With the implementation of the system reset controller we lost a setting
that is currently applied by the bootloader and which configures the IMP
port for 2Gb/sec, the default is 1Gb/sec. This is needed given the
number of ports and applications we expect to run so bring back that
setting.
Fixes: 01b0ac07589e ("net: dsa: bcm_sf2: Add support for optional reset controller line")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105_parse_ports_node function was tested only on device trees
where all ports were enabled. Fix this check so that the driver
continues to probe only with the ports where status is not "disabled",
as expected.
Fixes: 8aa9ebccae ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 family uses an extended register to set the port connected to
the CPU. The lower 5 bits indicate the port, the upper three bits are
the priority of the frames as they pass through the switch, what
egress queue they should use, etc. Since frames being set to the CPU
are typically management frames, BPDU, IGMP, ARP, etc set the priority
to 7, the reset default, and the highest.
Fixes: 33641994a6 ("net: dsa: mv88e6xxx: Monitor and Management tables")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_port_set_cmode() relies on cmode stored in struct
mv88e6xxx_port to skip cmode update when the requested value matches the
cached value. It turns out that mv88e6xxx_port_hidden_write() might
change the port cmode setting as a side effect, so we can't rely on the
cached value to determine that cmode update in not necessary.
Force cmode update in mv88e6341_port_set_cmode(), to make
serdes configuration work again. Other mv88e6xxx_port_set_cmode()
callers keep the current behaviour.
This fixes serdes configuration of the 6141 switch on SolidRun Clearfog
GT-8K.
Fixes: 7a3007d22e ("net: dsa: mv88e6xxx: fully support SERDES on Topaz family")
Reported-by: Denis Odintsov <d.odintsov@traviangames.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For first-generation switches (SJA1105E and SJA1105T):
- TPID means C-Tag (typically 0x8100)
- TPID2 means S-Tag (typically 0x88A8)
While for the second generation switches (SJA1105P, SJA1105Q, SJA1105R,
SJA1105S) it is the other way around:
- TPID means S-Tag (typically 0x88A8)
- TPID2 means C-Tag (typically 0x8100)
In other words, E/T tags untagged traffic with TPID, and P/Q/R/S with
TPID2.
So the patch mentioned below fixed VLAN filtering for P/Q/R/S, but broke
it for E/T.
We strive for a common code path for all switches in the family, so just
lie in the static config packing functions that TPID and TPID2 are at
swapped bit offsets than they actually are, for P/Q/R/S. This will make
both switches understand TPID to be ETH_P_8021Q and TPID2 to be
ETH_P_8021AD. The meaning from the original E/T was chosen over P/Q/R/S
because E/T is actually the one with public documentation available
(UM10944.pdf).
Fixes: f9a1a7646c ("net: dsa: sja1105: Reverse TPID and TPID2")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check originates from the initial implementation which was not based
on PTP time but on a standalone clock source. In the meantime we can now
program the PTPSCHTM register at runtime with the dynamic base time
(actually with a value that is 200 ns smaller, to avoid writing DELTA=0
in the Schedule Entry Points Parameters Table). And we also have logic
for moving the actual base time in the future of the PHC's current time
base, so the check for zero serves no purpose, since even if the user
will specify zero, that's not what will end up in the static config
table where the limitation is.
Fixes: 86db36a347 ("net: dsa: sja1105: Implement state machine for TAS with PTP clock source")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When activating tc-taprio offload on the switch ports, the TAS state
machine will try to check whether it is running or not, but will find
both the STARTED and STOPPED bits as false in the
sja1105_tas_check_running function. So the function will return -EINVAL
(an abnormal situation) and the kernel will keep printing this from the
TAS FSM workqueue:
[ 37.691971] sja1105 spi0.1: An operation returned -22
The reason is that the underlying function that gets called,
sja1105_ptp_commit, does not actually do a SPI_READ, but a SPI_WRITE. So
the command buffer remains initialized with zeroes instead of retrieving
the hardware state. Fix that.
Fixes: 41603d78b3 ("net: dsa: sja1105: Make the PTP command read-write")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP egress timestamp N must be captured from register PTPEGR_TS[n],
where n = 2 * PORT + TSREG. There are 10 PTPEGR_TS registers, 2 per
port. We are only using TSREG=0.
As opposed to the management slots, which are 4 in number
(SJA1105_NUM_PORTS, minus the CPU port). Any management frame (which
includes PTP frames) can be sent to any non-CPU port through any
management slot. When the CPU port is not the last port (#4), there will
be a mismatch between the slot and the port number.
Luckily, the only mainline occurrence with this switch
(arch/arm/boot/dts/ls1021a-tsn.dts) does have the CPU port as #4, so the
issue did not manifest itself thus far.
Fixes: 47ed985e97 ("net: dsa: sja1105: Add logic for TX timestamping")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP fragment is specified through user-defined field as the first
bit of the first user-defined word. We were previously trying to extract
it from the user-defined mask which could not possibly work. The ip_frag
is also supposed to be a boolean, if we do not cast it as such, we risk
overwriting the next fields in CFP_DATA(6) which would render the rule
inoperative.
Fixes: 7318166cac ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Selecting MSCC_OCELOT_SWITCH is not possible when NET_VENDOR_MICROSEMI
is disabled:
WARNING: unmet direct dependencies detected for MSCC_OCELOT_SWITCH
Depends on [n]: NETDEVICES [=y] && ETHERNET [=n] && NET_VENDOR_MICROSEMI [=n] && NET_SWITCHDEV [=y] && HAS_IOMEM [=y]
Selected by [m]:
- NET_DSA_MSCC_FELIX [=m] && NETDEVICES [=y] && HAVE_NET_DSA [=y] && NET_DSA [=y] && PCI [=y]
Add a Kconfig dependency on NET_VENDOR_MICROSEMI, which also implies
CONFIG_NETDEVICES.
Depending on a vendor config violates menuconfig locality for the DSA
driver, but is the smallest compromise since all other solutions are
much more complicated (see [0]).
https://www.spinics.net/lists/netdev/msg618808.html
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were several issues with 53568438e3 ("net: dsa: b53: Add support for port_egress_floods callback") that resulted in breaking connectivity for standalone ports:
- both user and CPU ports must allow unicast and multicast forwarding by
default otherwise this just flat out breaks connectivity for
standalone DSA ports
- IP multicast is treated similarly as multicast, but has separate
control registers
- the UC, MC and IPMC lookup failure register offsets were wrong, and
instead used bit values that are meaningful for the
B53_IP_MULTICAST_CTRL register
Fixes: 53568438e3 ("net: dsa: b53: Add support for port_egress_floods callback")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function was using configuration of port 0 in devicetree for all ports.
In case CPU port was not 0, the delay settings was ignored. This resulted not
working communication between CPU and the switch.
Fixes: f5b8631c29 ("net: dsa: sja1105: Error out if RGMII delays are requested in DT")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following sparse warnings:
drivers/net/dsa/ocelot/felix.c:351:6: warning: symbol 'felix_txtstamp' was not declared. Should it be static?
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to reuse ocelot functions as possible to enable PTP
clock and to support hardware timestamping on Felix.
On TX path, timestamping works on packet which requires timestamp.
The injection header will be configured accordingly, and skb clone
requires timestamp will be added into a list. The TX timestamp
is final handled in threaded interrupt handler when PTP timestamp
FIFO is ready.
On RX path, timestamping is always working. The RX timestamp could
be got from extraction header.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to define PTP registers for felix_vsc9959.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the NXP LS1028A, there are 2 Ethernet links between the Felix switch
and the ENETC:
- eno2 <-> swp4, at 2.5G
- eno3 <-> swp5, at 1G
Only one of the above Ethernet port pairs can act as a DSA link for
tagging.
When adding initial support for the driver, it was tested only on the 1G
eno3 <-> swp5 interface, due to the necessity of using PHYLIB initially
(which treats fixed-link interfaces as emulated C22 PHYs, so it doesn't
support fixed-link speeds higher than 1G).
After making PHYLINK work, it appears that swp4 still can't act as CPU
port. So it looks like ocelot_set_cpu_port was being called for swp4,
but then it was called again for swp5, overwriting the CPU port assigned
in the DT.
It appears that when you call dsa_upstream_port for a port that is not
defined in the device tree (such as swp5 when using swp4 as CPU port),
its dp->cpu_dp pointer is not initialized by dsa_tree_setup_default_cpu,
and this trips up the following condition in dsa_upstream_port:
if (!cpu_dp)
return port;
So the moral of the story is: don't call dsa_upstream_port for a port
that is not defined in the device tree, and therefore its dsa_port
structure is not completely initialized (ds->num_ports is still 6).
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver enables rising edge or falling edge, but not both, and so
this patch validates that the request contains only one of the two
edges.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
User space may request time stamps on rising edges, falling edges, or
both. However, the particular mode may or may not be supported in the
hardware or in the driver. This patch adds a "strict" flag that tells
drivers to ensure that the requested mode will be honored.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the mv88e6xxx PTP support to explicitly reject any future flags that
get added to the external timestamp request ioctl.
In order to maintain currently functioning code, this patch accepts all
three current flags. This is because the PTP_RISING_EDGE and
PTP_FALLING_EDGE flags have unclear semantics and each driver seems to
have interpreted them slightly differently.
For the record, the semantics of this driver are:
flags Meaning
---------------------------------------------------- --------------------------
PTP_ENABLE_FEATURE Time stamp falling edge
PTP_ENABLE_FEATURE|PTP_RISING_EDGE Time stamp rising edge
PTP_ENABLE_FEATURE|PTP_FALLING_EDGE Time stamp falling edge
PTP_ENABLE_FEATURE|PTP_RISING_EDGE|PTP_FALLING_EDGE Time stamp rising edge
Cc: Brandon Streiff <brandon.streiff@ni.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This supports an Ethernet switching core from Vitesse / Microsemi /
Microchip (VSC9959) which is part of the Ocelot family (a brand name),
and whose code name is Felix. The switch can be (and is) integrated on
different SoCs as a PCIe endpoint device.
The functionality is provided by the core of the Ocelot switch driver
(drivers/net/ethernet/mscc). In this regard, the current driver is an
instance of Microsemi's Ocelot core driver, with a DSA front-end. It
inherits its name from VSC9959's code name, to distinguish itself from
the switchdev ocelot driver.
The patch adds the logic for probing a PCI device and defines the
register map for the VSC9959 switch core, since it has some differences
in register addresses and bitfield mappings compared to the other Ocelot
switches (VSC7511, VSC7512, VSC7513, VSC7514).
The Felix driver declares the register map as part of the "instance
table". Currently the VSC9959 inside NXP LS1028A is the only instance,
but presumably it can support other switches in the Ocelot family, when
used in DSA mode (Linux running on the external CPU, and not on the
embedded MIPS).
In a few cases, some h/w operations have to be done differently on
VSC9959 due to missing bitfields. This is the case for the switch core
reset and init. Because for this operation Ocelot uses some bits that
are not present on Felix, the latter has to use a register from the
global registers block (GCB) instead.
Although it is a PCI driver, it relies on DT bindings for compatibility
with DSA (CPU port link, PHY library). It does not have any custom
device tree bindings, since we would like to minimize its dependency on
device tree though.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't really need 10k species of reset. Remove everything except cold
reset which is what is actually used. Too bad the hardware designers
couldn't agree to use the same bit field for rev 1 and rev 2, so the
(*reset_cmd) function pointer is there to stay.
However let's simplify the prototype and give it a struct dsa_switch (we
want to avoid forward-declarations of structures, in this case struct
sja1105_private, wherever we can).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested using the following bash script and the tc from iproute2-next:
#!/bin/bash
set -e -u -o pipefail
NSEC_PER_SEC="1000000000"
gatemask() {
local tc_list="$1"
local mask=0
for tc in ${tc_list}; do
mask=$((${mask} | (1 << ${tc})))
done
printf "%02x" ${mask}
}
if ! systemctl is-active --quiet ptp4l; then
echo "Please start the ptp4l service"
exit
fi
now=$(phc_ctl /dev/ptp1 get | gawk '/clock time is/ { print $5; }')
# Phase-align the base time to the start of the next second.
sec=$(echo "${now}" | gawk -F. '{ print $1; }')
base_time="$(((${sec} + 1) * ${NSEC_PER_SEC}))"
tc qdisc add dev swp5 parent root handle 100 taprio \
num_tc 8 \
map 0 1 2 3 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time ${base_time} \
sched-entry S $(gatemask 7) 100000 \
sched-entry S $(gatemask "0 1 2 3 4 5 6") 400000 \
clockid CLOCK_TAI flags 2
The "state machine" is a workqueue invoked after each manipulation
command on the PTP clock (reset, adjust time, set time, adjust
frequency) which checks over the state of the time-aware scheduler.
So it is not monitored periodically, only in reaction to a PTP command
typically triggered from a userspace daemon (linuxptp). Otherwise there
is no reason for things to go wrong.
Now that the timecounter/cyclecounter has been replaced with hardware
operations on the PTP clock, the TAS Kconfig now depends upon PTP and
the standalone clocksource operating mode has been removed.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTPSTRTSCH and PTPSTOPSCH bits are actually readable and indicate
whether the time-aware scheduler is running or not. We will be using
that for monitoring the scheduler in the next patch, so refactor the PTP
command API in order to allow that.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes it can be quite opaque even for me why the driver decided to
reset the switch. So instead of adding dump_stack() calls each time for
debugging, just add a reset reason to sja1105_static_config_reload
calls which gets printed to the console.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a stray semicolon in an if statement that will cause a dev_err
message to be printed unconditionally. Fix this by removing the stray
semicolon.
Addresses-Coverity: ("Stay semicolon")
Fixes: f0942e00a1 ("net: dsa: mv88e6xxx: Add support for port mirroring")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring port mirroring through the cls_matchall
classifier. We do a full ingress and/or egress capture towards a
capture port. It allows setting a different capture port for ingress
and egress traffic.
It keeps track of the mirrored ports and the destination ports to
prevent changes to the capture port while other ports are being
mirrored.
Signed-off-by: Iwan R Timmer <irtimmer@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the configuration of the egress and ingress monitor port.
This allows the port mirror functionality to do ingress and egress
port mirroring to separate ports.
Signed-off-by: Iwan R Timmer <irtimmer@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose here is to avoid ptp4l fail due to this condition:
timed out while polling for tx timestamp
increasing tx_timestamp_timeout may correct this issue, but it is likely caused by a driver bug
port 1: send peer delay request failed
So either reset the switch before the management frame was sent, or
after it was timestamped as well, but not in the middle.
The condition may arise either due to a true timeout (i.e. because
re-uploading the static config takes time), or due to the TX timestamp
actually getting lost due to reset. For the former we can increase
tx_timestamp_timeout in userspace, for the latter we need this patch.
Locking all traffic during switch reset does not make sense at all,
though. Forcing all CPU-originated traffic to potentially block waiting
for a sleepable context to send > 800 bytes over SPI is not a good idea.
Flows that are autonomously forwarded by the switch will get dropped
anyway during switch reset no matter what. So just let all other
CPU-originated traffic be dropped as well.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP time of the switch is not preserved when uploading a new static
configuration. Work around this hardware oddity by reading its PTP time
before a static config upload, and restoring it afterwards.
Static config changes are expected to occur at runtime even in scenarios
directly related to PTP, i.e. the Time-Aware Scheduler of the switch is
programmed in this way.
Perhaps the larger implication of this patch is that the PTP .gettimex64
and .settime functions need to be exposed to sja1105_main.c, where the
PTP lock needs to be held during this entire process. So their core
implementation needs to move to some common functions which get exposed
in sja1105_ptp.h.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Through the PTP_SYS_OFFSET_EXTENDED ioctl, it is possible for userspace
applications (i.e. phc2sys) to compensate for the delays incurred while
reading the PHC's time.
The task itself of taking the software timestamp is delegated to the SPI
subsystem, through the newly introduced API in struct spi_transfer. The
goal is to cross-timestamp I/O operations on the switch's PTP clock with
values in the local system clock (CLOCK_REALTIME). For that we need to
understand a bit of the hardware internals.
The 'read PTP time' message is a 12 byte structure, first 4 bytes of
which represent the SPI header, and the last 8 bytes represent the
64-bit PTP time. The switch itself starts processing the command
immediately after receiving the last bit of the address, i.e. at the
middle of byte 3 (last byte of header). The PTP time is shadowed to a
buffer register in the switch, and retrieved atomically during the
subsequent SPI frames.
A similar thing goes on for the 'write PTP time' message, although in
that case the switch waits until the 64-bit PTP time becomes fully
available before taking any action. So the byte that needs to be
software-timestamped is byte 11 (last) of the transfer.
The patch creates a common (and local) sja1105_xfer implementation for
the SPI I/O, and offers 3 front-ends:
- sja1105_xfer_u32 and sja1105_xfer_u64: these are capable of optionally
requesting a PTP timestamp
- sja1105_xfer_buf: this is for large transfers (e.g. the static config
buffer) and other misc data, and there is no point in giving
timestamping capabilities to this.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_g2_atu_stats_get() takes two parameters. Make the stub
function also take two, otherwise we get compile errors.
Fixes: c5f299d592 ("net: dsa: mv88e6xxx: global1_atu: Add helper for get next")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ATU can report how many entries it contains. It does this per bin,
there being 4 bins in total. Export the ATU as a devlink resource, and
provide a method the needed callback to get the resource occupancy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When retrieving the ATU statistics, and ATU get next has to be
performed to trigger the ATU to collect the statistics. Export a
helper from global1_atu to perform this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each supported switch, add an entry to the info structure for the
number of MACs which can be stored in the ATU. This will later be used
to export the ATU as a devlink resource, and indicate its occupancy,
how full the ATU is.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grab an optional and exclusive reset controller line for the switch and
manage it during probe/remove functions accordingly. For 7278 devices we
change bcm_sf2_sw_rst() to use the reset controller line since the
WATCHDOG_CTRL register does not reset the switch contrary to stated
documentation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the DSA core doing the call to dsa_port_disable() we do not need to
do that within the driver itself. This could cause an use after free
since past dsa_unregister_switch() we should not be accessing any
dsa_switch internal structures.
Fixes: 0394a63acf ("net: dsa: enable and disable all ports")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it became possible for the DSA core to use a CPU port different
than 8, our bcm_sf2_imp_setup() function was broken because it assumes
that registers are applicable to port 8. In particular, the port's MAC
is going to stay disabled, so make sure we clear the RX_DIS and TX_DIS
bits if we are not configured for port 8.
Fixes: 9f91484f6f ("net: dsa: make "label" property optional for dsa2")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a new list of DSA links in the switch fabric itself, to
provide an alterative to the ds->rtable static arrays.
At the same time, provide a new dsa_routing_port() helper to abstract
the usage of ds->rtable in drivers. If there's no port to reach a
given device, return the first invalid port, ds->num_ports. This avoids
potential signedness errors or the need to define special values.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When NET_DSA_SMSC_LAN9303=y and NET_DSA_SMSC_LAN9303_MDIO=y,
below errors can be seen:
drivers/net/dsa/lan9303_mdio.c:87:23: error: REGMAP_ENDIAN_LITTLE
undeclared here (not in a function)
.reg_format_endian = REGMAP_ENDIAN_LITTLE,
drivers/net/dsa/lan9303_mdio.c:93:3: error: const struct regmap_config
has no member named reg_read
.reg_read = lan9303_mdio_read,
It should select REGMAP in config NET_DSA_SMSC_LAN9303.
Fixes: dc70058315 ("net: dsa: LAN9303: add MDIO managed mode support")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An earlier bugfix introduced a dependency on CONFIG_NET_SCH_TAPRIO,
but this missed the case of NET_SCH_TAPRIO=m and NET_DSA_SJA1105=y,
which still causes a link error:
drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_setup_tc_taprio':
sja1105_tas.c:(.text+0x5c): undefined reference to `taprio_offload_free'
sja1105_tas.c:(.text+0x3b4): undefined reference to `taprio_offload_get'
drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_tas_teardown':
sja1105_tas.c:(.text+0x6ec): undefined reference to `taprio_offload_free'
Change the dependency to only allow selecting the TAS code when it
can link against the taprio code.
Fixes: a8d570de0c ("net: dsa: sja1105: Add dependency for NET_DSA_SJA1105_TAS")
Fixes: 317ab5b86c ("net: dsa: sja1105: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the marvell switches have bits controlling the hash algorithm
the ATU uses for MAC addresses. In some industrial settings, where all
the devices are from the same manufacture, and hence use the same OUI,
the default hashing algorithm is not optimal. Allow the other
algorithms to be selected via devlink.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leverage the recently add b53_mdb_{add,del,prepare} functions since they
work as-is for bcm_sf2.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting IGMP snooping with or without the use of
a bridge, add support within b53_common.c to program the ARL entries for
multicast operations. The key difference is that a multicast ARL entry
is comprised of a bitmask of enabled ports, instead of a port number.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 0394a63acf ("net: dsa: enable and disable all ports")
the dsa core disables all unused ports of a switch. In this case
disabling ports with numbers higher than QCA8K_NUM_PORTS causes that
some switch registers are overwritten with incorrect content.
To fix this, initialize the dsa_switch->num_ports with correct number
of ports.
Fixes: 7e99e34701 ("net: dsa: remove dsa_switch_alloc helper")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli