The nvme pci driver prepares its devices for power loss during suspend
by shutting down the controllers. The power setting is deferred to
pci driver's power management before the platform removes power. The
suspend-to-idle mode, however, does not remove power.
NVMe devices that implement host managed power settings can achieve
lower power and better transition latencies than using generic PCI power
settings. Try to use this feature if the platform is not involved with
the suspend. If successful, restore the previous power state on resume.
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
[hch: fixed the compilation for the !CONFIG_PM_SLEEP case]
Signed-off-by: Christoph Hellwig <hch@lst.de>
NVMe uses PRPs (or optionally unlimited SGLs) for data transfers and
has no specific limit for a single DMA segement. Limiting the size
will cause problems because the block layer assumes PRP-ish devices
using a virt boundary mask don't have a segment limit. And while this
is true, we also really need to tell the DMA mapping layer about it,
otherwise dma-debug will trip over it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A controller with multiple namespaces may have multiple request_queues with
their own timeout work. If a controller fails with IO outstanding to
diffent namespaces, each request queue may attempt to handle it, so
ensure there is no previously scheduled timeout work executing prior to
starting controller initialization by synchronizing with each queue.
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
The reset_work waits for queued IO to complete before setting the
controller to live. If any of these times out and requeues, we won't be
able to restart the controller because the reset_work is already running.
Flush all entered requests to a failed completion if a timeout occurs
in the connecting state, and ensure the controller can't transition to
the live state after we've unblocked it from waiting for completions.
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
The reset state doesn't dispatch commands that it needs to wait for
anymore. If a timeout occurs in this state, the reset work is already
disabling the controller, so just reset the request's timer.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
If a controller disabling didn't start a freeze, don't wait for the
operation to complete.
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/nvme/host/pci.c: In function ‘nvme_timeout’:
drivers/nvme/host/pci.c:1298:12: warning: this statement may fall through [-Wimplicit-fallthrough=]
shutdown = true;
~~~~~~~~~^~~~~~
drivers/nvme/host/pci.c:1299:2: note: here
case NVME_CTRL_CONNECTING:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The spec states:
"The settings are not retained across a Controller Level Reset"
Therefore the driver must enable the shadow doorbell, after each reset.
This was caught while testing the nvme driver over upcoming nvme-mdev
device.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Minwoo Im <minwoo.im@samsung.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Most command aren't PCIe specific, so move the size checking for them
to core.c
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
All the NVMe command has 64bytes fixed size so that it has been assured
with BUILD_BUG_ON(). The remaining command structures in linux/nvme.h
also need to be checked here.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Variable "n" will be assigned once kstrtoint() succeeds, otherwise it
will not be referred because kstrtoint() will return an error which
means go out from this function.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Just like IO queues, the admin queue also will not be restarted after a
controller shutdown. Unquiesce this queue so that we do not block
request dispatch on a permanently disabled controller.
Reported-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
We do not restart a controller in a deleting state for timeout errors.
When in this state, unblock potential request dispatchers with failed
completions by shutting down the controller on timeout detection.
Reported-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The shortcut for single segment SGL requests did not set the PSDT field
to mark the request as using SGLs.
Fixes: 297910571f ("nvme-pci: optimize mapping single segment requests using SGLs")
Signed-off-by: Klaus Birkelund Jensen <klaus.jensen@cnexlabs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Remove two pointless local variables, remove ret assignment that is
never used, move the use_sgl initialization closer to where it is used.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
If the controller supports SGLs we can take another short cut for single
segment request, given that we can always map those without another
indirection structure, and thus don't need to create a scatterlist
structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
If a request is single segment and fits into one or two PRP entries we
do not have to create a scatterlist for it, but can just map the bio_vec
directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
We'll have a better way to optimize for small I/O that doesn't
require it soon, so remove the existing inline_sg case to make that
optimization easier to implement.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
This prepares for some bigger changes to the data mapping helpers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
We always have exactly one segment, so we can simply call dma_map_bvec.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
This mirrors how nvme_map_pci is called and will allow simplifying some
checks in nvme_unmap_pci later on.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
This means we now have a function that undoes everything nvme_map_data
does and we can simplify the error handling a bit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Cleaning up the command setup isn't related to unmapping data, and
disentangling them will simplify error handling a bit down the road.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
nvme_init_iod should really be split into two parts: initialize a few
general iod fields, which can easily be done at the beginning of
nvme_queue_rq, and allocating the scatterlist if needed, which logically
belongs into nvme_map_data with the code making use of it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
We don't need to save the dma device as it's not used in the hot path
and hasn't in a long time. Shrink the struct nvme_queue removing this
unnecessary member.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
A negative value for the cq_vector used to mean the queue is either
disabled or a polled queue. However, we have a queue enabled flag,
so the cq_vector had been serving double duty.
Don't overload the meaning of cq_vector. Use a flag specific to the
polled queues instead.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAlyL124QHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgptsxD/42slmoE5TC3vwXcgMBEilrjIHCns6O4Leo
0r8Awdwil8QkVDphfAWsgkTBjRPUNKv4cCg2kG4VEzAy62YSutUWPeqJZwLOpGDI
kji9XI6WLqwQ/VhDFwEln9G+xWDUQxds5PZDomlzLpjiNqkFArwwsPFnJbshH4fB
U6kZrhVSLfvJHIJmC9H4RIWuTEwUH1yFSvzzMqDOOyvRon2g/A2YlHb2KhSCaJPq
1b0jbhyR0GVP0EH1FdeKvNYFZfvXXSPAbxDN1CEtW/Lq8WxXeoaCj390tC+gL7yQ
WWHntvUoVU/weWudbT3tVsYgpI91KfPM5OuWTDGod6lFwHrI5X91Pao3KYUGPb9d
cwvNBOlkNqR1ENZOGTgxLeKwiwV7G1DIjvsaijRQJhGy4Uw4RkM/YEct9JHxWBIF
x4ZuSVUVZ5Y3zNPC945iJ6Z5feOz/UO9bQL00oimu0c0JhAp++3pHWAFJEMQ8q1a
0IRifkeUyhf0p9CIVPDnUzmNgSBglFkAVTPVAWySBVDU+v0/GoNcYwTzPq4cgPrF
UJEIlx+RdDpKKmCqBvKjtx4w7BC1lCebL/1ZJrbARNO42djt8xeuyvKw0t+MYVTZ
UsvLX72tXwUIbj0IZZGuz+8uSGD4ddDs8+x486FN4oaCPf36FUnnkOZZkhjV/KQA
vsZNrNNZpw==
=qBae
-----END PGP SIGNATURE-----
Merge tag 'for-5.1/block-post-20190315' of git://git.kernel.dk/linux-block
Pull more block layer changes from Jens Axboe:
"This is a collection of both stragglers, and fixes that came in after
I finalized the initial pull. This contains:
- An MD pull request from Song, with a few minor fixes
- Set of NVMe patches via Christoph
- Pull request from Konrad, with a few fixes for xen/blkback
- pblk fix IO calculation fix (Javier)
- Segment calculation fix for pass-through (Ming)
- Fallthrough annotation for blkcg (Mathieu)"
* tag 'for-5.1/block-post-20190315' of git://git.kernel.dk/linux-block: (25 commits)
blkcg: annotate implicit fall through
nvme-tcp: support C2HData with SUCCESS flag
nvmet: ignore EOPNOTSUPP for discard
nvme: add proper write zeroes setup for the multipath device
nvme: add proper discard setup for the multipath device
nvme: remove nvme_ns_config_oncs
nvme: disable Write Zeroes for qemu controllers
nvmet-fc: bring Disconnect into compliance with FC-NVME spec
nvmet-fc: fix issues with targetport assoc_list list walking
nvme-fc: reject reconnect if io queue count is reduced to zero
nvme-fc: fix numa_node when dev is null
nvme-fc: use nr_phys_segments to determine existence of sgl
nvme-loop: init nvmet_ctrl fatal_err_work when allocate
nvme: update comment to make the code easier to read
nvme: put ns_head ref if namespace fails allocation
nvme-trace: fix cdw10 buffer overrun
nvme: don't warn on block content change effects
nvme: add get-feature to admin cmds tracer
md: Fix failed allocation of md_register_thread
It's wrong to add len to sector_nr in raid10 reshape twice
...
Qemu started out with a broken implementation of Write Zeroes written
by yours truly. Disable Write Zeroes on qemu for now, eventually
we need to go back and make all the qemu quirks version specific,
but that is left for another time.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Tested-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=VBaU
-----END PGP SIGNATURE-----
Merge tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"Not a huge amount of changes in this round, the biggest one is that we
finally have Mings multi-page bvec support merged. Apart from that,
this pull request contains:
- Small series that avoids quiescing the queue for sysfs changes that
match what we currently have (Aleksei)
- Series of bcache fixes (via Coly)
- Series of lightnvm fixes (via Mathias)
- NVMe pull request from Christoph. Nothing major, just SPDX/license
cleanups, RR mp policy (Hannes), and little fixes (Bart,
Chaitanya).
- BFQ series (Paolo)
- Save blk-mq cpu -> hw queue mapping, removing a pointer indirection
for the fast path (Jianchao)
- fops->iopoll() added for async IO polling, this is a feature that
the upcoming io_uring interface will use (Christoph, me)
- Partition scan loop fixes (Dongli)
- mtip32xx conversion from managed resource API (Christoph)
- cdrom registration race fix (Guenter)
- MD pull from Song, two minor fixes.
- Various documentation fixes (Marcos)
- Multi-page bvec feature. This brings a lot of nice improvements
with it, like more efficient splitting, larger IOs can be supported
without growing the bvec table size, and so on. (Ming)
- Various little fixes to core and drivers"
* tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block: (117 commits)
block: fix updating bio's front segment size
block: Replace function name in string with __func__
nbd: propagate genlmsg_reply return code
floppy: remove set but not used variable 'q'
null_blk: fix checking for REQ_FUA
block: fix NULL pointer dereference in register_disk
fs: fix guard_bio_eod to check for real EOD errors
blk-mq: use HCTX_TYPE_DEFAULT but not 0 to index blk_mq_tag_set->map
block: optimize bvec iteration in bvec_iter_advance
block: introduce mp_bvec_for_each_page() for iterating over page
block: optimize blk_bio_segment_split for single-page bvec
block: optimize __blk_segment_map_sg() for single-page bvec
block: introduce bvec_nth_page()
iomap: wire up the iopoll method
block: add bio_set_polled() helper
block: wire up block device iopoll method
fs: add an iopoll method to struct file_operations
loop: set GENHD_FL_NO_PART_SCAN after blkdev_reread_part()
loop: do not print warn message if partition scan is successful
block: bounce: make sure that bvec table is updated
...
Pull irq updates from Thomas Gleixner:
"The interrupt departement delivers this time:
- New infrastructure to manage NMIs on platforms which have a sane
NMI delivery, i.e. identifiable NMI vectors instead of a single
lump.
- Simplification of the interrupt affinity management so drivers
don't have to implement ugly loops around the PCI/MSI enablement.
- Speedup for interrupt statistics in /proc/stat
- Provide a function to retrieve the default irq domain
- A new interrupt controller for the Loongson LS1X platform
- Affinity support for the SiFive PLIC
- Better support for the iMX irqsteer driver
- NUMA aware memory allocations for GICv3
- The usual small fixes, improvements and cleanups all over the
place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
irqchip/imx-irqsteer: Add multi output interrupts support
irqchip/imx-irqsteer: Change to use reg_num instead of irq_group
dt-bindings: irq: imx-irqsteer: Add multi output interrupts support
dt-binding: irq: imx-irqsteer: Use irq number instead of group number
irqchip/brcmstb-l2: Use _irqsave locking variants in non-interrupt code
irqchip/gicv3-its: Use NUMA aware memory allocation for ITS tables
irqdomain: Allow the default irq domain to be retrieved
irqchip/sifive-plic: Implement irq_set_affinity() for SMP host
irqchip/sifive-plic: Differentiate between PLIC handler and context
irqchip/sifive-plic: Add warning in plic_init() if handler already present
irqchip/sifive-plic: Pre-compute context hart base and enable base
PCI/MSI: Remove obsolete sanity checks for multiple interrupt sets
genirq/affinity: Remove the leftovers of the original set support
nvme-pci: Simplify interrupt allocation
genirq/affinity: Add new callback for (re)calculating interrupt sets
genirq/affinity: Store interrupt sets size in struct irq_affinity
genirq/affinity: Code consolidation
irqchip/irq-sifive-plic: Check and continue in case of an invalid cpuid.
irqchip/i8259: Fix shutdown order by moving syscore_ops registration
dt-bindings: interrupt-controller: loongson ls1x intc
...
Update license to use SPDX-License-Identifier instead of verbose license
text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
This patch avoids that the compiler complains about 'ret' being set
but not being used when building with W=1.
Fixes: 3b6592f70a ("nvme: utilize two queue maps, one for reads and one for writes") # v5.0-rc1
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The NVME PCI driver contains a tedious mechanism for interrupt
allocation, which is necessary to adjust the number and size of interrupt
sets to the maximum available number of interrupts which depends on the
underlying PCI capabilities and the available CPU resources.
It works around the former short comings of the PCI and core interrupt
allocation mechanims in combination with interrupt sets.
The PCI interrupt allocation function allows to provide a maximum and a
minimum number of interrupts to be allocated and tries to allocate as
many as possible. This worked without driver interaction as long as there
was only a single set of interrupts to handle.
With the addition of support for multiple interrupt sets in the generic
affinity spreading logic, which is invoked from the PCI interrupt
allocation, the adaptive loop in the PCI interrupt allocation did not
work for multiple interrupt sets. The reason is that depending on the
total number of interrupts which the PCI allocation adaptive loop tries
to allocate in each step, the number and the size of the interrupt sets
need to be adapted as well. Due to the way the interrupt sets support was
implemented there was no way for the PCI interrupt allocation code or the
core affinity spreading mechanism to invoke a driver specific function
for adapting the interrupt sets configuration.
As a consequence the driver had to implement another adaptive loop around
the PCI interrupt allocation function and calling that with maximum and
minimum interrupts set to the same value. This ensured that the
allocation either succeeded or immediately failed without any attempt to
adjust the number of interrupts in the PCI code.
The core code now allows drivers to provide a callback to recalculate the
number and the size of interrupt sets during PCI interrupt allocation,
which in turn allows the PCI interrupt allocation function to be called
in the same way as with a single set of interrupts. The PCI code handles
the adaptive loop and the interrupt affinity spreading mechanism invokes
the driver callback to adapt the interrupt set configuration to the
current loop value. This replaces the adaptive loop in the driver
completely.
Implement the NVME specific callback which adjusts the interrupt sets
configuration and remove the adaptive allocation loop.
[ tglx: Simplify the callback further and restore the dropped adjustment of
number of sets ]
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: linux-nvme@lists.infradead.org
Cc: linux-pci@vger.kernel.org
Cc: Keith Busch <keith.busch@intel.com>
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Shivasharan Srikanteshwara <shivasharan.srikanteshwara@broadcom.com>
Link: https://lkml.kernel.org/r/20190216172228.602546658@linutronix.de
The interrupt affinity spreading mechanism supports to spread out
affinities for one or more interrupt sets. A interrupt set contains one
or more interrupts. Each set is mapped to a specific functionality of a
device, e.g. general I/O queues and read I/O queus of multiqueue block
devices.
The number of interrupts per set is defined by the driver. It depends on
the total number of available interrupts for the device, which is
determined by the PCI capabilites and the availability of underlying CPU
resources, and the number of queues which the device provides and the
driver wants to instantiate.
The driver passes initial configuration for the interrupt allocation via
a pointer to struct irq_affinity.
Right now the allocation mechanism is complex as it requires to have a
loop in the driver to determine the maximum number of interrupts which
are provided by the PCI capabilities and the underlying CPU resources.
This loop would have to be replicated in every driver which wants to
utilize this mechanism. That's unwanted code duplication and error
prone.
In order to move this into generic facilities it is required to have a
mechanism, which allows the recalculation of the interrupt sets and
their size, in the core code. As the core code does not have any
knowledge about the underlying device, a driver specific callback will
be added to struct affinity_desc, which will be invoked by the core
code. The callback will get the number of available interupts as an
argument, so the driver can calculate the corresponding number and size
of interrupt sets.
To support this, two modifications for the handling of struct irq_affinity
are required:
1) The (optional) interrupt sets size information is contained in a
separate array of integers and struct irq_affinity contains a
pointer to it.
This is cumbersome and as the maximum number of interrupt sets is small,
there is no reason to have separate storage. Moving the size array into
struct affinity_desc avoids indirections and makes the code simpler.
2) At the moment the struct irq_affinity pointer which is handed in from
the driver and passed through to several core functions is marked
'const'.
With the upcoming callback to recalculate the number and size of
interrupt sets, it's necessary to remove the 'const'
qualifier. Otherwise the callback would not be able to update the data.
Implement #1 and store the interrupt sets size in 'struct irq_affinity'.
No functional change.
[ tglx: Fixed the memcpy() size so it won't copy beyond the size of the
source. Fixed the kernel doc comments for struct irq_affinity and
de-'This patch'-ed the changelog ]
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: linux-nvme@lists.infradead.org
Cc: linux-pci@vger.kernel.org
Cc: Keith Busch <keith.busch@intel.com>
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Shivasharan Srikanteshwara <shivasharan.srikanteshwara@broadcom.com>
Link: https://lkml.kernel.org/r/20190216172228.423723127@linutronix.de
The reset work holds a mutex to prevent races with removal modifying the
same resources, but was unlocking only on success. Unlock on failure
too.
Fixes: 5c959d73db ("nvme-pci: fix rapid add remove sequence")
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
A surprise removal may fail to tear down request queues if it is racing
with the initial asynchronous probe. If that happens, the remove path
won't see the queue resources to tear down, and the controller reset
path may create a new request queue on a removed device, but will not
be able to make forward progress, deadlocking the pci removal.
Protect setting up non-blocking resources from a shutdown by holding the
same mutex, and transition to the CONNECTING state after these resources
are initialized so the probe path may see the dead controller state
before dispatching new IO.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=202081
Reported-by: Alex Gagniuc <Alex_Gagniuc@Dellteam.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Tested-by: Alex Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When -ENOSPC is returned from pci_alloc_irq_vectors_affinity(),
we still try to allocate multiple irq vectors again, so irq queues
covers the admin queue actually. But we don't consider that, then
number of the allocated irq vector may be same with sum of
io_queues[HCTX_TYPE_DEFAULT] and io_queues[HCTX_TYPE_READ], this way
is obviously wrong, and finally breaks nvme_pci_map_queues(), and
warning from pci_irq_get_affinity() is triggered.
IRQ queues should cover admin queues, this patch makes this
point explicitely in nvme_calc_io_queues().
We got severl boot failure internal report on aarch64, so please
consider to fix it in v4.20.
Fixes: 6451fe73fa ("nvme: fix irq vs io_queue calculations")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Tested-by: fin4478 <fin4478@hotmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=OFV3
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20190112' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- NVMe pull request from Christoph, with little fixes all over the map
- Loop caching fix for offset/bs change (Jaegeuk Kim)
- Block documentation tweaks (Jeff, Jon, Weiping, John)
- null_blk zoned tweak (John)
- ahch mvebu suspend/resume support. Should have gone into the merge
window, but there was some confusion on which tree had it. (Miquel)
* tag 'for-linus-20190112' of git://git.kernel.dk/linux-block: (22 commits)
ata: ahci: mvebu: request PHY suspend/resume for Armada 3700
ata: ahci: mvebu: add Armada 3700 initialization needed for S2RAM
ata: ahci: mvebu: do Armada 38x configuration only on relevant SoCs
ata: ahci: mvebu: remove stale comment
ata: libahci_platform: comply to PHY framework
loop: drop caches if offset or block_size are changed
block: fix kerneldoc comment for blk_attempt_plug_merge()
nvme: don't initlialize ctrl->cntlid twice
nvme: introduce NVME_QUIRK_IGNORE_DEV_SUBNQN
nvme: pad fake subsys NQN vid and ssvid with zeros
nvme-multipath: zero out ANA log buffer
nvme-fabrics: unset write/poll queues for discovery controllers
nvme-tcp: don't ask if controller is fabrics
nvme-tcp: remove dead code
nvme-pci: fix out of bounds access in nvme_cqe_pending
nvme-pci: rerun irq setup on IO queue init errors
nvme-pci: use the same attributes when freeing host_mem_desc_bufs.
nvme-pci: fix the wrong setting of nr_maps
block: doc: add slice_idle_us to bfq documentation
block: clarify documentation for blk_{start|finish}_plug
...
If a device provides an NQN it is expected to be globally unique.
Unfortunately some firmware revisions for Intel 760p/Pro 7600p devices did
not satisfy this requirement. In these circumstances if a system has >1
affected device then only one device is enabled. If this quirk is enabled
then the device supplied subnqn is ignored and we fallback to generating
one as if the field was empty. In this case we also suppress the version
check so we don't print a warning when the quirk is enabled.
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: James Dingwall <james@dingwall.me.uk>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There is an out of bounds array access in nvme_cqe_peding().
When enable irq_thread for nvme interrupt, there is racing between the
nvmeq->cq_head updating and reading.
nvmeq->cq_head is updated in nvme_update_cq_head(), if nvmeq->cq_head
equals nvmeq->q_depth and before its value set to zero, nvme_cqe_pending()
uses its value as an array index, the index will be out of bounds.
Signed-off-by: Hongbo Yao <yaohongbo@huawei.com>
[hch: slight coding style update]
Signed-off-by: Christoph Hellwig <hch@lst.de>
When using HMB the PCIe host driver allocates host_mem_desc_bufs using
dma_alloc_attrs() but frees them using dma_free_coherent(). Use the
correct dma_free_attrs() function to free the buffers.
Signed-off-by: Liviu Dudau <liviu@dudau.co.uk>
Signed-off-by: Christoph Hellwig <hch@lst.de>
We only set the nr_maps to 3 if poll queues are supported.
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Export the disk name, queue id, sq_head, sq_tail to a trace event in
completion handling.
Usage example:
cd /sys/kernel/debug/tracing/events/nvme/nvme_sq
echo 'disk=="nvme1n1"' > filter
echo 1 > enable
cat /sys/kernel/debug/tracing/trace_pipe
Signed-off-by: yupeng <yupeng0921@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Keith Busch <keith.busch@intel.com>
[hch: slight formatting tweaks, use standard nvme tracepoint
conventions]
Signed-off-by: Christoph Hellwig <hch@lst.de>
wip
By duplicating the nvme_process_cq in both branches we keep the
sparse lock context checking happy, so do it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
The block layer now enables polling support on a queue if nr_maps
includes the poll map, so we should only set that if we actually
support poll queues.
Fixes: 6544d229bf ("block: enable polling by default if a poll map is initalized")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Now that the block layer checks if a queue map has any queues inside
it there is no more reason to duplicate the maps for the non-default
types.
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Guenter reported an boot hang issue on HPPA after we default to 0 poll
queues. We have two issues in the queue count calculations:
1) We don't separate the poll queues from the read/write queues. This is
important, since the former doesn't need interrupts.
2) The adjust logic is broken.
Adjust the poll queue count before doing nvme_calc_io_queues(). The poll
queue count is only limited by the IO queue count we were able to get
from the controller, not failures in the IRQ allocation loop. This
leaves nvme_calc_io_queues() just adjusting the read/write queue map.
Reported-by: Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This avoids having to have differnet mq_ops for different setups
with or without poll queues.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that we can't poll regular, interrupt driven I/O queues there
is almost nothing that can race with an interrupt. The only
possible other contexts polling a CQ are the error handler and
queue shutdown, and both are so far off in the slow path that
we can simply use the big hammer of disabling interrupts.
With that we can stop taking the cq_lock for normal queues.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is the last place outside of nvme_irq that handles CQEs from
interrupt context, and thus is in the way of removing the cq_lock for
normal queues, and avoiding lockdep warnings on the poll queues, for
which we already take it without IRQ disabling.
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass the opcode for the delete SQ/CQ command as an argument instead of
the somewhat confusing pass loop.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We have three places that can poll for I/O completions on a normal
interrupt-enabled queue. All of them are in slow path code, so
consolidate them to a single helper that uses spin_lock_irqsave and
removes the fast path cqe_pending check.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This will allow us to simplify both the regular NVMe interrupt handler
and the upcoming aio poll code. In addition to that the separate
queues are generally a good idea for performance reasons.
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use a bit flag to mark if the SQ was allocated from the CMB, and clean
up the surrounding code a bit.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This gets rid of all the messing with cq_vector and the ->polled field
by using an atomic bitop to mark the queue enabled or not.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Having another indirect all in the fast path doesn't really help
in our post-spectre world. Also having too many queue type is just
going to create confusion, so I'd rather manage them centrally.
Note that the queue type naming and ordering changes a bit - the
first index now is the default queue for everything not explicitly
marked, the optional ones are read and poll queues.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Split the command submission and the SQ doorbell ring, and add the
doorbell ring as our ->commit_rqs() hook. This allows a list of
requests to be issued, with nvme only writing the SQ update when
it's necessary. This is more efficient if we have lists of requests
to issue, particularly on virtualized hardware, where writing the
SQ doorbell is more expensive than on real hardware. For those cases,
performance increases of 2-3x have been observed.
The use case for this is plugged IO, where blk-mq flushes a batch of
requests at the time.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We always pass in -1 now and none of the callers use the tag value,
remove the parameter.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If we want to support async IO polling, then we have to allow finding
completions that aren't just for the one we are looking for. Always pass
in -1 to the mq_ops->poll() helper, and have that return how many events
were found in this poll loop.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We need a better way of configuring this, and given that polling is
(still) a bit niche, let's default to using 0 poll queues. That way
we'll have the same read/write/poll behavior as 4.20, and users that
want to test/use polling are required to do manual configuration of the
number of poll queues.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If we have separate poll queues, we know that they aren't using
interrupts. Hence we don't need to disable interrupts around
finding completions.
Provide a separate set of blk_mq_ops for such devices.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
At least on SPARC, if MSI/MSI-X isn't supported, we get EINVAL if
we ask for more than one vector. This isn't covered by our ENOSPC
check.
If we get EINVAL, decrease our ask to just one vector, instead of
bailing out in error.
Fixes: 3b6592f70a ("nvme: utilize two queue maps, one for reads and one for writes")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
NVMe always asks for io_queues + 1 worth of IRQ vectors, which
means that even when we scale all the way down, we still ask
for 2 vectors and get -ENOSPC in return if the system can't
support more than 1.
Getting just 1 vector is fine, it just means that we'll have
1 IO queue and 1 admin queue, with a shared vector between them.
Check for this case and don't add our + 1 if it happens.
Fixes: 3b6592f70a ("nvme: utilize two queue maps, one for reads and one for writes")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Adds support for defining a variable number of poll queues, currently
configurable with the 'poll_queues' module parameter. Defaults to
a single poll queue.
And now we finally have poll support without triggering interrupts!
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
NVMe does round-robin between queues by default, which means that
sharing a queue map for both reads and writes can be problematic
in terms of read servicing. It's much easier to flood the queue
with writes and reduce the read servicing.
Implement two queue maps, one for reads and one for writes. The
write queue count is configurable through the 'write_queues'
parameter.
By default, we retain the previous behavior of having a single
queue set, shared between reads and writes. Setting 'write_queues'
to a non-zero value will create two queue sets, one for reads and
one for writes, the latter using the configurable number of
queues (hardware queue counts permitting).
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is in preparation for allowing multiple sets of maps per
queue, if so desired.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The nvme pci driver had been adding its CMB resource to the P2P DMA
subsystem everytime on on a controller reset. This results in the
following warning:
------------[ cut here ]------------
nvme 0000:00:03.0: Conflicting mapping in same section
WARNING: CPU: 7 PID: 81 at kernel/memremap.c:155 devm_memremap_pages+0xa6/0x380
...
Call Trace:
pci_p2pdma_add_resource+0x153/0x370
nvme_reset_work+0x28c/0x17b1 [nvme]
? add_timer+0x107/0x1e0
? dequeue_entity+0x81/0x660
? dequeue_entity+0x3b0/0x660
? pick_next_task_fair+0xaf/0x610
? __switch_to+0xbc/0x410
process_one_work+0x1cf/0x350
worker_thread+0x215/0x3d0
? process_one_work+0x350/0x350
kthread+0x107/0x120
? kthread_park+0x80/0x80
ret_from_fork+0x1f/0x30
---[ end trace f7ea76ac6ee72727 ]---
nvme nvme0: failed to register the CMB
This patch fixes this by registering the CMB with P2P only once.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=58I4
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Fix ASPM link_state teardown on removal (Lukas Wunner)
- Fix misleading _OSC ASPM message (Sinan Kaya)
- Make _OSC optional for PCI (Sinan Kaya)
- Don't initialize ASPM link state when ACPI_FADT_NO_ASPM is set
(Patrick Talbert)
- Remove x86 and arm64 node-local allocation for host bridge structures
(Punit Agrawal)
- Pay attention to device-specific _PXM node values (Jonathan Cameron)
- Support new Immediate Readiness bit (Felipe Balbi)
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state
(Keith Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and
re-enumerate devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets
(Keith Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable
from cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments
(Keith Busch)
- Remove unused Netronome NFP32xx Device IDs (Jakub Kicinski)
- Use bitmap_zalloc() for dma_alias_mask (Andy Shevchenko)
- Add switch fall-through annotations (Gustavo A. R. Silva)
- Remove unused Switchtec quirk variable (Joshua Abraham)
- Fix pci.c kernel-doc warning (Randy Dunlap)
- Remove trivial PCI wrappers for DMA APIs (Christoph Hellwig)
- Add Intel GPU device IDs to spurious interrupt quirk (Bin Meng)
- Run Switchtec DMA aliasing quirk only on NTB endpoints to avoid
useless dmesg errors (Logan Gunthorpe)
- Update Switchtec NTB documentation (Wesley Yung)
- Remove redundant "default n" from Kconfig (Bartlomiej Zolnierkiewicz)
- Avoid panic when drivers enable MSI/MSI-X twice (Tonghao Zhang)
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
- Fix VMD AERSID quirk Device ID matching (Jon Derrick)
- Fix Cadence PHY handling during probe (Alan Douglas)
- Signal Cadence Endpoint interrupts via AXI region 0 instead of last
region (Alan Douglas)
- Write Cadence Endpoint MSI interrupts with 32 bits of data (Alan
Douglas)
- Remove redundant controller tests for "device_type == pci" (Rob
Herring)
- Document R-Car E3 (R8A77990) bindings (Tho Vu)
- Add device tree support for R-Car r8a7744 (Biju Das)
- Drop unused mvebu PCIe capability code (Thomas Petazzoni)
- Add shared PCI bridge emulation code (Thomas Petazzoni)
- Convert mvebu to use shared PCI bridge emulation (Thomas Petazzoni)
- Add aardvark Root Port emulation (Thomas Petazzoni)
- Support 100MHz/200MHz refclocks for i.MX6 (Lucas Stach)
- Add initial power management for i.MX7 (Leonard Crestez)
- Add PME_Turn_Off support for i.MX7 (Leonard Crestez)
- Fix qcom runtime power management error handling (Bjorn Andersson)
- Update TI dra7xx unaligned access errata workaround for host mode as
well as endpoint mode (Vignesh R)
- Fix kirin section mismatch warning (Nathan Chancellor)
- Remove iproc PAXC slot check to allow VF support (Jitendra Bhivare)
- Quirk Keystone K2G to limit MRRS to 256 (Kishon Vijay Abraham I)
- Update Keystone to use MRRS quirk for host bridge instead of open
coding (Kishon Vijay Abraham I)
- Refactor Keystone link establishment (Kishon Vijay Abraham I)
- Simplify and speed up Keystone link training (Kishon Vijay Abraham I)
- Remove unused Keystone host_init argument (Kishon Vijay Abraham I)
- Merge Keystone driver files into one (Kishon Vijay Abraham I)
- Remove redundant Keystone platform_set_drvdata() (Kishon Vijay
Abraham I)
- Rename Keystone functions for uniformity (Kishon Vijay Abraham I)
- Add Keystone device control module DT binding (Kishon Vijay Abraham
I)
- Use SYSCON API to get Keystone control module device IDs (Kishon
Vijay Abraham I)
- Clean up Keystone PHY handling (Kishon Vijay Abraham I)
- Use runtime PM APIs to enable Keystone clock (Kishon Vijay Abraham I)
- Clean up Keystone config space access checks (Kishon Vijay Abraham I)
- Get Keystone outbound window count from DT (Kishon Vijay Abraham I)
- Clean up Keystone outbound window configuration (Kishon Vijay Abraham
I)
- Clean up Keystone DBI setup (Kishon Vijay Abraham I)
- Clean up Keystone ks_pcie_link_up() (Kishon Vijay Abraham I)
- Fix Keystone IRQ status checking (Kishon Vijay Abraham I)
- Add debug messages for all Keystone errors (Kishon Vijay Abraham I)
- Clean up Keystone includes and macros (Kishon Vijay Abraham I)
- Fix Mediatek unchecked return value from devm_pci_remap_iospace()
(Gustavo A. R. Silva)
- Fix Mediatek endpoint/port matching logic (Honghui Zhang)
- Change Mediatek Root Port Class Code to PCI_CLASS_BRIDGE_PCI (Honghui
Zhang)
- Remove redundant Mediatek PM domain check (Honghui Zhang)
- Convert Mediatek to pci_host_probe() (Honghui Zhang)
- Fix Mediatek MSI enablement (Honghui Zhang)
- Add Mediatek system PM support for MT2712 and MT7622 (Honghui Zhang)
- Add Mediatek loadable module support (Honghui Zhang)
- Detach VMD resources after stopping root bus to prevent orphan
resources (Jon Derrick)
- Convert pcitest build process to that used by other tools (iio, perf,
etc) (Gustavo Pimentel)
* tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI: pcie: Remove redundant 'default n' from Kconfig
PCI: aardvark: Implement emulated root PCI bridge config space
PCI: mvebu: Convert to PCI emulated bridge config space
PCI: mvebu: Drop unused PCI express capability code
PCI: Introduce PCI bridge emulated config space common logic
PCI: vmd: Detach resources after stopping root bus
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
...
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
* pci/peer-to-peer:
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
PCI/P2PDMA: Add sysfs group to display p2pmem stats
PCI/P2PDMA: Support peer-to-peer memory
This is a cleanup patch doesn't change any functionality. It removes
the duplicate call to the blk_integrity_rq() in the nvme_map_data().
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
For P2P requests, we must use the pci_p2pmem_map_sg() function instead of
the dma_map_sg functions.
With that, we can then indicate PCI_P2P support in the request queue. For
this, we create an NVME_F_PCI_P2P flag which tells the core to set
QUEUE_FLAG_PCI_P2P in the request queue.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Register the CMB buffer as p2pmem and use the appropriate allocation
functions to create and destroy the IO submission queues.
If the CMB supports WDS and RDS, publish it for use as P2P memory by other
devices.
Kernels without CONFIG_PCI_P2PDMA will also no longer support NVMe CMB.
However, seeing the main use-cases for the CMB is P2P operations, this
seems like a reasonable dependency.
We drop the __iomem safety on the buffer seeing that, by convention, it's
safe to directly access memory mapped by memremap()/devm_memremap_pages().
Architectures where this is not safe will not be supported by memremap()
and therefore will not support PCI P2P and have no support for CMB.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
A removal waits for the reset_work to complete. If a surprise removal
occurs around the same time as an error triggered controller reset, and
reset work happened to dispatch a command to the removed controller, the
command won't be recovered since the timeout work doesn't do anything
during error recovery. We wouldn't want to wait for timeout handling
anyway, so this patch fixes this by disabling the controller and killing
admin queues prior to syncing with the reset_work.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch avoids that the kernel-doc tool complains about the
nvme_suspend_queue() function header when building with W=1.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
After bfcb79fca1 ("PCI/ERR: Run error recovery callbacks for all affected
devices"), AER errors are always cleared by the PCI core and drivers don't
need to do it themselves.
Remove calls to pci_cleanup_aer_uncorrect_error_status() from device
driver error recovery functions.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog, remove PCI core changes, remove unused variables]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In many architectures loads may be reordered with older stores to
different locations. In the nvme driver the following two operations
could be reordered:
- Write shadow doorbell (dbbuf_db) into memory.
- Read EventIdx (dbbuf_ei) from memory.
This can result in a potential race condition between driver and VM host
processing requests (if given virtual NVMe controller has a support for
shadow doorbell). If that occurs, then the NVMe controller may decide to
wait for MMIO doorbell from guest operating system, and guest driver may
decide not to issue MMIO doorbell on any of subsequent commands.
This issue is purely timing-dependent one, so there is no easy way to
reproduce it. Currently the easiest known approach is to run "Oracle IO
Numbers" (orion) that is shipped with Oracle DB:
orion -run advanced -num_large 0 -size_small 8 -type rand -simulate \
concat -write 40 -duration 120 -matrix row -testname nvme_test
Where nvme_test is a .lun file that contains a list of NVMe block
devices to run test against. Limiting number of vCPUs assigned to given
VM instance seems to increase chances for this bug to occur. On test
environment with VM that got 4 NVMe drives and 1 vCPU assigned the
virtual NVMe controller hang could be observed within 10-20 minutes.
That correspond to about 400-500k IO operations processed (or about
100GB of IO read/writes).
Orion tool was used as a validation and set to run in a loop for 36
hours (equivalent of pushing 550M IO operations). No issues were
observed. That suggest that the patch fixes the issue.
Fixes: f9f38e3338 ("nvme: improve performance for virtual NVMe devices")
Signed-off-by: Michal Wnukowski <wnukowski@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
[hch: updated changelog and comment a bit]
Signed-off-by: Christoph Hellwig <hch@lst.de>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAltU8z0eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG5X8H/2fJr7m3k242+t76
sitwvx1eoPqTgryW59dRKm9IuXAGA+AjauvHzaz1QxomeQa50JghGWefD0eiJfkA
1AphQ/24EOiAbbVk084dAI/C2p122dE4D5Fy7CrfLnuouyrbFaZI5STbnrRct7sR
9deeYW0GDHO1Uenp4WDCj0baaqJqaevZ+7GG09DnWpya2nQtSkGBjqn6GpYmrfOU
mqFuxAX8mEOW6cwK16y/vYtnVjuuMAiZ63/OJ8AQ6d6ArGLwAsdn7f8Fn4I4tEr2
L0d3CRLUyegms4++Dmlu05k64buQu46WlPhjCZc5/Ts4kjrNxBuHejj2/jeSnUSt
vJJlibI=
=42a5
-----END PGP SIGNATURE-----
Merge tag 'v4.18-rc6' into for-4.19/block2
Pull in 4.18-rc6 to get the NVMe core AEN change to avoid a
merge conflict down the line.
Signed-of-by: Jens Axboe <axboe@kernel.dk>
Also moved the logic of the remapping to the nvme core driver instead
of implementing it in the nvme pci driver. This way all the other nvme
transport drivers will benefit from it (in case they'll implement metadata
support).
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We will need to reference the controller in the setup and completion
time for tracing and future traffic based keep alive support.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The nvme driver specific structures need to be initialized prior to
enabling the generic controller so we can unwind on failure with out
using the reference counting callbacks so that 'probe' and 'remove'
can be symmetric.
The newly added iod_mempool is the only resource that was being
allocated out of order, and a failure there would leak the generic
controller memory. This patch just moves that allocation above the
controller initialization.
Fixes: 943e942e62 ("nvme-pci: limit max IO size and segments to avoid high order allocations")
Reported-by: Weiping Zhang <zwp10758@gmail.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
nvme requires an sg table allocation for each request. If the request
is large, then the allocation can become quite large. For instance,
with our default software settings of 1280KB IO size, we'll need
10248 bytes of sg table. That turns into a 2nd order allocation,
which we can't always guarantee. If we fail the allocation, blk-mq
will retry it later. But there's no guarantee that we'll EVER be
able to allocate that much contigious memory.
Limit the IO size such that we never need more than a single page
of memory. That's a lot faster and more reliable. Then back that
allocation with a mempool, so that we know we'll always be able
to succeed the allocation at some point.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Acked-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There is race between nvme_remove and nvme_reset_work that can
lead to io hang.
nvme_remove nvme_reset_work
-> nvme_remove_dead_ctrl
-> nvme_dev_disable
-> quiesce request_queue
-> queue remove_work
-> cancel_work_sync reset_work
-> nvme_remove_namespaces
-> splice ctrl->namespaces
nvme_remove_dead_ctrl_work
-> nvme_kill_queues
-> nvme_ns_remove do nothing
-> blk_cleanup_queue
-> blk_freeze_queue
Finally, the request_queue is quiesced state when wait freeze,
we will get io hang here. To fix it, move the nvme_kill_queues
from nvme_remove_dead_ctrl_work to nvme_remove_dead_ctrl.
Suggested-by: Keith Busch <keith.busch@linux.intel.com>
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
-----BEGIN PGP SIGNATURE-----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=N3BP
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20180608' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A few fixes for this merge window, where some of them should go in
sooner rather than later, hence a new pull this week. This pull
request contains:
- Set of NVMe fixes, mostly follow up cleanups/fixes to the queue
changes, but also teardown/removal and misc changes (Christop/Dan/
Johannes/Sagi/Steve).
- Two lightnvm fixes for issues that showed up in this window
(Colin/Wei).
- Failfast/driver flags inheritance for flush requests (Hannes).
- The md device put sanitization and fix (Kent).
- dm bio_set inheritance fix (me).
- nbd discard granularity fix (Josef).
- nbd consistency in command printing (Kevin).
- Loop recursion validation fix (Ted).
- Partition overlap check (Wang)"
[ .. and now my build is warning-free again thanks to the md fix - Linus ]
* tag 'for-linus-20180608' of git://git.kernel.dk/linux-block: (22 commits)
nvme: cleanup double shift issue
nvme-pci: make CMB SQ mod-param read-only
nvme-pci: unquiesce dead controller queues
nvme-pci: remove HMB teardown on reset
nvme-pci: queue creation fixes
nvme-pci: remove unnecessary completion doorbell check
nvme-pci: remove unnecessary nested locking
nvmet: filter newlines from user input
nvme-rdma: correctly check for target keyed sgl support
nvme: don't hold nvmf_transports_rwsem for more than transport lookups
nvmet: return all zeroed buffer when we can't find an active namespace
md: Unify mddev destruction paths
dm: use bioset_init_from_src() to copy bio_set
block: add bioset_init_from_src() helper
block: always set partition number to '0' in blk_partition_remap()
block: pass failfast and driver-specific flags to flush requests
nbd: set discard_alignment to the granularity
nbd: Consistently use request pointer in debug messages.
block: add verifier for cmdline partition
lightnvm: pblk: fix resource leak of invalid_bitmap
...
A controller reset after a run time change of the CMB module parameter
breaks the driver. An 'on -> off' will have the driver use NULL for the
host memory queue, and 'off -> on' will use mismatched queue depth between
the device and the host.
We could fix both, but there isn't really a good reason to change this
at run time anyway, compared to at module load time, so this patch makes
parameter read-only after after modprobe.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch ensures the nvme namsepace request queues are not quiesced
on a surprise removal. It's possible the queues were previously killed
in a failed reset, so the queues need to be unquiesced to ensure all
requests are flushed to completion.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The controller is required to disable its host memory buffer use on
controller reset. We don't need to submit an admin command to delete it,
so this patch skips sending that command so we don't need to worry about
handling a timeout.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We've been ignoring NVMe error status on queue creations. Fortunately they
are uncommon, but we should handle these anyway. This patch adds checks
for the a positive error return value that indicates an NVMe status.
If we do see a negative return, the controller isn't usable, so this
patch returns immediately in since we can't unwind that failure.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The nvme pci driver never unmaps the doorbell registers while the requests
are active, so we can always safely update the completion queue head.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The nvme pci driver no longer handles completions under the cq lock,
so the nested locking is not necessary.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=aFAi
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- unify AER decoding for native and ACPI CPER sources (Alexandru
Gagniuc)
- add TLP header info to AER tracepoint (Thomas Tai)
- add generic pcie_wait_for_link() interface (Oza Pawandeep)
- handle AER ERR_FATAL by removing and re-enumerating devices, as
Downstream Port Containment does (Oza Pawandeep)
- factor out common code between AER and DPC recovery (Oza Pawandeep)
- stop triggering DPC for ERR_NONFATAL errors (Oza Pawandeep)
- share ERR_FATAL recovery path between AER and DPC (Oza Pawandeep)
- disable ASPM L1.2 substate if we don't have LTR (Bjorn Helgaas)
- respect platform ownership of LTR (Bjorn Helgaas)
- clear interrupt status in top half to avoid interrupt storm (Oza
Pawandeep)
- neaten pci=earlydump output (Andy Shevchenko)
- avoid errors when extended config space inaccessible (Gilles Buloz)
- prevent sysfs disable of device while driver attached (Christoph
Hellwig)
- use core interface to report PCIe link properties in bnx2x, bnxt_en,
cxgb4, ixgbe (Bjorn Helgaas)
- remove unused pcie_get_minimum_link() (Bjorn Helgaas)
- fix use-before-set error in ibmphp (Dan Carpenter)
- fix pciehp timeouts caused by Command Completed errata (Bjorn
Helgaas)
- fix refcounting in pnv_php hotplug (Julia Lawall)
- clear pciehp Presence Detect and Data Link Layer Status Changed on
resume so we don't miss hotplug events (Mika Westerberg)
- only request pciehp control if we support it, so platform can use
ACPI hotplug otherwise (Mika Westerberg)
- convert SHPC to be builtin only (Mika Westerberg)
- request SHPC control via _OSC if we support it (Mika Westerberg)
- simplify SHPC handoff from firmware (Mika Westerberg)
- fix an SHPC quirk that mistakenly included *all* AMD bridges as well
as devices from any vendor with device ID 0x7458 (Bjorn Helgaas)
- assign a bus number even to non-native hotplug bridges to leave
space for acpiphp additions, to fix a common Thunderbolt xHCI
hot-add failure (Mika Westerberg)
- keep acpiphp from scanning native hotplug bridges, to fix common
Thunderbolt hot-add failures (Mika Westerberg)
- improve "partially hidden behind bridge" messages from core (Mika
Westerberg)
- add macros for PCIe Link Control 2 register (Frederick Lawler)
- replace IB/hfi1 custom macros with PCI core versions (Frederick
Lawler)
- remove dead microblaze and xtensa code (Bjorn Helgaas)
- use dev_printk() when possible in xtensa and mips (Bjorn Helgaas)
- remove unused pcie_port_acpi_setup() and portdrv_acpi.c (Bjorn
Helgaas)
- add managed interface to get PCI host bridge resources from OF (Jan
Kiszka)
- add support for unbinding generic PCI host controller (Jan Kiszka)
- fix memory leaks when unbinding generic PCI host controller (Jan
Kiszka)
- request legacy VGA framebuffer only for VGA devices to avoid false
device conflicts (Bjorn Helgaas)
- turn on PCI_COMMAND_IO & PCI_COMMAND_MEMORY in pci_enable_device()
like everybody else, not in pcibios_fixup_bus() (Bjorn Helgaas)
- add generic enable function for simple SR-IOV hardware (Alexander
Duyck)
- use generic SR-IOV enable for ena, nvme (Alexander Duyck)
- add ACS quirk for Intel 7th & 8th Gen mobile (Alex Williamson)
- add ACS quirk for Intel 300 series (Mika Westerberg)
- enable register clock for Armada 7K/8K (Gregory CLEMENT)
- reduce Keystone "link already up" log level (Fabio Estevam)
- move private DT functions to drivers/pci/ (Rob Herring)
- factor out dwc CONFIG_PCI Kconfig dependencies (Rob Herring)
- add DesignWare support to the endpoint test driver (Gustavo
Pimentel)
- add DesignWare support for endpoint mode (Gustavo Pimentel)
- use devm_ioremap_resource() instead of devm_ioremap() in dra7xx and
artpec6 (Gustavo Pimentel)
- fix Qualcomm bitwise NOT issue (Dan Carpenter)
- add Qualcomm runtime PM support (Srinivas Kandagatla)
- fix DesignWare enumeration below bridges (Koen Vandeputte)
- use usleep() instead of mdelay() in endpoint test (Jia-Ju Bai)
- add configfs entries for pci_epf_driver device IDs (Kishon Vijay
Abraham I)
- clean up pci_endpoint_test driver (Gustavo Pimentel)
- update Layerscape maintainer email addresses (Minghuan Lian)
- add COMPILE_TEST to improve build test coverage (Rob Herring)
- fix Hyper-V bus registration failure caused by domain/serial number
confusion (Sridhar Pitchai)
- improve Hyper-V refcounting and coding style (Stephen Hemminger)
- avoid potential Hyper-V hang waiting for a response that will never
come (Dexuan Cui)
- implement Mediatek chained IRQ handling (Honghui Zhang)
- fix vendor ID & class type for Mediatek MT7622 (Honghui Zhang)
- add Mobiveil PCIe host controller driver (Subrahmanya Lingappa)
- add Mobiveil MSI support (Subrahmanya Lingappa)
- clean up clocks, MSI, IRQ mappings in R-Car probe failure paths
(Marek Vasut)
- poll more frequently (5us vs 5ms) while waiting for R-Car data link
active (Marek Vasut)
- use generic OF parsing interface in R-Car (Vladimir Zapolskiy)
- add R-Car V3H (R8A77980) "compatible" string (Sergei Shtylyov)
- add R-Car gen3 PHY support (Sergei Shtylyov)
- improve R-Car PHYRDY polling (Sergei Shtylyov)
- clean up R-Car macros (Marek Vasut)
- use runtime PM for R-Car controller clock (Dien Pham)
- update arm64 defconfig for Rockchip (Shawn Lin)
- refactor Rockchip code to facilitate both root port and endpoint
mode (Shawn Lin)
- add Rockchip endpoint mode driver (Shawn Lin)
- support VMD "membar shadow" feature (Jon Derrick)
- support VMD bus number offsets (Jon Derrick)
- add VMD "no AER source ID" quirk for more device IDs (Jon Derrick)
- remove unnecessary host controller CONFIG_PCIEPORTBUS Kconfig
selections (Bjorn Helgaas)
- clean up quirks.c organization and whitespace (Bjorn Helgaas)
* tag 'pci-v4.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (144 commits)
PCI/AER: Replace struct pcie_device with pci_dev
PCI/AER: Remove unused parameters
PCI: qcom: Include gpio/consumer.h
PCI: Improve "partially hidden behind bridge" log message
PCI: Improve pci_scan_bridge() and pci_scan_bridge_extend() doc
PCI: Move resource distribution for single bridge outside loop
PCI: Account for all bridges on bus when distributing bus numbers
ACPI / hotplug / PCI: Drop unnecessary parentheses
ACPI / hotplug / PCI: Mark stale PCI devices disconnected
ACPI / hotplug / PCI: Don't scan bridges managed by native hotplug
PCI: hotplug: Add hotplug_is_native()
PCI: shpchp: Add shpchp_is_native()
PCI: shpchp: Fix AMD POGO identification
PCI: mobiveil: Add MSI support
PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver
PCI/AER: Decode Error Source Requester ID
PCI/AER: Remove aer_recover_work_func() forward declaration
PCI/DPC: Use the generic pcie_do_fatal_recovery() path
PCI/AER: Pass service type to pcie_do_fatal_recovery()
PCI/DPC: Disable ERR_NONFATAL handling by DPC
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nga/
-----END PGP SIGNATURE-----
Merge tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- clean up how we pass around gfp_t and
blk_mq_req_flags_t (Christoph)
- prepare us to defer scheduler attach (Christoph)
- clean up drivers handling of bounce buffers (Christoph)
- fix timeout handling corner cases (Christoph/Bart/Keith)
- bcache fixes (Coly)
- prep work for bcachefs and some block layer optimizations (Kent).
- convert users of bio_sets to using embedded structs (Kent).
- fixes for the BFQ io scheduler (Paolo/Davide/Filippo)
- lightnvm fixes and improvements (Matias, with contributions from Hans
and Javier)
- adding discard throttling to blk-wbt (me)
- sbitmap blk-mq-tag handling (me/Omar/Ming).
- remove the sparc jsflash block driver, acked by DaveM.
- Kyber scheduler improvement from Jianchao, making it more friendly
wrt merging.
- conversion of symbolic proc permissions to octal, from Joe Perches.
Previously the block parts were a mix of both.
- nbd fixes (Josef and Kevin Vigor)
- unify how we handle the various kinds of timestamps that the block
core and utility code uses (Omar)
- three NVMe pull requests from Keith and Christoph, bringing AEN to
feature completeness, file backed namespaces, cq/sq lock split, and
various fixes
- various little fixes and improvements all over the map
* tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block: (196 commits)
blk-mq: update nr_requests when switching to 'none' scheduler
block: don't use blocking queue entered for recursive bio submits
dm-crypt: fix warning in shutdown path
lightnvm: pblk: take bitmap alloc. out of critical section
lightnvm: pblk: kick writer on new flush points
lightnvm: pblk: only try to recover lines with written smeta
lightnvm: pblk: remove unnecessary bio_get/put
lightnvm: pblk: add possibility to set write buffer size manually
lightnvm: fix partial read error path
lightnvm: proper error handling for pblk_bio_add_pages
lightnvm: pblk: fix smeta write error path
lightnvm: pblk: garbage collect lines with failed writes
lightnvm: pblk: rework write error recovery path
lightnvm: pblk: remove dead function
lightnvm: pass flag on graceful teardown to targets
lightnvm: pblk: check for chunk size before allocating it
lightnvm: pblk: remove unnecessary argument
lightnvm: pblk: remove unnecessary indirection
lightnvm: pblk: return NVM_ error on failed submission
lightnvm: pblk: warn in case of corrupted write buffer
...
With recent CQ handling improvements we can now move the locking into
__nvme_submit_cmd. Also remove the local tail variable to make the code
more obvious, remove the __ prefix in the name, and fix the comments
describing the function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
The block layer's timeout handling currently prevents drivers from
completing commands outside the timeout callback once blk-mq decides
they've expired. If a device breaks, this could potentially create many
thousands of timed out commands. There's nothing of value to be gleaned
from observing each of those messages, so this patch adds a rate limit
on them.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Pull NVMe changes from Christoph:
"Here is the current batch of nvme updates for 4.18, we have a few more
patches in the queue, but I'd like to get this pile into your tree
and linux-next ASAP.
The biggest item is support for file-backed namespaces in the NVMe
target from Chaitanya, in addition to that we mostly small fixes from
all the usual suspects."
* 'nvme-4.18-2' of git://git.infradead.org/nvme:
nvme: fixup memory leak in nvme_init_identify()
nvme: fix KASAN warning when parsing host nqn
nvmet-loop: use nr_phys_segments when map rq to sgl
nvmet-fc: increase LS buffer count per fc port
nvmet: add simple file backed ns support
nvmet: remove duplicate NULL initialization for req->ns
nvmet: make a few error messages more generic
nvme-fabrics: allow duplicate connections to the discovery controller
nvme-fabrics: centralize discovery controller defaults
nvme-fabrics: remove unnecessary controller subnqn validation
nvme-fc: remove setting DNR on exception conditions
nvme-rdma: stop admin queue before freeing it
nvme-pci: Fix AER reset handling
nvme-pci: set nvmeq->cq_vector after alloc cq/sq
nvme: host: core: fix precedence of ternary operator
nvme: fix lockdep warning in nvme_mpath_clear_current_path
NVMe always completes the request before returning from ->timeout, either
by polling for it, or by disabling the controller. Return BLK_EH_DONE so
that the block layer doesn't even try to complete it again.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Keith Busch