If we cancel all pending cmds (eg. when tearing down the device), don't
blame it on an IO error.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than delaying the decision until netdev setup, immediately reject
a device when we discover that it has an unsupported link type
(ie. Token Ring).
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a device is configured with ISOLATION_MODE_FWD, traffic never goes
through the internal switch. Don't apply the offload restrictions in
this case.
Fixes: c619e9a6f5 ("s390/qeth: don't use restricted offloads for local traffic")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current(?) OSA devices also store their cmd-specific return codes for
SET_ACCESS_CONTROL cmds into the top-level cmd->hdr.return_code.
So once we added stricter checking for the top-level field a while ago,
none of the error logic that rolls back the user's configuration to its
old state is applied any longer.
For this specific cmd, go back to the old model where we peek into the
cmd structure even though the top-level field indicated an error.
Fixes: 686c97ee29 ("s390/qeth: fix error handling in adapter command callbacks")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 5e1fb45ec8 ("s390/ccwgroup: remove pm support") removed power
management support from the ccwgroup bus driver. So remove the
associated callbacks from all ccwgroup drivers.
CC: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When starting the reset worker via sysfs is unsuccessful, return an
error to the user.
Modernize the sysfs input parsing while at it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When qeth_flush_buffers() gets called for a group of TX buffers
(currently up to 2 for OSA-style devices), the code iterates over each
buffer for some final processing.
During this processing, it sets the TX IRQ marker on the leading buffer
rather than the last one. This can result in delayed TX completion of
the trailing buffers. So pull the IRQ marker code out of the loop, and
apply it to the final buffer.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX path usually maps the full content of a page into a buffer
element. But there's specific skb layouts (ie. linearized TSO skbs)
where the HW header (1) requires a separate buffer element, and (2) is
page-contiguous with the packet data that's mapped into the next buffer
element.
Flag such buffer elements accordingly, so that HW can optimize its data
access for them.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the __qeth_fill_buffer() helper into its only caller. This way all
mapping-related context is in one place, and we can make some more use
of it in a subsequent patch.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current OSA models don't support TSO for traffic to local next-hops, and
some old models didn't offer TX CSO for such packets either.
So as part of .ndo_features_check, check if a packet's next-hop resides
on the same OSA Adapter. Opt out from affected HW offloads accordingly.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For debugging purposes, provide read access to the local_addr caches
via debug/qeth/<dev_name>/local_addrs.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In configurations where specific HW offloads are in use, OSA adapters
will raise notifications to their virtual devices about the IP addresses
that currently reside on the same adapter.
Cache these addresses in two RCU-enabled hash tables, and flush the
tables once the relevant HW offload(s) get disabled.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling TX CSO, make a note of whether the device has support for
LP2LP offloading. This will become relevant in subsequent patches.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introduction of TX coalescing, .ndo_start_xmit now potentially
starts the TX completion timer. So only kill the timer _after_ TX has
been disabled.
Fixes: ee1e52d1e4 ("s390/qeth: add TX IRQ coalescing support for IQD devices")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upper-layer drivers allocate their SBALs by calling qdio_alloc_buffers()
for each individual queue. But when later passing the SBAL addresses to
qdio_establish(), they need to be in a single array of pointers.
So if the driver uses multiple Input or Output queues, it needs to
allocate a temporary array just to present all its SBAL pointers in this
layout.
This patch slightly changes the format of the QDIO initialization data,
so that drivers can pass a per-queue array where each element points to
a queue's SBAL array.
zfcp doesn't use multiple queues, so the impact there is trivial.
For qeth this brings a nice reduction in complexity, and removes
a page-sized allocation.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
All that qdio_allocate() actually uses from the init_data is the cdev,
and the number of Input and Output Queues. Have the driver pass those as
parameters, and defer the init_data processing into qdio_establish().
