ARM-based 63xx DSL platforms have the spi-bcm63xx-hsspi controller
present, allow using this driver there as well.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support to use McSPI controller as SPI slave. In slave mode, DMA TX
completion does not mean entire data has been shifted out as data might
still be stuck in FIFO waiting for master to clock the bus. Therefore,
add an IRQ handler for slave mode to know when entire data in FIFO has
been shifted out.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
McSPI has 32 byte FIFO in Transmit-Receive mode. Current code tries to
configuration FIFO watermark level for DMA trigger to be GCD of transfer
length and max FIFO size which would mean trigger level may be set to 32
for transmit-receive mode if length is aligned. This does not work in
case of SPI slave mode where FIFO always needs to have data ready
whenever master starts the clock. With DMA trigger size of 32 there will
be a small window during slave TX where DMA is still putting data into
FIFO but master would have started clock for next byte, resulting in
shifting out of stale data. Similarly, on Slave RX side there may be RX
FIFO overflow
Fix this by setting FIFO watermark for DMA trigger to word
length. This means DMA is triggered as soon as FIFO has space for word
length bytes and DMA would make sure FIFO is almost always full
therefore improving FIFO occupancy in both master and slave mode.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use standard readl_poll_timeout() macro for polling on status bits.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The qspi controller is a specialized communication interface
targeting single, dual or quad SPI Flash memories (NOR/NAND).
It can operate in any of the following modes:
-indirect mode: all the operations are performed using the quadspi
registers
-read memory-mapped mode: the external Flash memory is mapped to the
microcontroller address space and is seen by the system as if it was
an internal memory
tested on:
-NOR: mx66l51235l
-NAND: MT29F2G01ABAGD
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DMA API does its own zone decisions based on the coherent_dma_mask.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 9ec36cafe4 ("of/irq: do irq resolution in platform_get_irq")
platform_get_irq() can return -EPROBE_DEFER. However, the driver overrides
an error returned by that function with -ENOENT which breaks the deferred
probing. Propagate upstream an error code returned by platform_get_irq()
and remove the bogus "platform" from the error message, while at it...
Fixes: 9ec36cafe4 ("of/irq: do irq resolution in platform_get_irq")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use PIO mode instead if size is smaller than fifo size, since
dma may be less efficient.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct wml as the last rx sg length instead of the whole transfer
length. Otherwise, mtd_stresstest will be failed as below:
insmod mtd_stresstest.ko dev=0
=================================================
mtd_stresstest: MTD device: 0
mtd_stresstest: not NAND flash, assume page size is 512 bytes.
mtd_stresstest: MTD device size 4194304, eraseblock size 65536, page size 512, count of eraseblocks 64, pa0
mtd_stresstest: doing operations
mtd_stresstest: 0 operations done
mtd_test: mtd_read from 1ff532, size 880
mtd_test: mtd_read from 20c267, size 64998
spi_master spi0: I/O Error in DMA RX
m25p80 spi0.0: SPI transfer failed: -110
spi_master spi0: failed to transfer one message from queue
mtd_test: error: read failed at 0x20c267
mtd_stresstest: error -110 occurred
=================================================
insmod: ERROR: could not insert module mtd_stresstest.ko: Connection timed out
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current dynamic burst length is based on the whole transfer length,
that's ok if there is only one sg, but is not right in case multi sgs
in one transfer,because the tail data should be based on the last sg
length instead of the whole transfer length. Move wml setting for DMA
to the later place, thus, the next patch could get the right last sg
length for wml setting. This patch is a preparation one, no any
function change involved.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI configuration state includes an SPI_NO_CS flag that disables
all CS line manipulation, for applications that want to manage their
own chip selects. However, this flag is ignored by the GPIO CS code
in the SPI framework.
Correct this omission with a trivial patch.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MMP2 platform, that uses device tree, has this controller. Let's add
devicetree alongside platform & PCI.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver supports GENI based SPI Controller in the Qualcomm SOCs. The
Qualcomm Generic Interface (GENI) is a programmable module supporting a
wide range of serial interfaces including SPI. This driver supports SPI
operations using FIFO mode of transfer.
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Dilip Kota <dkota@codeaurora.org>
Signed-off-by: Alok Chauhan <alokc@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Let the dma/non-dma code paths handle the spi enable
flag themselves. This removes some logic to determine
if the flag should be turned on before or after dma
and also don't leave the spi enabled if the dma path
fails.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dma direction for the tx and rx dma channels never
change, so just use the constants directly rather
than storing them in device data.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver data has a u32 field use_dma which is
only ever used as a boolean, so change its type
to reflect that.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
We no longer need the dma_caps since the dma driver
already clamps the burst length to the hardware limit,
so don't request and store dma_caps in device data.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signal tx dma when spi fifo is less than half full,
and limit tx bursts to half the fifo length.
Clamp rx burst length to 1 to avoid alignment issues.
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rxconf and txconf structs are allocated on the
stack, so make sure we zero them before filling out
the relevant fields.
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
New driver for Qualcomm QuadSPI(QSPI) controller that is used to
communicate with slaves such as flash memory devices. The QSPI controller
can operate in 2 or 4 wire mode but only supports SPI Mode 0. The
controller can also operate in Single or Dual data rate modes.
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for a new devicetree compatible string called
'amazon,alpine-apb-ssi', which is necessary for the Amazon Alpine spi
controller. 'amazon,alpine-dw-apb-ssi' is used in the dw spi driver if
specified in the devicetree. Otherwise, fall back to driver default
behavior, i.e. original dw IP hw driver behavior.
Signed-off-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixing/optimizing bcm_qspi_bspi_read() performance introduced two
changes:
1) It added a loop to read all requested data using multiple BSPI ops.
2) It bumped max size of a single BSPI block request from 256 to 512 B.
The later change resulted in occasional BSPI timeouts causing a
regression.
For some unknown reason hardware doesn't always handle reads as expected
when using 512 B chunks. In such cases it may happen that BSPI returns
amount of requested bytes without the last 1-3 ones. It provides the
remaining bytes later but doesn't raise an interrupt until another LR
start.
Switching back to 256 B reads fixes that problem and regression.
Fixes: 345309fa7c ("spi: bcm-qspi: Fix bcm_qspi_bspi_read() performance")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
During implementation of the new API bcm_qspi_bspi_set_flex_mode() has
been modified breaking calculation of address length. An unnecessary
multiplication was added breaking flash reads.
Fixes: 5f195ee7d8 ("spi: bcm-qspi: Implement the spi_mem interface")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
spidev will make a big fuss if a device tree node binds a device by
using "spidev" as the node's compatible property.
However, the logic for this isn't looking for "spidev" in the
compatible, but rather checking that the device is NOT compatible with
spidev's list of devices.
This causes a false positive if a device not named "rohm,dh2228fv", etc.
binds to spidev, even if a means other than putting "spidev" in the
device tree was used. E.g., the sysfs driver_override attribute.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
This attribute works the same was as the identically named attribute
for PCI, AMBA, and platform devices. For reference, see:
commit 3cf3857134 ("ARM: 8256/1: driver coamba: add device binding
path 'driver_override'")
commit 3d713e0e38 ("driver core: platform: add device binding path
'driver_override'")
commit 782a985d7a ("PCI: Introduce new device binding path using
pci_dev.driver_override")
If the name of a driver is written to this attribute, then the device
will bind to the named driver and only the named driver.
The device will bind to the driver even if the driver does not list the
device in its id table. This behavior is different than the driver's
bind attribute, which only allows binding to devices that are listed as
supported by the driver.
It can be used to bind a generic driver, like spidev, to a device.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Certain devices don't work well when a transmit FIFO underrun or
receive FIFO overrun occurs. Example is the SAF400x radio chip when
running at high speed which leads to garbage being sent to/received from
the chip. In which case, it should stall waiting for further data to be
available before proceeding. This patch unset the NOSTALL bit in CFGR1
by default to prevent this issue.
Signed-off-by: Hieu Tran Dang <dangtranhieu2012@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clang warns when one enumerated type is implicitly converted to another.
drivers/spi/spi-ep93xx.c:342:62: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
nents = dma_map_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:428:58: note: expanded from macro
'dma_map_sg'
#define dma_map_sg(d, s, n, r) dma_map_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~ ^
drivers/spi/spi-ep93xx.c:348:57: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:429:62: note: expanded from macro
'dma_unmap_sg'
#define dma_unmap_sg(d, s, n, r) dma_unmap_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~~~ ^
drivers/spi/spi-ep93xx.c:377:56: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:429:62: note: expanded from macro
'dma_unmap_sg'
#define dma_unmap_sg(d, s, n, r) dma_unmap_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~~~ ^
3 warnings generated.
dma_{,un}map_sg expect an enum of type dma_data_direction but this
driver uses dma_transfer_direction for everything. Convert the driver to
use dma_data_direction for these two functions.
There are two places that strictly require an enum of type
dma_transfer_direction: the direction member in struct dma_slave_config
and the direction parameter in dmaengine_prep_slave_sg. To avoid using
an explicit cast, add a simple function, ep93xx_dma_data_to_trans_dir,
to safely map between the two types because they are not 1 to 1 in
meaning.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With this commit the DSPI driver on the BK4 board can be used for SPI
transmission managed from user space (via /dev/spidev0.0).
Example usage/testing:
insmod ./spi-fsl-dspi.ko
./spidev_test -D /dev/spidev0.0 -s 3000000 -v -H -b 8 -p "\xCC\x11\x22\x74"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rewrite switch code block to directly do the expected number
of shifts in each case and have break statements.
Addresses-Coverity-ID: 1056539 ("Missing break in switch")
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Apparently, this code does not actually fall through to the next case
because the machine restarts before it has a chance. However, for the
sake of maintenance and readability, we better add the missing break
statement.
Addresses-Coverity-ID: 1437892 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Quite a few fixes for the Renesas drivers in here, plus a fix for the
Tegra driver and some documentation fixes for the recently added spi-mem
code. The Tegra fix is relatively large but fairly straightforward and
mechanical, it runs on probe so it's been reasonably well covered in
-next testing.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAluuOnETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0AhkB/9ahKdmxdxu0uuzzvS5qmdGD+98dTaV
M+7+Bq6CJfBz0YTc9dxTiynbJot15vo5mKDZkDaJrgOoLCWWDGWa/DjRif2qS2o9
QxjWlBPzfOhKb81/HMJ+MaIHYDtAxvCu4iZExUZPxZzypX8Q9U3+9a/u0+JnRug2
guQ/4vYdxTGbR/taFsKLzf28DRqQb74KuDRAHaN44UYBxA1begy5gFOc7cEQTRu0
WACGM8jNL2eWWLXDNnQQTfb2t1v7LbbMorazyCn2e5ujamE4+DSaYWJF5axZiaQN
ZcRVATw0SPiQlsQW/G014SSFJT0waybxWLOynWS9MSgjx84/GRYWvxRv
=3ATM
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v4.19-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Mark writes:
"spi: Fixes for v4.19
Quite a few fixes for the Renesas drivers in here, plus a fix for the
Tegra driver and some documentation fixes for the recently added
spi-mem code. The Tegra fix is relatively large but fairly
straightforward and mechanical, it runs on probe so it's been
reasonably well covered in -next testing."
* tag 'spi-fix-v4.19-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-mem: Move the DMA-able constraint doc to the kerneldoc header
spi: spi-mem: Add missing description for data.nbytes field
spi: rspi: Fix interrupted DMA transfers
spi: rspi: Fix invalid SPI use during system suspend
spi: sh-msiof: Fix handling of write value for SISTR register
spi: sh-msiof: Fix invalid SPI use during system suspend
spi: gpio: Fix copy-and-paste error
spi: tegra20-slink: explicitly enable/disable clock
The of_find_spi_device_by_node() helper function is useful for other
modules too. Export the funciton as GPL like all other spi helper
functions and make it available if CONFIG_OF is enabled, because it isn't
related to the CONFIG_OF_DYNAMIC context. Finally add a stub if
CONFIG_OF isn't enabled, so others must not care about it.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the appropriate SPDX license identifier and drop the previous
license text.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
On r8a7791/koelsch:
m25p80 spi0.0: error -22 reading 9f
m25p80: probe of spi0.0 failed with error -22
Apparently the logic in spi_mem_check_op() is wrong, rejecting the
spi-mem operation if any buswidth is valid, instead of invalid.
Fixes: 380583227c ("spi: spi-mem: Add extra sanity checks on the op param")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The __exit section is left out for built-in drivers, so a
'remove' callback must not be marked as such to avoid breaking when
we unbind a device at runtime. This was pointed out by kbuild:
`sprd_spi_remove' referenced in section `.data' of drivers/spi/spi-sprd.o: defined in discarded section `.exit.text' of drivers/spi/spi-sprd.o
Fixes: e7d973a31c ("spi: sprd: Add SPI driver for Spreadtrum SC9860")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clang warns when one enumerated type is converted implicitly to another:
drivers/spi/spi-pic32.c:323:8: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
DMA_FROM_DEVICE,
^~~~~~~~~~~~~~~
drivers/spi/spi-pic32.c:333:8: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
DMA_TO_DEVICE,
^~~~~~~~~~~~~
2 warnings generated.
Use the proper enums from dma_transfer_direction (DMA_FROM_DEVICE =
DMA_DEV_TO_MEM = 2, DMA_TO_DEVICE = DMA_MEM_TO_DEV = 1) to satify Clang.
Link: https://github.com/ClangBuiltLinux/linux/issues/159
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some combinations are simply not valid and should be rejected before
the op is passed to the SPI controller driver.
Add an spi_mem_check_op() helper and use it in spi_mem_exec_op() and
spi_mem_supports_op() to make sure the spi-mem operation is valid.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This remove the check and subsequent return of error for the case when
a SPI device requires SPI_CS_WORD and is also configured to use a GPIO
for the CS line.
Commit a134cc414e86 ("spi: always use software fallback for SPI_CS_WORD
when using cs_gio") handles this case now, so this check is no longer
necessary.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This modifies the condition for using the software fallback
implementation for SPI_CS_WORD when the SPI controller is using a GPIO
for the CS line. When using a GPIO for CS, the hardware implementation
won't work, so we just enable the software fallback globally in this
case.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mediatek SPI driver modifies some fields (tx_buf, rx_buf, len, tx_dma,
rx_dma) of the spi_transfer* passed in when doing transfer_one and in
interrupt handler. This is somewhat unexpected, and there are some
caller (e.g. Cr50 spi driver) that reuse the spi_transfer for multiple
messages. Add a field to record how many bytes have been transferred,
and calculate the right len / buffer based on it instead.
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Change-Id: I23e218cd964f16c0b2b26127d4a5ca6529867673
Signed-off-by: Mark Brown <broonie@kernel.org>
If the pll clock needs to be enabled to get its rate, it will also need
to be enabled to provide it. So ensure it is kept enabled through the
lifetime of the device.
Fixes: 0d7412ed1f ("spi/bcm63xx-hspi: Enable the clock before calling clk_get_rate().")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It makes no sense to remove the device on shutdown. And it break things
when the hardware crucial for shutdown (such as the embedded controller)
is attached to the SPI bus.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for the SPI_CS_WORD flag to the TI DaVinci SPI
driver. This mode can be used as long as we are using the hardware
chip select and not a GPIO chip select.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Linus Torvalds