Now, some of the rockchip hardware platforms do enable
lvds in mainline tree.
So, enable Rockchip LVDS driver via default defconfig.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20201109181017.206834-8-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Engicam PX30 carrier boards like EDIMM2.2 and C.TOUCH2.0 have
an onboard Sterling-LWD Wifi/BT chip based on BCM43430 connected
on the UART bus.
UART bus on the design routed via USB to UART CP20x bridge. This
bridge powered from 3V3 regualtor gpio.
This patch adds BT enablement nodes for these respective boards.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20201109181017.206834-7-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Engicam PX30 carrier boards like EDIMM2.2 and C.TOUCH2.0 have
an onboard Sterling-LWD Wifi/BT chip based on BCM43430 connected
on the SDIO bus.
The SDIO power sequnce is connacted with exteernal 32KHz oscillator
and it require 3V3 regulator input.
This patch adds WiFi enablement nodes for these respective boards.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20201109181017.206834-6-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
C.TOUCH 2.0 is a general purpose carrier board with capacitive
touch interface support.
10.1" OF is a capacitive touch 10.1" Open Frame panel solutions.
PX30.Core needs to mount on top of C.TOUCH 2.0 carrier with pluged
10.1" OF for creating complete PX30.Core C.TOUCH 2.0 10.1" Open Frame.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20201109181017.206834-5-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Engicam EDIMM2.2 and C.Touch 2.0 Kits support USB Host
and OTG ports.
Add support to enable USB on these kits while mounting
px30-core SOM.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20201109181017.206834-2-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example this error:
/arch/arm64/boot/dts/rockchip/rk3399-evb.dt.yaml:
sdhci@fe330000: $nodename:0: 'sdhci@fe330000'
does not match '^mmc(@.*)?$'
Fix it by renaming sdhci to mmc.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/
mmc/arasan,sdhci.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20201116132311.8318-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Now that driver support for the RK3328's audio codec, and the plumbing
is defined at the SoC level, we can enable analog audio at the board
level.
Enable analog audio by enabling the codec and the I2S interface
connected and the simple-audio-card that binds them together.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201126073336.30794-4-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The RK3328-ROC-CC already has HDMI display output enabled. Now that
audio for the HDMI controller is supported, it can be enabled as well.
Enable the simple-audio-card, and the I2S interface the audio is fed
from.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201126073336.30794-3-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The board has a standard USB A female port connected to the USB OTG
controller's data pins. Set dr_mode in the OTG controller node to
indicate this usage, instead of having the implementation guess.
Fixes: 2171f4fdac ("arm64: dts: rockchip: add roc-rk3328-cc board")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201126073336.30794-2-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
idle path. Similar to the entry path the low level idle functions have to
be non-instrumentable.
-----BEGIN PGP SIGNATURE-----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=raED
-----END PGP SIGNATURE-----
Merge tag 'locking-urgent-2020-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
"Two more places which invoke tracing from RCU disabled regions in the
idle path.
Similar to the entry path the low level idle functions have to be
non-instrumentable"
* tag 'locking-urgent-2020-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
intel_idle: Fix intel_idle() vs tracing
sched/idle: Fix arch_cpu_idle() vs tracing
Use property name `phy-handle` instead of the deprecated `phy` to
connect eth2 to the PHY.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 7109d817db ("arm64: dts: marvell: add DTS for Turris Mox")
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
There are two SATA ports per CP110. Each of them has a dedicated
interrupt. Describe the real hardware by adding two SATA ports to the
CP110 SATA node.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This adds support for ESPRESSObin-Ultra from Globalscale.
Specifications are similar to the base ESPRESSObin board, with main
difference being being WAN port with PoE capability and 2 additional ethernet ports.
Full specifications:
1x Marvell 64 bit Dual Core ARM A53 Armada 3700 SOC clocked up to 1.2Ghz
1x Topaz 6341 Networking Switch
1GB DDR4
8GB eMMC
1x WAN with 30W POE
4x Gb LAN
1x RTC Clock and battery
1x DC Jack
1x USB 3.0 Type A
1x USB 2.0 Type A
1x SIM NanoSIM card Slot
1x Power Button
4x LED
1x Reset button
1x microUSB for UART
1x M.2 2280 slot for memory
1x 2x2 802.11ac Wi-Fi
1x MiniPCIE slot for Wi-Fi (PCIe interface)
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
LED2 is connected to MPP1_2 pin. It is working only on V7 boards.
V5 boards have hw bug which cause that LED2 is non-working.
So enable LED2 only for Espressobin V7 boards.
Note that LED1 is connected to LED_WLAN# pin on miniPCIe card and LED3 to
power supply. Therefore on Espressobin board only LED2 can be controlled
directly from the host. LED1 is possible to control via WiFi card inserted
in miniPCIe slot if driver for particular card supports it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Gérald Kerma <gerald@gk2.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Add initial support for the IEI Puzzle-M801 1U Rackmount Network
Appliance board.
The board is based on the quad-core Marvell Armada 8040 SoC and supports
up to 16 GB of DDR4 2400 MHz ECC RAM. It has a PCIe x16 slot (x2 lanes
only) and an M.2 type B slot.
Main system hardware:
2x USB 3.0
4x Gigabit Ethernet
2x SFP+
1x SATA 3.0
1x M.2 type B
1x RJ45 UART
1x SPI flash
1x IEI WT61P803 PUZZLE Microcontroller
1x EPSON RX8010 RTC (used instead of the integrated Marvell RTC controller)
6x SFP+ LED
1x HDD LED
All of the hardware listed above is supported and tested in this port.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
eMMC definitions in files armada-3720-espressobin-emmc.dts and
armada-3720-espressobin-v7-emmc.dts is same. So move it into common
armada-3720-espressobin.dtsi file with status "disabled".
This change simplifies eMMC variants of DTS files for Espressobin.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andre Heider <a.heider@gmail.com>
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The included armada-37xx.dtsi already defines these two aliases.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Now that the switch ports have a label in the .dtsi, simplify the whole
"switch0" block for the v7 dts files.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
There are couple of places where INTA interrupt controller
lacks #interrupt-cells property. This leads to warnings of
the type:
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi:147.51-156.5: Warning (interrupt_provider): /bus@100000/main-navss/interrupt-controller@33d00000: Missing #interrupt-cells in interrupt provider
when building TI device-tree files with W=2 warning level.
Fix these.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201127210128.9151-1-nsekhar@ti.com
Our Meltdown mitigation state isn't exposed outside of cpufeature.c,
contrary to the rest of the Spectre mitigation state. As we are going
to use it in KVM, expose a arm64_get_meltdown_state() helper which
returns the same possible values as arm64_get_spectre_v?_state().
Signed-off-by: Marc Zyngier <maz@kernel.org>
Enable the ARM SCMI protocol and the common clock, cpufreq, reset and
sensors drivers. Broadcom STB platforms (ARCH_BRCMSTB) implement SCMI to
provide support for CPU frequency scaling, clock configuration and
temperature and current sensors.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Another set of patches for devicetree files and Arm
SoC specific drivers:
- A fix for OP-TEE shared memory on non-SMP systems
- multiple code fixes for the OMAP platform, including
one regression for the CPSW network driver and a few
runtime warning fixes
- Some DT patches for the Rockchip RK3399 platform,
in particular fixing the MMC device ordering that
recently became nondeterministic with async probe.
- Multiple DT fixes for the Tegra platform, including
a regression fix for suspend/resume on TX2
- A regression fix for a user-triggered fault in the
NXP dpio driver
- A regression fix for a bug caused by an earlier bug
fix in the xilinx firmware driver
- Two more DTC warning fixes
- Sylvain Lemieux steps down as maintainer for the
NXP LPC32xx platform
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=yGOq
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-fixes-v5.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Another set of patches for devicetree files and Arm SoC specific
drivers:
- A fix for OP-TEE shared memory on non-SMP systems
- multiple code fixes for the OMAP platform, including one regression
for the CPSW network driver and a few runtime warning fixes
- Some DT patches for the Rockchip RK3399 platform, in particular
fixing the MMC device ordering that recently became
nondeterministic with async probe.
- Multiple DT fixes for the Tegra platform, including a regression
fix for suspend/resume on TX2
- A regression fix for a user-triggered fault in the NXP dpio driver
- A regression fix for a bug caused by an earlier bug fix in the
xilinx firmware driver
- Two more DTC warning fixes
- Sylvain Lemieux steps down as maintainer for the NXP LPC32xx
platform"
* tag 'arm-soc-fixes-v5.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (24 commits)
arm64: tegra: Fix Tegra234 VDK node names
arm64: tegra: Wrong AON HSP reg property size
arm64: tegra: Fix USB_VBUS_EN0 regulator on Jetson TX1
arm64: tegra: Correct the UART for Jetson Xavier NX
arm64: tegra: Disable the ACONNECT for Jetson TX2
optee: add writeback to valid memory type
firmware: xilinx: Use hash-table for api feature check
firmware: xilinx: Fix SD DLL node reset issue
soc: fsl: dpio: Get the cpumask through cpumask_of(cpu)
ARM: dts: dra76x: m_can: fix order of clocks
bus: ti-sysc: suppress err msg for timers used as clockevent/source
MAINTAINERS: Remove myself as LPC32xx maintainers
arm64: dts: qcom: clear the warnings caused by empty dma-ranges
arm64: dts: broadcom: clear the warnings caused by empty dma-ranges
ARM: dts: am437x-l4: fix compatible for cpsw switch dt node
arm64: dts: rockchip: Reorder LED triggers from mmc devices on rk3399-roc-pc.
arm64: dts: rockchip: Assign a fixed index to mmc devices on rk3399 boards.
arm64: dts: rockchip: Remove system-power-controller from pmic on Odroid Go Advance
arm64: dts: rockchip: fix NanoPi R2S GMAC clock name
ARM: OMAP2+: Manage MPU state properly for omap_enter_idle_coupled()
...
Not counting TnD, which KVM doesn't currently consider, CSSELR_EL1
can have a maximum value of 0b1101 (13), which corresponds to an
instruction cache at level 7. With CSSELR_MAX set to 12 we can
only select up to cache level 6. Change it to 14.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201126134641.35231-2-drjones@redhat.com
We currently try to emit *.init.rodata.* twice, once in INIT_DATA, and once
in the line immediately following it. As the two section definitions are
identical, the latter is redundant and can be dropped.
This patch drops the redundant *.init.rodata.* section definition.
Signed-off-by: Youling Tang <tangyouling@loongson.cn>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/1605750340-910-1-git-send-email-tangyouling@loongson.cn
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- Fix alignment of the new HYP sections
- Fix GICR_TYPER access from userspace
S390:
- do not reset the global diag318 data for per-cpu reset
- do not mark memory as protected too early
- fix for destroy page ultravisor call
x86:
- fix for SEV debugging
- fix incorrect return code
- fix for "noapic" with PIC in userspace and LAPIC in kernel
- fix for 5-level paging
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl/BKpQUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroPrZgf+Jdw1ONU5hFLl5Xz2YneVppqMr3nh
X/Nr/dGzP+ve2FPNgkMotwqOWb/6jwKYKbliB2Q6fS51/7MiV7TDizna8ZpzEn12
M0/NMWtW7Luq7yTTnXUhClG4QfRvn90EaflxUYxCBSRRhDleJ9sCl4Ga5b1fDIdQ
AeDdqJV4ElCGUrPM1my4vemrbFeiiEeDeWZvb6TP5LlJS+EDZeehk9zEAB7PFwAu
oX3O8WUbRxRYakZR1PPIn8e0qh2zaVDFUk/sZKJLOCCPx2UnOErf3jV6rQEMeSPC
5aOspfq+gI3jukufdyNxcKxRSj8Jw63f0vDaUgd4H71dsG390gM6onQiQg==
=IyC5
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Fix alignment of the new HYP sections
- Fix GICR_TYPER access from userspace
S390:
- do not reset the global diag318 data for per-cpu reset
- do not mark memory as protected too early
- fix for destroy page ultravisor call
x86:
- fix for SEV debugging
- fix incorrect return code
- fix for 'noapic' with PIC in userspace and LAPIC in kernel
- fix for 5-level paging"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: x86/mmu: Fix get_mmio_spte() on CPUs supporting 5-level PT
KVM: x86: Fix split-irqchip vs interrupt injection window request
KVM: x86: handle !lapic_in_kernel case in kvm_cpu_*_extint
MAINTAINERS: Update email address for Sean Christopherson
MAINTAINERS: add uv.c also to KVM/s390
s390/uv: handle destroy page legacy interface
KVM: arm64: vgic-v3: Drop the reporting of GICR_TYPER.Last for userspace
KVM: SVM: fix error return code in svm_create_vcpu()
KVM: SVM: Fix offset computation bug in __sev_dbg_decrypt().
KVM: arm64: Correctly align nVHE percpu data
KVM: s390: remove diag318 reset code
KVM: s390: pv: Mark mm as protected after the set secure parameters and improve cleanup
__extended_idmap_trampoline() was removed a long time ago by
3421e9d88d ("arm64: KVM: Simplify HYP init/teardown") so remove the
unused function prototype.
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201118194402.2892-4-will@kernel.org
kvm_arch_vm_ioctl_check_extension() is only called from
kvm_vm_ioctl_check_extension(), so we can inline it and remove the extra
function.
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201118194402.2892-3-will@kernel.org
'struct kvm_arch_memory_slot' isn't part of the user ABI, so move it out
of the uapi/ headers in case we start using it in future and accidentally
back ourselves into a corner.
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201118194402.2892-2-will@kernel.org
- Fix kerneldoc warnings generated by ACPI IORT code
- Fix pte_accessible() so that access flag is ignored
- Fix missing header #include
- Fix loss of software dirty bit across pte_wrprotect() when HW DBM is enabled
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl/A4moQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNKhtB/4kdY/Do6h8ivkVNy1oId9mWSHrk9HwoEmS
wFvyTIuyhaS2NlNW2/9V662e+wWhzv0ULkDu6aSVsnuw88b1yz1X2ytuh/t8beMJ
PZGWO9UUuVuf+YjcaI7ygppXHILQWdau8eyOVMTciMOYYZRdIqex8WPApxpATRO4
7TphGUuo0IH0GGwq4u6JhPrT0Ihr9txWnvqnM8+fP/y3IbFncH+GKjxZq0k0BwcK
1fkIINwRFHmvkPouPyRPzE6DBudIlHPMGS68CXJV5/T4+JQ5bjc/bmAm8AYVVgip
xSUeKg/x7AMF/8vho0pnvxAqh0FF6c370EjiKBk6AIGNJhjdROxt
=e2/i
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The main changes are relating to our handling of access/dirty bits,
where our low-level page-table helpers could lead to stale young
mappings and loss of the dirty bit in some cases (the latter has not
been observed in practice, but could happen when clearing "soft-dirty"
if we enabled that). These were posted as part of a larger series, but
the rest of that is less urgent and needs a v2 which I'll get to
shortly.
In other news, we've now got a set of fixes to resolve the
lockdep/tracing problems that have been plaguing us for a while, but
they're still a bit "fresh" and I plan to send them to you next week
after we've got some more confidence in them (although initial CI
results look good).
Summary:
- Fix kerneldoc warnings generated by ACPI IORT code
- Fix pte_accessible() so that access flag is ignored
- Fix missing header #include
- Fix loss of software dirty bit across pte_wrprotect() when HW DBM
is enabled"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: pgtable: Ensure dirty bit is preserved across pte_wrprotect()
arm64: pgtable: Fix pte_accessible()
ACPI/IORT: Fix doc warnings in iort.c
arm64/fpsimd: add <asm/insn.h> to <asm/kprobes.h> to fix fpsimd build
Provide support for additional kernel command line parameters to be
concatenated onto the end of the command line provided by the
bootloader. Additional parameters are specified in the CONFIG_CMDLINE
option when CONFIG_CMDLINE_EXTEND is selected, matching other
architectures and leveraging existing support in the FDT and EFI stub
code.
Special care must be taken for the arch-specific nokaslr parsing. Search
the bootargs FDT property and the CONFIG_CMDLINE when
CONFIG_CMDLINE_EXTEND is in use.
There are a couple of known use cases for this feature:
1) Switching between stable and development kernel versions, where one
of the versions benefits from additional command line parameters,
such as debugging options.
2) Specifying additional command line parameters, for additional tuning
or debugging, when the bootloader does not offer an interactive mode.
Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Link: https://lore.kernel.org/r/20200921191557.350256-3-tyhicks@linux.microsoft.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Don't ask for *the* command line string to search for "nokaslr" in
kaslr_early_init(). Instead, tell a helper function to search all the
appropriate command line strings for "nokaslr" and return the result.
This paves the way for searching multiple command line strings without
having to concatenate the strings in early init.
Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Link: https://lore.kernel.org/r/20200921191557.350256-2-tyhicks@linux.microsoft.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
These changes are mostly minor fixes across the board, but they also
enable PMUs on Tegra186 and enable SATA support on Jetson TX2.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAl/BDqATHHRyZWRpbmdA
bnZpZGlhLmNvbQAKCRDdI6zXfz6zoQIpD/4mRhujv5VQ5HFSOsAsoeMvSsA5qC2P
guM207G04N7ZblwapUiJTLbKiW9fwhgb37wqtC/PgWuU6DkL8qVFbL7YIC3hKUN9
6bVdw+Bx9BtvEPRcX0xkUCwb5AK03UcWlUlZJFosLluLC4ZBr6rxrREhYaeTu+I8
sBGvKgIOeb4cm5hWcw1RhHF3aHk/bsWE++AvqTXasNGMc5oG+1KhdifCOruNFSFv
Z4fjM+t/7SQhKEhhvTm+sFlp6dMSl32L29igc6F4iGpJh4cBY4lRpSpP3rOUVXEu
eIRLOXsfNkLePJiyv4DSGW2Kn1FkRWj4rQ9FBvOf3HQM9z6lZjuK4KAGUomKdJ34
ZOGSVvTAep68FWAleg3y2+s3rpK6MFMB4Fg4mAkW0kZbbXstmq7RGCP+Rji9yk13
RvPwO+XRgVgLq9XB6PNYI4G4rvF4vUjSEPPLSnoaOi2HX8zZf5X1jiIB/T5yQpkF
G8rkMoVttoXY+qdvCiq0mIKA7mgkEWuv103gtBwxdVPkCFzes0PkwXx1LV8YVfrz
JN76/qWtzdivx1sgSx9gcgG7tFb+FmS8b2xfIAm2UJbRyMCUTTXRxfmKMTa3+xBU
+RxHPxrDQ1jBe6pPAJsQrMUUdwZEiAsAF6ZJtWcoaaAoFVkLtdInkG/O/ID4TNkK
IwFLk+fsLtrD/w==
=WWBT
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.11-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Device tree changes for v5.11-rc1
These changes are mostly minor fixes across the board, but they also
enable PMUs on Tegra186 and enable SATA support on Jetson TX2.
* tag 'tegra-for-5.11-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Fix Tegra194 HDA {clock,reset}-names ordering
arm64: tegra: Enable AHCI on Jetson TX2
arm64: tegra: Change order of SATA resets for Tegra132 and Tegra210
arm64: tegra: Add XUSB pad controller interrupt
arm64: tegra: Rename ADMA device nodes for Tegra210
arm64: tegra: Hook up edp interrupt on Tegra132 SOCTHERM
arm64: tegra: Add missing hot temperatures to Tegra210 thermal-zones
arm64: tegra: Add missing gpu-throt-level to Tegra210 soctherm
arm64: tegra: Add missing hot temperatures to Tegra132 thermal-zones
arm64: tegra: Fix DT binding for IO High Voltage entry
arm64: tegra: Fix GIC400 missing GICH/GICV register regions
arm64: tegra: Add missing CPU PMUs on Tegra186
arm64: tegra: Fix Tegra234 VDK node names
arm64: tegra: Wrong AON HSP reg property size
arm64: tegra: Fix USB_VBUS_EN0 regulator on Jetson TX1
arm64: tegra: Correct the UART for Jetson Xavier NX
arm64: tegra: Disable the ACONNECT for Jetson TX2
Link: https://lore.kernel.org/r/20201127144329.124891-5-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- PCIe endpoint support for the R-Car H3 ES2.0+ SoC.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCX8D7wQAKCRCKwlD9ZEnx
cGthAP9Tnhv6LWGL4002pLs2LS/qnPqIhWLjh+o989pKkCEJtAD9GKuzI0+tiSuk
CfPOhZUFUI7eZ99icVBPbc0yamB9UQs=
=lR48
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-dt-for-v5.11-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.11 (take two)
- PCIe endpoint support for the R-Car H3 ES2.0+ SoC.
* tag 'renesas-arm-dt-for-v5.11-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: r8a77951: Add PCIe EP nodes
Link: https://lore.kernel.org/r/20201127132155.77418-2-geert@linux-m68k.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Tegra234 VDK support that was introduced in v5.10-rc1 is now enabled
by default.
-----BEGIN PGP SIGNATURE-----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=KgUW
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.11-arm64-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/defconfig
arm64: tegra: Default configuration changes for v5.11-rc1
The Tegra234 VDK support that was introduced in v5.10-rc1 is now enabled
by default.
* tag 'tegra-for-5.11-arm64-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: defconfig: Enable Tegra234 support
Link: https://lore.kernel.org/r/20201127144329.124891-6-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
MDI_TP_P0 (gpio51) is used by pwm1 and uart2 (uart1 on gpio-header)
MDI_RP_P4 (gpio67) is used by pwm4 and spi1
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20201016204019.2606-3-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
mt7622 only supports 6 pwm-channels so drop pwm7
third pwm (pwm2) is inverted and connected to fan-socket
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20201016204019.2606-2-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
- Fix alignment of the new HYP sections
- Fix GICR_TYPER access from userspace
-----BEGIN PGP SIGNATURE-----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=oova
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-5.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master
KVM/arm64 fixes for v5.10, take #4
- Fix alignment of the new HYP sections
- Fix GICR_TYPER access from userspace
J7200 main_i2c1 is connected to the i2c bus on the CPB marked as main_i2c3
The i2c1 devices on the CPB are _not_ connected to the SoC, they are not
usable with the J7200 SOM.
Correct the expander name from exp4 to exp3 and at the same time add the
line names as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201120073533.24486-3-peter.ujfalusi@ti.com
The J7200 SOM have additional io expander which is used to control several
SOM level muxes to make sure that the correct signals are routed to the
correct pin on the SOM <-> CPB connectors.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201120073533.24486-2-peter.ujfalusi@ti.com
We currently gate the update of the PMU state on the PMU being "ready".
The "ready" state is only set to true when the first vcpu run is
successful, and if it isn't, we never reach the update code.
So the "ready" state is never the right thing to check for, and it
should instead be the presence of the PMU feature, which makes
a bit more sense.
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The handling of traps in access_pmu_evcntr() has a couple of
omminous "else return false;" statements that don't make any sense:
the decoding tree coverse all the registers that trap to this handler,
and returning false implies that we change PC, which we don't.
Get rid of what is evidently dead code.
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
There is no RAZ/WI handling allowed for the PMU registers in the
ARMv8 architecture. Nobody can remember how we cam to the conclusion
that we could do this, but the ARMv8 ARM is pretty clear that we cannot.
Remove the RAZ/WI handling of the PMU system registers when it is
not configured.
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The ARMv8 architecture says that in the absence of FEAT_PMUv3,
all the PMU-related register generate an UNDEF. Let's make
sure that all our PMU handers catch this case by hooking into
check_pmu_access_disabled(), and add checks in a couple of
other places.
Note that we still cannot deliver an exception into the guest
as the offending cases are already caught by the RAZ/WI handling.
But this puts us one step away to architectural compliance.
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
We accept to configure a PMU when a vcpu is created, even if the
HW (or the host) doesn't support it. This results in failures
when attributes get set, which is a bit odd as we should have
failed the vcpu creation the first place.
Move the check to the point where we check the vcpu feature set,
and fail early if we cannot support a PMU. This further simplifies
the attribute handling.
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
We always expose the HW view of PMU in ID_AA64FDR0_EL1.PMUver,
even when the PMU feature is disabled, while the architecture
says that FEAT_PMUv3 not being implemented should result in this
field being zero.
Let's follow the architecture's guidance.
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
When enabling the PMU in kvm_arm_pmu_v3_enable(), KVM returns early if the
PMU flag created is false and skips any other checks. Because PMU emulation
is gated only on the VCPU feature being set, this makes it possible for
userspace to get away with setting the VCPU feature but not doing any
initialization for the PMU. Fix it by returning an error when trying to run
the VCPU if the PMU hasn't been initialized correctly.
The PMU is marked as created only if the interrupt ID has been set when
using an in-kernel irqchip. This means the same check in
kvm_arm_pmu_v3_enable() is redundant, remove it.
Signed-off-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201126144916.164075-1-alexandru.elisei@arm.com
There are a number of places where we check for the KVM_ARM_VCPU_PMU_V3
feature. Wrap this check into a new kvm_vcpu_has_pmu(), and use
it at the existing locations.
No functional change.
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Registers x0/x1 get repeateadly pushed and poped during a host
HVC call. Instead, leave the registers on the stack, trading
a store instruction on the fast path for an add on the slow path.
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Move the setting of SSBS directly into the HVC handler, using
the C helpers rather than the inline asssembly code.
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Directly using the kimage_voffset variable is fine for now, but
will become more problematic as we start distrusting EL1.
Instead, patch the kimage_voffset into the HYP text, ensuring
we don't have to load an untrusted value later on.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Add pwm to mt8183 and backlight to mt8183-kukui.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20201124041253.4181273-1-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The SMI (Smart Multimedia Interface) Common is a bridge between the m4u
(Multimedia Memory Management Unit) and the Multimedia HW. This block is
needed to support different multimedia features, like display, video
decode, and camera. Also is needed to control the power domains of such
HW blocks.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20201030113622.201188-13-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The pumpkin board is made by Gossamer Engineering and is using
a MediaTek SoC. The board currently comes in two available version:
MT8516 SoC and MT8167 SoC.
The board provides the following IOs: eMMC, NAND, SD card, USB type-A,
Ethernet, Wi-Fi, Bluetooth, Audio (jack out, 2 PDM port, 1 analog in),
serial over USB, HDMI, DSI, CSI, and an expansion header.
The board can be powered by battery and/or via a USB Type-C port and
is using a PMIC MT6392.
The eMMC and NAND are sharing pins and cannot be used together.
This commit is adding the basic boot support for the Pumpkin MT8167
board.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Link: https://lore.kernel.org/r/20201027194816.1227654-3-fparent@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The MT8167 SoC provides the following peripherals: GPIO, UART, USB2,
SPI, eMMC, SDIO, NAND, Flash, ADC, I2C, PWM, TImers, IR, Ethernet,
Audio (I2S, SPDIF, TDM, HDMI), HDMI, DSI, CSI, MDP (Multimedia Data
Path), Video encoding (H.264), Video Decoding (H.264, VP8).
The MT8167 is compatible with MT8516 but provides multimedia IPs to it.
This commit is just adding the basic dtsi file with the support of the
following IOs: GPIO, Clocks.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Link: https://lore.kernel.org/r/20201027194816.1227654-2-fparent@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
- Cleanups of the hisilicon DTS to align with the dtschema. All of them do not
have any functional effect except passing dtschema checks or dtc W=2 builds.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pM5V
-----END PGP SIGNATURE-----
Merge tag 'hisi-arm64-dt-for-5.11' of git://github.com/hisilicon/linux-hisi into arm/dt
ARM64: DT: Hisilicon ARM64 DT updates for 5.11
- Cleanups of the hisilicon DTS to align with the dtschema. All of them do not
have any functional effect except passing dtschema checks or dtc W=2 builds.
* tag 'hisi-arm64-dt-for-5.11' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hisilicon: Use generic "ngpios" rather than "snps,nr-gpios"
arm64: dts: hi3660: Harmonize DWC USB3 DT nodes name
arm64: dts: hisilicon: list all clocks required by snps-dw-apb-uart.yaml
arm64: dts: hisilicon: list all clocks required by pl011.yaml
arm64: dts: hisilicon: list all clocks required by spi-pl022.yaml
arm64: dts: hisilicon: normalize the node name of the UART devices
arm64: dts: hisilicon: normalize the node name of the usb devices
arm64: dts: hisilicon: normalize the node name of the SMMU devices
arm64: dts: hisilicon: place clock-names "biu" before "ciu"
arm64: dts: hisilicon: remove unused property pinctrl-names
arm64: dts: hisilicon: write the values of property-units into a uint32 array
arm64: dts: hisilicon: separate each group of data in the property "reg"
arm64: dts: hisilicon: normalize the node name of the ITS devices
Link: https://lore.kernel.org/r/5FBDC416.5060008@hisilicon.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This contains a couple of fixes to device trees. Among other things,
this restores suspend/resume on Jetson TX2 and makes USB OTG work on
Jetson TX1.
-----BEGIN PGP SIGNATURE-----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=+GCH
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.10-arm64-dt-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/fixes
arm64: tegra: Device tree fixes for v5.10-rc6
This contains a couple of fixes to device trees. Among other things,
this restores suspend/resume on Jetson TX2 and makes USB OTG work on
Jetson TX1.
* tag 'tegra-for-5.10-arm64-dt-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Fix Tegra234 VDK node names
arm64: tegra: Wrong AON HSP reg property size
arm64: tegra: Fix USB_VBUS_EN0 regulator on Jetson TX1
arm64: tegra: Correct the UART for Jetson Xavier NX
arm64: tegra: Disable the ACONNECT for Jetson TX2
Link: https://lore.kernel.org/r/20201125170306.1095734-1-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix SD dll reset issue by using proper macro
- Fix PM feature checking for Xilinx Versal SoC
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX70VSQAKCRDKSWXLKUoM
ISZ+AJ9IkZ3rto9BOpbuSUu2mZSG12hSBACgnY0S3UCCZ4G4RLbGrFPzvGUKTuM=
=SwId
-----END PGP SIGNATURE-----
Merge tag 'zynqmp-soc-fixes-for-v5.10-rc6' of https://github.com/Xilinx/linux-xlnx into arm/fixes
arm64: soc: ZynqMP SoC fixes for v5.10-rc6
- Fix SD dll reset issue by using proper macro
- Fix PM feature checking for Xilinx Versal SoC
* tag 'zynqmp-soc-fixes-for-v5.10-rc6' of https://github.com/Xilinx/linux-xlnx: (337 commits)
firmware: xilinx: Use hash-table for api feature check
firmware: xilinx: Fix SD DLL node reset issue
Linux 5.10-rc4
kvm: mmu: fix is_tdp_mmu_check when the TDP MMU is not in use
afs: Fix afs_write_end() when called with copied == 0 [ver #3]
ocfs2: initialize ip_next_orphan
panic: don't dump stack twice on warn
hugetlbfs: fix anon huge page migration race
mm: memcontrol: fix missing wakeup polling thread
kernel/watchdog: fix watchdog_allowed_mask not used warning
reboot: fix overflow parsing reboot cpu number
Revert "kernel/reboot.c: convert simple_strtoul to kstrtoint"
compiler.h: fix barrier_data() on clang
mm/gup: use unpin_user_pages() in __gup_longterm_locked()
mm/slub: fix panic in slab_alloc_node()
mailmap: fix entry for Dmitry Baryshkov/Eremin-Solenikov
mm/vmscan: fix NR_ISOLATED_FILE corruption on 64-bit
mm/compaction: stop isolation if too many pages are isolated and we have pages to migrate
mm/compaction: count pages and stop correctly during page isolation
drm/nouveau/kms/nv50-: Use atomic encoder callbacks everywhere
...
Link: https://lore.kernel.org/r/fd5ab967-f3cf-95fb-7947-5477ff85f97e@monstr.eu
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use GIC_SPI rather than 0 in the specifiers for the two ARM GIC
interrupts used by IPA.
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20201126015457.6557-4-elder@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Use GIC_SPI rather than 0 in the specifiers for the two ARM GIC
interrupts used by IPA.
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20201126015457.6557-3-elder@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Recently we learned that Android and Windows firmware don't seem to
like using 3 as an iommu mask value for IPA. A simple fix was to
specify exactly the streams needed explicitly, rather than implying
a range with the mask. Make the same change for the SC7180 platform.
See also:
https://lore.kernel.org/linux-arm-msm/20201123052305.157686-1-bjorn.andersson@linaro.org/
Fixes: d82fade846 ("arm64: dts: qcom: sc7180: add IPA information")
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20201126015457.6557-2-elder@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
As per the HDA binding doc reorder {clock,reset}-names entries for
Tegra194. This also serves as a preparation for converting existing
binding doc to json-schema.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra AHCI dt-binding doc is converted from text based to yaml based.
dtbs_check valdiation strictly follows reset-names order specified
in yaml dt-binding.
Tegra124 thru Tegra210 has 3 resets sata, sata-oob and sata-cold.
Tegra186 has 2 resets sata and sata-cold.
This patch changes order of SATA resets to maintain proper resets
order for commonly available resets across Tegra124 thru Tegra186
for dtbs_check to pass.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit adds "interrupts" property to Tegra210/Tegra186/Tegra194
XUSB PADCTL node. XUSB PADCTL interrupt will be raised when USB wake
event happens. This is required for supporting XUSB host controller
ELPG.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The trogdor design has two options for supplying the 'pp3300_hub' power
rail, it can be supplied by 'pp3300_l7c' or 'pp3300_a'. The 'pp3300_a'
path includes a load switch that can be controlled through GPIO84.