This includes writing per-device(!) trace entries, and most of the
sanity checks.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The last machine generation that supports OSN is z13, and OSX is only
supported up to z14. Allow users and distros to decide whether they
still need support for these device types.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace list_for_each() with list_for_each_entry(), and
list_entry(head.next) with list_first_entry().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a device is configured in prio-queue mode to pin all traffic onto
a specific HW queue, treat this as a distinct variant of prio-queueing
instead of QETH_NO_PRIO_QUEUEING.
This corrects an error message from qeth_osa_set_output_queues() for
devices configured in such a mode.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since IQD devices complete (most of) their transmissions synchronously,
they don't offer TX completion IRQs and have no HW coalescing controls.
But we can fake the easy parts in SW, and give the user some control wrt
to how often the TX NAPI code should be triggered to process the TX
completions.
Having per-queue controls can in particular help the dedicated mcast
queue, as it likely benefits from different fine-tuning than what the
ucast queues need.
CC: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Count the number of TX doorbells we issue to the qdio layer.
Also count the number of actual frames in a TX buffer, and then
use this data along with the byte count during TX completion.
We'll make additional use of the frame count in a subsequent patch.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the support for polling drivers was initially added, it only
considered Input Queue 0. But as QDIO interrupts are actually for the
full device and not a single queue, this doesn't really fit for
configurations where multiple Input Queues are used.
Rework the qdio code so that interrupts for a polling driver are not
split up into actions for each queue. Instead deliver the interrupt as
a single event, and let the driver decide which queue needs what action.
When re-enabling the QDIO interrupt via qdio_start_irq(), this means
that the qdio code needs to
(1) put _all_ eligible queues back into a state where they raise IRQs,
(2) and afterwards check _all_ eligible queues for new work to bridge
the race window.
On the qeth side of things (as the only qdio polling driver), we can now
add CQ polling support to the main NAPI poll routine. It doesn't consume
NAPI budget, and to avoid hogging the CPU we yield control after
completing one full queue worth of buffers.
The subsequent qdio_start_irq() will check for any additional work, and
have us re-schedule the NAPI instance accordingly.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever all completed RX buffers have been processed
(ie. rx->b_count == 0), we call down to the HW layer to scan for
additional buffers. If no further buffers are available, the code
breaks out of the while-loop.
So we never reach the 'process an RX buffer' step with rx->b_count == 0,
eliminate that check and one level of indentation.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main NAPI poll routine should eventually handle more types of work,
beyond just the RX ring.
Split off the RX poll logic into a separate function, and simplify the
nested while-loop.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since RX buffers may contain multiple packets, qeth's NAPI poll code can
exhaust its budget in the middle of an RX buffer. Thus we keep track of
our current position within the active RX buffer, so we can resume
processing here in the next NAPI poll period.
Clean up that code by tracking the index of the active buffer element,
instead of a pointer to it.
Also simplify the code that advances to the next RX buffer when the
current buffer has been fully processed.
v2: - remove QDIO_ELEMENT_NO() macro (davem)
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_do_ioctl() is only reached through our own net_device_ops, so we
can trust that dev->ml_priv still contains what we put there earlier.
qeth_bridgeport_an_set() is an internal function that doesn't require
such sanity checks.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Data addresses in the AOB are absolute, and need to be translated before
being fed into kmem_cache_free(). Currently this phys_to_virt() is a no-op.
Also see commit 2db01da8d2 ("s390/qdio: fill SBALEs with absolute addresses").
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for SOF_TIMESTAMPING_TX_SOFTWARE.
No support for non-IQD devices, since they orphan the skb in their xmit
path.
To play nice with TX bulking, set the timestamp when the buffer that
contains the skb(s) is actually flushed out to HW.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ucast traffic, qeth_iqd_select_queue() falls back to
netdev_pick_tx(). This will potentially use skb_tx_hash() to distribute
the flow over all active TX queues - so txq 0 is a valid selection, and
qeth_iqd_select_queue() needs to check for this and put it on some other
queue. As a result, the distribution for ucast flows is unbalanced and
hits QETH_IQD_MIN_UCAST_TXQ heavier than the other queues.
Open-coding a custom variant of skb_tx_hash() isn't an option, since
netdev_pick_tx() also gives us eg. access to XPS. But we can pull a
little trick: add a single TC class that excludes the mcast txq, and
thus encourage skb_tx_hash() to not pick the mcast txq.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the support for z/VM NICs, but we need to take extra care
about the dedicated mcast queue:
1. netdev_pick_tx() is unaware of this limitation and might select the
mcast txq. Catch this.
2. require at least _two_ TX queues - one for ucast, one for mcast.
3. when reducing the number of TX queues, there's a potential race
where netdev_cap_txqueue() over-rules the selected txq index and
falls back to index 0. This would place ucast traffic on the mcast
queue, and result in TX errors.
So for IQD, reject a reduction while the interface is running.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
z/VM NICs don't offer HW QoS for TX rings. So just use netdev_pick_tx()
to distribute the connections equally over all enabled TX queues.
We start with just 1 enabled TX queue (this matches the typical
configuration without prio-queueing). A follow-on patch will allow users
to enable additional TX queues.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When falling back to an allocation from the HW header cache, check if
the skb is eligible for using memory reserves.
This only makes a difference if the cache is empty and needs to be
refilled.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_alloc_page() for backing the RX buffers with pages. This way we
pick up __GFP_MEMALLOC.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX buffer pool is allocated in qeth_alloc_qdio_queues().
A subsequent pool resizing is then handled in a very simple way:
first free the current pool, then allocate a new pool of the requested
size.
There's two ways where this can go wrong:
1. if the resize action happens _before_ the initial pool was allocated,
then a subsequent initialization will call qeth_alloc_qdio_queues()
and fill the pool with a second(!) set of pages. We consume twice the
planned amount of memory.
This is easy to fix - just skip the resizing if the queues haven't
been allocated yet.
2. if the initial pool was created by qeth_alloc_qdio_queues() but a
subsequent resizing fails, then the device has no(!) RX buffer pool.
The next initialization will _not_ call qeth_alloc_qdio_queues(), and
attempting to back the RX buffers with pages in
qeth_init_qdio_queues() will fail.
Not very difficult to fix either - instead of re-allocating the whole
pool, just allocate/free as many entries to match the desired size.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for a subsequent fix, split out helpers to allocate/free
individual pool entries.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX buffer elements are always backed with full pages, reflect this
in the pointer type.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When qeth's napi poll code fails to refill an entirely empty RX ring, it
kicks off buffer_reclaim_work to try again later.
Make sure that this worker is cancelled when setting the qeth device
offline. Otherwise a RX refill action can unexpectedly end up running
concurrently to bigger re-configurations (eg. resizing the buffer pool),
without any locking.
Fixes: b333293058 ("qeth: add support for af_iucv HiperSockets transport")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_init_qdio_queues() fills the RX ring with an initial set of
RX buffers. If qeth_init_input_buffer() fails to back one of the RX
buffers with memory, we need to bail out and report the error.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an OSA device in prio-queue setup is reduced to 1 TX queue due to
HW restrictions, we reset its the default_out_queue to 0.
In the old code this was needed so that qeth_get_priority_queue() gets
the queue selection right. But with proper multiqueue support we already
reduced dev->real_num_tx_queues to 1, and so the stack puts all traffic
on txq 0 without even calling .ndo_select_queue.
Thus we can preserve the user's configuration, and apply it if the OSA
device later re-gains support for multiple TX queues.
Fixes: 73dc2daf11 ("s390/qeth: add TX multiqueue support for OSA devices")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once the call to qdio_establish() has completed, qdio is free to deliver
data IRQs to the device driver's IRQ poll handler.
For qeth (the only qdio driver that currently uses IRQ polling) this is
problematic, since the IRQs can arrive before its NAPI instance is
even registered. Calling napi_schedule() from qeth_qdio_start_poll()
then crashes in various nasty ways.
Until recently qeth checked for IFF_UP to drop such early interrupts,
but that's fragile as well since it doesn't enforce any ordering.
Fix this properly by bringing up the qdio device in IRQS_DISABLED mode,
and have the driver explicitly opt-in to receive data IRQs.
qeth does so from qeth_open(), which kick-starts a NAPI poll and then
calls qdio_start_irq() from qeth_poll().
Also add a matching qdio_stop_irq() in qeth_stop() to switch the qdio
dataplane back into a disabled state.
Fixes: 3d35dbe622 ("s390/qeth: don't check for IFF_UP when scheduling napi")
CC: Qian Cai <cai@lca.pw>
Reported-by: Qian Cai <cai@lca.pw>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mptcp conflict was overlapping additions.
The SMC conflict was an additional and removal happening at the same
time.
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the ethtool hooks for the ETHTOOL_RX_COPYBREAK tunable.
The copybreak is stored into netdev_priv, so that we automatically go
back to the default value if the netdev is re-allocated.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trust the napi_disable() in qeth_stop() to handle this.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once the IDX connection is down, there's no point in trying to issue
more IOs.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This let's us start every new IDX connection with clean seqnos.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Remove ieee_emulation_warnings sysctl which is a dead code.
- Avoid triggering rebuild of the kernel during make install.
- Enable protected virtualization guest support in default configs.
- Fix cio_ignore seq_file .next function to increase position index. And
use kobj_to_dev instead of container_of in cio code.
- Fix storage block address lists to contain absolute addresses in
qdio code.
- Few clang warnings and spelling fixes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAl5RI0sACgkQjYWKoQLX
FBig0Af/bJjFspbGFN+YEO+XM3AbURu0lHxq25r0EoSEc9acfS5nMrUk7OhNktND
w+m/PoyOg8elB3LDkalz9IP6CZANSSoGV5aKyg3Wp06Wu//DdwAMJWqFOyosJ89z
zVOSGgX3zHFarodS4suDPTEdDEcSMVVvqnz1A81dQD9QNWyVCutqYABj3OEittOD
EBYchT7Qs/ObwbP+RaUa0swbrq11P8hZSAblbjkbuFpw45CdQ6rFoyJO1Tccuyh7
puNlPLpkDI15RNxC+vh+4NItcxPcIL+Qa0kltbQJLq7aq/UqLNF02vLjWluH4hG6
i6+ZzsIra5gdtdf2cPFiKo7EagpQ2w==
=CRBt
-----END PGP SIGNATURE-----
Merge tag 's390-5.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- Remove ieee_emulation_warnings sysctl which is a dead code.
- Avoid triggering rebuild of the kernel during make install.
- Enable protected virtualization guest support in default configs.
- Fix cio_ignore seq_file .next function to increase position index.
And use kobj_to_dev instead of container_of in cio code.
- Fix storage block address lists to contain absolute addresses in qdio
code.
- Few clang warnings and spelling fixes.
* tag 's390-5.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/qdio: fill SBALEs with absolute addresses
s390/qdio: fill SL with absolute addresses
s390: remove obsolete ieee_emulation_warnings
s390: make 'install' not depend on vmlinux
s390/kaslr: Fix casts in get_random
s390/mm: Explicitly compare PAGE_DEFAULT_KEY against zero in storage_key_init_range
s390/pkey/zcrypt: spelling s/crytp/crypt/
s390/cio: use kobj_to_dev() API
s390/defconfig: enable CONFIG_PROTECTED_VIRTUALIZATION_GUEST
s390/cio: cio_ignore_proc_seq_next should increase position index
The RX copybreak is intended as the _max_ value where the frame's data
should be copied. So for frame_len == copybreak, don't build an SG skb.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann