max_register value, this resulted in regmap_write
return -EIO.
Fix this by bumping REG_MAX value to 0x50.
This code was introduced with the chip revision in commit 28e64a68a2,
however setting filter strength was failing silently because it used
unsigned int for storing and comparing the return values. Bug related to
signedness was fixed in 2a0c316bf3, which made it error out correctly
instead of failing silently.
I found this issue by using this driver on LGE Nexus 5 (hammerhead).
After this commit lm3630a_chip_init succeeds instead of failing with
-EIO.
Fixes: 28e64a68a2 ("backlight: lm3630: apply chip revision")
Fixes: 2a0c316bf3 ("drivers/video/backlight/lm3630a_bl.c: fix
signedness bug in lm3630a_chip_init()")
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bhushan Shah <bshah@kde.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
include/linux/i2c is not for client devices.
Move the header file to a more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is possible to update the backlight power and the brightness using
the sysfs and on writing it either returns the count or if the callback
function does not exist then returns the error code 'ENXIO'.
We have a situation where the userspace client is writing to the sysfs
to update the power and since the callback function exists the client
receives the return value as count and considers the operation to be
successful. That is correct as the write to the sysfs was successful.
But there is no way to know if the actual operation was done or not.
backlight_update_status() returns the error code if it fails. Pass that
to the userspace client who is trying to update the power so that the
client knows that the operation failed.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This driver provides support for the Arctic Sand arc2c0608 chip,
and provides a framework to support future devices.
Signed-off-by: Olimpiu Dejeu <olimpiu@arcticsand.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 7613c92231 ("backlight: pwm_bl: Move the checks for initial
power state to a separate function") not just moved some code, but made
slight changes in semantics.
If a gpiochip doesn't implement the optional .get_direction() callback,
gpiod_get_direction always returns -EINVAL, which is never equal to
GPIOF_DIR_IN, leading to the GPIO not being configured for output.
To avoid this, invert the test and check for not GPIOF_DIR_OUT instead,
like the original code did.
This restores the display on r8a7740/armadillo.
Fixes: 7613c92231 ("backlight: pwm_bl: Move the checks for initial power state to a separate function")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
The driver has a platform device ID table with multiple device entries,
each setting a different register address in its driver_data to control
the WLED brightness.
But the driver doesn't export these as aliases with MODULE_DEVICE_TABLE()
when the driver is built as a module, instead it just has a single alias
using MODULE_ALIAS("platform:da9052-backlight"). That is clearly wrong
since there isn't a "da9052-backlight" in the platform device ID table,
so if that device name is used, the device won't even match the driver.
So instead of having a wrong alias, export the ones in the dev ID table.
Before this patch:
$ modinfo drivers/video/backlight/da9052_bl.ko | grep alias
alias: platform:da9052-backlight
After this patch:
$ modinfo drivers/video/backlight/da9052_bl.ko | grep alias
alias: platform:da9052-wled3
alias: platform:da9052-wled2
alias: platform:da9052-wled1
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If the PWM is not enabled the backlight initially should not be enabled
either if we have booted with DT and there is a phandle pointing to the
backlight node.
The patch extends the checks to decide if we should keep the backlight off
initially.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move the checks to select the initial state for the backlight to a new
function and document the checks we are doing.
With the separate function it is going to be easier to fix or improve the
initial power state configuration later and it is easier to read the code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If adp5520_bl_setup() fails, sysfs group left unremoved.
By the way, fix overcomplicated assignement of error code.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Once device_register is called for a device its attributes might be
accessed. As the callbacks of a lcd device's attributes make use of the
lcd_ops, the respective member must be setup before calling
device_register.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some backlight GPIOs might be connected to some i2c based expanders whose
access might sleep.
Since it's not in any critical path, use the cansleep variant of the GPIO
API.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The field "owner" is set by the core.
Thus delete an unneeded initialisation.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The LP8556 datasheet describes an EN/VDDIO input, which serves "both as
a chip enable and as a power supply reference for PWM, SDA, and SCL
inputs." The LP8556 that I'm testing doesn't respond properly if I try
to talk I2C to it too quickly after enabling VDDIO, and the LP8555
datasheet mentions a t_RESPONSE delay of up to 1 millisecond.
Support this EN/VDDIO by adding a regulator property to the binding;
enabling this regulator at probe time; and sleeping for 1 to 2ms, if the
EN/VDDIO regulator was provided.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Milo Kim <milo.kim@ti.com>
Reviewed-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This set of changes introduces an atomic API to the PWM subsystem. This
is influenced by the DRM atomic API that was introduced a while back,
though it is obviously a lot simpler. The fundamental idea remains the
same, though: drivers provide a single callback to implement the atomic
configuration of a PWM channel.
As a side-effect the PWM subsystem gains the ability for initial state
retrieval, so that the logical state mirrors that of the hardware. Many
use-cases don't care about this, but for others it is essential.
These new features require changes in all users, which these patches
take care of. The core is transitioned to use the atomic callback if
available and provides a fallback mechanism for other drivers.
Changes to transition users and drivers to the atomic API are postponed
to v4.8.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sxT9
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes introduces an atomic API to the PWM subsystem.
This is influenced by the DRM atomic API that was introduced a while
back, though it is obviously a lot simpler. The fundamental idea
remains the same, though: drivers provide a single callback to
implement the atomic configuration of a PWM channel.
As a side-effect the PWM subsystem gains the ability for initial state
retrieval, so that the logical state mirrors that of the hardware.
Many use-cases don't care about this, but for others it is essential.
These new features require changes in all users, which these patches
take care of. The core is transitioned to use the atomic callback if
available and provides a fallback mechanism for other drivers.
Changes to transition users and drivers to the atomic API are
postponed to v4.8"
* tag 'pwm/for-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (30 commits)
pwm: Add information about polarity, duty cycle and period to debugfs
pwm: Switch to the atomic API
pwm: Update documentation
pwm: Add core infrastructure to allow atomic updates
pwm: Add hardware readout infrastructure
pwm: Move the enabled/disabled info into pwm_state
pwm: Introduce the pwm_state concept
pwm: Keep PWM state in sync with hardware state
ARM: Explicitly apply PWM config extracted from pwm_args
drm: i915: Explicitly apply PWM config extracted from pwm_args
input: misc: pwm-beeper: Explicitly apply PWM config extracted from pwm_args
input: misc: max8997: Explicitly apply PWM config extracted from pwm_args
backlight: lm3630a: explicitly apply PWM config extracted from pwm_args
backlight: lp855x: Explicitly apply PWM config extracted from pwm_args
backlight: lp8788: Explicitly apply PWM config extracted from pwm_args
backlight: pwm_bl: Use pwm_get_args() where appropriate
fbdev: ssd1307fb: Use pwm_get_args() where appropriate
regulator: pwm: Use pwm_get_args() where appropriate
leds: pwm: Use pwm_get_args() where appropriate
input: misc: max77693: Use pwm_get_args() where appropriate
...
Call pwm_apply_args() just after requesting the PWM device so that the
polarity and period are initialized according to the information
provided in pwm_args.
This is an intermediate state, and pwm_apply_args() should be dropped as
soon as the atomic PWM infrastructure is in place and the driver makes
use of it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Call pwm_apply_args() just after requesting the PWM device so that the
polarity and period are initialized according to the information
provided in pwm_args.
This is an intermediate state, and pwm_apply_args() should be dropped as
soon as the atomic PWM infrastructure is in place and the driver makes
use of it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Call pwm_apply_args() just after requesting the PWM device so that the
polarity and period are initialized according to the information
provided in pwm_args.
This is an intermediate state, and pwm_apply_args() should be dropped as
soon as the atomic PWM infrastructure is in place and the driver makes
use of it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The PWM framework has clarified the concept of reference PWM config (the
platform dependent config retrieved from the DT or the PWM lookup table)
and real PWM state.
Use pwm_get_args() when the PWM user wants to retrieve this reference
config and not the current state.
This is part of the rework allowing the PWM framework to support
hardware readout and expose real PWM state even when the PWM has just
been requested (before the user calls pwm_config/enable/disable()).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwm->period field is not supposed to be changed by PWM users. The only
ones authorized to change it are the PWM core and PWM drivers.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The PWM period will be set when calling pwm_config. Remove this useless
call to pwm_set_period(), which might mess up the internal PWM state.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Wang Qing