Initially trogdor boards used 'pp3300_l7c' to power the USB hub, newer
revisions (will) use 'pp3300_a' as supply for 'pp3300_hub'.
Add a DT node for the 'pp3300_a' path and a pinctrl entry for the GPIO.
Make this path the default and keep trogdor rev1, lazor rev0 and rev1
on 'pp3300_l7c'. These earlier revisions also allocated the GPIO to the
purpose of controlling the power switch, so there is no need to limit
the pinctrl config to newer revisions. Remove the platform-wide
'always/boot-on' properties from 'pp3300_l7c' and add them to the
boards that use this supply. Also delete the 'always/boot-on'
properties of 'pp3300_hub' for these boards.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201124164714.v4.1.I0ed4abdd2b2916fbedf76be254bc3457fb8b9655@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add ARCH_BCM4908 config that can be used for compiling DTS files.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
They don't descibe hardware fully yet but it's enough to boot a system.
Some missing blocks:
1. PMC (Power Management Controller?)
2. Ethernet
3. Crypto
4. Thermal
Asus DTS is missing defining full NAND partitions layout and buttons.
Further changes will fill those gaps as soon as required bindings will
be found / tested / added.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
With the recent feature added to enable perf events to use pseudo NMIs
as interrupts on platforms which support GICv3 or later, its now been
possible to enable hard lockup detector (or NMI watchdog) on arm64
platforms. So enable corresponding support.
One thing to note here is that normally lockup detector is initialized
just after the early initcalls but PMU on arm64 comes up much later as
device_initcall(). So we need to re-initialize lockup detection once
PMU has been initialized.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Acked-by: Alexandru Elisei <alexandru.elisei@arm.com>
Link: https://lore.kernel.org/r/1602060704-10921-1-git-send-email-sumit.garg@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
DMA device nodes should follow regex pattern of "^dma-controller(@.*)?$".
This is a preparatory patch to use YAML doc format for ADMA.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For some reason this was never hooked up. Do it now so that over-current
interrupts can be logged.
Reported-by: Nicolas Chauvet <kwizart@gmail.com>
Suggested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
According to dmesg, thermal-zones for mem and cpu are missing hot
temperatures properties.
throttrip: pll: missing hot temperature
...
throttrip: mem: missing hot temperature
...
Adding them will clear the messages.
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Jetson TX1 the following message can be seen:
tegra_soctherm 700e2000.thermal-sensor: throttle-cfg: heavy: no throt prop or invalid prop
This patch will fix the invalid prop issue according to the binding.
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
According to dmesg, thermal-zones for mem and cpu are missing hot
temperatures properties.
throttrip: pll: missing hot temperature
...
throttrip: mem: missing hot temperature
...
Adding them will clear the messages.
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fix the device-tree entry that represents I/O High Voltage property
by replacing 'nvidia,io-high-voltage' with 'nvidia,io-hv' as the former
entry is deprecated.
Fixes: dbb72e2c30 ("arm64: tegra: Add configuration for PCIe C5 sideband signals")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
GIC400 has full support for virtualization, and yet the tegra186
DT doesn't expose the GICH/GICV regions (despite exposing the
maintenance interrupt that only makes sense for virtualization).
Add the missing regions, based on the hunch that the HW doesn't
use the CPU build-in interfaces, but instead the external ones
provided by the GIC. KVM's virtual GIC now works with this change.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the description of CPU PMUs for both the Denver and A57 clusters,
which enables the perf subsystem.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the device-tree board file was added for the Tegra234 VDK simulator
it incorrectly used the names 'cbb' and 'sdhci' instead of 'bus' and
'mmc', respectively. The names 'bus' and 'mmc' are required by the
device-tree json-schema validation tools. Therefore, fix this by
renaming these nodes accordingly.
Fixes: 639448912b ("arm64: tegra: Initial Tegra234 VDK support")
Reported-by: Ashish Singhal <ashishsingha@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The AON HSP node's "reg" property size 0xa0000 will overlap with other
resources. This patch fixes that wrong value with correct size 0x90000.
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Dipen Patel <dipenp@nvidia.com>
Fixes: a38570c22e ("arm64: tegra: Add nodes for TCU on Tegra194")
Signed-off-by: Thierry Reding <treding@nvidia.com>
USB host mode is broken on the OTG port of Jetson TX1 platform because
the USB_VBUS_EN0 regulator (regulator@11) is being overwritten by the
vdd-cam-1v2 regulator. This commit rearranges USB_VBUS_EN0 to be
regulator@14.
Fixes: 257c8047be ("arm64: tegra: jetson-tx1: Add camera supplies")
Cc: stable@vger.kernel.org
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Jetson Xavier NX board routes UARTA to the 40-pin header and UARTC
to a 12-pin debug header. The UARTs can be used by either the Tegra
Combined UART (TCU) driver or the Tegra 8250 driver. By default, the
TCU will use UARTC on Jetson Xavier NX. Currently, device-tree for
Xavier NX enables the TCU and the Tegra 8250 node for UARTC. Fix this
by disabling the Tegra 8250 node for UARTC and enabling the Tegra 8250
node for UARTA.
Fixes: 3f9efbbe57 ("arm64: tegra: Add support for Jetson Xavier NX")
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit ff4c371d2b ("arm64: defconfig: Build ADMA and ACONNECT driver")
enable the Tegra ADMA and ACONNECT drivers and this is causing resume
from system suspend to fail on Jetson TX2. Resume is failing because the
ACONNECT driver is being resumed before the BPMP driver, and the ACONNECT
driver is attempting to power on a power-domain that is provided by the
BPMP. While a proper fix for the resume sequencing problem is identified,
disable the ACONNECT for Jetson TX2 temporarily to avoid breaking system
suspend.
Please note that ACONNECT driver is used by the Audio Processing Engine
(APE) on Tegra, but because there is no mainline support for APE on
Jetson TX2 currently, disabling the ACONNECT does not disable any useful
feature at the moment.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
DT schema is checking tuples which should be properly separated. The patch
is doing this separation to avoid the following warning:
..yaml: axi: pcie@fd0e0000:ranges: [[33554432, 0, 3758096384, 0,
3758096384, 0, 268435456, 1124073472, 6, 0, 6, 0, 2, 0]] is not valid under
any of the given schemas (Possible causes of the failure):
...dt.yaml: axi: pcie@fd0e0000:ranges: True was expected
...dt.yaml: axi: pcie@fd0e0000:ranges:0: [33554432, 0, 3758096384, 0,
3758096384, 0, 268435456, 1124073472, 6, 0, 6, 0, 2, 0] is too long
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/f59a63d8cb941592de6d2dee8afa6f120b2e40c8.1601379794.git.michal.simek@xilinx.com
The reason for this change is that after change from amba to axi U-Boot
started to show error like:
Unable to update property /axi/ethernet@ff0e0000:mac-address, err=FDT_ERR_NOTFOUND
Unable to update property /axi/ethernet@ff0e0000:local-mac-address, err=FDT_ERR_NOTFOUND
The reason is implementation in fdt_nodename_eq_() which is taken from dtc
to the kernel and to the U-Boot. Especially DTC commit d2a9da045897 ("libfdt:
Make unit address optional for finding nodes") which is in DTC from 2007.
The part of commit description is
" This is contrary to traditional OF-like finddevice() behaviour, which
allows the unit address to be omitted (which is useful when the device
name is unambiguous without the address)."
The kernel commit dfff9066e6 ("arm64: dts: zynqmp: Rename buses to be
align with simple-bus yaml") changed amba-apu/amba to axi@0/axi but
fdt_nodename_eq_() detects /axi/ as match for /axi@0/ because of commit
above.
That's why it easier to fix one DT inside the kernel by moving GIC node
from own bus to generic axi bus as is done by others SoCs. This will avoid
incorrect match because the unit address is omitted.
Reported-by: Paul Thomas <pthomas8589@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/f767fe007e446a2299fda9905e75b723c650a424.1605021644.git.michal.simek@xilinx.com
The PON block in the PMIC provides, among other things, support for
"reboot reason", power key and reset "key" handling. Let's enable the
driver for this block.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201125023831.99774-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add DDR/L3 bandwidth votes for the pro variant of SC7180 SoC, as it support
frequencies upto 2.5 GHz.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/1606198876-3515-2-git-send-email-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tweak the DDR/L3 bandwidth votes on the lite variant of the SC7180 SoC
since the gold cores only support frequencies upto 2.1 GHz.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/1606198876-3515-1-git-send-email-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Trogdor has a thermistor to monitor the temperature of the charger IC.
Add the ADC (monitor) nodes and a thermal zone for this thermistor.
Signed-off-by: Antony Wang <antony_wang@compal.corp-partner.google.com>
[mka: tweaked commit message]
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20201030084840.1.If389f211a8532b83095ff8c66ec181424440f8d6@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add ADC_TM peripheral definitions for PM6150 and PM6150L. Add
ADC peripheral definition for PM6150l, which is needed for ADC_TM.
Signed-off-by: Jishnu Prakash <jprakash@codeaurora.org>
Link: https://lore.kernel.org/r/1602160825-10414-2-git-send-email-jprakash@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Android and Windows firmware does not accept the use of 3 as a mask
to cover the IPA streams. But with 0x721 being related to WiFi and 0x723
being unsed the mapping can be reduced to just cover 0x720 and 0x722,
which is accepted.
Acked-by: Alex Elder <elder@linaro.org>
Tested-by: Alex Elder <elder@linaro.org>
Fixes: e9e89c45bf ("arm64: dts: sdm845: add IPA iommus property")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201123052305.157686-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We call arch_cpu_idle() with RCU disabled, but then use
local_irq_{en,dis}able(), which invokes tracing, which relies on RCU.
Switch all arch_cpu_idle() implementations to use
raw_local_irq_{en,dis}able() and carefully manage the
lockdep,rcu,tracing state like we do in entry.
(XXX: we really should change arch_cpu_idle() to not return with
interrupts enabled)
Reported-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lkml.kernel.org/r/20201120114925.594122626@infradead.org
Point the various remoteprocs of SM8150 MTP to a place with the platform
specific firmware.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201121055603.582281-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The SMMU that sits in front of the QUP needs to be programmed properly
so that the i2c geni driver can allocate DMA descriptors. Failure to do
this leads to faults when using devices such as an i2c touchscreen where
the transaction is larger than 32 bytes and we use a DMA buffer.
arm-smmu 15000000.iommu: Unexpected global fault, this could be serious
arm-smmu 15000000.iommu: GFSR 0x00000002, GFSYNR0 0x00000002, GFSYNR1 0x000006c0, GFSYNR2 0x00000000
Add the right SID and mask so this works.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Caleb Connolly <caleb@connolly.tech>
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
[bjorn: Define for second QUP as well, be more specific in sdm845.dtsi]
Link: https://lore.kernel.org/r/20201122034149.626045-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This is to remove similar errors as below:
OF: /.../gpio-port@0: could not find phandle
Commit 7569486d79 ("gpio: dwapb: Add ngpios DT-property support")
explained the reason of above errors well and added the generic
"ngpios" property, let's use it.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
In accordance with the DWC USB3 bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "snps,dwc3"-compatible nodes are correctly
named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The snps,dw-apb-uart binding need to specify two clocks: "baudclk",
"apb_pclk". But only "apb_pclk" is specified now. Because the driver
preferentially matches the first clock. Otherwise, it matches the second
clock instead of both clocks. So both of them use the same clock don't
change the function.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The arm,pl011 binding need to specify two clocks: "uartclk", "apb_pclk".
But only "apb_pclk" is specified now. Because the driver preferentially
matches the first clock. Otherwise, it matches the second clock instead
of both clocks. So both of them use the same clock don't change the
function.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The arm,pl022 binding need to specify two clocks: "sspclk", "apb_pclk".
But only "apb_pclk" is specified now. Because the driver preferentially
matches the first clock. Otherwise, it matches the second clock instead
of both clocks. So both of them use the same clock don't change the
function.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Change the node name of the UART devices to match
"^serial(@[0-9a-f,]+)*$".
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Change the node name of the usb devices to match "^usb(@.*)?". These errors
are detected by generic-ehci.yaml and generic-ohci.yaml.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Change the node name of the SMMU devices to match "^iommu@[0-9a-f]*".
Otherwise, the errors similar to the following will be reported by
arm,smmu-v3.yaml.
smmu_pcie: $nodename:0: 'smmu_pcie' does not match '^iommu@[0-9a-f]*'
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Look at the clock-names schema defined in synopsys-dw-mshc.yaml:
clock-names:
items:
- const: biu
- const: ciu
The "biu" needs to be placed before the "ciu".
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
uart1 and uart5 are not used as pinctrl, so the property "pinctrl-names"
can be deleted. In fact, the property "pinctrl-names" depends on the
property "pinctrl-0". So the errors similar to the following will be
reported by pinctrl-consumer.yaml.
serial@fdf00000: 'pinctrl-0' is a dependency of 'pinctrl-names'
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Use <> to separate the values of property-units will be treated as
multiple arrays. The errors similar to the following will be reported by
property-units.yaml.
ufs@ff3c0000: freq-table-hz: [[0, 0], [0, 0]] is too long
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Do not write the "reg" of multiple groups of data into a uint32 array,
use <> to separate them. Otherwise, the errors similar to the following
will be reported by reg.yaml.
soc: dsa@c7000000:reg:0: [0, 3305111552, 0, 8978432, 0, 3338665984, 0, \
6291456] is too long
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Change the node name of the ITS devices to match
"^(msi-controller|gic-its|interrupt-controller)@[0-9a-f]+$". Although
"interrupt-controller" is allowed, but "msi-controller" is preferred.
Otherwise, "interrupt-controller@b7000000: False schema does not allow"
will be reported by arm,gic-v3.yaml.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The uart2 node has been renamed, apply the change to sm8250-hdk dts too so
that serial output works.
Fixes: 91ed0e90fc ("arm64: dts: qcom: add sm8250 hdk dts")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20201123143538.14198-1-jonathan@marek.ca
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
all ordering, a fix to make the Odroig Go Advance actually power down
and using the correct clock name on the NanoPi R2S.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAl+6aAkQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgZ6aB/4zVEcf7LYe6RMdV8DCaDHSPK2V8uYOifu/
Z8BaCJujiED249NI0NzvbZqrcuSjssxOSi4Y4kNCytPODs1+4wLVgG0f2xC2k38X
o0ofroN68lueSdhw4PZ9216w9scZpo/POLC7LLWR6kzlKGKv5Bj4w9UAq6cqqSMk
9FCwSyCxKm3yuYaWz/iJLJfC1oWRZ6qMvzjtXfdDT8bMFhLUZh9UOoWGeJP7CPIQ
nGu1WWVXWsda4UN7hwirGkApp65yK8asubekznBb2vw9Rr2A3bBuCqDdyOOOim3E
qxeLLGiObNfM6t0m5Pp+PfWPwqyn864LGUBBQ3b5zz7l2wjMh5i8
=/LkX
-----END PGP SIGNATURE-----
Merge tag 'v5.10-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
Fixed ordering for MMC devices on rk3399, due to a mmc change jumbling
all ordering, a fix to make the Odroig Go Advance actually power down
and using the correct clock name on the NanoPi R2S.
* tag 'v5.10-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Reorder LED triggers from mmc devices on rk3399-roc-pc.
arm64: dts: rockchip: Assign a fixed index to mmc devices on rk3399 boards.
arm64: dts: rockchip: Remove system-power-controller from pmic on Odroid Go Advance
arm64: dts: rockchip: fix NanoPi R2S GMAC clock name
Link: https://lore.kernel.org/r/11641389.O9o76ZdvQC@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
With hardware dirty bit management, calling pte_wrprotect() on a writable,
dirty PTE will lose the dirty state and return a read-only, clean entry.
Move the logic from ptep_set_wrprotect() into pte_wrprotect() to ensure that
the dirty bit is preserved for writable entries, as this is required for
soft-dirty bit management if we enable it in the future.
Cc: <stable@vger.kernel.org>
Fixes: 2f4b829c62 ("arm64: Add support for hardware updates of the access and dirty pte bits")
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20201120143557.6715-3-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
pte_accessible() is used by ptep_clear_flush() to figure out whether TLB
invalidation is necessary when unmapping pages for reclaim. Although our
implementation is correct according to the architecture, returning true
only for valid, young ptes in the absence of racing page-table
modifications, this is in fact flawed due to lazy invalidation of old
ptes in ptep_clear_flush_young() where we elide the expensive DSB
instruction for completing the TLB invalidation.
Rather than penalise the aging path, adjust pte_accessible() to return
true for any valid pte, even if the access flag is cleared.
Cc: <stable@vger.kernel.org>
Fixes: 76c714be0e ("arm64: pgtable: implement pte_accessible()")
Reported-by: Yu Zhao <yuzhao@google.com>
Acked-by: Yu Zhao <yuzhao@google.com>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20201120143557.6715-2-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
- Touch screen and OV5640 camera support for the iWave RainboW Qseven
board (G21D), and its camera expansion board,
- Support for the AISTARVISION MIPI Adapter V2.1 board connected to
HiHope RZ/G2 boards,
- SPI (MSIOF) support for the R-Car M3-W+ SoC,
- Digital Radio Interface (DRIF) support for the R-Car M3-N SoC,
- Initial support for the R-Car M3-W+ ULCB/Kingfisher board combo,
- Minor fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCX66VTQAKCRCKwlD9ZEnx
cFhnAP9W9Jp5o/gp9JQ+Y2Js3xMDD9JngTYRQ+9x4qu2HTf0AAEAjfSzb0T2ub/x
HaW5LisNk1LZNp09+9ugw/nNZxp45AQ=
=QdJ8
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-dt-for-v5.11-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.11
- Touch screen and OV5640 camera support for the iWave RainboW Qseven
board (G21D), and its camera expansion board,
- Support for the AISTARVISION MIPI Adapter V2.1 board connected to
HiHope RZ/G2 boards,
- SPI (MSIOF) support for the R-Car M3-W+ SoC,
- Digital Radio Interface (DRIF) support for the R-Car M3-N SoC,
- Initial support for the R-Car M3-W+ ULCB/Kingfisher board combo,
- Minor fixes and improvements.
* tag 'renesas-arm-dt-for-v5.11-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: hihope-rev4: Add a comment explaining switch SW2404
arm64: dts: renesas: r8a77961: ulcb-kf: Initial device tree
arm64: dts: renesas: r8a77961: Add CAN{0,1} placeholder nodes
arm64: dts: renesas: beacon-renesom-baseboard: Move connector node out of hd3ss3220 device
arm64: dts: renesas: cat874: Move connector node out of hd3ss3220 device
arm64: dts: renesas: rzg2: Convert EtherAVB to explicit delay handling
arm64: dts: renesas: rcar-gen3: Convert EtherAVB to explicit delay handling
arm64: dts: renesas: r8a77965: Add DRIF support
arm64: dts: renesas: Add support for MIPI Adapter V2.1 connected to HiHope RZ/G2N
arm64: dts: renesas: Add support for MIPI Adapter V2.1 connected to HiHope RZ/G2M
arm64: dts: renesas: Add support for MIPI Adapter V2.1 connected to HiHope RZ/G2H
arm64: dts: renesas: aistarvision-mipi-adapter-2.1: Add parent macro for each sensor
arm64: dts: renesas: cat875: Remove rxc-skew-ps from ethernet-phy node
arm64: dts: renesas: hihope-rzg2-ex: Drop rxc-skew-ps from ethernet-phy node
ARM: dts: r8a7742-iwg21d-q7-dbcm-ca: Enable VIN instances
arm64: dts: renesas: r8a77961: Add MSIOF nodes
arm64: dts: renesas: Align GPIO hog names with dtschema
ARM: dts: r8a7742-iwg21d-q7: Add LCD support
Link: https://lore.kernel.org/r/20201113150854.3923885-3-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Enable support for the new R-Car V3U SoC in the arm64 defconfig,
- Refresh shmobile_defconfig for v5.10-rc1.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCX66RqgAKCRCKwlD9ZEnx
cLC5AP493HI4gYGzpdkwikaOR6sMM5iwI0v3n1AYcuw79Ep11gEAyEg0DpLMAOG8
aHDYqSv6Zo10pYjbHBJRwYRrOJMarw4=
=eio1
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-defconfig-for-v5.11-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/defconfig
Renesas ARM defconfig updates for v5.11
- Enable support for the new R-Car V3U SoC in the arm64 defconfig,
- Refresh shmobile_defconfig for v5.10-rc1.
* tag 'renesas-arm-defconfig-for-v5.11-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: defconfig: Enable R8A779A0 SoC
ARM: shmobile: defconfig: Refresh for v5.10-rc1
Link: https://lore.kernel.org/r/20201113150854.3923885-2-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Adding <asm/exception.h> brought in <asm/kprobes.h> which uses
<asm/probes.h>, which uses 'pstate_check_t' so the latter needs to
#include <asm/insn.h> for this typedef.
Fixes this build error:
In file included from arch/arm64/include/asm/kprobes.h:24,
from arch/arm64/include/asm/exception.h:11,
from arch/arm64/kernel/fpsimd.c:35:
arch/arm64/include/asm/probes.h:16:2: error: unknown type name 'pstate_check_t'
16 | pstate_check_t *pstate_cc;
Fixes: c6b90d5cf6 ("arm64/fpsimd: Fix missing-prototypes in fpsimd.c")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Will Deacon <will@kernel.org>
Cc: Tian Tao <tiantao6@hisilicon.com>
Link: https://lore.kernel.org/r/20201123044510.9942-1-rdunlap@infradead.org
Signed-off-by: Will Deacon <will@kernel.org>
irq_cpustat_t is exactly the same as the asm-generic one. Define
ack_bad_irq so the generic header does not emit the generic version of it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201113141733.392015387@linutronix.de
Commit 22337b9102 ("arm64: dts: qcom: sc7180: Changed polling mode
in Thermal-zones node") sets both 'polling-delay' and
'polling-delay-passive' to zero with the rationale that TSENS interrupts
are enabled. A TSENS interrupt fires when the temperature of a thermal
zone reaches a trip point, which makes regular polling below the passive
trip point temperature unnecessary. However the situation is different
when passive cooling is active, regular polling is still needed to
trigger a periodic evaluation of the thermal zone by the thermal governor.
Change 'polling-delay-passive' back to the original value of 250 ms.
Commit 2315ae70af ("arm64: dts: qcom: sc7180: Add gpu cooling
support") recently changed the value for the GPU thermal zones from
zero to 100 ms, also set it to 250 ms for uniformity. If some zones
really need different values these can be changed in dedicated patches.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Fixes: 22337b9102 ("arm64: dts: qcom: sc7180: Changed polling mode in Thermal-zones node")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20201111120334.1.Ifc04ea235c3c370e3b21ec3b4d5dead83cc403b4@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Some versions of the firmware leave i2c gpios in a wrong state.
Add pinctrl that disables pin bias since external pull-up resistors
are present.
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Fixes: 1329c1ab07 ("arm64: dts: qcom: Add device tree for Samsung Galaxy A3U/A5U")
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Link: https://lore.kernel.org/r/20201113175917.189123-6-nikitos.tr@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
L8150 uses aw2013 LED contriller for notification LED on the front
of the device. Add it to the device tree
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Link: https://lore.kernel.org/r/20201113175917.189123-5-nikitos.tr@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
L8150 uses SGM3785 Flash LED driver. It is similar to SGM3140 but
can also be controlled with PWM. Since SoC doesn't have PWM, add
led to the device tree using sgm3140 driver.
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Link: https://lore.kernel.org/r/20201113175917.189123-4-nikitos.tr@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
L8150 has RMI4 compatible Synaptics touchscreen on
blsp_i2c5. It is powered by fixed regulator. Add
both to the device tree.
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Link: https://lore.kernel.org/r/20201113175917.189123-2-nikitos.tr@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
L8150 has a vibrator connected to PM8916. Add it to the device tree.
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Link: https://lore.kernel.org/r/20201113175917.189123-1-nikitos.tr@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch wires up touchscreen support on Samsung Galaxy A3 2015.
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Michael Srba <Michael.Srba@seznam.cz>
Link: https://lore.kernel.org/r/20201115195058.27097-1-michael.srba@seznam.cz
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
There's a proximity sensor on Lazor devices, but only for LTE SKUs.
Enable it only on the Lazor LTE SKUs and also configure it properly so
it works.
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20201120183825.547310-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This interrupt has an external pull-up so we don't need to pull it up
again. Drop the internal pull here. Note I don't think this really
changes anything, just noticed while looking at this irq pin.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20201120200913.618274-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
RB5 makes use of the two USB controllers onboard. USB0 is connected
to the Type C port and USB1 is connected to USB3.1 HUB which exposes
following downstream ports:
* 2 Type A ports
* 2 HS/SS ports on the expansion connector
* USB to LAN device
Hence, enable these two controllers with the required PHYs.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200917082622.6823-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
RNG (Random Number Generator) in SM8250 features PRNG EE (Execution
Environment), hence add devicetree support for it.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200921065806.10928-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Qualcomm boards should define two compatible strings: one for board,
anoter one for SoC family. sm8250-mtp.dts lists just the board
compatible, which makes it incompatible with qcom.yaml schema.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 60378f1a17 ("arm64: dts: qcom: sm8250: Add sm8250 dts file")
Link: https://lore.kernel.org/r/20200930112133.2091505-1-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add support for uSD card on RB5 using the SDHC2 interface.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[DB: disabled 1.8V support to get SDHC to work]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201028190955.1264526-2-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add support for SDC2 which can be used to interface uSD card.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[DB: minor fixes: clocks, iommus, opps]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201028190955.1264526-1-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add initial HDK865 dts, based on sm8250-mtp, with a few changes.
Notably, regulator configs are changed a bit.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200609194030.17756-9-jonathan@marek.ca
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
To enable seccomp constant action bitmaps, we need to have a static
mapping to the audit architecture and system call table size. Add these
for arm64.
Signed-off-by: Kees Cook <keescook@chromium.org>
We recently introduced a 1 GB sized ZONE_DMA to cater for platforms
incorporating masters that can address less than 32 bits of DMA, in
particular the Raspberry Pi 4, which has 4 or 8 GB of DRAM, but has
peripherals that can only address up to 1 GB (and its PCIe host
bridge can only access the bottom 3 GB)
Instructing the DMA layer about these limitations is straight-forward,
even though we had to fix some issues regarding memory limits set in
the IORT for named components, and regarding the handling of ACPI _DMA
methods. However, the DMA layer also needs to be able to allocate
memory that is guaranteed to meet those DMA constraints, for bounce
buffering as well as allocating the backing for consistent mappings.
This is why the 1 GB ZONE_DMA was introduced recently. Unfortunately,
it turns out the having a 1 GB ZONE_DMA as well as a ZONE_DMA32 causes
problems with kdump, and potentially in other places where allocations
cannot cross zone boundaries. Therefore, we should avoid having two
separate DMA zones when possible.
So let's do an early scan of the IORT, and only create the ZONE_DMA
if we encounter any devices that need it. This puts the burden on
the firmware to describe such limitations in the IORT, which may be
redundant (and less precise) if _DMA methods are also being provided.
However, it should be noted that this situation is highly unusual for
arm64 ACPI machines. Also, the DMA subsystem still gives precedence to
the _DMA method if implemented, and so we will not lose the ability to
perform streaming DMA outside the ZONE_DMA if the _DMA method permits
it.
[nsaenz: unified implementation with DT's counterpart]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Cc: Jeremy Linton <jeremy.linton@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20201119175400.9995-7-nsaenzjulienne@suse.de
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We recently introduced a 1 GB sized ZONE_DMA to cater for platforms
incorporating masters that can address less than 32 bits of DMA, in
particular the Raspberry Pi 4, which has 4 or 8 GB of DRAM, but has
peripherals that can only address up to 1 GB (and its PCIe host
bridge can only access the bottom 3 GB)
The DMA layer also needs to be able to allocate memory that is
guaranteed to meet those DMA constraints, for bounce buffering as well
as allocating the backing for consistent mappings. This is why the 1 GB
ZONE_DMA was introduced recently. Unfortunately, it turns out the having
a 1 GB ZONE_DMA as well as a ZONE_DMA32 causes problems with kdump, and
potentially in other places where allocations cannot cross zone
boundaries. Therefore, we should avoid having two separate DMA zones
when possible.
So, with the help of of_dma_get_max_cpu_address() get the topmost
physical address accessible to all DMA masters in system and use that
information to fine-tune ZONE_DMA's size. In the absence of addressing
limited masters ZONE_DMA will span the whole 32-bit address space,
otherwise, in the case of the Raspberry Pi 4 it'll only span the 30-bit
address space, and have ZONE_DMA32 cover the rest of the 32-bit address
space.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20201119175400.9995-6-nsaenzjulienne@suse.de
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
zone_dma_bits's initialization happens earlier that it's actually
needed, in arm64_memblock_init(). So move it into the more suitable
zone_sizes_init().
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Link: https://lore.kernel.org/r/20201119175400.9995-3-nsaenzjulienne@suse.de
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
crashkernel might reserve memory located in ZONE_DMA. We plan to delay
ZONE_DMA's initialization after unflattening the devicetree and ACPI's
boot table initialization, so move it later in the boot process.
Specifically into bootmem_init() since request_standard_resources()
depends on it.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Link: https://lore.kernel.org/r/20201119175400.9995-2-nsaenzjulienne@suse.de
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
mem_init() currently relies on knowing the boundaries of the crashkernel
reservation to map such region with page granularity for later
unmapping via set_memory_valid(..., 0). If the crashkernel reservation
is deferred, such boundaries are not known when the linear mapping is
created. Simply parse the command line for "crashkernel" and, if found,
create the linear map with NO_BLOCK_MAPPINGS.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: James Morse <james.morse@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20201119175556.18681-1-catalin.marinas@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add the apps_smmu node for sm8250.
For UFS, now that the kernel initializes the iommu, the stream mappings
set by the bootloader are cleared. Adding the iommus property is required
so that new mappings are created for UFS.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200609194030.17756-5-jonathan@marek.ca
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the apps_smmu node for sm8150.
For UFS, now that the kernel initializes the iommu, the stream mappings
set by the bootloader are cleared. Adding the iommus property is required
so that new mappings are created for UFS.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/20200609194030.17756-4-jonathan@marek.ca
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Currently <crypto/sha.h> contains declarations for both SHA-1 and SHA-2,
and <crypto/sha3.h> contains declarations for SHA-3.
This organization is inconsistent, but more importantly SHA-1 is no
longer considered to be cryptographically secure. So to the extent
possible, SHA-1 shouldn't be grouped together with any of the other SHA
versions, and usage of it should be phased out.
Therefore, split <crypto/sha.h> into two headers <crypto/sha1.h> and
<crypto/sha2.h>, and make everyone explicitly specify whether they want
the declarations for SHA-1, SHA-2, or both.
This avoids making the SHA-1 declarations visible to files that don't
want anything to do with SHA-1. It also prepares for potentially moving
sha1.h into a new insecure/ or dangerous/ directory.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Instead of copying the calculated authentication tag to memory and
calling crypto_memneq() to verify it, use vector bytewise compare and
min across vector instructions to decide whether the tag is valid. This
is more efficient, and given that the tag is only transiently held in a
NEON register, it is also safer, given that calculated tags for failed
decryptions should be withheld.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently, the kernel assumes that if RAM starts above 32-bit (or
zone_bits), there is still a ZONE_DMA/DMA32 at the bottom of the RAM and
such constrained devices have a hardwired DMA offset. In practice, we
haven't noticed any such hardware so let's assume that we can expand
ZONE_DMA32 to the available memory if no RAM below 4GB. Similarly,
ZONE_DMA is expanded to the 4GB limit if no RAM addressable by
zone_bits.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20201118185809.1078362-1-catalin.marinas@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The Qualcomm SCM driver was never explicitly enabled in the defconfig.
Instead it was (apparently) selected by DRM_MSM and by the recent change
to make it tristate now became =m.
Unfortunately this removes the ability for PINCTRL_MSM and ARM_SMMU to
be =y and with deferred_probe_timeout defaulting to 0 this means that
things such as UART, USB, PCIe and SDHCI probes with their dependencies
ignored.
The lack of pinctrl results in invalid pin configuration and the lack of
iommu results in the system locking up as soon as any form of data
transfer is attempted from any of the affected peripherals.
Mark QCOM_SCM as builtin, to avoid this.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201118162528.454729-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Task scheduler behavior depends on frequency invariance (FI) support and
the resulting invariant load tracking signals. For example, in order to
make accurate predictions across CPUs for all performance states, Energy
Aware Scheduling (EAS) needs frequency-invariant load tracking signals
and therefore it has a direct dependency on FI. This dependency is known,
but EAS enablement is not yet conditioned on the presence of FI during
the built of the scheduling domain hierarchy.
Before this is done, the following must be considered: while
arch_scale_freq_invariant() will see changes in FI support and could
be used to condition the use of EAS, it could return different values
during system initialisation.
For arm64, such a scenario will happen for a system that does not support
cpufreq driven FI, but does support counter-driven FI. For such a system,
arch_scale_freq_invariant() will return false if called before counter
based FI initialisation, but change its status to true after it.
If EAS becomes explicitly dependent on FI this would affect the task
scheduler behavior which builds its scheduling domain hierarchy well
before the late counter-based FI init. During that process, EAS would be
disabled due to its dependency on FI.
Two points of future early calls to arch_scale_freq_invariant() which
would determine EAS enablement are:
- (1) drivers/base/arch_topology.c:126 <<update_topology_flags_workfn>>
rebuild_sched_domains();
This will happen after CPU capacity initialisation.
- (2) kernel/sched/cpufreq_schedutil.c:917 <<rebuild_sd_workfn>>
rebuild_sched_domains_energy();
-->rebuild_sched_domains();
This will happen during sched_cpufreq_governor_change() for the
schedutil cpufreq governor.
Therefore, before enforcing the presence of FI support for the use of EAS,
ensure the following: if there is a change in FI support status after
counter init, use the existing rebuild_sched_domains_energy() function to
trigger a rebuild of the scheduling and performance domains that in turn
will determine the enablement of EAS.
Signed-off-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lkml.kernel.org/r/20201027180713.7642-3-ionela.voinescu@arm.com
We don't need to check for MTE support before checking the flag
because it can only be set if the hardware supports MTE. As a result
we can unconditionally check the flag bit which is expected to be in
a register and therefore the check can be done in a single instruction
instead of first needing to load the hwcaps.
On a DragonBoard 845c with a kernel built with CONFIG_ARM64_MTE=y with
the powersave governor this reduces the cost of a kernel entry/exit
(invalid syscall) from 465.1ns to 463.8ns.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Link: https://linux-review.googlesource.com/id/If4dc3501fd4e4f287322f17805509613cfe47d24
Link: https://lore.kernel.org/r/20201118032051.1405907-1-pcc@google.com
[catalin.marinas@arm.com: remove IS_ENABLED(CONFIG_ARM64_MTE)]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This property is for consumers of io-channels. Here it is used in
providers of those channels.
Note dt-schema will currently flag this as an error due to a dependency
between this property and io-channels.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20201115192951.1073632-9-jic23@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
It was recently reported that if GICR_TYPER is accessed before the RD base
address is set, we'll suffer from the unset @rdreg dereferencing. Oops...
gpa_t last_rdist_typer = rdreg->base + GICR_TYPER +
(rdreg->free_index - 1) * KVM_VGIC_V3_REDIST_SIZE;
It's "expected" that users will access registers in the redistributor if
the RD has been properly configured (e.g., the RD base address is set). But
it hasn't yet been covered by the existing documentation.
Per discussion on the list [1], the reporting of the GICR_TYPER.Last bit
for userspace never actually worked. And it's difficult for us to emulate
it correctly given that userspace has the flexibility to access it any
time. Let's just drop the reporting of the Last bit for userspace for now
(userspace should have full knowledge about it anyway) and it at least
prevents kernel from panic ;-)
[1] https://lore.kernel.org/kvmarm/c20865a267e44d1e2c0d52ce4e012263@kernel.org/
Fixes: ba7b3f1275 ("KVM: arm/arm64: Revisit Redistributor TYPER last bit computation")
Reported-by: Keqian Zhu <zhukeqian1@huawei.com>
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20201117151629.1738-1-yuzenghui@huawei.com
Cc: stable@vger.kernel.org
When section mappings are enabled, we allocate vmemmap pages from
physically continuous memory of size PMD_SIZE using
vmemmap_alloc_block_buf(). Section mappings are good to reduce TLB
pressure. But when system is highly fragmented and memory blocks are
being hot-added at runtime, its possible that such physically continuous
memory allocations can fail. Rather than failing the memory hot-add
procedure, add a fallback option to allocate vmemmap pages from
discontinuous pages using vmemmap_populate_basepages().
Signed-off-by: Sudarshan Rajagopalan <sudaraja@codeaurora.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Logan Gunthorpe <logang@deltatee.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/d6c06f2ef39bbe6c715b2f6db76eb16155fdcee6.1602722808.git.sudaraja@codeaurora.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Even though support for EFI boot remains entirely optional for arm64,
it is unlikely that we will ever be able to repurpose the image header
fields that the EFI loader relies on, i.e., the magic NOP at offset
0x0 and the PE header address at offset 0x3c.
So let's factor out the differences into a 'efi_signature_nop' macro and
a local symbol representing the PE header address, and move the
conditional definitions into efi-header.S, taking into account whether
CONFIG_EFI is enabled or not. While at it, switch to a signature NOP
that behaves more like a NOP, i.e., one that only clobbers the
flags.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201117124729.12642-4-ardb@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We no longer map the first 64 KB of the kernel image, as there is nothing
there that we ever need to refer back to once the kernel has booted. Even
though facilities like kallsyms are very careful to only refer to the
region that starts at _stext when mapping virtual addresses to symbol
names, let's avoid any confusion by switching to local .L prefixed symbol
names for the EFI header, as none of them have any significance to the
rest of the kernel.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201117124729.12642-3-ardb@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In a previous patch, we increased the size of the EFI PE/COFF header
to 64 KB, which resulted in the _stext symbol to appear at a fixed
offset of 64 KB into the image.
Since 64 KB is also the largest page size we support, this completely
removes the need to map the first 64 KB of the kernel image, given that
it only contains the arm64 Image header and the EFI header, neither of
which we ever access again after booting the kernel. More importantly,
we should avoid an executable mapping of non-executable and not entirely
predictable data, to deal with the unlikely event that we inadvertently
emitted something that looks like an opcode that could be used as a
gadget for speculative execution.
So let's limit the kernel mapping of .text to the [_stext, _etext)
region, which matches the view of generic code (such as kallsyms) when
it reasons about the boundaries of the kernel's .text section.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201117124729.12642-2-ardb@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add arm64 IMA arch support. The code and arch policy is mainly inherited
from x86.
Co-developed-by: Chester Lin <clin@suse.com>
Signed-off-by: Chester Lin <clin@suse.com>
Acked-by: Mimi Zohar <zohar@linux.ibm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The scripts/dtc/checks.c requires that the node have empty "dma-ranges"
property must have the same "#address-cells" and "#size-cells" values as
the parent node. Otherwise, the following warnings is reported:
arch/arm64/boot/dts/qcom/ipq6018.dtsi:185.3-14: Warning \
(dma_ranges_format): /soc:dma-ranges: empty "dma-ranges" property but \
its #address-cells (1) differs from / (2)
arch/arm64/boot/dts/qcom/ipq6018.dtsi:185.3-14: Warning \
(dma_ranges_format): /soc:dma-ranges: empty "dma-ranges" property but \
its #size-cells (1) differs from / (2)
Arnd Bergmann figured out why it's necessary:
Also note that the #address-cells=<1> means that any device under
this bus is assumed to only support 32-bit addressing, and DMA will
have to go through a slow swiotlb in the absence of an IOMMU.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201016090833.1892-3-thunder.leizhen@huawei.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The scripts/dtc/checks.c requires that the node have empty "dma-ranges"
property must have the same "#address-cells" and "#size-cells" values as
the parent node. Otherwise, the following warnings is reported:
arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \
(dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \
its #address-cells (1) differs from / (2)
arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \
(dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \
its #size-cells (1) differs from / (2)
Arnd Bergmann figured out why it's necessary:
Also note that the #address-cells=<1> means that any device under
this bus is assumed to only support 32-bit addressing, and DMA will
have to go through a slow swiotlb in the absence of an IOMMU.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20201016090833.1892-2-thunder.leizhen@huawei.com'
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the sub-mailbox nodes that are used to communicate between MPU and
various remote processors present in the J7200 SoCs to the J7200 common
processor board. These include the R5F remote processors in the dual-R5F
clusters in the MCU domain (MCU_R5FSS0) and the MAIN domain (MAIN_R5FSS0).
These sub-mailbox nodes utilize the System Mailbox clusters 0 and 1. All
the remaining mailbox clusters are currently not used on A72 core, and
so are disabled. The nodes are added in the k3-j7200-som-p0.dtsi file
to co-locate these alongside future reserved-memory nodes required for
remoteprocs.
The sub-mailbox nodes added match the hard-coded mailbox configuration
used within the TI RTOS IPC software packages. A sub-mailbox node is added
for each of the R5F cores to accommodate the R5F processor sub-systems
running in Split mode. Only the sub-mailbox node for the first R5F core in
each cluster is used in case of Lockstep mode for that R5F cluster.
NOTE:
The GIC_SPI interrupts to be used are dynamically allocated and managed
by the System Firmware through the ti-sci-intr irqchip driver. So, only
valid interrupts that are used by the sub-mailbox devices (each cluster's
User 0 IRQ output) are enabled. This is done to minimize the number of
NavSS Interrupt Router outputs utilized.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Praneeth Bajjuri <praneeth@ti.com>
Link: https://lore.kernel.org/r/20201026232637.15681-4-s-anna@ti.com
The J7200 Main NavSS block contains a Mailbox IP instance with
multiple clusters, and follows the same integration style as on
J721E SoCs.
Add all the Mailbox clusters as their own nodes under the MAIN
NavSS interconnect node instead of creating an almost empty parent
node for the new K3 mailbox IP and the clusters as its child nodes.
All these nodes are enabled by default in the base dtsi file, but
any cluster that does not define any child sub-mailbox nodes
should be disabled in the corresponding board dts files.
NOTE:
The NavSS only has a limited number of interrupts, so none of the
interrupts generated by a Mailbox IP are added by default. Only
the needed interrupts that are targeted towards the A72 GIC will
have to be added later on in the board dts files alongside the
corresponding sub-mailbox child nodes.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Praneeth Bajjuri <praneeth@ti.com>
Link: https://lore.kernel.org/r/20201026232637.15681-3-s-anna@ti.com
The Main NavSS block on J7200 SoCs contains a HwSpinlock IP instance that
is same as the IP on AM65x and J721E SoCs. Add the DT node for this on
J7200 SoCs. The node is present within the Main NavSS block, and is added
as a child node under the main_navss interconnect node.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Praneeth Bajjuri <praneeth@ti.com>
Link: https://lore.kernel.org/r/20201026232637.15681-2-s-anna@ti.com
Follow the device tree standards that states to set the
status="reserved" if an device is operational, but used by a non-linux
firmware in the system.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201113211826.13087-6-nm@ti.com
The default state of a device tree node is "okay". There is no specific
use of explicitly adding status = "okay" in the board dts.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20201113211826.13087-5-nm@ti.com
The default state of a device tree node is "okay". There is no specific
use of explicitly adding status = "okay" in the SoC dtsi.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Link: https://lore.kernel.org/r/20201113211826.13087-4-nm@ti.com
The device tree standard states that when the status property is
not present under a node, the okay value is assumed. There are many
reasons for doing the same, the number of strings in the device
tree, default power management functionality, etc. are a few of the
reasons.
In general, after a few rounds of discussions [1] there are few
options one could take when dealing with SoC dtsi and board dts
a. SoC dtsi provide nodes as a super-set default (aka enabled) state and
to prevent messy board files, when more boards are added per SoC, we
optimize and disable commonly un-used nodes in board-common.dtsi
b. SoC dtsi disables all hardware dependent nodes by default and board
dts files enable nodes based on a need basis.
c. Subjectively pick and choose which nodes we will disable by default
in SoC dtsi and over the years we can optimize things and change
default state depending on the need.
While there are pros and cons on each of these approaches, the right
thing to do will be to stick with device tree default standards and
work within those established rules. So, we choose to go with option
(a).
Lets cleanup defaults of j721e SoC dtsi before this gets more harder
to cleanup later on and new SoCs are added.
The only functional difference between the dtb generated is
status='okay' is no longer necessary for mcasp10 and depends on the
default state.
NOTE: There is a known risk of omission that new board dts developers
might miss reviewing both the board schematics in addition to all the
DT nodes of the SoC when setting appropriate nodes status to disable
or reserved in the board dts. This can expose issues in drivers that
may not anticipate an incomplete node (example: missing appropriate
board properties) being in an "okay" state. These cases are considered
bugs and need to be fixed in the drivers as and when identified.
[1] https://lore.kernel.org/linux-arm-kernel/20201027130701.GE5639@atomide.com/
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20201113211826.13087-3-nm@ti.com
The device tree standard states that when the status property is
not present under a node, the okay value is assumed. There are many
reasons for doing the same, the number of strings in the device
tree, default power management functionality, etc. are a few of the
reasons.
In general, after a few rounds of discussions [1] there are few
options one could take when dealing with SoC dtsi and board dts
a. SoC dtsi provide nodes as a super-set default (aka enabled) state and
to prevent messy board files, when more boards are added per SoC, we
optimize and disable commonly un-used nodes in board-common.dtsi
b. SoC dtsi disables all hardware dependent nodes by default and board
dts files enable nodes based on a need basis.
c. Subjectively pick and choose which nodes we will disable by default
in SoC dtsi and over the years we can optimize things and change
default state depending on the need.
While there are pros and cons on each of these approaches, the right
thing to do will be to stick with device tree default standards and
work within those established rules. So, we choose to go with option
(a).
Lets cleanup defaults of am654 SoC dtsi before this gets more harder
to cleanup later on and new SoCs are added.
The dtb generated is identical with the patch and it is just cleanup to
ensure we have a clean usage model
NOTE: There is a known risk of omission that new board dts developers
might miss reviewing both the board schematics in addition to all the
DT nodes of the SoC when setting appropriate nodes status to disable
or reserved in the board dts. This can expose issues in drivers that
may not anticipate an incomplete node (example: missing appropriate
board properties) being in an "okay" state. These cases are considered
bugs and need to be fixed in the drivers as and when identified.
[1] https://lore.kernel.org/linux-arm-kernel/20201027130701.GE5639@atomide.com/
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20201113211826.13087-2-nm@ti.com
Around one third of the fixes this time are for dts files that list
their ethernet controller as using 'phy-mode="rgmii"' but are changed to
'phy-mode="rgmii-id"' now, because the PHY drivers (realtek, ksz9031,
dp83867, ...) now configure the internal delay based on that when they
used to stay on the hardware default.
The long story is archived at
https://lore.kernel.org/netdev/CAMj1kXEEF_Un-4NTaD5iUN0NoZYaJQn-rPediX0S6oRiuVuW-A@mail.gmail.com/
I was trying to hold off on the bugfixes until there was a solution that
would avoid breaking all boards, but that does not seem to be happening
any time soon, so I am now sending the correct version of the dts files to
ensure that at least these machines can use their network devices again.
The other changes this time are:
- Updating the MAINTAINER lists for Allwinner and Samsung SoCs
- Multiple i.MX8MN machines get updates for their CPU
operating points to match the data sheet
- A revert for a dts patch that caused a regression in USB
support on Odroid U3
- Two fixes for the AMD Tee driver, addressing a memory leak
and missing locking
- Mark the network subsystem on qoriq-fman3 as cache coherent
for correctness as better performance.
- Minor dts fixes elsewhere, addressing dtc warnings and similar
problems
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=Qgm/
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-fixes-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Around one third of the fixes this time are for dts files that list
their ethernet controller as using 'phy-mode="rgmii"' but are changed
to 'phy-mode="rgmii-id"' now, because the PHY drivers (realtek,
ksz9031, dp83867, ...) now configure the internal delay based on that
when they used to stay on the hardware default.
The long story is archived at
https://lore.kernel.org/netdev/CAMj1kXEEF_Un-4NTaD5iUN0NoZYaJQn-rPediX0S6oRiuVuW-A@mail.gmail.com/
I was trying to hold off on the bugfixes until there was a solution
that would avoid breaking all boards, but that does not seem to be
happening any time soon, so I am now sending the correct version of
the dts files to ensure that at least these machines can use their
network devices again.
The other changes this time are:
- Updating the MAINTAINER lists for Allwinner and Samsung SoCs
- Multiple i.MX8MN machines get updates for their CPU operating
points to match the data sheet
- A revert for a dts patch that caused a regression in USB support on
Odroid U3
- Two fixes for the AMD Tee driver, addressing a memory leak and
missing locking
- Mark the network subsystem on qoriq-fman3 as cache coherent for
correctness as better performance.
- Minor dts fixes elsewhere, addressing dtc warnings and similar
problems"
* tag 'arm-soc-fixes-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: dts: exynos: revert "add input clock to CMU in Exynos4412 Odroid"
ARM: dts: imx50-evk: Fix the chip select 1 IOMUX
arm64: dts: imx8mm: fix voltage for 1.6GHz CPU operating point
ARM: dts: stm32: Keep VDDA LDO1 always on on DHCOM
ARM: dts: stm32: Enable thermal sensor support on stm32mp15xx-dhcor
ARM: dts: stm32: Define VIO regulator supply on DHCOM
ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2
ARM: dts: stm32: Fix TA3-GPIO-C key on STM32MP1 DHCOM PDK2
arm64: dts: renesas: r8a774e1: Add missing audio_clk_b
tee: amdtee: synchronize access to shm list
tee: amdtee: fix memory leak due to reset of global shm list
arm64: dts: agilex/stratix10: Fix qspi node compatible
ARM: dts: imx6q-prti6q: fix PHY address
ARM: dts: vf610-zii-dev-rev-b: Fix MDIO over clocking
arm: dts: imx6qdl-udoo: fix rgmii phy-mode for ksz9031 phy
arm64: dts imx8mn: Remove non-existent USB OTG2
arm64: dts: imx8mm-beacon-som: Fix Choppy BT audio
arm64: dts: fsl: DPAA FMan DMA operations are coherent
arm64: dts: fsl: fix endianness issue of rcpm
arm64: dts: imx8mn-evk: fix missing PMIC's interrupt line pull-up
...
- Fix MDIO over clocking on vf610-zii-dev-rev-b board to get switch
device work reliably.
- Fix imx50-evk IOMUX for the chip select 1 to use GPIO4_13 instead of
the native CSPI_SSI function.
- Fix voltage for 1.6GHz CPU operating point on i.MX8MM to match
hardware datasheet.
- Fix phy-mode for KSZ9031 PHY on imx6qdl-udoo board.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl+yQKUUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM7dVgf1GkIY1GbPIvkMZB3CiQZ0e40vUmWx
CW70bOrGAcSSgYvL7tBqb7I5U5+01m4whtsal6jK/TTZ4w2PAItZpgi3ZiXooyO9
3qGHr7IgcuCWzQ2Bjg+YGR1esGTi2+KKggCWog0R8ipy5gUCvIcuLNyBtxjlkbKt
1kkxEDOdmeXPAUQboEdRPZF4m6J/q8g/QgY8GeLsPeContEvAXBMMdNgIRHmWZ6H
iu3H33ogseBkm5RvSfdjmTKPnz9/5hF94yEpGgTkWrawq2bMXwt7loBsQl/TyUVg
d01gZl5yOxjtMXcnJ5bW+6SOpPbjUBFczg1+C2u2tDpeES5DjjYLS0fb
=zT+s
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.10, round 4:
- Fix MDIO over clocking on vf610-zii-dev-rev-b board to get switch
device work reliably.
- Fix imx50-evk IOMUX for the chip select 1 to use GPIO4_13 instead of
the native CSPI_SSI function.
- Fix voltage for 1.6GHz CPU operating point on i.MX8MM to match
hardware datasheet.
- Fix phy-mode for KSZ9031 PHY on imx6qdl-udoo board.
* tag 'imx-fixes-5.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx50-evk: Fix the chip select 1 IOMUX
arm64: dts: imx8mm: fix voltage for 1.6GHz CPU operating point
ARM: dts: vf610-zii-dev-rev-b: Fix MDIO over clocking
arm: dts: imx6qdl-udoo: fix rgmii phy-mode for ksz9031 phy
Link: https://lore.kernel.org/r/20201116090702.GM5849@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The hyp vectors entry corresponding to HYP_VECTOR_DIRECT (i.e. when
neither Spectre-v2 nor Spectre-v3a are present) is unused, as we can
simply dispatch straight to __kvm_hyp_vector in this case.
Remove the redundant vector, and massage the logic for resolving a slot
to a vectors entry.
Reported-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201113113847.21619-11-will@kernel.org
The spectre-v3a mitigation is split between cpu_errata.c and spectre.c,
with the former handling detection of the problem and the latter handling
enabling of the workaround.
Move the detection logic alongside the enabling logic, like we do for the
other spectre mitigations.
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Quentin Perret <qperret@google.com>
Link: https://lore.kernel.org/r/20201113113847.21619-10-will@kernel.org
Since ARM64_HARDEN_EL2_VECTORS is really a mitigation for Spectre-v3a,
rename it accordingly for consistency with the v2 and v4 mitigation.
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Quentin Perret <qperret@google.com>
Link: https://lore.kernel.org/r/20201113113847.21619-9-will@kernel.org
The EL2 vectors installed when a guest is running point at one of the
following configurations for a given CPU:
- Straight at __kvm_hyp_vector
- A trampoline containing an SMC sequence to mitigate Spectre-v2 and
then a direct branch to __kvm_hyp_vector
- A dynamically-allocated trampoline which has an indirect branch to
__kvm_hyp_vector
- A dynamically-allocated trampoline containing an SMC sequence to
mitigate Spectre-v2 and then an indirect branch to __kvm_hyp_vector
The indirect branches mean that VA randomization at EL2 isn't trivially
bypassable using Spectre-v3a (where the vector base is readable by the
guest).
Rather than populate these vectors dynamically, configure everything
statically and use an enumerated type to identify the vector "slot"
corresponding to one of the configurations above. This both simplifies
the code, but also makes it much easier to implement at EL2 later on.
Signed-off-by: Will Deacon <will@kernel.org>
[maz: fixed double call to kvm_init_vector_slots() on nVHE]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Quentin Perret <qperret@google.com>
Link: https://lore.kernel.org/r/20201113113847.21619-8-will@kernel.org
The hardened hyp vectors are not used on systems running with VHE or CPUs
without the ARM64_HARDEN_EL2_VECTORS capability.
Re-jig the checking logic slightly in kvm_patch_vector_branch() so that
it's a bit clearer what we're looking for. This is purely cosmetic.
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Quentin Perret <qperret@google.com>
Link: https://lore.kernel.org/r/20201113113847.21619-7-will@kernel.org
The BP hardening helpers are an integral part of the Spectre-v2
mitigation, so move them into asm/spectre.h and inline the
arm64_get_bp_hardening_data() function at the same time.
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Quentin Perret <qperret@google.com>
Link: https://lore.kernel.org/r/20201113113847.21619-6-will@kernel.org
Branch predictor hardening of the hyp vectors is partially driven by a
couple of global variables ('__kvm_bp_vect_base' and
'__kvm_harden_el2_vector_slot'). However, these are only used within a
single compilation unit, so internalise them there instead.
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Quentin Perret <qperret@google.com>
Link: https://lore.kernel.org/r/20201113113847.21619-5-will@kernel.org
kvm_get_hyp_vector() has only one caller, so move it out of kvm_mmu.h
and inline it into a new function, cpu_set_hyp_vector(), for setting
the vector.
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Quentin Perret <qperret@google.com>
Link: https://lore.kernel.org/r/20201113113847.21619-4-will@kernel.org
The bulk of the work in kvm_map_vector() is conditional on the
ARM64_HARDEN_EL2_VECTORS capability, so return early if that is not set
and make the code a bit easier to read.
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Quentin Perret <qperret@google.com>
Link: https://lore.kernel.org/r/20201113113847.21619-3-will@kernel.org
'__kvm_bp_vect_base' is only used when dealing with the hardened vectors
so remove the redundant assignments in kvm_map_vectors().
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Quentin Perret <qperret@google.com>
Link: https://lore.kernel.org/r/20201113113847.21619-2-will@kernel.org
The nVHE percpu data is partially linked but the nVHE linker script did
not align the percpu section. The PERCPU_INPUT macro would then align
the data to a page boundary:
#define PERCPU_INPUT(cacheline) \
__per_cpu_start = .; \
*(.data..percpu..first) \
. = ALIGN(PAGE_SIZE); \
*(.data..percpu..page_aligned) \
. = ALIGN(cacheline); \
*(.data..percpu..read_mostly) \
. = ALIGN(cacheline); \
*(.data..percpu) \
*(.data..percpu..shared_aligned) \
PERCPU_DECRYPTED_SECTION \
__per_cpu_end = .;
but then when the final vmlinux linking happens the hypervisor percpu
data is included after page alignment and so the offsets potentially
don't match. On my build I saw that the .hyp.data..percpu section was
at address 0x20 and then the percpu data would begin at 0x1000 (because
of the page alignment in PERCPU_INPUT), but when linked into vmlinux,
everything would be shifted down by 0x20 bytes.
This manifests as one of the CPUs getting lost when running
kvm-unit-tests or starting any VM and subsequent soft lockup on a Cortex
A72 device.
Fixes: 30c953911c ("kvm: arm64: Set up hyp percpu data for nVHE")
Signed-off-by: Jamie Iles <jamie@nuviainc.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: David Brazdil <dbrazdil@google.com>
Cc: David Brazdil <dbrazdil@google.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201113150406.14314-1-jamie@nuviainc.com
without two-dimensional paging (EPT/NPT).
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl+xQ54UHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMzeQf+JP9NpXgeB7dhiODhmO5SyLdw0u9j
kVOM6+kHcEvG6o0yU1uUZr2ZPh9vIAwIjXi8Luiodcazdp6jvxvJ32CeMYJz2lel
y+3Gjp3WS2+FExOjBephBztaMHLihlWQt3E0EKuCc7StyfMhaZooiTRMpvrmiLWe
HQ/epM9oLMyrCqG9MKkvTwH0lDyB5CprV1BNt6YyKjt7d5swEqC75A6lOXnmdAah
utgx1agSIVQPv6vDF9HLaQaoelHT7ucudx+zIkvOAmoQ56AJMPfCr0+Af3ZVW+f/
I5tXVfBhoOV3BVSIsJS7Px0HcZt7siVtl6ISZZos8ox85S4ysjWm2vXFcQ==
=MiOr
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Fixes for ARM and x86, the latter especially for old processors
without two-dimensional paging (EPT/NPT)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: mmu: fix is_tdp_mmu_check when the TDP MMU is not in use
KVM: SVM: Update cr3_lm_rsvd_bits for AMD SEV guests
KVM: x86: Introduce cr3_lm_rsvd_bits in kvm_vcpu_arch
KVM: x86: clflushopt should be treated as a no-op by emulation
KVM: arm64: Handle SCXTNUM_ELx traps
KVM: arm64: Unify trap handlers injecting an UNDEF
KVM: arm64: Allow setting of ID_AA64PFR0_EL1.CSV2 from userspace
- A set of commits which reduce the stack usage of various perf event
handling functions which allocated large data structs on stack causing
stack overflows in the worst case.
- Use the proper mechanism for detecting soft interrupts in the recursion
protection.
- Make the resursion protection simpler and more robust.
- Simplify the scheduling of event groups to make the code more robust and
prepare for fixing the issues vs. scheduling of exclusive event groups.
- Prevent event multiplexing and rotation for exclusive event groups
- Correct the perf event attribute exclusive semantics to take pinned
events, e.g. the PMU watchdog, into account
- Make the anythread filtering conditional for Intel's generic PMU
counters as it is not longer guaranteed to be supported on newer
CPUs. Check the corresponding CPUID leaf to make sure.
- Fixup a duplicate initialization in an array which was probably cause by
the usual copy & paste - forgot to edit mishap.
-----BEGIN PGP SIGNATURE-----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=FzCf
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-2020-11-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"A set of fixes for perf:
- A set of commits which reduce the stack usage of various perf
event handling functions which allocated large data structs on
stack causing stack overflows in the worst case
- Use the proper mechanism for detecting soft interrupts in the
recursion protection
- Make the resursion protection simpler and more robust
- Simplify the scheduling of event groups to make the code more
robust and prepare for fixing the issues vs. scheduling of
exclusive event groups
- Prevent event multiplexing and rotation for exclusive event groups
- Correct the perf event attribute exclusive semantics to take
pinned events, e.g. the PMU watchdog, into account
- Make the anythread filtering conditional for Intel's generic PMU
counters as it is not longer guaranteed to be supported on newer
CPUs. Check the corresponding CPUID leaf to make sure
- Fixup a duplicate initialization in an array which was probably
caused by the usual 'copy & paste - forgot to edit' mishap"
* tag 'perf-urgent-2020-11-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Fix Add BW copypasta
perf/x86/intel: Make anythread filter support conditional
perf: Tweak perf_event_attr::exclusive semantics
perf: Fix event multiplexing for exclusive groups
perf: Simplify group_sched_in()
perf: Simplify group_sched_out()
perf/x86: Make dummy_iregs static
perf/arch: Remove perf_sample_data::regs_user_copy
perf: Optimize get_recursion_context()
perf: Fix get_recursion_context()
perf/x86: Reduce stack usage for x86_pmu::drain_pebs()
perf: Reduce stack usage of perf_output_begin()
Given that smp_call_function_single() can deadlock when interrupts are
disabled, abort the SMP call if irqs_disabled(). This scenario is
currently not possible given the function's uses, but safeguard this for
potential future uses.
Signed-off-by: Ionela Voinescu <ionela.voinescu@arm.com>
Cc: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20201113155328.4194-1-ionela.voinescu@arm.com
[catalin.marinas@arm.com: modified following Mark's comment]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
If Activity Monitors (AMUs) are present, two of the counters can be used
to implement support for CPPC's (Collaborative Processor Performance
Control) delivered and reference performance monitoring functionality
using FFH (Functional Fixed Hardware).
Given that counters for a certain CPU can only be read from that CPU,
while FFH operations can be called from any CPU for any of the CPUs, use
smp_call_function_single() to provide the requested values.
Therefore, depending on the register addresses, the following values
are returned:
- 0x0 (DeliveredPerformanceCounterRegister): AMU core counter
- 0x1 (ReferencePerformanceCounterRegister): AMU constant counter
The use of Activity Monitors is hidden behind the generic
cpu_read_{corecnt,constcnt}() functions.
Read functionality for these two registers represents the only current
FFH support for CPPC. Read operations for other register values or write
operation for all registers are unsupported. Therefore, keep CPPC's FFH
unsupported if no CPUs have valid AMU frequency counters. For this
purpose, the get_cpu_with_amu_feat() is introduced.
Signed-off-by: Ionela Voinescu <ionela.voinescu@arm.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201106125334.21570-4-ionela.voinescu@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In order for the counter validation function to be reused, split
validate_cpu_freq_invariance_counters() into:
- freq_counters_valid(cpu) - check cpu for valid cycle counters
- freq_inv_set_max_ratio(int cpu, u64 max_rate, u64 ref_rate) -
generic function that sets the normalization ratio used by
topology_scale_freq_tick()
Signed-off-by: Ionela Voinescu <ionela.voinescu@arm.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201106125334.21570-3-ionela.voinescu@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In preparation for other uses of Activity Monitors (AMU) cycle counters,
place counter read functionality in generic functions that can reused:
read_corecnt() and read_constcnt().
As a result, implement update_freq_counters_refs() to replace
init_cpu_freq_invariance_counters() and both initialise and update
the per-cpu reference variables.
Signed-off-by: Ionela Voinescu <ionela.voinescu@arm.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201106125334.21570-2-ionela.voinescu@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- Spectre/Meltdown safelisting for some Qualcomm KRYO cores
- Fix RCU splat when failing to online a CPU due to a feature mismatch
- Fix a recently introduced sparse warning in kexec()
- Fix handling of CPU erratum 1418040 for late CPUs
- Ensure hot-added memory falls within linear-mapped region
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl+ubogQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNPD7B/9i5ao44AEJwjz0a68S/jD7kUD7i3xVkCNN
Y8i/i9mx44IAcf8pmyQh3ngaFlJuF2C6oC/SQFiDbmVeGeZXLXvXV7uGAqXG5Xjm
O2Svgr1ry176JWpsB7MNnZwzAatQffdkDjbjQCcUnUIKYcLvge8H2fICljujGcfQ
094vNmT9VerTWRbWDti3Ck/ug+sanVHuzk5BWdKx3jamjeTqo+sBZK/wgBr6UoYQ
mT3BFX42kLIGg+AzwXRDPlzkJymjYgQDbSwGsvny8qKdOEJbAUwWXYZ5sTs9J/gU
E9PT3VJI7BYtTd1uPEWkD645U3arfx3Pf2JcJlbkEp86qx4CUF9s
=T6k4
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
- Spectre/Meltdown safelisting for some Qualcomm KRYO cores
- Fix RCU splat when failing to online a CPU due to a feature mismatch
- Fix a recently introduced sparse warning in kexec()
- Fix handling of CPU erratum 1418040 for late CPUs
- Ensure hot-added memory falls within linear-mapped region
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: cpu_errata: Apply Erratum 845719 to KRYO2XX Silver
arm64: proton-pack: Add KRYO2XX silver CPUs to spectre-v2 safe-list
arm64: kpti: Add KRYO2XX gold/silver CPU cores to kpti safelist
arm64: Add MIDR value for KRYO2XX gold/silver CPU cores
arm64/mm: Validate hotplug range before creating linear mapping
arm64: smp: Tell RCU about CPUs that fail to come online
arm64: psci: Avoid printing in cpu_psci_cpu_die()
arm64: kexec_file: Fix sparse warning
arm64: errata: Fix handling of 1418040 with late CPU onlining
The OSM L3 interconnect driver is used for scaling the bus to the L3
cache on modern Qualcomm platforms, enable it.
Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201113163444.3138807-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
J7200 has a single instance of 8 channel ADC in MCU domain. Add DT node
for the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Link: https://lore.kernel.org/r/20201029050950.4500-1-vigneshr@ti.com
- Fix the qspi node to have the required "jedec,spi-nor"
-----BEGIN PGP SIGNATURE-----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=Ro6d
-----END PGP SIGNATURE-----
Merge tag 'socfpga_fix_for_v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/fixes
arm64: dts: fix for v5.10
- Fix the qspi node to have the required "jedec,spi-nor"
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- A series from Krzysztof Kozlowski to fix missing PMIC's interrupt
line pull-up for i.MX8MM and i.MX8MN boards.
- Set Bluetooth chip max-speed to 4000000 on imx8mm-beacon-som board
to fix the choppy Bluetooth audio sound.
- Remove non-existent OTG2, usbphynop2, and the usbmisc2 from i.MX8MN
device tree.
- Fix the endianness setting of RCPM node on Layerscape SoCs.
- Add the missing dma-coherent property for qoriq-fman device to improve
the performance.
- Fix the Ethernet PHY address on imx6q-prti6q board.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl+fStkUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM6UJggAgRnnMfVrvpZqZSYlj3CirW4jOeeo
oxkh8L3XcvOh5f1StI15879a93E5fq4CLoVUda5vdWJLO8Q0pl5VGJsTfzNpekAY
mswq8ratwKragLOX8FhSr/YLICoF6qLmIDn0EtAuOwLrcii4i5pgLqj0t/5MQm9U
NyAbb/nYZWWm2S8szOaB6+OfYbXxV9YHMFkFL9ZetppS/ezYq3UNq2i//aTBB33z
wFhqt8+scuT3cikdtFumb+vbMMYtUcGfJxkgLEoQz3P53WL1w0jzJXQ47egWI6/d
16zEUavTk9WUKcWS8knY8KKToVaU6GKIr+JLUOczWOhMPUtxANsLvLOmjQ==
=M32F
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.10, 3rd round:
- A series from Krzysztof Kozlowski to fix missing PMIC's interrupt
line pull-up for i.MX8MM and i.MX8MN boards.
- Set Bluetooth chip max-speed to 4000000 on imx8mm-beacon-som board
to fix the choppy Bluetooth audio sound.
- Remove non-existent OTG2, usbphynop2, and the usbmisc2 from i.MX8MN
device tree.
- Fix the endianness setting of RCPM node on Layerscape SoCs.
- Add the missing dma-coherent property for qoriq-fman device to improve
the performance.
- Fix the Ethernet PHY address on imx6q-prti6q board.
* tag 'imx-fixes-5.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6q-prti6q: fix PHY address
arm64: dts imx8mn: Remove non-existent USB OTG2
arm64: dts: imx8mm-beacon-som: Fix Choppy BT audio
arm64: dts: fsl: DPAA FMan DMA operations are coherent
arm64: dts: fsl: fix endianness issue of rcpm
arm64: dts: imx8mn-evk: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mn-ddr4-evk: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mn-var-som: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mm-evk: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mm-beacon-som: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mm-var-som: fix missing PMIC's interrupt line pull-up
Link: https://lore.kernel.org/r/20201030151821.GA28266@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
QCOM KRYO2XX Silver cores are Cortex-A53 based and are
susceptible to the 845719 erratum. Add them to the lookup
list to apply the erratum.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20201104232218.198800-5-konrad.dybcio@somainline.org
Signed-off-by: Will Deacon <will@kernel.org>
QCOM KRYO2XX gold (big) silver (LITTLE) CPU cores are based on
Cortex-A73 and Cortex-A53 respectively and are meltdown safe,
hence add them to kpti_safe_list[].
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20201104232218.198800-3-konrad.dybcio@somainline.org
Signed-off-by: Will Deacon <will@kernel.org>
Add MIDR value for KRYO2XX gold (big) and silver (LITTLE)
CPU cores which are used in Qualcomm Technologies, Inc.
SoCs. This will be used to identify and apply errata
which are applicable for these CPU cores.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20201104232218.198800-2-konrad.dybcio@somainline.org
Signed-off-by: Will Deacon <will@kernel.org>
During memory hotplug process, the linear mapping should not be created for
a given memory range if that would fall outside the maximum allowed linear
range. Else it might cause memory corruption in the kernel virtual space.
Maximum linear mapping region is [PAGE_OFFSET..(PAGE_END -1)] accommodating
both its ends but excluding PAGE_END. Max physical range that can be mapped
inside this linear mapping range, must also be derived from its end points.
This ensures that arch_add_memory() validates memory hot add range for its
potential linear mapping requirements, before creating it with
__create_pgd_mapping().
Fixes: 4ab2150615 ("arm64: Add memory hotplug support")
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Steven Price <steven.price@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/1605252614-761-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Based on lessons learnt from optimizing the 32-bit version of this driver,
we can simplify the arm64 version considerably, by reordering the final
two stores when the last block is not a multiple of 64 bytes. This removes
the need to use permutation instructions to calculate the elements that are
clobbered by the final overlapping store, given that the store of the
penultimate block now follows it, and that one carries the correct values
for those elements already.
While at it, simplify the overlapping loads as well, by calculating the
address of the final overlapping load upfront, and switching to this
address for every load that would otherwise extend past the end of the
source buffer.
There is no impact on performance, but the resulting code is substantially
smaller and easier to follow.
Cc: Eric Biggers <ebiggers@google.com>
Cc: "Jason A . Donenfeld" <Jason@zx2c4.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Current release - regressions:
- arm64: dts: fsl-ls1028a-kontron-sl28: specify in-band mode for ENETC
Current release - bugs in new features:
- mptcp: provide rmem[0] limit offset to fix oops
Previous release - regressions:
- IPv6: Set SIT tunnel hard_header_len to zero to fix path MTU
calculations
- lan743x: correctly handle chips with internal PHY
- bpf: Don't rely on GCC __attribute__((optimize)) to disable GCSE
- mlx5e: Fix VXLAN port table synchronization after function reload
Previous release - always broken:
- bpf: Zero-fill re-used per-cpu map element
- net: udp: fix out-of-order packets when forwarding with UDP GSO
fraglists turned on
- fix UDP header access on Fast/frag0 UDP GRO
- fix IP header access and skb lookup on Fast/frag0 UDP GRO
- ethtool: netlink: add missing netdev_features_change() call
- net: Update window_clamp if SOCK_RCVBUF is set
- igc: Fix returning wrong statistics
- ch_ktls: fix multiple leaks and corner cases in Chelsio TLS offload
- tunnels: Fix off-by-one in lower MTU bounds for ICMP/ICMPv6 replies
- r8169: disable hw csum for short packets on all chip versions
- vrf: Fix fast path output packet handling with async Netfilter rules
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=AKM7
-----END PGP SIGNATURE-----
Merge tag 'net-5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Current release - regressions:
- arm64: dts: fsl-ls1028a-kontron-sl28: specify in-band mode for
ENETC
Current release - bugs in new features:
- mptcp: provide rmem[0] limit offset to fix oops
Previous release - regressions:
- IPv6: Set SIT tunnel hard_header_len to zero to fix path MTU
calculations
- lan743x: correctly handle chips with internal PHY
- bpf: Don't rely on GCC __attribute__((optimize)) to disable GCSE
- mlx5e: Fix VXLAN port table synchronization after function reload
Previous release - always broken:
- bpf: Zero-fill re-used per-cpu map element
- fix out-of-order UDP packets when forwarding with UDP GSO fraglists
turned on:
- fix UDP header access on Fast/frag0 UDP GRO
- fix IP header access and skb lookup on Fast/frag0 UDP GRO
- ethtool: netlink: add missing netdev_features_change() call
- net: Update window_clamp if SOCK_RCVBUF is set
- igc: Fix returning wrong statistics
- ch_ktls: fix multiple leaks and corner cases in Chelsio TLS offload
- tunnels: Fix off-by-one in lower MTU bounds for ICMP/ICMPv6 replies
- r8169: disable hw csum for short packets on all chip versions
- vrf: Fix fast path output packet handling with async Netfilter
rules"
* tag 'net-5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits)
lan743x: fix use of uninitialized variable
net: udp: fix IP header access and skb lookup on Fast/frag0 UDP GRO
net: udp: fix UDP header access on Fast/frag0 UDP GRO
devlink: Avoid overwriting port attributes of registered port
vrf: Fix fast path output packet handling with async Netfilter rules
cosa: Add missing kfree in error path of cosa_write
net: switch to the kernel.org patchwork instance
ch_ktls: stop the txq if reaches threshold
ch_ktls: tcb update fails sometimes
ch_ktls/cxgb4: handle partial tag alone SKBs
ch_ktls: don't free skb before sending FIN
ch_ktls: packet handling prior to start marker
ch_ktls: Correction in middle record handling
ch_ktls: missing handling of header alone
ch_ktls: Correction in trimmed_len calculation
cxgb4/ch_ktls: creating skbs causes panic
ch_ktls: Update cheksum information
ch_ktls: Correction in finding correct length
cxgb4/ch_ktls: decrypted bit is not enough
net/x25: Fix null-ptr-deref in x25_connect
...
As the kernel never sets HCR_EL2.EnSCXT, accesses to SCXTNUM_ELx
will trap to EL2. Let's handle that as gracefully as possible
by injecting an UNDEF exception into the guest. This is consistent
with the guest's view of ID_AA64PFR0_EL1.CSV2 being at most 1.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201110141308.451654-4-maz@kernel.org
A large number of system register trap handlers only inject an
UNDEF exeption, and yet each class of sysreg seems to provide its
own, identical function.
Let's unify them all, saving us introducing yet another one later.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201110141308.451654-3-maz@kernel.org
We now expose ID_AA64PFR0_EL1.CSV2=1 to guests running on hosts
that are immune to Spectre-v2, but that don't have this field set,
most likely because they predate the specification.
However, this prevents the migration of guests that have started on
a host the doesn't fake this CSV2 setting to one that does, as KVM
rejects the write to ID_AA64PFR0_EL2 on the grounds that it isn't
what is already there.
In order to fix this, allow userspace to set this field as long as
this doesn't result in a promising more than what is already there
(setting CSV2 to 0 is acceptable, but setting it to 1 when it is
already set to 0 isn't).
Fixes: e1026237f9 ("KVM: arm64: Set CSV2 for guests on hardware unaffected by Spectre-v2")
Reported-by: Peng Liang <liangpeng10@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201110141308.451654-2-maz@kernel.org
Add configs to enable regulators that supply power to the SD card
on TI's J721e platform. These regulators are controlled by either
SoC gpios or gpios over i2c expander.
Changes to vmlinux size:
Before:
text data bss dec hex filename
20219067 10875634 523924 31618625 1e27641 vmlinux
After:
text data bss dec hex filename
20228755 10880422 524628 31633805 1e2b18d vmlinux
delta: 15180 (dec)
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Link: https://lore.kernel.org/r/20201103190821.30937-1-faiz_abbas@ti.com
Two carveout reserved memory nodes each have been added for each of the
R5F remote processor devices within both the MCU and MAIN domains for the
TI J721E EVM boards. These nodes are assigned to the respective rproc
device nodes as well. The first region will be used as the DMA pool for
the rproc device, and the second region will furnish the static carveout
regions for the firmware memory.
The current carveout addresses and sizes are defined statically for each
device. The R5F processors do not have an MMU, and as such require the
exact memory used by the firmwares to be set-aside. The firmware images
do not require any RSC_CARVEOUT entries in their resource tables either
to allocate the memory for firmware memory segments.
Note that the R5F1 carveouts are needed only if the R5F cluster is running
in Split (non-LockStep) mode. The reserved memory nodes can be disabled
later on if there is no use-case defined to use the corresponding
remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20201029033802.15366-9-s-anna@ti.com
Add the required 'mboxes' property to all the R5F processors for the
TI J721E common processor board. The mailboxes and some shared memory
are required for running the Remote Processor Messaging (RPMsg) stack
between the host processor and each of the R5Fs. The nodes are therefore
added in the common k3-j721e-som-p0.dtsi file so that all of these can
be co-located.
The chosen sub-mailboxes match the values used in the current firmware
images. This can be changed, if needed, as per the system integration
needs after making appropriate changes on the firmware side as well.
Note that any R5F Core1 resources are needed and used only when that
R5F cluster is configured for Split-mode.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20201029033802.15366-8-s-anna@ti.com
The J721E SoCs have 3 dual-core Arm Cortex-R5F processor (R5FSS)
subsystems/clusters. One R5F cluster (MCU_R5FSS0) is present within
the MCU domain, and the remaining two clusters are present in the
MAIN domain (MAIN_R5FSS0 & MAIN_R5FSS1). Each of these can be
configured at boot time to be either run in a LockStep mode or in
an Asymmetric Multi Processing (AMP) fashion in Split-mode. These
subsystems have 64 KB each Tightly-Coupled Memory (TCM) internal
memories for each core split between two banks - ATCM and BTCM
(further interleaved into two banks). There are some IP integration
differences from standard Arm R5 clusters such as the absence of
an ACP port, presence of an additional TI-specific Region Address
Translater (RAT) module for translating 32-bit CPU addresses into
larger system bus addresses etc.
Add the DT nodes for these two MAIN domain R5F cluster/subsystems,
the two R5F cores are each added as child nodes to the corresponding
main cluster node. Both the clusters are configured to run in LockStep
mode by default, with the ATCMs enabled to allow the R5 cores to execute
code from DDR with boot-strapping code from ATCM. The inter-processor
communication between the main A72 cores and these processors is
achieved through shared memory and Mailboxes.
The following firmware names are used by default for these cores, and
can be overridden in a board dts file if needed:
MAIN R5FSS0 Core0: j7-main-r5f0_0-fw (both in LockStep and Split modes)
MAIN R5FSS0 Core1: j7-main-r5f0_1-fw (needed only in Split mode)
MAIN R5FSS1 Core0: j7-main-r5f1_0-fw (both in LockStep and Split modes)
MAIN R5FSS1 Core1: j7-main-r5f1_1-fw (needed only in Split mode)
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20201029033802.15366-7-s-anna@ti.com
The J721E SoCs have 3 dual-core Arm Cortex-R5F processor (R5FSS)
subsystems/clusters. One R5F cluster (MCU_R5FSS0) is present within
the MCU domain, and the remaining two clusters are present in the
MAIN domain (MAIN_R5FSS0 & MAIN_R5FSS1). Each of these can be
configured at boot time to be either run in a LockStep mode or in
an Asymmetric Multi Processing (AMP) fashion in Split-mode. These
subsystems have 64 KB each Tightly-Coupled Memory (TCM) internal
memories for each core split between two banks - ATCM and BTCM
(further interleaved into two banks). There are some IP integration
differences from standard Arm R5 clusters such as the absence of
an ACP port, presence of an additional TI-specific Region Address
Translater (RAT) module for translating 32-bit CPU addresses into
larger system bus addresses etc.
Add the DT node for the MCU domain R5F cluster/subsystem, the two
R5F cores are added as child nodes to the main cluster/subsystem node.
The cluster is configured to run in LockStep mode by default, with the
ATCMs enabled to allow the R5 cores to execute code from DDR with
boot-strapping code from ATCM. The inter-processor communication
between the main A72 cores and these processors is achieved through
shared memory and Mailboxes.
The following firmware names are used by default for these cores, and
can be overridden in a board dts file if needed:
MCU R5FSS0 Core0: j7-mcu-r5f0_0-fw (both in LockStep and Split modes)
MCU R5FSS0 Core1: j7-mcu-r5f0_1-fw (needed only in Split mode)
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20201029033802.15366-6-s-anna@ti.com
Add a reserved memory node to reserve a portion of the DDR memory to be
used for performing inter-processor communication between all the MCU R5F
remote processors running RTOS on all the TI AM654 boards. This memory
shall be exercised only if the MCU R5FSS cluster is configured for Split
mode. A single 1 MB of memory at 0xa2000000 is reserved for this purpose,
and this accounts for all the vrings and vring buffers between pair of
these R5F remote processors.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20201029033802.15366-5-s-anna@ti.com
The R5F processors do not have an MMU, and as such require the exact memory
used by the firmwares to be set-aside. Four carveout reserved memory nodes
have been added with two each (1 MB and 15 MB in size) used for each of the
MCU R5F remote processor devices on all the TI K3 AM65x boards. These nodes
are assigned to the respective rproc device nodes as well.
The current carveout addresses and sizes are defined statically for each
device. The first region will be used as the DMA pool for the rproc
device, and the second region will furnish the static carveout regions
for the firmware memory.
Note that the R5F1 carveouts are needed only if the corresponding R5F
cluster is running in Split (non-LockStep) mode. The corresponding
reserved memory nodes can be disabled later on if there is no use-case
defined to use the corresponding remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20201029033802.15366-4-s-anna@ti.com
Add the required 'mboxes' property to both the R5F processors on all the
TI K3 AM65x boards. The mailboxes and some shared memory are required
for running the Remote Processor Messaging (RPMsg) stack between the
host processor and each of the R5Fs. The chosen sub-mailboxes match the
values used in the current firmware images. This can be changed, if
needed, as per the system integration needs after making appropriate
changes on the firmware side as well.
Note that the R5F Core1 resources are needed and used only when the
R5F cluster is configured for Split-mode.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20201029033802.15366-3-s-anna@ti.com
The AM65x SoCs have a single dual-core Arm Cortex-R5F processor (R5FSS)
subsystem/cluster. This R5F cluster (MCU_R5FSS0) is present within the
MCU domain, and can be configured at boot time to be either run in a
LockStep mode or in an Asymmetric Multi Processing (AMP) fashion in
Split-mode. This subsystem has 64 KB each Tightly-Coupled Memory (TCM)
internal memories for each core split between two banks - TCMA and TCMB
(further interleaved into two banks). There are some IP integration
differences from standard Arm R5F clusters such as the absence of an ACP
port, presence of an additional TI-specific Region Address Translater
(RAT) module for translating 32-bit CPU addresses into larger system
bus addresses etc.
Add the DT node for this R5F cluster/subsystem, the two R5F cores are
added as child nodes to the main cluster node. The cluster is configured
to run in LockStep mode by default, with the ATCMs enabled to allow the
R5 cores to execute code from DDR with boot-strapping code from ATCM.
The inter-processor communication between the main A53 cores and these
processors is achieved through shared memory and Mailboxes.
The following firmware names are used by default for these cores, and
can be overridden in a board dts file if needed:
am65x-mcu-r5f0_0-fw (LockStep mode and for Core0 in Split mode)
am65x-mcu-r5f0_1-fw (Core1 in Split mode)
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20201029033802.15366-2-s-anna@ti.com
DSS is IO coherent on AM65, so we should mark it as such with
'dma-coherent' property in the DT file.
Fixes: fc539b90ed ("arm64: dts: ti: am654: Add DSS node")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Cc: stable@vger.kernel.org # v5.8+
Link: https://lore.kernel.org/r/20201102134650.55321-1-tomi.valkeinen@ti.com
Commit 8c96400d6a simplified the page-to-virt and virt-to-page
conversions, based on the assumption that struct page is always 64
bytes in size, in which case we can use a single signed shift to
perform the conversion (provided that the vmemmap array is placed
appropriately in the kernel VA space)
Unfortunately, this assumption turns out not to hold, and so we need
to revert part of this commit, and go back to an affine transformation.
Given that all the quantities involved are compile time constants,
this should not make any practical difference.
Fixes: 8c96400d6a ("arm64: mm: make vmemmap region a projection of the linear region")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20201110180511.29083-1-ardb@kernel.org
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Since commit 71b77a7a27 ("enetc: Migrate to PHYLINK and PCS_LYNX") the
network port of the Kontron sl28 board is broken. After the migration to
phylink the device tree has to specify the in-band-mode property. Add
it.
Fixes: 71b77a7a27 ("enetc: Migrate to PHYLINK and PCS_LYNX")
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20201109110436.5906-1-michael@walle.cc
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After many years of struggle, commit fa2d0aa969 ("mmc: core: Allow
setting slot index via device tree alias") finally allows the use of
aliases to number SD/MMC slots. Let's do that for sc7180 SoCs so that
if eMMC and SD are both used they have consistent numbers across boots
and kernel changes.
Picking numbers can be tricky. Do we call these "1" and "2" to match
the name in documentation or "0" and "1" with the assertion that we
should always start at 0 and count up?
While the "start counting at 0" makes sense if there are not already
well-defined numbers for all sd/mmc controllers, in the case of sc7180
there _are_ well defined numbers. IMO it is less confusing to use
those and match the docs.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201111073652.1.Ia5bccd9eab7d74ea1ea9a7780e3cdbf662f5a464@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
DMA controller binding describes the node name should be dma-controller
and not dma, so fix the node name
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201027164511.476312-10-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
DMA controller binding describes the node name should be dma-controller
and not dma, so fix the node name
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201027164511.476312-9-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
DMA controller binding describes the node name should be dma-controller
and not dma, so fix the node name
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201027164511.476312-8-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
DMA controller binding describes the node name should be dma-controller
and not dma, so fix the node name
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201027164511.476312-7-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
DMA controller binding describes the node name should be dma-controller
and not dma, so fix the node name
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201027164511.476312-6-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
DMA controller binding describes the node name should be dma-controller
and not dma, so fix the node name
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201027164511.476312-5-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
DMA controller binding describes the node name should be dma-controller
and not dma, so fix the node name
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201027164511.476312-4-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
DMA controller binding describes the node name should be dma-controller
and not dma, so fix the node name
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201027164511.476312-3-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
DMA controller binding describes the node name should be dma-controller
and not dma, so fix the node name
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201027164511.476312-2-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add device tree support for Microsoft Lumia 950 XL smartphone.
It is based on the msm8994 chipset and is able to boot Linux
using a custom EDK2 implementation. EL2 core startup is possible
with spin-table, but for now, we'll stick with PSCI.
The board currently supports:
* Screen console via EFIFB
* SDHCI
* I2C
* UART
* PSCI core bringup
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20201005150313.149754-12-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add cooling-cells property and the cooling maps for the gpu tzones
to support GPU cooling.
Signed-off-by: Akhil P Oommen <akhilpo@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1604054832-3114-2-git-send-email-akhilpo@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add configs for lazor rev2 and rev3. There are no relevant deltas
between rev1 and rev2, so just add the rev2 compatible string to the
rev1 config.
One important delta in rev3 is a switch of the power supply for the
onboard USB hub from 'pp3300_l7c' to 'pp3300_a' + a load switch. The
actual regulator switch is done by the patch 'arm64: dts: qcom:
sc7180-trogdor: Make pp3300_a the default supply for pp3300_hub',
since it affects the entire trogdor platform. Here we only add the
.dts files for lazor rev3 and replace the generic compatible entries
in the rev1 .dts files.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20201106140125.v3.1.I5a75056d573808f40fed22ab7d28ea6be5819f84@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The scripts/dtc/checks.c requires that the node have empty "dma-ranges"
property must have the same "#address-cells" and "#size-cells" values as
the parent node. Otherwise, the following warnings is reported:
arch/arm64/boot/dts/qcom/ipq6018.dtsi:185.3-14: Warning \
(dma_ranges_format): /soc:dma-ranges: empty "dma-ranges" property but \
its #address-cells (1) differs from / (2)
arch/arm64/boot/dts/qcom/ipq6018.dtsi:185.3-14: Warning \
(dma_ranges_format): /soc:dma-ranges: empty "dma-ranges" property but \
its #size-cells (1) differs from / (2)
Arnd Bergmann figured out why it's necessary:
Also note that the #address-cells=<1> means that any device under
this bus is assumed to only support 32-bit addressing, and DMA will
have to go through a slow swiotlb in the absence of an IOMMU.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20201016090833.1892-3-thunder.leizhen@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The modem firmware memory requirements vary between 32M/140M on
no-lte/lte skus respectively, so fixup the modem memory region
to reflect the requirements.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/1602786476-27833-1-git-send-email-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the camera clock controller node supported on SC7180.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/1604687907-25712-1-git-send-email-tdas@codeaurora.org
[bjorn: Dropped camcc include]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This adds a validation function that scans the entire boot memory and makes
sure that all early memory sections are online. This check is essential for
the memory notifier to work properly, as it cannot prevent any boot memory
from offlining, if all sections are not online to begin with. Although the
boot section scanning is selectively enabled with DEBUG_VM.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/1604896137-16644-4-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This enables MEM_OFFLINE memory event handling. It will help intercept any
possible error condition such as if boot memory some how still got offlined
even after an explicit notifier failure, potentially by a future change in
generic hot plug framework. This would help detect such scenarios and help
debug further. While here, also call out the first section being attempted
for offline or got offlined.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/1604896137-16644-3-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This moves memory notifier registration earlier in the boot process from
device_initcall() to early_initcall() which will help in guarding against
potential early boot memory offline requests. Even though there should not
be any actual offlinig requests till memory block devices are initialized
with memory_dev_init() but then generic init sequence might just change in
future. Hence an early registration for the memory event notifier would be
helpful. While here, just skip the registration if CONFIG_MEMORY_HOTREMOVE
is not enabled and also call out when memory notifier registration fails.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/1604896137-16644-2-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
As a hardening measure, we currently randomize the placement of
physical memory inside the linear region when KASLR is in effect.
Since the random offset at which to place the available physical
memory inside the linear region is chosen early at boot, it is
based on the memblock description of memory, which does not cover
hotplug memory. The consequence of this is that the randomization
offset may be chosen such that any hotplugged memory located above
memblock_end_of_DRAM() that appears later is pushed off the end of
the linear region, where it cannot be accessed.
So let's limit this randomization of the linear region to ensure
that this can no longer happen, by using the CPU's addressable PA
range instead. As it is guaranteed that no hotpluggable memory will
appear that falls outside of that range, we can safely put this PA
range sized window anywhere in the linear region.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Steven Price <steven.price@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20201014081857.3288-1-ardb@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Mapping between IPI type index and its string is direct without requiring
an additional offset. Hence the existing macro S(x, s) is now redundant
and can just be dropped. This also makes the code clean and simple.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/1604921916-23368-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Use hyphens instead of underscores in the Exynos5433 node names which is
expected by naming convention, multiple dtschema files and pointed out
by dtc W=2 builds.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201105184506.215648-6-krzk@kernel.org
Set the qcom,adreno-smmu compatible string for the GPU SMMU to enable
split pagetables and per-instance pagetables for drm/msm.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200905200454.240929-21-robdclark@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Set the qcom,adreno-smmu compatible string for the GPU SMMU to enable
split pagetables and per-instance pagetables for drm/msm.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201109184728.2463097-5-jcrouse@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Depending on configuration options and specific code paths, we either
use the empty_zero_page or the configuration-dependent reserved_ttbr0
as a reserved value for TTBR{0,1}_EL1.
To simplify this code, let's always allocate and use the same
reserved_pg_dir, replacing reserved_ttbr0. Note that this is allocated
(and hence pre-zeroed), and is also marked as read-only in the kernel
Image mapping.
Keeping this separate from the empty_zero_page potentially helps with
robustness as the empty_zero_page is used in a number of cases where a
failure to map it read-only could allow it to become corrupted.
The (presently unused) swapper_pg_end symbol is also removed, and
comments are added wherever we rely on the offsets between the
pre-allocated pg_dirs to keep these cases easily identifiable.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201103102229.8542-1-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The kprobe_step_ctx (kcb->ss_ctx) has ss_pending and match_addr, but
those are redundant because those can be replaced by KPROBE_HIT_SS and
&cur_kprobe->ainsn.api.insn[1] respectively.
To simplify the code, remove the kprobe_step_ctx.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201103134900.337243-2-jean-philippe@linaro.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch reworks PINCTRL_MSM to be a visible option, and
instead of having the various SoC specific drivers select
PINCTRL_MSM, this switches those configs to depend on
PINCTRL_MSM.
This is useful, as it will be needed in order to cleanly support
having the qcom-scm driver, which pinctrl-msm calls into,
configured as a module. Without this change, we would eventually
have to add dependency lines to every config that selects
PINCTRL_MSM, and that would becomes a maintenance headache.
We also add PINCTRL_MSM to the arm64 defconfig to avoid
surprises as otherwise PINCTRL_MSM/IPQ* options previously
enabled, will be off.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Maulik Shah <mkshah@codeaurora.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: iommu@lists.linux-foundation.org
Cc: linux-gpio@vger.kernel.org
Link: https://lore.kernel.org/r/20201106042710.55979-1-john.stultz@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl+oiOgeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGKBQIAJw6oad/FA7j9OO2
dMoaXb8UaBehGWgW2rdfWrFPV5v0DBnp/GkdRpLoZIjV3W4mBfnog7bIa4Eswlxo
Y8sZxo5/3JlgJQUkHvzR1TYk5z61lHkUw9Kj/cCyx6YdbjSl19AfFsnhQVVMuyp9
TXL2c7hxkHlw8eBGrymVu0Ip7Zq0x8O2g+8nQpmRcvaR6SBuSHdikDF/iWCtU1YW
wpk5eWEVaAO67keZOz6b+aCFHqjFX+1dUBBuPnslucYLR73Qi16hfaU9pebe97Gb
lX/MJ1bR9BeRp314cF0PYbm4WhKjRLudHOFJH8x3dj/BiYNrFK3SJGLiiTwsrAZ8
kytU0Xs=
=Ke/D
-----END PGP SIGNATURE-----
Merge v5.10-rc3 into drm-next
We need commit f8f6ae5d07 ("mm: always have io_remap_pfn_range() set
pgprot_decrypted()") to be able to merge Jason's cleanup patch.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit ce3d31ad3c ("arm64/smp: Move rcu_cpu_starting() earlier") ensured
that RCU is informed early about incoming CPUs that might end up calling
into printk() before they are online. However, if such a CPU fails the
early CPU feature compatibility checks in check_local_cpu_capabilities(),
then it will be powered off or parked without informing RCU, leading to
an endless stream of stalls:
| rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
| rcu: 2-O...: (0 ticks this GP) idle=002/1/0x4000000000000000 softirq=0/0 fqs=2593
| (detected by 0, t=5252 jiffies, g=9317, q=136)
| Task dump for CPU 2:
| task:swapper/2 state:R running task stack: 0 pid: 0 ppid: 1 flags:0x00000028
| Call trace:
| ret_from_fork+0x0/0x30
Ensure that the dying CPU invokes rcu_report_dead() prior to being powered
off or parked.
Cc: Qian Cai <cai@redhat.com>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Suggested-by: Qian Cai <cai@redhat.com>
Link: https://lore.kernel.org/r/20201105222242.GA8842@willie-the-truck
Link: https://lore.kernel.org/r/20201106103602.9849-3-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
cpu_psci_cpu_die() is called in the context of the dying CPU, which
will no longer be online or tracked by RCU. It is therefore not generally
safe to call printk() if the PSCI "cpu off" request fails, so remove the
pr_crit() invocation.
Cc: Qian Cai <cai@redhat.com>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20201106103602.9849-2-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Sparse gets cross about us returning 0 from image_load(), which has a
return type of 'void *':
>> arch/arm64/kernel/kexec_image.c:130:16: sparse: sparse: Using plain integer as NULL pointer
Return NULL instead, as we don't use the return value for anything if it
does not indicate an error.
Cc: Benjamin Gwin <bgwin@google.com>
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 108aa50365 ("arm64: kexec_file: try more regions if loading segments fails")
Link: https://lore.kernel.org/r/202011091736.T0zH8kaC-lkp@intel.com
Signed-off-by: Will Deacon <will@kernel.org>
In a surprising turn of events, it transpires that CPU capabilities
configured as ARM64_CPUCAP_WEAK_LOCAL_CPU_FEATURE are never set as the
result of late-onlining. Therefore our handling of erratum 1418040 does
not get activated if it is not required by any of the boot CPUs, even
though we allow late-onlining of an affected CPU.
In order to get things working again, replace the cpus_have_const_cap()
invocation with an explicit check for the current CPU using
this_cpu_has_cap().
Cc: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201106114952.10032-1-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
kvm_coproc.h used to serve as a compatibility layer for the files
shared between the 32 and 64 bit ports.
Another one bites the dust...
Signed-off-by: Marc Zyngier <maz@kernel.org>
Similarly to what has been done on the cp15 front, repaint the
debug registers to use their AArch64 counterparts. This results
in some simplification as we can remove the 32bit-specific
accessors.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Move all the cp15 registers over to their AArch64 counterpart.
This requires the annotation of a few of them (such as the usual
DFAR/IFAR vs FAR_EL1), and a new helper that generates mask/shift
pairs for the various configurations.
Signed-off-by: Marc Zyngier <maz@kernel.org>
In order to deal with the few AArch32 system registers that map to
only a particular half of their AArch64 counterpart (such as DFAR
and IFAR being colocated in FAR_EL1), let's add an optional annotation
to the sysreg descriptor structure, indicating whether a register
maps to the upper or lower 32bits of a register.
Nothing is using these annotation yet.
Signed-off-by: Marc Zyngier <maz@kernel.org>
The use of the AArch32-specific accessors have always been a bit
annoying on 64bit, and it is time for a change.
Let's move the AArch32 exception injection over to the AArch64 encoding,
which requires us to split the two halves of FAR_EL1 into DFAR and IFAR.
This enables us to drop the preempt_disable() games on VHE, and to kill
the last user of the vcpu_cp15() macro.
Signed-off-by: Marc Zyngier <maz@kernel.org>
ARMv8.2 introduced TTBCR2, which shares TCR_EL1 with TTBCR.
Gracefully handle traps to this register when HCR_EL2.TVM is set.
Cc: stable@vger.kernel.org
Reported-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The only use of the register mapping code was for the sake of the LR
mapping, which we trivially solved in a previous patch. Get rid of
the whole thing now.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Jagan Teki