According to SMBIOSv3 specification the length of DMI table can be
up to 32bits wide. So use appropriate type to avoid overflow.
It's obvious that dmi_num theoretically can be more than u16 also,
so it's can be changed to u32 or at least it's better to use int
instead of u16, but on that moment I cannot imagine dmi structure
count more than 65535 and it can require changing type of vars that
work with it. So I didn't correct it.
Acked-by: Ard Biesheuvel <ard@linaro.org>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
The dmi-sysfs should create "End of Table" entry, that is type 127. But
after adding initial SMBIOS v3 support fc43026278 ("dmi: add support
for SMBIOS 3.0 64-bit entry point") the 127-0 entry is not handled any
more, as result it's not created in dmi sysfs for instance. This is
important because the size of whole DMI table must correspond to sum of
all DMI entry sizes.
So move the end-of-table check after it's handled by dmi_table.
Reviewed-by: Ard Biesheuvel <ard@linaro.org>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Cc: <stable@vger.kernel.org> # v3.19
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
The DMTF SMBIOS reference spec v3.0.0 defines a new 64-bit entry point,
which enables support for SMBIOS structure tables residing at a physical
offset over 4 GB. This is especially important for upcoming arm64
platforms whose system RAM resides entirely above the 4 GB boundary.
For the UEFI case, this code attempts to detect the new SMBIOS 3.0
header magic at the offset passed in the SMBIOS3_TABLE_GUID UEFI
configuration table. If this configuration table is not provided, or
if we fail to parse the header, we fall back to using the legacy
SMBIOS_TABLE_GUID configuration table. This is in line with the spec,
that allows both configuration tables to be provided, but mandates that
they must point to the same structure table, unless the version pointed
to by the 64-bit entry point is a superset of the 32-bit one.
For the non-UEFI case, the detection logic is modified to look for the
SMBIOS 3.0 header magic before it looks for the legacy header magic.
Note that this patch is based on version 3.0.0d [draft] of the
specification, which is expected not to deviate from the final version
in ways that would affect the correctness of this implementation.
Tested-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Acked-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Tony Luck <tony.luck@intel.com>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
This patch makes a couple of changes to the SMBIOS/DMI scanning
code so it can be used on other archs (such as ARM and arm64):
(a) wrap the calls to ioremap()/iounmap(), this allows the use of a
flavor of ioremap() more suitable for random unaligned access;
(b) allow the non-EFI fallback probe into hardcoded physical address
0xF0000 to be disabled.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Firmware is not required to maintain alignment of SMBIOS
entries, so we should take care accessing fields within these
structures. Use "get_unaligned()" to avoid problems.
[ Found on ia64 (which grumbles about unaligned access) ]
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Chen Gong <gong.chen@linux.intel.com>
Link: http://lkml.kernel.org/r/27d82dbff5be1025bf18ab88498632d36c2fcf3c.1383331440.git.tony.luck@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds a new interface to decode memory device (type 17)
to help error reporting on DIMMs.
Original-author: Tony Luck <tony.luck@intel.com>
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
As reported by Joe Perches: OOM messages generally aren't useful.
dmi_alloc is either a trivial front-end to kzalloc, and kzalloc already
does a dump_stack() when OOM, or for x86, dmi_alloc uses extend_brk
which BUGs when unsuccessful.
So we can remove all 6 such log messages in the dmi_scan driver, to
shrink the binary size (by 528 bytes on x86_64.)
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reported-by: Joe Perches <joe@perches.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add const to all DMI string pointers where this is possible. This fixes a
checkpatch warning.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Joe Perches <joe@perches.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix all errors and trivial warnings reported by checkpatch for file
drivers/firmware/dmi_scan.c.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Joe Perches <joe@perches.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This comment predates the introduction of early_ioremap. Since then the
missing calls to dmi_iounmap have been added by Ingo and Yinghai in
commits 0d64484f7e ("x86: fix DMI ioremap leak") and 3212bff370
("x86: left over fix for leak of early_ioremp in dmi_scan") . That was
over 5 years ago so it is about time to drop this now misleading
comment.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Joe Perches <joe@perches.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
My previous refactoring in commit 79bae42d51 ("dmi_scan: refactor
dmi_scan_machine(), {smbios,dmi}_present()") resulted in slightly tricky
code (though I think it's more elegant). Explain what it's doing.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dmi_match() considers a substring match to be a successful match. This is
not always sufficient to distinguish between DMI data for different
systems. Add support for exact string matching using strcmp() in addition
to the substring matching using strstr().
The specific use case in the i915 driver is to allow us to use an exact
match for D510MO, without also incorrectly matching D510MOV:
{
.ident = "Intel D510MO",
.matches = {
DMI_MATCH(DMI_BOARD_VENDOR, "Intel"),
DMI_EXACT_MATCH(DMI_BOARD_NAME, "D510MO"),
},
}
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: <annndddrr@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Cornel Panceac <cpanceac@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the calls to memcpy_fromio() up into the loop in
dmi_scan_machine(), and move the signature checks back down into
dmi_decode(). We need to check at 16-byte intervals but keep a 32-byte
buffer for an SMBIOS entry, so shift the buffer after each iteration.
Merge smbios_present() into dmi_present(), so we look for an SMBIOS
signature at the beginning of the given buffer and then for a DMI
signature at an offset of 16 bytes.
[artem.savkov@gmail.com: use proper buf type in dmi_present()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Reported-by: Tim McGrath <tmhikaru@gmail.com>
Tested-by: Tim Mcgrath <tmhikaru@gmail.com>
Cc: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Signed-off-by: Artem Savkov <artem.savkov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
x86 and ia64 can acquire extra hardware identification information
from DMI and print it along with task dumps; however, the usage isn't
consistent.
* x86 show_regs() collects vendor, product and board strings and print
them out with PID, comm and utsname. Some of the information is
printed again later in the same dump.
* warn_slowpath_common() explicitly accesses the DMI board and prints
it out with "Hardware name:" label. This applies to both x86 and
ia64 but is irrelevant on all other archs.
* ia64 doesn't show DMI information on other non-WARN dumps.
This patch introduces arch-specific hardware description used by
dump_stack(). It can be set by calling dump_stack_set_arch_desc()
during boot and, if exists, printed out in a separate line with
"Hardware name:" label.
dmi_set_dump_stack_arch_desc() is added which sets arch-specific
description from DMI data. It uses dmi_ids_string[] which is set from
dmi_present() used for DMI debug message. It is superset of the
information x86 show_regs() is using. The function is called from x86
and ia64 boot code right after dmi_scan_machine().
This makes the explicit DMI handling in warn_slowpath_common()
unnecessary. Removed.
show_regs() isn't yet converted to use generic debug information
printing and this patch doesn't remove the duplicate DMI handling in
x86 show_regs(). The next patch will unify show_regs() handling and
remove the duplication.
An example WARN dump follows.
WARNING: at kernel/workqueue.c:4841 init_workqueues+0x35/0x505()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.9.0-rc1-work+ #3
Hardware name: empty empty/S3992, BIOS 080011 10/26/2007
0000000000000009 ffff88007c861e08 ffffffff81c614dc ffff88007c861e48
ffffffff8108f500 ffffffff82228240 0000000000000040 ffffffff8234a08e
0000000000000000 0000000000000000 0000000000000000 ffff88007c861e58
Call Trace:
[<ffffffff81c614dc>] dump_stack+0x19/0x1b
[<ffffffff8108f500>] warn_slowpath_common+0x70/0xa0
[<ffffffff8108f54a>] warn_slowpath_null+0x1a/0x20
[<ffffffff8234a0c3>] init_workqueues+0x35/0x505
...
v2: Use the same string as the debug message from dmi_present() which
also contains BIOS information. Move hardware name into its own
line as warn_slowpath_common() did. This change was suggested by
Bjorn Helgaas.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We're goning to use DMI identification for other purposes too. Morph
dmi_dump_ids() which is used to print DMI identification as a debug
message during boot into dmi_format_ids() which formats the same
information sans the leading "DMI:" tag into a string buffer.
dmi_present() is updated to format the information into dmi_ids_string[]
using the new function and print it with "DMI:" prefix.
dmi_ids_string[] will be used for another purpose by a future patch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 9f9c9cbb60 ("drivers/firmware/dmi_scan.c: fetch dmi version
from SMBIOS if it exists") hoisted the check for "_DMI_" into
dmi_scan_machine(), which means that we don't bother to check for
"_DMI_" at offset 16 in an SMBIOS entry. smbios_present() may also call
dmi_present() for an address where we found "_SM_", if it failed further
validation.
Check for "_DMI_" in smbios_present() before calling dmi_present().
[akpm@linux-foundation.org: fix build]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Reported-by: Tim McGrath <tmhikaru@gmail.com>
Tested-by: Tim Mcgrath <tmhikaru@gmail.com>
Cc: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Originally 'efi_enabled' indicated whether a kernel was booted from
EFI firmware. Over time its semantics have changed, and it now
indicates whether or not we are booted on an EFI machine with
bit-native firmware, e.g. 64-bit kernel with 64-bit firmware.
The immediate motivation for this patch is the bug report at,
https://bugs.launchpad.net/ubuntu-cdimage/+bug/1040557
which details how running a platform driver on an EFI machine that is
designed to run under BIOS can cause the machine to become
bricked. Also, the following report,
https://bugzilla.kernel.org/show_bug.cgi?id=47121
details how running said driver can also cause Machine Check
Exceptions. Drivers need a new means of detecting whether they're
running on an EFI machine, as sadly the expression,
if (!efi_enabled)
hasn't been a sufficient condition for quite some time.
Users actually want to query 'efi_enabled' for different reasons -
what they really want access to is the list of available EFI
facilities.
For instance, the x86 reboot code needs to know whether it can invoke
the ResetSystem() function provided by the EFI runtime services, while
the ACPI OSL code wants to know whether the EFI config tables were
mapped successfully. There are also checks in some of the platform
driver code to simply see if they're running on an EFI machine (which
would make it a bad idea to do BIOS-y things).
This patch is a prereq for the samsung-laptop fix patch.
Cc: David Airlie <airlied@linux.ie>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Peter Jones <pjones@redhat.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Steve Langasek <steve.langasek@canonical.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Konrad Rzeszutek Wilk <konrad@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The right dmi version is in SMBIOS if it's zero in DMI region
This issue was originally found from an oracle bug.
One customer noticed system UUID doesn't match between dmidecode & uek2.
- HP ProLiant BL460c G6 :
# cat /sys/devices/virtual/dmi/id/product_uuid
00000000-0000-4C48-3031-4D5030333531
# dmidecode | grep -i uuid
UUID: 00000000-0000-484C-3031-4D5030333531
From SMBIOS 2.6 on, spec use little-endian encoding for UUID other than
network byte order.
So we need to get dmi version to distinguish. If version is 0.0, the
real version is taken from the SMBIOS version. This is part of original
kernel comment in code.
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Cc: Feng Jin <joe.jin@oracle.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As of version 2.6 of the SMBIOS specification, the first 3 fields of the
UUID are supposed to be little-endian encoded.
Also a minor fix to match variable meaning and mute checkpatch.pl
[akpm@linux-foundation.org: tweak code comment]
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Cc: Feng Jin <joe.jin@oracle.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Send the entire DMI (SMBIOS) table to the /dev/random driver to
help seed its pools.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The current implementation of dmi_name_in_vendors() is an invitation to
lazy coding and false positives [1]. Searching for a string in 8 know
what you're looking for, so you should know where to look. strstr isn't
fast, especially when it fails, so we should avoid calling it when it
just can't succeed.
Looking at the current users of the function, it seems clear to me that
they are looking for a system or board vendor name, so let's limit
dmi_name_in_vendors to these two DMI fields. This much better matches
the function name, BTW.
[1] We currently have code looking for short names in DMI data, such as
"IBM", "ASUS" or "Acer". I let you guess what will happen the day other
vendors ship products named, for example, "SCHREIBMEISTER", "PEGASUS" or
"Acerola".
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "Type 2" SMBIOS record that contains Board Name is not
strictly required and may be absent in the SMBIOS on some
platforms.
( Please note that Type 2 is not listed in Table 3 in Sec 6.2
("Required Structures and Data") of the SMBIOS v2.7
Specification. )
Use the Manufacturer Name (aka System Vendor) name.
Print Board Name only when it is present.
Before the fix:
(i) dmesg output: DMI: /ProLiant DL380 G6, BIOS P62 01/29/2011
(ii) oops output: Pid: 2170, comm: bash Not tainted 2.6.38-rc4+ #3 /ProLiant DL380 G6
After the fix:
(i) dmesg output: DMI: HP ProLiant DL380 G6, BIOS P62 01/29/2011
(ii) oops output: Pid: 2278, comm: bash Not tainted 2.6.38-rc4+ #4 HP ProLiant DL380 G6
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: <stable@kernel.org> # .3x - good for debugging, please apply as far back as it applies cleanly
LKML-Reference: <20110214224423.2182.13929.sendpatchset@nchumbalkar.americas.hpqcorp.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Put basic system information in the dmesg log. There are lots of dmesg
logs on the web, and it would be useful if they contained this information
for debugging platform problems. "BOARD/PRODUCT" format copied from
show_regs_common(), which is used in the oops path.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch exports SMBIOS provided firmware instance and label of
onboard PCI devices to sysfs. New files are:
/sys/bus/pci/devices/.../label which contains the firmware name for
the device in question, and
/sys/bus/pci/devices/.../index which contains the firmware device type
instance for the given device.
Signed-off-by: Jordan Hargrave <jordan_hargrave@dell.com>
Signed-off-by: Narendra K <narendra_k@dell.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The purpose of dmi->ident is twofold - it may be used by DMI callback
functions when composing log messages; it is also used to determine
end of DMI table in dmi_check_system() and dmi_first_match(). However,
in case when callbacks are not interested in using ident at all it just
wastes memory. Let's make entries with empty first match slot serve as
end-of-table markers instead.
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There are cases where full date information is required instead of
just the year. Add month and day parsing to dmi_get_year() and rename
it to dmi_get_date().
As the original function only required '/' followed by any number of
parseable characters at the end of the string, keep that behavior to
avoid upsetting existing users.
The new function takes dates of format [mm[/dd]]/yy[yy]. Year, month
and date are checked to be in the ranges of [1-9999], [1-12] and
[1-31] respectively and any invalid or out-of-range component is
returned as zero.
The dummy implementation is updated accordingly but the return value
is updated to indicate field not found which is consistent with how
other dummy functions behave.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Year parsing in dmi_get_year() had the following two bugs.
* "00" is treated as invalid instead of 2000 because zero return from
simple_strtoul() is treated as error.
* "0N" where N >= 8 is treated as invalid of 200N because the leading
0 is considered to specify octal.
Fix the above two bugs by using endptr to detect invalid number and
forcing decimal.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Community reported one SB600 SATA issue(BZ #9412), which led to 64 bit
DMA disablement for all SB600 revisions by driver maintainers with
commits c7a42156d9 and
4cde32fc4b.
But the root cause is ASUS M2A-VM system BIOS bug in old revisions
like 0901, while forcing into 32bit DMA happens to work as workaround.
Now it's time to withdraw 4cde32fc4b
so as to restore the SB600 SATA 64bit DMA capability.
This patch is also adding the workaround for M2A-VM old BIOS revisions,
but users are suggested to upgrade their system BIOS to the latest one
if they meet this issue.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
At the moment, dmi_walk() lacks flexibility, users can't pass data to
the callback function. Add a pointer for private data to make this
function more flexible.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Roland Dreier <rolandd@cisco.com>
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.
To prevent this from happening we can blacklist the affected systems
using DMI information. However, only the on-board controlles should
be blacklisted and their PCI slot numbers can be used for this
purpose. Unfortunately the existing interface for checking DMI
information of the system is not very convenient for this purpose,
because to use it, we would have to define special callback functions
or create a separate struct dmi_system_id table for each blacklisted
system.
To overcome this difficulty introduce a new function
dmi_first_match() returning a pointer to the first entry in an array
of struct dmi_system_id elements that matches the system DMI
information. Then, we can use this pointer to access the entry's
.driver_data field containing the additional information, such as
the PCI slot number, allowing us to do the desired blacklisting.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add missing kernel-doc notation:
drivers/firmware/dmi_scan.c:475: No description found for parameter 'str'
drivers/firmware/dmi_scan.c:592: No description found for parameter 'f'
drivers/firmware/dmi_scan.c:592: No description found for parameter 'str'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a wrapper for testing system_info which will handle also NULL
system infos.
This will be used by the ata PIIX driver.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Alexandru Romanescu <a_romanescu@yahoo.co.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As we've lost our trivial maintainer for the moment I'll send this
directly. Only touches a comment
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: Should permit VMware detection on older platforms where the
vendor is changed. Could theoretically cause a regression if some
weird serial number scheme contains the string "VMware" by pure
chance. Seems unlikely, especially with the mixed case.
In some user configured cases, VMware may choose not to put a VMware specific
DMI string, but the product serial key is always there and is VMware specific.
Add a interface to check the serial key, when checking for VMware in the DMI
information.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
It happened to me recently that i added a dmi_check_system() quirk
in a too early codepath, and it was silently ignored because all the
DMI tables and strings were still empty.
As this situation is clearly a programming error / kernel bug,
warn when it happens, instead of silently ignoring quirks.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The "dmi.h" file did not state anywhere in the file what "DMI" was.
For those who know, it's obvious. For the rest of us, I added a
brief opening comment.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In 2.6.14 a patch was merged which switching the order of the ipmi device
naming from in-order-of-discovery over to reverse-order-of-discovery.
So on systems with multiple BMC interfaces, the ipmi device names are being
created in reverse order relative to how they are discovered on the system
(e.g. on an IBM x3950 multinode server with N nodes, the device name for the
BMC in the first node is /dev/ipmiN-1 and the device name for the BMC in the
last node is /dev/ipmi0, etc.).
The problem is caused by the list handling routines chosen in dmi_scan.c.
Using list_add() causes the multiple ipmi devices to be added to the device
list using a stack-paradigm and so the ipmi driver subsequently pulls them off
during initialization in LIFO order. This patch changes the
dmi_save_ipmi_device() list handling paradigm to a queue, thereby allowing the
ipmi driver to build the ipmi device names in the order in which they are
found on the system.
Signed-off-by: Carol Hebert <cah@us.ibm.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adding the same item to a given linked list more than once is guaranteed
to break and corrupt the list. This is however what we do in dmi_scan
since commit 79da472111 ("x86: fix DMI out
of memory problems").
Given that there is absolutely no interest in saving empty OEM strings
anyway, I propose the simple and efficient fix below: we discard the empty
OEM strings altogether.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Parag Warudkar <parag.warudkar@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we gather on-board devices from both DMI types 10 and 41, there is
a possibility that we list the same device twice. In order to not confuse
drivers, and also to save memory, make sure that we do not add duplicate
devices to the dmi_devices list.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
From version 2.6 of the SMBIOS standard, type 10 (On Board Devices
Information) becomes obsolete. The reason for this is that no further
fields can be added to this structure without adversely affecting existing
software's ability to properly parse the data.
Therefore type 41 (Onboard Devices Extended Information) was added.
The structure is as follows:
struct smbios_type_41 {
u8 type;
u8 length;
u16 handle;
u8 reference_designation_string;
u8 device_type; /* same device type as in type 10 */
u8 device_type_instance;
u16 segment_group_number;
u8 bus_number;
u8 device_function_number;
};
For more info: http://www.dmtf.org/standards/smbios
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Let drivers walk the DMI table for their own needs. Some drivers need
data stored in OEM-specific DMI records for proper operation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Use existing dmi_get_system_info(),
Delete duplicate dmi_get_slot()
Spotted-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Len Brown <len.brown@intel.com>
People with HP Desktops (including me) encounter couple of DMI errors
during boot - dmi_save_oem_strings_devices: out of memory and
dmi_string: out of memory.
On some HP desktops the DMI data include OEM strings (type 11) out of
which only few are meaningful and most other are empty. DMI code
religiously creates copies of these 27 strings (65 bytes each in my
case) and goes OOM in dmi_string().
If DMI_MAX_DATA is bumped up a little then it goes and fails in
dmi_save_oem_strings while allocating dmi_devices of sizeof(struct
dmi_device) corresponding to these strings.
On x86_64 since we cannot use alloc_bootmem this early, the code uses a
static array of 2048 bytes (DMI_MAX_DATA) for allocating the memory DMI
needs. It does not survive the creation of empty strings and devices.
Fix this by detecting and not newly allocating empty strings and instead
using a one statically defined dmi_empty_string.
Also do not create a new struct dmi_device for each empty string - use
one statically define dmi_device with .name=dmi_empty_string and add
that to the dmi_devices list.
On x64 this should stop the OOM with same current size of DMI_MAX_DATA
and on x86 this should save a good amount of (27*65 bytes +
27*sizeof(struct dmi_device) bootmem.
Compile and boot tested on both 32-bit and 64-bit x86.
Signed-off-by: Parag Warudkar <parag.warudkar@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This simply allows other sub-systems (such as ACPI)
to access and print out slots in static dmi_ident[].
Signed-off-by: Len Brown <len.brown@intel.com>
Three main sets of changes:
1) dmi_get_system_info() return value should have been marked const,
since callers should not be changing that data.
2) const-ify DMI internals, since DMI firmware tables should,
whenever possible, be marked const to ensure we never ever write to
that data area.
3) const-ify DMI API, to enable marking tables const where possible
in low-level drivers.
And if we're really lucky, this might enable some additional
optimizations on the part of the compiler.
The bulk of the changes are #2 and #3, which are interrelated. #1 could
have been a separate patch, but it was so small compared to the others,
it was easier to roll it into this changeset.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ivan Khoronzhuk